Electronic Specialties, Incorporated

2013

- Since 1967 -

For Automotive, Marine, Small Engine, HVAC & Industrial Technicians

10 NEW PRODUCTS INSIDE!!!

WWW.ESITEST.COM

PROFESSIONAL HAND HELD TEST EQUIPMENT

ELECTRONIC SPECIALTIES, INC. MODEL #180 LOADpro Dynamic Test Leads - new!

LOADpro Finds these problems FAST! High Corrosive Resistance Shorts to ground NEW PRODUCT! Open Circuits
LOADpro performs voltage drop test with the push of a button. On a 12 Volt system, pressing the switch applies a load of approximately .5 Amps across the circuit. This simple test finds problems in corroded wires & connections and shorts to ground. Watch our video and youll spend less time diagnosing wiring problems. Start doing voltage drops now! Diagnose faster and earn more $$$. Works with your existing DMM.

PATENTED
Applications: Automotive Heavy Duty Marine RV Equipment

SteadyPin Probe Tips

LOADpro features SteadyPin probe tips. Instead of a pointed probe, SteadyPin tips have a small recess at the tip that allows the probe to sit firmly on a male ECM or connector pin. Traditional pointed probes fail to give an effective connection and creates difficulties in completing manufacturer specific voltmeter tests.

BONUS KIT! #181 LOADpro Bundle includes #180 & #182

#182 Fundamental Electrical Troubleshooting - new!

Great book! 200 page guide to every aspect of electrical troubleshooting. Written by a mechanic for real world, hands-on testing. Batteries/Testing explained Relays, potentiometers,resistors, solenoids Voltmeters explained Finding shorts to ground Battery draws explained Corrosion causes Voltage drop explained How-to-read schematics

MODEL #190 Relay Buddy - 12V Relay Tester - new!

NEW PRODUCT!

PATENT PENDING
NEW PRODUCT!

Quick off-the-car relay tester. Checks relay coil & switch contacts Fails bad relays Automatic test with Good/Bad indication
Relay Buddy is a quick go / no-go tester for the most common automotive relays. It provides you with an indication of the general health and functioning of the relay switch contacts and coil. Relay Buddy will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.

Applications: Automotive Heavy Duty Marine RV Equipment

Specifications:

- Settable to 4 and 5 pin relay - Tests 12V relays - Switch contact are loaded to detect excessive resistance - Uses vehicle 12V battery for power - Green Light if relay is good - Red Light if relay is bad

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC. MODEL #230 Short Buddy - Audible Trouble Shooter - new!

SHORT BUDDY Helps you finds these problems! Locating Shorts To Ground NEW PRODUCT! Intermittent shorts Intermittents caused by loose connections
Blowing Fuses?? Short Buddy helps you find the short! This unique tool connects at the fuse panel and becomes in series with the test circuit. A system of audible beeps helps you find the problem and permit hands free troubleshooting. Have a dead short? Short Buddy gives you continuous re-set/re-power capability, a real time saver. While you wiggle, pull, and grab wires, Short Buddy is always watching the current level. If your tug causes the dead short again, Short Buddy opens the circuit for 10 seconds, then re-applies power to the circuit. Re-powering the circuit can also be done manually. Another big feature! If the circuit current changes by more than approximately .3 Amps, youll hear an audible beep. If you pull on the problem wire or connector, youll hear the beep. When working under the dash or in a difficult area this is a huge help. Great tool for shorts, intermittent drop outs and flaky grounds & connections. A real time saver.

PATENT PENDING

Applications: Automotive Heavy Duty Marine RV Equipment

Specifications:

- Settable Amp Levels of 10, 15, 20, 25 and 30 Amps - Automatically opens the circuit in event of overload - In Auto mode, circuit gets re-powered in 10 seconds - In Manual mode, user re-sets power to circuit

MODEL #902 Code Buddy +Plus - new!

- OBDII Code Scanner w/Live Data Features:
RETRIEVE CODES generic (P0, P2, P3 and U0) and manufacturer specific (P1, P3 and U1) View FREEZE FRAME DATA Display LIVE DATA STREAM Turn off Check Engine Light (MIL), CLEAR CODES and reset monitors Identifies PENDING CODES Retrieve Vehicle Info - VIN NUMBER & CALIBRATION ID Works on all 1996 and later OBDII compliant US, European and Asian vehicles. Easily determines the cause of the Check Engine Light (MIL) Small in size and conveniently fits in hand - Reliable and Easy to Use Supports CAN all other current OBDII protocols; (ISO9141, KWP 5BAUD INIT, KWP ADDR INT, KWP FAST INIT, J1850 PWM, J1850 VPW) Specifications: Display BACKLIT, 128x64 pixel Operating Temperature: 32F to 140F (0C to 60C) Power: 10 to 15 volts provided by the vehicle

NEW PRODUCT!

Works with all 1996 and later OBDII compliant US, European and Asian vehicles Supports CAN (Controller Area Network) Tri-Lingual English/Spanish/French

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC. MODEL #TMX-589 TECH METER KIT - new!

Endorsed by: Bryan Lewis 2 Time Super Tech Grand Champion ASE Master Tech Diesel Instructor at Southside Virginia

