.

NET Customization User Guide

AVEVA Solutions Ltd

Disclaimer
Information of a technical nature, and particulars of the product and its use, is given by AVEVA Solutions Ltd and its subsidiaries without warranty. AVEVA Solutions Ltd and its subsidiaries disclaim any and all warranties and conditions, expressed or implied, to the fullest extent permitted by law. Neither the author nor AVEVA Solutions Ltd, or any of its subsidiaries, shall be liable to any person or entity for any actions, claims, loss or damage arising from the use or possession of any information, particulars, or errors in this publication, or any incorrect use of the product, whatsoever.

Copyright
Copyright and all other intellectual property rights in this manual and the associated software, and every part of it (including source code, object code, any data contained in it, the manual and any other documentation supplied with it) belongs to AVEVA Solutions Ltd or its subsidiaries. All other rights are reserved to AVEVA Solutions Ltd and its subsidiaries. The information contained in this document is commercially sensitive, and shall not be copied, reproduced, stored in a retrieval system, or transmitted without the prior written permission of AVEVA Solutions Ltd Where such permission is granted, it expressly requires that this Disclaimer and Copyright notice is prominently displayed at the beginning of every copy that is made. The manual and associated documentation may not be adapted, reproduced, or copied, in any material or electronic form, without the prior written permission of AVEVA Solutions Ltd. The user may also not reverse engineer, decompile, copy, or adapt the associated software. Neither the whole, nor part of the product described in this publication may be incorporated into any third-party software, product, machine, or system without the prior written permission of AVEVA Solutions Ltd, save as permitted by law. Any such unauthorised action is strictly prohibited, and may give rise to civil liabilities and criminal prosecution. The AVEVA products described in this guide are to be installed and operated strictly in accordance with the terms and conditions of the respective licence agreements, and in accordance with the relevant User Documentation. Unauthorised or unlicensed use of the product is strictly prohibited. First published September 2007 AVEVA Solutions Ltd, and its subsidiaries 2007 AVEVA Solutions Ltd, High Cross, Madingley Road, Cambridge, CB3 0HB, United Kingdom

Trademarks
AVEVA and Tribon are registered trademarks of AVEVA Solutions Ltd or its subsidiaries. Unauthorised use of the AVEVA or Tribon trademarks is strictly forbidden. AVEVA product names are trademarks or registered trademarks of AVEVA Solutions Ltd or its subsidiaries, registered in the UK, Europe and other countries (worldwide). The copyright, trade mark rights, or other intellectual property rights in any other product, its name or logo belongs to its respective owner.

AVEVA .NET Customization

AVEVA .NET Customization

Contents

Page

.NET Customization User Guide

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1:1
About this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1:1 .NET Customization Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1:1
Common Application Framework Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Database Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Geometry Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shared Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Utilities Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Graphics Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AttributeBrowserAddin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ExamplesAddin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NetGridExample . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PMLNetExample . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PMLGridExample . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1:2 1:2 1:3 1:3 1:4 1:4 1:4 1:4 1:4 1:4 1:5

Sample Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1:4

Reference Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1:5 Compatibility with future versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1:5

How to Write an Addin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2:1

The IAddin Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2:1 The WindowManager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2:3
Window Creation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2:3

Addin Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2:6

2007 AVEVA Solutions Ltd

12.0

AVEVA .NET Customization

Writing a Command Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2:6 Command Events. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2:9

Resource Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2:9 Configuring a Module to Load an Addin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2:9

Menu and Command Bar Customization . . . . . . . . . . . . . . . . . . . . . 3:1

Configuring a Module to Load a UIC File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3:1 Editing the UIC File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3:2
Selection of Active Customization File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3:3 The Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3:4 List of Command Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3:6 Property Grid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3:10 Action Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3:12 Resource Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3:13

Database Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:1

Data Model Definition Classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:1
DbElementType . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DbAttribute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DbElementTypeInstance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DbAttributeInstance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:1 4:3 4:4 4:4

Element access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:5

DbElement Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:5 Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:7 Getting Attribute Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:9 Database Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:11 Storage of Rules and Expressions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:16 Comparison of Data with Earlier Sessions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:17

Filters/Iterators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:19
Iterators Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:19

Dabacon Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:19

Overview of Dabacon Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:19 Table Classes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:20

DBs, MDBs and Projects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:21

MDB Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:21 DB Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:22

Events

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4:23

2007 AVEVA Solutions Ltd

ii

12.0

AVEVA .NET Customization

Overview of Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overview of C# Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Capture of DB Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adding Pseudo Attribute Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DB/MDB Related Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4:23 4:23 4:24 4:24 4:26

PMLNet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5:1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5:1 Design Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5:1
Using PMLNet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5:1 .NET Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5:9 Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5:10

The AVEVA C# Grid Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6:1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6:1 Creating a C# Addin which Contains an AVEVA Grid Control. . . . . . . . . . . . . . 6:1 Providing Access to the Addin in PDMS Design or Outfitting Design . . . . . . . 6:3 Using the AVEVA Grid Control with Different Data Sources: . . . . . . . . . . . . . . 6:4 Adding an XML Menu to the Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6:5 Adding an Event to the Addin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6:6 Other Functionality Available within the PDMS Environment . . . . . . . . . . . . . . 6:7 Use of the C# Grid Control with PML . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6:7 AVEVA Grid Control API . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6:7 Input Mask Characters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6:12

2007 AVEVA Solutions Ltd

iii

12.0

AVEVA .NET Customization

2007 AVEVA Solutions Ltd

iv

12.0

AVEVA .NET Customization

Introduction

1
1.1

Introduction
About this Guide
This manual is designed to give a software engineer with experience of software development in C# using Visual Studio guidance on the development of .NET customization for the AVEVA PDMS and AVEVA Marine products.

1.2

.NET Customization Architecture

The introduction of a customization capability using Microsoft .NET technology has opened up a whole new world of customization and is particularly relevant for the integration of AVEVA products with other customer systems. .NET API's provided access to various aspects of the product including Graphical User Interface, Database and Geometry. As part of AVEVA's strategy of 'continual progression' the .NET customization capability has been introduced in such a way that it can be used alongside the existing PML based customization. Through the use of PML.NET, an enhancement to PML which allows the PML programmer to call .NET code, customization which utilizes the strengths of .NET compiled code and PML can be achieved.

Figure 1:1.

.NET customization Architecture

The above diagram illustrates the two new methods of customization using .NET technology. The first is via the concept of a .NET Addin and the second using PML.NET. Both methods provide a mechanism whereby a .NET assembly (dll) can be dynamically loaded into a module at runtime.

2007 AVEVA Solutions Ltd

1:1

12.0

AVEVA .NET Customization

Introduction

1.2.1

Common Application Framework Interfaces

The Common Application Framework (CAF) is an extensible framework which provides the .NET programmer with access to various services which support both application development and customization. The foundations of the CAF are provided by the two interface assemblies: Aveva.ApplicationFramework.dll Aveva.ApplicationFramework.Presentation.dll

These interfaces provide the following major services: Namespace: Aveva.ApplicationFramework AddinManager: This class provides properties and methods for the management of ApplicationFramework Addins. ServiceManager: This class defines an interface which provides a means by which the various components of the ApplicationFramework can publish their services. The ServiceManager also acts as a service provider responding to requests for services. It can also be used by applications and application addins to publish additional services. SettingsManager: This class provides properties and methods for the management of application settings which are stored in settings groups which are persisted between sessions.

Namespace: Aveva.ApplicationFramework.Presentation CommandBarManager: This provides access to the menus and commandbars of a CAF based application. It also has methods to load the definition of menus and commandbars from User Interface customization (UIC) files. CommandManager: This class defines an interface to provide the presentation framework client with a mechanism for the management of command objects which can be associated with Tools or other User interface objects. The action of invoking a tool (e.g clicking a ButtonTool) will cause the execution of the associated command object. It is possible to associated the same command object with a number of different user interface objects (e.g. ButtonTool on a Menu and a LinkLabel) thereby allowing for the centralisation of these user interface objects action within a command. Various state-like properties of a command (e.g. enabled/checked) would also be reflected in all user interface objects associated with a command. For example, disabling a command would cause all associated user interface objects to be disabled. User interface objects are associated with a command via a CommandExecutor derived class. ResourceManager: This class defines an interface to provide Addins with a simplified mechanism to access localizable resources.The ResourceManager provides a number of methods which allows an addin to then access the various types of resources (string, image, cursor, icon etc.) which resource files may contain. WindowManager: This provides access to the main application window, the StatusBar and a collection of MDI and docked windows. It also provides the addin writer with methods to create MDI and docked windows to host user controls.

1.2.2

Database Interfaces
The database related interfaces are provided by the interface assemblies: Aveva.Pdms.Database.dll & PDMSFilters.dll This interface has the following main classes: Namespace: Aveva.Pdms.Database DatabaseService: The sole purpose of this class is to open a project.

2007 AVEVA Solutions Ltd

1:2

12.0

AVEVA .NET Customization

Introduction

DbAttribute: The class has two purposes: 1. Instances of the class are used to identify and pass around attributes 2. The methods allow the retrieval of metadata about an attribute. e.g. type, size, Name, pseudo or not, etc. The class is valid for system attributes and UDAs.

DB: This class provides information on the opened DBs. DbElement: Instances of DbElement are used to identify an element. This is the main class for reading and writing to the database. The methods cover element creation element deletion copy getting/setting attributes and rules navigating the DB evaluating database expressions.

DbElementType: The class has two purposes: 1. Instances of the class are used to identify and pass around Element types 2. The methods allow the retrieval of metadata about an Element type. e.g. Name, description, allowed attributes and members etc.

The class is valid for system types and UDETs. DbEvents: This class contains the mechanisms for subscribing to database events. It covers savework, getwork, undo, redo, flush, refresh, drop events plus capturing general database changes. DbExpression: Class to hold a database expression. These are the same as PML1 expressions. Methods to evaluate expressions are on the DbElement class. DbPseudoAttribute: This Class allows pseudo attribute code to be plugged in for UDAs. DbRule: Class to hold a database rule DbUserChanges: This is passed through by the 'database change' event. It contains a list of database changes made since the last 'database change' event was raised. Changes may be queried down to the attribute level. MDB: Methods to do operations on an MDB. e.g. savework, getwork. Table: Various classes to access the internal Dabacon tables. E.g. the name table. Project: The main method is to open the MDB.

As well as the class methods there is a lot of functionality that can be accessed via pseudo attributes. The relevant pseudo attributes are listed where relevant.

1.2.3

Geometry Interfaces
The geometry related interfaces are provides by the interface assembly: Aeva.Pdms.Geometry.dll This interface has a number of geometry related classes. See reference documentation.

1.2.4

Shared Interfaces
Some general shared interfaces are provided in the interface assembly: Aveva.Pdms.Shared.dll This provides current element, selection changed events and Datal listing facilities.

2007 AVEVA Solutions Ltd

1:3

12.0

AVEVA .NET Customization

Introduction

1.2.5

Utilities Interfaces
Utility interfaces are provided in the interface assembly: Aveva.Pdms.Ultilities.dll This provides messaging, string utilities, tracing, undo and units. It also provides access to the command line but this is not supported

1.2.6

Graphics Interfaces
Interfaces to access the drawlist and colours are provided in the interface assembly: Aveva.Pdms.Graphics.dll The rest of this user guide will cover in detail how to write a .NET addin and an assembly containing classes with methods which are callable from PML. It will describe the use of the various .NET interfaces via the use of sample code.

1.3

Sample Code
A zip file (Samples.zip) containing the samples can be found in the installation directory. For the projects assembly references to be valid the zip file should be unzipped into the installation directory. It will create a Samples directory containing the sub-directories described below. If they are moved elsewhere then the references to assemblies in the installation directory will need to be updated. Samples are provided which are compatible with Visual Studio 2005, and Visual Studio 2005 Express.

1.3.1

AttributeBrowserAddin
A zip file (Samples.zip) containing the samples can be found in the installation directory. This example project creates an addin which implements a very simple database element attribute browser. It also illustrates the implementation of a command object to control the visibility of the docked window created by the addin.

1.3.2

ExamplesAddin
A zip file (Samples.zip) containing the samples can be found in the installation directory. .NET API Examples can be found in the ExamplesAddin project below the Samples directory. This is a C# addin which adds a ComboBoxTool on a Toolbar to the main menu. Each entry in the list runs a particular example. This can be loaded by adding the ExamplesAddin to the applications addin config file. Since these examples create and claim Design elements they need to be run in a Design multi-write database. There is an example config file in the ExamplesAddin directory.

1.3.3

NetGridExample
A zip file (Samples.zip) containing the samples can be found in the installation directory. An example of a .NET C# addin containing an AVEVA Grid Control.

1.3.4

PMLNetExample
A zip file (Samples.zip) containing the samples can be found in the installation directory. An example of a .NET class that has been made PML callable.

2007 AVEVA Solutions Ltd

1:4

12.0

AVEVA .NET Customization

Introduction

1.3.5

PMLGridExample
A zip file (Samples.zip) containing the samples can be found in the installation directory. An example of an AVEVA Grid Control hosted on a PML form.

1.4

Reference Documentation
Reference documentation for the various .NET interfaces is provided in the form of help files which can be found in the Documentation directory.

1.5

Compatibility with future versions

The new .NET API is a major step forward in providing a fast programmable interface to the AVEVA PDMS and AVEVA Marine database and functions. This first release at version 12.0 marks a major step forward and provides some very useful functions. However, it is an evolving interface and it is expected that there will probably be areas where functionality is missing or the interface could be improved. It is envisaged that there will be a certain amount of change for version 12.1 and that changes which are not upward compatible may be unavoidable. We will warn uses in advance of any such incompatible changes. At version 12.1, we expect to mark certain classes as 'complete' and then guarantee 100% compilation upward compatibility for use of these classes.

2007 AVEVA Solutions Ltd

1:5

12.0

AVEVA .NET Customization

Introduction

2007 AVEVA Solutions Ltd

1:6

12.0

AVEVA .NET Customization

How to Write an Addin

How to Write an Addin

Figure 2:1.

Writing a .NET Addin

The diagram in Figure 2 illustrates the main steps needed to create a .NET addin and configure a CAF based module to load the new addin. The following sections detail these various steps beginning with the writing of a .NET assembly which implements your addin.

