Electronics Projjects1

CIRCUIT IDEAS
MULTI-SWITCH DOORBELL WITH INDICATORS

T.K. HAREENDRAN
I VED DWI S.C.
eres the circuit of a multi-switch input musical doorbell (shown in Fig.1). The circuit is built around the popular and less expensive quad D-latch CD4042B (IC1). When switch S6 is pushed to on condition, the circuit gets +9V and the four data inputs (D1 through D4) of ICI are in low state because these are tied to ground via resistors R1 through R4. Polarity input (POL) pin 6 of IC1 is
also pulled down by resistor R5. Clock input (pin 5) of the quad D-latch is wired in normally low mode and hence all the four outputs (Q0 through Q3) have the same states as their corresponding data inputs. As a result, LED1 through LED4 are in off condition. There are four switches fitted at four different doors/gates outside the home and a monitoring panel (as shown in Fig. 2) in the common room of the home. If any switch is pressed by a visitor (for example,
Fig. 2: Suggested panel layout of musical doorbell
Fig. 1: Multi-switch doorbell with indicators
switch S1 at door 1), pins 2 and 4 of IC1 go high. Simultaneously, pin 3 to IC1 (Q0 output) goes low and LED1 starts glowing to indicate that switch S1 is pressed by someone. Next, output pin 13 of the dual 4-input NOR gate (IC2, here wired as a single 4-input OR gate) goes high to forward bias buzzerdriver transistor T1 via resistor R10. The final result is a soft and pleasing musical bell, which lasts until reset switch S5 is pressed by the owner. For this latching arrangement , output pin 13 of IC2 from the NOR gate is fed back to the clock input of IC1. The circuit costs around Rs 100.
ELECTRONICS FOR YOU
APRIL 2003
CIRCUIT IDEAS
SONG NUMBER DISPLAY

PRABHASH K.P.
SAN
O I THE
eres a circuit to display the song number in an audio system for quick reference to songs. It also serves the purpose of an extra visual indicator in modern audio systems. When the power is switched on, the power-on-reset circuit comprising 3.3k resistor R20 and 1F, 25V capacitor C6 resets the counters, showing 00 in the display. One can also reset the display to zero at any time by pressing reset switch S1. When the first song starts playing, the output pins of IC1 (KA2281) go low and capacitor C5 starts charging. This forward biases transistor T1 and hence the input to IC3 at pin 1 goes to high state. As a result, the output of the counter goes to the next state, showing 01 on the display. The counter remains in this state until the song is completed. During the time gap before the next song starts playing, capacitor C5 discharges. After discharging of capacitor C5, the input to IC3 becomes low again. When the song starts, the process described above is repeated and the display shows 02. You can adjust VR3 to change the time gap setting. This must be set such that the circuit doesnt respond to short gaps, if any, within a song and responds only to long gaps between different songs. Transistor T2 helps in gap-delay adjustment. The intensity of LED11 diminishes when a song is completed and the counter is ready to accept the next pulse. Connect the input to the preamp output or equaliser output of the audio system. Adjust VR1 and VR2 to get the correct audio-level indication. If you are already using KA2281 for audio-level indication, just connect diodes D1 and D2 as shown in this circuit. Note that the counter counts the songs by detecting the gaps. Therefore any long gap within a song may cause false triggering and the display will also be incremented. However, as this is very unlikely to happen, the circuit shows the correct song number almost all the time. The circuit costs around Rs 100.
APRIL 2003
ELECTRONICS FOR YOU
CIRCUIT IDEAS
FLASHING BEACON
ASHOK K. DOCTOR
I VED DWI S.C.
flashing beacon has many uses. It can be employed as a distress signal on highways or as a direction pointer for parking lots, hospitals, hotels, etc. Here we present a flashing beacon that uses well-known regulator IC LM317T. As LM317T regulator can deliver more than 1 amp. A small 12V, 10W bulb with a high-quality reflector can serve as a good visible blinker. A 12-15V, 1A DC supply is connected to the input pin of the IC. A 12V, 10W bulb and a combination of resistors and capacitors are connected between the output pin and ADJ pin of the IC as shown in
the figure. The IC is provided with an aluminium heat-sink to dissipate the heat generated while delivering full current. Since the IC has an inbuilt switch-on current limiter, it extends the bulb life. For the shown values of resistors and capacitors, the bulb flashes at approximately 4 cycles per second. The number of flashes depends on the charge-discharge time of the capacitors. Different values of resistors and capacitors can be used to increase or de-
crease the number of flashes. This circuit costs around Rs 50.
NOVEMBER 2002
ELECTRONICS FOR YOU
CIRCUIT IDEAS
INTRUDER RADIO ALERT SYSTEM

DAVID NASH PIOUS
SUN
IL KU
MAR
onsider a situation where a burglar has entered your house and snapped the telephone wires, leaving you with no means of communication with the outside world. In such an emergency, you will find this intruder alarm to be very handy. It transmits a prerecorded emergency message repeatedly for reception by an FM receiver. The message containing address, geographical location, name, etc is recorded onto a chip. The prerecorded message can then be transmitted repeatedly with the help of an FM transmitter, in the hope that some noble soul will hear it and inform the police about the incident. The circuit comprises a sound recording-and-playback chip (UM5506BH). This chip consists of a 96kbit SRAM and can record up to six seconds of audio. (For details, refer Mini Voice Processor circuit published in April 2000 issue of EFY.) After the required message has been recorded, it is passed to a low-power, VHF FM transmitter wired around BC547 and 2N2369 transistors. The range of this trans-
Fig. 2: Circuit diagram of intruder radio alert system
Fig. 1: Block diagram of the intruder radio alert system
mitter is 60 to 100 metres using a 40-70cm long wire as an antenna. The major advantage of this circuit is its low power consumption. The author operated it on 3V button cells (Maxell CR 2032, CR 2025, etc used in digital diaries). To transmit the prerecorded message, the play button is pressed repeatedly.
The transmitted message can be heard over the FM receiver. A possible modification, though it has legal complications, is to vary the coil inductance such that the transmission is on police band, thus alerting the police for quick help. Even the need of repeatedly pressing play button can be obviated by configuring an astable multiviberator (using IC 555 timer) to trigger IC UM5506BH every six seconds so that the message is played repeatedly. This circuit costs around Rs 200.
DECEMBER 2002
ELECTRONICS FOR YOU
CIRCUIT IDEAS
AUTOMATED TRAFFIC SIGNAL CONTROLLER

VIKRAM BANERJEE MRINAL KANTI MANDAL DR ANIRUDHA GHOSAL
RUP
ANJA
NA
his automated traffic signal controller can be made by suitably programming a GAL device. (For GAL programming you may refer to the con-
sity is high. This controller allows the pedestrians to safely cross the road during certain periods. 3. The controller uses digital logic, which can be easily implemented by using logic gates. 4. The controller is a generalised one and can be used for different roads with
of 8 seconds each. For the left- and rightturning traffic and pedestrians crossing from north to south, south to north, east to west, and west to east, only green and red signals are used. Table I shows the simultaneous states of the signals for all the traffic. Each row represents the status of a signal for 8
Fig. 1: Flow of traffic in all possible directions
TABLE I Simultaneous States of Signals for All the Traffic

X 0 0 0 0 1 1 1 1 Y 0 0 1 1 0 0 1 1 Z 0 1 0 1 0 1 0 1 B-C/B-G Lt/Rt R R R G R R R R B-E St R G G Y R R R R D-E/D-A Lt/Rt R R R R R R R G D-G St R R R R R G G Y F-G/F-C Lt/Rt G R R R R R R R F-A St G G Y R R R R R H-A/H-E Lt/Rt R R R R G R R R HC St R R R R G G Y R WALK (N-S)/(S-N) R G G R R R R R WALK (E-W)/(W-E) R R R R R G G R
struction project published on page 52 in EFYs September issue.) Its main features are: 1. The controller assumes equal traffic density on all the roads. 2. In most automated traffic signals the free left-turn condition is provided throughout the entire signal period, which poses difficulties to the pedestrians in crossing the road, especially when the traffic den-
slight modification. 5. The control can also be exercised manually when desired. The time period for which green, yellow, and red traffic signals remain on (and then repeat) for the straight moving traffic is divided into eight units of 8 seconds (or multiples thereof) each. Fig. 1 shows the flow of traffic in all permissible directions during the eight time units
seconds. As can be observed from the table, the ratio of green, yellow, and red signals is 16:8:40 (=2:1:5) for the straight moving traffic. For the turning traffic the ratio of green and red signals is 8:56 (=1:7), while for pedestrians crossing the road the ratio of green and red signals is 16:48 (=2:6). In Table II (as well as Table I) X, Y, and Z are used as binary variables to
NOVEMBER 2002 ELECTRONICS FOR YOU
CIRCUIT IDEAS
TABLE II Boolean Functions for All the Signal Conditions
Signal Reference Boolean functions Green B-C(Lt)/B-G (Rt) XYZ Green B-E (St) XYZ+XYZ Red B-E (St) X+YYZ Yellow B-E (St) XYZ Green D-E (Lt)/D-A (Rt) XYZ Green D-G (St) XYZ+XYZ Red D-G (St) X+XYZ Yellow D-G (St) XYZ Green F-G(Lt)/F-C (Rt) XYZ Green F-A (St) XY Red F-A (St) X+XYZ Yellow F-A (St) XYZ Green H-A (Lt)/H-E (Rt) XYZ Green H-C (St) XY Red H-C (St) X+XYZ Yellow H-C (St) XYZ Green Walk (N-S/S-N) XYZ+XYZ Green Walk (E-W/W-E) XYZ+XYZ Note. X, Y, and Z denote complements of variables X, Y, and Z, respectively.
depict the eight states of 8 seconds each. Letters A through H indicate the left and right halves of the roads in four directions as shown in Fig. 1. Two letters with a dash in between indicate the direction of permissible movement from a road. Straight direction is indicated by St, while left and right turns are indicated by Lt and Rt, respectively. The Boolean functions for all the signal conditions are shown in Table II. The left- and the right-turn signals for the traffic have the same state, i.e. both are red or green for the same duration, so their Boolean functions are identical and they should be connected to the same con-
Fig. 2: The circuit diagram for traffic light signalling

ELECTRONICS FOR YOU NOVEMBER 2002
trol output. The circuit diagram for realising these Boolean functions is shown in Fig. 2. Timer 555 (IC1) is wired as an astable multivibrator to generate clock signal for the 4-bit counter 74160 (IC2). The time duration of IC1 can be adjusted by varying the value of resistor R1, resistor R2, or capacitor C2 of the clock circuit. The on time duration T is given by the following relationship: T = 0.695C2(R1+R2) IC2 is wired as a 3-bit binary counter by connecting its Q3 output to reset pin 1 via inverter N1. Binary outputs Q2, Q1, and Q0 form variables X, Y, and Z, respectively. These outputs, along with their complimentary outputs X, Y, and Z, respectively, are used as inputs to the rest of the logic circuit to realise various outputs satisfying Table I. You can simulate various traffic lights using green, yellow, and red LEDs and feed the outputs of the circuit to respective LEDs via current-limiting resistors of 470 ohms each to check the working of the circuit. Here, for turning traffic and pedestrians crossing the road, only green signal is made available. It means that for the remaining period these signals have to be treated as red. In practice, the outputs of Fig. 2 should be connected to solidstate relays to operate high-power bulbs. Further, if a particular signal condition (such as turning signal) is not applicable to a given road, the output of that signal condition should be
CIRCUIT IDEAS
connected to green signal of SIG-B SIG-D SIF-F SIG-H WALK(N-S) WALK(E-W) the next GGRY GGRY GGRY GGRY GR GR state (refer 0010 0100 1100 0010 01 01 Table I). 0100 0100 0100 0010 10 01 T h e 0100 0100 0001 0010 10 01 traffic sig1001 0100 0010 0010 01 01 nals can 0010 0100 0010 1100 01 01 also be 0010 1000 0010 0100 01 10 controlled 0010 1000 0010 0001 01 10 manually, 0010 0011 0010 0010 01 01 if desired. Note. The first column under G (green) in each group of four signals indicates the Any signal turn signal, while the next three columns under GRY indicate signal for the straight state can be traffic. established Table III Execution Results of Software Program by entering the binary value corresponding to that particular state into the parallel input pins of the 3-bit counter. Similarly, the signal can be reset at any time by providing logic 0 at the reset pin (pin 1) of the counter using an external switch. A software program to verify the functioning of the circuit using a PC is given below. (Source code and executable file will be provided in the next months EFY-CD.) When executing the program, keep pressing Enter key to get the next row of results. The test results on execution of the program is shown in Table III. This circuit costs around Rs 125.
TRAFFIC.C
#include<stdio.h> #include<conio.h> #define TRUE 1 #define False 0 int not(int x); int or2(int x,int y); int or3(int x,int y,int z); int and2(int x,int y); int and3(int x,int y,int z); int main(void) { int a,b,c; int seq,green_bl,green_bs,red_bs,yellow_bs; int green_dl,green_ds,red_ds,yellow_ds; int green_fl,green_fs,red_fs,yellow_fs; int green_hl,green_hs,red_hs,yellow_hs; int walk_ns,stop_ns; int walk_ew,stop_ew; clrscr(); printf( SIG-B SIG-D SIF-F SIG-H WALK(N-S) WALK(E-W)\n); printf(G G R Y G G R Y G G R Y G G R Y GR G R\n); for(seq=0;seq<8;seq++) { c=(seq&1);b=(seq&2)>>1;a=(seq&4)>>2; green_bl=and3(not(a),b,c); green_bs=or2(and3(not(a),b,not(c)),and3(not(a),not(b),c)); red_bs=or2(a,and3(not(a),not(b),not(c))); yellow_bs=and3(not(a),b,c); green_dl=and3(a,b,c); green_ds=or2(and3(a,b,not(c)),and3(a,not(b),c)); red_ds=or2(not(a),and3(a,not(b),not(c))); yellow_ds=and3(a,b,c); green_fl=and3(not(a),not(b),not(c)); green_fs=and2(not(a),not(b)); red_fs=or2(a,and3(not(a),b,c)); yellow_fs=and3(not(a),b,not(c)); green_hl=and3(a,not(b),not(c)); green_hs=and2(a,not(b)); red_hs=or2(not(a),and3(a,b,c)); yellow_hs=and3(a,b,not(c)); walk_ns=green_bs; stop_ns=or3(and3(not(a),not(b),not(c)),and3(not(a),b,c),a); walk_ew=green_ds; stop_ew=or3(not(a),and3(a,b,c),and3(a,not(b),not(c))); printf(%d %d %d %d %d %d %d %d %d %d %d %d %d %d %d %d %d %d %d %d\n, green_bl,green_bs,red_bs,yellow_bs, green_dl,green_ds,red_ds,yellow_ds, green_fl,green_fs,red_fs,yellow_fs, green_hl,green_hs,red_hs,yellow_hs, walk_ns,stop_ns, walk_ew,stop_ew); getch(); } return; } int and2(int x,int y) { return(x && y); } int and3(int x,int y,int z) { return(x && y && z); } int or2(int x,int y) { return(x || y); } int or3(int x,int y,int z) { return(x || y || z); } int not(int x) { return(!x); }
NOVEMBER 2002
ELECTRONICS FOR YOU
CIRCUIT IDEAS
INFRARED TOY CAR MOTOR CONTROLLER

T.K. HAREENDRAN
SAN
I THE
his add-on circuit enables remote switching on/off of battery-operated toy cars with the help of a TV/ video remote control handset operating at 3040 kHz. When the circuit is energised from a 6V battery, the decade counter CD4017 (IC2), which is configured as a toggle flip-flop, is immediately reset by the power-onreset combination of capacitor C3 and resistor R6. LED1 connected to pin 3 (Q0) of IC2 via resistor R5 glows to indicate the standby condition. In standby condition, data output pin of the integrated infrared receiver/demodulator (SFH505A or TSOP1738) is at a high level (about 5 volts) and transistor T1 is off (reverse biased). The monostable wired around IC1 is inactive in this condition. When any key on the remote control handset is depressed, the output of the IR receiver momentarily transits through low state and transistor T1 conducts. As a result, the monostable is triggered and a short pulse is applied to the clock input (pin 14) of IC2, which takes Q1 output (pin 2) of IC2 high to switch on motor driver transistor T2 via base bias resistor R7 and the motor starts rotating continously (car starts running). Resistor R8 limits the starting current. When any key on the handset is
depressed again, the monostable is retriggered to reset decade counter IC2 and the motor is switched off. Standby LED1 glows again.
example, behind the front glass, and connect its wires to the circuit board using a short 3-core ribbon cable/shielded wire. Note. Since the circuit uses modu-
This circuit can be easily fabricated on a general-purpose printed board. After construction, enclose it inside the toy car and connect the supply wires to the battery of the toy car with right polarity. Rewire the DC motor connections and fix the IR receiver module in a suitable location, for
lated infrared beam for control function, ambient light reflections will not affect the circuit operation. However, fluorescent tubelights with electronic ballasts and CFL lamps may cause malfunctioning of the circuit.
JULY 2002
ELECTRONICS FOR YOU
CIRCUIT
IDEAS
ANTI-THEFT SECURITY FOR CAR AUDIOS

