Scribd
Upload
221 views4 pages

Sun ILOM - T5220, T5240, x4600, X4450 Configure: 1. Connect To The ILOM Using Serial Port

ILOM is a system controller that provides remote management capabilities for Oracle Sun server hardware like the T5120 and T5220. It monitors temperatures, voltages, disks, fans, CPUs and power supplies. ILOM allows setting up user accounts and changing passwords. It can also be configured to send hardware alerts via SNMP. Network time and settings can be configured through ILOM. Once the network configuration is set, SSH, HTTP and HTTPS services can be enabled to allow remote access and management of the server through the ILOM web interface.

Uploaded by

Muhammed Mugari
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
221 views4 pages

Sun ILOM - T5220, T5240, x4600, X4450 Configure: 1. Connect To The ILOM Using Serial Port

ILOM is a system controller that provides remote management capabilities for Oracle Sun server hardware like the T5120 and T5220. It monitors temperatures, voltages, disks, fans, CPUs and power supplies. ILOM allows setting up user accounts and changing passwords. It can also be configured to send hardware alerts via SNMP. Network time and settings can be configured through ILOM. Once the network configuration is set, SSH, HTTP and HTTPS services can be enabled to allow remote access and management of the server through the ILOM web interface.

Uploaded by

Muhammed Mugari
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Sun ILOM T5220, T5240, x4600, X4450 configure

at 23:47 Lingeswaran R Solaris Hardware

ILOM is an independent system controller providing a command-line interface and web based interface on T-series oracle sun server hardware's like T5120, T5220, T5240, T5440 T3, T-4 servers.It can monitor system temperature,voltages,internal disks, chassis fans,CPU's and power supplies.We can configure ilom with snmp to send hardware alerts.ILOM provides remote system administration and Java web-based console provides much easier than the command line.Another important feature is host control.We can switch on and switch off the system remotely. Here we will see step by step procedure of configuring ILOM: 1. Connect to the ILOM using serial port: Ensure that the serial port on your connecting device is set to the following.Normally we will use hyper terminal for this. Parameters: 9600 baudrate 8 bits No parity 1 stop bit No handshaking

Establish an ILOM service processor session.See the ILOM users guide for instructions. Type the default user name root Type the default password changeme 2. Set User accounts: After logging in to ILOM console,creating new account called admin
-> cd /SP/users -> create admin role=administrator Creating user Created /SP/users/admin -> set root password You will be prompted for a password, change to new password

3. Set SP Hostname:
-> set /SP hostname=server hostname-lom Set hostname to server hostname-lom

4. Set Network time:


-> set /SP/clients/ntp/server/1 address=xx.xx.xx.xxx Set address to xx.xx.xx.xxx

-> set /SP/clients/ntp/server/2 address=xx.xx.xx.xxx Set address to xx.xx.xx.xxx -> show /SP/clients/ntp/server/1 /SP/clients/ntp/server/1 Targets: Properties: address = xx.xx.xx.xxx Commands: cd set show -> show /SP/clients/ntp/server/2 /SP/clients/ntp/server/2 Targets: Properties: address = xx.xx.xx.xxx Commands: cd set show -> cd /SP/clock /SP/clock -> set usentpserver=enabled Set usentpserver to enabled /SP/clock -> show Targets: Properties: datetime = Thu May 3 13:47:51 2010 usentpserver = enabled Commands: cd

set show

5. Set Network Configuration: Connect an Ethernet cable to the network management port.
-> cd /SP/network Refer to CMDB for ipaddress,netmask,gateway -> set pendingipaddress=nnn.nnn.nnn.nnn -> set pendingipnetmask=xxx.xxx.xxx.xxx -> set pendingipgateway=ggg.ggg.ggg.ggg -> set pendingipdiscovery=static -> set commitpending=true -> show

6. Set SSH access and HTTP(S):


-> cd /SP/services -> set ssh state=enabled -> set http servicestate=enabled -> set http secureredirect=enabled -> set https servicestate=enabled -> show ssh state /SP/services/ssh Properties: state = enabled -> show http /SP/services/http Targets: Properties: port = 80 secureredirect = enabled servicestate = enabled -> show https

/SP/services/https Targets: ssl Properties: port = 443 servicestate = enabled

Now you will able to use system console remotely by using console IP on ssh service and http web service.To access web-based Ilom console,just enter the console IP in browser and access web console. Thank you for reading this article.Please leave a comment if you have any doubt ,i will get back to you as soon as possible.

You might also like