*********************RBS Commande*****************

rxasp:moty=rxotg;
rlcrp:cell=all;

! all PB in BSC!
! all alarm BTS in BSC!

RXTCP:moty=rxotg,cell=23642A;
rxtcp:mo=rxotg-11;
rxcdp:mo=rxotg-442;
rxasp:mo=rxotg-442;
RLCRP:CELL=23108A;

! pour avoir le tg!

! pour avoir la cell!
! check if site down!
! site down TRANS ou PWR !
!voir traffic par cell!

rxmfp:mo=rxoCF-13; !voir le code de la classe de l'alarm Excel!

rxmfp:mo=rxoTRX-49-0;
rxmfp:mo=rxoRX-69-4; !voir le code de la classe de l'alarm Excel!
rxmfp:mo=rxoTX-69-4,faulty;
rxmfp:mo=rxoTF-69;
rxmfp:mo=rxoTS-55-11-2;
rxmsp:mo=rxoCF-21,subord; !voir SI IL EST MBL!
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%% restart site%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
rxBLI:mo=rxoCF-431,subord,force;
rxese:mo=rxoCF-431,subord;
rxesi:mo=rxoCF-431,subord;
rxtei:mo=rxoCF-431;
rxble:mo=rxoCF-431,subord;
* CAS TS SYNC FAULT ( time slot)
rxasp:mo=rxotg-x
rxbli:mo=rxots-;
rxese:mo=rxots-;
rxesi:mo=rxots-;
rxtei:mo=rxots-;
rxlti:mo=rxots-;
rxble:mo=rxots-;
rxcdp:mo=rxotg-x
*****************************************************************************
* CAS LOOP TEST FAILED TSLOT
rxasp:mo=rxotg-x;
rxbli:mo=rxots-;
rxtei:mo=rxots-;
rxlti:mo=rxots-;
rxble:mo=rxots- ;
rxcdp:mo=rxots-;
*****************check DIP E1***************************
dtqsr:dip= 7RBL2,degr,unacc,sf;

!compteur DIP a zero!

rxapp:mo=rxotg-400;
!check etat dip!
radep:dev=RBLT2-1567;
ntcop:snt=ETM2-0;
dtstp:dip= 48RBL2;
dtqup:dip=3RBLT; ! BER:error rate(taux d'erreur)!
*****************************************************
rrgbp;
!check GPRS!
*****************rreset site**************************

rxbli:mo=rxocf-32,force,subord;
rxbli:mo=rxois-444;
rxese:mo=rxois-444;
rxesi:mo=rxois-444;
rxble:mo=rxoCF-32,subord;
rxble:mo=rxois-444;
-------------------------------------rxbli:mo=rxotrx-32-4,subord,force;
rxese:mo=rxotrx-32-4,subord;
rxesi:mo=rxotrx-32-4,subord;
rxble:mo=rxotrx-32-4,subord;
************************voir les routes manuly bloked***********
blorp;
! route blocked manually!
**********************************************************
*******************Halted cell***************************
rxmop:mo=rxotrx-74-8; !x,y:rxots=enused!
rlstP:cell=ALL,state=halted;
rlstc:cell=23647b,state=halted;
rlstc:cell=23647b,state=active;
allip:alcat=power;
DBTSP:TAB=SAACTIONS;
! SIZE ALTERATION !
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%CORE%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%
c7ltp:ls=all;
!voir tous les C7!
c7RSP:DEST=3-482;
!isolation de BSC (C7)!
ALLIP:alcat=apT
ALLIP:aCL=A1;
!voir all alarm BSC MSC apz/apt/apg!
ALLIP:alcat=ext;
!alarm external power!
allip:alcat=power;
! alarm power!
allip:alcat=apz;
!alarm cp rp apg!
allip:alcat=proc;
!command APZ pour bscbej1 IOG apz25!
dpwsp;
!alarm etat cp!
nsstp;
!NETWORK SYNCHRONIZATION FAULT!
aploc;
NE=MSCCNE4,NODE=A
!Lost connec Trans & core!
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
c7ltp:ls=all;
syrip:survey;
!voir les restart!
STRSP:r=BTDFNTI;
!voir alarm bloking supervision!
DBTSP:TAB=SAACTIONS;
! SIZE ALTERATION !
c7ltp:ls=ALL;
syrip:survey;
allip:ALCAT=APZ;
allip:ALCAT=POWER;
allip:ALCAT=EXT;
allip:ALCAT=APT,acl=a2;
DBTSP:tab=saactions;
DPWSP;
ALLIP;
PLLDP;
NSSTP;
GDSTP:unit=MUX3-A-325;
EXSCP:name=pctnalg_1;
stdep:dev=UPD1-6224;
EXRPP:RP=192;
mgnmp:msc=all;