2.1

The IAddin Interface

2007 AVEVA Solutions Ltd

2:1

12.0

AVEVA .NET Customization

How to Write an Addin

What distinguishes an addin from any other .NET assembly is that an addin must contain a class which implements the IAddin interface. When the CAF loads and starts an addin it interrogates the assembly for the class which implements this interface, creates an instance of this class and calls the IAddin.Start method. The following code is a simple example of a class which implements the IAddin interface. This is the AttributeBrowserAddin.cs file which is part of the AttributeBrowserAddin sample project which can be found in the samples directory. The Start method performs the initialization of the Addin.
using System; using System.Collections.Generic; using System.Text; // Add additional using statements using Aveva.ApplicationFramework; using Aveva.ApplicationFramework.Presentation; namespace Aveva.Presentation.AttributeBrowserAddin { public class AttributeBrowserAddin : IAddin { #region IAddin Members public string Description { get { return "Provides a simple attribute browser"; } } public string Name { get { return "AttributeBrowserAddin"; } } public void Start(ServiceManager serviceManager) { // Create Addins Windows // Get the WindowManager service WindowManager windowManager = (WindowManager)serviceManager.GetService(typeof(WindowManager)); // Create a docked window to host an AttributeListControl DockedWindow attributeListWindow = windowManager.CreateDockedWindow("Aveva.AttributeBrowser.AttributeList", "Attributes", new AttributeListControl(), DockedPosition.Right); // Docked windows created at addin start should ensure their layout is saved between sessions. attributeListWindow.SaveLayout = true; // Create and register addins commands

2007 AVEVA Solutions Ltd

2:2

12.0

AVEVA .NET Customization

How to Write an Addin

// Get the CommandManager CommandManager commandManager = (CommandManager)serviceManager.GetService(typeof(CommandManager)); ShowAttributeBrowserCommand showCommand = new ShowAttributeBrowserCommand(attributeListWindow); commandManager.Commands.Add(showCommand); } public void Stop() { } #endregion } } Figure 2:2. AttributeBrowserAddin Sample - AttributeBrowserAddin.cs

2.2
2.2.1

The WindowManager
Window Creation
An addin will typically expose its functionality to the user through the use of a graphical user interface. This can take the form of forms which are shown from menu or commandbar buttons or the addin writer may wish the addins graphical user interface to be hosted inside a dockable window or in an MDI child window. The facilities provided by the CAF WindowManager can be used to create these two types of window.

Figure 2:3.

Using WindowManager to create a Docked Window

The above code shows the use of the ServiceManager.GetService method to retrieve the WindowManager service and the use of the CreateDockedWindow method to create a docked window to host the AttributeListControl. The first argument, Key, to the CreateDockedWindow method needs to be a unique window identifier. To help avoid clashes between docked windows created by addins running within the same application then it is recommended to adopt the <CompanyName>.<AddinName>.<WindowName> naming convention for this property. An MDI window can be created via use of the WindowManager.CreateMdiWindow method. As illustrated in this example, an important step when creating docked windows is the correct setting of the SaveLayout property. This property controls whether information about

2007 AVEVA Solutions Ltd

2:3

12.0

AVEVA .NET Customization

How to Write an Addin

the layout and docking position is saved between application sessions. The code defines the default docking position as DockedPosition.Right, but the user can interactively change this and the persistence of this user preference between sessions is desirable. One aspect of the saving (serialisation) and restoring (de-serialisation) of this layout data is that this only works if only those docked windows for which there is layout information are present when the layout data is de-serialized. Therefore it is important that any docked window created during addin startup has this property set to true. If there is a mismatch between the number of docked windows in existence when the layout data is de-serialized then you will get one of the following warning message then the application starts up:

Warning: Loading Window Layout Aveva.AttributeBrowserWarning: window layout Warning: Loading Window Layout Aveva.AttributeBrowserWarning: window layout

- Missing DockedWindow: Failed to restore docked - Extra DockedWindow: Failed to restore docked

You should only see these warnings when either adding or removing an addin from a module.

IWindow Interface
The DockedWindow and MdiWindow both implement the IWindow interface which has the following methods and properties: void Hide() - Conceals the window from the user. void Show() - Displays the window to the user. void Float() - Displays the window as a floating window. void Dock() - Docks the window within the main window. void Close() - Destroys the window removing it from the windows collection. System.Windows.Forms.Control Control - Gets the control displayed in the window. bool Enabled - Gets or sets whether the window is enabled. bool Floatable - Gets or sets whether the window is floatable. int Height - Gets or sets the height of the window. bool IsFloating - Gets the floating state of a window. string Key - Gets the Key of the window in the WindowsCollection. string Title - Gets or sets the title/caption of the window. bool Visible - Gets or sets the visible state of the window. int Width - Gets or sets the width of the window. Size MaximumSize - Get or sets the maximum size of the window. Size MinimumSize - Get or sets the minimum size of the window.

Window Events
The Docked and MDI Windows also support a number of events such as Closed, Activated, Deactivated, Resized.

2007 AVEVA Solutions Ltd

2:4

12.0

AVEVA .NET Customization

How to Write an Addin

WindowManager Events
The window manager also supports two events: event System.EventHandler WindowLayoutLoaded - Occurs at startup just after the window layout has been loaded. This event can be used to update the state of commands which are being used to manage the visibility of a docked window. (see the ShowAttributeBrowserCommand.cs in the AttributeBrowserAddin sample) event WindowEventHandler WindowAdded - Occurs when a new docked or MDI window is created.

The StatusBar
The CAF also provides the addin writer with an interface to the StatusBar located at be bottom of the main application window.

The StatusBar is accessed from the StatusBar property of the WindowManager.

StatusBar statusBar = windowManager.StatusBar;

It has the following properties which can be used to control the StatusBar and its contents: bool Visible - Gets or sets the visibility of the StatusBar. string Text - Gets or sets the text to display in the default StatusBar text pane. int Progress - Gets or sets the progress bar value [0-100]. If this is set to 0 then the progress bar is hidden. string ProgressText - Text to describe the action being tracked by the progress bar. bool ShowDateTime - Gets or sets whether the Date and Time should be displayed on the StatusBar. bool ShowCapsLock - Gets or sets whether the panel showing the CapsLock state is displayed on the StatusBar. bool ShowNumLock - Gets or sets whether the panel showing the NumLock state is displayed on the StatusBar. bool ShowScrollLock - Gets or sets whether the panel showing the ScrollLock state is displayed on the StatusBar. bool ShowInsertMode - Gets or sets whether the panel showing the InsertMode is displayed on the statusbar. StatusBarPanelsCollection Panels - Gets the collection of application defined StatusBar panels. The StatusBar allows the user to create additional panels using the Panels collection property. The StatusBarPanelsCollection currently has methods to create StatusBarTextPanel objects and add them to the StatusBar.

2007 AVEVA Solutions Ltd

2:5

12.0

AVEVA .NET Customization

How to Write an Addin

Figure 2:4.

: Code to create a StatusBar Panel containing the project name.

The StatusBarTextPanel object has a number of properties which control its content and behaviour. It also supports PanelClick and PanelDoubleClick events. For details of these please refer to the reference help file.

2.3

Addin Commands
User access to an addin's functionality is typically accessed via main menus, context menus and tools on a commandbar. The CAF provides interfaces via the CommandBarManager for the creation of menus, commandbars and the various types of tool that they can contain. These various tools also support a traditional event style interface where the programmer provides event handlers to respond to the various events generated as a result of user interaction with the user interface. However this traditional approach to user interface development although still supported by the CAF is not recommended. The CAF also supports the ability to define menus, commandbars and their tools via a "User Interface customization" (UIC) file which is a XML file containing the definitions of the menus, commandbars and their contents including the values of their various properties. Details of how to create these UIC files will be covered later in this manual. A declarative XML based definition of the menus and commandbars requires the provision of a mechanism to associate each of the various user interface entities defined in the XML file with a call-back that invokes the necessary functionality (replacing the traditional event handlers). To achieve this, the addins functionality is exposed via a number of command objects. These command objects are loaded by an addin using the services of the CommandManager. The XML definition can then include information to associate a user interface entity such a menu entry or a button on a commandbar with a command object. Selection of the menu entry or clicking on the button will then cause the associated command to be executed. One of the advantages of a command based model is that it forces the decoupling of the user interface or presentation layer from the application logic. The application logic has no direct reference to the presentation layer entities. If application state needs to be reflected in the user interface then the application modifies the state of the command. The command knows which user interface entities are associated with it and takes the necessary steps to ensure that its internal state is reflected in the user interface. This is easily achieved for state such as "enabled", "visible" or "checked", but becomes complex when dynamic application state needs to be reflected in user interface entities such as a combo-box.

2.3.1

Writing a Command Class

The example below (Figure 6) is for a simple command class use to manage the visibility state of a docked window, in this case the AttributeBrowser docked window. The CAF provides an abstract base class from which every Command class must inherit. The

2007 AVEVA Solutions Ltd

2:6

12.0

AVEVA .NET Customization

How to Write an Addin

constructor for a Command class should set the base class Key property which is used to reference the command from within a UIC file. The Command base class has the following methods and properties which can be overridden by a derived Command class. void Execute() : This method must be overridden to provide the command execution functionality. CommandState GetState() : This method is called by the CAF to update the state of the contents of a context menu. The returned value is a CommandState enumeration for various states of a command. This enumeration can be treated as a bit field; that is, a set of flags. Bit fields can be combined using a bitwise OR operation. The command state is then reflected by the user interface. String Description : A description for the command. void Refresh(string context) : This method will be called whenever the CommandManager.ApplicationContext property is changed. This gives the command the opportunity to update its Enabled or Visible state in response to this context change. This command state change would then be reflected in the user interface. The Command base class also has a number of properties which are use to update the command state following user interface changes or vice-versa. bool Checked: If associated with a user interface entity such as a StateButtonTool then this property and the corresponding state of the user interface entity are kept synchronised. bool Enabled: Changes to this property are reflected in all associated user interface entities. ArrayList List: This property allows a command to communicate a list of string values to the user interface. This can be used when a command is associated with for example a ComboBoxTool. int SelectedIndex: This property is updated to indicate which item from a list has been selected by the user. object Value: This property holds the currently value of an associated user interface entity. bool ValueChanged: Before calling the execute method the CAF sets this property if the value of the user interface entity has changed. The flag is cleared when execution has finished. bool Visible: Changes to this property are reflected in all associated user interface entities. Registering a command with the CAF is done by adding an instance of a command class to the CommandManagers.Commands collection.

ShowAttributeBrowserCommand showCommand = new ShowAttributeBrowserCommand(attributeListWindow); commandManager.Commands.Add(showCommand);

using using using using System; System.Collections.Generic; System.Text; Aveva.ApplicationFramework.Presentation;

namespace Aveva.Presentation.AttributeBrowserAddin { /// <summary>

2007 AVEVA Solutions Ltd

2:7

12.0

AVEVA .NET Customization

How to Write an Addin

/// Class to manage the visibility state of the AttributeBrowser docked window /// This command should be associated with a StateButtonTool. /// </summary> public class ShowAttributeBrowserCommand : Command { private DockedWindow _window; /// <summary> /// Constructor for ShowAttributeBrowserCommand /// </summary> /// <param name="window">The docked window whose visibilty state will be managed.</param> public ShowAttributeBrowserCommand(DockedWindow window) { // Set the command key this.Key = "Aveva.ShowAttributeBrowserCommand"; // Save the docked window _window = window; // Create an event handler for the window closed event _window.Closed += new EventHandler(_window_Closed); // Create an event handler for the WindowLayoutLoaded event WindowManager.Instance.WindowLayoutLoaded += new EventHandler(Instance_WindowLayoutLoaded); } void Instance_WindowLayoutLoaded(object sender, EventArgs e) { // Update the command state to match initial window visibility this.Checked = _window.Visible; } void _window_Closed(object sender, EventArgs e) { // Update the command state when the window is closed this.Checked = false; } /// <summary> /// Override the base class Execute method to show and hide the window /// </summary> public override void Execute() { if (this.Checked) { _window.Show(); } else { _window.Hide(); } } } } Figure 2:5. AttributeBrowserAddin Sample - ShowAttributeBrowserCommand.cs

2007 AVEVA Solutions Ltd

2:8

12.0

AVEVA .NET Customization

How to Write an Addin

2.3.2

Command Events
The Command base class provides two events BeforeCommandExecute and CommandExecuted which enable the addin writer to write code to respond to the execution of any command object registered with the CommandManager. A command object can be retrieved from the CommandManger if its Key is known and event handlers can be attached to these events.

Command anotherCommand = commandManager.Commands["KeyOfCommand"]; anotherCommand.BeforeCommandExecute += new System.ComponentModel.CancelEventHandler(anotherCommand_Befor eCommandExecute); anotherCommand.CommandExecuted += new EventHandler(anotherCommand_CommandExecuted); The BeforeCommandExecute event handler is of type CancelEventHandler and is passed a CancelEventArgs object which enables the command execution to be cancelled by setting the Cancel property to true. void anotherCommand_BeforeCommandExecute(object sender, System.ComponentModel.CancelEventArgs e) { e.Cancel = true; }

2.4

Resource Manager
Another CAF service is the ResourceManager which provides addins with a simplified mechanism to access localizable resources. The ResourceManager supports the loading of ResourceSets which consist of a number of locale specific resource files with a given "basename".

resourceManager.LoadResourceFile("AttributeBrowserAddin");
This will load all resource files with a basename of "AttributeBrowserAddin". E.g.

AttributeBrowserAddin.resources (Invariant language locale) AttributeBrowserAddin.de.resources (German locale) AttributeBrowserAddin.ko-KR.resources (Korean-Korea locale)
Depending on the machine's regional settings resource lookups will firstly try to locate the resource from the corresponding locale specific resource file. If this is not found it will defer to the language invariant resource file. The ResourceManager provides a number of methods which allow an addin to access the various types of resources (string, image, cursor, icon etc.) which these resource files may contain. Each of the resource retrieval methods takes as an argument a resource identifier string and an optional resourceset name. If the resourceset name is omitted then it will default to a resourceset with the same name as the addin retrieving the resource.

