Advances in Amine Reclaiming

Download as pdf or txt
Download as pdf or txt
You are on page 1of 13

Advances in amine reclaiming

Why there is no excuse for operating a dirty amine system


Arthur L Cummings, Glen Smith and Dennis K Nelsen MPR Services Inc

he benefits of reclaiming amine systems are trumpeted by many and doubted by others. Removing the contaminants generally results in smoother operations. Various methods of removing contaminants from amine solutions have been developed and improved over the years, primarily because of the enthusiasm of the users of reclaiming services. Suspended solids and hydrocarbons have been routinely dealt with by filtration and absorption technologies for longer than anyone can remember, but other contaminants have only relatively recently been targeted. Heat stable salts (HSS) were rarely spoken of 15 years ago, but are now universally known as an operational concern. Of the several potential chemical degradation products of amines, only HEEU and BHEEU (ureas formed by MEA and DGA, respectively) have had a longstanding routine way of dealing with them. As analytical capabilities improved, more and more contaminants can be identified and have become of interest. Amino acids (bicine, HES, and others) have received particular interest because of their strong contribution to corrosion. In recent years, amides, diamines, ureas and oxazolidones have become common targets of reclaiming efforts. Amides and oxazolidones have been converted back to useable amine. Over the last 15 years, reclaiming services have become available, employing a variety of technologies to remove contaminates. These are reviewed and compared.

and costs concerns. Twenty years ago, amine reclaiming consisted of built-in particle filtration and activated carbon units and, for MEA and DGA systems, a built-in thermal reclaimer. Now, operating companies can purchase mobile reclaiming services and permanent add-on reclaiming units for an ever-increasing array of dissolved, entrained and suspended contaminants anywhere in the world. What has changed? Why the rise in the perceived need for reclaiming and what is now available to meet that need? Product specifications and environmental concerns have also changed. Lower sulphur specs in finished products coupled with sourer feed stocks press ever-increasingly on the capacity of amine systems.1,2 Amine system downtime and upsets have a more visible connection to throughput and profits. Disposal of contaminated amine is hindered by fewer available options and higher costs. For many refineries, reclaiming is becoming the only option. Reclaiming removing the contaminants from amine solvents generally results in smoother operations, which, more and more visibly, translates to improved bottom line. Table 1 shows the bottom-line benefits of reclaiming to low impurity levels that four refiners documented. The positive effects of reclaiming seen by these refiners
Annual benefit to bottom line of maintaining low impurity level in amine systems
Refinery bbl/day 230 000 170 000 58 000 50 000 Annual benefit $30 million $6 million $1 million $2 million

Introduction
Operators of acid gas scrubbing units are continually challenged to maintain and increase throughput as feedstocks change and product specs tighten. Amine systems (scrubbing units employing alkanolamine solvents) have been scrutinised more and more closely over the last 15 to 20 years, because of capacity, throughput

Table 1

www.digitalrefining.com/article/1000267

February 2007 1

included reduced amine losses/consumption/ replacement, reduced anti-foam usage, reduced foaming, reduced filtration costs, reduced heat exchanger fouling, reduced amine unit operating costs, fewer production curtailments, fewer upsets of wastewater treatment plant, record crude, coker, cracker runs, increased overall production, ability to run sourer crude, and increased sulphur production. About 15 years ago, as mobile reclaiming services began to be available, only a few brave operators could be induced to try reclaiming their amine. However, the reclaiming resulted in such dramatically improved operations that they realised that amine reclaiming had to be a necessary part of their future. The previously rarely mentioned HSS became a term that amine system engineers had to know. Replacing traditional bleed and feed (disposal of contaminated amine and replacing it with new amine) are services of ion exchange, distillation and electrodialysis for dissolved salts and degradation products along with filtration and absorption for suspended solids and hydrocarbons.3,4,5 All these technologies have been improved and are more available than ever before as permanent on-site installations, temporary on-site mobile services, and as off-site services. A review of the current state of reclaiming options is overdue. This paper is a review of advances and limitations of reclaiming options organised by contaminant type.

and release acids in the amine regenerator (stripper). The amine system is designed to form salts from the reaction of amine with acid gases H2S and CO2 in the absorber (contactor), and to reverse the process in the stripper, releasing the acid gases to the stripper overhead. Absorber reactions:
R3N + H2S (R3NH)+ + (HS)- [amine plus acid gas salt]

2R2NH + CO2 (R2NH2)+ + (R2NCO2)- [amine plus acid gas salt] {CO2 + H2O H2CO3} R3N + H2CO3 (R3NH)+ + (HCO3)-

[amine plus acid salt]

Regenerator reactions:

(R3NH)+ + (HS)- + Heat R3N + H2S [salt plus heat amine plus acid gas] (R2NH2)+ + (R2NCO2)- 2R2NH + CO2 [salt plus heat amine plus acid gas] (R3NH)+ + (HCO3)- + Heat R3N + H2CO3 {H2CO3 + Heat CO2 +H2O} [salt plus heat amine plus acid gas]

Reclaiming methods
There are fundamentally two approaches to reclaiming contaminated amines: remove the contaminant from the solvent, and remove the solvent with or from the contaminant. A third approach, sometimes used in place of reclaiming, employs additive to negate or cover a particular symptom of a contaminant. Examples of the first approach include ion exchange, electrodialysis, filtration and adsorption. The second approach includes bleed and feed and distillation. The third approach includes addition of caustic, corrosion inhibitors or antifoaming agents.6
Heat stable salts

