Scribd
Upload
805 views

Line Code Decoder

This document provides details about an experiment on decoding different line codes, including NRZ, RZ, AMI, and Manchester codes. The objectives are to understand the decoding theory and circuit structures for each line code. Diagrams of the decoding circuits are presented for each line code type, along with descriptions of how they recover the original data signal. The experiment procedures involve using modules to generate encoded signals, building the corresponding decoding circuits, observing the output waveforms on an oscilloscope, and recording results.

Uploaded by

Mor DepRz
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
805 views

Line Code Decoder

This document provides details about an experiment on decoding different line codes, including NRZ, RZ, AMI, and Manchester codes. The objectives are to understand the decoding theory and circuit structures for each line code. Diagrams of the decoding circuits are presented for each line code type, along with descriptions of how they recover the original data signal. The experiment procedures involve using modules to generate encoded signals, building the corresponding decoding circuits, observing the output waveforms on an oscilloscope, and recording results.

Uploaded by

Mor DepRz
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

Islamic University of Gaza Faculty of Engineering Electrical Department

Digital Communications Lab. Prepared by:

Eng. Mohammed K. Abu Foul

Experiment # (2)

Line Code Decoder


Prelab:
1. 2. 3. 4. Explain what are the advantages of line code? Explain how the AMI signal decodes? Give an actual example of the application of line code? Explain how the Manchester signal decodes?

Experiment Objectives:
1. 2. 3. 4. 5. To understand the theory and applications of line code decoder. To understand the decode theory and circuit structure of NRZ. To understand the decode theory and circuit structure of RZ. To understand the decode theory and circuit structure of AMI. To understand the decode theory and circuit structure of Manchester.

Experiment theory:
For digital transmission system, the advantages of the applications of line codes are as follow: Self-synchronization: Line code signal has the advantage of sufficient timing information, which can make the bit synchronizer catches the timing or pulses signal accurately to achieve self-synchronization. Low bit error rate: Digital signal can be recovered by comparator, which can reduce the interference of noise and bit error rate. Besides we can also add a suitable device such as match filter at the receiver to reduce the affection of intersymbol interference (ISI). Error detection capability The communication system has the ability of error detection ot correction by adding the channel encoding and decoding to the line code signal. Transparency By setting the line code signal and data protocol, we can receive any data sequence accurately. In this experiment, we will discuss the decoding signals for the different types of line code signal waveforms taken before.

1. Unipolar Nonreturn-to-zero Signal decode


Figure 2-1 shows the circuit diagram of unipolar nonreturn-to-zero (UNI-NRZ) decoder. From figure 1-1, we notice that the waveforms between UNI-NRZ signal and data
1

signal are similar to each other. Therefore, we only need to add a buffer in front of the decoder circuit, which can recover the original input data signal.

Figure 2-1 Circuit diagram of unipolar nonreturn-to-zero decoder.

2. Bipolar Nonreturn-to-zero Signal decode


Figure 2-2 shows the circuit diagram of bipolar nonreturn-to-zero (BIP-NRZ) decoder. The signal amplitude of BIP-NRZ is either positive voltage level or negative voltage level. Therefore, for decoder, we can utilize a diode to change the negative voltage level to zero voltage level, and then we can recover the original input data signal.

Figure 2-2 circuit diagram of bipolar nonreturn-to-zero decoder.

3. Unipolar Return-to-zero Signal Decode


Figure 2-3 shows the circuit diagram of uniplor return-to-zero (UNI-RZ) decoder. The output of the UNI-RZ decoder is a NOR-RS flip-flop, which is comprised by R2, R3 and two NOR gates. TP2 is the "S" terminal and TP3 is the "R" terminal. The clock signal will be inverted by a NOT gate which is comprised by the NOR gate. After that by using NOR to operate the inverted clock signal and UNI-RZ signal; and then passing through a differentiator which is comprised by C2 and R2, the output will be transformed to pulse wave which is used for "R" terminal of RS flip-flop as shown in TP1 and TP3 of figure 2-4. UNI-RZ signal will pass through a capacitor to the "S" terminal of RS flip-flop, as shown in TP2 of figure 2-4. Finally by sending both UNI-RZ and clock signals into the RS flip-flop, we can recover the original input data signal.

Figure 2-3 circuit diagram of unipolar return-to-zero decoder.