2.5

Configuring a Module to Load an Addin

Having written an addin the next step is to get it to be loaded by a module. Each CAF based application has an XML addin configuration file which contains a list of the addins that the application should load at startup. The default location for this file is in the same directory as

2007 AVEVA Solutions Ltd

2:9

12.0

AVEVA .NET Customization

How to Write an Addin

the application executable. It has a filename of the form <Module Name>Addins.xml. For example the AVEVA PDMS module Design has a file called DesignAddins.xml. The content of this file is reproduced below. By default the addins are also expected to be in the same directory as the application executable. You can however specify the full path to the addin assembly including the use of UNC pathnames. If during addin development you do not wish to modify the addin configuration file in the install directory (this is particularly likely to be the case if you are using a server based installation) then the default location of the addin configuration file can be overridden using the environment variable CAF_ADDINS_PATH. You can then edit a copy of the file and point this environment variable at the directory you copy it to.
<?xml version="1.0" encoding="utf-8"?> <ArrayOfString xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"> <string>ExplorerAddin</string> <string>DrawListAddin</string> <string>MyDataAddin</string> <string>HistoryAddin</string> <string>ReferenceListAddin</string> <string>PipeCheckAddin</string> <string>OutputAddin</string> <string>FindAddin</string> <string>AttributesAddin</string> <string>C:\Documents and Settings\User1\My Documents\Visual Studio 2005\AttributeBrowserAddin\AttributeBrowserAddin\bin\Debug\AttributeBrowserAddin</string> </ArrayOfString>

2007 AVEVA Solutions Ltd

2:10

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

Menu and Command Bar Customization

User access to functionality provided via an addin is normally provided through the use of menus and/or tools on a commandbar. Reference was made earlier, in the section about addin commands, that the CAF provides a mechanism to allow the menus and commandbars for an application to be defined in a "User Interface Customization" (UIC) file. This section provides details of how a CAF based application can be configured to load a UIC file, and how the UIC file can be edited using the applications interactive user interface customization tool.

3.1

Configuring a Module to Load a UIC File

Each CAF based application has an XML configuration file which contains a list of UIC files that the application should load at start-up. The default location for this file is in the same directory as the application executable. It has a filename of the form <Module Name>Customization.xml. For example the AVEVA Marine module Hull Design has a file called HullDesignCustomization.xml. The content of this file is reproduced below. By default the UIC files are also expected to be in the same directory as the application executable. You can however specify the full path to the UIC file including the use of UNC pathnames. It is also possible to define a project specific UIC file. The string "$1" in the UIC path will be replaced with the current project name. If during addin development you do not wish to modify the customization configuration file in the install directory (this is particularly likely to be the case if you are using a server based installation) then the default location of the customization configuration file can be overridden using the environment variable CAF_UIC_PATH. You can then edit a copy of the file and point this environment variable at the directory you copy it to.
<?xml version="1.0" encoding="utf-8"?> <UICustomizationSet xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/ 2001/XMLSchema-instance"> <UICustomizationFiles> <CustomizationFile Name="Hull General" Path="AVEVA.Marine.UI.HullGeneral.uic" /> <CustomizationFile Name="Hull Design" Path="AVEVA.Marine.UI.HullDesign.uic" /> <CustomizationFile Name="Project" Path="$1.uic" /> </UICustomizationFiles> </UICustomizationSet>

The order of the UIC files in this configuration file is significant. They are loaded in order since it is possible for a UIC file to define a tool which is hosted in a menu or on a commandbar defined in a UIC file already loaded. A new UIC file can be added to a module simply by adding a new line to the corresponding customization configuration file. The actual content of the UIC file will be created using the interactive user interface customization tool described below.

2007 AVEVA Solutions Ltd

3:1

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

As well as adding to the customization configuration file an addin can also load a UIC file directly using the AddUICustomizationFile method of the CommandBarManager. // Load a UIC file for the AttributeBrowser. CommandBarManager commandBarManager = (CommandBarManager)serviceManager.GetService(typeof(CommandBarManager)); commandBarManager.AddUICustomizationFile("AttributeBrowser.uic", "AttributeBrowser"); This UIC file will be loaded before those define in the Customization configuration file, so it must create its own menu or commandbar to host its tools.

3.2

Editing the UIC File

The content of a UIC file is created using the CAF based applications built-in interactive user interface customization tool which is accessed via the Customize entry at the bottom of the commandbar area popup menu.

The customization dialog is comprised of seven main areas: 1. CommandBar Preview Area- displays a preview of a selected CommandBar. 2. Active Customization File - allows the selection of a loaded customization file for editing. 3. Tree showing CommandBars, Menubars, Context Menus and Resource Files. 4. List of tools. 5. Property grid 6. Action buttons 7. Resource Editor - displayed when a resource file is selected.

2007 AVEVA Solutions Ltd

3:2

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

Figure 3:1.

Customization Dialog

Figure 3:2.

Customization Dialog - Resource Editor

3.2.1

Selection of Active Customization File

The customization system supports the concept of multiple configuration files.

2007 AVEVA Solutions Ltd

3:3

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

Figure 3:3.

Selecting the Active Customization File

Any number of levels of customization file can be defined either using the module customization configuration file or the CommandBarManager. AddUICustomizationFile() method, and they are layered on-top of each other in the order they appear in the list. Selecting an entry in the list will update the tree view (3) and listview (4) with all configuration information defined in the selected file and those above it. Any items in the tree or listview which are not defined in the currently active customization file are displayed with an italic font in grey. Any customization file which a user does not have write access to does not appear in the drop-down list, but its contents are included in the tree and list of tools.

Figure 3:4.

Customization Dialog: Indication of editable items

Here the Button "Save" is defined in the "ConnectionMap" customization file. It is displayed in italics along with the "Schematic Model Viewer" Command Bar since these items are not defined in the currently selected customization file. The selected customization file will also be made the active customization file and any edits will only be possible to customization information defined in this file.

3.2.2

The Tree
The tree is populated with a representation of the Active Customization file: CommandBars and their contents: Menubars and their entries and Context Menus defined in each of the

2007 AVEVA Solutions Ltd

3:4

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

configuration files above and including the currently selected file. It also contains a list of the currently loaded resource files. The Tree View supports the following user interactions:

Selecting a Node in the Tree

The property grid (5) is updated with the corresponding object so that its properties can be edited. Only objects which are defined in the currently active customization file can have their properties modified. Selecting a node in the tree which represents an object defined in a non-active file will update the property grid, but it will be disabled thus preventing modification. If the selected node represents a CommandBar then a representation of the CommandBar will be displayed in the Preview Area (1). If the selected node represents a resource file then the resource editor (7) will be displayed instead of the property grid.

Drag & Drop within the Tree

The tools owned by a MenuTool or a CommandBar can be re-ordered by dragging the tool to the new desired position. MenuTools owned by the MenuBar can also be re-ordered using drag and drop.

Node Context Menus

The context menu for the CommandBars Node contains the following operations: New Command Bar - Creates a new CommandBar with unique default name (CommandBar<N>).

The context menu for a CommandBar node contains the following operations: Delete - Delete the CommandBar. If the CommandBar contains tools then a confirmation MessageBox is displayed.

2007 AVEVA Solutions Ltd

3:5

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

The context menu for the MenuBar node contains the following operations: New Menu - Creates a new MenuTool with a unique default name (Menu<N>). The context menu for the Context Menus node contains the following operations: New Menu - Creates a new MenuTool with a unique default name (Menu<N>).

The context menu for a Tool node contains the following operations: First in group - Marks the tool instance as being the first in a group. It then gets a separator drawn above it. Delete - Removes the tool instance from the MenuTool or CommandBar.

3.2.3

List of Command Tools

The list is populated with each of the tools defined in each of the configuration files above and including the currently selected file. The list supports the following user interactions:

Selecting a Node in the List

The property grid (5) is updated with the corresponding tool object so that its properties can be edited. Only objects which are defined in the currently active customization file can have their properties modified. Selecting a tool which is defined in a non-active file will update the property grid, but it will be disabled thus preventing modification.

Drag & Drop from the List to the Tree

Tools can be dragged from the list and dropped into a MenuTool or a CommandBar in the Tree. It is also possible to add tools to a menu or commandbar defined in a higher level customization file. This allows the user to integrate their tools into an existing system defined menu hierarchy and extend system toolbars as well as creating new top level menus and new commandbars. One possible risk of adding tools to menus or toolbars defined at a higher level is that the higher level structure might at a later date be modified making these tools "orphaned", or making the data which is stored to indicate their position within the host invalid. To warn of this, these tools are displayed in red within the tree. Here the "User" defined button "Sweden" had been added to the "System" defined commandbar "Standard". Also a button "Italy" defined at project level has been added to this "System" commandbar.

2007 AVEVA Solutions Ltd

3:6

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

List Context Menu

The list has the following operations on a context menu:

Delete - Deletes the currently selected tool. If the selected tool is not editable then the delete operation is disabled. If the tool has been used then a warning message is displayed to confirm that the delete should be carried out.

2007 AVEVA Solutions Ltd

3:7

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

Creates a new tool of the required type with a unique default name (Tool<N>) and adds it to the list.

Tool Types

When placed on a CommandBar the Button tool can have either an icon or a text caption. In a menu both the caption and the icon, if one is defined are displayed. The button tool simply executes the associated command when clicked.

The ComboBox tool allows selection from a list of items. The associated command provides the list via its List property.

The ControlContainer supports the hosting of any WinForms control. Here it is shown hosting a ProgressBar. The control it should host is set via the Control property which presents a list of the controls registered with the CAF using the CommandBarManager.Controls Hashtable property.
ProgressBar progBar = new ProgressBar(); progBar.Value = 50; commandBarManager.Controls.Add("ProgressBar",progBar);

2007 AVEVA Solutions Ltd

3:8

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

The FontList tool allows selection of a font from a pulldown list of installed fonts.

The Label tool allows the addition of a static icon and/or caption.

The List tool can only be use in a menu and will create a menu entry for each of the items returned from the List property of the associated Command object. This is typically used to implement a MRU list of files.

The MdiWindowList tool can also only be added to a menu. It supports the standard operations on the applications MDI Windows.

2007 AVEVA Solutions Ltd

3:9

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

Menu tools can be added to both an existing menu to create a sub-menu or to a CommandBar.

The PopupColorPicker displays a standard colour picker in a popup window.

The PopupControlContainer tool allows any WinForms control to be hosted in a popup window. Here the MonthCalendar control is being hosted.

The StateButton tool supports the Checked state.

The TextBox tool allows the entry of any string value.

Sorting List via Heading

It is possible to sort the list via interaction with the list column headings.

3.2.4

Property Grid
The property grid allows editing the various properties of the tools and CommandBars. The tree view (3) or the list of command (4) is kept up to date with any property changes.

2007 AVEVA Solutions Ltd

3:10

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

Figure 3:5.

Customization Dialog : Properties Grid

The command property can be changed by clicking on the button displayed when selecting the command property. This will display the following dialog:

By default the command type is set to Macro. The uses a special command class to invoke the entered single PML command. This enables the PML developer to use the interactive customization tool to create their own menus and commandbars without needing to write C# command classes. Changing the command type to "Core Command" will change the dialog to:

2007 AVEVA Solutions Ltd

3:11

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

Here a list of the currently loaded CAF Command objects is displayed for selection.

3.2.5

Action Buttons
The customization dialog has the following action buttons:

OK - Saves any modified customization files and updates the application user interface with any changes and closes the customization dialog.

Apply - Updates the application user interface with any changes.

Cancel - Restores the application user interface to state defined by customization files if any changes have been applied and closes the customization dialog.

2007 AVEVA Solutions Ltd

3:12

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

3.2.6

Resource Editor
The resource editor enables each of the currently loaded resource sets to be edited. It supports String, Icon and Bitmap resources. Each resource set can comprise of a number of resource files, comprising of the "Invariant Language" resource file and any number of locale specific resource files.

Figure 3:6.

Customization Dialog : View of string resource editor

2007 AVEVA Solutions Ltd

3:13

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

Figure 3:7.

Customization Dialog: View of bitmap resource editor

Resource Editor Command Bar

The resource editor command bar contains the following operations:

Save the resource file.

Copy a resource, so it can be pasted into another resource file.

Paste a resource.

2007 AVEVA Solutions Ltd

3:14

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

Delete a resource.

Add a new resource (Icons and Bitmaps only). New bitmaps or icons can be added by dragand-drop from a windows explorer. The resource id is generated from the filename capitalised and prefixed with "ID_". If there is a clash with an exiting resource then the following dialog will request confirmation of replacement.

String resource can be added for modified by editing them in the grid.

Select locale specific resource file for editing.

Add a new locale specific resource file to the resource file set.

Choosing a locale from the list of locales will add a new resource file specific for this locale. This can then be selected for editing.

2007 AVEVA Solutions Ltd

3:15

12.0

AVEVA .NET Customization

Menu and Command Bar Customization

Change layout style. The icon and bitmap tabs also have a popup menu which provides access to these functions as well as a rename function. Double clicking on a resource also enters the rename mode.

Using Resources for Properties

Properties of tools which are strings or the Icon property can use resources for their value. Reference to a resource is made using the form <ResourceSet Name>:<Resource Id> as shown below:

The caption and icon properties can be set on a tool in the tool list by drag-and-drop from the resource editor onto the tool.

Standalone Resource Editor

There is a standalone version of the resource editor available to enable resource files to be created and edited. This program is called "ResourceEditor.exe" and can be found in the installation directory. When started it will display a file selection dialog to enable you to choose an existing resource file or give the name of a new one.

2007 AVEVA Solutions Ltd

3:16

12.0

AVEVA .NET Customization

Database Interface

Database Interface
The classes fall into the following groups: 1. Data model definition classes 2. Basic database access, query and modification. 3. Filters and iterators 4. Dabacon table access 5. DB, MDB, Project access 6. Events and pseudo attribute plugins

4.1

Data Model Definition Classes

The classes are: DbElementType DbAttribute DbElementTypeInstance DbAttributeInstance

4.1.1

DbElementType
Overview
There is a single class for all element types. The purpose of the class is to: Instances of the class identify the element type. i.e. methods on other classes take a DbElementType as an argument rather than a string to denote an Element type. The DbElementType has 'value' semantics for comparison purposes. i.e. comparing of two DbElementTypes will always return true if they refer to the same type, even if they are different objects. Access the metadata associated with element types.

External to PDMS, the hash value can be used to uniquely identify an Element type. The hash value is a 32 bit integer.

Constructors
In C# a DbElementType object may be obtained in one of three ways: 1. Use the globally defined instances in DbElementTypeInstance. This is the recommended and easiest way to obtain a DbElementType.

2007 AVEVA Solutions Ltd

4:1

12.0

AVEVA .NET Customization

Database Interface

2. The static 'GetElementType' method may be used to return a DbElementType given the Element Type name. This is only needed for UDETs. The colon must be included as part of the name. 3. There is also a static 'GetElementType' method that may to be used to return a DbElementType given the hash value. This is only needed where a hash value has been stored outside of PDMS. 4. Various methods on other classes, such as DbElement will return a list of DbElementTypes.