T.K. HAREENDRAN
EDI DWIV S.C.
his small circuit, based on popular CMOS NAND chip CD4093, can be effectively used for protecting your expensive car audio system against theft. When 12V DC from the car battery is
Whenever an attempt is made to remove the car audio from its mounting by cutting its connecting wires, the optocoupler immediately turns off, as its LED cathode terminal is hanging. As a result, the oscillator circuit built around
applied to the gadget (as indicated by LED1) through switch S1, the circuit goes into standby mode. LED inside optocoupler IC1 is lit as its cathode terminal is grounded via the car audio (amplifier) body. As a result, the output at pin 3 of gate N1 goes low and disables the rest of the circuit.
gates N2 and N3 is enabled and it controls the on/off timings of the relay via transistor T2. (Relay contacts can be used to energise an emergency beeper, indicator, car horns, etc, as desired.) Different values of capacitor C2 give different on/off timings for relay RL1 to be on/off. With 100F we get approxi-
mately 5 seconds as on and 5 seconds as off time. Gate N4, with its associated components, forms a self-testing circuit. Normally, both of its inputs are in high state. However, when one switches off the ignition key, the supply to the car audio is also disconnected. Thus the output of gate N4 jumps to a high state and it provides a differentiated short pulse to forward bias transistor T1 for a short duration. (The combination of capacitor C1 and resistor R5 acts as the differentiating circuit.) As a result, buzzer in the collector terminal of T1 beeps for a short duration to announce that the security circuit is intact. This on period of buzzer can be varied by changing the values of capacitor C1 and/or resistor R5. After construction, fix the LED and buzzer in dashboard as per your requirement and hide switch S1 in a suitable location. Then connect lead A to the body of car stereo (not to the body of vehicle) and lead B to its positive lead terminal. Take power supply for the circuit from the car battery directly. Caution. This design is meant for car audios with negative ground only.
ELECTRONICS FOR YOU JULY 2001
CIRCUIT
IDEAS
SIMPLE TELEPHONE RING TONE GENERATOR

K. UDHAYA KUMARAN, VU3GTH
MAR IL KU SUN
ere is a simple telephone ring tone generator circuit designed using only a few components. It produces simulated telephone ring tone and needs only DC voltage (4.5V DC to 12V DC). One may use this circuit in ordinary intercom or phone-type intercom.
tor (CMOS IC CD4060B) is used to generate three types of pulses, which are available from pin 1 (O11), pin 3 (O13), and pin 14 (O7), respectively. Preset VR1 is adjusted to obtain 0.3125Hz pulses (1.6second low followed by 1.6-second high) at pin 3 of IC1. At the same time, pulses available from pin 1 will be of 1.25 Hz
The sound is quite loud when this circuit is operated on +12V DC power supply. However, the volume of ring sound is adjustable. The commonly available 14-stage binary ripple counter with built-in oscilla-
(0.4-second low, 0.4-second high) and 20 Hz at pin 14. The three output pins of IC1 are connected to base terminals of transistors T1, T2, and T3 through resistors R1, R2, and R3, respectively. Transistors T1 through T3 are cas-
caded in such a way that the positive voltage available at the emitter of transistor T1 is extended to the collector of transistor T3 when the outputs of all the three stages are low. As a result, transistors T1 through T3 are forward biased for 0.4, 1.6, and 0.025 seconds, respectively and reverse biased for similar durations. Using a built-in oscillator-type piezobuzzer produces around 1kHz tone. In this circuit, the piezo-buzzer is turned on and off at 20 Hz for ring tone sound by transistor T3. 20Hz pulses are available at the collector of transistor T3 for 0.4-second duration. After a time interval of 0.4 second, 20Hz pulses become again available for another 0.4-second duration. This is followed by two seconds of nosound interval. Thereafter the pulse pattern repeats itself. Refer the figure that indicates waveforms available at various points including the collector of transistor T3. Preset VR2 can be used for adjusting the amplitude of the ring tone.
CIRCUIT
IDEAS
DTMF PROXIMITY DETECTOR

K.S. SANKAR
RUP ANJA NA
DTMF-based IR transmitter and receiver pair can be used to realise a proximity detector. The circuit presented here enables you to detect any object capable of reflecting the IR beam and moving in front of the IR LED photodetector pair up to a distance of about 12 cm from it.
column 1 (pin 12) get connected together via transistor T2 after a power-on delay (determined by capacitor C1 and resistors R1 and R16 in the base circuit of the transistor) to generate DTMF tone (combination of 697 Hz and 1209 Hz) corresponding to keypad digit 1 continuously. LED 2 is used to indicate the tone
from an object, falls on photodetector diode D1. (The photodetector is to be shielded from direct IR light transmission path of IR LED1 by using any opaque partition so that it receives only the reflected IR light.) On detection of the signal by photodetector, it is coupled to DTMF decoder IC2 through emitter-follower transistor T1. When the valid tone pair is detected by the decoder, its StD pin 15 (shorted to TOE pin 10) goes high. The detection of
The circuit uses the commonly available telephony ICs such as dial-tone generator 91214B/91215B (IC1) and DTMF decoder CM8870 (IC2) in conjunction with infrared LED (IR LED1), photodiode D1, and other components as shown in the figure. A properly regulated 5V DC power supply is required for operation of the circuit. The transmitter part is configured around dialer IC1. Its row 1 (pin 15) and
output from IC3. This tone output is amplified by Darlington transistor pair of T3 and T4 to drive IR LED1 via variable resistor VR1 in series with fixed 10-ohm resistor R14. Thus IR LED1 produces tone-modulated IR light. Variable resistor VR1 controls the emission level to vary the transmission range. LED 3 indicates that transmission is taking place. A part of modulated IR light signal transmitted by IR LED1, after reflection
the object in proximity of IR transmitterreceiver combination is indicated by LED1. The active-high logic output pulse (terminated at connector CON1, in the figure) can be used to switch on/off any device (such as a siren via a latch and relay driver) or it can be used to clock a counter, etc. This DTMF proximity detector finds applications in burglar alarms, object counter and tachometers, etc.
ELECTRONICS FOR YOU JUNE 2001
CIRCUIT
IDEAS
UNDER-/OVER-VOLTAGE BEEP FOR MANUAL STABILISER

K. UDHAYA KUMARAN
MAR IL KU SUN
anual stabilisers are still popular because of their simple construction, low cost, and high reliability due to the absence of any relays while covering a wide range of mains AC voltages compared to that handled by automatic voltage stabilisers. These are used mostly in homes and in business centres for loads such as lighting, TV, and fridge, and in certain areas where the mains AC voltage fluctuates between very low (during peak hours) and abnormally high (during non-peak hours). Some manual stabilisers available in the market incorporate the high-voltage
eration is very irritating and inconvenient for the user. This under-/over-voltage audio alarm circuit designed as an add-on circuit for the existing manual stabilisers overcomes the above problem. Whenever the stabilisers output voltage falls below a preset low-level voltage or rises above a preset high-level voltage, it produces different beep sounds for high and low voltage levelsshort-duration beeps with short intervals between successive beeps for high voltage level and slightly longerduration beeps with longer interval between successive beeps for low voltage
auto-cut-off facility to turn off the load when the output voltage of manual stabiliser exceeds a certain preset high voltage limit. The output voltage may become high due to the rise in AC mains voltage or due to improper selection by the rotary switch on manual stabiliser. One of the major disadvantage of using a manual stabiliser in areas with a wide range of voltage fluctuations is that one has to keep a watch on the manual stabilisers output voltage that is displayed on a voltmeter and keep changing the same using its rotary switch. Or else, the output voltage may reach the preset autocut-off limit to switch off the load without the users knowledge. To turn on the load again, one has to readjust the stabiliser voltage using its rotary switch. Such op-
level. By using these two different types of beep sounds one can readily readjust the stabilisers AC voltage output with the help of the rotary switch. There is no need of frequently checking voltmeter reading. It is advisable to preset the high-level voltage 10V to 20V less than the required high-voltage limit for auto-cut-off operation. Similarly, for low level one may preset low-level AC voltage 20V to 30V above minimum operating voltage for a given load. The primary winding terminals of step-down transformer X1 are connected to the output terminals of the manual stabiliser. Thus, 9V DC available across capacitor C1 will vary in accordance with the voltage available at the output terminals of the manual stabiliser, which is
ELECTRONICS FOR YOU MAY 2001
used to sense high or low voltage in this circuit. Transistor T1 in conjunction with zener diode ZD1 and preset VR1 is used to sense and adjust the high-voltage level for beep indication. Similarly, transistor T2 along with zener ZD2 and preset VR2 is used to sense and adjust low voltage level for beep indication. When the DC voltage across capacitor C1 rises above the preset high-level voltage or falls below the preset low-level voltage, the collector of transistor T2 becomes high due to non-conduction of transistor T2, in either case. However, if the DC voltage sampled across C1 is within the preset high- and low-level voltage, transistor T2 conducts and its collector voltage gets pulled to the ground level. These changes in the collector voltage of transistor T2 are used to start or stop oscillations in the astable multivibrator circuit that is built around transistors T3 and T4. The collector of transistor T4 is connected to the base of buzzer driver transistor T5 through resistor R8. Thus when the collector voltage of transistor T4 goes high, the buzzer sounds. Preset VR3 is used to control the volume of buzzer sound. In normal condition, the DC voltage sampled across capacitor C1 is within the permissible window voltage zone. The base of transistor T3 is pulled low due to conduction of diode D2 and transistor T2. As a result, capacitor C2 is discharged. The astable multivibrator stops oscillating and transistor T4 starts conducting because transistor T3 is in cut-off state. No beep sound is heard in the buzzer due to conduction of transistor T4 and non-conduction of transistor T5. When the DC voltage across capacitor C1 goes above or below the window voltage level, transistor T2 is cut off. Its collector voltage goes high and diode D2 stops conducting. Thus there is no discharge path for capacitor C2 through diode D2. The astable multivibrator starts
CIRCUIT
IDEAS
oscillating. The time period for which the beep is heard and the time interval between two successive beeps are achieved with the help of the DC supply voltage, which is low during low-level voltage sampling and high during high-level voltage
sampling. The time taken for charging capacitors C2 and C3 is less when the DC voltage is high and slightly greater when the DC voltage is low for astable multivibrator operation. Thus during lowlevel voltage sensing the buzzer beeps for
longer duration with longer interval between successive beeps compared to that during high-voltage level sensing. This circuit can be added to any existing stabiliser (automatic or manual) or UPS to monitor its performance.
CIRCUIT
IDEAS
15-STEP DIGITAL POWER SUPPLY

NAVEEN THARIYAN
RUP ANJA NA
ere is a simple circuit to obtain variable DC voltage from 1.25V to 15.19V in reasonably small steps as shown in the table. The input voltage may lie anywhere between 20V
down by closing switch S2. The output of counter IC2 is used to realise a digitally variable resistor. This section consists of four N/O reed relays that need just about 5mA current for their
ing resistor across the relay contacts gets connected to the circuit. The table shows the theoretical output for various digital input combinations. The measured output is nearly equal to the theoretically calculated output across regulator IC3 (LM317). The output voltage is governed by the following relationship as long as the input-to-output differential is greater than or equal to 2.5V: Vout = 1.25(1+R2'/R1') Where, R1' = R15 = 270 ohms (fixed)
and 35V. The first section of the circuit comprises a digital up-down counter built around IC1 a quad 2-input NAND schmitt trigger (4093), followed by IC2 a binary up-down counter (4029). Two gates of IC 4093 are used to generate up-down logic using push buttons S1 and S2, respectively, while the other two gates form an oscillator to provide clock pulses to IC2 (4029). The frequency of oscillations can be varied by changing the value of capacitor C1 or preset VR1. IC2 receives clock pulses from the oscillator and produces a sequential binary output. As long as its pin 5 is low, the counter continues to count at the rising edge of each clock pulse, but stops counting as soon as its pin 5 is brought to logic 1. Logic 1 at pin 10 makes the counter to count upwards, while logic 0 makes it count downwards. Therefore the counter counts up by closing switch S1 and counts
operation. (EFY lab note. The original circuit containing quad bilateral switch IC 4066 has been replaced by reed relays operated by transistorised switches because of unreliable operation of the former.) The switching action is performed using BC548 transistors. External resistors are connected in parallel with the reed relay contacts. If particular relay contacts are opened by the control input at the base of a transistor, the correspondELECTRONICS FOR YOU MAY 2001
and R2' = R11 + R12 + R13 + R14 = 220 + 470 + 820 +1500 ohms = 3,010 ohms (with all relays energised) One can use either the binary weighted LED display as indicated by LED1 through LED4 in the circuit or a 74LS154 IC in conjunction with LED5 through LED20 to indicate one of the 16 selected voltage steps of Table I. The input for IC4 is to be tapped from points
CIRCUIT
IDEAS
TABLE
Binary output 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Equivalent dec no. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 LED4 R14 (W) Shorted Shorted Shorted Shorted Shorted Shorted Shorted Shorted 1500 1500 1500 1500 1500 1500 1500 1500 LED3 R13 (W) Shorted Shorted Shorted Shorted 820 820 820 820 Shorted Shorted Shorted Shorted 820 820 820 820 LED2 R12 (W) Shorted Shorted 470 470 Shorted Shorted 470 470 Shorted Shorted 470 470 Shorted Shorted 470 470 LED1 R11 (W) Shorted 220 Shorted 220 Shorted 220 Shorted 220 Shorted 220 Shorted 220 Shorted 220 Shorted 220 R2' (W) 0 220 470 690 820 1040 1290 1510 1500 1720 1970 2190 2390 2540 2790 3010 Vout (V) 1.25 2.27 3.43 4.44 5.05 6.06 7.22 8.24 8.19 9.21 10.37 11.39 11.99 13.01 14.17 15.19
marked A through D in the figure. This arrangement can be used to replace the LED arrangement at points A, B, C, and D. This 74LS154 IC is a decoder/ demultiplexer that senses the output of IC2 and accordingly activates only one of its 16 outputs in accordance with the
count value. LEDs at the output of this IC can be arranged in a circular way along side the corresponding voltages.
Working
When the power is switched on, IC2 re-
sets itself, and hence the output at pins 6, 11, 14, and 12 is equivalent to binary zero, i.e. 0000. The corresponding DC output of the circuit is minimum (1.25V). As count-up switch S1 is pressed, the binary count of IC2 increases and the output starts increasing too. At the highest count output of 1111, the output voltage is 15.19V (assuming the in-circuit resistance of preset VR2 as zero). Preset VR2 can be used for trimming the output voltage as desired. To decrease the output voltage within the range of 1.25V to 15.2V, count-down switch S2 is to be depressed. Notes. 1. When relay contacts across a particular resistor are opened, the corresponding LED glows. 2. The output voltages are shown assuming the in-circuit resistance of preset VR2 as zero. Thus when the in-circuit resistance of preset VR2 is not zero, the output voltage will be higher than that indicated here.
CIRCUIT
IDEAS
GENERATION OF 1-SEC. PULSES SPACED 5-SEC. APART

RUP
ANJA
NA
PRAVEEN SHANKER
his circuit using a dual-timer NE556 can produce 1Hz pulses spaced 5 seconds apart, either manually or automatically. IC NE556 comprises two independent NE555 timers in a single package. It is used to produce two separate pulses of different pulse widths, where one pulse initiates the activation of the second pulse. The first half of the NE556 is wired for 5-second pulse output. When slide switch S2 is in position a, the first timer is set for manual operation, i.e. by press-
ing switch S1 momentarily you can generate a single pulse of 5second duration. When switch S2 is kept in b position, i.e. pins 6 and 2 are shorted, timer 1 in NE556 triggers by itself. The output of the first timer is connected to trigger pin 8 of second timer, which, in turn, is connected to a potential divider comprising resistors R4 and R5. Resistor R1, preset VR1, resistor R2, preset VR2, and capacitors C2 and C5 are the components determining time period. Presets VR1 and VR2 permit trim-
ming of the 5-second and 1-second pulse width of respective sections. When switch S2 is in position a and switch S1 is pressed momentarily, the output at pin 5 goes high for about 5 seconds. The trailing (falling) edge of this 5second pulse is used to trigger the second timer via 0.1F capacitor C6. This action results in momentarily pulling down of pin 8 towards the ground potential, i.e. low. (Otherwise pin 8 is at 1/2 Vcc and triggers at/below 1/3 Vcc level.) When the second timer is triggered at the trailing edge of 5-second pulse, it generates a 1second wide pulse. When switch S2 is on position b, switch S1 is disconnected, while pin 6 is connected to pin 2. When capacitor C is charged, it is discharged through pin 2 until it reaches 1/3Vcc potential, at which it is retriggered since trigger pin 6 is also connected here. Thus timer 1 is retriggered after every 5-second period (corresponding to 0.2Hz frequency). The second timer is triggered as before to produce a 1-second pulse in synchronism with the trailing edge of 5-second pulse. This circuit is important wherever a pulse is needed at regular intervals; for instance, in Versatile Digital Frequency Counter Cum Clock construction project published in EFY Oct. 97, one may use this circuit in place of CD4060-based circuit. For the digital clock function, however, pin 8 and 12 are to be shorted after removal of 0.1F capacitor and 10-kilo-ohm resistors R4 and R5.
ELECTRONICS FOR YOU FEBRUARY 2001
CIRCUIT
IDEAS
AUTOMATIC HEAT DETECTOR