Community College

HYBRID TECH METER KIT - Techs want more information! With TMX-589 NEW PRODUCT! SAFE! you get it! One hour of DVD training showing how to use and get the best results from your investment. You spoke, we listened! TEST RANGES: INCLUDES: DC Volts: 0-400mV, 4V, 40V, 400V, 1000V AC Volts: 0-400mV, 4V, 40V, 400V, 1000V TMX-589 - Professional Grade True RMS Digital Mulitmeter - CATIII 1000V safety DC Amps: 0-400uA, 4000uA, 40mA, 400mA, 10A AC Amps: 0-400uA, 4000uA, 40mA, 400mA, 10A rating - Safe for use on Hybrids - Waterproof/Dustproof to IP67 Standards Ohms: 0-400, 4K, 40K, 400K, 4M, 40M LOADpro - Loads the circuit to find corrosion and resistance in the Capacitance: 0-40nF, 400nF, 4uF, 40uF, 400uF 4mF, 40mF wiring - fast diagnosis - OEM approved tool - patented method cant be Frequency: 0-4Hz, 40Hz, 400Hz, 40kHz, 400kHz, 10MHz Type K Temp: -4F to 1400F, -20C to 760C accomplished by Power Probe IR Temp: -22F to 1022F, -30C to 550C FET Book - 200 pgs of Fundamental Elecrical Troubleshooting tips and insight Continuity: Audible Beep Diode Test: Diode Test A must have for any technician beginning or advanced Audible Continuity: Beep Peak Min/Max: 1 mS (1000 samples per second) Training DVD - One hour of multimeter training and testing tips - 10 separate Min/Max: Min-Max @ normal sample rate (2 per sec) videos covering each major function by Dan Sullivan - leading electrical trainer Auto Power Off: 30 minutes Shock/Drop Test: 6.5 Feet (2 meters) Compass - Used for Alternator and solenoid diagnostics Bryan Lewis ~ No matter what skill level you have, this kit will build your confidence
and provide an easier way to diagnose electrical circuits without piercing wires

MODEL #597IR PREMIUM AUTOMOTIVE METER (#597 No IR Thermometer)

Two models available - #597IR includes IR Thermometer and #597 is without thermometer. #597 is equipped for advanced automotive diagnostics. #597 is a CAT III 1000 Volt rated meter, therefore safe to use on Hybrids. #597IR includes our model EST-100 Infrared Thermometer Adapter, for measuring surface temps up to 1022F or 550C. The Peak Min/Max function measures transient voltages as fast as 1 Millisecond. #597 also measures the ON-TIME (pulse width) of fuel injectors and features a desirable 20 Amp test range. #597 is even waterproof to IP67 standards thats right, if you drop it into water, it floats! The #597IR includes IR Thermometer, test leads, Inductive RPM pick-up, temperature probe, 9 volt battery, instructions manual and hard storage case. Inductive RPM pick-up features a five position, adjustable sensitivity switch. #597 same as #597IR but without thermometer.
TEST RANGES:

Features:
CAT III 1000 Volt rated - safe to use w/Hybrids Waterproof to IP67 standards 48 Test Ranges, 18 Test Functions EST-100 IR Thermometer w/8 to 1 distance ratio Backlit LCD display with analog bargraph 1 Ms Peak Min/Max function for glitch capture Ms Pulse Width for fuel injector on-time Desirable 20 Amp Fused Test Range Data Hold, Auto Power-Off, + Trigger Adjust Also measures temp via K-type probe Modern design, protective holster built-in

Blow Mold Storage Case Included

DC Volts: AC Volts: DC Amps: AC Amps: Ohms: Capacitance:

0-400mV, 4V, 40V, 400V, 600V 0-4V, 40V, 400V, 600V 0-40mA, 400mA, 20A 0-40mA, 400mA, 20A 0-400, 4K, 40K, 400K, 4M, 40M 0-4nF, 40nF, 400nF, 4uF, 400uF, 4mF, 40mF Frequency: 0-2kHz, 40kHz, 400kHz, 40MHz Duty Cycle: 0.1% - 99.9% Type K Temp: -22F to 1832F, -30C to 1000C IR Temp: -22F to 1022F, -30C to 550C Pulse Width: 2.0ms - 10.0ms RPM: 0-4,000 RPM, 12,000 RPM x 10 RPM/DIS: 0-4,000 RPM, 6,000 RPM x 10 Dwell: 4 cyl, 5 cyl, 6 cyl, 8 cyl Continuity: Audible Beep Diode Test: Diode Test

HYBRID SAFE!
CAT III 1000 Volt Safety Rated IP67 Waterproof/Dustproof

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC. MODEL #595 PRO MODEL AUTOMOTIVE METER W/PC INTERFACE
The #595 is a premier automotive diagnostic tool. The #595 features a huge LCD display w/bargraph for easy viewing. It can be interfaced to your PC or notebook computer for enhanced diagnostics and data presentation. The software and interface cable are included free! The #595 includes two test lead sets , RPM pick-up, temp probe, software CD, interface cable, protective holster, 9V battery, instructions manual and hard storage case. Inductive RPM pick-up features a five position, adjustable sensitivity switch. CATIII 1000V, safe for use on hybrids. Features:
CAT III 1000 Volt rated - safe to use w/Hybrids 58 Test Ranges, 16 Test Functions Huge Backlit LCD display w/analog bargraph Ms Pulse Width for fuel injector on-time Max/Min better diagnostic capability 4 Step adjustable trigger levels RS-232 PC Interface Desirable 20 Amp fused test range Special access panels for fuses Hard Storage Case for safe storage Auto Power-Off, saves batteries TEST RANGES:
DC Volts: AC Volts: DC Amps: AC Amps: Ohms: Capacitance: RPM 4: RPM2/DIS: Dwell: Frequency: Duty Cycle: Pulse Width: Period: Temperature: Continuity: Diode Test: 0-400mV, 4V, 40V, 400V, 1000V 0-400mV, 4V, 40V, 400V, 750V 0-400uA, 4mA, 40mA, 400mA, 4A, 20A 0-400uA, 4mA, 40mA, 400mA, 4A, 20A 0-400, 4K, 40K, 400K, 4M, 40M 0-40nF, 400nF, 4uF, 40uF, 100uF 0-4,000 RPM, 12,000 RPM x 10 0-4,000 RPM, 6,000 RPM x 10 1, 2, 3, 4, 5, 6, 8, 10, & 12 cyl. 0-5Hz, 50Hz, 500Hz, 5kHz, 30kHz 0.1% - 99.9% 2.0ms - 10.0ms 2.0ms - 20.0ms -4F to 1400F, -20C to 760C Audible Beep Diode Test

