Course No.

EE-301-F EE-303-F

EE-305-F

EE-307-F CSE-210F EE-309-F EE-323-F

EE-325-F EE-329-F EE-335-F --------

M.D UNIVERSITY SCHEME OF STUDIES AND EXAMINATION BTech. III YEAR (ELECTRONICS & COMMUNICATION ENGINEERING) SEMESTER V Modified F Scheme effective from 2011 -12 Course Title Teaching Schedule Marks Examination of L T P Total Theory Practical Class Work COMMUNICATION Engg. 3 1 4 50 100 ELECTRONIC 3 1 4 50 100 MEASUREMENT & INSTRUMENTATION (EL,EI,IC,EE,EEE,AEI) ANALOG ELECTRONIC 3 1 4 50 100 CIRCUITS (EL,EI,IC,EE,EEE,AEI) ANTENNAS,WAVE 3 1 4 50 100 PROPAGATION& TV Engg. COMPUTER ARCHITECTURE 3 1 4 50 100 AND ORGANISATION (EL,EI,IC,Common with IV sem. CSE,IT ) MICROPROCESSORS AND 3 1 4 50 100 INTERFACING (EL,EI,IC,CSE,IT,EEE,AEI) ELECTRONIC - 2 2 25 25 MEASUREMENT & INSTRUMENTATION LAB (EL,EI,IC,EE) ANALOG ELECTRONIC - 2 2 25 25 CIRCUITS LAB (EL,EI,IC) MICROPROCESSORS AND - 2 2 25 25 INTERFACING LAB (EL,EI,IC,CSE,IT,EEE,AEI) PRACTICAL TRAINING - 2 2 GERNERAL PROFICIENCY TOTAL 18 6 8 32 50 425 600 75

Total Marks

Duration of Exam

150 150

3 3

150

150 150

3 3

150

50

50 50

3 3

50 1100

Note: 1) Students will be allowed to use non-programmable scientific calculator. However, sharing of calculator will not be permitted in the examination. 2) Assessment of Practical Training-I, undergone at the end of IV semester, will be based on seminar, viva-voce, report and certificate of practical training obtained by the student from the industry. According to performance letter grades A, B, C, F are to be awarded. A student who is awarded F grade is required to repeat Practical Training.

EE-301-F

COMMUNICATION ENGINEERING

L T P 3 1 -

Theory Class work Total Duration of Exam

: 100 Marks : 50 Marks : 150 Marks : 3 Hours

NOTE: For setting up the question paper, Question No. 1 will be set up from all the four sections which will be compulsory and of short answer type. Two questions will be set from each of the four sections. The students have to attempt first common question, which is compulsory, and one question from each of the four sections. Thus students will have to attempt 5 questions out of 9 questions. Section-A SPECTRAL ANALYSIS : Fourier Series, Fourier transforms, Convolution Theorem, Correlation, Cross-Correlation and autocorrelation. Section-B INFORMATION THEORY : Introduction to information and entropy, channel capacity for discrete and continuous channels, Shannons Theorem, Shannon-Hartley Theorem, Noisy channels, coding theory : Shannon-Fano coding, minimum redundance coding, maximization of entropy of a continuous message transmission rate, effect of medium on the information, selection of channels ,effect of noise and its minimization. Section-C RANDOM SIGNAL THEORY : Representation of random signals, concept of probability, probability of joint occurrence, conditional probability, discrete probability theory, continuous random variables, probability distribution function, probability density function, joint probability density functions. Section-D RANDOM SIGNAL THEORY : Statistical average and moments, Ergodic processes, correlation Function, power spectral density, central limit theory, response of linear system to random signals. Error function Covariance relation among the spectral densities of the two input-output random processes. Cross spectral densities, optimum filters. Introduction to Linear Block Code abd cyclic Codes

TEXT BOOK : 1. Principles of Communication Systems : Taub Schiling; TMH REFERENCE BOOKS. 1. Communication Systems : Singh and Sapre ; TMH 2. Communication Systems : A Bruce Carlson; TMH