Mgbsp:BSC=all;
strsp:r=IVRP1TO;
strdp:r=IVRP1TO,state=seal&libl&bloc;
aploc
exit
fchstate -q clussvc
net start clussvc
aploc;
NE=BSCANB1,NODE=A
cluster node
prcstate -l
raidutil -L logical
mml
EXIT
rrntp;

! pour voir si c un bscremot ou non (avec ou sans trc)!

APLOC;
!apres lost connection on les alarms ap file ..... and cha
rging estin......!
ALIST
! listy les alarms de la apg!
afpls -ls tqbgw
! verifier les fichies qui nont pas ete envoyer !
afpfti -f TQBGW
! si oui on va le renvoi nouveau !
exit
! sortie apg!
********************** C7 CHECK **********************
********************** STM ********************
tpstp:sdip=19E1551;
tpcop:sdip=19E1551;
dtstp:dip=1326UPD;
ntcop:snt=ET1551-24;
STDEP:DEV=1326UPD;
dtqup:dip=ALL;
strsp:r=RBEODTI;
strdp:r=RBEODTI,state=seal&bloc&libl;
DTSTP:dip=all;
**************BSC****************
C7LTP:ls=all;
c7ltp:ls=3-482;
c7ldp:ls=3-482;
c7rsp:ls=3-463;
exscp:dev= C7ST2C-97;
radep:dev=RTLTT2-1264;
ntcop:snt=ETM2-3;
dtstp:dip=26rtt2;
dtqup:dip=
**************MSC***************
C7LTP:ls=all;
c7ltp:ls=3-484;
c7ldp:ls=3-484;
c7rsp:ls=3-484;
exscp:dev=C7ST2C-18;
exdep:dev=UPD1-12272;
ntcop:snt=ET1551-9;
dtstp:dip=380UPD1;
dtqup:dip=654upd1;
******************************** check BTS ********************************
rxtcp:moty=rxoTg,cell=16763A;

rxtcp:mo=rXOTG-145;
rxcdp:mo=rxotg-315;
rxasp:mo=rxotg-112;
rxasp:moty=rxotg; !donne toute les alarm su!
rxmfp:mo=RXOCF-449;
rxmsp:mo=rxotg-197,subord;
!voir si mbl OU BLOC!
rxmop:mo=rxoCF-37;
!pour voir la cell ou se trouve le tx!
rxcap:mo=rxotg-22; !if site cascaded!
rlstp:cell=18654B;
!voir si cell halted!
rlstp:cell=ALL;
rlcrp:cell=16242a;
!voir s'il y a traffic!
rlcrp:cell=all;
rlcfp:cell=16658a;
!donne les frequence de cell!
rasap; !pour voir les devices non utilise ou les devices toujour occupe!
RXMLP:MO=RXOTG-41;
RXELP:MO=RXOTG-41;
rrntp; !check type of bsc!
******************************* check DIP *********************************
rxapp:mo=rxotg-104;
radep:dev=rblt2-1071;
ntcop:snt=eTM2-0;
dtstp:dip=55rBLT;
dtqup:dip=119rblT; !voir le taux d'erreur!
dtqsr:dip=29rbl2,degr,unacc; !pour restarter le dip!
****************************** BTS BLOCK-DEBLOCK **************************
RXBLI:MO=RXOTS-115-5-2;
RXESE:MO=RXOTG-37,SUBORD;
RLSTC:CELL=16276A,STATE=HALTED;
RXESI:MO=RXOTG-37,SUBORD;
RXBLE:MO=RXOTS-115-5-2;
RLSTC:CELL=06629C,STATE=ACTIVE;
******************** deblok bts cas loop test *******************************
RXBLI:MO=RXOTG-106,subord;
RXTEI:MO=RXOT-106;
RXLTI:MO=RXOTG-106;
RXBLE:MO=RXOTG-106;
********************************* C7 CHECK ***********************************
STM
tpstp:sdip=19E1551;
tpcop:sdip=19E1551;
dtstp:dip=1326UPD;
ntcop:snt=ET1551-24;
STDEP:DEV=1326UPD;
dtqup:dip=ALL;
strsp:r=BADR1TI;
strdp:r=bHASS1o,state=seal&bloc&libl;
DTSTP:dip=all;
*************** check route racimo/spanish/vms ***********************
strsp:r=ivrp1to; !Racimo MSCMUS1!
strsp:r=ptfk1to&ptfk2to&ptfk3to;
strsp:r=vms1t1o&vms02to;
strsp:r=PMHI2TI&PMHI2TO;
**************BSC****************
C7LTP:ls=all;