CAT III 1000 Volt Safety Rated

HYBRID SAFE!
595 PC Interface test screen

MODEL #590TRMS PROFESSIONAL AUTOMOTIVE DMM MODEL #590 PROFESSIONAL AUTOMOTIVE DMM
Another good choice for the professional automotive technician, the #590TRMS features TRUE RMS readings on AC Volts and AC Amps for better accuracy. #590TRMS/#590 puts the right capabilities in your hands. For example, each model can test the on-time of fuel injectors using the Ms pulse width test function. This DMM is completely auto-ranging, making it an easy and efficient tool to use. #590TRMS/#509 includes two sets of test leads, RPM pick-up, temperature probe, 9 volt battery, instructions manual and carrying case. Inductive RPM pick-up features a five position, adjustable sensitivity switch. NOTE: Model #590 is the same as #590TRMS but uses average reading method on AC Volts & AC Amps (not True RMS). Features:
True RMS accuracy (model 590TRMS) 48 Test Ranges, 15 Test Functions Auto-ranging Modern design, protective rubber boot and case are all one piece Huge 2 inch high LCD display with backlighting, easy to see digits! Ms Pulse Width for fuel injector on-time Desirable 20 Amp fused test range Auto Power-Off, saves batteries Relative change function, Data Hold Built-in Temperature readings Includes zippered storage case
Dwell 4 cyl, 5 cyl, 6 cyl, 8 cyl Duty Cycle 0.1% - 99.9% Capacitance 0-40nF, 400nF, 4uF, 40uF, 100uF Frequency 0-5Hz, 50Hz, 500kHz, 5kHz, 50kHz, 500kHz, 10MHz Temp -20C to 760C, -4F to 1400F Continuity Audible Beep Diode Diode Test

MODEL #590/ 590TRMS INCLUDE CARRYING CASE

TEST RANGES:
DC Volts AC Volts DC Amps AC Amps Ohms RPM 4 RPM 2/DIS PulseWidth 0-400mV, 4V, 400V, 1000V 0-4V, 40V, 400V, 700V 0-40uA, 400mA, 4A, 20A 0-40uA, 400mA, 4A, 20A 0-400, 4K, 40K, 400K, 4M, 40M 0-4,000 RPM, 0-12,000 RPM x 10 0-4,000 RPM, 0-6,000 RPM x 10 1 - 10 mS

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC. MODEL #585K DELUXE AUTOMOTIVE METER WITH RPM & TEMPERATURE
#585K is a professional grade DMM used for diagnosing electrical, computer and engine problems on any vehicle. Our best selling meter, #585K is auto-ranging on DC Volts, AC Volts and Ohms. The kit includes two sets of test leads, RPM pick-up, temperature probe, protective holster, 9 volt battery, instructions manual and carrying case. Inductive RPM pick-up features a five position, adjustable sensitivity switch. Features:
45 Test Ranges, 14 Test Functions RPM for DIS & standard ignitions Dual display w/analog bargraph and digital readings Built-in temperature readings RPM pick-up & temperature probe included 10 Meg/Ohm Input Impedance Dual fuse protection Safety leads & jacks Built-in tilt stand 9V battery installed
Dwell 2 cyl, 3 cyl, 4 cyl, 5 cyl, 6 cyl, 8 cyl Duty Cycle 1.0%-90% Frequency 0-320Hz, 3200Hz, 32kHz Temp -20C to 320C, -20C to 750C -4F to 320F, -4F to 1400F Continuity Audible Beep Diode Diode Test

MODEL #585K INCLUDES CARRYING CASE

TEST RANGES:
DC Volts AC Volts DC Amps AC Amps Ohms RPM 4 RPM 2/DIS

0-320mV, 3.2V, 32V, 320V, 1000V 0-3.2V, 32V, 320V, 1000V 0-320uA, 3.2mA, 32mA, 320mA, 10A 0-320uA, 3.2mA, 32mA, 320mA, 10A 0-320, 3.2K, 32K, 320K, 3.2M, 32M 0-3200 RPM, 12,000 RPM x 10 0-3200 RPM, 6,000 RPM x 10

M U L T IM E T E R S E L E C T IO N C H A R T
1 M s P e a k M in /M a x C A T I II 1 0 0 0 V - H y b r id In d u c tiv e R P M M s P u ls e W i d t h T r u e R M S o n A C V /A R S - 2 3 2 P C In te r fa c e A n a lo g B a r G r a p h T e m p e r a tu r e D w e ll D u t y C y c le F re que nc y A u d i b le C o n t i n u i t y D io d e T e s t D C V M a x im u m A C V M a x im u m A C C u r r e n t M a x im u m D C C u r r e n t M a x im u m # of Test R anges # o f T e s t F u n c tio n s T M X -5 8 9 X X

597
x x x x

595
x x x x x x x x x x x 1000V 1000V 20A 20A 58 16

590TR M S
x x x

590
x x

585
x

385A
x

480A

380

501

X X X x x x x x x x 600V 600V 20A 20A 48 18

X X X 1000V 1000V 10A 10A 44 11

x x x x x x 1000V 700V 20A 20A 48 15

x x x x x x 1000V 700V 20A 20A 48 15

x x x x x x x 1000V 1000V 10A 10A 45 14

x x x x x 600V

10A 25 9

x x x x 600V 600V 10A 10A 43 10

x x 1000V 750V 10A 10A 20 7

x 500V 500V 200m A 16 6

MODEL #142 PRO TEST LEAD KIT

Includes:
One set of Interconnect Leads - Extended length of 64 inches. Test probes Flexible Silicon Back Probe Pins Bed of Nails Type Wire Piercing Clips Heavy Duty Insulation Piercing Clips Crocodile Clips Deluxe Storage Pouch Compatible with virtually all DMMs
Applications: Automotive Industrial HVAC Electrical Marine

