MULTIFLEX

The flexible girder formwork for slabs

on individual props

on falsework systems

Product range 9.10

Edition 08/2002 PERI GmbH P.O. Box 12 64 89259 Weissenhorn Tel.: 0 73 09 / 9 50-0 Fax: 0 73 09 / 9 51-0 [email protected] www.peri.de

Important notes: Our products are to be used in accordance with the relevant state and national safety regulations. The illustrations in this brochure are photographs of the situation on a site at a particular moment. Safety or formwork anchorage details are therefore not to be taken as a definitive guide to the way the equipment is to be used. Safety precautions and allowable loads are to be observed exactly. Separate structural calculations are required for any changes or deviations. Subject to technical change in the interest of progress.

26

PERI Formwork Engineering

Contents
The essentials in pictures MULTIFLEX options Flexible and adaptable For any layout and any height Formwork girders Props Planning Quicker and more reliable with ELPOS Design example General applications Example of use Erection Striking Special applications Custom solutions Beams Stopends Design tables Extract from the PERI book of tables Range PERI International

Page

2-3 4-5 6-7 8-9 10-11

12-13 14-15

16-17 18-19 20-21

22 23 24-25

26-33 34-45 48-49

PERI Formwork Engineering

1. Main girders: VT 20K Sec. girders: VT 20K

50

50

50

50

50

50

50

Secondary girders Main girders

90

90

90

90

F co e w fa m e r st p a er on nd sh en li ut ts gh te m te ri e a r ng n !
2,50

MULTIFLEX options 4 ways of shuttering cost-effectively

2,50

2. Main girders: GT 24 Sec. girders: VT 20K

50

50

50

50

50

50

50

1,15

1,15

1,15

2,50

2,50

3. Main girders: GT 24 Sec. girders: GT 24

625

625

625

625

625

1,00

1,00

1,00

2,88

2,88

4. Main girders: 2x GT 24 Sec. girders: GT 24

625

625

625

625

625

1,80

1,80

2,88

2,88 PERI Formwork Engineering

Example for 30 cm thick slab Comp./m2 kg/m2 Props/m2 Main and secondary girders of the same type simplify stocks and distribution. Largest number of props and individual components and heaviest formwork make shuttering slow.

2,77 37. 2. 37,8 0. 0,44 2,59 36. 2. 36,4 0. 0,35 2,26 32. 2. 32,4 0. 0,35 2,01 32. 2. 32,0 0. 0,23
PERI Formwork Engineering

Most cost-effective solution in terms of equipment. With the 24 clawhead the GT 24 girder can be supported at any point and transfer the maximum load of 28 kN. Fewer props, fewer components, faster shuttering.

Main and secondary girders of the same type simplify stocks and distribution. GT 24 main and secondary girders achieve a service life that represents a long-term investment. Fewer components for even faster shuttering.

Main and secondary girders of the same type simplify stocks and distribution. GT 24 primary and secondary girders achieve a service life that represents a long-term investment. Preferred application is industrial buildings with thick slabs in combination with MULTIPROPs. Fewest props and components and fastest shuttering.

PERI MULTIFLEX The flexible and adaptable girder slab formwork

PERI MULTIFLEX with GT 24 main girders and VT 20 K secondary girders in an administration building

PERI MULTIFLEX, the girder formwork for any layout and any height. You can use the GT 24 lattice girder or the VT 20K solid formwork girder. With PERI MULTIFLEX you always shutter cost-effectively and efficiently. s Using the universal, rigid and longlasting GT 24 lattice girder allows large spacings for main, secondary girders and supports. The GT 24 reduces the number of components to be erected and struck. s The VT 20K girder with its highgrade web board is the economical way of supporting thinner slabs.

PERI MULTIFLEX slide rule simplifies planning.

a
d [m] Deckenstrke 2 [kN/ m ] Belastung q b [m] gerabstand Zulssiger Jochtr [kN] Sttzenlast F Vorhandene and a [m] Quertrgerabst Sttzenabstand c [m] 0,60 0,90 1,20 1,50 1,80 2,10
Belastung: Durchbiegung: Nach DIN 4421 500 l/ Beschrnkt auf Dreischichtplatte dlage ist eine und Berechnungsgrun N/mm2 (durchfeuchtet) 2 21 mm mit E=7500 (durchfeuchtet). = 6,5 N/mm zulssiger B

MULTIFLEX 20 VT 20 / VT

Deckenstrke d [m] 2 Belastung q [kN/ m ] Zulssiger Jochtrgerabstand b [m] Vorhandene Sttzenlast F [kN] 2002 Ausgabe Quertrgerabstand a [m] Sttzenabstand c [m]

2,40

Beispiel : d = 0,25 m Deckenstrke Vorhandene 3-S, 21 mm ut 3-S-Platte Gewhlte Schalha a = 0,50 m gerabstand Gewhlter Quertr c = 0,90 m tzenabstand Gewhlter St b = 2,70 m gerabstand Zulssiger Jochtr F= 20,4 kN Sttzenlast Vorhandene

0,60 0,90 1,20

MULTIFLEX GT 24 / GT 24
c

1,50 1,80 2,10 2,40

Belastung: Nach DIN 4421 Durchbiegung: Beschrnkt auf l/ 500 Jochuntersttzung: Im Trgerknoten Berechnungsgrundlage ist eine Dreischichtplatte 21 mm mit E=7500 N/mm2 (durchfeuchtet) und zulssiger B = 6,5 N/mm2 (durchfeuchtet).

Beispiel : Vorhandene Deckenstrke Gewhlte Schalhaut 3-S-Platte Gewhlter Quertrgerabstand Gewhlter Sttzenabstand Zulssiger Jochtrgerabstand Vorhandene Sttzenlast d = 0,25 m 3-S, 21 mm a = 0,625 m c = 1,20 m b = 2,80 m F= 28,0 kN

Ausgabe 2002

GT 24 or VT 20K girders are used individually or in combination depending on the requirements.

PERI Formwork Engineering

The supports for MULTIFLEX can take the form of individual props or falsework systems.

s Using the high-capacity GT 24 considerably reduces the number of props and makes the system more cost-effective. Particularly in combination with the fast lightweight aluminium MULTIPROPs.

MULTIPROP 350 with MULTIFLEX slab formwork.

MULTIFLEX on ST 100 stacking towers s The ideal combination for heavy slabs or higher supports. The GT 24 is used as a twin main girder to utilise the strength of the ST 100 more efficiently.

The ST 100 forkhead spindle holds two GT 24s so they cannot tilt. PERI Formwork Engineering

MULTIFLEX For any layout and any height

For substantial clear heights the ST 100 is the ideal support for MULTIFLEX, as it is easily erected and offers a high degree of safety.

MULTIFLEX can be easily adapted by changing the direction of the main girders and telescoping the secondary girders.

MULTIFLEX being used with GT 24 for a 11.60 m diameter circular tank with tapered slab.

PERI Formwork Engineering

The ST 100 stacking tower can be preassembled lying flat on the slab.

Construction of an underground car park with twin GT 24 main girders. MULTIPROPs are capable of transferring the high loads. The result is fast shuttering thanks to the small number of components.

When the striking cannot keep up with the shuttering cycles.

PERI Formwork Engineering

Formwork girders GT 24 the all-rounder

s Long service life thanks to strong practical 60 x 80 mm chords for nailing.
Length in cm (rounded) Year of manufacture Quality monitoring symbol Production date

s Long service life thanks to the patented mini-dovetail joints. The chord is ply-bonded to the entire cross section of the struts at each node to prevent it splitting.
80

Permissible shear force = 14.0 kN on struts QD Permissible shear force on ties QZ = 13.0 kN Permissible bending moment M = 7.0 kNm

s When using the 24 clawhead the reaction force of 28 kN can also be taken between the girder nodes.

s Long service life thanks to the riveted steel caps providing robust end protection.

Moment of intertia ly = 8000 cm4

Perm. reaction force A = 2 x shear force on struts = 2 x 14.0 kN = 28 kN

s Light for slabs

s Strong enough for wall formwork

s Efficient in special applications

The GT 24 being used as the girder in MULTIFLEX on ST 100, or in the UNIPORTAL tableform system.

The GT 24 makes any height up to 18 m possible in a single section.

Cost-effective special solutions no problem with the GT 24. PERI Formwork Engineering

240

VT 20K and VT 16K

PERIs VT 20K and VT 16K solid formwork girders have stood the test of time. PERI developed this type of girder with the high-grade web board right through to approval. Their fatigue strength and rigidity were put to the test in obtaining German Building Regulations Approval. Hard use on site has now confirmed the test results. PERIs solid formwork girders are designed and manufactured to achieve service lives much longer than their conventional counterparts.

The VT 20K being used as main and secondary girders. Supported by the light yet extremely strong MULTIPROP 480.

s The steel cap fixed with a steel rivet gives maximum protection against knocks and splitting at the end of the girder. It also prevents it being sawn off accidentally. s The high-density web board with high synthetic resin content makes the girder strong and rigid in use. s The 40 x 80 mm cross section of the chords of both girders prevents them tilting, and is strong enough to withstand nailing. VT 20K perm. QZ max. A perm. M Iy VT 16K perm. QZ max. A perm. M Iy
200

40

80

= 8.5 = 17 = 3.5 = 2420

kN kN kNm cm4

160

= 11.0 kN = 22 kN = 5.0 kNm = 4290 cm4

40

80

PERI Formwork Engineering

Props MULTIPROPs the aluminium prop

PERI MULTIPROPs can be used individually or combined with frames to form a table or tower. s The MULTIPROP 350 enables: only 1 prop for all heights from 1.95 m. 90% of all slabs can therefore be formed with only one type of prop.