SUKANT KUMAR BEHARA
his circuit uses a complementary pair comprising npn metallic transistor T1 (BC109) and pnp germanium transistor T2 (AC188) to detect heat (due to outbreak of fire, etc) in the vicinity and energise a siren. The collector of transistor T1 is connected to the base of transistor T2, while the collector of transistor T2 is connected to relay RL1. The second part of the circuit comprises popular IC UM3561 (a siren and machine-gun sound generator IC), which can produce the sound of a fire-brigade siren. Pin numbers 5 and 6 of the IC are connected to the +3V supply when the relay is in energised state, whereas pin 2 is grounded. A resistor (R2) connected across pins 7 and 8 is used to fix the frequency of the inbuilt oscillator. The output is available from pin 3. Two transistors BC147 (T3) and BEL187 (T4) are connected in Darlington configuration to amplify the
lay is in energised state. LED1, connected in series with 68-ohm resistor EDI R1 across resistor R4, glows when the V I W D S.C. siren is on. To test the working of the circuit, bring a burning matchstick Pin Designation Sound Effect close to transistor T1 (BC109), SEL1 SEL2 which causes the resistance of its No Connection No Connection Police Siren emitter-collector junction to go low +3V No Connection Fire Engine Siren Ground No Connection Ambulance Siren due to a rise in temperature and it Do not care +3V Machine Gun starts conducting. Simultaneously, transistor T2 also conducts because its base is connected to the collector of transistor T1. As a result, relay RL1 energises and switches on the siren circuit to produce loud sound of a firebrigade siren. Lab note . We have added a sound from UM3561. Resistor R4 in setable to enable readers to obtain all posries with a 3V zener is used to provide sible sound effects by returning pins 1 the 3V supply to UM3561 when the re- and 2 as suggested in the table.
ELECTRONICS FOR YOU MARCH 2001
CIRCUIT
IDEAS
MUSICAL TOUCH BELL

SUKANT KUMAR BEHARA
EDI DWIV S.C.
ere is a musical call bell that can be operated by just bridging the gap between the touchplates with ones fingertips. Thus there is no need for a mechanical on/off switch because the touch-plates act as a switch. Other features include low cost and low power consumption. The bell can work on 1.5V or 3V, using one or two pencil cells, and can be used in homes and offices. Two transistors are used for sensing the finger touch and switching on a melody IC. Transistor BC148 is npn type while transistor BC558 is pnp type. The emitter of transistor BC148 is shorted to the ground, while that of transistor BC558 is connected to the positive terminal. The collector of transistor BC148 is connected to the base of BC558. The base of BC148 is connected to the washer (as shown in the figure).
The collector of BC558 is connected to pin 2 of musical IC UM66, and pin 3 of IC UM66 is shorted to the ground. The output from pin 1 is connected to a transistor amplifier comprising BEL187 transistor for feeding the loudspeaker. One end of 2.2-mega-ohm resistor R1 is connected to the positive rail and the
ing. Simultaneously, the emitter-baser junction of transistor BC558 also starts conducting. As a result, the collector of transistor BC558 is pulled towards the positive rail, which thus activates melody generator IC1 (UM66). The output of IC1 is amplified by transistor BEL187 and fed to the speaker. So we hear a musical note just by touching the touch points. The washers inner diameter should be 1 to 2 mm greater than that of the screwhead. The washer could be fixed in
other to a screw (as shown in the figure). The complete circuit is connected to a single pencil cell of 1.5V. When the touch-plate gap is bridged with a finger, the emitter-collector junction of transistor BC148 starts conduct-
the position by using an adhesive, while the screw can be easily driven in a wooden piece used for mounting the touch-plate. The use of brass washer and screw is recommended for easy solderability.
ELECTRONICS FOR YOU MARCH 2001
C I R C U I T
I D E A S
PRECISION AMPLIFIER WITH DIGITAL CONTROL

ANANTHA NARAYAN
EDI DWIV S.C.
his circuit is similar to the preceding circuit of the attenuator. Gain of up to 100 can be achieved in this configuration, which is useful for signal conditioning of low output of transducers in millivolt range. The gain selection resistors R3 to R6 can be selected by the user and can be anywhere from 1 kilo-ohm to 1 meg-ohm. Trimpots can be used for obtaining any value of gain required by the user. The resistor values shown in the circuit are for decade gains suitable for an autoranging DPM. Resistor R1 and capacitor C1 reduce ripple in the input and also snub transients. Zeners Z1 and Z2 limit the input to 4.7V, while the input current is limited by resistor R1. Capacitors C2 and C3 are the power supply decoupling capacitors. Op-amp IC1 is used to increase the input impedance so that very low in-
puts are not loaded on measurement. The user can terminate the inputs with resistance of his choice (such as 10 megohm or 1 meg-ohm) to avoid floating of the inputs when no measurement is being made. IC5 is used as an inverting buffer to restore polarity of the input while IC4 is used as buffer at the output of CD4052, because loading it by resistance of value less than 1 meg-ohm will cause an error. An alternative is to make R7=R8=1 meg-ohm and do away with IC4, though this may not be an ideal method.
Truth Table (Control Input vs Gain) X,Y (On-switch (2) (1) Gain Pair) B A (Av.) X0,Y0 0 0 1/10 X1,Y1 0 1 1 X2,Y2 1 0 10 X3,Y3 1 1 100
Gains greater than 100 may not be practical because even at gain value of 100 itself, a 100V offset will work out to be around 10 mV at the output (100V x 100). This can be trimmed using the offset null option in the OP07, connecting a trimpot between pins 1 and 8, and connecting wiper to +5V supply rails. For better performance, use ICL7650 (not pin-compatible) in place of OP07 and use 7.5V instead of 5V supply. Eight steps for gain or attenuation can be added by using two CD4051 and pin 6 inhibit on CD4051/52. More steps can be added by cascading many CD4051, or CD4052, or CD4053 ICs, as pin 6 works like a chip select. Some extended applications of this circuit are given below. 1. Error correction in transducer amplifiers by correcting gain. 2. Autoranging in DMM. 3. Sensor selection or input type selection in process control. 4. Digitally preset power supplies or electronic loads. 5. Programmable precision mV or mA sources. 6. PC or microcontroller or microprocessor based instruments. 7. Data loggers and scanners.
ELECTRONICS FOR YOU JANUARY 2001
C I R C U I T I D E A S CIR CUIT IDEAS
ADD-ON STEREO CHANNEL SELECTOR

PRABHASH K.P.
RUPANJANA
he add-on circuit presented here is useful for stereo systems. This circuit has provision for connecting stereo outputs from four different sources/channels as inputs and only one of them is selected/ connected to the output at any one time. When power supply is turned on, channel A (A2 and A1) is selected. If no audio is present in channel A, the circuit waits for some time and then selects the next channel (channel B), This search operation continues until it detects audio signal in one of the channels. The inter-channel wait or delay time can be adjusted with the help of preset VR1. If still longer time is needed, one may replace capacitor C1 with a capacitor of higher value. Suppose channel A is connected to a tape recorder and channel B is connected to a radio receiver. If initially
channel A is selected, the audio from the tape recorder will be present at the output. After the tape is played completely, or if there is sufficient pause between consecutive recordings, the circuit automatically switches over to the output from the radio receiver. To manually skip over from one (selected) active channel, simply push the skip switch (S1) momentarily once or more, until the desired channel inputs gets selected. The selected channel (A, B, C, or D) is indicated by the glowing of corresponding LED (LED11, LED12, LED13, or LED14 respectively). IC CD4066 contains four analogue switches. These switches are connected to four separate channels. For stereo operation, two similar CD4066 ICs are used as shown in the circuit. These analogue switches are controlled by IC CD4017 outputs. CD4017 is a 10-bit ring
counter IC. Since only one of its outputs is high at any instant, only one switch will be closed at a time. IC CD4017 is configured as a 4-bit ring counter by connecting the fifth output Q4 (pin 10) to the reset pin. Capacitor C5 in conjunction with resistor R6 forms a power-on-reset circuit for IC2, so that on initial switching on of the power supply, output Q0 (pin 3) is always high. The clock signal to CD4017 is provided by IC1 (NE555) which acts as an astable multivibrator when transistor T1 is in cut-off state. IC5 (KA2281) is used here for not only indicating the audio levels of the selected stereo channel, but also for forward biasing transistor T1. As soon as a specific threshold audio level is detected in a selected channel, pin 7 and/ or pin 10 of IC5 goes low. This low level is coupled to the base of transistor T1, through diode-resistor combination of D2-R1/D3-R22. As a result, transistor T1 conducts and causes output of IC1 to remain low (disabled) as long as the selected channel output exceeds the preset audio threshold level. Presets VR2 and VR3 have been included for adjustment of individual audio threshold levels of left stereo channels, as desired. Once the multivibrator action of IC1 is disabled, output of IC2 does not change further. Hence, search-
97
C I R C U I T
I D E A S
ing through the channels continues until it receives an audio signal exceeding the preset threshold value. The skip
switch S1 is used to skip a channel even if audio is present in the selected channel. The number of channels can be eas-
ily extended up to ten, by using additional 4066 ICs.
98
CIRCUIT
IDEAS
Telephone Number Display

BHASKAR BANERJEE
he given circuit, when connected in parallel to a telephone, displays the number dialled from the telephone set using the DTMF mode. This circuit can also show the number dialled from the phone of the called party. This is particularly helpful for receiving any number over the phone lines. The DTMF signalgenerated by the phone on dialling a numberis decoded by DTMF decoder CM8870P1 (IC1), which converts the received DTMF signal into its equivalent BCD number that corresponds to the dialled number. This binary number is stored sequentially in 10 latches each time a number is dialled from the phone. The first number is stored in IC5A (1/2 of CD4508) while the second number is stored in IC5B and so on. The binary output from IC1 for digit 0 as decoded by IC1 is 10102 (=1010), and this cannot be displayed by the seven-segment decoder, IC10. Therefore the binary output of IC1 is passed through a logic-circuit which converts an input of 10102 into 00002 without affecting the inputs 1 through 9. This is accomplished by gates N13 through N15 (IC11) and N1 (IC12). The storing of numbers in respective latches is done by IC2 (4017). The data valid output from pin 15 of IC1 is used to clock IC2. The ten outputs of IC2 are sequentially connected to the store and clear inputs of all the latches, except the last one, where the clear input is tied to ground. When an output pin of IC2 is high, the corresponding latch is cleared of previous data and kept ready for storing new data. Then, on clocking IC2, the same pin becomes low and the data present at the inputs of that latch at that instant gets stored and the next latch is cleared and kept ready. The similar input and output pins of all latches are connected together to
ELECTRONICS FOR YOU n MAY '99
R. R
AINA
CIRCUIT
form two separate input and output buses. There is only one 7-segment decoder/ driver IC10 for all the ten displays. This not only reduces size and cost but reduces power requirement too. The output from a latch is available only when its disable pins (3 and 15) are brought low. This is done by IC3, IC12 and IC13. IC3 is clocked by an astable multivibrator IC4 (555). IC3 also drives the displays by switching corresponding transistors. When a latch is enabled, its corresponding display is turned on and the content of that latch, after decoding by IC10, gets displayed in the corresponding display. For instance, contents of IC5A are displayed on display DIS1, that of IC5B on DIS2 and so on. The system should be connected to the telephone lines via a DPDT switch (not shown) for manual switching, otherwise any circuit capable of sensing handsets off-hook condition and thereby switching relays, etc. can be used for automatic switching. The power-supply switch can also be replaced then. Such circuits, under different captions, can be found in EFYs back issues. Though this circuit is capable of showing a maxi-
IDEAS
mum of ten digits, one can reduce the display digits as required. For doing this, connect the reset pin of IC2, say, for a 7-digit display, with S6 output at pin 5. The present circuit can be built on a veroboard and housed in a suitable box. The displays are common-cathode type. To make the system compact, small, 7segment displays can be used but with some extra cost. Also, different colour displays can be used for the first three or four digits to separate the exchange code/STD code, etc. The circuit can be suitably adopted for calling-line display.
ELECTRONICS FOR YOU n MAY '99
CIRCUIT
IDEAS
LUGGAGE SECURITY SYSTEM

DHURJATI SINHA
EDI DWIV S.C.
alarm sounds, connections to pin 1 and 6 may be made as per the table.
Select 1 Select 2 Sound effect (Pin6) (Pin1) X X Police siren VDD X Fire-engine siren VSS X Ambulance siren - VDD Machine-gun sound Note: X = no connection; - = do not care
hile travelling by a train or bus, we generally lock our luggage using a chain-and-lock arrangement. But, still we are under tension, apprehending that somebody may cut the chain and steal our luggage. Here is a simple circuit to alarm you when somebody tries to cut the chain. Transistor T1 enables supply to the sound generator chip when the base current starts flowing through it. When the wire (thin enameled copper wire of 30 to 40 SWG, used for winding transformers) loop around the chain is broken by somebody, the base of transistor T1, which was earlier tied to positive rail, gets opened. As a result, tran-
sistor T1 gets forward biased to extend the positive supply to the alarm circuit. In idle mode, the power consumption of the circuit is minimum and thus it can be used for hundreds of travel hours. To enable generation of different
86
C I R C U I T
I D E A S
UNIVERSAL HIGH-RESISTANCE VOLTMETER

YOGESH KATARIA
I VED DWI S.C.
TABLE I Position 1 of Function Switch

Edc input 5.00V 4.00V 3.00V 2.00V 1.00V Meter Current 44 A 34 A 24 A 14 A 4 A
he full-scale deflection of the universal high-input-resistance voltmeter circuit shown in the figure
depends on the function switch position as follows: (a) 5V DC on position 1 (b) 5V AC rms in position 2 (c) 5V peak AC in position 3 (d) 5V AC peak-to-peak in position 4 The circuit is basically a voltage-tocurrent converter. The design procedure is as follows:
Calculate RI according to the application from one of the following equations: (a) DC voltmeter: RIA = full-scale EDC/IFS (b) RMS AC voltmeter (sine wave only): RIB = 0.9 full-scale ERMS/ IFS (c) Peak reading voltmeter (sine wave only): RIC = 0.636 fullscale EPK/IFS (d) Peak-to-peak AC voltmeter (sine wave only): RID = 0.318 full-scale EPK-TO-PK / IFS The term IFS in the above equations refers to meters fullscale deflection current rating in amperes. It must be noted that neither meter resistance nor diode voltage drops affects meter current. Note: The results obtained during practical testing of the circuit in EFY lab are tabulated in Tables I through IV. A high-input-resistance op-amp, a bridge rectifier, a microammeter, and a few other discrete components are all that are required to realise this versatile circuit. This circuit can be used for measurement of DC, AC RMS, AC peak, or AC peak-to-peak voltage by simply chang-
TABLE II Position 2 of Function Switch

Erms input 5V 4V 3V 2V 1V Meter Current 46 A 36 A 26 A 18 A 10 A
TABLE III Position 3 of Function Switch

EPk input 5V peak 4V peak 3V peak 2V peak 1V peak Meter Current 46 A 36 A 26 A 16 A 6 A
TABLE IV Position 4 of Function Switch

EPk-To-Pk 5V peak to peak 4V peak to peak 3V peak to peak 2V peak to peak 1V peak to peak Meter Current 46 A 36 A 26 A 16 A 7 A
ing the value of the resistor connected between the inverting input terminal of the op-amp and ground. The voltage to be measured is connected to non-inverting input of the op-amp.
CIRCUIT
IDEAS
Time Switch
AVNISH PUNDIR
ATA Y. K
RIA
his circuit is especially designed for those who often need to wake up early in the morning. Ordinary alarms in electronic watches are not loud enough and very often they fail to wake up. The switch circuit described here will come handy; it can be used to switch on a TV, radio or tape recorder etc, which will not allow even the laziest amongst us to ignore their sound for too long. Besides, this time switch can also be used to
out having to flip the mode switch (i.e. mode switch can be omitted). Please refer to the back panel diagram of a typical analogue clock and the audio jack, to see how the existing buzzer of the clock is required to be wired to the audio output from the clock. This will ensure that when plug is inserted in the audio jack, the clocks buzzer will remain off and not consume any power
the position of mode switch. At the time of alarm, when point A connected to collector of transistor T1 passes through logic 0 state, the output logic state of both the gates will toggle. Assuming that mode switch is flipped to Mode Off position at poweron-reset (when point D is at logic 1), initially diode D1 would be in blocking state and transistor T2 would be forward biased via resistor R5 and diodes D2 and D3. As a result, the relay is in energised state, which makes output power available at output socket1 and cuts it off from socket-2. At alarm time, the audio signal toggles logic output states of both gates N1 and N2. As a result, point D goes to logic 0 state. Diode D1 conducts, taking the voltage at junction of diodes D1 and D2 to near about 1 volt. Diode D3 ensures that its series combination with
switch on/off any other electric or electronic gadget at any time. What you need is a simple analogue electronic clock with alarm facility and a small circuit to implement the time switch. This time switch has two modes. One is time-on mode and the other is time-off mode. In time-on mode, you set up the alarm in your clock as per normal procedure and at the set time this switch turns on the gadget connected at the output socket-1. In timeoff mode, it turns your gadget off at the set time. The optional output socket-2 is wired in such a way that when you use this socket, the mode changes with-
unnecessarily. The audio alarm output from the clock is coupled to the AF detector built around low-power switching transistor T1. During alarm, the collector of transistor T1 will fluctuate around ground level and Vcc. During absence of audio alarm input, the collector of transistor T1 is held at Vcc potential. The next stage consists of an S-R latch built around NAND gates N1 and N2. Capacitor C2 and resistor R4 are used for power-on-reset. On switching the power supply, gate N2 output will acquire logic 1 and that of gate N1 logic 0. This is the initial state, irrespective of
ELECTRONICS FOR YOU n MARCH '99
diode D2 puts them in blocking mode. Capacitor C3 meanwhile discharges via resistor R6 and the voltage at base of transistor T2 approaches towards ground level, cutting off transistor T2 and de-energising relay RL1. Now the power at output socket-1 would be cut off while it becomes available in socket-2. If the above operation is repeated with switch S1 in Mode On, the power would initially not be available in socket-1 (but available in socket-2). But after the alarm, the power would become available in socket-1 and not in socket-2.
CIRCUIT
IDEAS
Infrared Cordless Headphone