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC. MODEL #385A DIGITAL ENGINE ANALYZER/MULTIMETER

#385A has many of the necessary features required for todays automotive diagnostics. Use frequency readings to test crankshaft and camshaft sensors, for example. The #385A comes equipped with an RPM pick-up, probe test leads, alligator clip test leads, protective holster, instructions and installed 9V battery. Inductive RPM pick-up features a five position, adjustable sensitivity switch. Features:
25 Test Ranges, 9 Test Functions Easy RPM readings Inductive RPM pick-up included 10 Meg/Ohm Input Impedance Dual Fuse Protection Built-in tilt stand 10 Meg/Ohm Input Impedance TEST RANGES:
DC Volts DC Amps Frequency RPM Ohms Duty Cycle Dwell Continuity Diode 0-200mV, 2V, 200V, 600V 0-10A 0-200Hz, 2000Hz, 20kHz 0-2000, 12,000 0-200, 2K, 20K, 200K, 2M, 20M 1.0% - 90% 3 cyl, 4 cyl, 5 cyl, 6 cyl, 8 cyl Audible Beep Diode Test

MODEL #480A AUTO-RANGING DIGITAL MULTIMETER

The #480A is a high precision Auto-ranging DMM that can help you troubleshoot all types of electrical problems. Just set to the desired test function and the unit automatically selects the proper test range. Includes test leads, protective holster, instruction manual and two AA batteries. TEST RANGES: Features:
43 Test Ranges, Auto-Ranging 10 Test Functions Auto Power-Off, Data Hold Dual Fuse Protection 10 Meg/Ohm Input Impedance
DC Volts: AC Volts: DC Current: AC Current: Resistance: Frequency: 0-400mV, 4V, 40V, 400V, 600V 0-400mV, 4V, 40V, 400V, 600V 0-400uA, 4mA, 40mA, 400mA, 10A 0-400uA, 4mA, 40mA, 400mA, 10A 0-400, 4k, 40k, 400k, 4M, 40M 0-9.999Hz, 99.99Hz, 999.9Hz, 9.999kHz, 99.99kHz, 999.9kHz, 9.999MHz Capacitance: 0-4nF, 40nF, 400nF, 4uF, 40uF Duty Cycle: 0.1%-99.9% Diode: Diode Test Continuity Test: Audible Beep

MODEL #380 DIGITAL MULTIMETER

This digital multimeter has the compact design and the functions you need for overall convenience. Its capabilities are equal to many higher priced multimeters. Comes with test leads, protective holster, instructions and installed 9 volt battery.
TEST RANGES:
DC Volts AC Volts DC Amps Ohms 0-200mV, 2V, 20V, 200V, 1000V 0-200V, 750V 0-200uA, 20mA, 200mA, 10A 0-200, 2000, 20K, 200K, 2M, 20M Continuity Test Diode Transistor Audible Beep Diode Test Transitor Test

Features:
20 Test Ranges, 7 Test Functions 10 Amp test range Continuity beeper Fully fuse protected 10 Meg/Ohm impedance

MODEL #501 DIGITAL MINI MULTIMETER

This is an economical digital multimeter that cant be beat. The #501 has the capabilities of full range units but is small enough to fit in your pocket. Its low price will surprise you! Includes test leads, protective holster, instructions and installed battery.
TEST RANGES:

Features:
16 Test Ranges 3 1/2 Digit LCD display 6 Test Functions Fuse protected Protective Holster Included Safety leads & jacks

DC Volts AC Volts DCAmps Ohms Battery Test Diode

0-200mV, 2000mV, 20V, 200V, 500V 0-200V, 500V 0-2mA, 20mA, 200mA 0-200, 2000, 20K, 200K, 2000K 0-9V Diode Test

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC. MODEL #550 INSULATION TESTER

#550 is used to check high voltage circuits on Hybrid vehicles, for leaks to ground. #550 can supply 250V, 500V and 1000V test voltages for doing complete insulation testing. You can not easily test for high voltage leakage without a high volt test source. #550 is auto-ranging and can measure up to 2000 MegaOhm with resolution of 1 K Ohm. Features:
Meets IEC10101, CATIII 1000V Large dual display with white LED backlighting Test Hold function for easy operation Low battery indication Includes (6) AA batteries, test leads & blow mold case TEST RANGES:
DC Volts AC Volts Insulation Resistance: Ohms: Test Voltage: 0-750V 0-1000V 0-200MegOhm, 2000MegOhm 0-400, 2000 250V-200MegOhm 500V-200MegOhm 1000V-2000MegOhm Audible Beep

ContinuityTest:

MODEL #655 HIGH CURRENT PROBE/DMM

Another great tool for all around electrical troubleshooting. #655 is ideal for all high current applications, especially starting and charging diagnostics. #655 can measure up to 1000 Amps AC or DC. Unit features built-in degrees F and C temperature readings. Includes test leads, temp probe, instructions, 9V battery and carrying case. Features:
37 Test Ranges 10 Test Functions Auto Power Off Auto-Ranging, Data Hold Temp probe included Continuity Beep Overload Protection Clamp opening 1.5 inches Test Leads Included Carrying Case included TEST RANGES:
DC Amps AC Amps DC Volts AC Volts Ohms Frequency 0-40A, 400A, 1000A Temperature -4F to 1832F & 0-40A, 400A, 1000A -20C to 1000C 0-400mV, 4V, 40V, 400V, 600V Duty Cycle 0-.5%-99.0% 0-400mV, 4V, 40V, 400V, 600V Continuity Audible Beep 0-400, 4k, 40k, 400k, 4M, 40M Diode Diode Test 0-5Hz, 50Hz, 500Hz, 5kHz, 50kHz, 100kHz Capacitance 0-40nF, 400nF, 4uF, 40uF, 100uF

MODEL #685 CURRENT PROBE/DMM

The #685 is a great tool for all purpose electrical testing. Applications include: fuel injection systems, fuel pumps, charging systems, electric motors, and most parasitic drains. Capable of measuring as low as 10 milliamps! Features:
35 Test Ranges 10 Test Functions Auto Power Off Auto-Ranging Data Hold Continuity Beep Overload Protection Clamp opening 7/8 inches 9 Volt Battery Included Carrying Case included

