Journal of Hazardous Materials 140 (2007) 173179

Modification of bentonite with a cationic surfactant: An adsorption study of textile dye Reactive Blue 19
Adnan Ozcan
a

a,

Cigdem Omero

glu

, Yunus Erdogan

, A. Safa Ozcan

Department of Chemistry, Faculty of Science, Anadolu University, Yunusemre Campus, 26470 Eskisehir, Turkey b Department of Chemistry, Faculty of Arts and Science, Dumlupinar University, Kutahya, Turkey Received 28 March 2006; received in revised form 16 June 2006; accepted 19 June 2006

Available online 10 July 2006

Abstract The utilization of modified bentonite with a cationic surfactant (dodecyltrimethylammonium (DTMA) bromide) as an adsorbent was successfully carried out to remove a synthetic textile dye (Reactive Blue 19 (RB19)) by adsorption, from aqueous solutions. Batch studies were carried out to address various experimental parameters such as pH, contact time and temperature. The surface modification of bentonite with a surfactant was examined using the FTIR spectroscopic technique and elemental analysis. Effective pH for the adsorption of RB19 onto DTMA bentonite was around 1.5. The Langmuir isotherm model was found to be the best to represent the equilibrium with experimental data. The maximum adsorption capacity (qmax) has been found to be 3.3010 4 molg 1 or 206.58mgg 1. The thermodynamic study indicated that the adsorption of RB19 onto DTMAbentonite was favored with the negative Gibbs free energy values. The pseudo-second-order rate equation was able to provide the best description of adsorption kinetics and the intraparticle diffusion model was also applicable up to 40min for the adsorption of RB19 onto DTMAbentonite. 2006 Elsevier B.V. All rights reserved.
Corresponding author. Tel.: +90 222 3350580/5815; fax: +90 222 3204910. E-mail addresses: [email protected] (A. Ozcan), [email protected] (C. Omero glu), [email protected] (Y. Erdogan), [email protected] (A.S. Ozcan). 0304-3894/$ see front matter 2006 Elsevier B.V. All rights reserved. doi:10.1016 /j.jhazmat. 2006.06.138

Keywords: Bentonite; Organoclay; Adsorption; Reactive dye; Isotherms

1. Introduction Large volumes of colored aqueous effluents are discharged by the various sectors, such as textiles, leather, printing, laundry, tannery, rubber, plastic, painting, etc., industries [1]. The presence of very low concentrations of these effluents are highly visible and undesirable and potentially inhibiting photosynthesis.Owingtotheirchemicalstructure,dyesareresistan ttofading when exposed to light, water and chemicals [2]. Reactive dyes are the most widely used dyes in the textile industry. These types of dyes are colored compounds that have highly soluble in water and have reactive groups which are able to form covalent bonds between dye and fiber [3]. Untreated disposal of this colored water into receiving water body causes damage to aquatic life and also it severe damages to the human bodies [46].

The removal of color from dye-house wastewater is currently one of the major problems faced by the textile dyeing industry. Various physical, chemical and biological treatment methods have been used for the treatment of these textile effluents.However,thesemethodshavecertaindisadvantagessuch as high capital cost and operational costs or secondary sludge disposal problems. Instead of these methods, the adsorption technique can be applied to remove these kinds of textile effluents. Adsorption offers significant advantages over traditional treatment methods especially environmental point of view [713]. Although activated carbonis widely usedasan adsorbentfordye removal from colored waters owing to its excellent adsorption abilities, itishighprice,whichlimitstheirusage[14,15].Hence, alternative low-cost, novel, locally available adsorbents are currently used for the removal of textile dye effluents from aqueous

