S

Operating instructions en
9
0
0
0

4
6
6

2
9
7

(
8
9
0
8
)
Reinigen
fertig in 1:08 Std.
12 11 A B C
1 2 8 9 4 7 3 10
Reset 3 sec.
5 6
21
22
25
27
28
29
30
31
32
33
34
20
26
23
24
en Table of contents
Safety instructions . . . . . . . . . . . . . . . . . 4
Delivery . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation . . . . . . . . . . . . . . . . . . . . . . 4
In daily use . . . . . . . . . . . . . . . . . . . . . 4
Children in the household . . . . . . . . . . 4
Door lock . . . . . . . . . . . . . . . . . . . . . . 4
Damage . . . . . . . . . . . . . . . . . . . . . . . 4
Disposal . . . . . . . . . . . . . . . . . . . . . . . 5
Getting to know your appliance . . . . . . 5
Control panel . . . . . . . . . . . . . . . . . . . 5
Appliance interior . . . . . . . . . . . . . . . . 5
Selecting language . . . . . . . . . . . . . . . 6
Water softening system . . . . . . . . . . . . . 7
Setting . . . . . . . . . . . . . . . . . . . . . . . . . 7
Water hardness table . . . . . . . . . . . . . 7
Special salt . . . . . . . . . . . . . . . . . . . . . . . 8
Using special salt . . . . . . . . . . . . . . . . 8
Detergents with salt component . . . . . 8
Switching off water softening system . 8
Rinse aid . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting amount of rinse aid . . . . . . . . . 9
Switching off rinse aid refill indicator . . 9
Utensils . . . . . . . . . . . . . . . . . . . . . . . . . 10
Not suitable . . . . . . . . . . . . . . . . . . . . 10
Glass and utensil damage . . . . . . . . 10
Loading the dishwasher . . . . . . . . . . 10
Unloading the dishwasher . . . . . . . . 10
Cups and glasses . . . . . . . . . . . . . . . 10
Pans . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cutlery drawer . . . . . . . . . . . . . . . . . . 11
Folding spikes . . . . . . . . . . . . . . . . . 11
Cup support clip . . . . . . . . . . . . . . . . 11
Small accessories holder . . . . . . . . . 11
Detergent . . . . . . . . . . . . . . . . . . . . . . . . 12
Adding detergent . . . . . . . . . . . . . . . 13
Combination detergent . . . . . . . . . . . 13
Overview of programmes . . . . . . . . . . 15
Programme selection . . . . . . . . . . . . 15
Information about comparability tests 15
Additional options . . . . . . . . . . . . . . . . 16
Express Wash . . . . . . . . . . . . . . . . . . 16
Half load . . . . . . . . . . . . . . . . . . . . . . 16
Hygiene . . . . . . . . . . . . . . . . . . . . . . . 16
Intensive zone . . . . . . . . . . . . . . . . . . 16
Extra drying . . . . . . . . . . . . . . . . . . . . 16
Energy Save . . . . . . . . . . . . . . . . . . . 16
Washing the dishes . . . . . . . . . . . . . . . 17
Programme data . . . . . . . . . . . . . . . . 17
Aqua sensor . . . . . . . . . . . . . . . . . . . 17
Zeolith drying . . . . . . . . . . . . . . . . . . . 17
Switching on the appliance . . . . . . . . 17
Remaining running time display . . . . 17
Display window . . . . . . . . . . . . . . . . . 18
Timer programming . . . . . . . . . . . . . . 18
End of programme . . . . . . . . . . . . . . 18
Switching off automatically after
the end of the programme . . . . . . . . . 18
Switching off the appliance . . . . . . . . 19
Interrupting the programme . . . . . . . . 19
Terminating the programme . . . . . . . 19
Changing the programme . . . . . . . . . 19
Intensive drying . . . . . . . . . . . . . . . . . 19
Interior light . . . . . . . . . . . . . . . . . . . . 20
Maintenance and care . . . . . . . . . . . . . 20
Overall condition of the machine . . . . 20
Special salt and rinse aid . . . . . . . . . 20
Filters . . . . . . . . . . . . . . . . . . . . . . . . . 21
Spray arms . . . . . . . . . . . . . . . . . . . . 21
Waste water pump . . . . . . . . . . . . . . . 22
Troubleshooting . . . . . . . . . . . . . . . . . . 22
... when the appliance is switched on 22
... changing settings . . . . . . . . . . . . . . 22
... on the appliance . . . . . . . . . . . . . . 23
... during the wash cycle . . . . . . . . . . 23
... on the utensils . . . . . . . . . . . . . . . . 24
Customer service . . . . . . . . . . . . . . . . 25
Installation . . . . . . . . . . . . . . . . . . . . . . 25
Safety instructions . . . . . . . . . . . . . . . 25
Delivery . . . . . . . . . . . . . . . . . . . . . . . 26
Technical specifications . . . . . . . . . . . 26
Installation . . . . . . . . . . . . . . . . . . . . . 26
Waste-water connection . . . . . . . . . . . 26
Fresh water connection . . . . . . . . . . . 26
Warm water connection . . . . . . . . . . . 27
Electrical connection . . . . . . . . . . . . . 27
Removing the appliance . . . . . . . . . . 27
Transportation . . . . . . . . . . . . . . . . . . 28
Protection against frost
(Emptying the appliance) . . . . . . . . . . 28
Waste disposal . . . . . . . . . . . . . . . . . . . 28
Packaging . . . . . . . . . . . . . . . . . . . . . 28
Old appliances . . . . . . . . . . . . . . . . . 28
en
4
Delivery
Check the packaging and dishwasher
immediately for damage caused in
transit. Do not switch on a damaged
appliance, but contact your supplier.
Please dispose of the packaging
material in an environmentally friendly
manner.
Do not let children play with packaging
and its parts. There is a risk of
suffocation from collapsible boxes and
film.
Installation
Read the Installation chapter to learn
how to install and connect the appliance
correctly.
