Scribd Logo
Upload

Welcome to Scribd!

  • 156 views

    2-Channel Preamplifier For Car Stereo: Package Dimensions Features

    Uploaded by

    vetchboy
    The LA3161 is a 2-channel preamplifier integrated circuit for car stereo applications. It has two on-chip preamplifiers with good ripple rejection from an on-chip voltage regulator and requires a minimum number of external parts. It has low noise and is packaged in an 8-pin SIP package for easy mounting. The LA3161 has specifications for voltage gain, output voltage, total harmonic distortion, input resistance, equivalent input noise voltage, crosstalk, and ripple rejection. Sample application circuits show how to use external capacitors and resistors to implement a preamplifier for car stereo with NAB equalization characteristics.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    2-Channel Preamplifier For Car Stereo: Package Dimensions Features

    Uploaded by

    vetchboy
    156 views7 pages
    The LA3161 is a 2-channel preamplifier integrated circuit for car stereo applications. It has two on-chip preamplifiers with good ripple rejection from an on-chip voltage regulator and requires a minimum number of external parts. It has low noise and is packaged in an 8-pin SIP package for easy mounting. The LA3161 has specifications for voltage gain, output voltage, total harmonic distortion, input resistance, equivalent input noise voltage, crosstalk, and ripple rejection. Sample application circuits show how to use external capacitors and resistors to implement a preamplifier for car stereo with NAB equalization characteristics.

    Original Title

    audio_la3161_spec_en

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The LA3161 is a 2-channel preamplifier integrated circuit for car stereo applications. It has two on-chip preamplifiers with good ripple rejection from an on-chip voltage regulator and requires a minimum number of external parts. It has low noise and is packaged in an 8-pin SIP package for easy mounting. The LA3161 has specifications for voltage gain, output voltage, total harmonic distortion, input resistance, equivalent input noise voltage, crosstalk, and ripple rejection. Sample application circuits show how to use external capacitors and resistors to implement a preamplifier for car stereo with NAB equalization characteristics.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    156 views7 pages

    2-Channel Preamplifier For Car Stereo: Package Dimensions Features

    Uploaded by

    vetchboy
    The LA3161 is a 2-channel preamplifier integrated circuit for car stereo applications. It has two on-chip preamplifiers with good ripple rejection from an on-chip voltage regulator and requires a minimum number of external parts. It has low noise and is packaged in an 8-pin SIP package for easy mounting. The LA3161 has specifications for voltage gain, output voltage, total harmonic distortion, input resistance, equivalent input noise voltage, crosstalk, and ripple rejection. Sample application circuits show how to use external capacitors and resistors to implement a preamplifier for car stereo with NAB equalization characteristics.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 7

    Ordering number:ENN573F

    Monolithic Linear IC

    LA3161

    2-Channel Preamplifier For Car Stereo

    Features Package Dimensions


    • On-chip 2 preamplifiers. unit:mm
    • Good ripple rejection owing to on-chip voltage regula- 3016B-SIP8
    tor.
    [LA3161]
    • Minimum number of external parts required.
    • Low noise.
    • 8-pin SIP package facilitating easy mounting. 22.3
    3.0
    • Pin-compatible with LA3160. 1.5

    0.51 min
    5.7 max
    1.0
    4.8

    3.2
    1 8

    2.26 2.54 0.5 1.3 0.25


    1.35

    Specifications SANYO : SIP8

    Absolute Maximum Ratings at Ta = 25˚C


    Parameter Symbol Conditions Ratings Unit
    Maximum Supply Voltage VCC max 18 V
    Allowable Power Dissipation Pd max 200 mW
    Operating Temperature Topr –20 to +75 ˚C
    Storage Temperature Tstg –40 to +125 ˚C

    Recommended Operating Conditions at Ta = 25˚C


    Parameter Symbol Conditions Ratings Unit
    Supply Voltage VCC 9 V
    Load Resistance RL 10k Ω

    Operating Conditions at Ta = 25˚C, VCC=9V, RL=10kΩ, Rg=600Ω, f=1kHz, NAB


    Ratings
    Parameter Symbol Conditions Unit
    min typ max
    Current Dissipation ICC 6.5 8.0 mA
    Closed loop 35 dB
    Voltage Gain VG
    Open loop, VO=0.77V 70 78 dB
    Output Voltage VO THD=1% 1.0 1.3 V
    Total Harmonic Distortion THD VO=0.5V 0.05 0.30 %
    Input Resistance ri 70k 100k Ω
    Continued on next page.

    Any and all SANYO products described or contained herein do not have specifications that can handle
    applications that require extremely high levels of reliability, such as life-support systems, aircraft’s
    control systems, or other applications whose failure can be reasonably expected to result in serious
    physical and/or material damage. Consult with your SANYO representative nearest you before using
    any SANYO products described or contained herein in such applications.
    SANYO assumes no responsibility for equipment failures that result from using products at values that
    exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other
    parameters) listed in products specifications of any and all SANYO products described or contained
    herein.

    SANYO Electric Co.,Ltd. Semiconductor Company


    TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
    10700TH (KT)/N0493TH/7160TS/O137KI/8044KI/9250KI, TS No.573–1/7
    LA3161
    Continued from preceding page.
    Ratings
    Parameter Symbol Conditions Unit
    min typ max
    Equivalent Input Noise Voltage VNI Rg=2.2kΩ 1.2 2.0 µF
    Crosstalk CT Rg=2.2kΩ –50 –65 dB
    Ripple Rejection Rr –40 dB

    Equivalent Circuit Block Diagram

    Test Circuit1 : VO, VG, THD, ICC, ri Test Circuit2 : VGO

    Test Circuit3 : Noise

    No.573–2/7
    LA3161

    Sample Application Circuit 1 : Preamplifier for Car Stereo

    Function of External Parts


    C2, C4 are input coupling capacitors. In NAB equalizer amplifier, the gain at low frequencies is high and 1/f noise
    inside the IC is emphasized as output noise. Therefore, if the reactance of capacitor at low frequencies is increased,
    the dependence of 1/f noise on the signal source resistance causes the output noise voltage to deteriorate, and the
    value of reactance must be made small enough as compared with the signal source resistance. C2, C4 also influence
    the operation start time and the adequate value of these capacitors is 10µF. (Since C2, C4 of less than 4.7µF make the
    operation start time longer, use C2, C4, of 4.7µF or more).
    C5, C11 are NF capacitors. The lower cut-off frequency depends on the value of these capacitors.
    If the lower cut-off frequency is taken as fL :
    C5 (C11) = 1/2π · fL · R2 (R7)
    If the value of this capacitor is made larger, the operation start time of amplifier is more delayed. The adequate value
    of capacitor is 47µF.
    The frequency characteristic of the equalizer amplifier depends on C6 and R4, R3 (C10 and R5, R6).
    The time constants to obtain the standard NAB characteristic are as shown below.
    Tape speed 9.5cm/s 4.75cm/s
    C6 (R3 + R4) 3180µs 1590µs
    R3 C6 90µs 120µs

    C8 is bias capacitor for the power line. C8 of 47µF is inserted at a point as close to the power supply pin (pin 4) as
    possible.
    C1, C3 are for preventing radio interference in the strong electric field, interference attributable to engine noise, and
    blocking oscillation at the time of large amplitude operation. The adequate value of C1, C3 is approximately 1000pF.
    C7, C9 are output coupling capacitors. The adequate value of C7, C9 is 10µF.

    No.573–3/7
    LA3161

    NAB element and determination of gain


    Since the DC feedback is provided by R1, R2 of NAB element, which brings about DC output potential at pins 3, 6, it
    is impossible to change the value of R1, R2 of NAB element greatly. Therefore, when determining the gain, change
    RNF with R1, R2, C1 (NAB element) kept constant.