Methods
The methods allow the Element type metadata to be accessed. E.g. Name Description BaseType (for UDETs) List of attributes List of UDAs Allowed members Allowed owners Types that may appear above this element type Types that may appear below this element type Element types that may be referenced from a given attribute on this element type Database types in which it occurs

Related ENUMS DbNounManual- Manual category DbType - DB type

Related Pseudo Attributes

Pseudo attributes that provide similar information on a particular element instance (i.e. on a DbElement) are: Attribute Name HLIS LIST LLIS OLIS REPTXT ATTLIST PSATTS UDALIS C# Data Type Description List of all possible types in owning hierarchy List of all possible member types List of all possible types in member hierarchy List of all possible owner types Reporter text used for element type List of all visible attributes for element List of pseudo attributes List of UDAs

DbElementType[] DbElementType[] DbElementType[] DbElementType[] String DbAttribute[] DbAttribute[] DbAttribute[]

2007 AVEVA Solutions Ltd

4:2

12.0

AVEVA .NET Customization

Database Interface

4.1.2

DbAttribute
Overview
This is very similar to DbElementType. There is a single class for all attributes. The purpose of the class is to: Access the metadata (i.e. data about data) associated with attributes. E.g. type, name, length Identify attributes. i.e. methods on other classes should always take a DbAttribute rather than a string as an argument to denote the attribute. Any comparison of attribute identity should be done by comparing DbAttribute objects.

The class should not be confused with the attribute value. The actual Attribute value for a particular Element can only be accessed via the DbElement class. Comparing two DbAttributes just compares whether they identify the same attribute, the comparison does not look at attribute values in any way. External to PDMS, the hash value can be used to uniquely identify an Attribute. The hash value is a 32 bit integer.

Constructors
In C# a DbAttribute object may be obtained in the following ways: 1. Use globally defined instances. Each attribute has a globally declared instance in the DbAttributeInstance class. This is the standard way of specifying an attribute. 2. Look up the DbAttribute given the attribute name. This is only needed for UDAs, since all other attributes can be obtained from the global instances. The colon must be included as part of the name. 3. Look up the DbAttribute given the attribute hash value. Generally this is only needed if reading the hash value from an external system. 4. Various methods on other classes, such as DbElement, will return a list of DbAttributesTypes.

Methods
The methods allow the following metadata to be accessed: Attribute Type Units Name Description Category Size Allowed Values Allowed ranges Is a UDA

2007 AVEVA Solutions Ltd

4:3

12.0

AVEVA .NET Customization

Database Interface

Is a pseudo attribute Whether the attribute may take a qualifier Example: Find the type of attribute XLEN. We use the global instance of XLEN on the DbAttributeInstance class.
using ATT=Aveva.Pdms.Database.DbAttributeInstance; DbAttributeType xlenTyp= ATT.XLEN.Type;

Related ENUMS
DbAttributeUnit- Type of units, e.g. distance or bore or none. DbAttributeType Type of attribute. One of INTEGER = 1, DOUBLE = 2, BOOL = 3, STRING = 4, ELEMENT = 5, DIRECTION = 7, POSITION = 8, ORIENTATION = 9 DbAttributeQualifier attribute has used to determine what sort of qualifier an

4.1.3

DbElementTypeInstance
This class contains instances of DbElementType for every element type in PDMS. These instances may be used wherever a DbElementType is expected. E.g. if a method MyMethod() takes an DbElementType, then you could write: e.g.
MyMethod(Aveva.Pdms.Database.DbElementTypeInstance.EQUIPMENT);

It is often convenient to add a using statement for these instances. E.g.

using NOUN=Aveva.Pdms.Database.DbElementTypeInstance; MyMethod(NOUN.EQUIPMENT);

4.1.4

DbAttributeInstance
This class contains instances of DbAttribute for every element type in PDMS. These instances may be used wherever a DbAttribute is expected. E.g. if a method MyMethod() takes a DbAttribute, you could write: e.g.
MyMethod(Aveva.Pdms.Database.DbAttributeInstance.XLEN);

It is often convenient to add a using statement for these instances. E.g

2007 AVEVA Solutions Ltd

4:4

12.0

AVEVA .NET Customization

Database Interface

using ATT=Aveva.Pdms.Database.DbAttributeInstance; MyMethod(ATT.XLEN);

4.2
4.2.1

Element access
DbElement Basics
Overview
This section describes the DbElement class. The DbElement class is the most widely used class and it covers a large proportion of the database functionality that will be used in practise. The methods fall into the following groups: Navigation Querying of attributes Database modifications Storage of rules and expressions Comparison across sessions

DbElement is a generic object that represents all database elements regardless of their type.

Constructors
An instance of a DbElement may be obtained as follows: There is a static GetElement() method with no arguments to return a 'null' DbElement. There is a static GetElement() method which returns a DbElement given a name. This name should include the '/'. There is a static GetElement() method which returns a DbElement given a ref(two long int array) and type. This is only needed where a reference has been stored externally to PDMS. There are many methods on various classes which return DbElements

e.g.

DbElement vess1 = DbElement.GetElement("/VESS1");

Identity
The DbElement object encapsulates the identity of the database object. Any comparison of database objects must be done using DbElements. The DbElement has 'value' semantics for comparison purposes. i.e. comparing of two DbElements will always return true if they refer to the same element, even if they are different objects. DbElement instances should be used in all cases where the identity of an element is being passed or stored. A DbElement can be identified externally to PDMS by a combination of the ref number AND type. The ref number is a two long integer, for example: =123/4567.

2007 AVEVA Solutions Ltd

4:5

12.0

AVEVA .NET Customization

Database Interface

Element Validity
A DbElement need not represent a 'valid' element. There are a number of reasons why a DbElement might be invalid: The element is in a DB not opened. The element has been deleted.

There is a IsValid()method to test if a DbElement is valid. If the DbElement is invalid then all attribute access and database navigation will fail for that DbElement.

Error Handling
The error handling techniques used are: 1. Some methods raise a PdmsException 2. Some methods return false if the operation can not be done. 3. For navigation operations, if the navigation does not succeed then a 'null' element is returned. A null element can be tested using the 'IsNull' method. It will have a reference of =0/0. Note: The error handling philosophy is likely to change at PDMS 12.1.

Basic Properties
DbElement has the following basic methods: ToString()- Returns the Name of the element. If unnamed, it returns the constructed name. GetElementType()- Returns the DbElementType. There are a number of pseudo attributes that return slight variations on name and type, as below. Type related: Attribute Name ACTTYPE AHLIS OSTYPE TYPE TYSEQU Name Related: Attribute Name CUTNAM CUTNMN C# Data Type String String Qualifier int int Description Full name of element, truncated to n characters Full name of element (without leading slash) truncated to n characters C# Data Type Qualifier Description Type of element List of actual types in owning hierarchy Shortcut for "Type of owner" Type of the element, ignoring UDET Type Sequence Number

DbElementType DbElementType (200) DbElementType DbElementType int

2007 AVEVA Solutions Ltd

4:6

12.0

AVEVA .NET Customization

Database Interface

Attribute Name FLNM FLNN ISNAMED NAMESQ NAMETY NAMN NAMTYP

C# Data Type String String Bool String String String String

Qualifier

Description Full name of the element Full name of the element (without leading slash) True if element is named Type. sequence number and name of element Type and name of the element Name of the element (without leading slash) Type and full name of element

4.2.2

Navigation
Basic Navigation
There are basic methods to navigate the primary hierarchy. e.g. consider the following hierarchy:

If we are sitting at Zone2, we can navigate as follows:

using NOUN=Aveva.Pdms.Database.DbElementTypeInstance; DbElement zone = DbElement.GetElement("/Zone1") DbElement temp=zone2.Next(); // temp is now Zone3 temp=zone2->Previous(); // temp is now Zone1 temp=zone2->Owner(); // temp is now Site1 temp=zone2->FirstMember(); // temp is now Pipe1 DbElement pipe1=temp; temp=zone2->LastMember(); // temp is now Equi1 DbElement temp=pipe1.Next(NOUN.EQUIPMENT); // temp is Equi1

2007 AVEVA Solutions Ltd

4:7

12.0

AVEVA .NET Customization

Database Interface

DbElement temp=pipe1.Previous(); // temp is null as there is no previous element. This can only be tested using the IsNull method Scanning the database is a very common operation. For this reasons there are additional iterator and filter classes that ease this task. These are described in the section on Filters/Iterators.

Pseudo Attributes Relating to Element Navigation

Attribute Name ALLELE CONNECTIONS CONNECTIONS H CONNER DDEP FRSTW MAXD MBACK MCOU MEMB OWNLST PARENT SEQU TYSEQU

Data Type
DbElement[] ) DbElement[] DbElement[] String Int DbElement Int DbElement[] Int DbElement[] DbElement[] DbElement Int Int

Qualifier
DbElementType

Description All elements in the MDB of a particular type Connections Connections for all descendants

Int

Connection error message Database depth hierarchy (World is 0) within

String

Reference of first world of given DB type in current MDB DB hierarchy depth of lowest level item beneath element

*DbElementType *DbElementType *DbElementType

Members in reverse order Number of Element Members of Given type All members, or members of specific type Owning hierarchy Reference of ascendant element of specified type Sequence Position in Member List Type Sequence Number

*DbElementType

'*'- qualifier is optional

Secondary Hierarchies
Standard navigation methods do not work for descending a secondary hierarchy. Pseudo attribute SMEMB must be used. E.g. to get the design elements below a GPSET, you must query the SMEMB attribute on the GPSET. Pseudo attributes relating to secondary hierarchies are: Attribute Name GPPRXS GROUPS SEXPND Data Type Description Group proxy items referring to element GPSETs in which element occurs Recursive expansion of SMEMB

DbElement[] DbElement[] DbElement[]

2007 AVEVA Solutions Ltd

4:8

12.0

AVEVA .NET Customization

Database Interface

Attribute Name SITEM SMEMB

Data Type

Description Reference from secondary hierarchy Immediate members in secondary hierarchy

DbElement DbElement[]

The difference between SMEMB and SEXPND is that SEXPND allows for recursive secondary hierarchies. Where there are no recursive possibilities, SMEMB and SEXPND will be the same. The following example illustrates the difference between SMEMB and SEXPND:

In the example there are two secondary nodes S1, S2. S1 holds element A, C, and S2 holds S1,D,G. For S1, SMEMB returns A,C SEXPND returns A,C For S2, SMEMB returns S1,D, G SEXPND returns A,C, D, G

4.2.3

Getting Attribute Values

Basic Mechanism
The attributes available on for a DbElement will depend on its type. E.g. a site will have different attributes to a branch. For this reason attributes are accessed through generic methods rather than specific methods. These generic methods pass in the identity of the attribute being queried (a DbAttribute object). There are separate methods for each attribute type (int, double etc), plus separate methods for single values or arrays. e.g.

2007 AVEVA Solutions Ltd

4:9

12.0

AVEVA .NET Customization

Database Interface

using ATT=Aveva.Pdms.Database.DbAttributeInstance; double length=myEle.GetDouble(ATT.XLEN); This call returns the value of attribute XLEN. If 'myEle' is not a BOX then an exception will be raised. If there is any doubt as to whether 'myEle' is a BOX or not, then there are a set of methods that return false if the attribute does not exists. E.g. e.g. using ATT=Aveva.Pdms.Database.DbAttributeInstance; double length; if (!myEle.GetValidDouble(ATT_XLEN,length)) { // handle error in some way } In addition there is a IsAttributeValid() method that can be used to test if an attribute is valid or not. The basic mechanism works for all attributes including UDAs and pseudo attributes. The attribute types supported are:

int, int[] double, double[] bool, bool[] string, string[] DbElement, DbElement[] DbElementType, DbElementType[] DbAttribute, DbAttribute[] Position Direction Orientation Expression Note: The methods that are called GetAttribute, GetAttributeArray are the 'getattribute' methods that return DbAttributes. Similarly the GetElement, GetElementArray methods are the 'getattribute' methods that return DbElements. This is confusing since GetElement is also the name of the method to return a DbElement given a name. We may change the names of these in the future.

List of Valid Attributes

There are two lists of valid attributes: 1. The list of system attributes. Typically these attributes can be queried and set. These can be queried using the GetAttributes() method. 2. There is a list of pseudo attributes that may be queried. Typically this list is large, running into the hundreds. This list can be obtained via the PSATTS attribute. N.B. querying PSATTS can be slow.

2007 AVEVA Solutions Ltd

4:10

12.0

AVEVA .NET Customization

Database Interface

Related pseudo attributes are: Attribute Name ATTLIST ATTRAW PSATTS RLIS UDALIS UDASET Data Type Description List of all visible attributes for element List of raw attributes List of pseudo attributes List of rules set List of UDAs List of UDAs set

DbElementType[] DbElementType[] DbElementType[] DbElementType[] DbElementType[] DbElementType[]

Qualifier
Many attributes take a qualifier. The qualifier is the extra information to make the query. Examples of where a qualifier is used are: 1. Querying a ppoint position (PPOS) requires the ppoint number 2. The ATTMOD attribute can be used to query when an attribute was modified but it needs to be given the identity of the attribute. 3. A direction/position may be queried with respect to another element The definition of what pseudo attributes take what qualifier is described in the data model reference manual. The DbQualifier class represents the qualifier. This can hold any type of qualifier, i.e. int, double,string, DbElementType, Attribute, position, direction, orientation. It can hold multiple qualifier values, although few current attributes require multiple valued qualifiers. There is a separate method to set the WRT element. There is a set of query routines that take a qualifier as an extra argument. e.g. to query the bore of ppoint 1:
DbQualifier qual=new DbQualifier(); qual.Add(1); double bore=myele.GetDouble(ATT.PPBO, qual);

Getting an Attribute as a Formatted String

If the attribute value is to go onto a form then the value must be formatted correctly. The correct formatting is not always obvious or available. Therefore there are special methods to return any attribute as a formatted string. This will format the attribute into the form that would appear at the command line. For example if the attribute is a position and we are working in finch unit, then something like 'W 39'4.7/16 N 59'0.85/128 U 4'0.31/ 128' might be returned. The method to do this is GetAsString(). Note: There is no generalised method for setting an attribute from a string.

