Scribd
Upload
413 views2 pages

Cause Value

The document defines various cause codes for radio network layer failures, transport layer failures, NAS protocol failures, and other protocol and miscellaneous failures during wireless communication procedures. It also provides a table converting between decibel-milliwatts (dBm) and watts as a measure of signal strength.

Uploaded by

Ranu25
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
413 views2 pages

Cause Value

The document defines various cause codes for radio network layer failures, transport layer failures, NAS protocol failures, and other protocol and miscellaneous failures during wireless communication procedures. It also provides a table converting between decibel-milliwatts (dBm) and watts as a measure of signal strength.

Uploaded by

Ranu25
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

>Radio Network Layer Cause INTEGER (RAB pre-empted(1) Trelocoverall Expiry(2) Trelocprep Expiry(3) Treloccomplete Expiry(4) Tqueuing Expiry(5)

Relocation Triggered(6) Unable to Establish During Relocation(8) Unknown Target RNC(9) Relocation Cancelled(10) Successful Relocation(11) Requested Ciphering and/or Integrity Protection Algorithms not Supported(12) Conflict with already existing Integrity protection and/or Ciphering information (13) Failure in the Radio Interface Procedure(14) Release due to UTRAN Generated Reason(15) User Inactivity(16) Time Critical Relocation(17) Requested Traffic Class not Available(18) Invalid RAB Parameters Value(19) Requested Maximum Bit Rate not Available(20) Requested Maximum Bit Rate for DL not Available(33) Requested Maximum Bit Rate for UL not Available(34) Requested Guaranteed Bit Rate not Available(21) Requested Guaranteed Bit Rate for DL not Available(35) Requested Guaranteed Bit Rate for UL not Available(36) Requested Transfer Delay not Achievable(22) Invalid RAB Parameters Combination(23) Condition Violation for SDU Parameters(24) Condition Violation for Traffic Handling Priority(25) Condition Violation for Guaranteed Bit Rate(26) User Plane Versions not Supported(27) Iu UP Failure(28) TRELOCalloc Expiry (7) Relocation Failure in Target CN/RNC or Target System (29) Invalid RAB ID(30) No remaining RAB(31) Interaction with other procedure(32) Repeated Integrity Checking Failure(37) Requested Request Type not supported(38) Request superseded(39) Release due to UE generated signalling connection release(40) Resource Optimisation Relocation(41) Requested Information Not Available(42) Relocation desirable for radio reasons (43) Relocation not supported in Target RNC or Target system(44) Directed Retry (45) Radio Connection With UE Lost(46) RNC unable to establish all RFCs (47) Deciphering Keys Not Available(48) Dedicated Assistance data Not Available(49) Relocation Target not allowed(50) Location Reporting Congestion(51) Reduce Load in Serving Cell (52) No Radio Resources Available in Target cell (53) GERAN Iu-mode failure (54) Access Restricted Due to Shared Networks(55)

Incoming Relocation Not Supported Due To PUESBINE Feature(56) Traffic Load In The Target Cell Higher Than In The Source Cell(57))

>Transport Layer Cause Signalling Transport Resource Failure(65) Iu Transport Connection Failed to Establish(66))

>NAS Cause User Restriction Start Indication(81) User Restriction End Indication(82) Normal Release(83)) Value range is 81 - 96.

>Protocol Cause Transfer Syntax Error(97) Semantic Error (98) Message not compatible with receiver state (99) Abstract Syntax Error (Reject) (100) Abstract Syntax Error (Ignore and Notify) (101) Abstract Syntax Error (Falsely Constructed Message) (102)) >Miscellaneous Cause O&M Intervention(113) No Resource Available(114) Unspecified Failure(115) Network Optimisation(116)) >Non-standard Cause () Value range is 129 - 256. Cause value 256 shall not be used. " ================================================================================ === dBm 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Watts 1.0 mW 1.3 mW 1.6 mW 2.0 mW 2.5 mW 3.2 mW 4 mW 5 mW 6 mW 8 mW 10 mW 13 mW 16 mW 20 mW 25 mW 32 mW 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 dBm Watts 40 mW 50 mW 63 mW 79 mW 100 mW 126 mW 158 mW 200 mW 250 mW 316 mW 398 mW 500 mW 630 mW 800 mW 1.0 W 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 dBm Watts 1.6 W 2.0 W 2.5 W 3.2 W 4.0 W 5.0 W 6.3 W 8.0 W 10 W 13 W 16 W 20 W 25 W 32 W 40 W dBm -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 .8 .6 .5 .4 .3 .3 .2 .2 .1 .1 Watts(mW)

You might also like