MULTIPROP cross section

MP 625 4.30 6.25m

built-in measuring tape

MP 480 2.60 4.80m

outer tube inner tube

MP 350 1.95 3.50m

s The built-in measuring tape allows accurate pre-adjustment.

s One important factor in s The free-running nut handling is the weight. makes adjustment very easy. The MULTIPROP 350 weighs only Each MULTIPROP is continuously MP 250 18.8 kg. Even the fully extended adjustable to avoid laborious and 1.45 2.50m 480 can easily be erected by just time-consuming changing of pin one man. positions.

Every MULTIPROP comes with a built-in measuring tape.

36 mm of adjustment achieved with just one revolution (3 times as much as conventional props). PERI Formwork Engineering

10

PEP props
PEP = PERI EURO PROP

The PEP props from PERI are type tested to DIN EN 1065. Loading capacity: PEP 20 props conform to Class D of DIN EN 1065. The permissible prop load is therefore 20 kN for all extension lengths. PEP 30 props conform to Class E of DIN EN 1065. The permissible prop load is therefore 30 kN for all extension lengths. Durability The 100% hot-dip galvanizing of all surfaces at the end of the manufacturing process provides long durability. Assembly of accessories The propheads are centred on the inner and outer tubes with the same end plates. This is why the new PEP props can be simply erected upside down and easily operated.
er Hamm face sur blow

The new shape of the adjusting nut has distinctive hammer blow surfaces in the lowering direction and therefore provides the correct turning direction for lowering the loads.

PEP 30-350, 1.96 m 3.50 m in length weighs only 23 kg and carries 30.0 kN fully extended. This makes the work easy and tireless. PERI Formwork Engineering

H blo amme ws r urfa ce

11

MULTIFLEX planning Quicker and more reliable with PERI ELPOS

A layout fully shuttered with ELPOS.

s Thanks to PERI ELPOS a minimum of planning cuts equipment costs and shuttering time dramatically. s In addition to SKYDECK panel slab formwork, ELPOS can help your planning department with flexible PERI MULTIFLEX slab formwork. s ELPOS automatically works out the main and secondary girder spacings and props needed for the depth of the slab to be shuttered and the given girder lengths. s Using ELPOS, MULTIFLEX solutions can be planned just as easily as SKYDECK. s The user employs the same commands and menus. The only additional aids are for the special features of the system.

Defaults You specify the types and lengths of girder to be taken as the defaults for the MULTIFLEX slab formwork.

Structural calculations ELPOS carries out the structural calculations on MULTIFLEX for you. The main and secondary girder spacings can also be specified by the user.

12

S m ing sh is le ut es p te ti l a ri me nn ng t in an ak g r d en un e q fo m ui r in pm ien t
PERI Formwork Engineering

Choice of props ELPOS specifies which props can be used to cater for the clear height and the load.

Dimensioning The program displays individual prop and girder spacings and structure dimensions automatically.

Printouts The results achieved by ELPOS have to be seen to be believed. An exact formwork drawing for the site. An accurate parts list for the yard. And a table of the props to give an overview. PERI Formwork Engineering

13

Application Slab formwork design example

a Secon dary girde r spac a ing a a

The particular tables for the combination of girders chosen (see pages 26 to 33) are used to design the MULTIFLEX. The permissible main girder and prop spacings result from the slab thickness and the secondary girder selected, depending on the plywood.

M
b

in

gi

rd

er

a sp

cin

c c Prop spacin g c

Example: Slab depth: Clear height: Main and sec. girders: Props: Plywood size:

d = 200 mm h = 2.80 m GT 24 PEP 30-300 21 mm 3-ply, 500 x 2500 mm

Example using GT 24/GT 24 slide rule

The secondary girder spacing possible is determined using the slab depth and taking into account the formlining (sheets of 21 mm 3-ply). Pre-selection of the permissible prop spacing, main girder spacing possible and actual prop load allows the user to plan and use PERI MULTIFLEX optimally as a function of the given girder lengths, prop load capacity and structure geometry. The PERI slide rule takes account of the 300 mm spacing of the GT 24s joints so that intermediate props can be positioned without setting out.

a
0,20 Slab thickness d [m] 2 7,1 Load q [kN/ m ] Allowable spac. for main girder b [m] Actual prop load F [kN] Sec. girder spacing a [m] 0,75 0,625 0,50

Prop spacing c [m]

0,60 0,90 1,20 1,50 1,80 2,10 2,40

3,08 13,1 3,08 19,7 3,08 26,2 2,65 28 2,03 28 1,55 28 1,32 28

3,27 13,9 3,27 20,9 3,27 27,8 2,65 28 2,03 28 1,55 28 1,32 28

3,53 15,0 3,53 22,6 3,31 28 2,65 28 2,03 28 1,55 28 1,32 28

Load: According DIN 4421 Deflection: Limited to l/ 500 Main girder support: At girder nodes The calculations are based on plywood 21 mm, 3-ply, with E=7500 N/mm2 (moist) and permissible B = 6.5 N/mm2 (moist).

Edition 2002

14

PERI Formwork Engineering

Table

1. Secondary girder spacing a formlining support The secondary girder spacing is determined as a function of the slab depth and the size and type of formlining used. Sec. girder spacing: 500 mm

0,625

0,625

0,625

2. Main girder spacing b main girder support Maximum permissible span for secondary girders according to table: 3.27 m, Main girder spacing selected: 3.00 m (depending on room geometry) Main girder spacing: 3.00 m
3,00

3. Prop spacing c main girder support When using the 24 clawhead the GT 24 can be supported at any point. The maximum reaction force of 28 kN is ensured in the process. Prop spacing: 1.20 m

1,20

1,20

1,20

1,20

4. Prop load The load specified by the table is read off. It is 27.8 kN. By selecting a main girder spacing of 3.00 m there is the following prop load to be taken.

Fv = 27,8 kN x 3,00 m = 25,5 kN 3,27 m

Now select an appropriate prop (PEP, MULTIPROP). Selected: PEP 30-250 or PEP 20-300. Prop load: 25.5 kN
PERI Formwork Engineering

15

MULTIFLEX application Design example

Administration building Clear height: 3.0 m Slab depth: 300 mm

A Detail A

Formlining sheet size: 0.50 x 2.50 m Main girder length: 4.50 m Secondary girder length: 3.30 m

160

Main girder distance 2.75

150 150 120

1.05 1.40 505 625

1.05 1.40 625 625

1.05

1.05 1.40

Prop spacing for intermediate main girder Prop spacing for edge main girder

625

625

625

Secondary girder spacing

16

PERI Formwork Engineering

Section A-A AW safety handrail post AW stopend angle

300

300

3.0

PERI Formwork Engineering

17

MULTIFLEX application Erection

The PERI forkheads with self-locking coupling are inserted into the props. Forkheads without selflocking coupling must be secured with pins.

The forkhead props are stabilised with a tripod, this can only be used as an erection aid! Horizontal loads occuring during erection can only be supported at shuttering heights of up to 3 m.

2a

2b

Shuttering height > 3.0 m When using MULTIPROPs for shuttering at a height of over 3 m the props can be braced with the matching frames. 18

Alternative to Figure 2a When using PEP props or normal steel tube props for shuttering at a height of over 3.0 m diagonal bracing must be fitted.
PERI Formwork Engineering

x Pr

op sp

acing

Main gri

der spa

cing b

The forkhead props are set out. Then the main girders are lowered into the forkheads from slab level using the erection bar. The forkhead can hold one or two girders to prevent tilting.
5

The secondary girders are also installed with the erection bar from slab level.

Align the secondary girders under the formlining joints to ensure the sheets of plywood are supported safely. Lay formlining and nail down to help prevent the secondary girders tilting. Level formwork and spray surface of formlining with PERI Bio Clean.
PERI Formwork Engineering

The PERI clawhead makes nailing superfluous. Insert the clawhead with the self-locking coupling into the intermediate props and erect them at prop spacing c. With the 24 clawhead the GT 24 girder can be loaded with 28 kN even between the nodes of the girder. 19

MULTIFLEX application Striking

Striking begins with the removal of the intermediate props.

The forkhead props spindles are retracted about 40 mm.

The sheets of plywood are now removed and stacked exactly one on top of another, so that their edges can be cleaned.

The remaining secondary girders and the main girders are removed and stacked in pallets.

20

PERI Formwork Engineering

2a

Alternative to Figure 2 When using the PERI lowering head the formwork is simply lowered 40 mm using a hammer. Before being re-erected the lowering head must be pulled out again and wedged.
6

There is now sufficient space to tip the secondary girders over onto their sides and remove. Only the secondary girders at the joints between the sheets of plywood remain in place.

Remove the forkhead props and stack them in transportation pallets.

Before the first use, and for each subsequent time, spray the edges of the formlining with PERI BIO Clean. This makes erection and striking easier and protects the plywood. 21

PERI Formwork Engineering

Special applications Custom solutions with MULTIFLEX

s Early striking with temporary support Temporary props must be positioned to enable early striking. This releases the formwork for faster re-use. Early striking: First the temporary props must be positioned in the middle of the span (and other places if necessary) to satisfy the structural requirements. The actual striking operation is then carried out in the normal way. This means only a few additional props and sheets of formlining are needed. s PERI handrail holder acting as a safety system: An adjustment range of 40 cm allows the universal handrail holder to be clamped to slab formwork in exactly the same way as to members that have already been concreted. It is therefore a quick and reliable way of complying with DIN safety requirements; all that remains is to fit handrail boards and its complete. s PERI FIXPOS to support prefabricated slabs Partially prefabricated slabs are supported with PERI FIXPOS. Only main girders with props and accessories are necessary. The spacing of the main girders (support for the slabs) are mostly specified.
The PERI FIXPOS system for supporting the prefabricated slabs. Struck slab with temporary support.