4.2.4

Database Modifications
Overview
The following modifications are allowed:

2007 AVEVA Solutions Ltd

4:11

12.0

AVEVA .NET Customization

Database Interface

Set attribute Create element Delete element Copy element Change type Move element

The Modification Pipeline

When an element is modified, it is not simply the case of directly updating the database. For example, when setting an attribute the following sequence takes place: 1. Check that the attribute value is the right type 2. Check against any valid values or ranges 3. If the new value is the same as before, then return. 4. Check against the user access control defined in the system DB. 5. Check that the DB is open in write 6. Check LOCK flag 7. Do claim check, and claim if needed if DB is 'implicit claim' 8. Make attribute specific checks. 9. Make the actual database change. 10. Add to change list 11. Invoke attribute specific follow up code. 12. Update any dynamic rules affected It can be seen that making what appears to be a simple modification is actually quite complicated. In particularly a lot of errors are possible. Errors may be generated by any of the steps 1-2 plus steps 4-8. If an error occurs the code will raise a PdmsException. The calling code needs to allow for this. Clarification of some of these errors is as follows: Check that the attribute value is the right type - i.e. if a text attribute then the new value must be text. E.g. setting DESC to 99 will raise an error. Check against any valid values or ranges - This will check the value against any user provided criteria stored in the dictionary DBs. Check access control - An error will be raised if the modification is not allowed. An error will also be raised at this point if the attribute is not valid for the given element. Check that the DB is open in write - An error will be raised if 'read only'. Check LOCK flag - An error will be raised if the LOCK flag is true. Do claim check, and claim if needed (and implicit claim is allowed) - An error will be raised if: The DB uses explicit claims and the primary element has not been claimed. The primary element is claimed by another user or extract.

2007 AVEVA Solutions Ltd

4:12

12.0

AVEVA .NET Customization

Database Interface

Call the legality checking routines to ensure that the modification is valid - These checks are made by the plugged in application specific code. Thus potentially any error could be raised.

Claiming Elements
If a DB has been set up to be 'implicit' the user will claim elements as needed without having to do explicit claims. There are some methods on DbElement to claim/release individual elements or a hierarchy of elements. If working on a hierarchy of elements, and errors occur, then the system will still do what it can. There are also methods on the MDB class to claim/release a list of elements. Performance is improved by claiming or releasing elements in bulk, thus in general the MDB methods should be used rather than the ones on DbElement. The granularity of claim is at the level of primary element. This is described in the data management reference manual.

Pseudo Attributes Relating to Claims

Attribute Name CLMID CLMNUM CLMTIE

C# Data Type

Description Unique system ID of user claiming element User or extract number claiming element. Extract numbers are negative Reference to elements that automatically claimed along with element List of non primary offspring True if element may be claimed True if element and hierarchy may be claimed True if element may be released True if element and hierarchy may be released True if element is primary True if there are any primary elements amongst descendants Primary owning element (will be itself if primary) Elements in descendant hierarchy claimed to this user User name of user claiming element Elements in descendant hierarchy not claimed to this user are this

String int DbElement[]

NPDESC OKCLA OKCLH OKREL OKRLH PRIMTY PRMMEM PRMOWN USCLHI USERC USNCLH

DbElement[] bool Bool bool Bool Bool bool DbElement DbElement[] String DbElement[]

2007 AVEVA Solutions Ltd

4:13

12.0

AVEVA .NET Customization

Database Interface

Set Attribute
As for getting attributes, there is a family of methods for setting attributes depending on the attribute type.
ele.SetAttribute(ATT.DESC, "Example description");

There are no methods that take a qualifier. The code should always be prepared to handle any exceptions raised. There is a boolean method IsAttributeSetable to test if a given attribute may be set. This does not take the new value, so it is possible that the actual setting will still fail if the new value is invalid.

Creating Element
Creation is relatively straightforward. Elements can be created: Below a given element After a given element Before a given element

If creating an element below a given element then the position in the list must be given. E.g.
DbElement myNewPipe=myZoneElement.Create(1,NOUN.PIPE);

This creates a new PIPE below 'myZoneElement' as the first member. If the position is beyond the end of the current members list, it will create it at the end. An exception will be raised if the required type of element cannot be created at the required point. There is a boolean method IsCreatable to test if an element of a given type could be created at the required location. Deleting element

The method to delete an element is Delete(). e.g. MyEle.Delete();

All descendants in the primary hierarchy will be deleted. It will not delete elements in any secondary hierarchies.

There is a boolean method IsHierarchyDeleteable to test if an element can be deleted.

Copy As with Delete, the standard COPY method copies the primary hierarchy. The following points are relevant when copying: Certain attributes are not copied. e.g. NAME. For Name attributes, automatic renaming is possible The element may be copied to an existing element, or as a new element. Cross references within the copied hierarchy are automatically updated to the copied element. References external to the copied hierarchy are left unchanged.

There are further details in the reference manuals. An example of the DbElement method is:
myEle1.Copy(myEle2); myEle1.CreateCopyHierarchyAfter(myEle2,copyoption);

2007 AVEVA Solutions Ltd

4:14

12.0

AVEVA .NET Customization

Database Interface

The first example copies 'myEle2' on top of myEle1. The second example copies myEle2 and all its descendants to a new element after myEle1. There are methods to: Copy a single element to an existing element Copy an element and all its descendents to an existing element Copy an element and all its descendents to a new element Copy common attributes ('CopyLike') between existing elements

There is a separate class DbCopyOption to hold the options when doing a copy. These options are only available when copying an element and all its descendents. The element types must match if copying to an existing element. There is a boolean method IsCopyable to test if an element can be copied.

Moving Element
An element can be moved to a different location in the primary hierarchy. There are methods to: Inset before a given element Insert after a given element Insert into members list at the last position

Currently an element may only be moved within the same database. An error will be raised if the element is not allowed at the new location. There is a boolean method IsInsertable to test if an element can be moved. Currently there is not an exposed C# method for moving elements between DBs. This will be exposed shortly.

Changing Type
It is possible to change the type of certain elements. When a type is changed, the attributes are copied from the old to the new value. Any attributes not valid for the new type are lost. Thus a round trip of changing back to the original type may represent a loss of data.

Pseudo Attributes Relating to Modifications

Attribute Name DACCLA DACCOH

Data Type
bool bool

Qualifier

Description True if DAC allows element to be claimed True if DAC allows element hierarchy to be copied to another DB True if DAC allows element to be copied to another DB

DACCOP DACCRE

bool bool DbElementType

True if DAC allows element to be created

2007 AVEVA Solutions Ltd

4:15

12.0

AVEVA .NET Customization

Database Interface

DACDEL DACERR DACEXH DACEXP DACISS DACMOD MODATT MODDEL MODERR

bool String Bool Bool Bool bool Bool Bool string DbAttribute DbAttribute DbAttribute DbAttribute DbAttribute

True if DAC allows element to be deleted Returns the DAC error True if DAC allows hierarchy to be exported element

True if DAC allows element to be exported True if DAC allows element to be issued True if DAC allows attribute of element to be modified True if attribute of element can be modified True if element can be deleted Returns the error text that would occur if attribute was modified

4.2.5

Storage of Rules and Expressions

Database Expressions
Database expressions are PML1 expressions. E.g (XLEN * 1000 ). Expressions are of the following type: Double DbElement Bool String Position Direction Orientation As part of a rule Parameterisation of the catalogue

Database expressions are stored in various places in PDMS as follows:

There is a DbExpression class to hold an expression. An DbExpression may be obtained in one of the following ways: Use the static method internalParse() that creates a DbExpression from a string. e.g. internalParse("XLEN * 100" ) Retrieve an expression from a rule Retrieve an expression from a catalogue parameter

Having got an DbExpression there are two things that can be done with it: 1. Turn it back into text 2. Evaluate it against a given element The methods to evaluate an expression against an element are on the DbElement class. There are different methods depending on the expected result of the expression. The

2007 AVEVA Solutions Ltd

4:16

12.0

AVEVA .NET Customization

Database Interface

method names start with 'Evaluate'. The method that returns a double has an argument for the units (distance/bore/none). The result will always be in millimetres (mm). E.g.
DbExpression expr = DbExpression.Parse("DIAM OF PREV + 2"); double dval; DbAttributeUnit units = DbAttributeUnit.DIST; dval = nozz1.EvaluateDouble(expr4, units);

In this case the core system can work out that it is a distance, since DIAM is a distance. Thus although we specified that it was a distance, it was not strictly needed. Thus if the distance units were inch or finch then the '+2' would be interpreted as '+2inches'. However consider:
DbExpression expr = DbExpression.Parse("10"); double dval; DbAttributeUnit units = DbAttributeUnit.DIST; dval = nozz1.EvaluateDouble(expr4, units);

In this case we do not know if "10" is 10mm or 10 inches. We must tell the system that it is a 'distance' unit. The system then interrogates the current distance units to return the result. If the current distance units is mm, then dval will be 10.0. If the current distance units is inch/ finch then "10" is interpreted to mean 10 inches and is hence returned as 254. N.B. if the value is required to be formatted for output, then it must be converted back in all cases. A method will be added to return values in local units at a later point.

Rules
PDMS rules consist of an expression and a dynamic/static flag. When constructing a rule, the expression type is also needed. There are methods on DbElement to: Set a rule for any attribute. Get a rule for any attribute Evaluate a rule Verify that the rule result is up to date

Pseudo Attributes Relating to Rules and Expressions

Attribute Name NRULEE RCOU RULEER RULSET

Data Type Int Int String DbAttribute[]

Qualifier

Description Number of rule inconsistencies on element Number of rules on element

int

Text of "nth" rule error List of rules set

4.2.6

Comparison of Data with Earlier Sessions

There are no explicit methods exposed in C# which cover comparison across sessions. It is not currently possible to set the comparison date in C#.

2007 AVEVA Solutions Ltd

4:17

12.0

AVEVA .NET Customization

Database Interface

There are however a number of pseudo attributes that can be accessed as follows: Attribute Name ATTMOD ATTMODC ATTMODLIST ATTMODLISTC CRINFO DBSESS ELECRE ELECREC ELEDEL ELEDELC ELEMOD ELEMODC EXMOD HIST LASTM MSESS PRVSES RULEMOD RULEMODC RULEMODLIST RULEMODLISTC SESCLA SESSC SESSCA Data Type
Bool bool DbAttribute [] DbAttribute [] string int bool bool bool bool bool bool bool Int[] string int int bool Bool DbAttribute [] DbAttribute [] int string Int[] int DbAttribute DbAttribute DbAttribute int DbAttribute DbAttribute int int int int

Qualifier
DbAttribute DbAttribute int

Description True if specified attribute has been modified this session True if specified attribute has been modified since comparison date List of attributes modified since given session List of attributes modified since comparison date DB creation information Last DB session True if created since given session True if created since comparison date True if deleted since given session True if deleted since comparison date True if modified since given session True if modified since comparison date True if element modified in this extract History of sessions in which element or specified attribute were made Date of last modification Last session number Previous Session to that specified True if rule modified this session True if rule comparison date modified since

List of rules modified since given session List of rules comparison date Session Of Claim Comment for specified session List of pairs of DB number, last session number for all referenced DBs As for SESSCA, but searches all descendants for referenced DBs modified since

SESSCH SESSD SESSM SESSNO

Int[] string int int int DbAttribute

Date of specified Session Session Of Last Modification Current opened Session

2007 AVEVA Solutions Ltd

4:18

12.0

AVEVA .NET Customization

Database Interface

Attribute Name SESSU USERM

Data Type
string string

Qualifier
int DbAttribute

Description User creating specified session User making last modification

4.3
4.3.1

Filters/Iterators
Iterators
The DBElementCollection class can be used to iterate through the database hierarchy. The iterator is created with a root element and an optional filter. There are then methods to step through the hierarchy and return the element at the current location. E.g. to look for all nozzles below a given element
TypeFilter filt = new TypeFilter(DbElementTypeInstance.NOZZLE); DBElementCollection collection; collection = new DBElementCollection(ele, filt);

The collection can the be iterated through using foreach

foreach (DbElement ele in collection) { . Do something }

The iterator class has been written to avoid unnecessarily scanning parts of the database that will not match the filter. e.g. if looking for all boxes then the iterator will not bother to look below pipes.

4.3.2

Filters
There are a variety of ready built filter classes available. The main ones are: TypeFilter - True for given Element type(s) AttributeFalseFilter - True if given attribute is false AttributeTrueFilter - True if given attribute is true AttributeRefFilter - True if given attribute value matches given DbElement AndFilter - AND two existing filters. OrFilter - OR two existing filters BelowFilter - Filter to test if element is below an element for which the given filter is true.

4.4
4.4.1

Dabacon Tables
Overview of Dabacon Tables
In the Dabacon schema we can define an attribute to be an indexed attribute. Indexed attributes go into a Dabacon table.

2007 AVEVA Solutions Ltd

4:19

12.0

AVEVA .NET Customization

Database Interface

Tables consist of a list of key/value pairs. The key may be a string (ntable), integer (itable) or reference (ftable). The 'value' part of the pair is always the refno of the element having that attribute value. e.g. internally a name table may look something like: .. Janet = 123/456 John = 321/543 Jonathon = 111/321 Thus for a given name, the corresponding element can rapidly be found without having to scan the entire MDB. The keys in a name table must be unique. Integer and reference tables may contain the same key many times. e.g. internally a reference table may look like: . =123/456 =234/555 =123/456 =222/333 =123/456 =211/999 =123/458 =203/909 In the above table, element =123/456 has appeared in the table three times. This means that three different elements were all referencing =123/456 for this particular attribute. This is common. e.g. catalogue references are reference tables, and for these there may be hundreds of elements referencing the same catalogue component. A further point worth noting with respect to tables: Each DB has its own table. The entries in that table are for 'values' in that DB. Thus for the above ftable, =234/555 etc must be in this DB. However =123/456, =123/458 may be in a different DB. Indeed there may well be further references to =123/458 from other DBs. Hence to find all references to =123/456 we need to check the tables in each opened DB.

4.4.2

Table Classes
There are C# classes that enable direct access to the Dabacon tables. The classes are defined as follows: NameTable - for iterating through name tables RefTable - for iterating through reference tables IntTable - for iterating through integer tables These classes work on a single DB. In most cases, we really want to iterate through all DBs in the MDB as if it was one table. Thus for integer and name tables there are iterator classes that go across the whole MDB as follows: MdbNameTable - for iterating through a name table across entire MDB MdbIntTable - for iterating through an integer table across entire MDB There is no method for iterating through a reference table since the order of references in a table is not meaningful.

