0% found this document useful (0 votes)
493 views4 pages

CC Bin Activator

The Bin Activator is a device used to ensure controlled discharge of materials from silos and hoppers. It consists of a steel dish with a discharge cone and internal baffle cone attached. Vibrators are attached to induce vibration and mass flow of materials out of the silo. It is installed below the silo outlet and supported by suspension rods to isolate vibration. The Bin Activator comes in various sizes depending on the silo diameter and material properties to optimize discharge throughput.

Uploaded by

zamburitti
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
493 views4 pages

CC Bin Activator

The Bin Activator is a device used to ensure controlled discharge of materials from silos and hoppers. It consists of a steel dish with a discharge cone and internal baffle cone attached. Vibrators are attached to induce vibration and mass flow of materials out of the silo. It is installed below the silo outlet and supported by suspension rods to isolate vibration. The Bin Activator comes in various sizes depending on the silo diameter and material properties to optimize discharge throughput.

Uploaded by

zamburitti
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

The Bin Activator

the power in

powders

The Bin Activator


controlled discharge of all materials is vital to modern process systems.
The Bin Activator is extensively used to ensure t h e product is discharged efficiently and effectively in a controlled manner from a silo or hopper. Many products do not flow freely and the Bin Activator, by applied vibration, ensures that the product, whether fibrous, granular, flake or fine particulate, is discharged in a mass flow condition. A Bin Activator consists of a spun steel dish onto which a discharge cone has been bolted. Across the dish are a number of welded crossmembers that support the internal baffle cone. A vibrator motor - two on some sizes - is bolted on the outside of the dish. The degree of vibration is adjustable by means of a pair of out-of balance weights situated at each end of the motor. The whole assembly is suspended beneath the outlet of the silo on a number of suspension rods located in rubber isolation mounts, to ensure that vibration is not transmitted up the silo walls. These rods are attached to the hopper of the silo via a support ring which is welded or in some cases bolted to the hopper. A rubber sleeve secured by clamps, seals the gap between the support ring and the Bin Activator assembly. The diameter of the internal baffle cone is smaller than that of the Activator. The resultant annular gap between the two is preset to give the flow of material required.
Mass Flow

important features
Continuous yet controlled flow. Mass flow is induced. Very low maintenance. Reduces silo height, saving space and costs. Eliminates problems such as rat-holing, bridging, degradation, segregation and flushing. 30,000 sold worldwide. Wide range of sizes and applications. Carolina Conveyings expertise in handling diverse and difficult materials ensures that the correct equipment is specified for your application.

installation
The Bin Activator is a preassembled, self contained unit which can easily be fitted to new or existing silos. The support ring supplied with each Activator is welded, or bolted, to the hopper outlet. The Activator is then suspended from the ring by the suspension rods and the flexible sleeve is fitted between the ring and the Bin Activator ensuring dust-tight operation.
Hanger assembly A and B type

X Sect applicable from 6' 0'' to 12' 0'' Supporting ring assembly

X Sect applicable from 2' 0'' to 5' 0'' Baffle cone assembly Hanger assembly C type

Sleeve clamp assemblies Sleeve D Vibrator motor assembly Discharge cone assembly B C Dish assembly

PLANNING IN DETAILS FOR GENERAL GUIDANCE ONLY

size selection
The size of the Bin Activator is determined by many parameters including - the size of the silo, the material characteristics and the discharge throughput required. This can vary between 1 /3 of the diameter of the silo, for free flowing materials, to the same diameter for fibrous or flaky materials. Other parameters are also considered in order to optimize the specification. The Carolina Conveying Sales Engineer has at his disposal a computer program which will calculate the headload acting upon the Bin Activator. The Bin Activator is ideally suited to a cylindrical hopper, but it can be successfully applied to square or rectangular bins.
sizes 2 3 4 5 6 7 8 9 10 A 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0

specification
dimensions B C 2.2 2.8 3.5 4.1 4.8 5.2 5.10 6.4 6.10 1.7 2.1 2.8 3.1 3.8 4.2 4.9 5.3 5.9 D 1.5 1.10 2.2 2.4 2.5 3.0 3.7 4.5 4.8 horsepower 0.33 0.33 0.67 1.29 2.40 2.40 2x2.40 2x2.40 2x2.40

All dimensions in inches

Dimensions subject to change without notice

size range
2.0 to 10.0 diameter. Sizes above 10 can be supplied if required.

Carolina Conveying

Bin Activators SolifloTM Dischargers SolibinTM IBC Systems Bulk Bag Systems Rite RateTM Feeders Rite WeightTM Feeders DiscAirTM Aeromechanical Conveyors Blo-BinTM Dense Phase Pneumatic Conveying Blo-BendTM Ni Hard Bends Rotary Valves Side Entry Rotary Valves Blow Thru Rotary Valves Double Dumps

Specialists
in powder handling components and systems. We offer a very comprehensive range of products including Rotary Airlocks, IBC Systems, Diverter Valves, Silo Dischargers, Volumetric and Weighing Systems, Aero-mechanical Conveyors and Dense Phase Conveying Systems.

Carolina Conveying

Technology
product test facility with our complete range of machines allowing prospective clients to visit and witness trials. State of the art CAD and manufacturing facilities for material handling systems.

Carolina Conveying

Flexible Conveying Diverters Flap Conveying Diverters

Design
products are always designed to suit your particular application and requirements.

Carolina Conveying

Philosophy
our policy is to supply customers with products which conform to the highest quality specifications, are fit for their intended purpose, and offer a wide range of support services including installation, commissioning and service contracts.

Carolina Conveying Inc. P .O. Box 1208, Beaverdam Industrial Park 162 Great Oak Drive, Canton, NC 28716 Tel: (828) 235 -1005 Fax: (828) 235 1006
www.carolinaconveying.com email: [email protected]

You might also like