THE PERI FIXPOS girder GT 24 L = 2.70 m with positioning lugs.

The PERI safety handrail holder is simply screwed tight. The positioning lugs on the GT 24 for easily positioning the props.

22

PERI Formwork Engineering

Beams
The positive connection with the UZ beam width adjustment bar allows wide spacing.

The UZ beam formwork with beam width adjustment bar for beams up to 800 mm deep. The UZ beam formwork and AW stopend angle systems allow fast and cost-effective shuttering. s UZ formwork is continuously adjustable to suit the beam cross section. s No formwork ties needed for beams up to 800 mm deep. s Girders or timbers can be used as soffit formwork. s The UZ width adjustment bars can be connected together for wide beams: Maximum beam width with one UZ 80 bar = 450 mm two UZ 80 bars = 1350 mm one UZ 129 bar = 950 mm Assuming 100 mm thick formwork.

s Extr. from PERIs book of design tables Perm. widths of load carried by UZ beam formwork [m].
Slab depth d [m] 0 0.20 0.25 0.30 0.35 Beam depth h [m] 0.30 4.00 3.65 3.45 3.30 3.20 0.40 3.50 2.85 2.70 2.40 2.15 0.50 0.60 3.00 2.50 2.25 2.00 1.75 2.75 1.80 1.65 1.50 1.35 0.70 2.25 1.35 1.25 1.15 1.05 0.80 1.65 1.05 0.95 0.90 0.80

d = Slab depth h = Beam depth

Beams up to 800 mm deep do not require any formwork ties. PERI Formwork Engineering

23

Special applications Stopends

PERIs site equipment makes erecting stopends a whole lot easier. Slabs or small overhangs are shuttered with standard system components. PERI offers two systems for slab stopends: The slab stopend bar 105 for vertical slab formwork. s For slab depths up to 500 mm s Spindles with 140 mm adjustment for exact alignment of formwork with existing concrete or formwork. The formwork bracket-2 for slab projections and slab stopends s Free-running nut to adjust for the overhang or formwork thickness. s The tapered wall supports transfer shear forces, and allow the formwork to be lowered for striking. s Slab stopends can be formed using the formwork bracket.
Adjusting spindle

HANDSET handrail post item No.: 034580

s The use of the HANDSET handrail post provides a safe lateral support.

Slab stopend bar 105

min min 0.10 0,10 m max max 0,50 0.50 m m

s Extract from PERIs book of design tables. Permissible spacings [m] of the stopend bar
The maximum deflection at the top is limited to 3 mm. Slab depth d [m] Allowing for load on the handrail post Not allowing for load on the handrail post 0.20 0.30 0.40 0.50

1.45 1.10 0.90 0.80

3.00 1.60 1.20 1.00

Small overhangs using the formwork bracket-2 Stopends flush with the wall can also be erected with formwork bracket-2.

24

PERI Formwork Engineering

The PERI AW stopend angle can be used time and again. With the AW stopend angle PERI has made it possible to erect formwork even more efficiently. Conventional slab and beam formwork solutions are a thing of the past. s The AW stopend angle is used for forming stopends and beams. s Nail-holes allow fixing in any direction, on the girder in the longitudinal direction, or on the formlining transverse to the girder.

s Extr. from the book of design tables. Perm. widths of load carried by UZ beam formwork [m].
Slab depth d [m] 0.20 0.25 0.30 0.35 0.40 Nailed to 21 mm plywood 2.50 2.50 1.50 0.90 0.60 Nailed to girder or timber 2.50 2.50 2,50 1.60 1.05 Clamped with AW clamp 2.50 2.50 2.50 2.50 2.50

The PERI stopend angle for slabs up to 400 mm thick.

The 1.40 m high AW safety handrail post provides rear protection.

The stopend angle is also nailed directly onto SKYDECK formlining in any direction required. PERI Formwork Engineering

25

MULTIFLEX GT 24 Girders as slab beams

Slab thickness [m]

0.10

0.12

0.14

0.16

0.18

0.20

Loading q* 4.5 5.0 5.5 6.1 6.6 7.1 [kN/m2] Secondary beam spacing 0.75 0.625 0.50 0.75 0.625 0.50 0.75 0.625 0.50 0.75 0.625 0.50 0.75 0.625 0.50 0.75 0.625 0.50 a [m]

0.60
Perm. span for main girder Prop spacing c [m]

0.90 1.20 1.50 1.80 2.10 2.40

3.79 10.2 3.79 15.4 3.79 20.5 3.79 25.6 3.18 28.0 2.43 28.0 2.07 28.0

4.03 10.9 4.03 16.3 4.03 21.8 4.03 27.2 3.18 28.0 2.43 28.0 2.07 28.0

4.34 11.7 4.34 17.6 4.34 23.5 4.15 28.0 3.18 28.0 2.43 28.0 2.07 28.0

3.60 10.8 3.60 16.3 3.60 21.7 3.60 27.1 2.85 28.0 2.17 28.0 1.86 28.0

3.82 11.5 3.82 17.3 3.82 23.0 3.72 28.0 2.85 28.0 2.17 28.0 1.86 28.0

4.12 12.4 4.12 18.6 4.12 24.8 3.72 28.0 2.85 28.0 2.17 28.0 1.86 28.0

3.44 11.4 3.44 17.1 3.44 22.8 3.37 28.0 2.58 28.0 1.97 28.0 1.68 28.0

3.65 12.1 3.65 18.2 3.65 24.3 3.37 28.0 2.58 28.0 1.97 28.0 1.68 28.0

3.93 13.1 3.93 19.6 3.93 26.1 3.37 28.0 2.58 28.0 1.97 28.0 1.68 28.0

3.30 12.0 3.30 18.0 3.30 24.0 3.08 28.0 2.36 28.0 1.80 28.0 1.54 28.0

3.51 12.7 3.51 19.1 3.51 25.5 3.08 28.0 2.36 28.0 1.80 28.0 1.54 28.0

3.78 13.7 3.78 20.6 3.78 27.5 3.08 28.0 2.36 28.0 1.80 28.0 1.54 28.0

3.18 12.6 3.18 18.9 3.18 25.1 2.84 28.0 2.18 28.0 1.66 28.0 1.42 28.0

3.38 13.4 3.38 20.0 3.38 26.7 2.84 28.0 2.18 28.0 1.66 28.0 1.42 28.0

3.64 14.4 3.64 21.6 3.55 28.0 2.84 28.0 2.18 28.0 1.66 28.0 1.42 28.0

3.08 13.1 3.08 19.7 3.08 26.3 2.63 28.0 2.02 28.0 1.54 28.0 1.31 28.0

3.27 13.9 3.27 20.9 3.27 27.9 2.63 28.0 2.02 28.0 1.54 28.0 1.31 28.0

3.53 15.0 3.53 22.5 3.29 28.0 2.63 28.0 2.02 28.0 1.54 28.0 1.31 28.0

Slab thickness [m]

0.22

0.24

0.26

0.28

0.30

0.35

Loading q* 7.6 8.1 8.7 9.2 9.8 11.3 [kN/m2] Secondary beam spacing 0.75 0.625 0.50 0.75 0.625 0.50 0.625 0.50 0.40 0.625 0.50 0.40 0.625 0.50 0.40 0.50 0.40 a [m]

0.60
Perm. span for main girder Prop spacing c [m]

0.90 1.20 1.50 1.80 2.10 2.40

2.99 13.7 2.99 20.5 2.99 27.4 2.45 28.0 1.88 28.0 1.43 28.0 1.22 28.0

3.18 14.5 3.18 21.8 3.06 28.0 2.45 28.0 1.88 28.0 1.43 28.0 1.22 28.0

3.42 15.7 3.42 23.5 3.06 28.0 2.45 28.0 1.88 28.0 1.43 28.0 1.22 28.0

3.09 15.1 3.09 22.7 2.87 28.0 2.29 28.0 1.76 28.0 1.34 28.0 1.15 28.0

3.33 16.3 3.33 24.4 2.87 28.0 2.29 28.0 1.76 28.0 1.34 28.0 1.15 28.0

3.59 17.5 3.59 26.3 2.87 28.0 2.29 28.0 1.76 28.0 1.34 28.0 1.15 28.0

3.02 15.7 3.02 23.5 2.69 28.0 2.16 28.0 1.65 28.0 1.26 28.0 1.08 28.0

3.25 16.9 3.25 25.3 2.69 28.0 2.16 28.0 1.65 28.0 1.26 28.0 1.08 28.0

3.50 18.2 3.50 27.3 2.69 28.0 2.16 28.0 1.65 28.0 1.26 28.0 1.08 28.0

2.95 16.2 2.95 24.3 2.54 28.0 2.03 28.0 1.56 28.0 1.19 28.0 1.02 28.0

3.17 17.5 3.17 26.2 2.54 28.0 2.03 28.0 1.56 28.0 1.19 28.0 1.02 28.0

3.42 18.8 3.39 28.0 2.54 28.0 2.03 28.0 1.56 28.0 1.19 28.0 1.02 28.0

2.88 16.9 2.88 25.3 2.39 28.0 1.91 28.0 1.47 28.0 1.12 28.0 0.96 28.0

3.11 18.2 3.11 27.3 2.39 28.0 1.91 28.0 1.47 28.0 1.12 28.0 0.96 28.0

3.35 19.6 3.19 28.0 2.39 28.0 1.91 28.0 1.47 28.0 1.12 28.0 0.96 28.0

2.96 20.1 2.75 28.0 2.06 28.0 1.65 28.0 1.26 28.0 0.96 28.0 0.82 28.0

3.19 21.6 2.75 28.0 2.06 28.0 1.65 28.0 1.26 28.0 0.96 28.0 0.82 28.0

26

PERI Formwork Engineering

MULTIFLEX GT 24 Girders as slab beams

Slab thickness [m]