TEST RANGES:
DC Amps AC Amps DC Volts AC Volts Ohms Frequency 0-40A, 200A 0-40A, 200A 0-400mV, 4V, 40V, 400V, 600V 0-4V, 40V, 400V, 600V 0-400, 4k, 40k, 400k, 4M, 40M 0-10Hz, 100Hz, 1000Hz, 10kHz, 100kHz, 1000kHz, 10MHz Capacitance 0-4nF, 40nF, 400nF, 4uF, 200uF Duty Cycle 0-.5%-99.0% Diode Diode Test Continuity Audible Beep

MODEL #687 LOW CURRENT PROBE/DMM

With the capability of measuring down to 1 milliamp (.001A), the #687 is a great tool for all low current applications. Especially for diagnosing parasitic drains! Clamp opening is large enough to fit over most negative battery cables. TEST RANGES: DC Amps 0-4A, 80A Applications: fuel injectors, fuel pumps, electric AC Amps 0-4A, 80A motors, battery drains, charging systems. DC Volts 0-400mV, 4V, 40V, 400V, 600V Features:
35 Test Ranges 10 Test Functions Auto Power Off Auto-Ranging Data Hold Continuity Beep Overload Protection Clamp opening 5/8 inches 9 Volt Battery Included Carrying Case included
AC Volts 0-400mV, 4V, 40V, 400V, 600V Ohms 0-400, 4k, 40k, 400k, 4M, 40M Frequency 0-5Hz, 50Hz, 500Hz, 5kHz, 50kHz, 500kHz, 5MHz, 10MHz Capacitance 0-40nF, 400nF, 4uF, 40uF, 100uF Duty Cycle 0-.5%-99.0% Diode Diode Test Continuity Audible Beep

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC. MODEL #695 LOW CURRENT PROBE FOR GRAPHING METERS, SCOPES & DMMs
Great tool for accurate measurement of low current. Works with your graphing meter or lab scope to view current waveforms on fuel injectors, fuel pumps, primary ignition coils and more. Also works well with digital multimeters. Resolution of 10 milliamps is low enough for most parasitic drain testing. Clamp opening of 1/2 inch is large enough to clamp over most negative battery cables for those parasitic drain tests.
TEST RANGES:
DC Amps 0-20A, 80A (resolution .01A) AC Amps 0-20A, 80A (resolution .01A)

Features:
Compatible with many lab scopes and graphing multimeters Use to generate current waveforms for diagnostic analysis Also works great with digital multimeters Jaw opening of 1/2 inch clamps over most negative battery cables Low battery indication, Auto Power-Off

MODEL #697 CURRENT PROBE - 400 AMPS

Use this instrument to test starting and charging systems. It can even be used to test relative compression when used with your lab scope or graphing meter. Unit is designed for use with digital multimeters, lab scopes or graphing meters. Output of the probe is 1mV/Amp. Features:
Great tool for testing starting and charging systems One touch zero adjust and low battery indication Works with digital multimeters, scopes or graphing meters High current measuring capability, up to 400 Amps AC/DC Unit also features Auto Power-Off - saves batteries TEST RANGES:
DC Amps AC Amps 0-400A (resolution .1A) 0-400A (resolution .1A)

#698 HIGH CURRENT PROBE - 1000 AMPS

Unit is designed for use with digital multimeters, lab scopes or graphing meters. Ideal unit for high current applications like heavy duty starting and charging systems. Features:
Measures 0 to 1000 Amps DC or AC Great tool for testing starting & charging systems Jaw opening is 2.125 inches Zero Adjust Knob Zippered Carrying Case Included

MODEL #640 D.V.A. ADAPTOR

Features:
Read peak volts on CD ignition coils w/your existing DMM Adapts standard digital multimeter into peak reading voltmeter OEM tool for several outboard engine manufacturers Fits most DMMs

TEST RANGES:
DC Amps AC Amps 0-600A, 1000A (resolution .1A) 0-600A, 1000A (resolution .1A)

MODEL #530 D.V.A. /PEAK READING MULTIMETER

The #530 was designed in conjunction with the industrys leading outboard engine manufacturers. The #530 is used to diagnose problems in CD (capacitive discharge) ignition systems. An essential tool for the professional marine service TEST RANGES: technician. DVA Volts 0-2V, 20V, 40V, 200V, 400V
DC Volts AC Volts DC Amps Ohms 0-2V, 20V, 40V, 200V, 400V 0-20V, 40V, 200V, 400V 0-10A x1, x10, x100, x1000

Features:
Analog multimeter with peak reading capability Fuse protected and includes a spare fuse Complete with battery and storage case Use to diagnose defective CD ignition coils

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC. MODEL #301M - #302M - #303B - #304B - #305M - #306B FUSE BUDDY TESTERS
TM

Model 302M
0-20 Amps - .01A res. for Mini Fuse

Model 304B
0-20 Amps - .01A res. for ATC Fuse

Model 305M
0-30 Amps - .1A res. for Mini Fuse

Model 306B
0-30 Amps - .1A res. for ATC Fuse

Get the FUSE BUDDY, a great new product. Can test circuit current up to 20 OR 30 Amps - an easy way to check fuel pump amperage. Clever design allows for easy connection into fuse sockets. FUSE BUDDYs are available as stand alone Tester or DMM Adapter, for both Mini & ATC fuses Fuse Buddy ends are molded into the shape of the fuse itself. During testing the fuse is removed and replaced into the Fuse Buddy. This way, the circuit being tested maintains fuse protection. #302M & #304B can even be used to test for parasitic drains! #305M & #306B can be used to test blower motors!