c7ltp:ls=3-463;
c7ldp:ls=3-463;
c7rsp:ls=3-463;
exscp:dev= C7ST2C-19;
radep:dev=RTLTT2-1264;
ntcop:snt=ETM2-3;
dtstp:dip=26rtt2;
dtqup:dip=
**************MSC***************
C7LTP:ls=all;
c7ltp:ls=3-600;
c7ldp:ls=2-5034;
c7rsp:ls=3-110;
exscp:dev=C7ST2C-103;
exdep:dev=UPD-1505;
ntcop:snt=UPET-47;
dtstp:dip=47UPDP;
dtqup:dip=654upd1;
DTDIP:dip=315mal1; ! pour trouver stm a partir du dip!
exdrp:dev=c7sth-1&&-31; !pour voir le rp qui connect ces mic!
C7RADEP;
!voir les alternances des routes!
c7ltp:dest=2-35;
! voir les route!
stdep:dev=c7sth-0;
nsstp;
!pour voir network suncronisation!
tpstp:sdip=0e1551;
!pour voir si ms bloc manualy!
strdp:r=BSALHTO;
!pour voir le dev a partir de la route!
strdp:r=CNCP3TO,state=seal&libl&bloc; !voir les device de bloking supervision!
strsp:r=CNCP3TO;
!voir l'etat de la route OU BIEN TOUT LES ROUTES
!
blorp;
!voir les routes qui sont bloquie!
mgbsp:bsc=all;
!voir les BSC ratachees!
mgnmp:msc=all;
!voir les BSC ratachees!
ne=BSCMLA1,node=a;
!ecrit ga dans network element pour checker si on a
pb trans ou pb dans APG!
dpwsp;
!cp stat!
exscp:name=name; !semipermanent connection data!
****************** pour definir le correspondance bsc-bsc **************
RACIP:DEV=RTLTT2-63;
on prend atercic ,on lance la CMD RACIP dans l'autre BSC
RACIP:ATERCIC=63;
GdSTP;
nsstp;
****************** pour definir le correspondance Msc-Msc **************
exdep:dev=upd1-xxxx;
! on prend le cic "misc1"
vers l'autre MSC on lance la commande
exdep:r=xxx,misc1=x;
*************************** check alarm APZ & APT ***************************
c7ltp:ls=aLl;
allip;
allip:alcat=APz;
allip:alcat=APT,acl=A3;
allip:alcat=poweR;
allip:alcat=ext;
allip:prca=43;
syrip:survey;
!voir historique des alarm!
syrip:log;