0.40

0.45

0.50 16.0

0.60 19.1

0.70 22.2

0.80 25.4

0.90 28.5

1.00 31.4

Loading q* 12.9 14.4 [kN/m2] Secondary beam spacing 0.50 0.40 0.50 0.40 a [m]

0.50 0.40 0.50 0.40 0.50 0.40 0.50 0.40 0.50 0.40 0.50 0.40 2.64 25.3 1.94 28.0 1.46 28.0 1.17 28.0 0.89 28.0 0.68 28.0 0.58 28.0 2.84 27.3 1.94 28.0 1.46 28.0 1.17 28.0 0.89 28.0 0.68 28.0 0.58 28.0 2.42 27.8 1.63 28.0 1.22 28.0 0.98 28.0 0.75 28.0 0.57 28.0 0.49 28.0 2.44 28.0 1.63 28.0 1.22 28.0 0.98 28.0 0.75 28.0 0.57 28.0 0.49 28.0 2.10 28.0 1.40 28.0 1.05 28.0 0.84 28.0 0.64 28.0 0.49 28.0 0.42 28.0 2.10 28.0 1.40 28.0 1.05 28.0 0.84 28.0 0.64 28.0 0.49 28.0 0.42 28.0 1.84 28.0 1.23 28.0 0.92 28.0 0.74 28.0 0.56 28.0 0.43 28.0 0.37 28.0 1.84 28.0 1.23 28.0 0.92 28.0 0.74 28.0 0.56 28.0 0.43 28.0 0.37 28.0 1.64 28.0 1.09 28.0 0.82 28.0 0.66 28.0 0.50 28.0 0.38 28.0 0.33 28.0 1.64 28.0 1.09 28.0 0.82 28.0 0.66 28.0 0.50 28.0 0.38 28.0 0.33 28.0 1.49 28.0 0.99 28.0 0.74 28.0 0.59 28.0 0.46 28.0 0.35 28.0 0.30 28.0 1.49 28.0 0.99 28.0 0.74 28.0 0.59 28.0 0.46 28.0 0.35 28.0 0.30 28.0

0.60
Perm. span for main girder Prop spacing c [m]

0.90 1.20 1.50 1.80 2.10 2.40

2.83 21.9 2.42 28.0 1.81 28.0 1.45 28.0 1.11 28.0 0.85 28.0 0.72 28.0

3.05 23.6 2.42 28.0 1.81 28.0 1.45 28.0 1.11 28.0 0.85 28.0 0.72 28.0

2.73 23.6 2.15 28.0 1.62 28.0 1.29 28.0 0.99 28.0 0.76 28.0 0.65 28.0

2.94 25.5 2.15 28.0 1.62 28.0 1.29 28.0 0.99 28.0 0.76 28.0 0.65 28.0

* Loading to DIN 4421: Formwork load g = 0.40 kN/m2 Concrete load b = 26 kN/m3 x d (m) Live load p = 0.20 x b 1.5 p 5.0 kN/m2 Total load q=g+b+p
Secon dary b

The deflection has been limited to l/500. Main girder support at node inter-sections. Secondary girders assumed single span. Table values mean the following: 2.87 28.0 Perm. main beam spacing b [m] Existing prop load [kN]
M n ai be am sp ac i ng

eam s

pacin

Beam length 0.90m 1.20m 1.50m 1.80m 2.10m 2.40m 2.70m 3.00m 3.30m 3.60m 3.90m 4.20m 4.50m 4.80m 5.10m 5.40m 5.70m 6.00m

Item no. 075100 075120 075150 075180 075210 075240 075270 075300 075330 075360 075390 075420 075450 075480 075510 075540 075570 075600

c
Prop

c
spaci ng

PERI Formwork Engineering

27

MULTIFLEX VT 20K Girders as slab beams

Slab thickness [m]

0.10

0.12

0.14

0.16

0.18

0.20

Loading q* 4.5 5.0 5.5 6.1 6.6 7.1 [kN/m2] Secondary beam spacing 0.75 0.625 0.50 0.75 0.625 0.50 0.75 0.625 0.50 0.75 0.625 0.50 0.75 0.625 0.50 0.75 0.625 0.50 a [m]

0.60
Perm. span for main girder Prop spacing c [m]

0.90 1.20 1.50 1.80 2.10 2.40

3.10 8.4 3.10 12.6 3.10 16.8 3.10 21.0 2.50 22.0 1.91 22.0 1.54 22.0

3.30 8.9 3.30 13.4 3.30 17.8 3.26 22.0 2.50 22.0 1.91 22.0 1.54 22.0

3.55 9.6 3.55 14.4 3.55 19.2 3.26 22.0 2.50 22.0 1.91 22.0 1.54 22.0

2.94 8.9 2.94 13.3 2.94 17.7 2.92 22.0 2.24 22.0 1.71 22.0 1.38 22.0

3.13 9.4 3.13 14.1 3.13 18.8 2.92 22.0 2.24 22.0 1.71 22.0 1.38 22.0

3.37 10.1 3.37 15.2 3.37 20.3 2.92 22.0 2.24 22.0 1.71 22.0 1.38 22.0

2.81 9.3 2.81 14.0 2.81 18.7 2.65 22.0 2.03 22.0 1.55 22.0 1.25 22.0

2.99 9.9 2.99 14.9 2.99 19.9 2.65 22.0 2.03 22.0 1.55 22.0 1.25 22.0

3.22 10.7 3.22 16.0 3.22 21.4 2.65 22.0 2.03 22.0 1.55 22.0 1.25 22.0

2.70 9.8 2.70 14.7 2.70 19.6 2.42 22.0 1.86 22.0 1.42 22.0 1.15 22.0

2.87 10.4 2.87 15.6 2.87 20.9 2.42 22.0 1.86 22.0 1.42 22.0 1.15 22.0

3.09 11.2 3.09 16.9 3.03 20.6 2.42 22.0 1.86 22.0 1.42 22.0 1.15 22.0

2.60 10.3 2.60 15.4 2.60 21.8 2.23 22.0 1.71 22.0 1.30 22.0 1.06 22.0

2.77 10.9 2.77 16.4 2.77 22.0 2.23 22.0 1.71 22.0 1.30 22.0 1.06 22.0

2.98 11.8 2.98 17.7 2.79 21.5 2.23 22.0 1.71 22.0 1.30 22.0 1.06 22.0

2.52 10.7 2.52 16.1 2.52 22.0 2.07 22.0 1.59 22.0 1.21 22.0 0.98 22.0

2.68 11.4 2.68 17.1 2.58 22.0 2.07 22.0 1.59 22.0 1.21 22.0 0.98 22.0

2.89 12.3 2.89 18.4 2.58 22.0 2.07 22.0 1.59 22.0 1.21 22.0 0.98 22.0

Slab thickness [m]

0.22

0.24

0.26

0.28

0.30

0.35

Loading q* 7.6 8.1 8.7 9.2 9.8 11.3 [kN/m2] Secondary beam spacing 0.75 0.625 0.50 0.75 0.625 0.50 0.625 0.50 0.40 0.625 0.50 0.40 0.625 0.50 0.40 0.50 0.40 a [m]

0.60
Perm. span for main girder Prop spacing c [m]

0.90 1.20 1.50 1.80 2.10 2.40

2.45 11.2 2.45 16.8 2.41 22.0 1.92 22.0 1.48 22.0 1.13 22.0 0.91 22.0

2.60 11.9 2.60 17.8 2.41 22.0 1.92 22.0 1.48 22.0 1.13 22.0 0.91 22.0

2.80 12.8 2.80 19.2 2.41 22.0 1.92 22.0 1.48 22.0 1.13 22.0 0.91 22.0

2.53 12.4 2.53 18.5 2.25 22.0 1.80 22.0 1.38 22.0 1.05 22.0 0.85 22.0

2.73 13.3 2.73 20.0 2.25 22.0 1.80 22.0 1.38 22.0 1.05 22.0 0.85 22.0

2.94 14.3 2.94 21.5 2.25 22.0 1.80 22.0 1.38 22.0 1.05 22.0 0.85 22.0

2.47 12.8 2.47 19.2 2.12 22.0 1.69 22.0 1.30 22.0 0.99 22.0 0.80 22.0

2.66 13.8 2.66 20.7 2.12 22.0 1.69 22.0 1.30 22.0 0.99 22.0 0.80 22.0

2.86 14.9 2.82 22.0 2.12 22.0 1.69 22.0 1.30 22.0 0.99 22.0 0.80 22.0

2.41 13.3 2.41 19.9 2.00 22.0 1.60 22.0 1.23 22.0 0.93 22.0 0.76 22.0

2.60 14.3 2.60 21.5 2.00 22.0 1.60 22.0 1.23 22.0 0.93 22.0 0.76 22.0

2.80 15.4 2.66 22.0 2.00 22.0 1.60 22.0 1.23 22.0 0.93 22.0 0.76 22.0

2.36 13.8 2.36 20.7 1.88 22.0 1.50 22.0 1.15 22.0 0.88 22.0 0.71 22.0

2.54 14.9 2.50 22.0 1.88 22.0 1.50 22.0 1.15 22.0 0.88 22.0 0.71 22.0

2.74 16.0 2.50 22.0 1.88 22.0 1.59 22.0 1.15 22.0 0.88 22.0 0.71 22.0

2.42 16.4 2.16 22.0 1.62 22.0 1.30 22.0 1.00 22.0 0.76 22.0 0.61 22.0

2.61 17.7 2.16 22.0 1.62 22.0 1.30 22.0 1.00 22.0 0.76 22.0 0.61 22.0

28

PERI Formwork Engineering

MULTIFLEX VT 20K Girders as slab beams

Slab thickness [m]