EE-303-F L T P Marks 3 1 -

ELECTRONIC MEASUREMENT AND INSTRUMENTATION

Theory

: 100

Class work : 50 Marks Total : 150 Marks Duration of Exam : 3 Hours

NOTE: For setting up the question paper, Question No. 1 will be set up from all the four sections which will be compulsory and of short answer type. Two questions will be set from each of the four sections. The students have to attempt first common question, which is compulsory, and one question from each of the four sections. Thus students will have to attempt 5 questions out of 9 questions. Section-A

OSCILLOSCOPE: Block diagram, study of various stages in brief, high frequency CRO considerations measurement of phase &frequency,electrostatic deflection,dual trace &dual beam oscilloscope Sampling and storage oscilloscope .
Section-B
ELECTRONIC INSTRUMENTS: Instruments for measurement of voltage, current & other circuit parameters, Q-meters, R.F. power measurements, introduction to digital meter,chopper amplifier type voltmeter,true RMS voltmeter,electronic multimeter

Section-C
GENERATION & ANALYSIS OF WAVEFORMS: Block diagram of pulse generators, signal generators, function generators wave analysers, distortion analysers, spectrum analyser, Harmonic analyser, FFT analyser FREQUENCY & TIME MEASUREMENT: Study of decade counting Assembly(DCA), frequency measurements, period measurements, universal counter,

Section-D
TRANSDUCERS & SIGNAL CONDITIONING: Classification, Transducers of types: RLC photocell, thermocouples etc. basic schemes of measurement of displacement, velocity, acceleration, strain, pressure, liquid level & temperature. DC signal conditioning system, AC signal conditioning system, data acquisition and conversion system

TEXT BOOK: 1. A course in Electrical & Electronics Measurements & Instrumentation : A.K.Sawhney; Dhanpat Rai & Sons. REFERENCE BOOKS. 1. Electronics Instrumentation & Measurement Techniques : Cooper; PHI.

EE-305-F

ANALOG ELECTRONIC CIRCUITS

L T P 3 1 -

Theory Class work Total Duration of Exam

: 100 Marks : 50 Marks : 150 Marks : 3 Hours

NOTE: For setting up the question paper, Question No. 1 will be set up from all the four sections which will be compulsory and of short answer type. Two questions will be set from each of the four sections. The students have to attempt first common question, which is compulsory, and one question from each of the four sections. Thus students will have to attempt 5 questions out of 9 questions. Section-A

SINGLE AND MULTISTAGE AMPLIFIERS: Classification of amplifiers, distortion in amplifiers, frequency response of an amplifier, step response of an amplifier, pass-band of cascaded stages, RC-coupled amplifier, low frequency response of RC coupled stage, effect of an emitter bypass capacitor on low Frequency response, multistage CE amplifier . FEEDBACK AMPLIFIERS : Feedback concept, transfer gain with feedback, general characteristics of negative feedback amplifiers, input resistance, output resistance, voltage series feedback, current series feedback, current shunt feedback, voltage shunt feedback.
Section-B

OSCILLATORS: Sinusoidal oscillators, Barkhausen criteria, R-C phase shift oscillator, general form of oscillator circuit, wien-bridge oscillator, crystal oscillator.
Section-C

POWER AMPLIFIERS: Class A, B, and C operations; Class A large signal amplifiers, higher order harmonic distortion, efficiency, transformer coupled power amplifier, class B amplifier : efficiency & distortion; class A and class B push-pull amplifiers; class C power amplifier. OPERATIONAL AMPLIFIERS : Ideal and practical operational amplifiers, inverting and non-inverting amplifier, differential amplifier, emitter coupled differential amplifier, transfer characteristics of a differential amplifier, offset error : voltage and current, common mode rejection ratio (CMRR) .
Section-D

LINEAR APPLICATIONS OF OPERATIONAL AMPLIFIERS : Scale changer, phase shifter, adder, voltage to current converter, current to voltage converter, DC voltage follower, Bridge amplifier, AC coupled amplifier, AC voltage follower, Integrator, differentiator.

