Application Note 13.56 MHZ, Class D Push-Pull, 2Kw RF Generator With Microsemi Drf1300 Power Mosfet Hybrid
Application Note 13.56 MHZ, Class D Push-Pull, 2Kw RF Generator With Microsemi Drf1300 Power Mosfet Hybrid
Application Note 13.56 MHZ, Class D Push-Pull, 2Kw RF Generator With Microsemi Drf1300 Power Mosfet Hybrid
56 MHz, Class D Push-Pull, 2KW RF Generator with Microsemi DRF1300 Power MOSFET Hybrid
Dec. 30 2008
By Gui Choi Sr. RF Application Engineer
The DRF1300/CLASS-D Reference design is available to expedite the evaluation of the DRF1300 push-pull MOSFET hybrid. This application note or the reference design does not represent a finished commercial-ready design. It is only an engineering tool to demonstrate the capability of the DRF1300 under 50 Ohm, flat line conditions. Each reference design has been verified to perform to the specifications of the application note. The application note contains a parts list, board layout and schematic that enables the user to facilitate any repairs resulting beyond its intended use. By purchasing this reference design the user takes full responsibility for repair and any modifications. No warranties, repairs or returns will be accepted.
The reference design contains lethal voltages and high power RF. Use safety precautions.
1/28 http://www.microsemi.com
Microsemi PPG
Application Note
Contents 1. 2. 3. 4. INTRODUCTION DESIGN CONSIDERATIONS THEORY OF OPERATON CIRCUIT DESCRIPTION a. PULSE GENERATION b. RF OUTPUT MATCHING c. DC SUPPLY
5. TEST REQUIREMENT a. TEST SET UP DIAGRAM b. TEST REQUIREMENT 6. PERFORMANCE (DATA SUMMARY) a. POWER AND VOLTAGE GRAPHS b. VDS WAVEFORMS FOR VARIOUS HV PS 7. CONCLUSION 8. REFERENCES APPENDIX APPENDIX APPENDIX APPENDIX APPENDIX I SCHEMATIC II PCB LAYOUT III PARTS LIST IV HEATSINK V TRANSFORMER CONSTRUCTON
2/28 http://www.microsemi.com
Microsemi PPG
Application Note
1.
INTRODUCTION
This application note contains the design procedures and measurement results for a 2KW 13.56MHz RF generator using a CLASS D Push-Pull amplifier. To optimize efficiency and minimize cost the design uses a DRF1300 Power MOSFET Hybrid from Microsemi. The DRF1300 consists of two high power gate drivers, two 500V 30A MOSFETs, and several internal bypass capacitors. The internal layout of the T4 hybrid package has been optimized to minimize stray inductances allowing the DRF1300 to operate at frequencies of over 30MHz. To support this application note the DRF1300/CLASS-D reference design is available from Microsemi. It allows designers to readily verify the principals of this application note and save weeks or even months of design work. It illustrates the high efficiency operation and critical PCB signal-ground layout required to minimize output/input noise interference. The reference design comes complete and is mounted to an aluminum heat sink. The user only needs to provide is power supplies, cooling fans and a load. 2. DESIGN CONSIDERATIONS
To design the high-efficiency high-power RF generator the following issues were addressed. a. Choice of design complexity and efficiency trade offs. b. Selection of an adequate output matching circuit using a matching tool, to achieve the wanted power, drain waveform and efficiency. c. Selecting parts capable of handling RF output of 2KW including by-pass capacitors in the DC circuit, design and construction of a wide-bandwidth, high-current toroidal inductor and transformer, and sufficient capacitors for output matching circuit. d. The design of a heat sink for the amount of power dissipated. (see Appendix IV). e. The design of the printed wiring board for a good ground, especially for the output matching circuit. f. Isolation techniques between power output and signal generation circuit
The table below is for the major specification of this RF Power Generator. Freq 13.56Mhz Output Power Voltage Current 2KW 250V 9.2A Table 1. Key Specification Efficiency 85%
3/28 http://www.microsemi.com
Microsemi PPG
Application Note
A Class D push-pull amp requires control circuitry, a pair of MOSFET switches, a transformer for combining two outputs that are 180 out of phase, and an output matching network for tuning/creating a sinusoidal output signal. Class D operation theoretically can provide 100% efficiency, but because of the MOSFET on resistance, switching cross over transients, and magnetic loses, applications with approximately 85% efficiency is more achievable.
Fig. 1 shows a simplified CLASS D push-pull circuit. The two input signals are 180 out of phase causing Q1 and Q2 to switch ON and OFF alternately. The turn ratio of Transformer (n/m) is 2/1 for this application. For an ideal switch, when Q1 is ON, its drain voltage Vd1 is zero and the Vdd on the center tap of the primary of transformer, is transformed to (2/1) Vdd on the secondary. Alternately, when Q2 is ON, the reverse polarity of (2/1) Vdd appears on the secondary. The ideal waveforms are shown in Fig.2. A key technical difficulty for this push pull RF application is the transformer. The high current, high frequency and high voltage require careful design considerations. The inductor (L) and capacitors (C1 and C2) form a tank circuit to form a sinusoidal RF signal into the 50 Ohm load.
4/28 http://www.microsemi.com
Microsemi PPG
Application Note
Fig. 3 Pulse Generation Circuit a. Pulse Generation The Pulse generation circuit operates from a 3.0VDC~5.5VDC supply. The 27.12MHz TCXO is divided down to 13.56MHz and split into two 180 out of phase signals by U2B. U2A and U3A allow pulse width adjustment of the two signal inputs to the DRF1300. The pulse width of each signal can be adjusted from 15nS to 35nS using Potentiometer R9 and R16 respectively. To minimize a conductive EMI, it is crucial to observe proper circuit layout with good ground conditions along signal lines, taking care to isolate them from the output switching noise. Fig. 4 shows waveforms of outputs of pulse generation circuit at pin 4 and pin 10 of U1.
Microsemi PPG
Application Note
Fig. 5 RF Output Matching and DC Supply Circuit b. RF Output Matching The output matching circuit was calculated by means of RF matching software tool (Smith Chart) to maximize power transfer to a 50 Ohm load at J1. The matching circuit consists of a custom built transformer (T1), shunt/series capacitors (C34 through C37) and a custom built series inductor (L1). The capacitors and inductor form a tank circuit that is used for matching and tuning. It is critical that the output stage consists of inductors, capacitors, wires, toroids and ferrite cores that can handle the high currents and voltages associated with a 2KW RF Generator. Please refer to the recommended parts list for the DRF1300/CLASS-D that is provided in the appendix. Transformers T1 for this type of application are not commercially available. The design of the transformer used in the DRF1300/CLASS-D took several iterations to overcome bandwidth and power issues. The low cutoff frequency was overcome by selection of a specialized core. Minimizing the transformer turn ratio to 1:2 or 1:3 was required to avoid power loss. Refer to the following equations. Po=(8/)*(Veff/2R) for Class D Push-Pull For the Drain load line R=(m/n)*Ro m = number of primary turns and n = number of secondary turns Ro=Output load In this app note, Ro = 50, m=1, n=2 therefore R=12.5
6/28 http://www.microsemi.com
Microsemi PPG
Application Note
The transformer design is comprised of four (material 61) ferrite cores and was wound with double enameled wire. It is highly recommendation to use AWG16 wire for both the primary and secondary winding of the transformer and then apply glass electrical tape, such as 3M 27, before winding on the core. The tape will provide added protection against voltage breakdown and arcing and avoid any interference between the twisted wire bundles. The detailed instruction of making the transformer is presented in Appendix V. Fig. 6 shows plots for output matching which consists of transformer and L match of Toroidal Inductor and Capacitors in series and Capacitors in shunt to ground.
Fig. 6 c. DC Supply
The high voltage DC supply (PS HV) circuit employs a RF choke coil (L2) and bypass capacitors (C27, C28 and C38) to minimize an interference with AC signal. Refer to Fig 5. The RFC of this coil L2 was designed for approximately 1K ohm at 13.56MHz with 11 turns AWG 14 enameled wire. The by-pass capacitors should be selected for a 2KV voltage rating. Refer to the parts list in the appendix for recommended parts. It is very crucial that the capacitors (C31 through C33) be located as close as possible to the center tap of the primary winding of power transformer T1 have a good RF ground. Fig 7 illustrates the capacitor location to T1 and the red circles indicate ground connections through a via to the bottom ground plane.
7/28 http://www.microsemi.com
Microsemi PPG
Application Note
8/28 http://www.microsemi.com
Microsemi PPG
Application Note
Cooling requirement: Testing is recommended to be performed using a water cooling system. If not available, should use enough heat sink to maintain performance with sufficient fan capacity such as several 150 CFM fans (5 inch size) A space of approximately 2.5 inches or higher between the fans and the bench floor should be allowed so that air flow is not impeded. It is recommended that an additional fan be directed onto the transformer to provide cooling for the magnetics that will extend allowable test time. Process for Turn-On/Off Power Supplies i. Turn on Driver power supply PS_2 (11V~12V per circuit requirement) ii. Then, turn on MOSFET PS HV and slowly increase to 40V iii. Then, turn on pulse generator supply PS_1 (3~4V per circuit requirement). iv. While monitoring the RF power and waveform from Drain, ramp up PS HV in steps, verifying the outputs are stable before proceeding to the next step. v. To turn off reverse the turn on procedure.
If the RF output waveform (Vds) and/or RF power level fluctuates, immediate shut down of MOSFET PS and determine fault before resuming test.
9/28 http://www.microsemi.com
Microsemi PPG
Application Note
Fig. 9
10/28 http://www.microsemi.com
Microsemi PPG
Application Note
Step 1 2 3 4 5 6 7 8 9 10 11 12 13
PS HV, V 100 120 140 160 170 180 190 200 210 220 230 240 250
Id, A 4.31 4.91 5.54 6.18 6.48 6.79 7.11 7.43 7.75 8.00 8.36 8.67 9.18
Pin, W 431 589 776 989 1,102 1,222 1,351 1,486 1,628 1,760 1,923 2,081 2,295
RF out, W 344 486 653 842 939 1044 1152 1270 1400 1500 1630 1770 1950
, % 79.8 82.5 84.2 85.2 85.2 85.4 85.3 85.5 86.0 85.2 84.8 85.1 85.0
Vds, V 200 232 270 310 340 360 370 390 420 430 480 506 535
Table 2 shows the typical performance and the several steps that should be observed before proceeding to the next step and ultimately to 2KW. The table list the input high voltage supply (PS HV), MOSFET drain current (Id), power in and power out with efficiency, and the voltage observed at MOSFET drain (Vds). Variation of efficiency vs. Pout is shown in Fig. 10 and PS HV vs. Vds is shown in Fig. 11. Efficiency is calculated using RF power output and DC input power of the power MOSFET. The efficiency in the table is at 13.56Mhz. It should be noted that Vds exceeded the maximum BVdss (500V) of the MOSFETs in steps 12 and 13. The excess voltage to achieve 2KW output power resulted from transformer leakage inductance and lack of the broadband transfer characteristics of the wire-coupled transformer. A 2KW power output can be achieved with a Vds less than 500V by further tuning and optimization of the transformer.
11/28 http://www.microsemi.com
Microsemi PPG
Application Note
Eff., %
Fig. 10
Vdrain, V
120
140
160
170
180
190 Vds, V
200
210
220
230
240
250
Fig. 11
HV PS vs. Vds
12/28 http://www.microsemi.com
Microsemi PPG
Application Note
Fig. 12
13/28 http://www.microsemi.com
Microsemi PPG
Application Note
Fig. 13
14/28 http://www.microsemi.com
Microsemi PPG
Application Note
Fig. 14
15/28 http://www.microsemi.com
Microsemi PPG
Application Note
Fig. 15
16/28 http://www.microsemi.com
Microsemi PPG
Application Note
Fig. 16
17/28 http://www.microsemi.com
Microsemi PPG
Application Note
This Application Note describes design of a 2KW, 13.56MHz, Class D Push-Pull, RF generator. A Microsemi DRF1300 Hybrid was used to overcome layout parasitics that simplified the design and providing a single low cost, high efficiency RF generator. Limitations in transformer bandwidth caused this application to exceed the 500V breakdown voltage of the MOSFETs while achieving 2KW. Transformer design can be further optimized to eliminate the peaking as shown in the Vds waveforms. The principles of this application note can be verified with the DRF1300/CLASS-D reference design from Microsemi. The reference design minimizes design time by allowing an engineer to evaluate the performance into a 50 Ohm load and provides a platform for more complex load matching. 8. REFERENCES -. Solid State Radio Engineering Herbert L. Krauss and Charles W. Bostian -. Application Note: Simple and Inexpensive High Efficiency Power Amp using New APT MOSFET Kenneth Dierberger 1994 -. Application Note: 3KW and 5KW Half-Bridge Class-D RF Generator at 13.56Mhz with 89% Efficiency and Limited frequency Agility DEI, Inc
18/28 http://www.microsemi.com
Microsemi PPG
Application Note
Fig.17
http://www.microsemi.com
Microsemi PPG
Application Note
Fig.18
PCB Lay-out
20/28 http://www.microsemi.com
Microsemi PPG
Application Note
21/28 http://www.microsemi.com
Microsemi PPG
Application Note
22/28 http://www.microsemi.com
Microsemi PPG
Application Note
Appendix V. Process of building the high-power high bandwidth transformer T1 Step 1. Cement two ferrite cores together using epoxy glue.
23/28 http://www.microsemi.com
Microsemi PPG
Application Note
Cut 2 9 inch lengths for the primary and 2 16 inch lengths for the secondary, these wires are double enameled 16 AWG wire. Critical to use AWG 16, enamel magnet wire (Belden 8074).
Step 4 Twist the two primary wires and the two secondary wires together using at least 7 twists per inch to maximize coupling. Secondary wire
Primary wire
24/28 http://www.microsemi.com
Microsemi PPG
Application Note
Step 5 Twist both pairs of remaining secondary wires together. Make wires assembly suitable for the shape of the ferrite cores assembly using bending and cutting.
Primary wires
Secondary wires
25/28 http://www.microsemi.com
Microsemi PPG
Application Note
Step 8 Pull the free ends of the wire bundle back through the ferrite cores.
26/28 http://www.microsemi.com
Microsemi PPG
Application Note
Pull the free ends of the wire bundle once more back through the ferrite cores.
27/28 http://www.microsemi.com
Microsemi PPG
Application Note
Finished transformer showing twisted wires through ferrite cores assembly with wire ends bent down to mount to printed wiring board. There is a 1:2 Turn Ratio, which means 1:4 Impedance ratio of the transformer.
28/28 http://www.microsemi.com