PLLDP;
RRGBP;
SYELP;
!soft error !
AFTSP:TEST=110,sae=all;
strdp:r=ALL,state=abl;
!bloking supervisionAPZ!
dbtsp:tab=saactions;
!size alteration!
SAOCP;
!SIZE ALTERATION CONTROL!
saaep:sae=700,block=all;
saaii:sae=36,ni=1680;
!size alteration increas!
saadi;
!(for size alteration decrease /not common/!
tpstp:sdip=20e1551; !pour voir ms alarm:NETWORK PROTECTION UNPROTECTED MODE!
ntdcp:snt=20e1551-9,subsnt=1;!pour voir ms alarm:NETWORK PROTECTION UNPROTECTED
MODE!
mml
rlvap;
!CELL SEIZURE SUPERVISION OF LOGICAL CHANNELS!
rlvar:CHTYPE=TCH;
hgsdc;
gdstp; !voir groupe switc!
****************** desactivation c7 ****************************
C7LAI:LS=2-206;
C7LAE:ls=3-206;
***************** !SYNCHRONOUS DIGITAL PATH QUALITY SUPERVISION! **********
tpqsr:sdip=2ETM2,unacc,degr; !reset!
TPSTP:SDIP=2Etm2;
tpcop:sdip=2Etm2;
************************ cas lost connection APG *****************************
AplOC;
ipconfig
alist
DPWSP;
MML
prcstate -l
cluster group
CLUSTER NODE
HOSTNAME
PRCSTATE
NET START ACS_PRC_ClusterControl
PTCOI;
PTWSP;
PTCOE;
CLUSTER RES
exit;
******************* APG command *******************************
hwver; !check APG version!
*************************** check seizure alarm ******************************
rasap;
racip:dev=RALT2-5464;
stdep:dev=RALT2-5464;
*********************** semipermanent connection data *************************
EXSCP:name=BSCKHS1_0;
stdep:dev=C7ST2C-0;
**************** delete DIGITAL PATH QUALITY SUPERVISION alarm ***************
dtqsr:dip=all,es,ses,sf;

dtqsr:dip=all,es2,ses2,sf;
************************************ buckup********************************
SYBUE;
!Passive Dump!
SYBUP:FILE;
!Make Dump!
;
!Confirm!
SYBFP:FILE;
!Check Dump File!
SYTUC;
!Change/Rotate Software!
SYBUI;
!Activate APG40!
SYBUI:DISC;
!Activate IOG20!
sybue; !stop automatic backup!
sybup:file=refsw2; !send new backup!
sybhp; ! voir si le buckup est hunging si pas hinging alors tu peut faire le bu
ckup!
*************************** pour eliminer sae ***********************
dbtri;
dbtse:tab=saactions,actnum=1;
dbtre:com;
********************* DISTRIBUTED GROUP SWITCH FAULT hlr *************
gdbli:unit=mux3-A-14;
gdble:unit=mux3-A-14;
gdstp;
*********************************************************************
RASAP;
!SEIZURE SUPERVISION OF DEVICES IN BSC ALARMED DEVICES!
RASAR:DETY=RALT2; !CLEAR ALARM!
RLVAP;
!CELL SEIZURE SUPERVISION OF LOGICAL CHANNELS ALARMED OBJECTS
DATA!
RLVAR:CHTYPE=TCH; !CLEAR ALARM!
**************************** restriction sur BSC *****************************
RLSBP:cell=all;
rlsbc:cell=all,acc=clear;
******************** rp
EXrpP:RP=ALL;
EXRPP:RP=548;
REPRI:RP=195;
REMRI:RP=195,pcb=RPPS1;
RECRI:RP=195;
EXEMP:RP=548,em=all;

fault *********************************
!RP DATA!
!RP DIAGNOSIS-block RP!
!RP MANUAL INTERVENTION!
!RP REPAIR-deblock RP!
!what rp control!

************************************ others **********************************

SAOSP;
!VERSION OF APZ.! !APZ PRINTOUT !
RLSTP:CELL=ALL;
!CELL STATUS!
RLCFP:CELL=15642b; !CELL CONFIGURATION FREQUENCY DATA!
RLDEP:CELL=15642b; !CELL DESCRIPTION DATA!
RLCPP:CELL=15642b; !CELL CONFIGURATION POWER DATA!
RLSSP:CELL=15642b; !CELL SYSTEM INFORMATION SACCH AND BCCH DATA!
RLSLP:CELL=15642a; !CELL SUPERVISION OF LOGICAL CHANNEL AVAILABILITY DATA!
RLSBP:CELL=15644B; !CELL SYSTEM INFORMATION BCCH DATA!
*************************** for checking number ****************************
hgrsp; !check state of HLR!
MGssp:imsi=603013023923296; !pour voir si le tel est ferme!
mgssi:imsi=661707319; !pour voir si le telephone est fermi!
hgsdp:msisdn=213661707319,all;
ctrai:msisdn=numero;