In daily use
Use the dishwasher only in the
household and only for its designed
purpose: for washing domestic dishes.
Children or people whose physical,
sensory or mental abilities prevent
them from using the appliance safely
must not use this appliance without
supervision or instruction
by a responsible person.
Do not lean or sit on the open door.
The appliance could tip.
Please note that free-standing
appliances may tip over if the baskets
are overloaded.
Do not add any solvents to the washing
chamber. Danger of explosion!
Open the door carefully when the
programme is still running. There is a
risk of hot water spraying out of the
appliance.
To prevent injuries, e. g. caused by
stumbling, open the dishwasher only
briefly in order to load and unload
the dishwasher.
Read and observe the safety
information and instructions for use on
the packaging for cleaning and rinsing
agents.
=Warning
Knives and other utensils with sharp points
must be placed horizontally in the cutlery
drawer.
Children in the household
If fitted, use the childproof lock. An
exact description can be found in the
back of the envelope.
Do not allow children to play with or
operate the appliance.
Keep children away from detergents
and rinse aid. These may cause
chemical burns in the mouth, throat
and eyes or asphyxiation.
Keep children away from open
dishwasher. The water in the rinsing
compartment is not drinking water and
could contain detergent residue.
Ensure that children do not place
fingers in the tablet collecting tray 1B.
Small fingers could become caught in
the slots.
If the appliance is installed at eye-level,
ensure when opening and closing the
door that children are not caught or
crushed between the appliance door
and the cupboard door situated below.
Childproof lock (door lock) *
The description of the childproof lock is at
the back in the envelope.
* depending on model
Damage
The appliance may be repaired and
opened up by a technician only. To do
this, disconnect the appliance from the
power supply. Pull out the mains plug
or switch off the fuse. Turn off the tap.
Safety instructions
en
5
Disposal
Make redundant appliances unusable
to prevent subsequent accidents.
Dispose of the appliance in an
environmentally friendly manner.
=Warning
Children could become locked in the
appliance (risk of suffocation) or find
themselves in other dangerous situations.
Therefore: Pull out the mains plug, sever
and dispose of the power cord. Destroy
the door lock so that the door can no
longer be closed.
Diagrams of the control panel and the
interior of the appliance can be found in
the envelope at the front.
Individual positions are referred to in the
text.
Control panel
** Number depending on model
Appliance interior
* depending on model
Getting to know your
appliance
(ON/OFF switch
0Programme buttons **
8Digital display
@Display Check water supply
HSalt refill indicator
PRinse aid refill indicator
XTimer programming display
`Timer programming
hAdditional options **
)" START button
)* Door opener
)2 Display window
1" Interior light *
1* Cutlery drawer
12 Top basket
1: Top spray arm
1B Tablet collecting tray
1J Intake opening
1R Blow opening (Zeolith container)
1Z Bottom spray arm
1b Dispenser for special salt
1j Filters
9" Bottom basket
9* Dispenser for rinse aid
92 Detergent dispenser
9: Lock for detergent dispenser
9B Rating plate
en
6
Selecting language
The language in the display window )2
can be set from p:, to p:. German
p: (Deutsch) is the factory setting.
To change the language:
Open the door.
Switch on ON/OFF switch (.
Hold down programme button # and
press START button )" until the
digital display 8 :... is indicated.
Release both buttons.
Press programme button # until the
factory set value p: is indicated on
the digital display 8.
German (Deutsch) is indicated in the
display window )2.
Press programme button 3.
Each time the button is pressed, the
set value increases by one level; when
the value of p: has been reached,
the display jumps back to p:
Press START button )".
The set value is saved.
Close the door.
Language Setting
Deutsch p:
English p:
Franais p:
Nederlands p:
Italiano p:
EAA||||/ p:
Espaol p:
Portugus p:
Svenska p:
Norsk p:
Suomi p:
Dansk p:
Trke p:
|/CC||| p:
Polski p:
e. p:
Magyar p:
Croatian p:
Slovenian p:
en
7
To ensure good washing results, the
dishwasher requires soft water, i.e.
containing low amounts of lime, otherwise
white limescale will be deposited on the
utensils and inner container.
Tap water above 7 dH (from set value
:) must be softened. The water is
softened with salt (regeneration salt) in the
water softening system of the dishwasher.
The setting and therefore the required
amount of salt depends on the degree of
hardness of your tap water (see table).
Setting
The amount of salt dispensed can be set
from : to :.
Salt is not required at the set value :.
Find out about the hardness value of
your tap water. Your water utility
company will help you with this.
Set value can be found in the water
hardness table.
Open the door.
Switch on ON/OFF switch (.
Hold down programme button # and
press START button )" until :.... is
indicated on the digital display.
Release both buttons.
The LED for button # flashes and the
digital display 8 displays the factory
setting :.
To change the setting:
Press programme button 3.
Each time the button is pressed, the
set value increases by one level; when
the value of : has been reached,
the display jumps back to : (off).
Press START button )".
The chosen setting has now been
stored.
Close the door.
Water hardness table
Water softening system
:
:
:
:
:
:
:
:
Water
hardness
value
Clarke
soft
medium
hard
08
910
1112
1315
1620
2126
2738
3962
mmol/l
01.1
1.21.4
1.51.8
1.92.1
2.22.9
3.03.7
3.85.4
5.58.9
Set value
on the
machine
Hardness
range
hard
hard
medium
medium
soft
en
8
Using special salt
Always refill with special salt immediately
before switching on the appliance. This
ensures that overrun special salt solution
is immediately washed out and does not
corrode the rinsing tank.
Open the screw-type cap of the
compartment 1b.
Fill the tank with water (only required
when switching on the appliance for
the first time).
Then add dishwasher salt (not table
salt or tablets).
The water is displaced and runs out.
As soon as the salt refill indicator H on
the fascia is lit, top up the salt.
* depending on model
Using detergents with salt
component
If combined detergents with a salt
component are used, salt can usually be
omitted up to a water hardness of 21 dH
(37 fH, 26 Clarke, 3.7 mmol/l). If the
water hardness is over 21 dH, special
salt must be used.
Switching off salt refill indicator/
water softening system
If the salt refill indicator H is impaired
(e.g. when using combined detergents
containing salt component), it can be
switched off.
Proceed as described under Adjusting
the water softening system and set the
value to :.
The water softening system and salt
refill indicator are now switched off.
=Warnings
Never fill the salt dispenser with
detergent. You will destroy the water
softening system.
To prevent corrosion, always refill with
salt immediately before switching on
the appliance.
Special salt
*
en
9
As soon as the rinse-aid refill indicator P
is lit on the fascia, there is still a rinse-aid
reserve of 1 2 rinsing processes. Refill
with rinse aid.
The rinse aid is required for stain-free
utensils and clear glasses. Use only rinse
aid for domestic dishwashers.
Combined detergents with rinse-aid
component may be used up to a water
hardness of 21 dH (37 fH, 26 Clarke,
3.7 mmol/l) only. If the water hardness is
over 21 dH, rinse aid must be used.
Open the dispenser 9* by pressing
and lifting the plate on the cover.
Carefully pour rinse aid up to the max.
mark in the filler opening.
Close cover until it clicks shut.
To prevent excessive foam formation
during the next rinse cycle, remove any
rinse aid which has run over with a
cloth.
Setting amount of rinse aid
The amount of rinse aid dispensed can be
set from : to :. This is the factory
setting :.
Do not change the amount of rinse aid
unless streaks (select lower setting) or
water stains (select higher setting) are left
on the utensils.
Open the door.
Switch on ON/OFF switch (.
Hold down programme button # and
press START button )" until :.... is
indicated on the digital display.
Release both buttons.
The LED for button # flashes and the
digital display 8 displays the factory
setting :.
Press programme button # until the
factory set value : is indicated on
the digital display 8.
To change the setting:
Press programme button 3.
Each time the button is pressed, the
set value increases by one level; when
the value of : has been reached,
the display jumps back to : (off).
Press START button )".
The set value is saved.
Close the door.
Switching off rinse aid refill
indicator
If the rinse-aid refill indicator P is
impaired (e.g. when using combined
detergents containing rinse aid
component), it can be switched off.
Proceed as described under Setting
amount of rinse aid and set the value
to :.
The rinse aid refill indicator P is now
switched off.
Rinse aid
max
en
10
Not suitable
Cutlery and utensils made of wood.
Delicate decorative glasses, craft and
antique utensils. These decors are not
dishwasher-proof.
Plastic parts not resistant to heat.
Copper and tin utensils.
Utensils which are soiled with ash, wax,
lubricating grease or ink.
Aluminium and silver parts have a
tendency to discolour and fade during the
wash cycle. Even some types of glass
(e.g. crystal glass objects) may turn cloudy
after many wash cycles.
Glass and utensil damage
Causes:
Glass type and glass production
process.
Chemical composition of the detergent.
Water temperature of the wash
programme.
Recommendation:
Use only glasses and porcelain which
the manufacturer designates as
dishwasher-proof.
Use a detergent which protects
utensils.
Take glass and cutlery out of the
dishwasher as soon as possible after
the programme ends.
Loading the dishwasher
Remove large food remnants. It is not
necessary to prerinse utensils under
running water.
Place the utensils so that
they are secure and cannot tip over.
all utensils with their openings face
down.
parts with curves or indentations
are at an angle, thereby allowing
water to drain.
does not obstruct rotation of the
two spray arms 1: and 1Z.
Very small utensils should not be washed
in the machine, as they may fall out of the
baskets.
Unloading the dishwasher
To prevent water from dripping off the
upper basket onto the utensils in the lower
basket, it is recommended to empty
the appliance from the bottom up.
Hot utensils are sensitive to shock!
Therefore, when the programme ends,
leave the utensils to cool down in the
dishwasher until they can be handled.
Cups and glasses
Top basket 12
Pans
Bottom basket 9"
Utensils
en
11
Tip
Heavily soiled utensils (pans) should
be placed in the bottom basket. The more
powerful spray jet provides a better
dishwashing result.
Tip
Other examples, such as the best way
of loading your dishwasher, can be found
on our homepage as a free download. The
corresponding Internet address can
be found on the back page of these
instructions for use.
Cutlery drawer
Arrange the cutlery in the cutlery drawer
1* as illustrated. Separately arranged
utensils are easier to remove after
washing.
The drawer can be taken out.
Folding spikes *
* depending on model
The spikes can be folded down to improve
arrangement of pans, bowls and glasses.
Cup support clip *
* depending on model
When washing cups, the cup support clip
can be folded up. The additional inclined
position reduces the accumulation
of water on the underside of the cup.
In the case of tall glasses
it is recommended to fold down
the cup support clip.
Small accessories holder *
* depending on model
Light-weight plastic accessories, e.g. cups,
lids, etc. can be held securely in the small
accessories holder.
1
2
en
12
Adjusting the height of the basket
The height of the upper utensils basket
12 can be adjusted in 3 stages to create
more space either in the upper or lower
basket.
Appliance height 81.5 cm
Appliance height 86.5 cm
Pull out the top basket 12 out.
To lower the basket, press in the left
and then the right lever on the outside
of the basket. In doing so, hold the
sides of the basket along the upper
edge to prevent it from suddenly
dropping.
To raise the basket, hold the basket on
the sides of the upper edge and lift it
up.
Before re-inserting the basket again,
ensure that it is at the same height on
both sides. Otherwise, the appliance
door cannot be closed and the upper
spray arm will not be connected to the
water circuit.
You can use tablets as well as powder
or liquid detergents for dishwashers, but
never use washing up liquid. The dosage
can be individually adjusted with powder
or a liquid detergent according
to the degree of soiling. Tablets contain
an adequately large amount of active
ingredients for all cleaning tasks. Modern,
powerful detergents predominantly
use a low-alkaline formulation with
phosphate and enzymes. Phosphates
bond the lime in the water. Enzymes break
down starch and remove protein.
Phosphate-free detergents are less
frequent. These have a slightly weaker
lime bonding capacity and require
a higher dosage. To remove coloured
stains (e.g. tea, tomato sauce), oxygen-
based bleaching agents are usually used.
Note
To ensure a good washing result, always
follow the instructions on the detergent
packaging!
If you have further questions,
we recommend that you contact
the detergent manufacturers helpline.
=Warning
Read and observe the safety information
and instructions for use on the packaging
for cleaning and rinsing agents.
Top basket Bottom
basket
Setting 1 max. 16 cm 30 cm
Setting 2 max. 18.5 cm 27.5 cm
Setting 3 max. 21 cm 25 cm
Top basket Bottom
basket
Setting 1 max. 18 cm 33 cm
Setting 2 max. 20.5 cm 30.5 cm
Setting 3 max. 23 cm 28 cm
Detergent
en
13
Adding detergent
If the detergent dispenser 92 is still
closed, press the lock 9: to open the
detergent dispenser.
Pour detergent into the dry detergent
dispenser 92 only (insert tablet flat,
not on its edge).
Dosage: see manufacturers
instructions on the packaging.
The graduated detergent
dispenser 92 helps you add the
correct amount of powder or liquid
detergent.
Usually 20 ml25 ml are adequate
for normal soiling. If using tablets, one
tablet is adequate.
Close the cover on the detergent
dispenser by sliding it up until the lock
engages without difficulty.
The detergent dispenser opens
automatically at the optimum time
depending on the programme.
The powder or liquid detergent
is distributed in the appliance and is
dissolved, the tablet falls into the tablet
collecting tray where it dissolves
in doses.
Tip
If the utensils are only lightly soiled, slightly
less than the indicated amount
of detergent is usually adequate.
Suitable detergents and care products
can be purchased online via our website
or via customer service (see back page).
Combination detergent
Apart from conventional detergents (Solo),
a number of products are offered with
additional functions. These products
contain not only the detergent but also
rinse-aid and salt replacement substances
(3in1) and, depending on the combination
(4in1, 5in1, etc.), additional components
such as glass protection or stainless steel
cleaner. Combination detergents function
only up to a specific degree of hardness
(usually 21dH). Over this limit salt and
rinse-aid must be added.
As soon as combined detergents
are used, the rinse programme is adjusted
automatically to ensure the best possible
rinsing and drying result.
=Warnings
Do not place small parts for washing in
the tablet collecting tray 1B; this
prevents the tablet from dissolving
evenly.
If you want to add more utensils after
the programme has started, do not
use the tablet collecting tray 1B
as a handle for the upper basket.
The tablet could already be there and
you will touch the partially dissolved
tablet.
15 ml
25 ml
50 ml
en
14
Notes
You will obtain optimum rinsing
and drying results by using solo
detergents and applying salt and rinse
aid separately.
If programmes are short, tablets
may not have full cleaning effect due to
different dissolving properties
and there may even be undissolved
detergent residue. It is recommended
to use washing powder for these
programmes.
The Intensive programme (on some
models) requires one tab only. When
using washing powder, you can apply
some of this cleaning agent to the
inside of the appliances door.
Even if the rinse-aid and/or salt refill
indicator is lit, the rinse programme will
run correctly with combined
detergents.
If using detergents in a water-soluble
protective cover: Take hold of the
cover with dry hands only and put
the detergent into an absolutely
dry detergent dispenser only, otherwise
the detergent may stick.
If you switch from combined
detergents to solo detergents, ensure
that the water softening system and
amount of rinse aid have been set to
the correct value.
en
15
The max. possible number of programmes is illustrated in this overview.
The corresponding programmes for your appliance can be found on the fascia.
Programme selection
You can select a suitable programme
according to the type of utensils and
degree of soiling.
Information about comparability
tests
The conditions for the comparison test
are available on request by e-mail from
[email protected].
Quote the appliance number (ENr.)
and the production date (FD) which you
can find on the rating plate 9B on the
appliance door.
Overview of programmes
Type of utensils Type of soiling Programme Possible additional
options
Programme sequence
pots and pans,
non-sensitive
utensils
and cutlery
very adhesive burned-
in or dried-on food
remnants containing
starch or protein

Auto 65 75
all
Is optimised according to
the soiling with the aid
of sensors.

Auto 45 65
mixed utensils
and cutlery
part dried, common
household food
remnants
/
Eco 50
Prerinse
Clean 50
Intermediate rinse
Final rinse 65
Dry
sensitive utensils,
cutlery,
temperature-
sensitive plastic
and glasses
slightly adhesive,
fresh food remnants

Auto 35 45
Intensive zone
Express Wash
Energy Save
Half load
Extra drying
Is optimised according to
the soiling with the aid
of sensors.
/
Quick 45
Extra drying
Clean 45
Intermediate rinse
Final rinse 55
all
cold rinsing,
intermediate cleaning
/
Prerinse
none Prerinse
en
16
* depending on model
Additional options can be set with the
buttons h.
Express Wash *
The >>Express Wash<< function can
reduce the running time by approx. 20% to
50% depending on the selected rinse
programme. The change in the running
time is indicated on the digital display 8.
To obtain optimum cleaning results at
a reduced running time, water and energy
consumption are increased.
Half load *
If you have only a few items to wash (e.g.
glasses, cups, plates), you can switch to
half load. This will save water, energy
and time. It is recommended to put a little
less detergent in the detergent dispenser
than for a full load.
Hygiene *
The temperature is increased during the
cleaning process. This increases the
hygiene status. This additional option is
ideal for cleaning e.g. chopping boards
and baby bottles.
Intensive zone *
Perfect for a mixed load. You can wash
very soiled pots and pans in the lower
basket together with normally soiled
utensils in the upper basket. The spray
pressure in the lower basket is intensified,
the rinsing temperature is increased
slightly.
Extra drying *
An increased temperature during the final
rinse and an extended drying phase
ensure that even plastic parts dry better.
There is a slight increase in the energy
consumption.
Energy Save *
Water and energy consumption can be
reduced with the Energy Save function.
The running time is extended for optimum
cleaning and drying results.
Additional options
en
17
Programme data
The programme data (consumption
values) can be found in the summary of
instructions. They refer to normal
conditions and the water hardness set
value :. Different influencing factors
such as e.g. water temperature or line
pressure may result in deviations.
Aqua sensor *
* depending on model
The Aqua sensor is an optical measuring
device (light barrier) which measures the
turbidity of the rinsing water.
The Aqua sensor is used according to the
programme. If the Aqua sensor is active,
clean rinsing water can be transferred to
the next rinse bath and water consumption
can be reduced by 36 litres. If the
turbidity is greater, the water is drained
and is replaced with fresh water. In the
automatic programmes the temperature
and running time can also be adjusted to
the degree of soiling.
Zeolith drying
The appliance features a Zeolith container
Zeolith is a mineral which can store
moisture and heat energy and release
them again.
During the washing step this heat energy
is used to dry the mineral and heat up the
rinsing water.
During the drying phase moisture from the
washing compartment is stored in the
mineral and heat energy is released. This
released heat energy is blown into the
washing compartment with dry air. This
accelerates and improves drying.
These processes therefore save a great
deal of energy.
=Warnings
Please ensure that the intake opening
1J is not obstructed and do not place
any temperature-sensitive utensils in
the lower basket at the rear right side
above the blow opening 1R.
Do not touch the blow opening 1R.
The blow opening becomes hot and,
furthermore, any damage will result in
a chargeable callout by customer
service.
Switching on the appliance
Turn on the tap fully.
Open the door.
Switch on ON/OFF switch (.
The display of the last selected
programme flashes. This programme
remains selected if no other
programme button 0 is pressed. The
expected programme duration flashes
on the digital display 8.
Press the START button )".
Close the door.
The programme starts running.
Remaining running time display
When the programme is selected, the
remaining running time of the programme
is indicated on the digital display 8.
The running time is determined during the
programme by the water temperature, the
number of utensils as well as the degree
of soiling and may vary (depending on the
selected programme).
Washing the dishes
en
18
Display window
Apart from information on the programme
sequence, the display window )2 also
indicates additional information on
e.g. spray pressure.
If you would no longer like to have this
additional information displayed, proceed
as follows.
Open the door.
Switch on ON/OFF switch (.
Hold down programme button # and
press START button )" until the
digital display 8 :... is indicated.
Release both buttons.
The LED for button # flashes and the
digital display 8 displays the factory
setting :.
Press programme button # until the
factory set value : is indicated on
the digital display 8.
To change the setting,
By pressing the 3 button, you can
switch the on board computer
(additional programme information) off
: or on :.
Press START button )".
The set value is saved.
Close the door.
Timer programming
You can delay the start of the programme
in 1 hour steps up to 24 hours.
Open the door.
Switch on ON/OFF switch (.
Press the button `+ until is
flaching in the timer programming
display X.
Press + or button until the `
displayed time corresponds with your
requirements.
Press START button )", timer
programming is activated.
To delete timer programming `,
press the + or button until is
indicated on the digital display X.
You can change your programme
selection at any time until the
programme starts.
Close the door.
End of programme
The programme has ended when the
value : is indicated on the numerical
display 8.
The end of the programme is also
indicated by an acoustic signal. This
function can be changed as follows:
Open the door.
Switch on ON/OFF switch (.
Hold down programme button # and
press START button )" until :.... is
indicated on the digital display.
Release both buttons.
The LED for button # flashes and the
digital display 8 displays the factory
setting :.
Press programme button # until the
factory set value : is indicated on
the digital display 8.
To change the setting,
Press programme button 3. Each
time the button is pressed, the set
value increases by one level; when the
value of : has been reached, the
display jumps back to : (off).
Press START button )", the set value
is saved.
Close the door.
Switching off automatically after
the end of the programme
To save energy, the dishwasher is
switched off 1 minute after the programme
ends (factory setting).
Automatic disconnection can be adjusted
from : to :.
Open the door.
Switch on ON/OFF switch (.
Hold down programme button # and
press START button )" until :... is
indicated on the digital display.
Release both buttons.
The LED for button # flashes and the
digital display 8 displays the factory
setting :.
: Appliance does not switch off
automatically
: Off after 1 min
: Off after 120 min
en
19
Press programme button # until the
factory set value : is indicated on
the digital display 8.
To change the setting:
Press programme button 3.
Each time the button is pressed, the
set value increases by one level; when
the value of : has been reached,
the display jumps back to : (off).
Press START button )".
The set value is saved.
Close the door.
Switching off the appliance
Short time after the end of the programme:
Open the door.
Switch off ON/OFF switch (.
Turn off the tap (not applicable if Aqua-
Stop fitted).
Remove the utensils when they have
cooled down.
=Warning
At the end of the programme please open
the door fully and not partially when
emptying the dishwasher. Any escaping
water vapour could damage sensitive
worktops.
Interrupting the programme
Open the door.
Switch off ON/OFF switch (.
The LEDs go out. The programme is
saved.
If the door was opened on an
appliance which has a warm water
connection or is heated, first leave the
door ajar for several minutes and then
close. Otherwise, expansion (pressure)
may cause the appliance door to
spring open or water to run out of the
appliance.
To continue the programme, switch on
the ON/OFF switch ( again.
Close the door.
Terminating the programme
(Reset)
Open the door.
Press START button )" for
approx. 3 sec.
The numerical display 8 indicates
:.
Close the door.
The programme sequence lasts
approx. 1 min. On the digital display
8 is indicated :.
Open the door.
Switch off ON/OFF switch (.
Close the door.
Changing the programme
When the START button )" has been
pressed, the programme cannot be
changed.
The only way a programme can be
changed is by Cancel programme (Reset).
Intensive drying
The final rinse uses a higher temperature
which improves the drying result. The
running time may increase slightly.
(Caution if utensils are delicate!)
Open the door.
Switch on ON/OFF switch (.
Hold down programme button # and
press START button )" until :.... is
indicated on the digital display.
Release both buttons.
The LED for button # flashes and the
digital display 8 displays the factory
setting :.
Press programme button # until the
factory set value : is indicated on
the digital display 8.
To change the setting,
Press the button 3 to switch the
Intensive drying on : or off :.
Press START button )".
The set value is saved.
Close the door.
en
20
Interior light *
The interior light 1" comes on when the
door is opened irrespective of whether the
ON/OFF switch ( is switched on or off.
When the door is closed or ajar, the light is
off.
Open the door.
Switch on ON/OFF switch (.
Hold down programme button # and
press START button )" until :.... is
indicated on the digital display.
Release both buttons.
The LED for button # flashes and the
digital display 8 displays the factory
setting :.
Press programme button # until the
factory set value : is indicated on
the digital display 8.
To change the setting,
Press the button 3 to switch the
interior light off : or on :.
Press START button )".
The set value is saved.
Close the door.
* depending on model
A regular inspection and maintenance of
your machine will help to prevent faults.
This saves time and prevents problems.
Overall condition of the machine
Check spray arm for grease and
limescale deposits.
If you find such deposits:
Fill detergent dispenser with detergent.
Start the appliance without utensils in
the programme with the highest rinsing
temperature.
Clean the appliance with detergents/
appliance cleaners which are particularly
suitable for use with dishwashers.
Regularly clean door seal with a damp
cloth.
Never use a steam cleaner to clean your
dishwasher. The manufacturer is not liable
for any consequential damage.
Regularly wipe the front of the appliance
and fascia with a damp cloth; water and a
little washing up liquid are adequate. Do
not use sponges with a rough surface or
abrasive detergents, as these could
scratch the surfaces.
Stainless steel appliances: To prevent
corrosion, avoid using sponge cloths or
wash them out thoroughly several times
before using for the first time.
=Warning
Never use other chlorinated household
detergents! Health hazard!
Special salt and rinse aid
Check the refill indicators H and
P. If required, refill salt and/or rinse
aid.
Maintenance and care
en
21
Filters
The filters 1j keep large foreign objects
in the rinsing water away from the pump.
These foreign objects may occasionally
block the filters.
The filter system consists of a coarse filter,
a flat fine filter and a microfilter.
After each washing cycle check the
filters for residue.
Unscrew filter cylinder as illustrated
and take out filter system.
Remove any residue and clean filters
under running water.
Re-install filter system in reverse
sequence and ensure that the arrow
marks are opposite each other after
closing the filter system.
Spray arms
Limescale and contaminants in the rinsing
water may block nozzles and bearings on
the spray arms 1: and 1Z.
Check outlet nozzles on the spray arms
for blockages.
Unscrew the upper spray arm 1:.
Remove the lower spray arm 1Z
upwards.
Clean spray arms under running water.
Re-engage or screw on spray arms.
1
2
en
22
Waste water pump
Large food remnants in the rinsing water
not retained by the filters may block the
waste water pump. The rinsing water is
then not pumped out and covers the filter.
In this case:
First disconnect the appliance from the
power supply.
Remove the filters 1j.
Scoop out water, use a sponge if
required.
Using a spoon, prise off pump cover
(as illustrated) until it clicks, then grip
the cover by the lug and first pull it
upwards until it resists and then pull it
out forwards.
Check inner compartment and remove
any foreign objects.
Place cover in the original position,
press down and engage.
Install filters.
The majority of faults which could occur in
daily operation can be rectified by the
user. This ensures that the appliance is
quickly available for use again. The
following overview will help you locating
the causes and gives helpful advise to
eliminate them.
=Warning
If on the digital display 8 an error code
(: to :), always disconnect the
appliance from the power supply and then
turn off the tap.
You can rectify certain faults yourself (see
following fault description), for all other
faults please contact customer service and
state the indicated fault :XX.
=Warning
Dont forget: Repairs may be carried out
by technicians only. If a component has to
be replaced, ensure that only original
spare parts are used. Improper repairs or
use of non-original spare parts may cause
considerable damage and put the user at
considerable risk.
... when the appliance is
switched on
The appliance does not start.
The mains fuse has tripped.
The appliance plug has not been
inserted.
The appliance door has not been shut
properly.
... changing settings
A setting cannot be changed, a
programme starts.
Wrong programme button pressed.
Terminate the programme (see chapter
entitled Terminating the programme
(Reset)) and start all over again.
You did not wait until programme
ended.
1
2
3
Klick
Troubleshooting
en
23
... on the appliance
Lower spray arm rotates sluggishly.
Spray arm blocked.
The door is difficult to open. *
Child-proof lock is activated. The
deactivation instructions are at the
back in the envelope.
* depending on model
Door cannot be closed.
Door lock has been activated. To reset,
close the door with greater force.
Cover on the detergent dispenser cannot
be closed.
Detergent dispenser overfilled or
mechanism blocked by sticky
detergent residue.
Detergent residue in the detergent
dispenser.
Dispenser was damp when filled.
Check water supply display @ lights
up.
Tap turned off.
Water supply interrupted.
Supply hose kinked.
Filter in the water supply blocked.
Switch off the appliance and pull
out the mains plug.
Turn off the tap.
Clean filter in the supply hose.
Reconnect power supply.
Turn on the tap.
Switch on the appliance.
Water is left in the appliance at the
end of the programme.
(:) Waste water hose is blocked
or kinked.
Filters blocked.
(:) Waste water pump blocked,
cover on the waste water pump is
not locked in position
(see Maintenance and care).
Filters blocked.
The programme has not yet ended.
Wait until programme ends (digital
display indicates :) or
implement the Reset function.
Refill indicator for salt H and/or rinse-
aid P is not lit.
Refill indicator/s switched off.
Adequate salt/rinse-aid available.
Refill indicator for special salt H is lit.
No salt.
Refill with special salt.
Sensor does not detect salt tablets.
Use different special salt.
... during the wash cycle
Unusual foam formation.
Handwash liquid in the rinse aid
dispenser.
Spilled rinse aid causes excessive
frothing, therefore please remove with
a cloth.
Appliance stops during the wash cycle.
Power supply interrupted.
Water supply interrupted.
Filling valves making striking noises
Caused by the installation of the water
line and has no effect on the function
of the machine. Remedial action is not
possible.
Knocking/rattling noise during rinsing
Spray arm is striking utensils.
Utensils not arranged correctly.
en
24
... on the utensils
Food residue on the utensils.
Utensils placed too closely together,
utensils basket overfilled.
Too little detergent.
Rinse programme too weak.
Spray arm rotation obstructed.
Spray arm nozzles blocked.
Filters blocked.
Filters incorrectly inserted.
Waste water pump blocked.
Top basket on right and left not set to
same height.
Tea or lipstick residue is not completely
removed.
The detergent has an inadequate
bleaching effect.
Too low rinsing temperature.
Too little/unsuitable detergent.
White stains on the utensils/glasses
remain milky.
If phosphate-free detergents are used with
hard tap water, white deposits may be
deposited more easily on utensils and
the container walls.
Too little/unsuitable detergent.
Too weak programme selected.
No/too little rinse aid.
No/too little special salt.
Water softening system set to the
wrong value.
Salt dispenser lock not fastened.
Contact the detergent manufacturer,
in particular if:
the utensils are very wet at the end of
the programme.
limescale forms.
Dull, discoloured glasses, film cannot be
washed off.
Unsuitable detergent.
Glasses not dishwasher-proof.
Streaks on glasses and cutlery, glasses
have metallic appearance.
Too much rinse aid.
Plastic parts discoloured.
Too little/unsuitable detergent.
Too weak programme selected.
Rust spots on the cutlery.
Cutlery not rust-resistant.
Salt content in the rinsing water too
high, as salt dispenser lock not
fastened firmly or salt was spilled while
being refilled.
Utensils not dry.
Appliance door opened too early and
utensils taken out too early.
Programme selected without drying.
Too little/unsuitable rinse aid.
Activate intensive drying.
The combined detergent used has
a poor drying performance.
Use rinse aid (see Rinse aid chapter
for setting).
en
25
If the advice given does not resolve your
problem, please contact your customer
service. Contact details can be found on
the back cover of this instruction manual
or in the enclosed customer service list.
When calling , please quote the appliance
number (1) and the production date
(FD = 2) which can be found on the rating
plate 9B on the appliance door.
Rely on the expertise of the
manufacturer. Call us to ensure that the
repair will be carried out by fully-trained
service engineers, who are equipped with
original spare parts for your appliance.
The dishwasher must be connected
correctly, otherwise it will not function
properly. The specifications for the inlet
and outlet as well as the electrical
connected loads must correspond with the
required criteria as specified in the
following paragraphs or in the installation
instructions.
Install the appliance in the correct
sequence:
Checking appliance on delivery
Installing the appliance
Waste water connection
Fresh water connection
Electrical connection
Safety instructions
Install and connect the appliance
according to the installation and
assembly instructions.
Prior to installation, disconnect the
dishwasher from the power supply.
Ensure that the protective conductor
system of the domestic supply has
been correctly installed.
The electrical connection conditions
must correspond with the
specifications on the dishwasher rating
plate 9B.
If the power cord of this appliance is
damaged, it must be replaced with a
particular power cord.
To prevent injury, the power cord may
be replaced by customer service only.
If the dishwasher is installed in a high-
sided unit, the unit must be secured
properly.
Install built-under or integratable
appliances only under continuous
worktops which have been screwed to
adjacent cupboards to ensure stability.
Do not install the appliance near heat
sources (radiators, heat storage tanks,
cookers or other appliances which
generate heat) and do not install under
a hob.
Customer service
1
2
FD
Installation
en
26
After installing the appliance, ensure
that the plug is easily accessible.
Some models:
The plastic housing on the water
connection contains an electric valve,
the connecting cables are in the supply
hose. Do not cut through this hose, do
not immerse the plastic housing in
water.
=Warning
If the appliance is not in a cavity and a
side panel is accessible, the door hinge
area must be covered at the side for
reasons of safety (risk of injury). The
covers are available as optional
accessories from customer service or
specialist outlets.
Delivery
Your dishwasher has been checked
thoroughly in the factory to ensure that it is
in working order. This may cause small
water stains. These will disappear after the
first wash cycle.
Technical specifications
Weight:
max. 60 kg
Voltage:
220240 V, 50 Hz
Connected load:
1.92.3 kW
Fuse:
10/16 A
Water pressure:
at least 0.05 MPa (0.5 bar), maximum
1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing valve
ahead.
Inlet rate:
minimum 10 litres/minute
Water temperature:
cold water; hot water max. temperature
60 C.
Installation
The required installation dimensions can
be found in the installation instructions.
Level the appliance with the aid of the
height-adjustable feet. Ensure that the
appliance is situated securely on the floor.
A built-under or integrated appliance
which is installed subsequently as a
free-standing appliance must be
secured to prevent it from overturning,
e.g. by screwing it to the wall or by
installing it under a continuous worktop
which is screwed to adjacent
cupboards.
The appliance can easily be installed in
a fitted kitchen between wooden and
plastic walls. If the plug is not freely
accessible, an allpole disconnector
with a contact opening of at least 3 mm
must be fitted on the installation side to
satisfy the relevant safety instructions.
Waste-water connection
The required work sequence can be
found in the installation instructions. If
required, fit a siphon with an drainage
connection.
Connect the waste-water hose to the
drainage connection of the siphon with
the enclosed parts.
Ensure that the drainage hose is not
kinked, crushed or twisted and that
there is no cover plate in the drainage
to prevent the waste water from flowing
out!
Fresh water connection
Connect the fresh-water connection to
the tap according to the installation
instructions with the enclosed parts.
Ensure that the fresh-water connection
is not kinked, crushed or twisted.
When replacing the appliance, always
use a new water supply hose.
Water pressure:
at least 0.05 MPa (0.5 bar), maximum
1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing valve
ahead.
en
27
Inlet rate:
minimum 10 litres/minute
Water temperature:
cold water preferred; hot water max.
temperature 60 C.
Warm water connection
The dishwasher can be connected to cold
or hot water up to max. 60 C.
Connection to hot water is recommended
if the hot water can be supplied
by energetically favourable means
and from a suitable installation, e.g. solar
heating system with circulation line.
This will save energy and time.
The hot water setting : allows you
to adjust your appliance optimally
to operation with hot water.
It is recommended to have a water
temperature (temperature of the incoming
water) of at least 40 C and no more than
60 C.
It is not recommended to connect
the appliance to hot water if the water
is supplied from an electric boiler.
Setting hot water:
Open the door.
Switch on ON/OFF switch (.
Hold down programme button # and
press START button )" until :... is
indicated on the digital display.
Release both buttons.
The LED for button # flashes and the
digital display 8 displays the factory
setting :.
Press programme button # until the
factory set value : is indicated on
the digital display 8.
To change the setting:
By pressing the 3 button, you can
switch the hot water setting off : or
on :.
Press START button )".
The set value is saved.
Close the door.
Electrical connection
Connect the appliance to an alternating
current only, ranging from 220 V to
240 V and 50 Hz via a correctly
installed socket with protective earth
conductor. See rating plate for required
fusing 9B.
The socket must be near the appliance
and freely accessible following
installation.
The connection may be modified by
technicians only.
A power cord extension may be
purchased from customer service only.
Use only a residual-current-operated
circuit-breaker which features the
symbol. Only this extension guarantees
compliance with the currently valid
regulations.
The appliance features a water
damage protection system. Please
note the system will not function
unless the power supply is connected.
Removing the appliance
Also observe the sequence of worksteps
here.
Disconnect the appliance from the
power supply.
Turn off the water supply.
Disconnect the waste water and fresh
water connections.
Loosen the fastening screws under the
worktop.
If fitted, remove the base panel.
Pull out the appliance, carefully pulling
the hose behind.
en
28
Transportation
Empty the dishwasher and secure loose
parts.
Drain the appliance according to the
following steps:
Turn on the tap.
Open the door.
Switch on ON/OFF switch (. The
displays of the last selected
programme light up.
Select programme with the highest
temperature.
The expected programme duration is
indicated on the numerical display
8.
Press START button )".
Close the door.
Programme sequence starts.
Open door after approx. 4 minutes.
Press START button )" until : is
indicated on the digital display.
Close the door.
Open door after approx. 1 minute.
The numerical display indicates :.
Switch the appliance off ( and turn
the tap off.
Transport appliance upright only.
(This prevents residual water from running
into the machine control and damaging
the programme sequence.)
Protection against frost
If the appliance is in a room where there is
a risk of frost (e.g. holiday home), empty
the appliance completely (see
Transportation).
Turn off the tap, disconnect supply
hose and drain water.
Both the packaging of new appliances and
the old appliances themselves contain
valuable raw materials and recyclable
materials.
Please dispose of the individual parts
separated according to type.
Please ask your dealer or inquire at your
local authority about current means of
disposal.
Packaging
All plastic parts of the appliance are
identified with internationally standardised
abbreviations (e.g. >PS< polystyrene).
Therefore, plastic waste can be sorted out
when the appliance is being disposed of.
Please follow the safety instructions under
Delivery.
Old appliances
Please follow the safety instructions under
Disposal of your appliance.
Waste disposal
This appliance is identified
according to the European
guideline 2002/96/EC on waste
electrical and electronic equipment
WEEE. The guideline specifies
the framework for an EU-wide valid
return and re-use of old
appliances.
)
Subject to changes.
Childproof lock (door lock) *
40 Activate the childproof lock.
41 Open the door with activated
childproof lock.
42 Deactivate childproof lock.
Always close the appliance door completely
when you leave the appliance.
This is the only way you can protect your
children from potential dangers.
Baking sheet spray head *
Large sheets or grilles and plates which have a diameter greater than 30 cm (gourmet
plates, pasta plates, dinner plates) can be cleaned with the aid of the spray head.
To do this, remove the top basket and insert the spray head as illustrated in the diagram.

* some models
Never operate the dishwasher without the top basket or baking sheet spray head!
To ensure that the spray jet can reach all parts, arrange the baking sheets as illustrated
(max. 4baking sheets and 2grilles).
If your appliance is fitted with Aqua-Stop, you can leave
your appliance unattended during operation and leave
the tap turned on afterwards. The tap should only
be turned off if you are absent from home for a prolonged
period, e.g. several weeks holiday.
A prerequisite for the warranty claim is that the appliance
has been correctly installed and connected with Aqua-Stop
according to our instructions. This also includes the correct
installation of the Aqua-Stop extension (original accessory).
Our warranty does not extend to defective feed lines
or fittings up to the Aqua-Stop connection on the tap.
This liability guarantee is valid for the service life
of the appliance.
If our Aqua-Stop system is defective and causes water
damage, we will make good the damage for private users.
To ensure water damage protection, the appliance must be
connectedto the power supply.
In addition to warranty claims against the seller based on the
purchase contract and in addition to our appliance warranty
we will pay damages under the following conditions:
1.
2.
3.
4.
AQUA-STOP guarantee
(does not apply to appliances without Aqua-Stop)
en
GB
Please find the contact data of all countries in the enclosed
customer service list.
Internet: www.siemens-home.com
Siemens-Electrogerte GmbH
Carl-Wery-Strae 34, 81739 Mnchen
To book an engineer visit and product advice
IE
0844 / 8928999
01450 2655
Calls from a BT landline will be charged at up
to 3 pence per minute.
A call set-up free of up to 6 pence may apply.
9000 466 297 en (8908)
640TV