0.40

0.45

0.50 16.0 0.50 0.40 2.16 20.7 1.53 22.0 1.15 22.0 0.92 22.0 0.70 22.0 0.54 22.0 0.43 22.0 2.29 22.0 1.53 22.0 1.15 22.0 0.92 22.0 0.70 22.0 0.54 22.0 0.43 22.0

Loading q* 12.9 14.4 [kN/m2] Secondary beam spacing 0.50 0.40 0.50 0.40 a [m]

0.60
Perm. span for main girder Prop spacing c [m]

0.90 1.20 1.50 1.80 2.10 2.40

2.32 17.9 1.90 22.0 1.42 22.0 1.14 22.0 0.87 22.0 0.67 22.0 0.54 22.0

2.50 19.3 1.90 22.0 1.42 22.0 1.14 22.0 0.87 22.0 0.67 22.0 0.54 22.0

2.23 19.3 1.69 22.0 1.27 22.0 1.02 22.0 0.78 22.0 0.59 22.0 0.48 22.0

2.40 20.8 1.69 22.0 1.27 22.0 1.02 22.0 0.78 22.0 0.59 22.0 0.48 22.0

* Loading to DIN 4421: Formwork load g = 0.40 kN/m2 Concrete load b = 26 kN/m3 x d (m) Live load p = 0.20 x b 1.5 p 5.0 kN/m2 Total load q=g+b+p

The deflection has been limited to l/500. Secondary girders assumed single span. Table values mean the following: 2.25 22.0 Perm. main beam spacing b [m] Existing prop load [kN]
sp a ci ng

Secon

dary b

eam s

pacin

Beam length 1.45m 2.15m 2.45m 2.65m 2.90m 3.30m 3.60m 3.90m 4.50m 4.90m 5.90m

Item no. 074990 074905 074910 074890 074920 074930 074940 074950 074960 074970 074980

k Yo

be

am

c c
Prop spaci ng

PERI Formwork Engineering

29

21 mm Plywood

The modulus of elasticity and the permissible tension is based on the grade and moisture content of the plywood (see page 8).

0.0068 q L4 Maximum deflection f = EI Maximum Moment M = 0.1071 q L2 (valid for at least 3 bays)

E = 3000 N/mm2 E = 4000 N/mm2 E = 5000 N/mm2 E = 6000 N/mm2 E = 7000 N/mm2 E = 8000 N/mm2

75 cm 70 cm 65 cm

60 cm

55 cm

10.7 8.0 6.4 5.3 4.6 4.0

9.3 7.0 5.6 4.7 4.0 3.5

8.0 6.0 4.8 4.0 3.4 3.0

50 cm

45 cm

40 cm
6.7 5.0 4.0 3.3 2.9 2.5

5.3 4.0 3.2 2.7 2.3 2.0

4.0 3.0 2.4 2.0 1.7 1.5

N /m

AN SP

Deflection f [mm]

N /m

/m m2

m2
35 cm

2.7 2.0 1.6 1.3 1.1 1.0

/m

m2

=
5

1.3 1.0 0.8 0.7 0.6 0.5

/m m2

m2

30 cm 25 cm

0.0 0.0 0.0 0.0 0.0 0.0

Wall formwork 0 Slab formwork 0

10

20

30

40

50

60

70

80

90

100 Concrete pressure q [kN/m2]

20 40 60 80 100 10 30 50 70 90

Slab Thickness d [cm]

30

PERI Formwork Engineering

Props MULTIPROP 250, 350, 480, 625

Permissible prop load [kN] according to type inspection

MP 250
Extend. length [m] l = 1.45 - 2.50 m Outer tube at bottom Inner tube at bottom

MP 350
l = 1.95 - 3.50 m Outer tube at bottom Inner tube at bottom

MP 480
l = 2.60 - 4.80 m Outer tube at bottom Inner tube at bottom

MP 625
l = 4.30 - 6.25 m Outer tube at bottom Inner tube at bottom

1.45 1.50 1.60 1.70 1.80 1.90 1.95 2.00 2.10 2.20 2.30 2.40 2.50 2.60 2.70 2.80 2.90 3.00 3.10 3.20 3.30 3.40 3.50 3.60 3.70 3.80 3.90 4.00 4.10 4.20 4.30 4.40 4.50 4.60 4.70 4.80 4.90 5.00 5.10 5.20 5.30 5.40 5.50 5.60 5.70 5.80 5.90 6.00 6.10 6.20 6.25

73.3 73.3 73.3 73.3 71.7 68.6 67.0 65.4 63.8 62.2 61.1 60.6 60.0

76.2 76.2 76.2 76.2 76.2 76.2 76.2 76.2 74.6 73.0 70.5 67.0 63.6

88.3 88.3 83.0 77.7 72.9 68.6 64.4 61.9 59.3 57.5 55.7 54.3 52.9 51.4 49.8 46.4 42.9

87.4 87.4 87.4 87.4 86.6 85.1 83.5 80.7 77.8 74.9 71.9 68.3 64.6 60.0 55.4 50.3 45.1

85.9 81.2 76.5 71.8 67.1 63.0 58.9 54.8 52.5 50.2 47.9 46.0 44.2 42.3 40.4 38.5 36.6 34.8 32.9 31.1 29.3 27.4 25.6

71.4 71.1 70.8 70.4 70.1 69.4 68.6 67.9 66.2 64.5 62.8 58.6 54.4 50.2 46.9 43.7 40.4 38.2 36.0 33.7 31.5 29.3 27.1

MULTIPROPs are classified according to official approval as follows: MP 250 = T 25, MP 350 = R 35, MP 480 = D 45, MP 625 = D 60. NB: We recommend using the HD spanner, Item no 022027, to release loads > 60 kN. All MULTIPROPs clamped in the table swivel head or UNIPORTAL head fitted to PERI tableforms have a permissible load of MP 350 min. 56 kN, MP 480 min. 36 kN over the entire extension range.

56.2 54.7 53.1 50.9 48.8 46.4 43.8 41.2 38.6 36.1 33.8 31.9 29.9 28.4 26.9 25.5 24.3 23.1 22.0 20.9 20.4

44.6 44.6 44.6 43.8 43.0 42.1 41.2 40.3 38.8 37.3 35.9 34.5 33.1 31.6 30.1 28.6 27.0 25.4 24.1 22.8 22.1

PERI Formwork Engineering

31

Props PEP 20
Permissible prop load [kN] according to type inspection

PEP 20 N 260*

PEP 20-300 PEP 20 N 300*

PEP 20-350 PEP 20 N 350*

PEP 20-400 PEP 20 G 410*

PEP 20-500

Extend. L = 1.51 - 2.60 m L = 1.71 - 3.00 m L = 1.96 - 3.50 m L = 2.21 - 4.00 m L = 2.71 - 5.00 m length Outer tube Inner tube Outer tube Inner tube Outer tube Inner tube Outer tube Inner tube Outer tube Inner tube [m] bottom bottom bottom bottom bottom bottom bottom bottom bottom bottom

1.60 1.70 1.80 1.90 2.00 2.10 2.20 2.30 2.40 2.50 2.60 2.70 2.80 2.90 3.00 3.10 3.20 3.30 3.40 3.50 3.60 3.70 3.80 3.90 4.00 4.10 4.20 4.30 4.40 4.50 4.60 4.70 4.80 4.90 5.00

35.0 35.0 35.0 35.0 33.5 31.9 30.9 29.8 28.6 27.1 24.8

35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 32.9 29.4

35.0 35.0 35.0 32.2 30.5 29.0 27.8 26.9 26.1 24.9 23.3 21.6 20.0

35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 31.7 28.5 25.7 23.2

35.0 35.0 35.0 35.0 35.0 35.0 33.8 32.4 31.2 30.2 29.2 27.5 25.7 24.1 22.4 20.7

35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 34.6 31.5 28.8 26.4 24.1

35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 33.6 32.5 31.2 29.6 27.8 26.1 24.5 23.0 21.6 20.1

35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 33.9 31.2 28.9 26.8 24.8 22.8

35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 34.2 32.3 30.6 28.9 27.4 26.0 24.6 23.4 22.1 20.9 20.0

35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 35.0 34.0 31.9 29.9 28.1 26.4 24.9 23.4 21.8

All PEP 20 props conform with DIN EN 1065 class D. The perm. load for the entire extension range is min. 20 kN. All PEP 20 props clamped in the table swivel head or UNIPORTAL head fitted to PERI tableforms have a permissible load of 30 kN over the entire extension range. *Application Inner Tube at bottom only possible with PERI Slab Tables or SKYDECK (Head bolted).