PRADEEP G.
OO SAG G.S.
sing this low-cost project one can reproduce audio from TV without disturbing others. It does not use any wire connection between TV and headphones. In place of a pair of wires, it uses invisible infrared light to transmit audio signals from
TV to headphones. Without using any lens, a range of up to 6 metres is
possible. Range can be extended by using lenses and reflectors with IR sensors comprising transmitters and receivers. IR transmitter uses two-stage transistor amplifier to drive two series-connected IR LEDs. An audio output transformer is used (in reverse) to couple audio output from TV to the IR transmitter. Transistors T1 and T2 amplify the audio signals received from TV through the audio transformer. Lowimpedance output windings (lower
gauge or thicker wires) are used for connection to TV side while high-impedance windings are connected to IR transmitter. This IR transmitter can be powered from a 9-volt mains adapter or battery. Red LED1 in transmitter circuit functions as a zener diode (0.65V) as well as supply-on indicator. IR receiver uses 3-stage transistor amplifier. The first two transistors (T4 and T5) form audio signal amplifier while the third transistor T6 is used to drive a headphone. Adjust potmeter VR2 for max. clarity. Direct photo-transistor towards IR LEDs of transmitter for max. range. A
9-volt battery can be used with receiver for portable operation.
ELECTRONICS FOR YOU n AUGUST '99
CIRCUIT
IDEAS
Dual-Channel Digital Volume Control

SHEENA K.
his circuit could be used for replacing your manual volume control in a stereo amplifier. In this circuit, push-to-on switch S1 controls the forward (volume increase) operation of both channels while a similar switch S2 controls reverse (volume decrease) operation of both channels. Here IC1 timer 555 is configured as an astable flip-flop to provide low-freN ILLO . DH A.P.S
quency pulses to up/down clock input pins of pre-setable up/down counter 74LS193 (IC2) via push-to-on switches S1 and S2. To vary the pulse width of pulses from IC1, one may replace timing resistor R1 with a variable resistor. Operation of switch S1 (up) causes the binary output to increment while operation of S2 (down) causes the binary output to decrement. The maxi-
mum count being 15 (all outputs logic 1) and minimum count being 0 (all outputs logic 0), it results in maximum and minimum volume respectively. The active high outputs A, B, C and D of the counter are used for controlling two quad bi-polar analogue switches in each of the two CD4066 ICs (IC3 and IC4). Each of the output bits, when high, short a part of the resistor network comprising series resistors R6 through R9 for one channel and R10 through R13 for the other channel, and thereby control the output of the audio signals being fed to the inputs of stereo amplifier. Push-to-on switch S3 is used for resetting the output of counter to 0000, and thereby turning the volume of both channels to the minimum level.
ELECTRONICS FOR YOU n AUGUST '99
CIRCUIT
IDEAS
Simple Low-Cost Digital Code Lock

A. JEYABAL
RUP ANJA NA
any digital code lock circuits have been published in this magazine. In those circuits a set of switches (conforming to code) are pressed one by one within the specified time to open the lock. In some other circuits, custom-built ICs are used and positive and negative logic pulses are
An essential property of this electronic code lock is that it works in monostable mode, i.e. once triggered, the output becomes high and remains so for a period of time, governed by the timing components, before returing to the quiescent low state. In this circuit, timer IC 555 with 8 pins is used. The
R4, and on releasing these two switches, capacitor C3 starts discharging through resistor R4. Capacitor C3 and resistor R4 are so selected that it takes about five seconds to fully discharge C3. Depressing switches S1 and S8 in unison, within five seconds of releasing the switches SA and SC, pulls pin 2 to ground and IC 555 is triggered. The capacitor C1 starts charging through resistor R1. As a result, the output (pin 3) goes high for five seconds (i.e. the charging time T of the capacitor C1 to the threshold voltage, which is calculated by the relation T=1.1 R1 x C1 seconds). Within these five seconds, switches SA and SC are to be pressed momentarily once again, followed by the depression of last code-switch pair S3-S4.
keyed in sequence as per the code by two switches to open the lock. A low-cost digital code lock circuit is presented in this article. Here the keying-in code is rather unique. Six switches are to be pressed to open the lock, but only two switches at a time. Thus a total of three sets of switches have to be pressed in a particular sequence. (Of these three sets, one set is repeated.) The salient features of this circuit are: 1. Use of 16 switches, which suggests that there is a microprocessor inside. 2. Elimination of power amplifier transistor to energise the relay. 3. Low cost and small PCB size.
IC is inexpensive and easily available. Its pin 2 is the triggering input pin which, when held below 1/3 of the supply voltage, drives the output to high state. The threshold pin 6, when held higher than 2/3 of the supply voltage, drives the output to low state. By applying a low-going pulse to the reset pin 4, the output at pin 3 can be brought to the quiescent low level. Thus the reset pin 4 should be held high for normal operation of the IC. Three sets of switches SA-SC, S1S8 and S3-S4 are pressed, in that order, to open the lock. On pressing the switches SA and SC simultaneously, capacitor C3 charges through the potential divider comprising resistors R3 and
These switches connect the relay to output pin 3 and the relay is energised. The contacts of the relay close and the solenoid pulls in the latch (forming part of a lock) and the lock opens. The remaining switches are connected between reset pin 4 and ground. If any one of these switches is pressed, the IC is reset and the output goes to its quiescent low state. Possibilities of pressing these reset switches are more when a code breaker tries to open the lock. LED D5 indicates the presence of power supply while resistor R5 is a current limiting resistor. The given circuit can be recoded easily by rearranging connections to the switches as desired by the user.
ELECTRONICS FOR YOU n JULY '99
CIRCUIT
IDEAS
Electronic Jam
RAJESH K.P.
N ILLO . DH A.P.S
his jam circuit can be used in quiz contests wherein any participant who presses his button (switch) before the other contestants, gets the first chance to answer a question. The circuit given here permits up to eight contestants with each one allotted a distinct number (1 to 8). The display will show the number of the contestant pressing his button before the others. Simultaneously, a buzzer will also sound. Both, the display as well as the buzzer have to be reset manually using a common reset switch. Initially, when reset switch S9 is momentarily pressed and released, all outputs of 74LS373 (IC1) transparent latch go high since all the input data lines are returned to Vcc via resistors R1
through R8. All eight outputs of IC1 are connected to inputs of priority encoder 74LS147 (IC2) as well as 8-input NAND gate 74LS30 (IC3). The output of IC3 thus becomes logic 0 which, after inversion by NAND gate N2, is applied to latch-enable pin 11 of IC1. With all input pins of IC2 being logic 1, its BCD output is 0000, which is applied to 7segment decoder/driver 74LS47 (IC6) after inversion by hex inverter gates inside 74LS04 (IC5). Thus, on reset the display shows 0. When any one of the push-to-on switchesS1 through S8is pressed, the corresponding output line of IC1 is latched at logic 0 level and the display indicates the number associated with the specific switch. At the same time,
output pin 8 of IC3 becomes high, which causes outputs of both gates N1 and N2 to go to logic 0 state. Logic 0 output of gate N2 inhibits IC1, and thus pressing of any other switch S1 through S8 has no effect. Thus, the contestant who presses his switch first, jams the display to show only his number. In the unlikely event of simultaneous pressing (within few nano-seconds difference) of more than one switch, the higher priority number (switch no.) will be displayed. Simultaneously, the logic 0 output of gate N1 drives the buzzer via pnp transistor BC158 (T1). The buzzer as well the display can be reset (to show 0) by momentary pressing of reset switch S9 so that next round may start. Lab Note: The original circuit sent by the author has been modified as it did not jam the display, and a higher number switch (higher priority), even when pressed later, was able to change the displayed number.
ELECTRONICS FOR YOU n JUNE '99
CIRCUIT IDEAS
figure. The 1kHz signal can be further divided using decade counters to generate the required time period. EFY lab note. To generate required gate for use in a frequency counter circuit, the final oscillator output needs to be followed by a toggle flip-flop. For example, a 1kHz clock, when applied to a toggle flip-
CRYSTAL-CONTROLLED TIME-BASE GENERATOR

PRATAP CHANDRA SAHU
I VED DWI S.C.
digital frequency counter needs a time-base generator to count the frequency with high resolution. Normally, a crystal-based oscillator with divider IC chain or a similar circuit in the form of an ASIC (application-specific IC) is used for time-base generation. Here weve presented a simple circuit for accurate time-base generation using the readily available 3.5795MHz crystal commonly used in telecommunication equipment. The 3.5795MHz crystal is used in conjunction with a CD4060-based crystal oscillator-cum-divider (IC1). The crystal frequency is divided by 512 by IC1, which is further divided by 7 by CD4017 (IC2). IC2 is reset as soon as its Q7 output goes high.
Thus the crystal frequency is divided by 3584, giving the final output frequency of around 998.8 Hz. This frequency can be trimmed to exactly 1 kHz with the help of trimmer capacitor VC1 as shown in the
flop, will generate gates with 1-sec on period and 1-sec off period. This circuit is estimated to cost below Rs 50.
ELECTRONICS FOR YOU
MAY 2002
CIRCUIT IDEAS
MAINS-OPERATED CHRISTMAS STAR

PRINCE PHILLIPS
O I THE SAN
ere is a low-cost circuit of Christmas star that can be easily constructed even by a novice. The main
advantage of this circuit is that it doesnt require any step-down transformer or ICs. Components like resistors R1 and R2,
capacitors C1, C2, and C3, diodes D1 and D2, and zener ZD1 are used to develop a fairly steady 5V DC supply voltage that provides the required current to operate the multivibrator circuit and trigger triac BT136 via LED1. The multivibrator circuit is constructed using two BC548 transistors (T1 and T2) and some passive components. The frequency of the multivibrator circuit is controlled by capacitors C4 and C5 and resistors R3 through R7. The output of the multivibrator circuit is connected to transistor T3, which, in turn, drives the triac via LED1. During positive half cycles of the multivibrators output, transistor T3 energises triac BT136 and the lamp glows. This circuit is estimated to cost Rs 75.
MAY 2002
ELECTRONICS FOR YOU
C CU T IIT D EIAD SEAS CIIRR CIU
MAINS MANAGER
SHIBASHISH PATEL
SUN
IL KU
MAR
ery often we forget to switch off the peripherals like monitor, scanner, and printer while switching off our PC. The problem is that there are separate power switches to turn the peripherals off. Normally, the peripherals are connected to a single of those four-way trailing sockets that are plugged into a single wall socket. If that socket is accessible, all the devices could be switched off from there and none of the equipment used will require any modification. Here is a mains manager circuit that allows you to turn all the equipment on or off by just operating the switch on any one of the devices; for example, when you switch off your PC, the monitor as well as other equipment will get powered down automatically. You may choose the main equipment to control other gadgets. The main equipment is to be directly plugged into the master socket, while all other equipment are to be connected via the slave socket. The mains supply from the wall socket is to be connected to the input of the mains manager circuit. The unit operates by sensing the current drawn by the control equipment/load from the master socket. On sensing that the control equipment is on, it powers up the other (slave) sockets. The load on the master socket can be anywhere between 20 VA and 500 VA, while the load on the slave sockets can be 60 VA to 1200 VA. During the positive half cycle of the mains AC supply, diodes D4, D5, and D6 have a voltage drop of about 1.8 volts when current is drawn from the master socket. Diode D7 carries the current during negative half cycles. Capacitor C3, in series with diode D3, is connected across the diode combination of D4 through D6, in addition to diode D7 as well as resistor R10. Thus current pulses during positive half-cycles, charge up the capacitor to 1.8
volts via diode D3. This voltage is sufficient to hold transistor T2 in forward biased condition for about 200 ms even after the controlling load on the master socket is switched off. When transistor T2 is on, transistor T1 gets forward biased and is switched on. This, in turn, triggers Triac 1, which then powers the slave loads. Capacitor C4 and resistor R9 form a snubber network to ensure that the triac turns off cleanly with an inductive load.
possible, plug the unit into the mains via an earth leakage circuit breaker. The mains LED1 should glow and the slave LED2 should remain off. Now connect a table lamp to the master socket and switch it on. The lamp should operate as usual. The slave LED should turn on whenever the lamp plugged into slave socket is switched on. Both lamps should be at full brightness without any flicker. If so, the unit is working correctly and can be put into use.
LED1 indicates that the unit is operating. Capacitor C1 and zener ZD1 are effectively in series across the mains. The resulting 15V pulses across ZD1 are rectified by diode D2 and smoothened by capacitor C2 to provide the necessary DC supply for the circuit around transistors T1 and T2. Resistor R3 is used to limit the switching-on surge current, while resistor R1 serves as a bleeder for rapidly discharging capacitor C1 when the unit is unplugged. LED1 glows whenever the unit is plugged into the mains. Diode D1, in anti-parallel to LED1, carries the current during the opposite half cycles. Dont plug anything into the master or slave sockets without testing the unit. If
Note. 1. The device connected to the master socket must have its power switch on the primary side of the internal transformer. Some electronic equipment have the power switch on the secondary side and hence these devices continue to draw a small current from the mains even when switched off. Thus such devices, if connected as the master, will not control the slave units correctly. 2. Though this unit removes the power from the equipment being controlled, it doesnt provide isolation from the mains. So, before working inside any equipment connected to this unit, it must be unplugged from the socket.
CIRCUIT
IDEAS
AUTO SHUT-OFF FOR CASSETTE PLAYERS AND AMPLIFIERS

ARTHUR LOUIS
MAR IL KU SUN
ere are two simple, low-cost circuits that can be used to shut off the mains supply to any audio or video equipment (such as tape recorder, CD player, and amplifier). These circuits are helpful to those in the habit of falling asleep with their music system on. The circuits will also protect the equipment from getting damaged due to highvoltage spikes whenever there is a resumption of power after a break. This is possible because the equipment will get switched off automatically under such conditions but will not get switched on automatically on resumption of mains supply. The circuit in Fig. 1 can be used to shut off any cassette player that has a reliable auto-stop mechanism. Whenever switch S1 is pressed momentarily, it extends the supply to the step-down transformer of the tape recorder and charges capacitor C1 through diode D1. This, in turn, makes transistor T1 conduct and energise relay RL1 to provide a parallel path to switch S1, so that supply to the step-down transformer continues even when switch S1 is released. When any button on the cassette player is pressed, the capacitor charges through diode D2. This ensures conduction of transistor T1 and thus the continuity of operation of cassette player. However, whenever the auto-stop mechanism functions at the end of a tape, the leaf switch gets opened. This cuts the charging path for the capacitor and it starts discharging slowly. After about one minute, the relay opens and interrupts main power to the transformer. The time delay can be increased by increasing the value of capacitor C1. If the appliance used is a two-in-one type (e.g. cassette player-cum-radio), just connect another diode in parallel with diodes D1 and D2 to provide an additional path for charging capacitor C1 via the tape-to-radio changeover switch, so that when radio is played the relay does not
interrupt the power supply. The other circuit, shown in Fig. 2, functions on the basis of the signal received from preamp of the appliance used. In this circuit, opamp A741 is wired in inverting opamp configuration. It amplifies the signal received from the preamp. Timer NE555 is used to provide the necessary time delay of about one minute. Preset VR1 is used to control the sensitivity of the circuit to differentiate be-
tween the noise and the signal. Resistor R4 offers feedback resistance to control the gain of the opamp. By increasing or decreasing the value of resistor R4, the gain can be increased or decreased, respectively. The preset time delay of timer NE555 (which is about one minute) can be increased by increasing the value of C4. Initial energisation of relay RL2 and charging of capacitor C4 take place on depression of switch S3 in the same manner as charging of capacitor C1 (refer Fig. 1) on depression of switch S1. As a result, pins 2 and 6 of NE555 go high and the output of timer goes low to switch off mains supply from the relay to step-down transformer X2 of the appliance. Bleeder resistor R6 is used to discharge capacitor C4. Now if signals are received from the
ELECTRONICS FOR YOU APRIL 2001
CIRCUIT
IDEAS
preamplifier, these are amplified by 741 and fed to the base of transistor T2, which keeps capacitor C4 charged through resistor R5. When there is no signal, T2 will not conduct and the capacitor slowly discharges through R6. The output of 555 goes high to switch off the relay and thus
the mains supply to transformer X2. Switch S2 can be depressed momentarily if the device needs to be manually switched off. Note. The 12V supply should be provided to the circuit from the equipments power supply. Opamp 741 should be
driven from the preamplifier of the gadget used, and not from its power amplifier output. Switches S1 and S2 are 2pole push-to-on switches. These can also be fabricated from 2-pole on-off switches, which are widely used in cassette players, by removing the latch pin from them.
CIRCUIT
IDEAS
CONDENSER MIC AUDIO AMPLIFIER