Figure 2-4 Output waveforms of unipolar return-to-zero decoder.

4. Bipolar Return-to-zero Signal Decode


As we know the difference between UNI-RZ and BIP-RZ is the UNI-RZ has only positive voltage level, nevertheless BIP-RZ has both positive and negative voltage level. Therefore, we utilize a diode to change the negative voltage level to zero voltage level as shown in figure 2-2, then we can obtain a UNI-RZ signal. After that, the UNI-RZ signal will pass through a UNI-RZ decoder circuit as shown in figure 2-3, then we can recover the original input data signal.

5. Alternate Mark Inversion Signal Decode


We know that if the negative voltage level of AMI transforms to positive voltage level, the encode waveform is exactly similar to RZ encode waveform. Therefore, the AMI decoder can be divided into two parts, which are the circuit of AMI transform to RZ and the circuit of RZ decoder. The circuit diagrams of UNI-RZ decoder and AMI transform to RZ are shown in figures 2-3 and 2-5, respectively. From figure 2-5, when the AMI signal locates at positive voltage level, the signal will pass through D2 to OUT. On the other hand, when the AMI signal locates at negative voltage level, the signal will pass through D1, which is connected to the comparator, and then pass through D3 to OUT. Therefore, we can obtain the RZ signal from AMI signal.

Figure 2-5 circuit diagram of AMI signal decoder

6. Manchester Signal Decode


By comparing the data signal, clock signal, and Manchester encode signal, we will find that we need to invert the clock signal, and then use an XOR to operate the inverted clock signal and Manchester signal. Finally, we can obtain the original data encode signal. Figure 2-6 shows the circuit diagram of Manchester decoder. From the figure, the objective of the first XOR to operate the clock signal and +5 V signal is to invert the clock signal, then the second XOR to operate the inverted clock signal and Manchester signal is to recover the original input data signal.

Figure 2-6 circuit diagram of Manchester signal decoder.

Experiment items:
Experiment 1: Unipolar and bipolar NRZ signal decode Experiment 1-1: Unipolar NRZ signal decode
1. Refer to figure DCS1-1 on ETEK DCS-6000-01 module to produce the UNI-NRZ signal. 2. To implement a unipolar NRZ decode circuit as shown in figure 2-1 or refer to figure DCS2-1 on ETEK DCS-6000-01 module. 3. Setting the frequency of function generator to 1 kHz TTL signal and connect this signal to the Data I/P of figure DCS1-1. Then connect the UNI-NRZ O/P of figure DCS1-1 to the UNI-NRZ I/P of figure DCS2-1. Next observe on the output waveform by using oscilloscope and record the measured results in table 2-1. 4. According to the input signals in table 2-1, repeat step 3 and record the measured results in table 2-1.

Experiment 1-2: Bipolar NRZ signal decode


1. Refer to figure DCS1-1 on ETEK DCS-6000-01 module to produce the BIP-NRZ signal. 2. To implement a bipolar NRZ signal decode circuit as shown in figure 2-2 or refer to figure DCS2-1 on ETEK DCS-6000-01 module. 3. Setting the frequency of function generator to 1 kHz TTL signal and connect this signal to the Data I/P of figure DCS1-1. Then connect the BIP-NRZ O/P of figure DCS1-1 to the BIP-NRZ I/P of figure DCS2-1. Next observe on the output waveform by using oscilloscope and record the measured results in table 2-2. 4. According to the input signals in table 2-2, repeat step 3 and record the measured results in table 2-2.

Experiment 2: Unipolar and bipolar RZ signal decode Experiment 2-1: Unipolar RZ signal decode
1. Refer to figure DCS1-2 on ETEK DCS-6000-01 module to produce the UNI-RZ signal. 2. To implement a unipolar RZ signal decode circuit as shown in figure 2-3 or refer to figure DCS2-2 on ETEK DCS-6000-01 module. 3. Setting the frequency of function generator to 1 kHz TTL signal and connect this signal to the CLK I/P of figure DCS1-2, as well as CLK at the left bottom and CLK I/P of figure DCS2-2. After that connect the data O/P at the left bottom to the data I/P in figure DCS1-2. Then connect the UNI-RZ O/P of figure DCS1-2 to the UNI-RZ I/P of figure DCS2-2. Next observe on the waveforms of UNI-RZ I/P, TP1, TP2, TP3, TP4 and Data O/P by using oscilloscope, finally record the measured results in table 2-3. 4. According to the input signals in table 2-3, repeat step 3 and record the measured results in table 2-3.