2007 AVEVA Solutions Ltd

4:20

12.0

AVEVA .NET Customization

Database Interface

There are also methods to return all entries for a given key. This is particularly useful for reference tables; these are methods of the MDB class. In C# there is a NameTable class. An example of C# code that looks for all names starting with the letter 'B' is as follows:
string nam1=new string(/B); string nam2=new string(/C); NameTable ntable = new MdbNameTable(db, DBAttribute.NAME, nam1, nam2); using (ntable) { foreach (Element ele in ntable) { // Do something here with each element } }

Freeing search tokens Dabacon allocates search tokens when scanning tables. It has a limited number of search tokens. If you get to the end of the table then the token is freed automatically. However if you stop the search before you get to the end then you must explicitly free the token. The IDispose method is used to free the underlying Dabacon token. Therefore ALWAYS scan the Dabacon table within a 'using' block to ensure that the Dispose method is called. If the underlying token is not freed then errors will be output to the PDMS command line of the form:
"xx dabacon search tokens - Expected none "

The error generating code does not actually free the tokens. So typically you will see the number climb as more tokens are used up and not freed. The messages will be generated until the database is closed.

4.5
4.5.1

DBs, MDBs and Projects

MDB Functionality
The MDB class exposes methods that act on the currently opened MDB. This is a singleton class. It contains methods to open/close an MDB savework/quitwork query claims claim/release elements extract operations, e.g. flush, refresh, extract claim, extract release, extract drop. get opened DBs return an element(s) of a given name return elements with matching values in name and integer tables (as described in previous section

Related pseudo attributes are:) Attribute Name Data Type Description

2007 AVEVA Solutions Ltd

4:21

12.0

AVEVA .NET Customization

Database Interface

OKDROP OKRLEX

bool bool

True if element may be dropped True if element may be extract released

4.5.2

DB Functionality
When an MDB is opened, a DB class instance is created for each opened DB. The functionality offered by this class falls into the following categories: Query the properties of the DB. e.g. number, MULTIWRITE or not Returning the world element for that DB Session information. e.g. when was the session written and by whom. There is a DbSession object that holds details on a database session. Return the DbElement in the system DB that represents this DB. This DbElement can then be used to query system attributes and additional pseudo attributes. The additional pseudo attributes available on the DbElement representing the DB are described below: Data Type
string String int String String DbElement[] String String String DbElement[] DbElement[] DbElement[] DbElement[] String string int bool Bool bool int bool DbElement[] DbElement[] int string int int int int

Attribute Name ACCEDB CLAIM CLCCNT CSESS DACC DBLC DCLA DSESS EXPIRY EXTALS EXTCLS EXTDES EXTFAM FILENAME FOREIGN HCCNT ISDBFR ISDRDB ISWORK LINKSN LPROT MDBCLS MDBLS NACCNT NAMEDB NXTDBN NXTEXN

Qualifier

Description DB access Implicit or explicit claims Claim list changes count Comment session entered for specified

Database access List of LOCs belonging to a DB Database claim mode Date of specified session Protected DB Expiry date Extract ancestors Extract children Extract descendants Extract family DB filename Originating project Header/Extract list changes count True if database is foreign True if database has drawings True if a working extract Linked session on parent extract Protected DB Flag List of MDBs in which DB is current List of MDBs to which DB belongs Non-additive changes count DB name Next DB number Next DB extract number

2007 AVEVA Solutions Ltd

4:22

12.0

AVEVA .NET Customization

Database Interface

Attribute Name NXTFDB NXTFLN PSESS SIZEDB STPDBS STPSES STYPDB TYPEDB USESS

Data Type
int int int int DbElement[] Int[] string string string

Qualifier

Description Next DB file and DB number Next DB file number

int

Previous session number Size of DB Stamps containing db Sessions used in at least one stamp DB sub type DB type

int

User creating session

In addition for any DbElement in any DB, the following pseudo attributes provide information on the current DB: Attribute Name DBAC DBCL DBCNTL DBEXNO DBFI DBFN DBNA DBNU DBREF DBTY DBVAR DBWRITE WDBNA Data Type
String String Bool int String int String int DbElement String Bool Bool STRING

Qualifier

Description DB Access, MULTIWRITE or UPDATE DB Claim True if element is in a control DB DB Extract Number DB filename DB file number DB name DB Number Reference of DB element DB type (DESI, CATA etc) True if element is in a variant DB True if element is in a writable DB Working DB name

4.6
4.6.1

Events
Overview of Events
The database events fall into the following groups; General capture of Database changes Writing Pseudo attributes for UDAs DB/MDB related events

4.6.2

Overview of C# Mechanism
The generalised mechanism in C# is as follows: There is a delegate to define the event signature. There is a method to add a delegate to the list of event handlers to be called.

2007 AVEVA Solutions Ltd

4:23

12.0

AVEVA .NET Customization

Database Interface

4.6.3

General Capture of DB Changes

DBlayer maintains a change list of Database changes. Users can subscribe to this list of changes. The list of changes is encapsulated in the DbUserChanges class. The DbUserChanges class has methods to determine what changes have been made. E.g. elements created or deleted or modified. The delegates are:
public delegate void ChangeEventHandler(DbUserChanges changes);

To add a subscriber (handler), the method is:

public static void AddChangeEventHandler(ChangeDelegate plug)

This will be in the DbEvents class. The subscribers receive a DbUserChanges class instance which has a list of elements changed and what the changes are. The events are fired as follows: At the end of running in a PML macro After the execution of a PDMS command on the command line When any action on a form has completed.

The event will only be fired if database changes have been made.

4.6.4

Adding Pseudo Attribute Code

Code can be plugged in to calculate the value of pseudo attributes. The code to do this must be registered in PDMS by passing in a C# delegate. Code can be registered in two ways: 1. Against a specific UDA. The code will then be invoked for all elements having this UDA. 2. Against a specific UDA and a specific element type. The code will only be invoked for all elements of that type. The same UDA may have multiple delegates registered for different element types. There is a different delegate for each attribute type. E.g. for integer attributes the delegate is:
public delegate double GetDoubleDelegate(DbElement ele, DbAttribute att, int qualifier);

These are defined in the DbPseudoAttribute class. The user must write a method that matches the method signature of the delegate. E.g. to write pseudo attribute code for a 'double' attribute, the user must write a method that has the signature defined by 'GetDoubleDelegate'. i.e. a method that takes a DbElement, a DbAttribute, int and returns a double. E.g. the following method would be valid:
// Double delegate for UDA static private double VolumeCalculation(DbElement ele,DbAttribute att,int qualifier) { // calculate the volume by multiplying the lengths along each side double x=ele.GetDouble(ATT.XLEN);

2007 AVEVA Solutions Ltd

4:24

12.0

AVEVA .NET Customization

Database Interface

double y=ele.GetDouble(ATT.YLEN); double z=ele.GetDouble(ATT.ZLEN); // Result of UDA must be returned return (x * y * z); }

An instance of the delegate containing the method must then be created and registered with PDMS. There are separate methods to register the different types of delegates. There are also separate methods to add a plugger for a particular element type. E.g. the two methods to add a GetDoubleDelegate are:
public static void AddGetDoubleAttribute(DbAttribute att,GetIntDelegate plug) public static void AddGetDoubleAttribute(DbAttribute type, GetIntDelegate plug) att, DbElementType

An example of registering a delegate is:

using System; using NOUN=Aveva.Pdms.Database.DbElementTypeInstance; using Ps=Aveva.Pdms.Database.DbPseudoAttribute; namespace Aveva.PDMS.Shared.Tests { static public void RegisterDelegate() { // get uda attribute DbAttribute uda=DbAttribute.GetDbAttribute(":VOLUME"); // Create instance of delegate containing "VolumeCalculation" method Ps.GetDoubleDelegate dele=new Ps.GetDoubleDelegate(VolumeCalculation); // Pass delegate instance to core PDMS. This will be invoked later // when :VOLUME is queried. // In this case registry for all valid element types. Ps.AddGetDoubleAttribute(uda,dele); } }

Code may be plugged by UDET as well as the base type. The following criteria are used to locate the right plugged code: 1. If a UDET, look for a delegate plugged by UDET and attribute. 2. Look for a delegate plugged by base type and attribute 3. Look for a delegate plugged by matching attribute only. e.g. you could add three delegates to calculate :WEIGHT. You could add one that calculates the :WEIGHT on a :MYELE, one that calculates the :WEIGHT of SCTN and one that calculates WEIGHT for any other element for which :WEIGHT is valid. A delegate only needs adding once at start up. The events do not allow for errors. Thus if the value can not be calculated then the pseudo attribute code should return a sensible default.

2007 AVEVA Solutions Ltd

4:25

12.0

AVEVA .NET Customization

Database Interface

4.6.5

DB/MDB Related Events

The following events can be captured: 1. Committing of any cached changes to the database. Called once prior to a Savework, undo, quitwork, setMark, Getwork 2. Pre and post events for the following actions: Savework, Getwork, undo, Redo, drop, flush, quit, refresh. These are only called if the action succeeds, and are there to cope with the changes. The pre events should not make any database changes. 3. Failure event for Savework, flush 4. Clearing out any local caches. 5. Claim/Release events Except for quit, the pre actions are really called post action but with the DB in the pre action state. The pre action is only called if the action succeeds. Most of the pre and post actions fall into just two categories: 1. Changes made to the database file itself, but not our view of it (Savework, Flush, Refresh, drop). 2. Changes in our view of the database, but no changes to the database file (Getwork, undo, Redo, quit). The interested parties are different in the two cases. When changing the database file, the interested parties are 3rd party systems outside of PDMS. When changing our view of the database it is the current PDMS session that needs to reflect the changes. E.g. update the 3D graphics and explorer. The events raised reflect this split. The events are: CommitPending - This is called to commit any outstanding change to the database. It is called prior to setmark, undo, redo, Savework, quit, Getwork. ClearCache() - This will be called after doing a temporary switch to a different session in a DB, or after doing a Getwork, undo, redo, quit.

Note: ClearCache may be called thousands of times within a single operation. Thus any event handlers must be fast. Pre and Post events for local changes. i.e. changes affecting the current view of the data. These will be Getwork, undo, redo. Pre and Post events for changes affecting the data on the DB. These will be Savework, refresh, drop, flush, refresh. These will pass the list of changes. For 'global' DBs, if the parent extract is at a different location, the flush event will be raised by the child extract.

Note: In this case the flush could still fail at the parent. Alternatively the daemon needs to raise the flush event. Post claim/release events Post failed Getwork/Savework

2007 AVEVA Solutions Ltd

4:26

12.0

AVEVA .NET Customization

PMLNet

5
5.1

PMLNet
Introduction
PMLNet allows you to instantiate and invoke methods on .NET objects from PML proxy objects. PML proxy class definitions are created from .NET class definitions at run time. These proxy classes present the same methods as the .NET class which are described using custom attributes. Proxy methods are passed arguments of known types which are marshalled to the corresponding method on to the .NET instance. The PML proxy objects behave just like any other PML object.

5.2

Design Details
PML callable assemblies are loaded by PDMS using the IMPORT syntax. Assemblies may be defined in potentially any .NET language, for example managed C++, C# or VB.NET. The PMLNet Engine loads a given assembly using reflection. The assembly may be located in the %PDMSEXE% directory, a subdirectory below %PDMSEXE% a mapped drive or on a UNC path. When the assembly is loaded PML class definitions are created for each PML callable class within the assembly. The PMLNet Engine only loads assemblies which are marked with the custom attribute PMLNetCallable. Only classes and methods which are marked as PMLNetCallable are considered. In order to create a valid PML Proxy class definition the .NET class and its methods must adhere to certain rules. Once an assembly has been loaded instances of PMLNetCallable classes may be created. No additional code to interface between PML and .NET is necessary. This is provided by the PMLNetEngine.

5.2.1

Using PMLNet
The diagram below shows how PDMS may be customised using PMLNet. A number of .NET API's are available which allow access to the current database session, drawlist, geometry and other functionality. Users are able to write their own managed code which accesses PDMS via these C# API's. It is not possible to directly call PML from C#. However there is an event mechanism which allows PML to subscribe to events raised from C# (these are shown in dashed lines below). Events are also raised when the database changes and can be subscribed to from C# (also shown in dashed lines). In this example the external C# assemblies share the same database session as Design i.e. they run in the same process and therefore see the same data.

2007 AVEVA Solutions Ltd

5:1

12.0

AVEVA .NET Customization

PMLNet

Limitations
Only .NET classes which are marked as PMLNetCallable and adhere to certain rules can be called from PML (these rules are described later) Module switching does not persist .NET objects. Core PML objects defined in FORTRAN or C++ are not persisted either. Passing other PML system/user objects to .NET e.g. DIRECTION, ORIENTATION, is not possible. It is possible to pass database references to .NET either as an array or String. It is also possible to pass an existing instance of a PML Net Proxy to .NET. It is not possible to call directly PML objects from .NET. The only way to call PML from .NET is via events. It is not possible to enter 'partial' namespaces as you might in C# and expect them to be concatenated.

E.g. the sequence:

USING NAMESPACE Aveva.PDMS !netobj = object namespace.NETObject ( )

will give an error. Objects and Namespaces In order to identify and load a particular class definition the PML proxy class is assumed to have the same name as the .NET class (PML callable classes must be case independent). This class name is passed to the PMLNetEngine which creates the .NET instance e.g.
!a = object netobject()

creates an instance of the .NET class netobject. To specify in which assembly this class is defined and resolve any name clashes the user needs to also specify the namespace in which the .NET class is defined using the following syntax:
USING NAMESPACE <string>

Where <string> is the namespace in which the class is defined.

2007 AVEVA Solutions Ltd

5:2

12.0

AVEVA .NET Customization

PMLNet

e.g. 'AVEVA.PDMS.PMLNetExample' The namespace is considered to be case independent. This namespace will remain current until it goes out of scope (e.g. at end of macro). When the user types: !netobj = object NetObject ( )

then all namespaces in the current scope will be searched to find a match. In this example, if 'Aveva.PDMS. PMLNetExample' is not currently in scope, then the error: (46,87) PML: Object definition for NETOBJECT could not be found. will be raised.

Object Names
Object names can consist of any alpha but not numeric characters (this restriction is imposed by PML). They are treated as case-independent. However, it is no longer necessary to define them in upper case - any mixture of upper and lower case letters will have the same effect.

Query Methods
The query methods on an object have been enhanced as follows: (a) Querying an object will show the namespace name as well as the object name: e.g.

var !x

< AVEVA.PDMS.NAMESPACE.NETOBJECT> AVEVA.PDMS.NAMESPACE.NETOBJECT

(b) There is a new query method to list all the methods of an object (including constructors)

Q METH/ODS
e.g.

q meth !x
<AVEVA.PDMS.NAMESPACE.NETOBJECT>AVEVA.PDMS.NAMESPACE.NETOBJECT

NETOBJECT ( ) NETOBJECT (REAL) ADD (REAL) REMOVE(REAL) ASSIGN(AVEVA.PDMS.NAMESPACE.NETOBJECT) DOSOMETHING(REAL, REAL, REAL)
Note that query methods will not list the methods on objects of type ANY, even though such methods are available on all objects.

(c) A new query:

Q NAMESP/ACES

2007 AVEVA Solutions Ltd

5:3

12.0

AVEVA .NET Customization

PMLNet

lists the namespaces currently in scope.

Global Method
There is a new global method on all objects:

.methods()
which returns a list of the methods on the object as an array of strings. e.g.

!arr = !x.methods() q var !x

returns:

<ARRAY> [1] <STRING> [2] <STRING> [3] <STRING> [4] <STRING> [5] <STRING> [6] <STRING>

'NETOBJECT ( )' 'NETOBJECT (REAL)' 'ADD (REAL)' 'REMOVE(REAL)' 'ASSIGN(AVEVA.PDMS.NAMESPACE.NETOBJECT)' 'DOSOMETHING(REAL, REAL, REAL)'

Importing an assembly Before an instance of a .NET object can be instantiated the assembly containing the class definition must be loaded. This is done using the IMPORT syntax as follows

IMPORT <string>
Where <string> is the case-independent name of the assembly

Method Arguments
Only PML variables of the following types may be passed to methods on .NET classes. In the table below the PML variable type is in the left column and the .NET equivalent variable type is in the right column. Data is marshalled in both directions between PML and .NET by the PMLNetEngine.

PML REAL STRING BOOLEAN

.NET double string bool

2007 AVEVA Solutions Ltd

5:4

12.0

AVEVA .NET Customization

PMLNet

PML ARRAY (these can be sparse and multi-dimensional)

.NET Hashtable

OBJECT Any existing PML Net PMLNetCallable class instance Arguments to PML Proxy methods are passed by reference so can be in/out parameters (in .NET output arguments must be passed by reference). Value Semantics PML Gadgets and DB elements have reference semantics when they are copied whereas all other objects have value semantics when they are copied. This is controlled by the Assign() method on the .NET class. So, for example if the Assign() method here copies the value then

!a = object netobject() !a.val(1) !b = !a !b.val(2) then q var !a.val() returns 1 and q var !b.val() returns 2
i.e. !a and !b do not point to the same object. In order to perform either a shallow or deep copy of the member data inside the .NET class the Assign() method must be defined on the Net class (see rules). This is analogous to overriding the operator "=" in C++.

Method Overloading
Overloading of methods is supported for all variable types in PML so a .NET Proxy can be created from a .NET class which has overloaded methods.

Custom Attributes
The custom attribute [PMLNetCallable()] is used to describe the PML interface for a .NET class. This metadata allows the PML callable assemblies to be self-describing. This clearly defines the class and allows an assembly to expose a subset of its public interface to PML. The PMLNetEngine uses this metadata to decide which .NET class definitions can be created in PML. Reflection is used to load an assembly and create PML class definitions. All classes and methods for which PML Proxy class definitions will be created must be marked as PMLNetCallable. The assembly itself must also be marked as PMLNetCallable. So, a PML callable .NET class in C# looks like this:
[PMLNetCallable()] namespace PMLNet { [PMLNetCallable ()] public class PMLNetExample

2007 AVEVA Solutions Ltd

5:5

12.0

AVEVA .NET Customization

PMLNet

{ [PMLNetCallable ()] public PMLNetExample() { } [PMLNetCallable ()] public void DoSomething(double x, double y, double z) { z = x + y; } } }

This class has a default constructor and a single method. Both the constructor and method are marked as PMLNetCallable along with the class itself. The assembly itself must also be marked as PMLNetCallable. This is normally done in the AssemblyInfo file as follows
using Aveva.PDMS.PMLNet; [assembly: PMLNetCallable()]

Private Data and Properties

In PML there is no concept of private members or methods - everything is public. Access to public data in .NET must be via properties or get/set accessor methods. Properties in .NET class are defined as get and set methods in PML. So, for example the following PMLNetCallable property in .NET
[PMLNetCallable()] public double Val { get { return mval; } set { mval = value; } }

would have the following Proxy methods in PML

REAL VAL() VAL(REAL)

Scope
PML variables are of two kinds: global and local. Global variables last for a whole session (or until you delete them). A local variable can be used only from within one PML function or macro. The lifetime of the .NET instance is controlled by the scope of the PML proxy.

2007 AVEVA Solutions Ltd

5:6

12.0

AVEVA .NET Customization

PMLNet

Instantiation
Classes can have any number of overloaded constructors but must have a default constructor which is marked as PMLNetCallable. The PML Proxy constructor instantiates an instance of the underlying .NET class. When the proxy goes out of scope the destructor destroys the underlying .NET instance.

ToString() Method
The string() method is available on all PML objects. For a .NET Proxy this will call the ToString() method on the .NET instance. If the ToString() method is overridden on the .NET class then this will be called.

Method Names
PML is case independent, so it is not possible to have MyMethod() and MYMETHOD() in .NET. PML will report non-unique object/method names.

Double Precision
Doubles are used in PMLNet to store reals and ints so doubles must be used in .NET (integers are not available in PML)

Events
Events on PMLNet objects may be subscribed to from PML. A PML callback on a particular instance may be added to an event on another PMLNet instance. Events are defined by a .NET component by associating the delegate PMLNetEventHandler with the event. This delegate has the signature
__delegate void PMLNetEventHandler(ArrayList __gc *args);

Where args is an array of event arguments of any PMLNet type (see table of valid types). The following code associates this delegate with an event
[PMLNetCallable()] public class PMLNetExample { [PMLNetCallable()] public event PMLNetDelegate.PMLNetEventHandler PMLNetExampleEvent; [PMLNetCallable()] public PMLNetExample () { } [PMLNetCallable()] public void Assign(PMLNetExample that) { } [PMLNetCallable()] public void RaiseExampleEvent() { ArrayList args = new ArrayList(); args.Add("PMLNetExampleEvent ");

2007 AVEVA Solutions Ltd

5:7

12.0

AVEVA .NET Customization

PMLNet

args.Add("A"); if (PMLNetExampleEvent!= null) PMLNetExampleEvent(args); } } This event can then be caught in PML by adding an appropriate callback to the instance raising the event !n = object pmlnetexample() !c = object netcallback() !handle = !n.addeventhandler('pmlnetexampleevent', !c, 'callback')

Where !n is the PMLNet instance on which the event will be raised !c is the instance of a PML object with a method callback() with the appropriate arguments

At some later time the event handler may be removed

!n.removeeventhandler('pmlnetexampleevent', !handle)
where !handle is the handle of the PMLNet delegate returned by addeventhandler(). Netcallback is a PML object defined as

define method .callback(!array is ARRAY) !args = 'NETCALLBACK object ' + !array[0] + !array[1] $P $!args endmethod Error Handling
Exception handling is placed around the Invoke method to handle .NET method invocation exceptions like TargetException, ArgumentException etc. The result of catching such an exception is to ultimately return a PMLError object from PMLNetProxy::Invoke() which results in a PML exception (1000,n) being thrown where 1000 is the module number for PMLNet. .NET can throw its own PML exceptions. The exception to throw is PMLNetException. For example
throw new PMLNetException(1000, 1, "PMLNetExample Exception");

This may then be handled inside a PML macro i.e.

handle(1000,1) endhandle

Any other exception within the loaded assembly itself is caught by the global exception handler inside PDMS.

Rules for Calling .NET

Certain rules must be adhered to when defining a .NET class which is PML callable. These are enforced by the PMLNetEngine when an assembly is imported. They are

2007 AVEVA Solutions Ltd

5:8

12.0

AVEVA .NET Customization

PMLNet

PML callable assemblies must be marked as PMLNetCallable and reside in the %PDMSEXE% directory, subdirectory of the application or UNC path. Only classes may be PML Callable (this excludes Structures, Interfaces, Enums, ). A PML callable class must be marked as PMLNetCallable. A PML callable method must be marked as PMLNetCallable. A PML callable method can only pass valid argument types (see table of types). PML callable classes and methods must be public. PML callable methods with default arguments cannot be defined. PML callable class and method names must be case independent. PML callable classes must have an Assign() method. PML callable classes must have a public default constructor which is PMLNetCallable.

If these rules are not adhered to then errors are reported to the trace log when the assembly is loaded and a PML class definition will not be created. If the class definition has not been defined then the following PML error will result (46,87) PML: Object definition for XXX could not be found.

Tracing
In order to output trace to a log file and the console window add the following lines to the exe's config file
<system.diagnostics> <switches> <add name="PMLNetTraceSwitch" value="4" /> </switches> </system.diagnostics> <appSettings> <add key="PMLNetTraceLog" value="C:\temp\PMLNetTrace.log" /> </appSettings>

This will create the file PMLNetTrace.log in C:\temp and log all the valid class definitions as they are imported.

5.2.2

.NET Controls
.NET controls can be hosted on a PML form. In order to do this PML provides a container gadget which can host the control. This container gadget has attributes to set and get its size and position and may be added to any PML defined form. It has similar behaviour to a Frame gadget in terms of docking, anchoring and positioning within an owning form. An instance of the .NET control is instantiated from PML. The PML container provides a method to add an instance of a .NET control to it. The .NET control may raise events which may be handled by PML. In order to customise the context menus of the .NET control from PML the ability to define a PML menu which can be shown when the .NET control raises an event is provided.

Creating a Container
A container on a form that can host the .NET control can be created in the following way in the form setup
container .exampleContainer PmlNetControl 'example' dock fill width 30 height 20

which can be docked and positioned.

2007 AVEVA Solutions Ltd

5:9

12.0

AVEVA .NET Customization

PMLNet

Hosting .NET Control

The control may be added to the container by setting the container's control to the .NET control's handle.
using namespace 'Aveva.Pdms.Presentation' !this.exampleControl = object PMLNetExampleControl() !this.exampleContainer.control = !this.exampleControl.handle()

Events
Events on the control are supported by PML delegates already described. These allow you to add popup menus to the control for example. Events may be subscribed to by adding an event handler as follows to the .NET control
!this. exampleControl.addeventhandler('OnPopup', !this, 'rightClickGrid')

where the method to call when the event is fired is defined as follows

define method .rightClickGrid(!data is ARRAY)

!this.exampleContainer.popup = !this.examplePopup !this.exampleContainer.showPopup(!data[0], !data[1]) endmethod

and the menu shown by the method which is added to the container is defined as follows

menu .examplePopup popup !this.examplePopup.add( 'CALLBACK', 'Add to 3D View', '!this.addToThreeDView()' )

5.2.3

Examples
The following examples are available in the Samples directory -

PMLGridExample
Example of a .NET grid hosted on a PML form

PMLNetExample
Example of a PML Callable assembly

2007 AVEVA Solutions Ltd

5:10

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

6
6.1

The AVEVA C# Grid Control

Introduction
This section describes how to use an instance of an Aveva C# Grid Control on a C# form. The example which is used in this documentation is supplied with the product. The Visual Studio project containing the source code is located in the following directory: Samples\NetGridExample Note: That you can only use the Aveva C# Grid Control on your own Visual Studio form if you have a design time licence for Infragistics version 6.1. Note: That you can run this C# Addin with PDMS without having an Infragistics licence.

6.2

Creating a C# Addin which Contains an AVEVA Grid Control

The supplied C# project is an example of a C# addin for use with PDMS. The C# addin includes an AVEVA C# Grid Control and some other Visual Studio WinForms gadgets to demonstrate how the Grid Control can be used with PDMS. The addin creates the docked window shown below when run within the PDMS Design or Outfitting Design module.

2007 AVEVA Solutions Ltd

6:1

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

The example C# code collects all the Equipment items within the current project and lists them inside the grid along with attribute values for Name, Type, and Owner. The data in the grid can be selected, sorted and filtered. Note: The following features of the example addin. These features make use of the published Grid Control API (see the section below entitled "AVEVA Grid Control API"). 1. The data in the grid can be exported to a Microsoft Excel file (XLS) by entering a path name in the text box beneath the grid and by clicking on the "Export to Excel" button. 2. The grid content can be previewed and printed by clicking on the "Print Preview" button. 3. The colour of the first row in the grid can be set either by choosing a colour in the drop down list, or by typing a valid colour into it. 4. The number of selected rows in the grid is written to a read-only text box. Note that this feature makes use of an event on the grid. (See the section below entitled "Adding an event to the C# Grid Control"). 5. Notice that there are two different context menus available on the grid. One is available when equipment items are selected:

2007 AVEVA Solutions Ltd

6:2

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

And the other menu is available from the header bar at the top of the grid:

Note: That these menu options will only become available once you have made some modifications to the Design.uic file through menu customization. See below for instructions on how to do this.

6.3

Providing Access to the Addin in PDMS Design or Outfitting Design

In order to see the addin inside PDMS Design you will need to do the following: 1. Build the addin.DLL inside the Microsoft Visual Studio project 2. The majority of the menus and toolbars in these two AVEVA modules are still currently defined in PML. If you wish access to your addin functionality to be provided from a additional entry on an existing menu then it is necessary to add the following line shown in red to the PML form file appdesmain.pmlfrm which resides within the PDMS directory: "PMLLIB\design\forms". The other lines are shown to help you locate where to add the PML menu. This will add a PML menu option beneath the Display menu in PDMS Design, and will allow you to open the addin.

!menu.add('TOGGLE', !menu.add('TOGGLE', !menu.add('TOGGLE', !menu.add('TOGGLE', !menu.add('TOGGLE', !menu.add('TOGGLE',

'My Data', 'Reference List', 'Attributes Utility', 'Search Utility', 'Search Results', 'New Addin',

'', '', '', '', '', '',

'My Data') 'Reference List') 'Attributes Utility') 'Find Utility') 'Output Utility') 'New Addin')

2007 AVEVA Solutions Ltd

6:3

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

Note that you could also create your own toolbar which contained a menu item to open/ close the addin.

6.4

Using the AVEVA Grid Control with Different Data Sources:

The supplied C# addin populates the grid with database items and their attribute values. The following data sources are available for this method of working. See the AVEVA Grid Control API section below for further information. NetDataSource(String TableName, Array Attributes, Array Items) NetDataSource(String TableName, Array Attributes, Array AttributeTitles, Array Items) NetDataSource(String TableName, Array Attributes, Array Items, String Tooltips

There are two other ways that an instance of the grid can be populated with data: 1. Populate the grid with non-database data The grid can be populated with collections of non-database data. The following data sources are available for this method of working. See the AVEVA Grid Control API section below for further information. NetDataSource(String TableName, Array columns, Array of Array of rows) NetDataSource(String TableName, Array columns, Array of Array of rows, String Tooltips)

2. Populate the grid with non-database data direct from a Microsoft Excel file

2007 AVEVA Solutions Ltd

6:4

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

The grid can be populated with non-database data from a Microsoft Excel file. The first row of the Microsoft Excel file will supply the headings for the grid and the other rows will supply the row data. The following data source is available for this method of working. See the AVEVA Grid Control API below for further information. NetDataSource(String TableName, string PathName)

6.5

Adding an XML Menu to the Form

Code has been added to the supplied addin to allow two different context menus to be used with the grid: a selection menu, and a header menu. To enable this to work with your session of PDMS Design you will need to use the Menu Customization utility described earlier in this document.

To add the menus you will need to do the following in the Menu Customization utility: 1. Add a new Context Menu, which has its name property set to: NewAddin.SelectMenu. This name is used by the code to locate the set of menus to display when the user makes a context menu selection on one or more equipment items in the grid. The C# method below from the addin class, is the code which loads the menu. The menus which you create in the Menu Customization Utility will be stored in the Design.uic file.

private void mCommandBarManager_UILoaded(object sender, EventArgs e) { String contextMenuKey = "NewAddin.SelectMenu"; if(mCommandBarManager.RootTools.Contains(contextMenuKey))

2007 AVEVA Solutions Ltd

6:5

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

{ MenuTool menu = (MenuTool)mCommandBarManager.RootTools[contextMenuKey]; mAddinControl.SelectionMenu = menu; } contextMenuKey = "NewAddin.HeaderMenu"; if(mCommandBarManager.RootTools.Contains(contextMenuKey)) { MenuTool menu = (MenuTool)mCommandBarManager.RootTools[contextMenuKey]; mAddinControl.HeaderMenu = menu; } }

2. Create a button and set the command to AVEVA.DrawList.Add. When this menu is used in the Addin it will add the selected equipment item(s) to the 3D view. 3. Assign the button to the context menu named NewAddin.SelectMenu. You can create other menu options (either from existing PDMS commands which have been exposed, or from existing PML methods and functions) in the same way and assign these to the context menu. 4. Create a second Context menu named NewAddin.HeaderMenu. This name is used by the code to locate the set of menus to display when the user makes a context menu selection on the header bar in the grid. 5. Create a button and set the command to AVEVA.Grid.ExportToExcel. When this menu is used in the Addin it will export the grid data to a Microsoft Excel file. 6. Assign the button to the context menu named NewAddin.HeaderMenu. You can create other menu options in the same way and assign these to the context menu.

6.6

Adding an Event to the Addin

There are several events which have been exposed for the AVEVA Grid Control. These are: 1. OnPopup(Array) 1. Array[0] is the x coordinate of the current cursor position 2. Array[1] is the y coordinate of the current cursor position 3. Array[2] contains the ID of each of the selected rows The position of the mousedown, and an array of selected items is passed through to the calling application when the context menu is used on the grid. 2. BeforeCellUpdate(Array) 1. Array[0] is the new value the user typed in 2. Array[1] is the Row Tag of the cell 3. Array[2] is the Column key of the cell 4. Array[3] is a Boolean. If you set it to "false" then the new value will NOT be allowed in the grid. If you set it to "true" then it is allowed. Cell data is passed back to the calling application as an array before a change is made in a cell of the grid (This assumes that the grid is in editable mode). The fourth argument of the array (Array[3]) can be set to false by the calling application in order to disallow the new value of the cell. 3. AfterSelectChange(Array)

2007 AVEVA Solutions Ltd

6:6

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

1. Array[0] contains the ID of each of the selected rows An array of selected items is passed through to the calling application. See the example C# code snippet below. The example code shows that the number of selected items is written to a text box.
private void netGridControl1_AfterSelectChange(System.Collections.ArrayLst args) { //Print the number of the selected rows in textbox2 if (args == null) { return; } Hashtable al = new Hashtable(); al = (Hashtable)args[0]; if (al == null) { return; } this.textBox2.Text = al.Count.ToString(); } Refer to Events for Event handling

6.7

Other Functionality Available within the PDMS Environment

Note the following additional functionality available with the Addin: 1. Selected equipment items can be dragged and dropped from the grid into the 3D View, MyData, or any other form within PDMS which is a drop target. This functionality is automatically available to the Addin as part of the Common Application Framework. 2. The Grid Control can be made editable, but any data which is changed in any cell of the grid will not be written back to the database. The calling application would need to handle the changes, and write this to the database, if relevant. 3. The Addin form can be docked and floated within the PDMS environment

6.8

Use of the C# Grid Control with PML

The C# Grid Control can also be used on a PML form. See the PMLGridExample code in the Samples directory.

6.9

AVEVA Grid Control API

The following table includes the API calls which have been made available for the Grid Control. Note: That you can only use the Aveva C# Grid Control on your own Visual Studio form if you have a design time licence for Infragistics version 6.1.

2007 AVEVA Solutions Ltd

6:7

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

Name NetDataSource(String TableName, Array Attributes, Array Items) NetDataSource(String TableName, Array Attributes, Array AttributeTitles, Array Items) NetDataSource(String TableName, Array columns, Array of Array of rows) NetDataSource(String TableName, Array Attributes, Array Items, String Tooltips) NetDataSource(String TableName, Array columns, Array of Array of rows, String Tooltips) NetDataSource(String TableName, string PathName) BindToDataSource(NetDataSo urce)

Type

Purpose Data Source constructor for database Attributes and database items. The Grid will populate itself with database attribute values. Data Source constructor for database Attributes and database items. The Grid will populate itself with database attribute values. The attribute titles can be added. Data Source constructor for column headings, and a set of rows. In this case the grid does NOT populate itself with database attribute values. Data Source constructor for database Attributes and database items. The Grid will populate itself with database attribute values. Data Source constructor for column headings, and a set of rows. In this case the grid does NOT populate itself with database attribute values. Data Source constructor for import of an Excel XLS or CSV File Bind Grid to NetDataSource

Data Source methods for populating the grid

General methods available for the grid getDataSource() SaveGridToExcel(String) NetDataSource Returns the data source that has been set in the grid Save All Data to Excel File. Note that this will retain all grid groupings and layout of data. The String should specify the full pathname, eg: 'C:\temp\file.xls'). Save All Data to a Worksheet in an Excel File. Note that this will retain all grid groupings and layout of data. Allow/disallow fixed headers. (Used when scrolling). Allow/disallow fixing of rows (Used when scrolling). Allow/disallow Outlook group facility

SaveGridToExcel(String, Worksheet) FixedHeaders(Boolean) FixedRows(Boolean) OutlookGroupStyle(Boolean)

2007 AVEVA Solutions Ltd

6:8

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

Name HideGroupByBox(Boolean)

Type

Purpose Hide the groupBy box. This will leave the Outlook style grouping in place and hence disallow the user from changing the grouping Set/unset column OutlookGroupStyle in

setGroupByColumn(colNum, Boolean) ColumnExcelFilter(Boolean) ColumnSummaries(Boolean) HeaderSort(Boolean) ErrorIcon(Boolean)

Allow/disallow Excel style filter on columns Allow/disallow Average, Count, etc on numeric columns Allow alphabetic column sorting. Allow/disallow the display of the red icon in the cell if a data value is not available. Set grid to single row selection. Switch Grid Events On or Off. Remove data & column headings. Set alternate rows to a different color. Set alternate rows to a different color. The default is: (251, 251, 255). Allow/disallow cells to be editable. Note: That if the user is allowed to write data to the grid, then this data does not get written back to the database. The calling code is in control of whether to either allow or disallow the change. This does not enable the user to add/remove rows, just to edit the content of the existing rows.

SingleRowSelection(Boolean) allGridEvents(Boolean) ClearGrid() setAlternateRowColor(String) setAlternateRowColor(Red Num, Green Num, Blue Num) EditableGrid(Boolean)

setLabelVisibility(Boolean) CreateValueList(Name, for List) ResetColumnProperties() SaveLayoutToXml(String) loadLayoutFromXml(String) Array

Show/Hide label. Create a value list for the grid. Reset column layout. Save the grid layout (not data) to a file on the file system. Load a stored layout on the file system (not data) into a grid instance.

PrintPreview() saveGridToExcel(string excelFile,string worksheet, string strHeader)

Opens a Print Preview Form (which also allows printing). Where strHeader is a user supplied string which is output to the first row in the Excel spreadsheet. The grid is then output starting in row #2.

2007 AVEVA Solutions Ltd

6:9

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

Name Methods on rows in the grid GetSelectedRows() GetSelectedRowTags() GetRows() GetRow(NUM)

Type

Purpose

Array of Array (rows) Array tags of row

Returns array of selected rows. Get the selected row tags. Returns array of rows.

Array of Array (rows) Array

Get the cells in the row number NUM. Get the cells in the row with the specified row tag. Get the Tag ID of the row. Allow/disallow a designated row to be editable. Set row color to a string (eg 'red'). Programmatically select the given row tags. Programmatically number NUM. select the row

GetRow(row tag) Array GetRowTag(NUM) setEditableRow(Integer, Boolean) setRowColor(NUM, String) setSelectedRowTags(Array rows) selectRow(NUM) getNumberRows() clearRowSelection() addRow(Array data) Real String

Get the number of rows in the grid. Clear row selection. Add a single row of data. If DB Element grid then only first array data is read. If not, then the Array data represents the data in each cell of the row. Delete selected rows. Delete one or more rows given by the "Tags" in the array. Delete one or more rows given by the "Tags" in the array. Scroll the selected row into view. Turn on/off the specified row. visibilty of the

deleteSelectedRows() deleteRows(Array data) deleteRows(Array data) scrollSelectedRowToView(Boo lean) setRowVisibility(double rowNum,bool) isRowVisible(double rowNum)

Query the visibility of the specified row

Methods on columns in the grid SetColumnMask(NUM, STRING(MASK))

2007 AVEVA Solutions Ltd

6:10

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

Name

Type

Purpose Set the Mask on column number NUM (see valid masks in the table below).

getColumnMask(NUM) setEditableColumn(Integer, Boolean) GetNumberColumns() AssignValueListToColumn(Na me, Column NUM)

STRING

Get the mask on the specified column (see valid masks in the table below). Allow/disallow a designated column to be editable.

REAL

Return the number of columns.

Assign the value list to a column. GetColumns() GetColumn(NUM) Array GetColumn(column tag) Array setColumnColor(NUM, String) setColumnImage(NUM, String) setColumnVisibility(colNum, Bool) getColumnKey(NUM) setNameColumnImage() String Get the cells in the column with a specified tag. Set column color to a string (eg 'red'). Set all cell images in column to the pathname of the specified icon. Show/Hide column. Get the Key of the column. Displays standard icons in a "NAME" attribute column when database items are used.. Resize columns to fit widest text. Set column to a designated width. Extend the last column. Resize columns to fit in available width of form Query the visibility of the specified column. Get the cells in the Column number NUM. Array STRING of Get the columns in the grid.

AutoFitColumns() SetColumnWidth(Column NUM, Column Width) ExtendLastColumn(Bool) ResizeAllColumns() isColumnVisibile(double colNum) Methods on cells in the grid GetCell(ROW, COL) STRING GetCell(row tag, column tag) setCellColor(row, col, String) STRING

Get the content of cell(ROW,COL) by row and column number. Get the content of cell(ROW,COL) by row tag and column tag. Set cell color to a string (eg 'red').

2007 AVEVA Solutions Ltd

6:11

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

Name setEditableCell(Row NUM, Col NUM, Boolean) setCellImage(row, col, String) setCellValue(rowNum, ColNum, STRING) AssignValueListToCell(Name, Row NUM, Column NUM)

Type

Purpose Allow/disallow a designated cell to be editable. Set cell image to the pathname of the specified icon. Programmatically set a cell value to a string.

Assign the value list to a cell.

6.10

Input Mask Characters

Masks can be set on data within a column. The mask will restrict the format and type of the data which can be entered into cells within the column. The mask can consist of the following characters: Character # . Description Digit placeholder. Character must be numeric (0-9) and entry is required. Decimal placeholder. The actual character used is the one specified as the decimal placeholder by the system's international settings. This character is treated as a literal for masking purposes. Thousands separator. The actual character used is the one specified as the thousands separator by the system's international settings. This character is treated as a literal for masking purposes. Time separator. The actual character used is the one specified as the time separator by the system's international settings. This character is treated as a literal for masking purposes Date separator. The actual character used is the one specified as the date separator by the system's international settings. This character is treated as a literal for masking purposes. Treat the next character in the mask string as a literal. This allows you to include the '#', '&', 'A', and '?' characters in the mask. This character is treated as a literal for masking purposes. Character placeholder. Valid values for this placeholder are ANSI characters in the following ranges: 32-126 and 128-255 (keyboard and foreign symbol characters). Convert all the characters that follow to uppercase. Convert all the characters that follow to lowercase. Alphanumeric character placeholder. For example: a-z, A-Z, or 0-9. Character entry is required. Alphanumeric character placeholder. For example: a-z, A-Z, or 0-9. Character entry is not required. Digit placeholder. Character must be numeric (0-9) but entry is not required. Optional minus sign to indicate negative numbers. Must appear at the beginning of the mask string.

&

> < A a 9 -

2007 AVEVA Solutions Ltd

6:12

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

Character C

Description Character or space placeholder. Character entry is not required. This operates exactly like the '&' placeholder, and ensures compatibility with Microsoft Access. Letter placeholder. For example: a-z or A-Z. Character entry is not required. All other symbols are displayed as literals; that is, they appear as themselves. Digit placeholder. A group of n's can be used to create a numeric section where numbers are entered from right to left. Character must be numeric (0-9) but entry is not required. Combination of these three special strings can be used to define a date mask. mm for month, dd for day, yy for two digit year and yyyy for four digit year. Examples: mm/dd/yyyy, yyyy/mm/dd, mm/yy. Combination of these three special strings can be used to define a time mask. hh for hour, mm for minute, ss for second, and tt for AP/PM. Examples: hh:mm, hh:mm tt, hh:mm:ss.

? Literal n

mm, dd, yy

hh, mm, ss, tt

2007 AVEVA Solutions Ltd

6:13

12.0

AVEVA .NET Customization

The AVEVA C# Grid Control

2007 AVEVA Solutions Ltd

6:14

12.0