NON-LINEAR APPLICATIONS OF OPERATIONAL AMPLIFIERS : Comparators, sample & hold circuits, Logarithmic amplifier, anti-log amplifier, logarithmic multiplier, waveform generators , Miller & Bootstrap sweep generators, regenerative comparator (Schmitt Trigger), multivibrators, ADC. TEXT BOOK:
1. Agarwal - Foundations & Analog & digital electronics,Elsevier

2. Integrated Electronics: Milman Halkias, TMH. 3. Microelectronic Circuits : Sedra & Smith. REFERENCE BOOKS: 1. Operational Amplifiers:Gaikwad 2. Electronic Circuit Analysis and Design ( Second edition) : D.A.Neamen; TMH

EE-307-F

ANTENNAS, WAVE PROPOGATION &TV ENGINEERING

L T P 3 1 -

Theory Class work Total Duration of Exam

: 100 Marks : 50 Marks : 150 Marks : 3 Hours

NOTE: For setting up the question paper, Question No. 1 will be set up from all the four sections which will be compulsory and of short answer type. Two questions will be set from each of the four sections. The students have to attempt first common question, which is compulsory, and one question from each of the four sections. Thus students will have to attempt 5 questions out of 9 questions. Section-A Retarded potential, field of short dipole, Antenna pattern & antenna parameters Antenna pattern, Gain, Directivity, Radiation resistance, Aperture, Beam-width etc, Reciprocity theorem for antenna. . Section-B Wave equation for radiated fields from current and voltage sources in terms of electric scalar potential and magnetic vector potential .Fields and pattern of an infinitesimal dipole. Definition of various potentials used in antenna theory .: Relation between current distribution and field pattern of an antenna, linear antenna, half wave dipole, Antenna impedance, Directivity, Radiation resistance, Directional properties, Effect of ground on antenna pattern, Input impedance Broad band matching. Section-C Two element array, broad side, End fired pattern, Beam width pattern multiplication, multi element array and their properties, Synthesis of an array.parabolic feed antena, conical, helix, log periodic, horn, Microwave antenna ground waves propagation, Space waves propagation, Effect of Earth, Duct formation, Ionosphere, and sky wave Section-D TELEVISION SYSTEM: Picture transmission, sound transmission, picture reception, sound reception synchronization, receiver controls, color television. Monochrome picture tube, Beam deflection, screen phosphor, face plate, picture tube characteristics, picture tube, circuit controls. Television Camera Tubes: Basic principal, Image orthicon, Vidicon. . TEXT BOOKS : 1. Antennas by J.D.Kraus, TMH. 2. Antenna & Wave Propagation by K.D Prasad. 3. Monochrome and Color Television : R.R.Gulati ; New Age.

CSE- 210E L T

COMPUTER ARCHITECTURE & ORGANIZATION

Exam: Total:
Duration of Exam: 3 Hrs.