D. PRABAKARAN
he compact, low-cost condenser mic audio amplifier described here provides good-quality audio of 0.5 watts at 4.5 volts. It can be used as part of intercoms, walkie-talkies, low-power
MAR IL KU N U S
transmitters, and packet radio receivers. Transistors T1 and T2 form the mic preamplifier. Resistor R1 provides the necessary bias for the condenser mic while preset VR1 functions as gain control for
varying its gain. In order to increase the audio power, the low-level audio output from the preamplifier stage is coupled via coupling capacitor C7 to the audio power amplifier built around BEL1895 IC. BEL1895 is a monolithic audio power amplifier IC designed specifically for sensitive AM radio applications that delivers 1 watt into 4 ohms at 6V power supply voltage. It exhibits low distortion and noise and operates over 3V-9V supply voltage, which makes it ideal for battery operation. A turn-on pop reduction circuit prevents thud when the power supply is switched on. Coupling capacitor C7 determines low-frequency response of the amplifier. Capacitor C9 acts as the ripple-rejection filter. Capacitor C13 couples the output available at pin 1 to the loudspeaker. R15-C13 combination acts as the damping circuit for output oscillations. Capacitor C12 provides the boot strapping function. This circuit is suitable for lowpower HAM radio transmitters to supply the necessary audio power for modulation. With simple modifications it can also be used in intercom circuits.
ELECTRONICS FOR YOU DECEMBER 2001
CIRCUIT IDEAS
CONTACTLESS RINGER FOR TELEPHONES

PRADEEP G.
EDI DWIV S.C.
everal circuits of a telephone extension ringer have earlier been published in EFY. The circuit presented here is distinct from these circuits in that it has no electrical contact with the telephone lines. It senses the induced fluctuating electric field of telephone lines when the phone rings. The input is sensed by a 5-8cm long plastic insulated flexible wire that is wound 3-4 times on telephone cable. When the telephone rings, about 20Hz AC voltage is available on the telephone line, which causes field fluctuation up to a few centimetres outside the telephone cable also. The 20Hz AC signal induced in the pick-up sensor is coupled to the clock pin of decade counter IC CD4017. The CD4017 is wired as a divide-by-two counter by connecting its pin 4 to reset pin 15. As the input impedance of CMOS IC is extremely high, the induced electric field is sufficient to clock it. The output obtained at pin 3 of CD4017 is a 10Hz square wave (half of input 20Hz signals). This square wave signal is used to bias npn
transistor BC547 in class-C mode of operation. The transistor conducts during the positive half cycle of square wave. The positive voltage (high) available at the emitter of the transistor pulls reset pin 4 of 555 timer IC high for the correspond-
ing duration. As a result, the alarm is activated when the telephone rings. When the handset is picked up or the telephone stops ringing, the transistor stops conduction. Then reset pin of IC2 goes low and the alarm is disabled.
JUNE 2002
ELECTRONICS FOR YOU
CIRCUIT IDEAS
EXCLUSIVE-OR GATE APPLICATIONS

ANAND TAMBOLI
EDI DWIV S.C.
OR gate is a derived logic gate that finds many applications in digital circuits. Here we have described use of XOR gate as controlled inverter, 9s BCD subtractor and up-/down-counter. It can be seen from Fig. 1 and the accompanying truth table that XOR gate works as NOT (inverter) gate when its one input is held high, and as a buffer when the same input is pulled low. The common input (as shown in Fig. 2) can
therefore be used as control input for XOR gates to behave as inverters or buffers. Here one of the inputs of each XOR gate are connected
TRUTH TABLE I XOR Gate A B Y 0 0 0 0 1 1 1 0 1 1 1 0
Fig. 1: XOR gate as inverter and buffer
Fig. 2: XOR gate as controlled inverter
Fig. 4: Up-/down-counter
subtraction circuits using 1s and 2s complements. In another configuration of XOR gate shown in Fig. 3, the circuit works as a 9s BCD subtractor. Its output=9 input. The circuit in Fig. 3 can be used as a down-counter when employed with 4-bit BCD counter IC 7490 as shown in Fig. 4. Truth table of this configuration is given alongside. As seen from the figure, this circuit can be built using a single XOR-IC (TTLTRUTH TABLE II Down-Counter DEC. EQ. D0C0B0A0 0 1001 1 1000 2 0111 3 0110 4 0101 5 0100 6 0011 7 0010 8 0001 9 0000
Fig. 3: XOR gate as 9s BCD subtractor
together to serve as the control signal, while the remaining inputs serve as input bits. When control signal is zero, the output is same as the input (buffer mode). However, when control signal is held high, all bits are inverted. Thus the output is complement of the input. This complementing function is useful in
DiCiBiAi 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001
DEC. EQ. 9 8 7 6 5 4 3 2 1 0
7486). The NOR gate used in the circuit is inevitable, but it can be replaced by a resistance-transistor logic (RTL) circuit or any other equivalent circuit.
ELECTRONICS FOR YOU
JUNE 2002
CIRCUIT
IDEAS
FASTEST FINGER FIRST INDICATOR

P. RAJESH BHAT
uiz-type game shows are increasingly becoming popular on television these days. In such games, fastest finger first indicators (FFFIs) are used to test the players reaction time. The players designated number is displayed with an audio alarm when the player presses his entry button.
EDI DWIV S.C.
When a contestant presses his switch, the corresponding output of latch IC2 (7475) changes its logic state from 1 to 0. The combinational circuitry comprising dual 4-input NAND gates of IC3 (7420) locks out subsequent entries by producing the appropriate latch-disable signal. Priority encoder IC4 (74147) encodes
anode 7-segment LED display (DIS.1, FND507 or LT543). The audio alarm generator comprises clock oscillator IC7 (555), whose output drives a loudspeaker. The oscillator frequency can be varied with the help of preset VR1. Logic 0 state at one of the outputs of IC2 produces logic 1 input condition at pin 4 of IC7, thereby enabling the audio oscillator. IC7 needs +12V DC supply for sufficient alarm level. The remaining circuit operates on regulated +5V DC supply, which is obtained using IC1 (7805). Once the organiser identifies the con-
The circuit presented here determines as to which of the four contestants first pressed the button and locks out the remaining three entries. Simultaneously, an audio alarm and the correct decimal number display of the corresponding contestant are activated.
the active-low input condition into the corresponding binary coded decimal (BCD) number output. The outputs of IC4 after inversion by inverter gates inside hex inverter 74LS04 (IC5) are coupled to BCDto-7-segment decoder/display driver IC6 (7447). The output of IC6 drives common-
testant who pressed the switch first, he disables the audio alarm and at the same time forces the digital display to 0 by pressing reset pushbutton S5. With a slight modification, this circuit can accommodate more than four contestants.
ELECTRONICS FOR YOU DECEMBER 2001
CIRCUIT IDEAS
FM BOOSTER
PRADEEP G.
MAR IL KU SUN
ere is a low-cost circuit of an FM booster that can be used to listen to programmes from distant FM
stations clearly. The circuit comprises a common-emitter tuned RF preamplifier wired around VHF/UHF transistor
2SC2570. (Only C2570 is annotated on the transistor body.) Assemble the circuit on a good-quality PCB (preferably, glass-epoxy). Adjust input/output trimmers (VC1/VC2) for maximum gain. Input coil L1 consists of four turns of 20SWG enamelled copper wire (slightly space wound) over 5mm diameter former. It is tapped at the first turn from ground lead side. Coil L2 is similar to L1, but has only three turns. Pin configuration of transistor 2SC2570 is shown in the figure.
ELECTRONICS FOR YOU
FEBRUARY 2002
C CU T IIT D EIAD SEAS CIIRR CIU
MUSIC-ON-HOLD FOR TELEPHONES

SIBIN K. ZACHARIAH
EDI DWIV S.C.
ere is a simple circuit for musicon-hold with automatic shut off facility. During telephone conversation if you are reminded of some urgent work, momentarily push switch S1 until red LED1 glows, keep the telephone handset on the cradle, and attend to the work on hand. A soft music is generated and passed into the telephone lines while the other-end subscriber holds. When you return, you can simply pick up the handset again and continue with the conversation. The glowing of LED1, while the music is generated, indicates that the telephone is in hold position. As soon as the handset is picked up, LED1 is turned off and the music stops. Normally, the voltage across telephone lines is about 50 volts. When we pick up the receiver (handset), it drops to about 9 volts. The minimum voltage required to activate this circuit is about 15 volts. If the voltage is less than 15 volts, the circuit automatically switches off. However, initially both transistors T1 and T2 are cut off. The transistor pair of T1 and T2 performs switching and latching action when switch S1 is momentarily pressed, provided the
line voltage is more than 15 volts, i.e. when the handset is placed on the cradle. Once the transistor pair of TI and T2 starts conducting, melody generator IC1
minals of pnp transistor T1) develops enough voltage to forward bias transistor T1 and it starts conducting. As a consequence, output voltage at the collector of transistor T1 sustains forward biasing of transistor T2, even if switch S1 is released. This latching action keeps both transistors T1 and T2 in conduction as long as the output of the bridge rectifier is greater than 15 volts. If the handset is now lifted off-hook, the rectifier output drops to about 9 volts and hence latching action ceases and the
gets the supply and is activated. The music is coupled to the telephone lines via capacitor C2, resistor R1, and the bridge rectifier. With the handset off-hook after a ring, momentary depression of switch S1 causes forward biasing of transistor T2. Meanwhile, if the handset is placed on the cradle, the current passing through R1 (connected across the emitter and base ter-
circuit automatically switches off. (EFY lab note. The value of resistor R2 determines the current through resistor R1 to develop adequate voltage (greater than 0.65 volts) for conduction of transistor T1. Hence it may be test selected between 33 kilo-ohms and 100 kilo-ohms to obtain instant latching.) The total cost of this circuit is around Rs 50.
ELECTRONICS FOR YOU
APRIL 2002
CIRCUIT
IDEAS
INVISIBLE BROKEN WIRE DETECTOR

K. UDHAYA KUMARAN, VU3GTH
EDI DWIV . C . S
ortable loads such as video cameras, halogen flood lights, electrical irons, hand drillers, grinders, and cutters are powered by connecting long 2- or 3-core cables to the mains plug. Due to prolonged usage, the power cord wires are subjected to mechanical strain and stress, which can lead to internal snapping of wires at any point. In such a case most people go for replacing the core/cable, as finding the exact loca-
tion of a broken wire is difficult. In 3-core cables, it appears almost impossible to detect a broken wire and the point of break without physically disturbing all the three wires that are concealed in a PVC jacket. The circuit presented here can easily and quickly detect a broken/faulty wire and its breakage point in 1-core, 2-core, and 3-core cables without physically disturbing wires. It is built using hex inverter CMOS CD4069. Gates N3 and N4 are used as a pulse generator that oscillates at around 1000 Hz in audio range.
The frequency is determined by timing components comprising resistors R3 and R4, and capacitor C1. Gates N1 and N2 are used to sense the presence of 230V AC field around the live wire and buffer weak AC voltage picked from the test probe. The voltage at output pin 10 of gate N2 can enable or inhibit the oscillator circuit. When the test probe is away from any high-voltage AC field, output pin 10 of gate N2 remains low. As a result, diode D3 conducts and inhibits the oscillator circuit from oscillating. Simultaneously, the output of gate N3 at pin 6 goes low to cut off transistor T1. As a result, LED1 goes off. When the test probe is moved closer to 230V AC, 50Hz mains live wire, during every positive halfcycle, output pin 10 of gate N2 goes high. Thus during every positive half-cycle of the mains frequency, the oscillator circuit is allowed to oscillate at around 1 kHz, making red LED (LED1) to blink. (Due to the persistence of vision, the LED appears to be glowing continuously.) This type of blinking reduces consumption of the current from button cells used for power supply. A 3V DC supply is sufficient for powering the whole circuit. AG13 or LR44 type button cells, which are also used inside laser pointers or in LED-based continuity testers, can be used for the circuit. The circuit consumes 3 mA during the sensing of AC mains voltage.
For audio-visual indication, one may use a small buzzer (usually built inside quartz alarm time pieces) in parallel with one small (3mm) LCD in place of LED1 and resistor R5. In such a case, the current consumption of the circuit will be around 7 mA. Alternatively, one may use two 1.5V R6- or AA-type batteries. Using this gadget, one can also quickly detect fused small filament bulbs in serial loops powered by 230V AC mains. The whole circuit can be accommodated in a small PVC pipe and used as a handy broken-wire detector. Before detecting broken faulty wires, take out any connected load and find out the faulty wire first by continuity method using any multimeter or continuity tester. Then connect 230V AC mains live wire at one end of the faulty wire, leaving the other end free. Connect neutral terminal of the mains AC to the remaining wires at one end. However, if any of the remaining wires is also found to be faulty, then both ends of these wires are connected to neutral. For single-wire testing, connecting neutral only to the live wire at one end is sufficient to detect the breakage point. In this circuit, a 5cm (2-inch) long, thick, single-strand wire is used as the test probe. To detect the breakage point, turn on switch S1 and slowly move the test probe closer to the faulty wire, beginning with the input point of the live wire and proceeding towards its other end. LED1 starts glowing during the presence of AC voltage in faulty wire. When the breakage point is reached, LED1 immediately extinguishes due to the non-availability of mains AC voltage. The point where LED1 is turned off is the exact broken-wire point. While testing a broken 3-core rounded cable wire, bend the probes edge in the form of J to increase its sensitivity and move the bent edge of the test probe closer over the cable. During testing avoid any strong electric field close to the circuit to avoid false detection.
ELECTRONICS FOR YOU AUGUST 2001
I RICT U II T DI E DE C I R CC U AASS
IR REMOTE SWITCH
K.S. SANKAR
EDI DWIV S.C.
magine the convenience of selecting TV channels using your remote and then pointing the same remote to your switchboard to switch on/off the fan or the tubelight. Here is a simple circuit to remotely switch on/off any electrical device through a relay using the normal TV/ VCR/VCP/VCD remote control unit. It
works up to a distance of about 10 metres. The circuit is built around a 3-pin IR IC receiver (Siemens SFH-506-38 or equivalent) that can detect 38kHz burst frequency generated by a TV remote. (This IR receiver module has been covered earlier in many projects published in EFY.) The output pin of IR sensor goes low
when it detects IR light, triggering the monostable (1-second) built around timer NE555. The output of the mono toggles the J-K flip flop, whose Q output drives the relay through SL100 npn transistor (T1). LED2, LED3, and LED4 are used to display the status of each output stage during circuit operation. Back-EMF diode D5 is used for protection. Transistor T1 is configured as an open-collector output device to drive the relay rated at 12V DC. The circuit draws the power from voltage regulator 7805. Capacitor C5 is soldered close to the IR sensors pins to avoid noise and false triggering. Capacitor C3 and resistor R3 also avoid false triggering of monostable NE555. The monostable acts as a 1-second hysterisis unit to restrict the flipflop from getting retriggered within one second. To activate any other 12V logic device, use the output across the relay coil terminals.
MARCH 2002
ELECTRONICS FOR YOU
CIRCUIT IDEAS
LASER TORCH-BASED VOICE TRANSMITTER AND RECEIVER

PRADEEP G.
SAN
I THE
sing this circuit you can communicate with your neighbours wirelessly. Instead of RF signals, light from a laser torch is used as the carrier in the circuit. The laser torch can transmit light up to a distance of about 500 metres. The phototransistor of the receiver must be accurately oriented towards the laser beam from the torch. If there is any obstruction in the path of the laser beam, no sound will be heard from the receiver. The transmitter circuit (Fig. 1) comprises condenser microphone transistor amplifier BC548 (T1) followed by an opamp stage built around A741 (IC1). The gain of the op-amp can be controlled with the help of 1-mega-ohm potmeter VR1. The AF output from IC1 is coupled to the base of transistor BD139 (T2), which, in turn, modulates the laser beam. The transmitter uses 9V power supply. However, the 3-volt laser torch (after removal of its battery) can be directly connected to the circuitwith the body of the torch connected to the emitter of BD139 and the spring-loaded lead protruding from inside the torch to circuit ground. The receiver circuit (Fig. 2) uses an npn phototransistor as the light sensor that is followed by a two-stage transistor preamplifier and LM386-based audio power amplifier. The receiver does not need any complicated alignment. Just keep the phototransistor oriented towards the remote transmitters laser point and adjust the volume control for a clear sound. To avoid 50Hz hum noise in the speaker, keep the phototransistor away
from AC light sources such as bulbs. The reflected sunlight, however, does not
cause any problem. But the sensor should not directly face the sun.
JANUARY 2002
ELECTRONICS FOR YOU
CIRCUIT IDEAS
MOBILE PHONE BATTERY CHARGER