**************** pour chercher les cmd utilise dans winfiol ***************

APLOC;
alogfind -e date -s rlstc
***************** localisation ********************
hgsdp:msisdn=213661698613,all; !pour recuperrer le N0 msc!
mgcap;
!pour verfifier le N0 msc!
MGSSP:IMSI=603011001111794; !pour recuperer le N0 de bsc!
Mgbsp:BSC=all; !voir bsc connecter a msc!
Mgcep:cell=all; !voir tout les cell connecter a bsc ou msc et prend le nom de b
sc!
******************* LOCALIZATION********************
hgsdp:msisdn=213659336995,all;
mgcap;
MGSSP:IMSI= 603012023656995;
ctrai:msisdn=213659336995;
TEST SYSTEM;
PRINT VAR MTV 93836:H'147;
END TEST;
Mgcep:LAI=603-01-19101;
************** renvoie d 'appel *******************
hgsdp:msisdn=213662210924,all; !pour CHECK LE RENVOI!
HGSSI:MSISDN=21368628632,SS=CFU,FNUM=021652487; !POUR FAIRE LE RENVOIE!
HGSSE:MSISDN=213661690431,SS=cFU;
! ANNULER LE RENVOIE!
hgsdp:connected;
hgsdp:msisdn=213661737019,ssda;
cdlcp; !call duration!
********************** pour mettre swap a un site ******************
MGCEP:CELL=37101A;
MGCEE:CELL=37101C;
MGCEI:CELL=37101C,CGI=603-01-37101-11013,BSC=BTINDFN;
MGBSP:BSC=ALL;
******************** BLOCK NUMERO **********************
HGSDP:MSISDN=213661601152,all;
HGSDC:MSISDN=213661601152,sud=oba-1; !ca est equivalent a obi-1 in et obo-1 out!
!blocage emission/reception obi-1 obo-1
!
**************************** Etat APG**********************************
aploc;
prcstate -l
cluster group
exit;
*************************GPRS**************************
rrgbp;
rrgbp:ncbd;
radep:dev=rtglt2-33;
ntcop:snt=etrtg-1;
ntcop:snt=etm2-2;
dtstp:dip=1rtglt;
rrmap:trapool=all;
******************* *S'IL Y A EDGE ***************
rxcap:mo=rxots-435-10-6;
rlbdp:cell=xxxx;

*************** *BSC avec /sans TRC******************

rrntp;
***********************CELL NEIGHBOUR********************
rlncp:cell=all;
********************************************************
*BLOCKING SUPERVISION OF DEVICE*
stbsp:dety=ralt;
******************* SAE CLEAR ****************
dbtsp:tab=saactions;
dbtri;
dbtse:tab=saactions,actnum=4;
dbtre:com;
***************** pb bscstf1 **************
gdstp;
gdbli:unit=xm-B-0-0;
gdble:unit=xm-B-0-0;
gdstp;

*************** ROUTAGE **************

ANBSP:b=all,rc=646;
anrsp:rc=646;
anrsp:rc=647;
anrsi:br=tmr-0&-3&-4,p01=1,r=cncp4to,ess=1,esr=0;
anrsi:br=tmr-1&-2,p02=1,r=cncp4to,ess=0,esr=0;
anrpi:rc=646,cch=yes;
anrpe;
anrsp:rc=646,nop;
anrsp:rc=646;
anrai:rc=646;
anrzi:rc=646;
exrop:r=cncp3to;
c7rsp:dest=3-655;
anrsp:rc=;
aploc;
alogfind -s anrai
mml
anrsp:rc=all;
!
C7LDP:ls=3-469; !RP?!
C7STP:st=c7st2c-12; !RP?!
EXRPP:RP=265;