32

PERI Formwork Engineering

Props PEP 30
Permissible prop load [kN] according to type inspection

PEP 30-150

PEP 30-250

PEP 30-300 PEP 30 G 300*

PEP 30-350 PEP 30 G 350*

PEP 30-400

Extend. L = 0.96 - 1.50 m L = 1.46 - 2.50 m L = 1.71 - 3.00 m L = 1.96 - 3.50 m L = 2.21 - 4.00 m length Outer tube Inner tube Outer tube Inner tube Outer tube Inner tube Outer tube Inner tube Outer tube Inner tube [m] bottom bottom bottom bottom bottom bottom bottom bottom bottom bottom

1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00 2.10 2.20 2.30 2.40 2.50 2.60 2.70 2.80 2.90 3.00 3.10 3.20 3.30 3.40 3.50 3.60 3.70 3.80 3.90 4.00

35.0 35.0 35.0 34.9 34.2 33.5

35.0 35.0 35.0 35.0 35.0 35.0

40.0 40.0 40.0 40.0 38.5 36.8 35.3 34.4 33.3 32.1 30.1

40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 37.6 34.8

40.0 40.0 40.0 40.0 40.0 40.0 40.0 39.9 38.8 37.4 35.8 33.2 30.4

40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 37.2 33.8

40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 37.6 35.0 32.3 30.0

40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 37.6 34.6 31.6

40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 37.4 34.8 32.2

40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 40.0 37.0 33.9

All PEP 30 props conform with DIN EN 1065 class E. The perm. load for the entire extension range is min. 30 kN. All PEP 30 props clamped in the table swivel head or UNIPORTAL head fitted to PERI tableforms have a permissible load of 40 kN over the entire extension range. *Application Inner Tube at bottom only possible with PERI Slab Tables or SKYDECK (Head bolted).

PERI Formwork Engineering

33

GT 24 Girder
Weight kg Item no. GT 24 Girder German Approval Certificate No. Z-9.1-157 Perm. Shear Force QD Perm. Shear Force QZ Perm. Bending Moment M Moment of Inertia ly

= 14.0kN* = 13.0kN** = 7.0kNm = 8000cm4

* QD = Permiss. shear force on compression struts **QZ = Permiss. shear force on tension struts

918 1214

1510 1806

2102 2398

2694 2990

3286 3582

3878 4174

4470 4766

5062 5358

5654 5950

Nominal Lengths 0.60m RF 0.90m 1.20m To simplify handling the most 1.50m common GT 24 Girders are 1.80m colour coded for length. 2.10m 2.40m brown 2.70m grey 3.00m blue 3.30m red 3.60m green 3.90m 4.20m 4.50m 4.80m 5.10m 5.40m 5.70m 6.00m GT 24 Girder Excessive sizes 6.00-17.80m Girder Joint

4,45 5,30 7,10 8,90 10,60 12,40 14,20 15,90 17,70 19,50 21,20 23,00 24,80 26,60 28,30 30,10 31,90 33,60 35,40 5,90/m

075090 075100 075120 075150 075180 075210 075240 075270 075300 075330 075360 075390 075420 075450 075480 075510 075540 075570 075600 075000 070700

Girder end
163 296 296 = standard joint spacing

311 80

60 120 60

240

28

Girder joint
296 296

2694

GT 24 Girder 270 Fixpos Complete with: Postitioning nibs, item no. 105485 and TSS Torx 8x78, galv. item no. 103443 (each 1x). End Protection Cap GT 24, galv. For protecting timber chord of girder against being sawn off accidentally.

15,90

075290

311

0,06

070750
55 30 1 80

34

PERI Formwork Engineering

VT 20K, VT 16K Girder

Weight kg Item no. VT 20K Girder With steel end caps. German Approval Certificate No. Z-9.1-216 perm. Q = 11.0kN perm. M = 5.0kNm ly = 4290cm4
200

120

40

40

22

27 80

50

140

140

Nominal lengths 1.45m 2.15m 2.45m 2.65m 2.90m 3.30m 3.60m 3.90m 4.50m 4.90m 5.90m Excessive sizes VT 20 5.90-18.00m Cutting Cost VT Girder VT 16K Girder German Approval Certificate No. Z-9.1-216 Perm. Shear Force Q = 8.5kN Perm. Bending Moment M = 3.5kNm Moment of Inertia ly = 2420cm4

8,56 12,70 14,46 15,64 17,11 19,47 21,24 23,01 26,55 28,91 34,81 5,70/m

074990 074905 074910 074890 074920 074930 074940 074950 074960 074970 074980 074870 074900
1450 2150 2450 2650 2900 3300 3600 3900 4500 4900 5900

160

40

80

40

27 80

Nominal Lengths 2.45m 2.90m 3.30m 3.60m 3.90m 4.90m 5.90m Cutting Cost VT Girder

11,27 13,34 15,18 16,56 17,94 22,54 27,14

074610 074620 074630 074640 074650 074660 074670 074900

2450 2900

3300 3600

3900 4900

5900

PERI Formwork Engineering

35

MULTIFLEX and Accessories

Weight kg Item no. Crosshead 20/24 S, galv. With self-locking coupling. Providing stable support for single or twin GT 24 or VT 20K Girders. Girder overlap at both ends of at least 164mm in the case of the GT 24, 15cm with VT 20K. 3,24 028680 Required diameter of hole in the endplate of the prop 40mm.

Crosshead 20/24, galv Without self-locking coupling.

3,12

027890

359

201

240 210 170

Accessories: Pin 14x107, galv. Cotter Pin FS 4/1, galv. Clawhead 24 S, galv. With self-locking coupling. For supporting the GT 24 Girder at any location without nailing.

0,15 0,03 1,67

027990 018060 028890 Required diameter of hole in the endplate of the prop 40mm.

80

155 125 85

280 10 64

Clawhead 24 L, galv. Without self-locking coupling.

1,55

028880
161

Accessories: Pin 14x107, galv. Cotter Pin 4/1, galv.

With clawhead 24 S or 24 L, girders GT 24 can even be supported outside the node points with full shear force of 28kN being taken by the girder. 0,15 0,03 027990 018060

36

PERI Formwork Engineering

Weight kg Item no. Crosshead 16 S, galv. With self-locking coupling. Providing stable support for single or twin VT 16K Girders. Cantilever of Girders at each end min. 150mm. 3,00 028690 Required diameter of hole in the endplate of the prop 40mm.

Crosshead 16, galv. Without self-locking coupling.

2,88

028700

319

161

240 210 170

155

125

Accessories: Pin 14x107, galv. Cotter Pin 4/1, galv. Clawhead 16/20 S, galv. With self-locking coupling. For supporting the VT 20K or VT 16K Girder at any location without nailing.

0,15 0,03 1,06

027990 018060 028660 Required diameter of hole in the endplate of the prop 40mm.

80

85

140

Clawhead 16/20, galv. Without self-locking coupling.

0,94

028670

Accessories: Pin 14x107, galv. Cotter Pin 4/1, galv.

0,15 0,03

027990 018060

161

44

PERI Formwork Engineering

37

Weight kg Item no. Lowering Head 20/24, galv. Providing stable support for single or twin GT 24 or VT 20K Girders. Girder overlap at both ends of at least 164mm in the case of the GT 24, 15cm with VT 20K. Lowers 40mm. 5,10 028870
85 7 170

385

155

240

Accessories: Pin 14x107, galv. Cotter Pin 4/1, galv. Tension Strap 16-25, galv. For clamping 2 Girders GT 24, VT 20K or VT 16K onto Crosshead 20/24 (S) or Crosshead 16 (S).

0,15 0,03 0,57

027990 018060 028590

270

210

12

Erection Bar GT/VT, galv. For easy erection of MULTIFLEX with GT 24 or VT girders.

2,97

070740

1711 190

150

85

34

Assembly Bar 24, galv. For easy erection of MULTIFLEX with GT 24 girders.

3,09

027930

20

34 95 50 1550

38

110

PERI Formwork Engineering

Lowering 40

195

Weight kg Item no. Brace Clamp, galv. Diameter of prop 48 up to 76mm. 1,85 027940
Board max 30 min 48 max 76

186

40 400

210

Size of bracing board 30x150mm. Brace Clamp HL, galv. Diameter of prop 76 up to 89mm as well as 100 up to 120mm. 2,48 027790

max

120

min 76

100 239 40 450 210

Size of bracing board 30x150mm. Pin 14x107, galv. For fixing Crossheads as well as Clawheads etc. 0,15 027990
129 4 26 110 14

Cotter Pin 4/1, galv. For Pins to 25mm.

0,03

018060
4

Handrail Holder For easy and quick clamping to concrete slabs for supporting handrails. Adjustable from 20 up to 420mm.

9,81

035700
190 30 65

460

120

min 20 max 420

995

185

70

Board max 30

120

PERI Formwork Engineering

39

Weight kg Item no. Universal Tripod, galv. For props 48 to 120mm. Can also be used in combination with MULTIPROP Base MP 50. 9,37 028000

853

357 48 120

Only to be used as an erection device. Tripod, galv. For props 57 to 89mm. 8,98 027860
780

555

Only to be used as an erection device.