In other words, the amine system is designed to create, and later break, amine salts. Because the salt breaking is accomplished by heating the amine in the regenerator, these salts can be termed heat labile salts. Other acids similarly form salts with amines. If such salts are not broken with heat and the acid is not released into the overhead of the amine regenerator, these salts are termed HSS. This will occur if the acid is a stronger acid, less volatile and/or less soluble than H2S and CO2. For example, formic acid (HO2CH): Absorber reaction:
R3N + HO2CH (R3NH)+ + (O2CH)[amine plus acid salt]

Regenerator non-reaction:

(R3NH)+ + (O2CH)- + Heat No Change

HSS have become identified as a leading cause of reduced capacity in amine systems. They also contribute to corrosion, increased viscosity and foaming. HSS are salts that do not decompose

Notice that the cation of all these salts is the protonated amine (an amine bound to a hydrogen ion). The complete name of a salt includes the name of the cation and the name of the anion. However, HSS are typically called by the name of the anion. For example, the salt formed by methyldiethanolamine (MDEA) and formic acid is correctly named methyldiethanolammo-

2 February 2007

www.digitalrefining.com/article/1000267

nium formate. MDEA and hydrochloric acid form methyldiethanolammonium chloride. Rather than repeat the awkward cation name (....ammonium), people call out only the name of the anion. Commonly recognised alkanolamine HSS include formate, acetate, propionate, glycolate, oxalate, chloride, thiocyanate, thiosulfate, and sulphate salts. HSS accumulate in the amine, resulting in a loss of acid gas absorbing capacity, because the amine can hold but one hydrogen ion. If additional amine is added to compensate for the capacity loss, water content is sacrificed; viscosity increases, and absorption and stripping efficiencies can suffer. Additionally, HSS contribute to corrosion, which reduces material life and produces solids (corrosion products such as iron sulphide), which can result in fouling, plugging, erosion and foam stabilisation.7 Recommendations for acceptable levels of HSS anions in amine systems range from 500 to several thousand ppm, depending on ion identity and the disposition of the author. Our experience servicing hundreds of amine systems worldwide leads us to recommend, as a general rule, total HSS anion of 5000 ppm or less for the most trouble-free operations. Here are the common approaches to remove HSS from amine solutions.
Bleed and Feed

Neutralisation

The addition of NaOH or KOH, or analogous carbonates, quickly and easily recovers the capacity of the amine. The stronger base (OH-) takes the hydrogen ion away from the alkanolammonium ion, converting it to free amine available again to react with acid, but the formed sodium or potassium salt remains in the amine solution. Neutralisation reaction, hydroxide:
(R3NH)+ + (O2CH)- + NaOH R3N + Na+ + O2CH- + H2O [amine salt plus stronger base free amine plus sodium salt]

Neutralisation reaction, carbonate:

(R3NH)+ + (O2CH)- + Na2CO3 R3N + Na+ + O2CH- + Na+ + HCO3[amine salt plus stronger base free amine plus sodium salts]

Bleed and feed (purging contaminated amine and replacing it with fresh amine) is the most widely practised method of cleaning the amine systems. Bleed and feed does have the advantage of being easiest way of dealing with HSS. This method might not be opposed by your amine supplier. It is more economical if used to maintain very high levels of HSS the higher the salt concentration, the less solvent must be discarded to remove a given amount of salt. Higher salt concentrations lead to more operational problems and shorter mechanical life. Other disadvantages of bleed and feed are well known. There are amine replacement costs and disposal costs, which have risen through the years. Another difficulty with bleed and feed is large quantities of amine can cause difficulties to the site wastewater facilities and can cause wastewater plant upsets. This pump and dump also suffers from poor environmental image.

One disadvantage of neutralisation is the false sense of security that it lends to the operator. While amine capacity is maintained, the amine solution becomes more and more polluted with salts that are not seen by the more common plant analytical methods. These salts likewise contribute to higher solution density and viscosity, reduced surface tension and possible soap formation. Eventually the solution either selfpurges through an upset, or it must be discarded. Neutralisations effect on corrosion has received mixed reviews: some saying it reduced corrosion; others saying it actually increased corrosion rates. Finally, it is easy to add too much caustic, which then creates HSS with the acid gases, causing higher lean loadings and less efficient acid gas scrubbing. Neutralisation is easily misunderstood or wrongfully reputed to be a HSS eliminator or HSS preventative. As the neutralisation reaction shows, it simply converts amine HSS to sodium or potassium HSS. There is no reduction in the salt content of the solution and certainly no prevention of salt formation.
Ion exchange

Ion exchange is a chemically clean and environmentally friendly way to remove HSS and maintain the necessary low levels of HSS in amine systems. Ion exchange literally exchanges a friendly ion for the HSS ion. For example, anion exchange removes the HSS anion, replacing it with hydroxide ion, which frees the amine and returns free amine and water to the amine system.8,9,10

www.digitalrefining.com/article/1000267

February 2007 3

Anion exchange reaction:

Distillation

The virtue of distillation has long been recognised for MEA and DGA. Many MEA and almost all DGA amine systems have permanent thermal reclaimers as an integral part of the amine The HSS anions are later removed from the system. Other amines require vacuum to prevent resin by regeneration with caustic, which thermal degradation upon distillation. Canadian produces biodegradable sodium salts that are chemical reclaimers has provided mobile vacuum friendly to the wastewater treatment system. distillation services for many years. Other Cations, such as sodium, potassium and companies (ChemGroup, Coastal) have offered calcium, are similarly removed from amine distillation reclaiming of amines shipped to their systems by cation exchange. central reclaiming operations. Improvements in While ion exchange seems chemically simple, distillation have reduced amine in waste and the practice of removing HSS from amine systems allowed for permanent units. by ion exchange has presented many technical One important advantage of distillation is that and operational challenges. Several have reported it has an economic advantage when dealing with the belief that it will not work effectively for very high concentrations of HSS. Secondly, there amine reclamation, based on actual attempts. are low quantities of waste generated, and it has MPR Services, on the other hand, has been low water and chemical consumption (close to 1 providing successful amine ion exchange reclaim- mole caustic per mole HSS). Distillation works ing services worldwide since 1991. better with amines with low boiling points. The The advances in ion exchange have lead to major disadvantage of distillation is the energy reduced chemical and water consumption. consumption needed to vapourise and distill over Caustic utilisation 15 years ago was typically 9 the amine solution. Distillation sends the most to 40 moles NaOH per mole HSS, now it is amine to waste of the discussed reclaimer methmore like 3 to 5 moles. NaOH per mole HSS ods. It also generates a concentrated waste that and recent advances have reduced that to just is considered potentially hazardous in many over 1 mole NaOH per mole HSS anion. Water jurisdictions. The waste contains amines and requirements, depending on the application, amine degradation products, as well as salts and can now be about two-thirds to one-fifth of the other contaminates. Distillation has poor water demand 15 years ago. Mobile and perma- economics for maintaining low concentrations of nent ion exchange units have become HSS, because such a large volume of solvent available throughout the world. In addition to must be distilled to remove a small amount of efficiently removing HSS, another primary salts. advantage of ion exchange is that its waste is DGA reclaimers are actually designed to biodegradable. convert a degradation product (BHEEU) back to Ion exchange has the advantage of being the useful DGA. A properly operated, clean (free of most economical method by which to maintain other contaminants) DGA reclaimer should low levels of contaminates. Particularly in gas ideally operate indefinitely. However, HSS and plants, where salt incursion rates are low, ion non-volatile impurities accumulate in the DGA exchange should be the most economical way to reclaimer, which can upset the BHEEU convertreat low-level contaminants like chlorides and sion. The accumulation of HSS in the DGA amino acids. Ion exchange has lower energy reclaimer can lead to increased operating needs than distillation and electrolysis cleaning temperatures and the formation of another services, generates larger, more dilute volumes degradation product, morpholine.11 To bring the of waste, and requires more water. Poorly reclaimer back to correct operation, the HSS and designed and/or operated ion exchange systems other contaminants must be purged from the have caused significant amine losses and sodium reclaimer by dumping its contents, which wastes slippage into the amine. Better-designed ion good DGA and the DGA trapped in BHEEU. exchange systems, such as MPRs HSSX process, Increased HSS incursion will increase reclaimer lose no significant amounts of amine and slip no dumping frequency, which wastes more amine. sodium. It would be better to keep the amine free of HSS
(R3NH)+(O2CH)- + (Resin)+(OH)- R3N + (Resin)+(O2CH)- + H2O [Amine salt plus Resin-base free amine plus Resin-salt]

4 February 2007

www.digitalrefining.com/article/1000267

by means of ion exchange, thus avoiding reclaimer problems. The DGA and MEA thermal reclaimers are periodically emptied of the accumulated salts, which are sent to waste. Very commonly, the reclaimer bottoms have high amine content, causing the reclaimer to be more of a bleed and feed device. Table 2 shows the results of a survey of the amine/HSS ratio in several amine systems and their reclaimer bottoms. Ideally, the amine/ HSS ratio was much, much lower in the reclaimer bottoms than in the system, so less amine would be wasted via reclaimer bottoms than via direct bleed and feed. In only about one-third of the cases is the amine loss in the reclaimer less than half the loss that bleed and feed would have caused. MEA reclaimers also collect, and even cause formation of, amides and ureas, each of which entraps an MEA molecule. Thus, the total amine lost in thermal reclaimers is much worse than is shown in Table 2. Table 3 shows total amine lost per mole of HSS, which is the sum of free amine, amides and ureas. Based on amine alone, Reclaimer D seems to be the least wasteful operation, but it is actually the most wasteful because of the high amount of amides and ureas.
Electrodialysis units (EDU)

Thermal reclaimers waste good amine


System Amine Free amine/HSS mol/mol mol/mol MEA MEA MEA 17 MEA MEA 82 MEA MEA 3 MEA 3 MEA 5 MEA 4 MEA 5 MEA 6 MEA 3 MEA 11 MEA 23 DGA DGA 62 29 Reclaimer bottoms Free amine/HSS 50 10 3 1 2 26 4 2 6 4 5 3 4 2 1 77 44

Table 2

The electrodialysis units have become more available and they have improved with new membrane technologies. Electrodialysis providers have claimed a greatly reduced need to neutralise HSS before removal of anions.12 Also, electrodialysis providers are able to remove HSS salts to lower levels with less amine waste than in previous years, and EDU units can remove thiosulfate impurities better than ever before. Membrane selection and maintenance is critical to the success of the EDU. The various membranes have different selectivities for different ions, so one may see some ions removed and others not. Electrodialysis has lower energy demands than vacuum distillation. EDUs have an advantage of lower chemical and water usage than ion exchange. One primary difficulty with Electrodialysis technology through the years has been dealing with solids. It is recommended that EDU needs a 1 micron pre-filter. Another difficulty with electrodialysis is amine levels in the waste increase when going to low HSS endpoints. Often a trade-off has been observed between

anion removal efficiency and amine losses; ie, reduce amine losses by reducing the efficiency of removal of anions from the amine. One performance example allowed 70% of the anions to slip past the membranes (stay in the amine solution). Fouling of membranes has historically been a major cause of downtime and membrane expense. Recent advances have made this less of a problem. EDUs also have much higher power consumption than ion exchange, and EDUs generate more waste than vacuum distillation. Salt concentration in the waste runs from 3 to 20 times the salt concentration in the amine.

Amino acids
Amino acids have received considerable attention recently due to their corrosive nature at
Thermal reclaimers waste amine as amine, amides and urea
Amine system A Amine/HSS, mol/mol 3.3 (Amide + urea)/HSS, mol/mol 0.2 (Total amine loss)/HSS = (amine + amide + urea)/HSS mol/mol 3.4 B 3.6 0.7 4.3 C 2.1 1.4 4.5 D 1.2 4.4 5.6

Table 3

www.digitalrefining.com/article/1000267

February 2007 5

relatively low concentrations.13,14,15,16 Bicine {(HOCH2CH2)2NCH2CO2H} in MDEA and DEA systems and Hydroxyethylsarcosine (HES) {(HO CH2CH2)N(CH3)(CH2CO2H)} from MMEA are currently reportable by many amine analysis laboratories. Bicine is a strong complexer of iron, capable of holding iron in solution in the presence of some H2S in lean amine solutions, so it is expected to contribute to corrosion. Based on laboratory corrosion studies, bicine has been recommended to be kept as low as 250 ppm in amine systems17 especially where H2S levels are low. Corrosion in gas plant amine has been clearly traced to bicine in the 1000 to 4000 ppm range.14 In a collection of 1739 amine samples from 273 different gas treating plants, 825 had more than 100 ppm bicine.18 Because there have not been an extraordinary number of reports from accounts of active corrosion these authors doubt the importance of bicine corrosivity. As bicine and other amino acids are found in more amine systems, we will certainly hear more about amino acid corrosivity. The chemical pathways for forming bicine in amine systems has not been determined. Proposed pathways include: Reaction of cyanide with formaldehyde DEA with Glyoxal Direct degradation of DEA with oxygen Disproportion reaction of MDEA to TEA and further oxidation of TEA to Bicine Reaction of cyanide with imide of MDEA (from DEA or MDEA) Thiosulfate (S2O3) assisted reaction with MDEA or DEA (observed in tail gas units.
Bleed and Feed

Because bicine can complex other cations, it has been suggested that sodium or potassium from caustic addition (neutralisation of amine HSS and amino acids) might divert bicine from iron complexation. This theory was supported by calculations of Bosen and Bedell.18 Our literature search led us to complexation constants, which, when applied to the Bosen and Bedell theoretical calculations, yielded clear evidence that bicine strongly enhances iron solubility in H2S systems, and that this enhanced solubility is insignificantly affected by the presence of very high concentrations of sodium or potassium. Bicines effect on the solubility of iron in CO2 systems is orders of magnitude higher.19 Sodium and potassium cannot be relied upon to significantly reduce bicine complexation of iron. Field experience in gas plants and refineries attests to amino acid corrosivity and ineffectiveness of caustic addition. A Texas gas plant identified bicine as the root cause of amine system corrosion, correlated dissolved iron increases and decreases with bicine increases and decreases, but found no reduction in corrosion attack upon neutralisation by caustic addition. A Gulf Coast Refinery added caustic to the amine solution to control escalating bicine levels. No impact on measured corrosion rates was observed, but unit performance continued to deteriorate. A Gulf Coast gas plant encountered escalated corrosion rates and high bicine levels. Sodium was added in an effort to control the corrosion. Minimal impact was observed.
Ion exchange

Pump and dump is not normally used to lower a bicine contamination because of the poor economics of addressing a low concentration impurity by throwing away amine.
Neutralisation

Although claims have been made and rationale published that neutralisation helps to reduce corrosion by amino acids operator testimony, further theoretical scrutiny shows neutralisation to be of no value for masking bicine corrosion. Fully de-protonated amino acid is stronger in chelating of iron than partially de-protonated, so caustic neutralisation of bicine serves only to assure more of the bicine is in its strongest form.

MPRs HSSX ion exchange process has had considerable success in bicine removal. Ion exchange can work well for bicine removal, especially when addressing low-level bicine impurities.14,20,21 Other ion exchange providers have had difficulty in removing bicine due to their process conditions that result either in poor bicine removal or adding sodium to amine system.
Distillation

It has been suggested that distillation can remove amino acids, but there has been no identifiable instance in the literature were distillation was used to specifically remove amino acids.22 This may due to the fact the distillation is at its best with high-concentration impurities and most

6 February 2007

www.digitalrefining.com/article/1000267

bicine applications begin at relatively low concentrations (1 wt% or less) and are seeking to reduce bicine to 250 ppm or lower.
EDU

with fresh amine works to remove amides, but has the same advantages and disadvantages that were discussed for HSS.
Neutralisation

Electrolysis has shown some positive results, but amino acids removal is still being developed.