T.K. HAREENDRAN
I THE SAN
obile phone chargers available in the market are quite expensive. The circuit presented here comes as a low-cost alternative to charge mobile telephones/battery packs with a rating of
7.2 volts, such as Nokia 6110/6150. The 220-240V AC mains supply is downconverted to 9V AC by transformer X1. The transformer output is rectified by diodes D1 through D4 wired in bridge
configuration and the positive DC supply is directly connected to the chargers output contact, while the negative terminal is connected through current limiting resistor R2. LED2 works as a power indicator with resistor R1 serving as the current limiter and LED3 indicates the charging status. During the charging period, about 3 volts drop occurs across resistor R2, which turns on LED3 through resistor R3. An external DC supply source (for instance, from a vehicle battery) can also be used to energise the charger, where resistor R4, after polarity protection diode D5, limits the input current to a safe value. The 3-terminal positive voltage regulator LM7806 (IC1) provides a constant voltage output of 7.8V DC since LED1 connected between the common terminal (pin 2) and ground rail of IC1 raises the output voltage to 7.8V DC. LED1 also serves as a power indicator for the external DC supply. After constructing the circuit on a veroboard, enclose it in a suitable cabinet. A small heat sink is recommended for IC1.
ELECTRONICS FOR YOU
JANUARY 2002
CIRCUIT IDEAS
KNOCK ALARM
PRADEEP G.
SUN
IL KU
MAR
his circuit (Fig. 1), used in conjunction with a thin piezoelectric plate, senses the vibration generated on knocking a surface (such as a door or a table) to activate the alarm. It uses readilyavailable, low-cost components and can also be used to safeguard motor vehicles. The piezoelectric plate is used as the sensor. It is the same as used in ordinary
circuit. When someone knocks on the door, the piezoelectric sensor generates an electrical signal, which is amplified by transistors T1 through T3. The amplified signal is rectified and filtered to produce a low-level DC voltage, which is further amplified by the remaining transistors. The final output from the collector of pnp transistor T6 is applied to reset pin 4 of 555 (IC1) that is wired as an Fig. 2: Proposed installation of knock alarm
Fig. 1: The circuit of knock alarm
piezobuzzers and is easily available in the market. The piezoelectric plate can convert any mechanical vibration into electrical variation. As it doesnt sense sound from a distance like a microphone, it avoids false triggering. The plate can be fixed on a door, cash box, cupboard, etc using adhesive. A 11.5m long, shielded wire is connected between the sensor plate and the input of the
astable multivibrator. Whenever the collector of transistor T6 goes high, the astable multivibrator activates to sound an alarm through the speaker. The value of resistor R12 is chosen between 220 and 680 ohms such that IC1 remains inactive in the absence of any perceptible knock. When the circuit receives an input signal due to knocking, the alarm gets activated for about 10 seconds. This is the
time that capacitor C5 connected between the emitter of transistor T4 and ground takes to discharge after a knock. The time delay can be changed by changing the value of capacitor C5. After about 10 seconds, the alarm is automatically reset. The circuit operates off a 9V or a 12V battery eliminator. The proposed installation of the knock alarm is shown in Fig. 2. This circuit costs around Rs 75.
ELECTRONICS FOR YOU
NOVEMBER 2002
CIRCUIT IDEAS
DING-DONG BELL
PRAVEEN SHANKER
EO I TH SAN
his simple and cost-effective door bell circuit is based on IC 8021-2 from Formox Semiconductors
(Website address: fortech@mantramail. com). It is an 8-pin DIP IC whose only four pins, as shown in the circuit, have been used. The IC has an in-built circuitry to produce dingdong sound each time its pin 3 is pulled low. The sound is stored in the IC as bits, as in a ROM. The sound output from the IC cant however drive a speaker directly, as this puts strain on the device. Therefore a complemen-
tary-pair, two-transistor amplifier is used to amplify the sound to a fair level of audiblity. You may either use a piezo tweeter or an 8-ohm, 500mW speaker at the output. During the standby period, the IC consumes nominal current of a few microamperes only. Therefore switch S1 may be kept closed. Each time switch S2 is pressed, ding dong sound is produced twice. If you try to press switch S2 a second time when the first ding dong sound is still being produed, it has no effect whatever and the two ding-dong bell sounds will be invariably produced. The circuit costs no more than Rs 35 and the IC 8021-2 used in the circuit is readily available for around Rs 15 in the market.
ELECTRONICS FOR YOU
MARCH 2002
C RR CU T II T D EI AD S EAS CI I CI U
PC-BASED OSCILLOSCOPE
M.M. VIJAI ANAND
SAN
I THE
his circuit conditions different signals of frequency below 1 kHz and displays their waveforms on the PCs screen. The hardware is used to condition the input waveform and convert it to the digital format for interfacing to the PC. The software for acquiring the data into the PC and displaying the same on its screen is written in Turbo C. The input waveform (limited to 5V peak-to-peak) is first applied to a full-wave rectifier comprising op-amps A1 and A2 of quad op-amp LM324 (IC4) and a zerocrossing detector built around LM3914 dot/ bar display driver (IC8) simultaneously. The full-wave rectifier rectifies the in-
put signal such that the negative half cycle of the input signal is available in the positive side itself, so both the half cycles are read as positive when it is given as input to the ADC. During positive half cycle, diode D3 is on and diode D4 is off, and op-amps A1 and A2 act as inverters. Thus the output is a replica of the input. During the negative half cycle, diode D3 is off and diode D4 is on. With R2=R3=R4=R5=R6=R=330 ohms, the voltage (V) at inverting pin 2 of op-amp A1 is related to the input voltage (Vi) as follows: Vi/R +V/(2R)+V/R=0 V= -(2/3)Vi
The final output voltage (Vo) at pin 7 of op-amp A2 is given by the following relationship: Vo=(1+R/2R)(-2Vi/3)= -Vi As Vi is negative, the output voltage is positive. The zero-crossing detector detects whether the cycle is positive or negative. It is the most critical part of the circuit and if it operates improperly, the symmetry of the analogue signal displayed in the PC monitor gets affected. At the zero-crossing instant when the input signal transits to negative side, the zero-crossing detector informs the PC by taking pin 15 of 25pin D connector of the parallel port high.
ELECTRONICS FOR YOU
DECEMBER 2002
CIRCUIT IDEAS
The input at pin 15 of D connector goes low when the input signal transits to positive side. The zero-crossing detector communicates with the PC through bit D3 of the status port 379Hex. The zero-crossing detector has been realised using LM3914 IC. You may adjust VR1 such that the last LED (LED10) goes off when the input signal transits negative side of the input waveform. The LM3914 itself rectifies the input signal and allows only positive half of the cycle. The output from the full-wave rectifier is applied to the input of a sample-and-hold circuit comprising op-amps A3 and A4 of the LM324 (IC5), capacitor C3, transistor T1 (SL100), and analogue switch IC6 (CD4016). This circuit samples the input signal, i.e. it divides the waveform into a number of voltages or points and inputs each voltage level (with a delay) to the ADC for conversion into the digital format. Op-amps A3 and A4, along with a switch from IC CD4016 and a 1500pF capacitor with sampling time of 20 s, are used as voltage followers/buffers. When the base of transistor T1 is made low via strobe pin 1 (bit Do of I/O port 37A) of 25-pin D connector of the parallel port, the transistor stops conducting and the voltage at its collector goes high. The high voltage at the collector of transistor T1 closes the switch inside CD4016. As a consequence, the analogue input signal is applied to the capacitor, which charges towards the signal voltage. When the switch is subsequently opened by applying a logic-high voltage from pin 1 of D connector to the base of transistor T1, the capacitor retains the voltage with a loss of about 20 mV/sec and this voltage is given to input pin 6 of the ADC0804 (IC3) via buffer A4 for conversion to the digital format. When the number of sampling points in the input signal waveform is increased, the reconstructed waveform becomes more accurate. The ADC0804 is compatible with microprocessors. It is a 20-pin IC that works with 5V supply. It converts the analogue input voltage to 8-bit digital output. The data bus is tristate buffered. With eight bits, the resolution is 5V/255 = 19.6 mV. The inbuilt clock generator circuit produces a frequency of about 640 kHz with R1=10 kilo-ohms and C4=150 pF, which are the externally connected timing components. The conversion time obtained is approximately 100 s. The functions of other pins are given below: Printer Pin 1 (CS): This is activeLPT1 low chip-select pin. LPT2 Pin 2 (RD): This active-low LPT3 pin enables the digital output buffers. When high, the 8-bit bus will be in Hi-Z state. Pin 3 (WR): This active-low pin is used to start the conversion. Pin 9 (Vref/2): This is optional input pin. It is used only when the input signal range is small. When pin 9 is at 2V, the range is 0-4V, i.e. twice the voltage at pin 9. Pin 6 (V+), Pin 7(V-): The actual input is the difference in voltages applied to these pins. The analogue input can range from 0 to 5V. In this circuit, pins 1 and 2 are always made low, so the IC and the buses are always enabled. Pin 9 is made open, as we use analogue input with 0-5V range. Pin 7 is grounded. Pin 5 (INTR): This active-low pin indicates the end of conversion. It is connected to pin 17 (bit D3 of I/O port 37A) of D connector. (Note that this bit is inverted.) The start-of-conversion command via pin 16 of D connector is applied to pin 3 of the ADC0804. Since we cannot read 8bit digital data output from ADC through the 4-bit status port at a time, we divide it in two 4-bit parts and read. Hence the ADC data output is multiplexed through two 4-bit sections of octal buffers of IC1 (74244) with the help of output-enable signals from pins 2 and 9 of D connector to pins 1 and 19 (OE1 and OE2, respectively) of IC1. The digital data output from IC1 is interfaced to the PC via pins 13 (D4), 12 (D5), 10 (D6), and 11 (D7) of status input port 379H of D connector. The circuit uses 9V and 5V regulated DC supply voltages as shown in the circuit diagram. A PC printer port is an inexpensive platform for implementing low-frequency data acquisition projects. Each printer port consists of data, status, and control port addresses. These addresses are in sequential order; for example, if the data port address is 0x0378, the corresponding status port address is 0x0379 and the control port address is 0x037a. The port addresses for parallel ports are summarised below:
Data port 0x0378 0x0278 0x03bc Status port 0x0379 0x0279 0x03bd Control port 0x037a 0x027a 0x03be
(EFY Lab note. For details of the parallel port pins, refer PC-based Dial Clock with Timer project published in June 2002 issue of EFY.) The software, written in C programming language, is user-friendly and easyto-understand. It gets data from the developed hardware circuit and displays it in the graphical screen with some changes. The C program includes two user-defined functions with the main function: graphics( ) and settings( ). The settings( ) function is used to adjust the voltage and time scale. The graphics( ) function is used to display the waveform on the screen. The sample control signal is used to close the switch in the sample-and-hold circuit, so the capacitor charges towards the analogue input voltage. After the sampling is over, the switch is opened using the same signal. Then the start-of-conversion control signal is given to start the conversion. The sampling time is approximately 20 s and the conversion time is approximately 100 s. After the conversion is over, the 8-bit binary data for the specific voltage sample is available in the data bus of the ADC. Since the PC accepts only 4-bit data through the status port (379H), the 8-bit data must be split into two 4-bit data, which are accepted one after another. This is done by IC 74244, which is controlled by D0 and D7 bits of the data port. Then the two 4-bit data are packed to get the final 8-bit data. The default BGI directory path is set as c:\tc\bgi. The sampling time is decided by the for loop that uses the samp value. The maximum delay produced should be greater than 20 s, which is the maximum acquisition time of the capacitor. When the sample value is increased, the number of points on the input signal decreases and therefore the accuracy decreases. The time scale may be calibrated with 50Hz sine wave as reference. This circuit costs around Rs 400.
PROGRAM IN C FOR PC OSCILLOSCOPE

/* PROGRAM FOR PC OSCILLOSCOPE */ /*by M.M.VIJAI ANAND B.E (E.E.E) C.I.T */ #include<dos.h> #include<time.h> #include<stdio.h> #include <graphics.h> #include<string.h> #include<stdlib.h> #define data 0x0378 #define stat 0x0379 #define cont 0x037a
DECEMBER 2002
ELECTRONICS FOR YOU
CIRCUIT IDEAS
void graphics(int[],int[]); //FUNCTION TO DISPLAY GRAPH AND WAVEFORM void settings(); //FUNCTION TO CHANGE THE SETTINGS(TIME AND VOLTAGE) long int samp=7000; //PLEASE CHECK THESE VALUES WHEN CONVERSION IS // NOT PROPER(+3000) float scale=1; float times=1; char again=a; int number=800; void main() { int i,j,k,a[1700],b[1700],c[1700],e[1700]; //This value 1700 is given when we want to compress the waveform //done when we compress the time scale long int b1; clrscr(); settings(); while(again==a) { for(i=0;i<number;i++) { outportb(cont,0x05^0x0b); outportb(cont,0x04^0x0b); e[i]=(inportb(stat)^0x80)&0x08; for(b1=0;b1<=samp;b1++) //sampling time is approximately 50 sec {} outportb(cont,0x05^0x0b); outportb(cont,0x01^0x0b); outportb(cont,0x05^0x0b); while((inportb(cont)&0x08)==0x00) //converstion time is approximately 100 sec { } outportb(data,0xf0); a[i]=(inportb(stat)^0x80)&0xf0; outportb(data,0x01); b[i]=(inportb(stat)^0x80)&0xf0; outportb(data,0xff); } for(i=0;i<number;i++) { a[i]=a[i]>>4; c[i]=a[i]+b[i]; c[i]=c[i]*0.0196*45/scale; } graphics(c,e); } } void graphics(int a1[],int e1[]) { int gd=DETECT,gm,max,may,a,b,c,im,error,get=5; char str[10],*st=-,d; clrscr(); initgraph(&gd,&gm,c:\\tc\\bgi); //use default bgi path error=graphresult(); if(error != grOk) { printf(Graphics error %s /n,grapherrormsg(error)); //reports error when //graphics is not set printf(PRESS ANY KEY TO EXIT); getch(); exit(1); } setbkcolor(LIGHTCYAN); setcolor(MAGENTA); settextstyle(0,0,2); max=getmaxx(); may=getmaxy(); may=may-20; outtextxy(0,may,OSCILLOSCOPE); settextstyle(0,0,1); setcolor(BLUE); outtextxy(max-200,may+2,press a for next sample); setcolor(BROWN); outtextxy(max-200,may+10,press any key to exit); setcolor(GREEN); settextstyle(0,0,0); for(a=0;a<=may;a+=get) {line(0,a,800,a); } for(a=0;a<=max;a+=get) { line(a,0,a,may); } setcolor(BROWN); setlinestyle(0,3,0); line(max/2,0,max/2,may); line(0,may/2,max,may/2); setcolor(RED); for(a=0,c=0;a<=max;a+=50,c++) { putpixel(a,may/2,BLUE); itoa((a-c*30)*times/2,str,10); outtextxy(a+3,may/2+3,str); } for(b=(may/2)-45,c=1;b>=0;b-=45,c++) { itoa((c*scale),str,10); putpixel((max/2),b,BLUE); outtextxy((max/2)+3,b+3,str); } for(b=(may/2)+45,c=1;b<=800;b+=45,c++) { itoa((c*scale),str,10); strcat(st,str); putpixel((max/2),b,BLUE); outtextxy((max/2)+2,b+2,st); strcpy(st,-); } setcolor(MAGENTA); outtextxy(max-80,may/2+30,time(msec)); settextstyle(0,1,0); outtextxy((max/2)-10,0,volt(s)); setlinestyle(0,0,0); setcolor(RED); moveto(0,may/2); for(b=0,c=0;b<=number;c+=1, b++) { if(e1[b]!=0x08) { lineto(c*times,((may/2)-a1[b])); } else { lineto(c*times,((may/2)+a1[b])); } } again = getch(); closegraph(); restorecrtmode(); } void settings() { int gd=DETECT,gm,error,max,may,b; char c,d,e[2],m,*n; times=1; initgraph(&gd,&gm,c:\\tc\\bgi); //default bgi directory path error=graphresult(); if(error != grOk) { printf(Graphics error %s /n,grapherrormsg(error)); printf(PRESS ANY KEY TO EXIT); getch(); exit(1); } max=getmaxx(); setbkcolor(LIGHTBLUE); settextstyle(1,0,0); setcolor(BROWN); outtextxy(max/2-60,20,SETTINGS); line(0,60,800,60); setcolor(MAGENTA); settextstyle(1,0,1); outtextxy((max/4)-70,80,Voltage Scale); settextstyle(0,0,0); setcolor(BROWN); outtextxy(10,120,DEFAULT :); outtextxy(10,120, 1 unit = 1 volt); setcolor(RED); outtextxy(10,170,TYPE C TO CHANGE AND D TO DEFAULT); c=getch(); if(c==c) { outtextxy(10,200,TYPE 1 for 1 unit = 2 volt); outtextxy(10,240,TYPE 2 for 1 unit = 4 volt); outtextxy(10,300,TYPE 3 for user defined); switch(getch()) { case 1 : { scale=2; break; } case 2 : {scale = 4; break; } case 3 : { outtextxy(10,340,TYPE VALUES FROM 1 TO 9 (minimize) or m to (magnify)); d=getch(); if(d==m) { outtextxy(10,360,TYPE a (1 unit = 0.5 volt) or b (1 unit = 0.25 volt)); switch(getch()) { case a: { scale=0.5; break; } case b: { scale=0.25; break; } } } else { e[0]=0'; e[1]= 0; e[2]=d; scale=atoi(e); break; } } } } setcolor(BROWN); outtextxy(10,380,TYPE C TO CHANGE TIME SETTINGS); m=getch(); if( m==c) { cleardevice(); outtextxy(10,20,X AXIS 1 unit= 10msec CHANGE TO x(10msec)); outtextxy(10,40,TYPE a IF x IS (2 to 9) ,b IF x IS (10 to 99) AND c IF x IS (.5 TO .9)); switch(getch()) { case a: outtextxy(10,60,x value is ....); n[0]=getch(); times=atoi(n); itoa(times,n,10); outtextxy(10,70,n); break; case b: outtextxy(10,60,x value is ....); n[0]=getch(); n[1]=getch(); times=atoi(n); itoa(times,n,10); outtextxy(10,70,n); break; case c: outtextxy(10,60,x value is...); getch(); n[0]=getch(); times=atoi(n)*0.1; outtextxy(10,70,scale decremented); break; } number=800; if(times<1) {number=number/times; } getch(); } closegraph(); restorecrtmode(); }
ELECTRONICS FOR YOU
DECEMBER 2002
CIRCUIT
IDEAS
9-LINE TELEPHONE SHARER