Model 301M
0-20 Amps for Mini Fuse DMM determines max current range Readings displayed on DMM or scope

Model 303B
0-20 Amps for ATC Fuse DMM determines max current range Readings displayed on DMM or scope

MODEL #310 FUSE BUDDY PRO TEST KIT

THREE TESTERS IN ONE!! Great new tool with 3 interchangeable test functions. 1) 30 Amp MINI - Circuit Amperage Testing 2) 30 Amp ATC - Circuit Amperage Testing 3) 30 Amp All Purpose Amperage Testing The new Fuse Buddy Pro Kit can read amperage draws on both ATC and Mini fused circuits up to 30 Amps. As an added bonus, the Fuse Buddy Pro can be used as an all purpose amp meter with the included 30A test clips. Quick and easy way to check circuit amperage draws Check blower motor and fuel pump amperage draws Installing an auto-resetting circuit breaker allows you to check for intermittant shorts and monitor the current draw at the same time Also handy for checking current readings on A/C compressors that are not easily accessible Deluxe LCD display features full ANALOG BAR GRAPH Unit features DATA HOLD and AUTO POWER-OFF Resolution: .1A (100 mA) - Accuracy: +2% of reading Measurement range: 0 to 30 Amps / 48 Volts

TM

MODEL #315 MAX FUSE BUDDY KIT

Now a Fuse Buddy tester for Maxi fuse circuits! Max Fuse Buddy can test up to 80 AMPS. There are numerous Heavy Duty & Automotive applications. With supplied adapters, #315 can also work with MINI and ATC circuits. Top 20 Tool Winner in 2009. Easy access to measure amperage draws in MAXI, MINI & ATC circuits Can measure up to 80 Amps DC on MAXI fuse circuits MAX FUSE BUDDY test applications include: Anti-Lock Brake Circuits Car Stereo Circuits Power Distribution Circuits Branch Circuits Rear Window Defogger Circuits Solar Power DC Branch & Traction Control Circuits Charge Controller Circuits Heavy Duty Equipment Ciruits Fire Engine Water Pumps Unit features PEAK HOLD and DATA HOLD functions Deluxe LCD display features full ANALOG BAR GRAPH Resolution: .1A (100 mA) - Accuracy: +2% of reading Measurement range: 0 to 80 Amps / 48 Volts DC Includes one 20 Amp MAXI fuse for use with MINI & ATC circuit testing

TM

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC. MODEL #307 & #308 FUSE BUDDY CURRENT LOOPS
Plug a Fuse Buddy Current Loop into a circuit and now you can clamp your current probe over the wire to read the amp draw. Great accessory for any current probe or automotive scope Just clamp your current probe over the loop to access the amperage draw through a fused circuit. Easy testing access, plugs right into fuse socket, no more hand made adapters. Testing range 0-30 Amps Do Not Exceed 30 Amps Can be used to diagnose a variety of amp draw problems including:
Fuel Pumps Battery Drains Blower Motors Shorts
TM

#307M

#308B

MODEL #136 & #138 MAG LEAD TEST LEAD SYSTEM

Need to stick to a good ground or test point? Get the Mag Lead, a great new product. Mag Lead features a magnetic disconnect near the test probe end - no affect to the readings. Just disconnect the test probe and you can stick to any metallic ground or test point. This is a time saving tool - if you dont have to walk to your tool box to retrieve your alligator clips, even Magnetic connector here on just half the occasions, then youve saved time. Can eliminate the need to hold probes while checking or monitoring a signal. Fits almost all Digital Multimeters and can be used with hand-held scopes too. Get the Mag Lead, it stays put and wont fall off!

Magnetic connector here

#136 MAG LEAD SET PATENTED

#138 MAG LEAD SET w/ Alligator Clips

MODEL #134 FUSE LEAD Automotive DMM Test Leads - new!

Automotive Fuse Holder In-Line Can Prevent Your DMMs Internal Fuse From Blowing - TIME SAVER!
ATC Fuse Holder In-Line Provides extra overload protection Can prevent your DMMs internal fuse from blowing For use with any Digital Multimeter
NEW PRODUCT!

MODEL #143 Automotive Test Lead Kit - new!

Test Lead Kit includes our basic set of interchangeable specialty test probes designed for automotive use. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. The large Crocodile Clips are good for clipping to grounds and battery terminals. Roll up storage pouch keeps your leads organized.
NEW PRODUCT!

Includes: One set of Interconnect Leads length 64 inches Test Probes Flexible Silicon Back Probe Pins Shielded Alligator Clips Large Crocodile Clips Deluxe roll-up Storage Pouch

#142-5 Automotive Back Probe Pins - new!

Flexible 1.5 inch silicon pins provide easy back probing connections for DMM and Scope measurements Great for back-probing harness connectors and automotive sensors Flexible silicon bends for difficult areas Can be used up to 30 Volts Connects to test leads w/removable ends

NEW PRODUCT!

Applications: Automotive Heavy Duty Equipment RV Marine

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC.

#EST-75 HIGH TEMP IR THERMOMETER - PRO MODEL
EXTREME HIGH TEMP RANGE, UP TO 1832F High quality, professional tool Long distance to spot ratio of 12 to 1 Zippered carrying case included More capability per dollar than the competition. Temperature Range: -58 to 1832F (-50 to 1000C) Accuracy: + 1.5% of reading Distance to Spot Ratio: 12 to 1 Emissivity = 0.95 9 Volt Battery Included

MODEL #703 COMPRESSION TESTER

Features:
Tester screws into 14 mm spark plug hole on outboard engines and similar. Use to check for low compression Measures up to 200 Psi or 14 Kgs Check for burnt valves, scored cyls, leaking head gaskets, broken valve springs, rings & damaged pistons

All IR Temp Units Feature:

Built-In Laser Pointer F/C Switchable Backlit LCD Display 0.1 Degree Resolution Data Hold Auto Power-Off

MODEL #701 VACUUM GAUGE AND FUEL PUMP TESTER

Features:
Large 3 1/2 diameter face English and metric scales Vacuum: 0-30 inch Hg. and 0-600 mm Hg. Fuel pump pressure: 0-10 Psi and 0-7 Kg/Cm2 Heavy duty tubing and vacuum fitting included Check for leaky valve timing, fuel pump vacuum and gas line leakage

#EST-67 TWIN LASER IR THERMOMETER

Twin Laser Pointers for Precise Accuracy Lasers converge at optimal measuring distance Temp Range: -58 to 1022F (-50 to 500C) Distance to Spot Ratio: 12 to 1 Continuous Max Hold Feature Continuous Backlit Display - Easy to See Fast response time (150 Ms) for quick work High Accuracy Rating of +1% Carrying Case Included One year warranty

#702 UNIVERSAL COMPRESSION TESTER

Features:
Measures pressure in both English and metric: 0-300 Psi and 0-21 Kgs Quick-connect coupler - fast and easy to use Burn resistant steel braided flex hose Includes 6 straight and 13 flexible hose with 14/18 mm adaptor For diagnosing: burnt valves, broken valve springs, broken rings, worn or damaged pistons, scored cylinders, leaking head gaskets, etc.