    (1) How to obtain RNF


    Impedance Z of NAB element is
    1
    Z= + R2
    1/R1+jωC1
    1+jωC1 {R1R2/ (R1+R2)}
    = (R1+R2) { }
    1+jωC1R1

    For a general negative feedback amplifier circuit, A=Ao/(1+Aoβ) applies, and Z=A · RNF is obtained under
    conditions of Ao>>A, A>>1 (β=RNF/ (RNF+Z), Ao=open-loop gain, A=feedback gain).
    Therefore, we can use an approximation of RNF=Z/A.
    A= (VG for 1kHz) times, (Set R1, R2 at approximately 100kΩ)
    Each time constant of NAB characteristic.
    Tape speed 9.5cm/s 4.75cm/s
    T1 C1, R1 3180µs 1590µs
    T2 C1 (R1//R2) 90µs 120µs

    (2) Examples of NAB Constants

    (a) Tape speed : 9.5cm/s. (8 tracks)

    VG : RNF (VG/f=1kHz)
    VG 30 35 40 dB
    RNF 180 100 56 Ω

    (b) Tape speed : 4.75cm/s. (cassette)

    VG : RNF
    VG 30 35 40 dB
    RNF 440 240 130 Ω

    (c) Flat amplifier


    VG : RNF
    VG 30 35 40 dB
    RNF 3.2 1.8 1 kΩ

    No.573–4/7
    LA3161

    Proper cares in using IC


    1. Maximum Rating
    If the IC is used in the vicinity of the maximum rating, even a slight variation in conditions may cause the maxi-
    mum rating to be exceeded, thereby leading to a breakdown. Allow an ample margin of variation for supply
    voltage, etc. and use the IC in the range where the maximum rating is not exceed.
    2. Short between pins
    If the supply voltage is applied when the space between pins is shorted, a breakdown or deterioration may occur.
    When installing the IC on the board or applying the supply voltage, make sure that the space between pins is not
    shorted with solder, etc.
    3. Breakdown of IC attributable to inverted insertion
    If the IC is inserted inversely and operated, the IC may suffer from something unusual, thereby leading to a
    breakdown or deterioration of the IC. When installing the IC on the board or operating the IC, check the marked
    surface of IC.

    Proper cares to be taken for obtaining optimum operation of IC


    · Set DC resistance of R1, R2 of NAB element at approximately 100kΩ.
    · Determine the gain by changing RNF without chaging NAB constant (Refer to Examples of NAB constant.).

    No.573–5/7
    LA3161

    No.573–6/7
    LA3161

    Specifications of any and all SANYO products described or contained herein stipulate the performance,
    characteristics, and functions of the described products in the independent state, and are not guarantees
    of the performance, characteristics, and functions of the described products as mounted in the customer's
    products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
    the customer should always evaluate and test devices mounted in the customer's products or equipment.
    SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
    semiconductor products fail with some probability. It is possible that these probabilistic failures could
    give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
    or that could cause damage to other property. When designing equipment, adopt safety measures so
    that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
    circuits and error prevention circuits for safe design, redundant design, and structural design.
    In the event that any or all SANYO products(including technical data,services) described or
    contained herein are controlled under any of applicable local export control laws and regulations,
    such products must not be expor ted without obtaining the expor t license from the authorities
    concerned in accordance with the above law.
    No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
    mechanical, including photocopying and recording, or any information storage or retrieval system,
    or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
    Any and all information described or contained herein are subject to change without notice due to
    product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
    for the SANYO product that you intend to use.
    Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not
    guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
    no guarantees are made or implied regarding its use or any infringements of intellectual property rights
    or other rights of third parties.

    This catalog provides information as of January, 2000. Specifications and information herein are subject
    to change without notice.

    PS No.573–7/7

    You might also like