840

585

40

PERI Formwork Engineering

615

800

Weight kg Item no. Stripping Cart ASW 465 Complete with: 1 Steel traverse 140/220 ASW (1x) consisting of 3 parts 2 Folding base unit 160/190 ASW (1x) 3 Vertical frames 70/90 ASW (6x) 4 Vertical frames 70/120 ASW (6x) 5 Entry platforms 190 ASW (2x) 6 Toe-board set 70/190 ASW (1x) 7 Double handrails 190 ASW (4x) 8 Diagonal braces 210 ASW (3x) 9 Horizontal braces 190 ASW (2x) 10 Wind security clip 60 ASW (8x) 11 Ballast 10kg ASW (12x) Packed in: Ring pallet USP 104, galvanized Complete with: Lashing strap 25x5750mm (1x) Scaffold Tube steel 48.3x3.2, L = 1.0m as Ring extensions (6x) Max. platform height = 4.65m Max. working height = 6.65m Platform height alterations = 300mm 364,00 32,60 18,60 4,40 4,90 14,80 8,00 5,30 2,40 2,30 0,06 10,00 66,10 0,50 3,55 102031 102033 102025 102035 102034 102026 102030 102027 102028 102029 102037 102807 100678 100707 026411
1150
2360 1100

4 3

8 6 9 Ring pallet USP 104, galv. Observe operating instructions! Lifting device to VBG 9a Permissible load: 1200kg Stripping Cart, Alu Platform height: up to 2.00m Permissible load: 100kg/m2 77,00 035500 10 11

handrail height 980

3035

250
750

48

1800

PERI Formwork Engineering

platform height 2000

41

AW Slab Stopend Angle, UZ Beam Formwork

Weight kg Item no. AW Slab Stopend Angle Powder-coated. For forming stopends of slabs up to 400mm. Fixed to the plywood by nails. 1,68 065070
240

400

6.5 screw hole 3.5 nail hole 50 86 68 240 140 67 min 40 max 220 122

AW Bracket Slides into the AW Slab Stopend Angle. For height adjustment of side beam.

1,77

065075

40220

90

266

500

AW Handrail Post Slides into the AW Slab Stopend Angle from top. With captive locking device secured and fixed with additional nails to the plywood.

7,41

065071

762

nail holes

42

PERI Formwork Engineering

67

1439

275

132

AW Clamp 8-10 With captive Triple Wingnut. For clamping the AW Slab Stopend Angle onto timbers or Girders 80-100mm wide.

3,37

065072

Weight kg Item no. UZ Beam Bracket 40 Complete with: Captive Hook Tie and Wingnut Counterplate DW15. 12,10 065056
17 7

7 26 35

69 155 42 81 210

500

Allowable spacing see PERI tables. UZ Beam Width Adjustment Bar 80 Beam width max. 400mm. Beam width more than 400mm 2 or more of the Adjustment Bars 80 to be connected. 7,44 065057
963 700 81,5 70 50 165 14 7 420 50 165

UZ Beam Width Adjustment Bar 129 Beam width max. 900mm. Beam width more than 900mm. 2 or more of the Adjustment Bars 129 to be connected.

10,30

065065

1453 17x70=1190 81,5 70 42 50 81 310 310 310 310 210 14 7 50

UZ Beam Yoke Waler 100 For bearing one or two Girders GT 24 at each side.

9,02

065058

1000

84 120 80 180 14

440

For additional girder support. Can be mounted either on standard props or shoring systems.

40

60

0 50

PERI Formwork Engineering

43

MULTIPROP and Accessories

Weight kg Item no. MULTIPROP MP, Alu Can be used individually, as well as in combination with MULTIPROP MRK Frames tableforms or shoring towers. MULTIPROP (0.80-1.20m) MULTIPROP (1.45-2.50m) MULTIPROP (1.95-3.50m) MULTIPROP (2.60-4.80m) MULTIPROP (4.306.25m) MP 120 MP 250 MP 350 MP 480 MP 625 10,40 15,00 18,80 23,80 33,60 027288 027289 027290 027291
150 120 17 10 75

End Plate 027305

80 64

40 14

64 80 120 150

L min L max

Section

64

L min. L max. MP 120 MP 250 A MP 350 MP 480 MP 625 800 1450 1950 2600 4300 1200 2500 3500 4800 6250

A 715 1365 1865 2515 4211

B 421 1071 1571 2221 1975

17 10 75

Base MP 50 With quick action clamp coupling.

8,81

027310

150

500

12,5 80 40 200

For mounting props with 6 to 10mm thick end plates.

89

44

PERI Formwork Engineering

10

0 87

PEP Props
Weight kg Item no. Props PEP 20, galv.
6

PEP PEP PEP PEP

20-300 20-350 20-400 20-500

L = 1.71-3.00m L = 1.96-3.50m L = 2,21-4.00m L = 2.71-5.00m

15,70 19,20 22,70 30,50

103058 103059 103060 103061

End Plate
14

B
100

84

80
D2

100

120

L min L max

D1

20-300 20-350 A B D1 D2 1602 143 66.0 54.0 1852 93 71.5 59.5

20-400 20-500 2102 143 75.5 63.5 2602 143 84.0 72.0

For load capacity refer to PERI Formwork Design Tables. Props PEP 30, galv.
8

PEP PEP PEP PEP PEP

30-150 30-250 30-300 30-350 30-400

L = 0.96-1.50m L = 1.46-2.50m L = 1.71-3.00m L = 1.96-3.50m L = 2.21-4.00m

10,40 15,00 18,70 22,70 27,20

103066 103067 103062 103063 103065

End Plate
14 9

100

82

80
D2

100

120

D1 A

30-150 30-250 A B 852 93 66.0 54.0 1352 93 66.0 54.0

30-300 30-350 30-400 1602 143 71.5 59.5 1852 93 75.5 63.5 2102 143 84.0 72.0

For load capacity refer to PERI Formwork Design Tables.

D1 D2

40

40

PERI Formwork Engineering

45

1 PERI GmbH Rudolf-Diesel-Strasse 89264 Weissenhorn Phone 07309/950-0 Telefax 07309/951-0 [email protected] www.peri.de

44 21 23 19

34

36 18 40 46 11 11 6 48 17 22

PERI International
2

1 16 3 31 20 9

32 13 50 43

30

4 25 35 12

2 France PERI S.A.S. Rue Nicphore Nipce 77109 Meaux Tel.: ++ 33 / 1/ 64 35 24 40 Fax: ++ 33 / 1/ 64 35 24 50 [email protected] 3 Switzerland PERI AG Aspstrae 17 8472 Ohringen Tel.: ++ 41 / 52/ 3 20 03 03 Fax: ++ 41 / 52/ 3 35 37 61 [email protected]

7 USA PERI Formwork Systems, Inc. Suite 200 7272 Park Circle Drive Hanover, MD 21076 Tel.: ++1 /4 10/ 7 12-72 25 Fax: ++1 /4 10/ 7 12-70 80 www.peri-usa.com 8 Indonesia PT Beton Perkasa Wijaksana P.O. Box 3737 Jakarta 10210 Tel.: ++62 /21/ 5 71 26 44 Fax: ++62 /21/ 5 73 85 64 [email protected]

4 Spain PERI S.A. 9 Italy PERI S.p.A. Camino Malatones - km 0,5 Via G. Pascoli, 4 28110 Algete / Madrid 20060 Basiano (MI) Tel.: ++ 34 / 91/ 6 20 48 00 Tel.: ++39 /02/ 9 50 78-1> Fax: ++ 34 / 91/ 6 20 48 01 Fax: ++39 /02/ 95 76 19 14 [email protected] [email protected] www.peri.it 5 Belgium / Luxemburg N.V. PERI S.A. Industriepark 10 Japan Hory Corporation Nijverheidstraat 6 PB 54 11-17 Fuyuki, Kohtoh-Ku 1840 Londerzeel Ishima Bldg., 9F Tel.: ++ 32 / 52/ 31 99 31 Tokyo 135-0041 Fax: ++ 32 / 52/ 30 08 30 Tel.: ++81 /3/ 38 20 88 71 Fax: ++81 /3/ 56 21 70 24 6 Netherlands [email protected] PERI B.V. v. Leeuwenhoekweg 23 Postbus 304 11 United Kingdom/Irland PERI Ltd. 5480 AH-Schijndel Market Harborough Road Tel.: ++ 31 / 73/ 5 47 91 00 Clifton upon Dunsmore Fax: ++ 31 / 73/ 5 49 36 51 Rugby, CV23 OAN [email protected] Tel.: ++44 /17 88/ 86 16 00 Fax: ++44 /17 88/ 86 16 10 www.peri.ltd.uk

16 Austria 12 Turkey PERI Ges.mbH PERI Kalp ve skeleleri Industriegelnde 152 San. Tic. Ltd. Sti. Postfach 1 akmakl Ky Karss 3131 Getzersdorf Sanbir Bl. 4.Blge 9.Cadde No: 133 Tel.: ++43 / 27 83 / 41 19 Bykcekmece / Istanbul Fax: ++43 /27 83/ 41 19-20 Tel.: ++90 /2 12/ 8 86 74 01(02)-(09) [email protected] Fax: ++90 / 2 12 / 8 86 74 15 www.peri.com.tr 17 Czech Republic PERI spol. s r.o. 13 Hungary P.O. Box 3 PERI Kft. 252 42 Jesenice / Prahy Zdor u. 4. Tel.: ++420 /2/ 41 09 03 11 1181 Budapest Fax: ++420 /2/ 41 09 03 15 Tel.: ++36 /1/ 2-960 920 [email protected] Fax: ++36 /1 / 2-960 950 [email protected] 18 Denmark www.peri.hu PERI DANMARK A/S Fabriksparken 52 14 Malaysia 2600 Glostrup PERI-HORY MALAYSIA Tel.: ++ 45 / 43 / 45 36 27 Formwork SDN. BHD. Fax: ++ 45 / 43 / 45 36 87 Unit19-07-4, Level 7 [email protected] Damansara Heights Plaza Kelanamas, 19 Finland 19 Jalan Dungun PERI Suomi Ltd. Oy 50490 Kuala Lumpur Periistentie 61 Tel.: ++60 / 3 / 20 93 68 23 05200 Rajamki Fax: ++60 / 3 / 20 92 58 76 Tel.: ++358 /9/ 27 66 06-0 [email protected] Fax: ++358 /9/ 27 66 06-66 [email protected] 15 Singapore PERI-HORY ASIA 20 Croatia Formwork Pte. Ltd. RADIUS Oplate No. 1 Sims Lane # 06-10 II Maksimirsko naselje 1/6 Singapore 387355 10000 Zagreb Tel.: ++65 / 67 44 29 89 Tel.: ++ 385 / 1 / 2 30 42 66 Fax: ++65 / 67 44 36 93 Fax: ++ 385 / 1 / 2 30 42 66 [email protected]

21 Norway PERI NORGE AS Industriegata 11 3400 Lier Tel.: ++ 47 / 32/ 24 17 00 Fax: ++ 47 / 32/ 24 17 01 [email protected] www.peri.no 22 Poland PERI Sp.z o.o. ul. Stoeczna 62 05-860 Pochocin Tel.: ++ 48 / 22 / 7 21 74 00 Fax: ++ 48 / 22 / 7 21 74 01 [email protected] 23 Sweden PERIform SVERIGE AB Box 9073 30013 Halmstad Tel.: ++ 46 / 35 / 17 46 60 Fax: ++ 46 / 35 / 17 46 78 [email protected] 24 Korea PERI (Korea) Ltd. Korea Road Safety Authority Bldg., 9. Fl. 300-11,Yomgok-dong, Seocho-ku, Seoul 137-170 Tel.: ++ 82 / 2 / 34 60 18 00 Fax: ++ 82 / 2 / 5 57 53 82 [email protected] 25 Portugal PERIcofragens Lda. Largo da Lagoa, 14-A 2795 Linda-a-Velha Tel.: ++ 351 / 21 / 4 14 62 30 Fax: ++ 351 / 21 / 4 14 32 75

48

46 38 45

7 41 49 39 42 37 29 14 15 8 27

24 10

47 28 26

33

26 Argentina 30 Romania PERI S.A PERI Romnia SRL DN1 km 20 + 150 Ruta Nacional No. 9, km 47,5 (Panamericana Ramal Escobar) Bucuresti - Ploiesti (1625) Escobar / Prov. Bs. As. 8113 Balotesti - ILFOV Tel.: ++54 /34 88/ 42 81 00 Tel.: ++40 /21/ 2 66 24 19 Fax: ++54 /34 88/ 42 30 21 Fax: ++40 /21/ 2 66 24 20 [email protected] 31 Slovenia 27 Brazil Goran Opali s. p. PERI Formas e technologije in storitve Escoramentos Ltda. Obrena 137 Passagem Abar, 1.502 2000 Maribor 06300-000 Carapicuba Tel.: ++386 /2/ 4 21 52 40 So Paulo Fax: ++386 /2/ 4 21 52 41 Tel.: ++55 /11/ 41 86 10 41 32 Slovakia Fax: ++55 /11/ 41 86 10 41 [email protected] PERI spol. s r.o. www.peribrasil.com.br Pribylinsk 10 831 04 Bratislava 28 Chile Tel.: ++421 /2/ 4 92 09-1 11 PERI Chile Ltda. Fax: ++421 /2/ 4 92 09-1 10 C /Jos de San Martin 104 [email protected] Parque Industrial Los Libertadores Colina, Santiago de Chile 33 Australia Tel.: ++56 /2/ 4 44 60 00 PERI Australia Pty. Ltd. Fax: ++56 /2/ 4 44 60 01 116 Glendenning Road [email protected] Glendenning NSW 2761 www.peri.cl Tel.: ++61 /2/ 88 05 23 00 Fax: ++61 /2/ 96 75 72 77 29 Philippines www.periaus.com.au PERI GmbH 4-B Sycamore Center, 34 Estonia Alabang-Zapote Road B-Erivorm AS Corner Buencamino Street, Kalmistu tee 22 Alabang Muntinlupa 11216 Tallinn Metro Manila Tel.: ++372 /6/ 77 11 00 Fax: ++372 /6/ 77 11 22 Tel.: ++63 /2/ 8 09 34-01 (02) (03) Fax: ++63 /2/ 8 09 17 68 [email protected]

35 Greece PERI Hellas Ltd. Leof. Messogion 317 & Lokridos 152 31 Chalandri / Athen Tel.: ++30 / 10 / 6 72 91 21 Fax: ++30 / 10 / 6 72 91 42 [email protected] 36 Latvia VIA TEH Ltd. Matisa 49-3 1009 Riga Tel.: ++371 / 7 61 60 32 Fax: ++371 / 7 61 40 44 www.peri.lv 37 United Arab Emirates PERI (L.L.C.) Brashy Building, Office No. 212 Shk. Zayed Road P.O. Box 27933 Dubai Tel.: ++971 / 4 / 3 39 44 94 Fax: ++971 / 4 / 3 39 44 34 [email protected] 38 Canada PERI Formwork System, Inc. 63 B Progress Court Brampton, L6S 5X2 Ontario Tel.: ++1 / 9 05 / 7 92 80 00 Fax: ++1 / 9 05 / 7 92 99 42 www.peri.ca

39 Lebanon 43 Bulgaria PERI GmbH PERI BULGARIA EOOD 9 -11 Gebedje Str. Lebanon Representative Office 1612 Sofia / Bulgaria AYA Center, 7th floor Tel.: ++3 59 / 2 / 9 15 19 55 P.O. Box 90416 Fax: ++3 59 / 2 / 9 15 19 66 Antelias / Beirut [email protected] Tel.: ++ 961 / 1/ 24 33 65 www.peri.bg Fax: ++ 961 / 1 / 24 33 67 [email protected] 44 Iceland Merkur HF 40 Lithuania Skutuvogi 12a AB IMSAS 104 Reykjavik Buivydiskiu Street 22 Tel.: ++ 354 / 5 68 10 44 2010 Vilnius Fax: ++ 354 / 5 68 99 58 Tel.: ++ 370 / 2 / 42 81 00 Fax: ++ 370 / 2 / 42 81 02 45 Kazakhstan PERI Kalip ve Iskeleleri 41 Morocco Almaty Branch Office PERI S.A. Furmanova Strae, 65 Route de Rabat, km. 5 Bro 412 Corner Makataeva Piste de Beni Touzine 480004, Alma Ata Tanger Tel.: ++ 7 / 32 72 / 33 00 72 Tel.: ++ 212 / 39 31 75 48 Fax: ++ 7 / 32 72 / 33 91 16 Fax: ++ 212 / 39 31 75 49 [email protected] 42 Israel 46 Russian Federation PERI Formwork PERI GmbH Engineering Ltd. Krasnopresnenskaja 16 Moshe Dayan st. Naberezhnaja 12 P.O. Box 10202 Hotel Mezhdunarodnaja 2 Kiriat Arie Petach Tikva 49002 Nr. 1312 Tel.: ++ 972 / 3 / 9 24 93 32 123610 Moskau Fax: ++ 972 / 3 / 9 24 93 31 Tel.: ++7 / 0 95/ 2 58 23 49 [email protected] Fax: ++7/ 0 95/ 2 58 23 50 [email protected] www.peri.ru

47 South Africa PERI Wiehahn (Pty.) Ltd. P.O. Box 2668 Bellville 7535 Tel.: ++ 27 / 21 / 9 05 18 15 Fax: ++ 27 / 21 / 9 05 47 07 [email protected] www.periwiehahn.co.za 48 Ukraine TOW PERI Ukraina 23, M. Raskowoj Str. 02002 Kiew Tel.: ++ 380 / 44 / 2 38 83 57 Fax: ++ 380 / 44 / 5 17 54 88 49 Egypt PERI GmbH Egypt Branch Office 24 A, Obour Gardens, 4th floor, apt. #1 Salah Salem Street 11361 Heliopolis / Kairo Tel.: ++ 20 / 2 / 4 04 85 24/26 Fax: ++ 20 / 2 / 4 04 57 84 [email protected] 50 Serbia / Montenegro PERI GmbH Tina Ujevica 8 11060 Belgrad Tel.: ++ 381 / 11 / 12 24 20

49

The PERI Delivery Program

Panel Formwork TRIO, TRIO-L, TRIO 330 Versatile panel system HOUSING REPLIABLE DOMINO Light weight panel system HANDSET The "one man" panel system Girder Wall Formwork VARIO GT 24 Wall, column formwork RUNDFLEX and GRV Circular formwork FTF Facade formwork Shoring Systems ST 100 Stacking tower HD 200 Heavy duty prop PERI MULTIPROP The Alu prop PERI PEP Prop PEP = PERI EURO-PROP Climbing Formwork KG and CB Climbing systems ACS Self climbing formwork SKS and SSC Single sided climbing formwork Scaffolding UP T 70 / T 100 Frame scaffolding UP Rosett Modular scaffolding UP Rosett Shoring Further Systems ELPOS, Software for formwork planning Plywood Site equipment Brace frames Formwork accessories Custom forms Column Formwork RAPID Alu column formwork TRIO Column formwork QUATTRO The fast column formwork PERI SRS Circular column formwork Girder Slab Formwork MULTIFLEX Girder slab formwork UNIPORTAL / Table Modules Table form PD 8 1 system for 3 applications Platform Systems Folding Platform FB 180 Universal working and protective scaffold to DIN 4420 ASG 160 The light platform system for building trades Alu-Slab Formwork PERI SKYDECK Alu slab formwork system

PERI GmbH P.O. Box 12 64 89259 Weissenhorn Tel.: 0 73 09 / 9 50-0 Fax: 0 73 09 / 9 51 -0 [email protected] www.peri.de

pr 9.10 e 08/2002 10ho Art. Nr.: 790423