#EST-65 INFRARED THERMOMETER

High quality construction w/rubber insert in grip, nose & LCD areas. High temperature range Temperature Range: -58 to 1022F (-50 to 500C) Carrying case included Accuracy: + 2% of reading Distance to Spot Ratio: 8 to 1 Emissivity = 0.95 9 Volt Battery Included

#EST-35 IR THERMOMETER
Continuous Max Hold Feature Built-in Laser pointer - Backlit Display Data Hold & Auto Power-Off Carrying case included Front panel controls, not under handle Temperature Range: -22 to 500F/-30 to 260C Distance to Spot Ratio: 8 to 1 Resolution: 0.1 F/C Basic Accuracy: +2% Emissivity: = 0.95

#220 TRAILER BUDDY - 4/5 Pin Flat

#220 Tests 4 & 5 Pin Flat connector wiring #222 Tests 7 Pin Round connector wiring Each signal from vehicle emits a unique tone Loud beep can be heard over shop noise One person - complete test in 60 seconds! Just apply brakes, turn signals, running lights, engage reverse and listen. #222 also verifies 12 V charging signal as well as trailer brake signal Greatly reduces time spent verifying vehicle trailer wiring Very simple & easy to use - saves time!

#222 TRAILER BUDDY - 7 Pin Round

Lighting Circuits Tested: Left Turn Signal Right Turn Signal Brake Running Lights Reverse 12V Charging (#222) Trailer Brake Signal (#222)

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC. #720 DIGITAL BATTERY TESTER

Tests battery condition using patented dynamic resistance technology. Results display actual CCA capacity of battery w/pass/fail diagnosis. LEDs indicate the following PATENTED TECHNOLOGY 1. OK 2. OK & RECHARGE Specifications: 3. RECHARGE & RETEST CCA Test range: 200-1200 CCA State of Health: Actual Battery 4. BAD FAIL CCA displayed 5. BAD CELL Tester removes surface charge Rating Systems: SAE, DIN, EN, IEC & CA(MCA) Down to 1.5 Volts prior to battery test resulting in Tests Discharged: Temperature Compensation more accurate results.

#725 BATTERY & STARTING/ CHARGING SYSTEM TESTER

PATENTED TECHNOLOGY

6 & 12 V Battery Tester - 12 & 24 V Charging System Tester Tests battery condition and the starting/charging system. Guided test sequence covers - battery, cranking volts and charging system. Charging system test checks the alternator voltage and the AC ripple voltage for bad diodes. Specfications: Test results include the State of Health %, Batteries Tested: 6 and 12 Volt State of Charge % and actual CCA capacity. Charging Systems: 12 and 24 Volt Diagnosis of battery condition also displayed State of Health: Actual Battery CCA and %age 2 line LCD display in 7 languages Sate of Charge: Battery Voltage and %age CCA Test range: 40-2000 CCA Tests discharged batteries down to 1.5V
Rating Systems: SAE, DIN, EN, IEC & JIS Tests Discharged: Down to 1.5 Volts Temperature Compensation

State of Charge Display

MODEL #710 - 500 AMP CARBON PILE LOAD TESTER

The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.

State of Health Display

Features:
500 Amp adjustable load carbon pile Tests batteries rated as high as 1000 CCA or 160 Amp hour 15 second test with audible tone Can also test alternators, regulators and starters 500 amp side terminal clamps & heavy duty stranded copper cables Meters are color coded for simple pass or fail diagnostics Includes temperature compensation chart

#706 DIGITAL BATTERY TESTER

Automatic, simply activate the switch once for 10 second 100 Amp load. The #706 also tests charging voltage & relative starter current draw. Features:
DIGITAL DISPLAY - OK, WEAK or BAD AUTOMATIC TEST - Audible beep when test is complete. Unit indicates CHG if the pre-test state of charge is not sufficient for proper battery testing. 2 Year Warranty. Unique design = longer warranty.

MODEL #700 BATTERY TESTER

The #700 has an internal loading capacityof 100 amps. It is a great tool for finding batteries that cant stand up to the load of todays automotive accessories. Also tests relative starter current draw and charging voltage. Features:
Internal 100 Amp loading capacity Tests battery voltage, relative starter current draw, charging voltage and battery condition Heavy duty cable and copper plated clamps Convenient handle for carrying & hanging with heat protection

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC.

MODEL #332 PRO LASER TACHOMETER
Great tool for safe & accurate measurement of RPM in almost any environment. Just aim the laser beam at a reflective mark placed on a rotating device and the RPM reading is displayed. #332 can measure up to 99,999 RPM in 1 RPM increments. Use on coil-on-plug and diesel engines, where conventional inductive tachs cant be used. Other uses include generators, compressors, industrial engines, fans, gears and more. Zippered case, reflective tape, instructions & 9V battery included. Features:
TEST RANGE: 0-99,999 RPM High intensity laser beam, detects RPM from up to 6 feet away Memory function saves maximum and minimum RPM readings Reflective tape included

MODEL #325 EZ-TACH DIGITAL AUTOMOTIVE TACHOMETER

Features:
No wires, no cables, or fragile antennas! Conventional and DIS ignition capability 0-12,000 RPM on conventional ignitions 0-6,000 RPM on DIS ignitions Data Hold Low Battery Indication Just clamp over any spark plug wire! EZ-Tach gives accurate RPM readings quick and easy