174

A. Ozcan et al. / Journal of Hazardous Materials 140 (2007) 173179

solutions,insteadofactivatedcarbon.Forinstance,clayssuchas sepiolite [5,6,8,16], zeolite [1720], montmorillonite [2123], smectite [2426] and bentonite [14,15,27,28] can be used in these respects. One of the clay minerals, which is namely bentonite, is composed of units made up of two silica tetrahedral sheets with a central Al octahedral sheet. It has permanent negative charges that increase owing to the isomorphous substitution of Al3+ for Si4+ in the tetrahedral layer and Mg2+ for Al3+ in the octahedral layer. This negative charge is balanced by the presence of exchangeable cations (Na+, Ca2+, etc.) in the lattice structure. Acid and reactive dyes are water soluble anionic dyes are negatively charged and are used to dye textile fibres. Due to the fact that the anionic dyes are negatively charged, the surface of the natural clays has to be modified by a cationic surfactant for the dye adsorption experiments. By the ion-exchange mechanism, the inorganic cation could be exchanged by the organic surfactant cation. Thus, this modification is termed as organoclay and the introduction of organic cation changes the clay from hydrophilic to hydrophobic form. As a result, the adsorption capacity of organoclay increases to compare with natural lay mineralanditcanbeusedasanadsorbentfortheadsorption of dyes [15,29,30]. The characteristics of the dye adsorption behavior are mainly understood in terms of the equilibrium isotherms, thermodynamicparametersandadsorptionkinetics.Theaimofthe present work is to study the adsorption capacity of surfactantmodified bentoniteforadye(ReactiveBlue19,RB19),whichisananionic dye, removal from aqueous solutions. The experimental data for adsorbed RB19 onto surfactant-modified bentonite were compared using two isotherm equations, which are Langmuir and Freundlich.Theequilibriumthermodynamicparametersarealso determined for the RB19 onto surfactant-modified bentonite. Finally, two kinetic models, which are the pseudo-secondorder and intraparticle diffusion, were tested in this study. 2. Materials and methods AcommercialtextiledyeReactiveBlue19(RB19)(Remazol Brilliant Blue R) (C.I. 61200) was provided from Bursa, Turkey and used in all adsorption experiments without further purification. The chemical structure of RB19 is illustrated in Fig. 1. The natural bentonite was obtained from Canakkale, Turkey. It was crushed, ground, sieved through a 63-m sieve, and then dried at 110C in a laboratory oven for 2h prior to use. Bentonite was characterized with respect to cation exchange capacity (CEC), by ammonium acetate method and the surface areabyusingsurfaceareaanalyzerandN2 gaswasusedasadsorbate. Dodecyltrimethylammonium (DTMA) bromide was used as a cationic surfactant for the dye adsorption experiments. The Na-exchanged form of bentonite

and DTMA modified bentonite were prepared according to the literature [15].

Fig. 1. Chemical structure of RB19.

The chemical analysis of natural bentonite was carried out by using an energy dispersive X-ray spectrometer ( EDXLINK ISIS 300) attached to a scanning electron microscope (SEMCam Scan S4). FTIR spectra for Nabentonite and DTMAbentonite were recorded(KBr)onaJascoFT/IR-300EModelFouriertransform infrared spectrometer to confirm the surface modification. The elemental analysis (Vario EL III Elemental Analyzer, Hanau, Germany) was performed to determine C/N ratio in DTMAbentonite. The pH of each solution was measured by using a laboratory scale pH meter (Fisher Accumet AB15) and the absorbance measurements were carried out on UVvis spectrophotometer (Shimadzu UV-2101PC) at the respective max value (592 nm for RB19). Adsorption experiments with DTMAbentonite were performed by batch technique at 20, 30 and 40 C temperatures. A series of 100ml Erlenmeyer flasks containing 50 ml of adsorbate solutions of various concentrations ((2.004.50) 104 moldm3) and required amount of DTMAbentonite were employed at a desired pH by adding a small amount of HCl or NaOH solutions and temperature. These flasks were closed with parafilm to avoid evaporation and then were stirred using a mechanical magnetic stirrer for 60min to achieve equilibration, however, stirring for extra 2h gave practically the same uptake in each case. Once the equilibrium is through to be reached, solution was carefully filtered and concentration of the dye in the solution after equilibrium adsorption was determined spectrophotometricallybymeasuringtheabsorbance.Thewavele ngth was recorded before and after the adsorption and in all the cases no shift in the absorbance peak (max =592nm) was observed. For kinetic studies 50ml solution of RB19 of 2.00 104 moldm3 concentration and 0.030g of adsorbent were taken in a 100ml Erlenmeyer flask. Keeping flask in a water bath, maintained at desired temperature, mixture was mechanically stirred. After a definite interval of time, the solution in the flask was filtered and filtrate of each was analyzed for the uptake of dye.

A. Ozcan et al. / Journal of Hazardous Materials 140 (2007) 173179

175

3. Results and discussion 3.1. Chemical composition of bentonite The chemical composition and surface area of bentonite and DTMAbentonite are given in Table 1. As it can be easily seen from Table 1, the major constituents in bentonite are silica and alumina and the impurities are potassium, calcium, magnesium, iron, titanium and sodium oxides. XRD results combined with EDX analysis indicate that most of the aluminum is in the form of bentonite. XRD also indicated the presence of free quartz in bentonite. As a result, it is expected that the adsorbate species will be removed mainly by silica or alumina. The ratio of C/N for modified-bentonite was obtained from elemental analysis results is 12.61 and the calculated value of C/N ratio for DTMA is 12.86 and the percentage of DTMA onto bentonite is 16.07. These results confirm that the interTable 1 Chemical composition of bentonite Constituents SiO2 Percentage (%) 70.75 Cation exchange capacity (CEC) 145.74mequiv./ 100g Specific surface area N2 atmosphere (m2 g1) Bentonite: 35.09 ; DTMAbentonite: 32.86

3.2. Adsorption dynamics Adsorption of RB19 onto DTMAbentonite was carried out fortheexaminationoftheeffectofpHatarangeof19anditwas found that the adsorption decreased with an increase in pH; as it can be seen from Fig. 3. The variation in the removal of RB19 with respect to pH can be explained by considering the surface charge of the adsorbent. The higher adsorption capacity of the dye onto DTMAbentonite at low pH values may be due to neutralization of the negative charge at its surface as SO3 anion, which increases the protonation and the other words, increas-

Fig. 2. FTIR spectra of natural bentonite and DTMAbentonite.

Al2O3 K2O CaO MgO Fe2O3 TiO2 Na2O Loss of ignition

16.18 2.12 1.62 1.25 0.70 0.18 0.11 6.63

calation of DTMA molecules between the bentonite layers occurs. FTIR spectra of natural bentonite and DTMAbentonite are depicted in Fig. 2. A pair of strong bands at 2856 and 2929cm1 was only observed DTMAbentonite. They can be assigned to the symmetric and asymmetric stretching vibrations of the methyl and methylene groups and their bending vibrations are between 1396 and 1486cm1, supporting the intercalation of DTMA molecules between the silica layers, but these stretching and bending bands are not observed in the natural bentonite. This may be acceptable evidence for the surface modification occurring on bentonite. The band intensities were decreased with surfactant modification of bentonite around at 3400cm1 (stretching band of the OH groups) and at 1600cm1 (related to zeolitic water) (see Fig. 2). This is also the evidence for the modification of bentonite with surfactant (DTMA). At the same time, all above FTIR results are consistent with elemental analysis results.

Fig. 3. pH effect for the adsorption of RB19 onto DTMAbentonite at 20C.

ing the electrostatic attraction between the negatively charged SO3 anion and the positively charged adsorption site. The reason for the high adsorption capacity at low pH is due to the strong electrostatic interaction between the cationic surfactant head groups and dye anions. Decrease in the dye adsorption capacity with increasing pH maybeduetothepositivechargeontheoxideorsolutionsurface appears negatively charged OH ions and the facilities leads to ionic repulsion between the negatively charged surface and the anionic dye molecules. At higher pH values are also not exchangeable anions on the outer surface of the adsorbent and consequently the adsorption capacity decreases. The maximum adsorption capacity of the RB19 takes place at around acidic pH 1.5, which was therefore selected for all further adsorption experiments.

176

A. Ozcan et al. / Journal of Hazardous Materials 140 (2007) 173179

Fig. 4 shows the removal of RB19 by DTMAbentonite at variousadsorbentdoses(0.0150.040g)forthevolumeof50ml, at the dye concentration 2.00104 moldm3. It is evident from the figure that as the amount of adsorbent dosage increases up to 0.030g, the maximum dye removal was attained with this amount and it was used for further experiments. The adsorption capacity of RB19 removed by DTMA bentonite versus contact time is illustrated in Fig. 5. It can be seen from this figure that the adsorption capacity of RB19 ions

(2)) [32] adsorption isotherm models: Langmuir equation: (1)

Freundlich equation:
e

(2)

Fig. 4. The effect of adsorbent doses for the adsorption of RB19 onto DTMA bentonite at 20C.

where qe is the equilibrium dye concentration on the adsorbent (molg1), Ce the equilibrium dye concentration in solution (moldm3), qmax the monolayer capacity of the adsorbent (molg1), KL the Langmuir constant (dm3 mol1) and related to the free energy of adsorption, KF the Freundlich constant (dm3 g1) and n (dimensionless) is the heterogeneity factor. Best-fitted straight lines with high correlation coefficients obtained in case of Langmuir (Fig. 6) and Freundlich (Fig. 7). The all isotherm parameters derived from the respective plots are presented in Table 2. The fit of the data for RB19 adsorption onto DTMAbentonite suggests that the Langmuir model gave slightly better fitting than that of Freundlich model, as it is obvious from a comparison of the r2 values in Table 2. It is also evident from these data that the surface of DTMAbentonite is made up of homogenous adsorption patches than heterogeneous adsorption patches.

Fig. 5. Effect of contact time for the adsorption of RB19 onto DTMA bentonite at various temperatures.

increased with contact time up to 40min after that a maximum removal is attained. For this reason, the optimum contact time was selected as 40 min. The equilibrium adsorption capacity of RB19 onto DTMA bentonite decreases with increasing temperature (Fig. 5), which indicatesthattheadsorptionofRB19incontrolledbyanexothermic and physical adsorption process and due to a weakening of the attractive forces between RB19 and DTMAbentonite sites. Adsorption data obtained in the concentration range (2.00 4.50) 104 moldm3 were correlated with the following linear forms of Langmuir (Eq. (1)) [31] and Freundlich ( Eq.

Fig. 6. Langmuir plots for the adsorption of RB19 onto DTMAbentonite at various temperatures.

A. Ozcan et al. / Journal of Hazardous Materials 140 (2007) 173179

177

this implies that adsorption process is chemical, but a value for n is above to unity, adsorption is favorable a physical process. The highest value of n at equilibrium is 4.946 at 20C, represents favorable adsorption at low temperature, and therefore this would seem to suggest that physical, which is referred the adsorption bond becomes weak and conducted with van der Waals forces, rather than chemical adsorption is dominant when it is used for adsorbing RB19. Langmuir constant KL can be used for calculating thermodynamic parameters, such as the change in free energy ( ), enthalpy ( ) and entropy ( ), which are associated to the adsorption process, on the basis of the following equations:
Fig. 7. Freundlich plots for the adsorption of RB19 onto DTMAbentonite at various temperatures.
L

(4) (5)

The favorability of the adsorption process was confirmed by using a basic method applied by Weber and Chakravorti [33], whichsuggeststhatthelinear,favorableorunfavorablenatureof isotherm is dependent on the obtained value of separation factor (RL) as unity, between 01 and zero, respectively. The separation factor RL, a dimensionless constant, can be calculated by

Table 2 Adsorption isotherm parameters for RB19 onto DTMAbentonite t (C) 20 Langmuir qmax (molg1) KL ( dm 3 mol1) rL 2 RL Freundlich n K F ( dm 3 g1) 3.30104 2.89104 0.995 7.14102 4.946 1.56103 0.958

the

adsorption of

The plot of lnKL as a function of 1/T (Fig. 8) yields a straight line from which H and S were calculated from the slope and intercept, respectively. The results of thermodynamic parameters are given in Table 3. The change of free energy for physisorption is usually between 20 and kJmol 1 0 , whereas chemisorption is a range of 80 to kJmol 1 400 valuesforthetemperaturesatarangeof2040Cwereobtained between25.04and26.43kJmol1,whichindicatethenature of adsorption spontaneous. These values were in the middle of physisorptionandchemisorption.Itmaybeconcludedthatthisis

30

40

3.15104 2.72104 0.995 7.56102 4.896 1.51103 0.947

2.98104 2.57104 0.982 7.97102 4.793 1.46103 0.971

following equation: (3) where KL is the Langmuir constant (dm3 mol1) and C0 is the highest initial dye concentration (moldm3). The values of RL calculated as above equation (Table 2) were found less than unity at all studied temperatures, and therefore the adsorption of RB19 onto DTMAbentonite is especially favorable at all studied temperatures. The Freundlich constant n is a measure of the deviation from linearity of the adsorption. If a value for n is equal to unity the adsorption is linear. If a value for n is below to unity,
Fig. 8. Plot of lnKL vs. 1/T for estimation of thermodynamic parameters for the adsorption of RB19 onto DTMAbentonite. Table 3 Thermodynamic parameters calculated from the Langmuir isotherm constant (KL) for the adsorption of RB19 onto DTMAbentonite t (C) 1 ) (kJmol1)

178

A. Ozcan et al. / Journal of Hazardous Materials 140 (2007) 173179

interpreted a physical adsorption enhanced by a chemical effect [35]. The negative value of the 4.55kJmol1) indicates that the adsorption is exothermic and the value of implies thatadsorptionisalsophysicalinnatureinvolvingweakforcesof attraction. The positive value of (+69.88Jmol1 K1) corresponds to an increase in the degree of freedom of the adsorbed species. 3.3. Kinetic studies The kinetics of adsorption data was evaluated to understand the mechanism of adsorption process by means of the pseudosecond-order kinetic and intraparticle diffusion models. The pseudo-second-order kinetic model equation [36] can be written as follows: (6) The intraparticle diffusion equation [37] is expressed as: qt = kpt1/2 + C (7)

Fig. 10. Intraparticle diffusion plots for the adsorption of RB19 onto DTMA bentonite at various temperatures.

where q2 and qt are the amounts of the dye adsorbed at equilibrium and at time t, in molg1, k2 the equilibrium rate constant of the pseudo-second-order model for the adsorption process (gmol1 min1), C the intercept and kp is the intraparticle diffusionrateconstant(molg1 min1/2) .Thestraight-lineplotsof t/qt versus t for the pseudo-secondorder (Fig. 9) and qt against t1/2 for the intraparticle diffusion (Fig. 10) for the adsorption of RB19 onto DTMAbentonite have been also examined to obtain the rate parameters. All of kinetic data of RB19 under different conditions were calculated from these plots and are

listed in Table 4. From this table, the maximum adsorption capacities (q2) at equilibrium are decreased from (2.16 to 2.01) 104 molg1 for RB19 when the temperature is increased from 20 to 40C for DTMAbentonite. This effect can be interpreted as assuming that a higher temperatures the total energy of the adsorbate molecules is increased and then their escaping tendency is also increased, thus, the adsorption of the adsorbate species is decreased. As a result, the adsorption process in this study favors a low temperature physical adsorption mechanism and to depend on the temperature [15,38]. The pseudo-second-order rate constants for RB19 onto DTMA bentoniteshowasteadyincreasewithsolutiontemperature(Table4 ).Ingenerally,duringaphysicaladsorptionprocess, increasing temperature leads to increase the rate of approach to equilibrium, whereas decreases the equilibrium adsorption capacity [36]. As discussed above, the validity of the pseudo-second-order kinetic and intraparticle diffusion models can be quantitatively checked by using a normalized standard deviation (%) calculated by the following equation [39]: 100 (8)

Table 4 Kinetic parameters and the normalized standard deviations for the adsorption of RB19 onto DTMAbentonite at various temperatures t (C) 20 Pseudo-second-order Fig. 9. Pseudo-second-order kinetic plots for the adsorption of RB19 onto DTMAbentonite at various temperatures. k2 (gmol1 min1) q2 (molg1) (%) 3.60103 2.16104 1.804 0.999 Intraparticle diffusion 5.65103 2.10104 1.951 0.999 1.15103 2.01104 0.598 0.999 30 40

A. Ozcan et al. / Journal of Hazardous Materials 140 (2007) 173179

179

kp (molg1 min1/2)

5.02106 4.80106 3.85106

where n is the number of data points and the calculated results are given in Table 4. According to Table 4, the values of q for the best-fitted model are less than 1.952%. It is concluded that the adsorption of RB19 onto DTMAbentonite can be best described by the pseudo-second-order kinetic model. 4. Conclusions The research was carried out in this paper clearly suggests that surfactant-modified bentonite acts a well adsorbent for the removal of Reactive Blue 19 (RB19) from aqueous solutions. The surface modification of bentonite was tested by using the FTIR technique and elemental analysis. Batch studies suggest the (3.30 10 4 molg 1 that high adsorption capacity or 206.58mgg 1) of DTMAbentonite in acidic solutions ( pH around1.5)isduetothestrongelectrostaticinteractionsbetween its adsorption site and dye anion. The straight lines obtained for the Langmuir and Freundlich models obey to fit well with the experimental equilibrium data but the Langmuir model gives slightly better fitting than Freundlich model. The thermodynamic parameters obtained from Langmuir constant (KL) indicate a feasible, spontaneous and exothermic adsorption. A pseudo-second-order kinetic and intraparticle diffusion models have been applied to predict the rate constants of adsorption and equilibrium adsorption capacities. References
[1] V.K.C. Lee, J.F. Porter, G. McKay, Fixed-bed modeling for acid dye adsorption onto activated carbon, J. Chem. Technol. Biotechnol. 78 (2003) 12811289. [2] S.W.Won,S.B.Choi,Y.-S.Yun,Performanceandmechanisminbindingof Reactive Orange 16 to various types of sludge, Biochem. Eng. J. 28 (2006) 208214. [3] T.N.D.C. Dantas, L.T.C. Beltrame, A.A.D. Neto, C.P.D.A. Moura, Use of microemulsions for removal of color and dyes from textile wastewater, J. Chem. Technol. Biotechnol. 79 (2004) 645650. [4] P. Baskaralingam, M. Pulikesi, D. Elango, V. Ramamurthi, S. Sivanesan, Adsorption of acid dye onto organobentonite, J. Hazard. Mater. 128 (2006) 138144. [5] A. Ozcan, E.M. Onc u, A.S. Ozcan, Kinetics, isotherm and thermodynamic studies of adsorption of Acid Blue 193 from aqueous solutions onto natural sepiolite, Colloids Surf. A: Physicochem. Eng. Aspects 277 (2006) 9097. [6] A. Ozcan, E.M. Onc u, A.S. Ozcan, Adsorption of Acid Blue 193 from aqueous solutions onto DEDMA-sepiolite, J. Hazard. Mater. 129 (2006) 244252. [7] K. Ravikumar, B. Deebika, K. Balu, Decolourization of aqueous dye solutions by a novel adsorbent: application of statistical designs and surface plots for the optimization and regression analysis, J. Hazard. Mater. 122 (2005) 7583.

[8] K. Ravikumar, K. Pakshirajan, T. Swaminathan, K. Balu, Optimization of batch process parameters using response surface methodology for dye removal by a novel adsorbent, Chem. Eng. J. 105 (2005) 131138. [9] V.K. Gupta, I. Ali, Suhas, D. Mohan, Equilibrium uptake and sorption dynamics for the removal of a basic dye (basic red) using low-cost adsorbents, J. Colloid Interf. Sci. 265 (2003) 257264. [10] V.K. Gupta, A. Mittal, L. Krishnan, V. Gajbe, Adsorption kinetics and column operations for the removal and recovery of malachite green from wastewater using bottom ash, Sep. Purif. Technol. 40 (2004) 87 96. [11] A. Mittal, L. Kurup Krishnan, V.K. Gupta, Use of waste materialsbottom ash and de-oiled soya, as potential adsorbents for the removal of amaranth from aqueous solutions, J. Hazard. Mater. 117 (2005) 171 178. [12] A. Mittal, Use of hen feathers as potential adsorbent for the removal of a hazardous dye, Brilliant Blue FCF, from wastewater, J. Hazard. Mater. 128 (2006) 233239. [13] K.G.Bhattacharyya,A.Sharma,Azadirachtaindicaleafpowderasaneffective biosorbent for dyes: a case study with aqueous Congo Red solutions, J. Environ. Manage. 71 (2004) 217229. [14] A.S. Ozcan, B. Erdem, A. Ozcan, Adsorption of Acid Blue 193 from aqueous solutions onto BTMAbentonite, Colloids Surf. A: Physicochem. Eng. Aspects 266 (2005) 7381. [15] A.S. Ozcan, B. Erdem, A. Ozcan, Adsorption of Acid Blue 193 from aqueous solutions onto Nabentonite and DTMAbentonite, J. Colloid Interf. Sci. 280 (2004) 4454. [16] A.S. Ozcan, S. Tetik, A. Ozcan, Adsorption of acid dyes from aqueous solutions onto sepiolite, Sep. Sci. Technol. 39 (2004) 301320. [17] B. Armagan, O. Ozdemir, M. Turan, M.S. Celik, The removal of reactive azodyes by natural and modified zeolites, J. Chem. Technol. Biotechnol. 78 (2003) 725732. [18] B. Armagan, M. