PDF 01 Controls

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

Radio Remote Controls

K-Series Radio Remote Controls


The K-Series Radio Remote Controls are suitable for most standard overhead travelling crane applications. Phase Lock Loop (PPL) system creates distinct narrow band operating frequencies, set by software. Units are C-Tick approved by the Australian Communications and Media Authority with 70 non-licensed operating channels available on the 433-434MHz band. Units are also fully compliant with the requirements of AS1418.1-2002.

K-Series Specications Operating Range: Frequency Range: Minimum 100m 433.05 434.775MHz 70 channels with 25kHz channel spacing Emission Power: ID Code: Hamming Distance: Enclosures: Less than 10mW (adjustable, 8 levels) Over 1 million sets 4 Glass bre reinforced nylon, IP65

EMS Stop EN-ISO 13849-1 Cat. 4

Extensive Safety Features - Emergency Stop (EMS) is independently certied EN-ISO 13849-1 Category 4 Safety of Machinery: Safety-related parts of control systems - Transmitter EMS mushroom features 2 N/C switches - Receiver features dual independent CPUs (microcontrollers) which monitor each other and will execute emergency stop if one CPU fails - Receiver features dual series-connected main relays, each controlled separately by 2 different CPUs and will execute emergency stop if one main relay fails - Current sensing jammed relay detection on function relays

Transmitter Features - 2-speed buttons with distinctive position detents - Large mushroom E-Stop button (twist to reset) - Integrated internal antenna - Removable waterproof key - 3 stage low power indicator (visual and audible) - 4 standard alkaline or rechargeable AA batteries

Receiver Features - Integrated horn / alarm built into receiver - Visible external power indicator - F-Type antenna for easy antenna extension - Pre-wired with 2m loom multi-core cable - Vibration dampening rubber bushing mounts - 48 / 240 / 415V AC or 24V DC power supply

Other Features of K-Series Dual Frequencies: Adjustable Emission Power: Remote Pairing: Power On Switch / Key: Temperature Stabilization: Changing Functions: Programmable Functions: At start-up the radio control automatically selects frequency less likely to suffer interference Transmitter power can be adjusted (ie, lowered) as required for different applications and industry types (8 settings possible) New transmitters (without data le) can be paired to an existing receiver without accessing the receiver installed on the crane Non-contacting reed switch is also a removable key to disable transmitter Temperature Control Crystal Oscillator (TXCO) prevents frequency deviation due to temperature changes Pushbutton functions and system settings are changed via PC software Numerous possible non-standard functions include inching, acceleration delay, interlock delay, magnet control, etc.

K-Series Radio Remote Controls

K2 Series K2 Receiver Wiring Diagram


(1) AC-1 (2) AC-2 (3) MAIN-IN (4) MAIN-OUT (5) (6) (7) (8) (9) COM 1 UP 1S UP 2S DOWN 1S DOWN 2S
0.5A (F1) 6.3A (F2) DB1 DB2 6.3A (F3) 6.3A (F5) 6.3A (F4)

RED

COM 2 EAST 1S WEST 1S E/W 2S COM 3 SOUTH 1S NORTH 1S S/N 2S COM 4 AUX 1 AUX 2 AUX 2S COM 5 ALARM

(10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23)

8-Button, 2-Speed with E-Stop Kit Part Numbers: - SAGA1-K2 AC Supply: 48 / 240 / 415V AC - SAGA1-K2-24V DC DC Supply: 24V DC

Kit consists of: - 2 Transmitters + 1 Receiver - 2 Protective Pouches - 8 AA Alkaline Batteries - Installation Manual Dimensions Weight Power Part No.

Transmitter SAGA1-K2TX 167 48 55mm 210g 4 AA Batteries

Receiver SAGA1-K2RX 167 154 88mm 2100g AC or DC supply

K4 Series K4 Receiver Wiring Diagram


6.3A (F5)

(1) AC-1 (2) AC-2 (3) MAIN-IN (4) MAIN-OUT (5) (6) (7) (8) (9) (10) (11) (12) (13) COM 1 UP 1S UP 2S DOWN 1S DOWN 2S COM 2 EAST 1S WEST 1S E/W 2S
6.3A (F3) 0.5A (F1) 6.3A (F2)

RED

6.3A (F4)

COM 3 SOUTH 1S NORTH 1S S/N 2S COM 4 R1 R2 R1/2 2S R3 R4 R3/4 2S AUX 1 AUX 2 AUX 2S COM 5 SW A SW B

(14) (15) (16) (17) (18) (19) (20) (21) (22) (23) (24) (25) (26) (27) (28) (29) (30)

12-Button, 2-Channel, 2-Speed with E-Stop Kit Part Number: - SAGA1-K4 AC Supply: 48 / 240 / 415V AC

Kit consists of: - 2 Transmitters + 1 Receiver - 8 AA Alkaline Batteries - Installation Manual Dimensions Weight Power Part No.

Transmitter SAGA1-K4TX 274 77 42mm 385g 4 AA Batteries

Receiver SAGA1-K4RX 310 160 95mm 2900g AC supply

Protean HT Radio Remote Controls


The Protean-HT Radio Remote Control is ideal for controlling monorail hoists. Quartz crystals create distinct stable operating frequency. Unit is C-Tick approved by the Australian Communications and Media Authority with 7 non-licensed operating channels on the 433-434MHz band.

Protean HT Protean HT Wiring Diagram


0.5 A

POWER 1 POWER 2

WIRE COLOUR BLACK BROWN RED ORANGE YELLOW GREEN BLUE VIOLET GREY WHITE PINK

10 A

COM (MAIN) MAIN (COM) UP DOWN EAST WEST U/D 2S E/W 2S RO/START

4-Button, 2-Speed with E-Stop Kit Part Numbers : - 700PRO6DHT AC Supply: 24 / 48V or 240 / 415V - 700PRO6DHT-24VDC DC Supply: 12 ~ 24V DC

Kit consists of: - 2 Transmitters + 1 Receiver - 2 Protective Pouches - 4 AA Alkaline Batteries - Installation Manual Dimensions Weight Power Part No.

Transmitter 701PROL6B-TX 167 48 55mm 210g 2 AA Batteries

Receiver 701PROL6B-RX 161 74 52mm 2100g AC or DC supply

Optional Accessories

Passive Antenna

Protective Covers

www.conductix.com

Conductix-Wamper | 2009 | subject to technical modications without prior notice

Victoria (Head Ofce) 14 England Street Dandenong VIC 3175 Phone: +61 3 9706 8844 Fax: +61 3 9794 9298 New South Wales 4/77 Newton Road Wetherill Park NSW 2164 Phone: +61 2 9604 9800 Fax: +61 2 9604 9844

Queensland 2/9 Archimedes Place Murarrie QLD 4172 Phone: +61 7 3902 6000 Fax: +61 7 3902 6001 Western Australia 6/133 Kelvin Road Maddington WA 6109 Phone: +61 8 9452 1986 Fax: +61 8 9459 0503

[email protected] www.conductix.com

You might also like