DHURJATI SINHA
his circuit is able to handle nine independent telephones (using a single telephone line pair) located at nine different locations, say, up to a distance of 100m from each other, for receiving and making outgoing calls, while maintaining conversation secrecy. This circuit is useful when a single telephone line is to be shared by more members residing in different rooms/apartments. Normally, if one connects nine phones in parallel, ring signals are
S.C.
EDI DWIV
heard in all the nine telephones (it is also possible that the phones will not work due to higher load), and out of nine persons eight will find that the call is not for them. Further, one can overhear others conversation, which is not desirable. To overcome these problems, the circuit given here proves beneficial, as the ring is heard only in the desired extension, say, extension number 1. For making use of this facility, the calling subscriber is required to initially dial the normal phone number of the
called subscriber. When the call is established, no ring-back tone is heard by the calling party. The calling subscriber has then to press the asterik (*) button on the telephone to activate the tone mode (if the phone normally works in dial mode) and dial extension number, say, 1, within 10 seconds. (In case the calling subscriber fails to dial the required extension number within 10 seconds, the line will be disconnected automatically.) Also, if the dialed extension phone is not lifted within 10 seconds, the ring-back tone will cease. The ring signal on the main phone line is detected by opto-coupler MCT2E (IC1), which in turn activates the 10-second on timer, formed by IC2 (555), and energises relay RL10 (6V, 100ohm, 2 C/O). One of the N/O contacts of the relay has been used to connect +6V rail to the processing circuitry and the other has been used to provide 220-ohm loop resistance to deenergise the ringer relay in telephone exchange, to cut off the ring. When the caller dials the extension number (say, 1) in tone mode, tone receiver CM8870 (IC3) outputs code 0001, which is fed to the 4bit BCD-to-10 line decimal decoder IC4 (CD4028). The output of IC4 at its output pin 14 (Q1) goes high and switches on the SCR (TH-1) and associated relay RL1. Relay RL1, in turn, connects, via its N/O contacts, the 50Hz extension ring signal, derived from the 230V AC mains, to the line of telephone 1. This ring signal is available to telephone 1 only, because half of the signal is blocked by diode D1 and DIAC1 (which do not conduct below 35 volts). As soon as phone 1 is lifted, the ring current increases and voltage drop across R28 (220-ohm, 1/2W resistor) increases and operates opto-coupler IC5 (MCT-2E). This in turn resets timer IC2 causing: (a) interruption of the power supply for processing circuitry as well as the ring
CIRCUIT IDEAS
SOLIDSTATE SWITCH FOR DC-OPERATED GADGETS

PRAVEEN SHANKER
EDI DWIV . C . S
his solidstate DC switch can be assembled using just three transistors and some passive components. It can be used to switch on one gadget while switching off the second gadget with momentary operation of switch. To reverse the operation, you just have to momentarily depress another switch. The circuit operates over 6V-15V DC supply voltage. It uses positive feedback
from transistor T2 to transistor T1 to keep this transistor pair in latched state (on/ off), while the state of the third transistor stage is the complement of transistor T2s conduction state. Initially when switch S3 is closed, both transistors T1 and T2 are off, as no forward bias is available to these, while the base of transistor T3 is effectively grounded via resistors R8 and R6 (shunted by the load of the first gadget). As a result, transistor T3 is forward biased and gadget 2 gets the supply. This is indicated by glowing of LED2. When switch S1 is momentarily depressed, T1 gets the base drive and it grounds the base of transistor T2 via resistor R4.
Hence transistor T2 (pnp) also conducts. The positive voltage available at the collector of transistor T2 is fed back to the base of transistor T1 via resistor R3. Hence a latch is formed and transistor T2 (as also transistor T1) continues to conduct, which activates gadget 1 and LED1 glows. Conduction of transistor T2 causes its collector to be pulled towards positive rail. Since the collector of T2 is connected to the base of pnp transistor T3, it causes transistor T3 to cut off, switching off the supply to gadget 2) as well as extinguishing LED2. This status is maintained until switch S2 is momentarily pressed. Depression of switch S2 effectively grounds the base of transistor T1, which cuts off and thus virtually opens the base-emitter circuit of transistor T2 and thus cutting it off. This is the same condition as was obtained initially. This condition can be reversed by momentarily pressing switch S1 as explained earlier. EFY lab note. During testing, it was noticed that for proper operation of the circuit, gadget 1 must draw a current of more than 100 mA (i.e. the resistance of gadget 1 must be less than 220 ohms) to sustain the latched on state. But this stipulation is not applicable for gadget 2. A maximum current of 275 mA could be drawn by any gadget. The total cost of this circuit is around Rs 30.
APRIL 2002
ELECTRONICS FOR YOU
CIRCUIT IDEAS
ELECTRONIC SECURITY SYSTEM

K. BHARATHAN
I VED DWI . C . S
his reliable and easy-to-operate electronic security system can be used in banks, factories, commercial establishments, houses, etc. The system comprises a monitoring system and several sensing zones. Each sensing zone is provided with a closed-loop switch known as sense switch. Sense switches are fixed on the doors of premises under security and connected to the monitoring system. As long as the doors are closed, sense switches are also closed. The monitoring system can be installed at a convenient central place for easy operation. Fig. 1 shows the monitoring circuit only for zone 1 along with the common alarm circuit. For other zones, the monitoring circuit is identical, with only the prefixes of components changing as per zone number. Encircled points A, B, and C of each zone monitoring circuit need to be joined to the corresponding points of the alarm circuit (upper half of Fig. 1). When zone 1 sensing switch S11, zone on/off slide switch S12, and system on/off switch S1 are all on, pnp transistor T12 reverse biases to go in cut-off condition, with its collector at around 0 volt. When the door fitted with sensor switch S11 is opened, transistor T12 gets forward biased and it conducts. Its collector voltage goes high, which forward biases transistor T10 via resistor R10 to turn it on. (Capacitor C10 serves as a filter capacitor.) As a result, the collector voltage of transistor T10 falls to forward bias transistor T11, which conducts and its collector voltage is sustained at a high level. Under this latched condition, sensor switch S11 and the state of transistor T12 have no effect. In this state, red LED11 of the zone remains lit. Simultaneously, the high-level voltage from the collector of transistor T11 via diode D10 is applied to VDD pin 5 of siren sound generator IC1 (UM3561) whose pin 2 is grounded. Resistor R3 connected across pins 7 and 8 of IC1 determines the frequency of the in-built oscillator. As a result, IC1 starts generating the audio signal output at pin 3. The output voltage from IC1 is further amplified by Darlington pair of transistors T1 and T2. The amplified
output of t h e Darlington pair drives the loudspeaker whose output volume can be controlled by potentiometer VR1. Capacitor C1 serves as a filter capacitor. Y o u can alter the alarm sound as desired by changing the connections of IC1 as shown in the table. T h e circuit continues to sound the alarm until zone door Fig. 1: Monitoring circuit along with the alarm circuit
Fig. 2: Physical layout of sensors and monitoring/alarm system
is closed (to close switch S11) and the reset switch is pressed momentarily (which causes transistor T10 to cut off, returning the circuit to its initial state).
The system operates off a 3V DC battery or recharging battery with charging circuit or battery eliminator. If desired, more operating zones can be added.
MARCH 2003 ELECTRONICS FOR YOU
CIRCUIT IDEAS
Alarm sound Circuit connections IC pin 1 connected to IC pin 6 connected to
Police siren Ambulance siren Fire engine Sound Machinegun sound
Note. NC indicates no connection
NC NC NC VSS
NC VDD VSS NC
for respective zones in closed position. Also keep zone slide switches S12, S22, S32, S42, etc in on position. This puts the system in operation, guarding all the zone
Initially keep the monitoring system switch S1 off. Keep all the zone doors fixed with sensing switches S11, S21, S31, S41, etc closed. This keeps the sensing switches
doors. Now, if the door of a particular zone is opened, the monitoring system sounds an audible alarm and the LED correspond-
ing to the zone glows to indicate that the door of the zone is open. The alarm and the LED indication will continue even after that particular door with the sensing switch is immediately closed, or even if that switch is removed/damaged or connecting wire is cut open. Any particular zone in the monitoring system can be put to operation or out of operation by switching on or switching off the corresponding slide switch in the monitoring system. The circuit for monitoring four zones costs around Rs 400.
ELECTRONICS FOR YOU
MARCH 2003
CIRCUIT
IDEAS
HOUSE SECURITY SYSTEM

MALAY BANERJEE
MAR IL KU SUN
nected at the output. The receiver unit comprises two identical step-down transformers (X1 and X2), two 6V relays (RL1 and RL2), an LDR, a transistor, and a few other passive com-
ere is a low-cost, invisible laser circuit to protect your house from thieves or trespassers. A laser pointer torch, which is easily available in the market, can be used to operate this device. The block diagram of the unit shown in Fig. 1 depicts the overall arrangement for providing security to a house. A laser torch powered by 3V power-supply is used
for generating a laser beam. A combination of plain mirrors M1 through M6 is used to direct the laser beam around the house to form a net. The laser beam is directed to finally fall on an LDR that forms part of the receiver unit as shown in Fig. 2. Any interruption of the beam by a thief/ trespasser will result into energisation of the alarm. The 3V power-supply circuit is a conventional fullwave rectifier-filter circuit. Any alarm unit that operates on 230V AC can be con-
ponents. When switches S1 and S2 are activated, transformer X1, followed by a full-wave rectifier and smoothing capacitor C1, drives relay RL1 through the laser switch. The laser beam should be aimed continuously on LDR. As long as the laser beam falls on LDR, transistor T1 remains forward biased and relay RL1 is thus in energised condition. When a person crosses the line of laser beam, relay RL1 turns off and transformer X2 gets energised to provide a parallel path across N/C contact and the pole of relay RL1. In this condition, the laser beam will have no effect on LDR and the alarm will continue to operate as long as switch S2 is on. When the torch is switched on, the pointed laser beam is reflected from a definite point/place on the periphery of the house. Making use of a set of properly oriented mirrors one can form an invisible net of laser rays as shown in the block diagram. The final ray should fall on LDR of the circuit. Note. LDR should be kept in a long pipe to protect it from other sources of light, and its total distance from the source may be kept limited to 500 metres. The total cost of the circuit, including the laser torch, is Rs 400 or less.
CIRCUIT IDEAS
SONG NUMBER DISPLAY

PRABHASH K.P.
SAN
O I THE
eres a circuit to display the song number in an audio system for quick reference to songs. It also serves the purpose of an extra visual indicator in modern audio systems. When the power is switched on, the power-on-reset circuit comprising 3.3k resistor R20 and 1F, 25V capacitor C6 resets the counters, showing 00 in the display. One can also reset the display to zero at any time by pressing reset switch S1. When the first song starts playing, the output pins of IC1 (KA2281) go low and capacitor C5 starts charging. This forward biases transistor T1 and hence the input to IC3 at pin 1 goes to high state. As a result, the output of the counter goes to the next state, showing 01 on the display. The counter remains in this state until the song is completed. During the time gap before the next song starts playing, capacitor C5 discharges. After discharging of capacitor C5, the input to IC3 becomes low again. When the song starts, the process described above is repeated and the display shows 02. You can adjust VR3 to change the time gap setting. This must be set such that the circuit doesnt respond to short gaps, if any, within a song and responds only to long gaps between different songs. Transistor T2 helps in gap-delay adjustment. The intensity of LED11 diminishes when a song is completed and the counter is ready to accept the next pulse. Connect the input to the preamp output or equaliser output of the audio system. Adjust VR1 and VR2 to get the correct audio-level indication. If you are already using KA2281 for audio-level indication, just connect diodes D1 and D2 as shown in this circuit. Note that the counter counts the songs by detecting the gaps. Therefore any long gap within a song may cause false triggering and the display will also be incremented. However, as this is very unlikely to happen, the circuit shows the correct song number almost all the time. The circuit costs around Rs 100.
APRIL 2003
ELECTRONICS FOR YOU
CIRCUIT
IDEAS
SPELLER EFFECT SIGN DISPLAY

VIJAYA KUMAR P.
EDI DWIV S.C.
he circuit described here uses lowcost and easily available IC CD4017 to produce a speller type light display. In such displays, each letter of the sign sequentially lights up, one after the other, until all letters are glowing. After a few seconds, the letters switch off and the cycle repeats. This circuit provides a maximum of nine channels and therefore can be used to spell a word or sign having up to nine characters. Timer IC1 (555) is configured in
CD4017 is a decade counter having ten outputs, of which one output is high for each clock pulse. However, this produces running lights effect. To change this sequence to get the speller effect, pnp transistors T1 through T9 are wired as shown in the figure. Nine triacs (triac 1 through triac 9) are used to drive 230V bulbs. (In place of 230V bulbs, miniature lamps connected in series in the form of characters or letters can also be used, provided the voltage drop across the series
high, transistor T1 goes off and its output at the collector goes low. Since the emitter of transistor T2 is connected to the collector of transistor T1, and collector and emitter terminals of transistors T1 through T9 are connected in series, all transistors next to transistor T1, i.e. transistors T2 through T9, do not get supply and hence all their outputs go low. Next, when Q1 output goes high, transistor T2 goes off. Thus outputs of transistors T2 through T9 remain low. Since Q0 output at this instant is low, transistor T1 is forward biased and its output goes high to light up the first character. Similarly, when Q2 output goes high, Q0 and Q1 outputs are low and therefore outputs of transistors T1 and T2 go high to light up the first and second characters. This process continues until all transistors turn on, making all the characters
astable mode to produce clock signal for triggering IC2 (CD4017). Speed of switching on the display can be controlled by varying preset VR1.
combination is 230 volts.) When any of the outputs of IC2 goes high, the corresponding transistor connected to the output goes off. When Q0 is
to light up. The cycle repeats endlessly, producing the speller type light effect.
ELECTRONICS FOR YOU NOVEMBER 2001
CIRCUIT
IDEAS
STEREO TAPE HEAD PREAMPLIFIER FOR PC SOUND CARD

MAR IL KU N U S
T.K. HAREENDRAN
ere is a stereo tape head preamplifier circuit for your PC sound card that can playback your favourite audio cassette through the PC. Audio signals from this circuit can be di-
The amplified and equalised signals available at output pins 3 and 6 of IC1 are coupled to the inputs of line amplifier circuit built around transistors T1 (via capacitor C5, potmeter VR1, resistor R8, and
other audio device as well. When the preamplifier is in off state, switching relay RL1 is off and it allows connection of external signals to the sound card. When the preamplifier is turned on, the relay is energised by transistor T3 after a short delay determined by the values of resistor R21 and capacitor C23. On energisation, the relay contacts changeover the signals to internal source, i.e. the head preamplifier. After constructing the whole circuit on a veroboard, enclose it in a mini metallic cabinet with level controls and sock-
rectly connected to the stereo-input (lineinput) socket of the PC sound card for further processing. The circuit is built around a popular stereo head preamp IC LA3161. Weak electrical signals from the playback heads are fed to pins 1 and 8 of IC1 via DC decoupling capacitors C1 and C6, respectively. Components between pins 2 and 3 and pins 6 and 7 provide adequate equalisation to the signals for a normal tape playback.
capacitor C12) and T2 (via capacitor C10, potmeter VR2, resistor R19, and capacitor C16), respectively. Left and right playback levels can be adjusted by variable resistors VR1 and VR2. The audio signals are finally available at the negative ends of capacitors C13 and C17. The circuit wired around relay driver transistor T3 serves as a simple source selector. This is added deliberately to help the user share the common PC sound card line-input terminal for operating some
ets at suitable points. Use a regulated 1A, 12V DC power supply for powering the whole circuit including the tape deck mechanism. (A 1A, 18V AC secondary transformer with 4700F, 40V electrolytic capacitor and 78M12 regulator is sufficient.) You can use any kind of tape deck mechanism with this circuit. Use of goodquality playback head and well-screened wires are recommended.
ELECTRONICS FOR YOU OCTOBER 2001
CIRCUIT IDEAS
LEAD-ACID BATTERY CHARGER WITH VOLTAGE ANALYSER