Amides
Primary and secondary amine form amides with carboxylic acids. For example, MEA and formic acid form an MEA formamide called FormylMEA (also FMEA or MEAF). Similarly for DEA, DIPA, DGA, etc. Other amides such as acetamides (eg, Acetyl-DEA from DEA and acetate) may also form. For simplicity, the following discussion mentions only formamides, but it applies to other amides. Formation of formamides results in a loss of one mole of useful amine per mole of formamide. The equilibrium formation of these formamides may be depicted as follows:
AmineH+ + Formate- Formyl-amine + H2O

Neutralisation removes protonated amine from the equilibrium reaction by raising the pH, and drives the amide to amine and formate. Thus, while caustic addition might increase the available amine concentration a little, neutralisation replaces the relatively non-corrosive formamide with corrosion-enhancing formate.
Ion exchange

Ion exchange removes the formate ion from the equilibrium reaction, and drives the equilibrium to amine and formate. Ion exchange is extremely selective, removing only the formate, none of the formamide. Formamide can all be converted to useful amine. For example, one refiner identified 90 000 lb of new DEA from formamide conversion after removing formate and other HSS from the amine system by ion exchange.
Distillation

Temperature, time, pH and concentration affect the formation of amides. Since the first two factors are usually fixed in the system, attention must be given to concentration. There is an equilibrium relationship between formate and amine formamides in primary or secondary amines. The molar ratio of formamide to formate varies with amine type and degree of contamination, with higher ratios typically seen at higher contaminant concentrations. Formamides have been seen in operating amine systems from less than 1 wt% to 15 wt% and higher. Of the common alkanolamines, the formamideto-formate ratio is highest in DIPA, typically around 2:1. The ratio in DEA is typically about 1:1. In an operating amine system, formamides may be converted back to useful free amine by removing the formate from the amine solution. As formate concentration is reduced, the equilibrium causes the formamide to convert back to protonated amine and formate. Further removal of formate results in further reduction in formamide concentration.
Bleed and feed

Because of the dehydrating aspect of distillation, amides can actually increase during the reclaiming process. Additional good amine thus becomes trapped in the reclaimer bottoms (see Table 3 and attendant discussion of thermal reclaiming) and is wasted. This can cause difficulties for wastewater treatment facilities. Permitted the requisite time and operating skill, however, vacuum distillation and thermal reclaiming processes should be able to recover amine from amides. Commonly, however, amides remain in the bottom of the still and are thrown away, representing lost amine, which is costly to discard and to replace.
EDU

Electrodialysis removes the formate ion from the system, and the equilibrium consumes formamides to form amine and formate. Electrodialysis has similar advantages and disadvantages when dealing with amides as it does with HSS.

Oxazolidones
Example: 3-(2-hydoxypropyl)-5-methyl-1,3oxazolidin-2-one (HPOZD). Oxazolidones are particularly problematic in DIPA and Sulfinol-D systems, where they can build up in concentra-

Purging contaminated amine and replacing it

www.digitalrefining.com/article/1000267

February 2007 7

Oxazolidone conversion to amine by OXEX process


Description Commercial Job 1 Oxazolidone Starting point, wt% 36.08 Oxazolidone Ending point, wt% 4.34 % Conversion of Oxazolidone on a per batch basis >95% DIPA in system at start of job, wt% 37.57 DIPA in system at end of job, wt% 53.58 Net absolute increase in DIPA Concentration, wt% 16.01 Commercial Job 2 22.84 6.20 >95% 29.57 42.86 13.29

Table 4

tion and reduce capacity. Oxazolidones could also form in DEA and MEA, but are not commonly present at significant concentrations. Pump and dump can be used, but it is a very expensive way of dealing with oxazolidones, especially in Sulfinol-D systems. Neutralization, ion exchange and EDU are not considered effective ways of dealing with oxazolidones.
Distillation

HEEU (Hydroxyethylethylenediamine urea) found in MEA HEED (Hydroxyethylethylenediamine) found in MEA BHEEU (N,N-bis(hydroxyethoxyethyl)urea found in DGA THEED (Tris-Hydroxyethylethylenediamine) found in DEA Bis-HEP (Bis-hydroxyethylpiperzine) found in DEA DIPA/MIPA DIPA/DIPA dimers found in DIPA2 Diamines and ureas reduce the capacity of amine solutions, and can be responsible for corrosion, increased viscosity and reduced water content.
Bleed and feed

Pump and dump have been used successfully when treating diamines and ureas. Pump and dump has the advantages and disadvantages discussed in the HSS section.
Neutralisation

Oxazolidones can be separated from the amine by distillation. However, in Sulfinol-D solutions, there may be some difficulty separating the sulfolane from the oxazolidone. Because oxazolidones contain the amine molecule, there is the additional cost of having to replace the amine that was tied up as the oxazolidone. The waste is a problem, because the wasted oxazolidone contains the ammonia nitrogen functionality.