MODEL #333 PRO LASER / CONTACT TACHOMETER

#333 is a dual function Laser Photo & ContactTachometer. Photo RPM measurements are taken via the laser photo method, same as model 332. Contact functions, including various rotation, distance and frequency measurements are made with the accessory heads. Zippered case, three contact adapters, reflective tape, instructions & 9V battery included. Features:
0-99,999 RPM - 12 Different Measurement Modes High intensity laser beam, detects RPM from up to 6 feet away Memory function saves up to 10 min/max/avg date records Reflective tape and 3 contact accessories included CONTACT MEASUREMENT MODES: RPM(contact) Frequency(Hz) Meters per minute Inches per minute Feet per minute Yards per minute Revolutions Length in Meters Length in Inches Length in Feet Length in Yards

MODEL #328 EZ Tach +PLUS

Features:
Versatile instrument can measure RPM on a wide variety of engines from string trimmers to automotive. Reads engine revolutions from 0 to 20,000 RPM #325 FOR Picks up RPM signal wireless or with supplied AUTOMOTIVE inductive pickup USE - ALL OTHER Great for setting idle speeds! ENGINES, SEE Built-in LED Flashlight which can be used while MODEL #321 & #328 taking measurements Backlit LCD display MODEL #321 VERSA-TACH DIGITAL Accuracy +10 RPM

SMALL ENGINE TACHOMETER

Features:
Great for measuring RPM on outboard, snowmobile, personal watercraft, small engine, motorcycle, industrial and automotive engines. RPM Testing Ranges; 0-10,000 RPM (1 RPM resolution) 0-20,000 RPM (10 RPM resolution) Spark Indicator, can check misfires Peak RPM Hold, captures max RPM Auto power off, two minutes after no signal input Engines Tested: 4 cycle 2 cycle 2 cycle (2X firing) 2 cycle (3X firing)

DESIGNED FOR USE on all 2 and 4 cycle engines firing up to three times per revolution. An RPM hold switch captures and holds the max engine speed. A spark indicator LED indicates the presence of secondary coil output and will detect misfire. Inductive pick-up, instructions and (4)AAA batteries included. Carrying case, 10 foot inductive pick-up and 20 foot inductive pick-up are optional equipment.

GO WITH

FOR QUALITY TEST INSTRUMENTS

ELECTRONIC SPECIALTIES, INC.

MODEL #130 SELF-POWERED INDUCTIVE CLAMP TIMING LIGHT
The original battery powered timing light, built with quality to last. Theres no need to connect to a 12 volt battery for power. Unit is powered by two D cell flashlight batteries. Great tool for marine, snowmobile, industrial, racing engines and other small engine timing. Dont accept a copy. Features:
Accurate up to at least 14,000 RPM For 2 or 4 cycle engines, all ignition systems Protective sleeve withstands high temps (1200F) Available with 10, 20, 30, 40 or 50 ft. lead lengths Standard lead length 4 feet Bright flash at all speeds Batteries included

MODEL #112 ADVANCE INDUCTIVE PICK-UP TIMING LIGHT

Chrome timing light built for heavy duty use. The timing advance function allows precise tuning and diagnostic work. Its subsantial construction allows you to REALLY use this tool. Features:
Xenon flash tube & focused fresnel lens combines for brilliant flash Measures ignition spark advance from 0-70 degrees 12 volt DC operation - reverse polarity protection Accurate up to 8,000 RPM - Removable/replaceable lead set Field replaceable flash tube

MODEL #150 INDUCTIVE PICK-UP TIMING LIGHT

Hard working timing light accurate up to 8,000 RPM. Bright flash. Break and shock resistant housing. Features:

Precision focused flash tube Removable/replaceable leads For all 12V systems Field replaceable flash tube Trigger switch prolongs tube and circuit life

MODEL #120 SELF-POWERED TIMING LIGHT ECONOMY MODEL

Like the #130, this one is entirely self-powered by two D cell batteries. A self-powered timing light can be a convenient tool when 12V vehicle batteries are not accessible. Features:
Very handy in checking for no spark conditions Lightweight design is ideal for field or shop use Built-in flashlight, convenient for dark engine compartments Works on 2 or 4 cycle engines, all ignitions systems Xenon flash tube generates bright flash

#125 DIGITAL TACH/ADVANCE TIMING LIGHT

Professional Timing Light with High Visibility LED display Very bright display indicates: Tach (RPM) Degrees Advance Measures ignition spark advance from 0-90 degrees 2 & 4 Stroke Tachometer measures engine speed up to 9,999 RPM Brilliant Xenon flash at all speeds Detachable & replaceable cable set Designed for precise tuning and diagnostic work Accurate up to 9,000 RPM Works with 12 Volt electrical systems

MODEL #162 DIGITAL TIRE PRESSURE GUAGE

Digital tire pressure readings! Reads in PSI, KPa & Bar Backlit LCD display Built-in LED Flashlight Res: 0.1 PSI - 0.01 Bar - 1 KPa Measurement range: - 5 to 100 PSI - 0.4 to 6.80 Bar - 35 to 680 KPa Uses (2) AAA Batteries

GO WITH

FOR QUALITY TEST INSTRUMENTS

10 NEW PRODUCTS IN THIS CATALOG:

Look for this symbol to locate them
NEW PRODUCT!

PROFESSIONAL HAND HELD TEST EQUIPMENT

Electronic Specialties, Incorporated

2013
Distributed By:

- Since 1967 -

For Automotive, Marine, Small Engine, HVAC & Industrial Technicians

WARRANTY: Each item is covered by a one year limited warranty. Any ES brand product that fails during the first 12 months of use due to faulty material or workmanship will be replaced or repaired at our discretion, free of charge. See price list for complete details on warranty procedures.
Member

Contact Information: Electronic Specialties, Inc. 139 Elizabeth Ln. Genoa City, WI 53128 800-227-1603 262-279-1400 Fax 262-279-1300 internet: www.esitest.com email: [email protected]

WWW.ESITEST.COM