D. MOHAN KUMAR
SAN
I THE
owadays maintenance-free lead-acid batteries are common in vehicles, inverters, and UPS systems. If the battery is left in a poor state of charge, its useful life is shortened. It also reduces the capacity and rechargeability of the battery. For older types of batteries, a hygrometer can be used to check the specific gravity of the acid, which, in turn, indicates the charge condition of the battery. However, you cannot use a hygrometer for sealedtype maintenance-free batteries. The only way to know their charge level is by checking their terminal voltage. The circuit presented here can replenish the charge in a battery within 6-8 hours. It also has a voltage analysing circuit for quick checking of voltage before start of charging, since overcharging may damage the battery. The voltage analyser gives an audio-visual indication of the battery voltage level and also warns about the critical voltage level at which the battery requires immediate charging.
The charger circuit consists of a standard step-down 12V AC (2-amp) transformer and a bridge rectifier comprising diodes D1 through D4. Capacitor C1 smoothes the AC ripples to provide a clean DC for charging the battery. The battery voltage analyser circuit is built around the popular quad op-amp LM324 that has four separate op-amps (A through D) with differential inputs. Opamps have been used here as comparators. Switch S2 is a pushswitch, which is pressed momentarily to check the battery voltage level before charging the battery. The non-inverting terminals of op-amps A through D are connected to the positive supply rail via a potential divider chain Battery voltage Red
<9.8V >9.8V 11.5V 12.0V 12.5V Off On On On On
comprising resistors R1 through R5. Thus the voltage applied to any non-inverting input is the ratio of the resistance between that non-inverting terminal and ground to the total resistance (R1+R2+R3+R4+R5). The resistor chain provides a positive voltage of above 5V to the non-inverting inputs of all op-amps when battery voltage is 12.5V or more. A reference voltage of 5V is applied to the inverting inputs of op-amps via 5V zener diode ZD1. When the circuit is connected to the battery and pushswitch S2 is pressed (with S1 open), the battery voltage is sampled by the analyser circuit. If the supply voltage sample applied to the non-inverting input of an op-amp exceeds the reference voltage applied Status of LEDs Comments to the inverting inputs, the Green Yellow Orange output of the Off Off Off Buzzer off op-amp goes Off Off Off Danger level high and the On Off Off Low level LED connected On On Off Normal level at its output On On On High level lights up.
ELECTRONICS FOR YOU
MARCH 2003
CIRCUIT IDEAS
The different levels of battery voltages are indicated by LED1 through LED4. All the LEDs remain lit when the battery is fully charged (above 12.5V). The buzzer connected to the output of IC1 also sounds (when S2 is pressed with S1 kept open) as long as the voltage of battery is above 9.8V. If the voltage level goes below 9.8V, the buzzer goes off, which indicates that its time to replace the battery. The status of LEDs for different battery voltages is shown in the table. The circuit can be assembled on a general-purpose PCB or a veroboard. Use 4mm wire and crocodile clips to connect the charger to the battery. A 2.5-amp fuse connected to the output of the charger protects the analyser circuit against accidental polarity reversal. The circuit costs around Rs 120 with all accessories.
MARCH 2003
ELECTRONICS FOR YOU
CIRCUIT IDEAS
THREE-COLOUR DISPLAY USING BICOLOUR LEDs

PRIYANK MUDGAL
I VED DWI S.C.
he circuit presented here uses bicolour LEDs to generate a display in three colours, namely, red, green, and yellowish green. Transistors T1 through T20 form a grid to which common-cathode bicolour LEDs (LED1 through LED10) are connected. Transistors T1 through T10 have their collector terminals connected to the emitter of transistor T21. Similarly, transistors T11 through T20 have their collector terminals connected to the emitter of transistor T22. The bases of each pair of transistors (i.e. T1 and T11, T2 and T12,, T10 and T20) are tied to outputs Q0, Q1,, Q9, respectively, of IC1 (CD4017) through 10-kiloohm resistors as shown in the figure. Positive supply to collectors of transistors T1 through T10 is controlled by transistor T21. Similarly, positive supply to collectors of transistors T11 through T20 is controlled by transistor T22. IC1 and IC2 are decade counters. Clock pulse to IC1 is provided by the oscillator circuit comprising NOR gates N1 and N2. The outputs of IC1 advance sequentially with each clock. (Any other source of squarewave pulses also serves the purpose.) IC2 is used to select the mode of display. Clock input pin 14 of IC2 is connected to Q9 output of IC1. Thus IC2 receives one pulse after every ten pulses received by IC1. When the circuit is switched on, Q0 output of IC2 is active high. Thus transistor T21 gets forward biased via diode D3 and it conducts to extend positive supply to transistors T1 through T10. Transistors T1 through T10 are forward biased sequentially by Q0 through Q9 outputs of IC1, i.e. at a time only one of these ten transistors is forward biased (on). Thus only red LED parts of bicolour LEDs light up sequentially. (Transistor T22 is not conducting at this moment.) When red LED part of LED10 glows, IC2 receives a clock pulse and its Q1 output goes high. Transistor T21 still conducts, as it is forward biased through diode D6, and next again via diode D5. Thus red LEDs complete two more glowing sequences.
After completion of the third glowing sequence of red LEDs, when Q3 output of IC2 goes high, transistor T21 stops conducting and T22 starts conducting with the next three sequences of green LEDs of bicolour LEDs (LED1 through LED10) glowing sequentially. After completion of three sequences of green LEDs, output Q6 of IC2 goes high.
Now both transistors T21 and T22 conduct due to diodes D1 and D2. Thus both red and green LEDs in bicolour LEDs (LED1 through LED10) glow sequentially. The effect of red and green LEDs glowing together is a distinct yellowish orange colour. This sequence repeats four times. Thereafter, the whole sequence repeats, starting with red LEDs. Thus the bicolour-
CIRCUIT IDEAS
LED display shows three coloursred, green, and yellowish greenone after the other. The speed of display can be controlled by preset VR1. One can omit automatic selection of different colours by omitting IC2 and replacing connections to pins 3, 5, and 7 of IC2 with SPDT switches. (Thus diodes D3-D12 are also omitted.) This circuit costs around Rs 250.
FEBRUARY 2003
ELECTRONICS FOR YOU
CIRCUIT IDEAS
ULTRA-BRIGHT LED LAMP

N.S. HARISANKAR VU3NSH
I VED DWI S.C.
his ultra-bright white LED lamp works on 230V AC with minimal power consumption. It can be used to illuminate VU meters, SWR meters, etc. Ultra-bright LEDs available in the market cost Rs 8 to 15. These LEDs emit a 1000-6000mCd bright white light like welding arc and work on 3 volts, 10 mA. Their maximum voltage is 3.6 volts and the current is 25 mA. Anti-static precautions should be taken when handling the LEDs. The LEDs in water-clear plastic package
Fig. 1: The circuit of ultra-bright white LED lamp
Fig. 2: 16-LED combination
Fig. 3: 46-LED combination
emit spotlight, while diffused type LEDs have a wide-angle radiation pattern. This circuit (Fig. 1) employs capacitive reactance for limiting the current flow through the LEDs on application of mains voltage to the circuit. If we use only a series resistor for limiting the current with mains operation, the limiting resistor itself will dissipate around 2 to 3 watts of power,
whereas no power is dissipated in a capacitor. The value of capacitor is calculated by using the following relationships: XC = 1/(2fC) ohms (a) XC = VRMS /I ohms (b) where XC is capacitive reactance in ohms, C is capacitance in farads, I is the current through the LED in amperes, f is the mains frequency in Hz, and Vrms is the input mains voltage. The 100-ohm, 2W series resistor avoids heavy inrush current during transients. MOV at the input prevents surges or spikes, protecting the circuit. The 390-kilo-ohm, -watt resistor acts as a bleeder to provide discharge path for capacitor Cx when mains supply is disconnected. The zener diode at the output section prevents excess reverse voltage levels appearing across the LEDs during negative half cycles. During positive half cycle, the voltage across LEDs is limited to zener voltage.
Use AC capacitors for Cx. Filter capacitor C1 across the output provides flickerfree light. The circuit can be enclosed in a CFL round case, and thus it can be connected directly to AC bulb holder socket. A series combination of 16 LEDs (Fig. 2) gives a luminance (lux) equivalent of a 12W bulb. But if you have two series combinations of 23 LEDs in parallel (total 46 LEDs as shown in Fig. 3), it gives light equal to a 35W bulb. 15 LEDs are suitable for a tablelamp light. Diode D1 (1N4007) and capacitor C1 act as rectifying and smoothing elements to provide DC voltage to the row of LEDs. For a 16-LED row, use Cx of 0.22 F, 630V; C1 of 22 F, 100V; and zener of 48V, 1W. Similarly, for 23+23 LED combination use Cx of 0.47 mF, 630V; C1 of 33 F, 150V; and zener of 69V, 1W. This circuit (inclusive of LEDs) costs Rs 200 to Rs 400.
FEBRUARY 2003
ELECTRONICS FOR YOU
C RR CU T II T D EI AD S EAS CI I CI U
VERSATILE EMERGENCY LIGHT USING FLUORESCENT TUBES

VIVEK KALKUR M.
I VED DWI S.C.
mergency lights using incandescent bulbs are inherently inefficient compared to those using fluorescent tubes. Heres a versatile emergency light using fluorescent tubes. You can operate it using readymade SUNCA or similar other inverter transformers, which are readily available in the market for around Rs 25. With this circuit you can drive two 6W, 22.8cm (9-inch) fluorescent tubes, with the option to use a single tube or a pair of tubes with the help of DPDT switch S2. Step-down transformer X1, diodes D1D4, capacitor C1, and 5V regulator IC1 (7805) form a regulated power supply. A 2.7V zener (ZD1) in common terminal of the regulator props up the output voltage to 7.7 volts. The regulated voltage is applied to the battery through diodes D6 and D7, which cause a drop of about 1.4V across them. Thus the effective charging voltage is about 6.3V, which prevents overcharging of the battery as the terminal voltage of the battery cannot exceed 6.3V. When AC mains supply is present, the battery starts charging and green LED1 glows to indicate the same. Diode D5 reverse biases transistor T1 forming part of the inverter oscillator and thus the tubes dont glow. When mains supply fails, transistor T1 starts oscillating and supplies power to inverter transformer X2 and the tubes glow.
An on/off switch (S1) is used to switch off the light when it is not required. D882 (actually, 2SD882) is an npn power transistor in TO-126 package. It is mounted on a suitable heat-sink to pre-
vent it from thermal runaway. For good illumination, use Toshibas FL6D fluorescent tubes. The circuit (excluding the cabinet) costs around Rs 350.
ELECTRONICS FOR YOU
MARCH 2003
CIRCUIT IDEAS
CLAP-BASED SWITCHING FOR DEVICES

MANOJ KUMAR SAHA
I VED DWI S.C.
t is quite difficult to find the switch board in a dark room to turn on the light. Heres a clap switch that allows you to switch on lights, fans, and motors sequentially by just clapping in the vicinity of the microphone used in the circuit. The mains supply is stepped down to 15-0-15V AC by step-down transformer X1. The output of the transformer is rectified, filtered, and regulated by diodes D1 through D4, capacitors C1 through C4, and IC1 (regulator IC 7812) and IC2 (regulator IC 7912), respectively. Additional
filtering is performed by capacitors C5 through C8 to get +12V, 0V (Gnd) and 12V DC required for the operation of the circuit. The clap sound impulses are converted into electrical signals by a condenser microphone that forms a Wheatstone bridge together with resistors R4, R5, and R3. The microphone is suitably biased through resistor R3. The output of the microphone is coupled to op-amp IC 741 (IC3) having a voltage gain of 45. The output of IC3, after passing through capacitor C10, is free from any DC component of signal. Capacitors C15 and C17 are used for spike and surge suppression.
Diodes D5 and D6 and capacitor C11 form the detector circuit. Resistor R6 is used here for quick discharge of capacitor C10. The detected clap signal is used to switch on transistor T1. On conduction of transistor T1, its collector voltage falls to trigger timer IC4 connected as a monostable. The combination of resistor R9 and capacitor C12 determine the pulsewidth of the monostable (about one second, with the component values shown). AND gate IC5 (4081) is used as a buffer between the output of IC4 and clock input to decade counter IC6 (CD4017). Thus each clap causes outputs of IC6 to advance in sequential manner and switch on the corresponding devices. If you want a lamp to be switched on when output Q1 goes high (after first clap), then in place of R11 and LED2 use a relay driver circuit at Q1 output similar to that used for Q2 output (for fan). As stated earlier, only one output of CD4017 can be high at any given time. Thus first clap causes LED1 to go off and LED2 to glow. The second clap causes only the fan to switch on via relay RL1. The third clap causes the miniature 12V motor to run. On fourth clap, Q4 output goes high momentarily to reset IC6 since Q4 output is connected to its reset pin 15. In reset state, LED1 connected to Q0 output lights up. The circuit costs around Rs 150.
MARCH 2003 ELECTRONICS FOR YOU

Electronics Projjects1

Uploaded by

Copyright:

Available Formats

Electronics Projjects1

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Electronics Projjects1

Uploaded by

Copyright:

Available Formats

CIRCUIT IDEAS

MULTI-SWITCH DOORBELL WITH INDICATORS

I VED DWI S.C.

Fig. 2: Suggested panel layout of musical doorbell

Fig. 1: Multi-switch doorbell with indicators

ELECTRONICS FOR YOU

SONG NUMBER DISPLAY

ELECTRONICS FOR YOU

I VED DWI S.C.

crease the number of flashes. This circuit costs around Rs 50.

ELECTRONICS FOR YOU

INTRUDER RADIO ALERT SYSTEM

Fig. 2: Circuit diagram of intruder radio alert system

Fig. 1: Block diagram of the intruder radio alert system

ELECTRONICS FOR YOU

AUTOMATED TRAFFIC SIGNAL CONTROLLER

Fig. 1: Flow of traffic in all possible directions

TABLE I Simultaneous States of Signals for All the Traffic

Fig. 2: The circuit diagram for traffic light signalling

ELECTRONICS FOR YOU

INFRARED TOY CAR MOTOR CONTROLLER

ELECTRONICS FOR YOU

ANTI-THEFT SECURITY FOR CAR AUDIOS

EDI DWIV S.C.

ELECTRONICS FOR YOU  JULY 2001

SIMPLE TELEPHONE RING TONE GENERATOR

ELECTRONICS FOR YOU  JULY 2001

DTMF PROXIMITY DETECTOR

ELECTRONICS FOR YOU  JUNE 2001

UNDER-/OVER-VOLTAGE BEEP FOR MANUAL STABILISER

ELECTRONICS FOR YOU  MAY 2001

15-STEP DIGITAL POWER SUPPLY

ELECTRONICS FOR YOU  MAY 2001

GENERATION OF 1-SEC. PULSES SPACED 5-SEC. APART

ELECTRONICS FOR YOU  FEBRUARY 2001

AUTOMATIC HEAT DETECTOR

ELECTRONICS FOR YOU  MARCH 2001

MUSICAL TOUCH BELL

EDI DWIV S.C.

ELECTRONICS FOR YOU  MARCH 2001

PRECISION AMPLIFIER WITH DIGITAL CONTROL

EDI DWIV S.C.

ELECTRONICS FOR YOU  JANUARY 2001

C I R C U I T I D E A S CIR CUIT IDEAS

ADD-ON STEREO CHANNEL SELECTOR

ily extended up to ten, by using additional 4066 ICs.

Telephone Number Display

ELECTRONICS FOR YOU n  MAY '99

LUGGAGE SECURITY SYSTEM

UNIVERSAL HIGH-RESISTANCE VOLTMETER

TABLE I Position 1 of Function Switch

TABLE II Position 2 of Function Switch

TABLE III Position 3 of Function Switch

TABLE IV Position 4 of Function Switch

ELECTRONICS FOR YOU  FEBRUARY 2000

Infrared Cordless Headphone

TV to headphones. Without using any lens, a range of up to 6 metres is

9-volt battery can be used with receiver for portable operation.

ELECTRONICS FOR YOU n  AUGUST '99

ELECTRONICS FOR YOU JULY 2001

ELECTRONICS FOR YOU JULY 2001

ELECTRONICS FOR YOU JUNE 2001

ELECTRONICS FOR YOU MAY 2001

ELECTRONICS FOR YOU MAY 2001

ELECTRONICS FOR YOU FEBRUARY 2001

ELECTRONICS FOR YOU MARCH 2001

ELECTRONICS FOR YOU MARCH 2001

ELECTRONICS FOR YOU JANUARY 2001

ELECTRONICS FOR YOU n MAY '99

ELECTRONICS FOR YOU FEBRUARY 2000

ELECTRONICS FOR YOU n AUGUST '99

ELECTRONICS FOR YOU n AUGUST '99

ELECTRONICS FOR YOU n JULY '99

ELECTRONICS FOR YOU n JUNE '99

ELECTRONICS FOR YOU APRIL 2001

ELECTRONICS FOR YOU APRIL 2001

ELECTRONICS FOR YOU DECEMBER 2001

ELECTRONICS FOR YOU DECEMBER 2001

ELECTRONICS FOR YOU AUGUST 2001

ELECTRONICS FOR YOU FEBRUARY 2001

ELECTRONICS FOR YOU APRIL 2001

ELECTRONICS FOR YOU NOVEMBER 2001

ELECTRONICS FOR YOU OCTOBER 2001