100 150

NOTE: For setting up the question paper, question no 1 will be set up from all the four sections which will be compulsory and of short answer type. Two questions will be set from each of the four sections. The students have to attempt first common question, which is compulsory, and one question from each of the four sections. Thus students will have to attempt 5 questions out of 9 questions. Section A Boolean algebra and Logic gates, Combinational logic blocks(Adders, Multiplexers, Encoders, de-coder), Sequential logic blocks(Latches, Flip-Flops, Registers, Counters) Store program control concept, Flynns classification of computers (SISD, MISD, MIMD); Multilevel viewpoint of a machine: digital logic, micro architecture, ISA, operating systems, high level language; structured organization; CPU, caches, main memory, secondary memory units & I/O; Performance metrics; MIPS, MFLOPS. Section B Instruction Set Architecture: Instruction set based classification of processors (RISC, CISC, and their comparison); addressing modes: register, immediate, direct, indirect, indexed; Operations in the instruction set; Arithmetic and Logical, Data Transfer, Control Flow; Instruction set formats (fixed, variable, hybrid); Language of the machine: 8086 ; simulation using MSAM. Section C Basic non pipelined CPU Architecture and Memory Hierarchy & I/O Techniques CPU Architecture types (accumulator, register, stack, memory/ register) detailed data path of a typical register based CPU, Fetch-Decode-Execute cycle (typically 3 to 5 stage); microinstruction sequencing, implementation of control unit, Enhancing performance with pipelining. The need for a memory hierarchy (Locality of reference principle, Memory hierarchy in practice: Cache, main memory and secondary memory, Memory parameters: access/ cycle time, cost per bit); Main memory (Semiconductor RAM & ROM organization, memory expansion, Static & dynamic memory types); Cache memory (Associative & direct mapped cache organizations. Section D Introduction to Parallelism and Computer Organization [80x86]: Goals of parallelism (Exploitation of concurrency, throughput enhancement); Amdahls law; Instruction level parallelism (pipelining, super scaling basic features); Processor level parallelism (Multiprocessor systems overview). Instruction codes, computer register, computer instructions, timing and control, instruction cycle, type of instructions, memory reference, register reference. I/O reference, Basics of Logic Design, accumulator logic, Control memory, address sequencing, micro-instruction formats, micro-program sequencer, Stack Organization, Instruction Formats, Types of interrupts; Memory Hierarchy.

Text Books: Patterson - Computer Organization & design, Elsevier Computer Organization and Design, 2nd Ed., by David A. Patterson and John L. Hennessy, Morgan 1997, Kauffmann. Computer Architecture and Organization, 3rd Edi, by John P. Hayes, 1998, TMH. Reference Books: Operating Systems Internals and Design Principles by William Stallings,4th edition,

EE-309-F
L T P 3 1 -

Microprocessors and Interfacing

Class work : 50 Marks Total : 150 Marks Duration of Exam : 3 Hours

NOTE: For setting up the question paper, Question No. 1 will be set up from all the four sections which will be compulsory and of short answer type. Two questions will be set from each of the four sections. The students have to attempt first common question, which is compulsory, and one question from each of the four sections. Thus students will have to attempt 5 questions out of 9 questions.
PART A THE 8085 PROCESSOR : Introduction to microprocessor, 8085 microprocessor : Architecture, instruction set, interrupt structure, and Assembly language programming. PART B THE 8086 MICROPROCESSOR ARCHITECTURE : Architecture, block diagram of 8086, details of sub-blocks such as EU, BIU; memory segmentation and physical address computations, program relocation, addressing modes, instruction formats, pin diagram and description of various signals PART C INSTRUCTION SET OF 8086 : Instruction execution timing, assembler instruction format, data transfer instructions, arithmetic instructions, branch instructions, looping instructions, NOP and HLT instructions, flag manipulation instructions, logical instructions, shift and rotate instructions, directives and operators, programming examples. PART D INTERFACING DEVICE :

8255 Programmable peripheral interface, interfacing keyboard and seven segment display, 8254 (8253) programmable interval timer, 8259A programmable interrupt controller, Direct Memory Access and 8237 DMA controller.
TEXT BOOKS : 1. 2. Microprocessor Architecture, Programming & Applications with 8085 : Ramesh S Gaonkar; Wiley Eastern Ltd. The Intel Microprocessors 8086- Pentium processor : Brey; PHI

REFERENCE BOOKS: 1. Microprocessors and interfacing : Hall; TMH 2. The 8088 & 8086 Microprocessors-Programming, interfacing,Hardware & Applications :Triebel & Singh; PHI 3. Microcomputer systems: the 8086/8088 Family: architecture, Programming & Design : Yu-Chang Liu & Glenn A Gibson; PHI. 4. Advanced Microprocessors and Interfacing : Badri Ram; TMH

EE-323-F

ELECTRONIC MEASUREMENT AND INSTRUMENTATION-LAB

L T P 0 0 2

CLASS WORK : EXAM : 25 TOTAL: 50 DURATION OF EXAM :

25

3 HRS

LIST OF EXPERIMENTS: 1) 2) 3) 4) 5) 6) Study blocks wise construction of a analog oscilloscope & Function generator. Study blocks wise construction of a Multimeter & frequency counter. Study Measurement of different components & parameters like Q of a coil etc using LCRQ meter. Study of distortion factor meter and determination of the % distortion of the given oscillator Determine output characteristics of a LVDT and Measure displacement using LVDT Study characteristics of temperature transducer like Thermocouple, Thermistor & RTD with implementation of a small project using signal conditioning circuits like instrumentation amplifier. Measurement of Strain using Strain Guage. To study differential pressure transducer & signal conditioning of output signal. Measurement of level using capacitive transducer.. Study of Distance measurement using ultrasonic transducer.

7) 8) 9). 10)

Note: Any Eight Experiments should performed from above list and two experiments can be suitably chosen on the contemporary topics

ANALOG ELECTRONIC CIRCUITS LAB EE-325-F

L T P
0 0 2

CLASS WORK EXAM TOTAL DURATION OF EXAM

: : : :

25 25 50 3 HRS

LIST OF EXPERIMENTS: (Select Any ten Experiments) 1. 2. Design & measure the frequency response of an RC coupled amplifier using discrete components. Design a two stage RC coupled amplifier and determine the effect of cascading on gain and bandwidth 3. Study the effect of voltage series, current series, voltage shunt, and current shunt feed-back on amplifier using discrete components. 4. 5. Design & realize inverting amplifier, non-inverting and buffer amplifier using 741 Op Amp. Verify the operation of a differentiator circuit using 741 op amp and show that it acts as a high pass filter. 6. Verify the operation of a integrator circuit using 741 op amp and show that it acts as a low pass filter. 7. 8. Design and verify the operations of op amp adder and subtractor circuits. Plot frequency response of AC coupled amplifier using op amp 741 and study the effect of negative feedback on the bandwidth and gain of the amplifier. 9. 10. 11. 12. 13. 14. Study of IC 555 as astable & monostable multivibrator Design & realize using op amp 741, Wein -bridge oscillator. To design & realize using op amp 741, square wave generator. To design & realize using op amp 741, logarithmic amplifier & VCCS. Study of 8 bit monolithic Analog to digital converter Study of R-2R ladder network & 8 bit monolithic Digital to Analog Converter.

Microprocessor & Interfacing Lab EE-329-F

L T P
0 0 2

CLASS WORK EXAM TOTAL DURATION OF EXAM

: : : :

25 25 50 3 HRS

List of Experiment ANY TEN EXPERIMENTS SHOULD BE PERFORMED: 1. Write a program using 8085 for Hexadecimal addition & subtraction of two numbers. 2. Write a program using 8085 Microprocessor for addition and subtraction of two BCD numbers 3. Write a program to perform multiplication and division of two 8 bit numbers using 8085 4. Write a program using 8086 for division of a defined double word (stored in a data segment) by another double Word division and verify. 5. Write a program using 8086 for finding the square root of a given number and verify. 6. Write a program using 8086 to copy 12 bytes of data from source to destination & verify. 7. Write a program to find maximum and minimum from series using 8086. 8. Write a program to initiate 8251 and to check the transmission and reception of character. 9. Write a program to interface ADC & DAC with 8085 & demonstrate generation of square wave. 10. Write a program to control the operation of stepper motor using 8085/8086 and 8255 PPI. 11 Write a program to interface 8X8 LED Matrix Display using 8085/8086 microprocessors and 8255 PPI. 12. Write a program to control the traffic light system using 8085/8086 and 8255 PPI. 13. Write a program to control simulated elevator 8085/8086 microprocessors and 8255 PPI.