There are no known examples of neutralisation being effective in treating diamines and ureas.
Ion exchange

OXEX process The advantage of the OXEX process (patent pending) is that it converts the oxazolidones back into useful amine.21 The waste is easily discarded to the wastewater treatment facilities because the waste contains only water and carbonate and sulphate salts. Recent advances in the OXEX process have led to reduced costs and improved throughput. The conversion efficiency has been greater than 95% for the batch process. The improved process has been proven in the lab and in two commercial efforts, as shown in the Table 4. It is more economical than distillation or pump and dump.

Ion exchange is not an effective way of removing diamines and ureas. However, field results indicate that continual operation of ion exchange to control HSS in refinery DEA systems prevents further formation of THEED. It is suspected that this is a side effect of the improved regenerator conditions resulting from operating with cleaner amine.
Distillation

The value of thermal reclaimers for MEA and DGA is well known. Distillation of other amines has been successful in removing high concentrations of diamines and ureas. The advantages and disadvantages of distillation for treating diamines and ureas are similar to the advantages and disadvantages of distillation for HSS removal discussed above.
EDU

EDU is not an effective way of removing diamines and ureas.

Diamines and ureas


Examples of diamines and ureas are:

Solids
Solids normally provide different types of

8 February 2007

www.digitalrefining.com/article/1000267

problems for amine operators. Solids are a heterogeneous phase. Solids can settle out or combine with hydrocarbons or anti-foam and coat the internal components of the amine system. The shoe polish that coats the internal amine system leads to filter plugging, tray plugging and reduced thermal transfer.23 Another difficulty with solids is they can contribute to corrosion by mechanical wear that erodes the internal surfaces. In certain circumstances, it has been shown that solids can stabilise foaming. If the solids contain considerable iron sulphide, the iron sulphide can represent a fire hazard when servicing the amine system. Under normal conditions, pump and dump, neutralisation, ion exchange, distillation and EDU are not used to deal with solids.
Size exclusion filters

attracted to the media.24 This means SSX media normally does not plug, there is a low pressure drop and it can remove particles to less than 1 micron. The media is regenerated with water and works well on rich or lean side treating. It also works well for refineries where the oily wastewater is handled easily. The process rarely plugs. The disadvantage of this technology is that it may not remove 100% of particles per pass.

Hydrocarbons
Hydrocarbons are associated with plant upsets and are frequently blamed as a source of foaming. Hydrocarbons and anti-foam combine with solids, which may result in plugging. Hydrocarbons are a poison to Claus catalysts. They are not normally addressed with pump and dump, neutralisation, ion exchange, distillation or EDU. Most amine systems have a permanently installed phase separator (knock-out drum) to deal with hydrocarbons that are not miscible with the amine solution. Hydrocarbons that make it past the phase separator require a reclaiming method.
Activated carbon

Almost always solid removal is done with permanent units using size exclusion filtering. Advances in filters include an increased variety of easierto-use filtering technology. The vast majority of filtering media is disposable (back washable media is available, but this media requires water). The advantage of disposable exclusion filters is that they are easy to use and readily available worldwide from many suppliers. However, they can require frequent replacements in dirty systems. The filters do not remove particles below rated particle size, and the consumable nature of filters can make for expensive purchase and disposal costs. Another difficulty is the potential for a fire hazard form iron sulphide. There are also labour costs and personnel issues involving H2S during filter change-outs. All too often, filters are bypassed during operations to avoid dealing with a plugged filter.
SSX process

Amine systems use a tank filled with activated carbon to address dissolved and entrained hydrocarbons. In practice, activated carbon bed performance suffers from the problems of being undersized and neglected. The activated carbon also needs to be regularly replaced, leading to purchase and disposal costs, as well as the labour required. Monitoring the condition of an activated carbon filter is also difficult.
HCX process

SSX technology is a method where the solids are

HCX technology uses a surface attraction of hydrocarbon that removes immiscible, entrained and dissolved hydrocarbons from the amine systems.25 The advantage is the HCX media

Hydrocarbon content of amine - before and after HCX process installation


Refinery location Before HCX HC ppm Midwest 100-3000 Midwest 200-400 Gulf Coast 2000-6500 Middle East 700 After HCXHC ppm 1-10 2-30 1-30 2-15 Operation time >5 years >4 years >2 years >2 years Operator comments Smoother operations; sulphur plant happy 2.6 MM$ to bottom line in first year Amine losses greatly reduced More efficient than prior installation

Table 5

www.digitalrefining.com/article/1000267

February 2007 9

normally is back washed about every two to five days to regenerate its surface. This technology works well for refineries where the oily wastewater is handled easily.

Foam abatement
Foaming in amines systems cause system upsets that lead to loss production and amine losses. Foaming is caused by an impurity or impurities that act as surfactants in the amine system, which allows the stabilisation of the gas in liquid dispersion. Foaming has been attributed to a number of contaminants such as hydrocarbons (polar and non-polar), HSS and solids.26,27,28
De-foamers

effective for high incursion rates. Hydrocarbon and solid removal units are considered important enough to be permanent units in almost all amine systems. The disadvantages of permanent units are their capital costs.
Mobile units

There is a wide variety of anti-foaming or defoaming agents available. These additives are believed to break the foam by being a heterogeneous droplet or solid enter entering the foam bubble and weakening the wall until the bubble ruptures.29 There have been advances in choices, effectiveness and stability of these de-foaming additives. The advantages of de-foaming agents are their ease of use and low initial capital expense. Their primary disadvantage is that they do not remove the impurities that cause the foaming in the amine system. They can give operations a false sense of security and hide the underlying problem/impurity, which could lead to a cycle of repeated foaming. Also, de-foaming additives can become inactive at high concentrations and fail break the foam.
SigmaPure

Mobil units are probably more economical for low incursion rates where annual or longer cleaning events are acceptable. Mobile reclaiming can be called upon to deal with emergencies and upset conditions, such as typical of HSS formation in tail gas units, sudden hydrocarbon transfers into circulating amine, and thermal or mechanical events shaking loose large amounts of solids. Mobile units can be used to demonstrate the effectiveness of a new technology.
Offsite treatment

Transporting contaminated amine to an offsite reclaiming centre can be less intrusive than mobile reclamation, but is much more hassle than permanent onsite reclamation units. Offsite reclaiming is a variation of bleed and feed, regardless of the method of reclaiming at the offsite centre. The bleed is the same; the feed is your own amine after reclaiming. Thus, offsite reclamation is best for maintaining high concentrations of impurities. The high contamination conditions are harmful to the amine system and to operations. Other disadvantages of offsite treatment are the shipping costs and risks.

Summary and conclusion


A variety of reclaiming options are now available to the amine system operator, whereby troublesome contaminants can be removed. These options have matured and improved over the last 15 years and are available as mobile services or permanent installations throughout the world. A comparative summary of these options is presented in Appendix A. Benefits of reclaiming have been widely demonstrated, and it is now commonly accepted that amine system operational problems can be reduced and efficiencies increased by keeping the amine solution clean and free of contaminants.
References 1 Wissbaum R J, Sulfur Recovery Outlook to 2025, 2006 Vail Sulfur Symposium. 2 Smit C J, van Heeringen, van Grisven P R A, Degradation of

D-Foam with the SigmaPure cleaning system has a unique method of effectively removing the foaming agents and any impurities that travel with the foam.28,30 The system intentionally causes controlled foaming of a slipstream of amine outside of the amine unit. Amine is drained from the foam, and the foam is carried over into a waste container. The amine is returned to the customer with the foam-causing contaminates removed.

Permanent units vs mobile units vs offsite treatment


Permanent units

Permanent units are ideal for keeping contaminate at low levels continuously and are more cost

10 February 2007

www.digitalrefining.com/article/1000267

Comparison of methods for removal of HSS and degradation products


Ion exchange Applicability Removal of Ionised impurities Operation principle Ions captured by ion exchange resin Distillation Removal of solids and non-volatile species Vapourisation of volatile species (water, amine, etc) from salts and degradation products Electrodialysis Removal of ionised impurities Ions removed by electrodialysis

Limitations Cannot remove non-ionic species Energy intensive; most amines Cannot remove non-ionic species; need vacuum membranes selection and durability Forte Best option for low conc. salts Waste products Dilute aqueous stream containing removed ions and excess regeneration chemicals Volume of wastes Amine recovery High to moderate >99% (some do 95 to 98%) High conc. salts and degradation products Amine conc remains the same

Reclaimer bottoms,containing Aqueous brine containing removed salts, non- volatile organics, ions and some amine. Normally hazardous waste Low 95-85% Moderate 98% Lean, cool, hydrocarbon-free, particle-free amine HSAS neutralised DC power; chemicals 1 mol/mol

Amine feed requirements Lean cool amine HSAS neutralised Special requirements Regeneration chemicals as low as 1 mol/mol (often more) Operating mode Batch or on-line Fuel gas or high temp heat source; chemicals 1 mol/mol Batch or on-line

Batch or on-line

Unit availability Permanent and mobile units available

Mobile units available Permanent and mobile units (many DGA and MEA units available have permanent thermal reclaimers)

Appendix A: Table A1
Amine Solvents and the Relation with Operational Problems, 2002 Laurence Reid Gas Conditioning Conference,197. 3 Kohl A, Nielsen R, 1997, Gas Purification, 5th ed, Houston, TX, Gulf Publishing, Ch 3. 4 Keller A E, Cummings A L, Nelsen D K, Amine purification system to increase crude processing, PTQ, Spring 2003. 5 Burns D, Gregory R A, The UCARSEP Process for On-Line Removal of Non-Regenerable Salts from Amine Units, 1995 Laurence Reid Gas Conditioning Conference. 6 Abdi M A, Golkar M M, Meisen A, Improve Contaminate Control in Amine Systems, Hydrocarbon Processing, Oct 2001, 102-C. 7 Keller A E, Cummings A L, Grime Doesnt Pay, Brimstone 2004 Sulfur Recovery Symposium Vail, Colorado. 8 Shao J, Lu G, Ye M, Removal of Heat Stable Sates - As Solution to Amine Plant Operational Problems, Chemical Engineering in Petroleum and Natural Gas Journal, China, Dec 2002. 9 Jouravleva D, Davy P, Sheedy M, Impact of Continuous Removal of Heat Stable Salts on Amine Plant Operation, 2000 Laurence Reid Gas Conditioning Conference. 10 Coberly S H, Laven T H, Cummings A L, Amine Heat Stable Salt Removal from Type II Anion Exchange Resins, US Patent 5788864 and reference to patents therein, 1998. 11 Harruff L G, Saudi Arabian Experience with DGA Units and Related Sulfur Plants, 1998 Laurence Reid Gas Conditioning Conference, 76. 12 Parisi P, Bosen S, Amine Reclamation with Minimal Operational Impact through Electrodialysis, 2006 Laurence Reid Gas Conditioning Conference, 301. 13 Cummings A L, Veatch F C, Keller A E, Corrosion and Corrosion Control Methods in Amine Systems Containing H2S, paper 97341, 1997 NACE International. 14 Howard M, Sargent A, Operating Experience at Duke Energy Field Services Wilcox Plant with Oxygen Contamination and Amine Degradation, 2001 Laurence Reid Gas Conditioning Conference. 15 Pearson H; Shao J, Norton D, Dandekar S, Case Study of Effects of Bicine in CO2 Only Amine Treater Service, 2005 Laurence Reid Gas Conditioning Conference, 107. 16 Critchfield J E, Jenkins J L, Evidence of MDEA degradation in tail gas treating plants, PTQ, Spring 1999, 87-95. 17 Rooney P C, Bacon T R, DuPart M S, Effect of Heat Stable Salts

www.digitalrefining.com/article/1000267

February 2007 11

Comparison of methods for removal of solids, hydrocarbons, and foaming agents


Mechanical filtration Applicability Removal of particles and sludge; many choices available Operation principle Size exclusion filtration; some regenerable SSX Activated carbon HCX D-Foam SigmaPure Removal of particles Removal of high Will remove broad Removes foaming and sludge, can molecular weight, range of organics agents remove particles polar organics, and anti-foam smaller than 1 and anti-foam, micron many choices available Attraction to media; Adsorption regenerated with (usually with water filtration) Removes only particles; may not remove 100% particles per pass Attraction to media; Expulsion of foam regenerated with hot water

Limitations Removes only particulate matter; often requires media change-out, particle size removal depends on filter rating Waste products Filter sludge, filter bag, cartridges, normally hazardous solid waste Volume of wastes Amine recovery Amine feed requirements Special requirements Operating mode Unit availability Low to high High

Require particle filtration before and after

Aqueous waste with Spent carbon, Oily water, normally Foaming agents and solids and normally handled in plant small amounts of hydrocarbons hazardous solid wastewater amine; potentially normally handled waste facilities hazardous in plant wastewater liquid waste facilities High High Low High High High Can be used on on lean or rich amine (does not need to be pre-filtered) Very Low High Can be used on lean or rich amine (does not need to be pre-filtered) Nitrogen or fuel gas for purge gas

None, but caution None, SSX can be Pre-filtered lean has to be used for safely used on lean amine H2S exposure during or rich amine rich side filter solutions change-outs Periodic clean-out Water for required; if regeneration regenerable require air, nitrogen, water, etc Continuous Normally in permanent units Continuous Permanent or mobile units

Periodic clean-out Hot water for required regeneration

Continuous Normally in permanent units

Continuous Permanent or mobile units

Continuous Mobile units


Appendix A: Table A2

on Solution Corrosivity of MDEA-Based Alkanolamine Plants. Part III, 1997 Laurence Reid Gas Conditioning Conference, 12. 18 Bosen S F, Bedell S A, The relevance of Bicine in the Corrosion of Amine Gas Treating Plants, 2004 Laurence Reid Gas Conditioning Conference, 31 [also paper No. 04481, NACE Corrosion 2004]. 19 Cummings A L, Waite S W, Nelsen D K, Corrosion and Corrosion Enhancers in Amine Systems, 2005 Brimstone Sulfur Recovery Symposium Alberta, Canada. 20 Lawson G L, Cummings A L, Mecum S, Amine Plant Corrosion Reduced by Removal of Bicine, 2003 Gas Processors Association Annual Convention, San Antonio, TX.

21 Cummings A, Street D, Lawson G, Contaminants and their Effects on Operations Using Solvents, World Refining, Oct 2003. 22 Jenkins J L, Haws R, Understanding Gas Treating Fundamentals, PTQ, Winter 2001-2. 23 Spooner B, Iron Sulphides - Friend or Foe, 2006 Laurence Reid Gas Conditioning Conference, 109. 24 Keller A E, Veatch F C, Cummings A L, Thompsen J C, Severson R A, Removal of Iron Sulfide Particles from Alkanolamine Solutions, US Patent 5190662, 1993 25 Cummings A L, Regenerable Hydrocarbon Filter, US Patent 6416670, 2002. 26 Pauley C R, Hashemi R, Caothien S, Analysis of Foaming

12 February 2007

www.digitalrefining.com/article/1000267

Mechanism in Amine Plants, 1989 Laurence Reid Gas Conditioning Conference. 27 Pauley C R, Face the Facts about Amine Foaming, Chemical Engineering Progress, July 1991. 28 von Phul S, Sweetening Process Foaming and Abatement, 2001 Laurence Reid Gas Conditioning Conference. 29 von Phul S, Antifoam - What is it? How Does It Work? Why Do They Say to Limit Its Use?, 2005 Laurence Reid Gas Conditioning Conference, 231. 30 von Phul S, Sweetening Process Foaming and Abatement Part II: Case Studies, 2002 Laurence Reid Gas Conditioning Conference, 9.

Links
More articles from: MPR Services Inc More articles from the following categories: Carbon Capture & Storage Delayed Coking Corrosion/Fouling Control Fluid Catalytic Cracking Gas Processing & Treatment Heavy Crudes LNG/GTL Mass Transfer & Separation Petrochemicals Power Generation Reforming

www.digitalrefining.com/article/1000133

PTQ Q3 2006 13

You might also like