Experiment 2-2: Bipolar RZ signal decode


1. Refer to figure DCS1-2 on ETEK DCS-6000-01 module to produce the BIP-RZ signal. 2. To implement a transformation circuit of BIP-RZ to UNI-RZ as shown in figure 2-2 and a BIP-RZ decode circuit as shown in figure 2-3 or refer to figure DCS2-2 on ETEK DCS-6000-01 module. 3. Setting the frequency of function generator to 2 kHz TTL signal and connect this signal to the CLK I/P of figure DCS1-2 as well as CLK at the left bottom and CLK I/P of figure DCS2-2. After that connect the data O/P at the left bottom to the data I/P in figure DCS1-2. Then connect the BIP-RZ O/P of figure DCS1-2 to the BIP-RZ I/P of figure DCS2-2. Next observe on the waveforms of BIP-RZ I/P, TP1, TP2, TP3, TP4 and Data O/P by using oscilloscope, finally record the measured results in table 2-5. 4. According to the input signals in table 2-4, repeat step 3 and record the measured results in table 2-4.

Experiment 3: AMI signal decode


1. Refer to figure DCS1-3 on ETEK DCS-6000-01 module to produce the AMI signal. 2. To implement an AMI signal decode circuit as shown in figure 2-5 or refer to figure DCS2-3 on ETEK DCS-6000-01 module. 3. Setting the frequency of function generator to 2 kHz TTL signal and connect this signal to the CLK I/P of figure DCS1-3 as well as CLK at the left bottom and CLK I/P of figure DCS2-3. After that connect the data O/P at the left bottom to the data I/P in figure DCS1-3. Then connect the AMI O/P of figure DCS1-3 to the AMI I/P of figure DCS2-3. Next observe on the waveforms of AMI I/P, TP1, TP2, TP3, TP4, TP5, TP6 and Data O/P by using oscilloscope, finally record the measured results in table 1-7. 4. According to the input signals in table 2-5, repeat step 3 and record the measured results in table 2-5.

Experiment 4: Manchester signal decode


1. Refer to figure DCS1-4 on ETEK DCS-6000-01 module to produce the Manchester signal. 2. To implement Manchester signal encode circuit as shown in figure 2-6 or refer to figure DCS2-4 on ETEK DCS-6000-01 module. 3. Setting the frequency of function generator to 2 kHz TTL signal and connect this signal to the CLK I/P of figure DCS1-4 as well as CLK at the left bottom and CLK I/P of figure DCS2-4. After that connect the data O/P at the left bottom to the data I/P in figure DCS1-4. Then connect the Manchester O/P of figure DCS1-4 to the Manchester I/P of figure DCS2-4. Next observe on the waveforms of Manchester I/P, TP1 and Data O/P by using oscilloscope, finally record the measured results in table 2-6. 4. According to the input signals in table 2-6, repeat step 3 and record the measured results in table 2-6.

Measured results:
Table 2-1 measured results of UNI-NRZ signal decode Input Signal Frequencies (Data I/P) Output signal waveforms UNI-NRZ I/P Data O/P

1 kHz

2 kHz

Table 2-2 Measured results of BIP-NRZ signal decode Input Signal Frequencies (Data I/P) Output signal waveforms BIP-NRZ I/P Data O/P

1 kHz

2 kHz

Table 2-3 Measured results of UNI-RZ signal decode (fCLK = 1 kHz) Test Point Output waveforms Test Point Output waveforms

UNI-RZ I/P

TP1

TP2

TP3

TP4

Data O/P

Table 2-4 Measured results of BIP-RZ signal decode (fCLK = 2 kHz) Test Point Output waveforms Test Point Output waveforms

BIP-RZ I/P

TP1

TP2

TP3

TP4

Data O/P

Table 2-5 Measured results of AMI signal decode (fCLK = 100 Hz) Test Point Output waveforms Test Point Output waveforms

AMI I/P

TP1

TP2

TP3

TP4

TP5

TP6

Data O/P

10

Table 2-6 Measured results of Manchester signal decode Input Signal Frequencies (CLK I/P) Output signal waveforms Manchester I/P TP1 Data O/P

2 kHz

5 kHz

11

You might also like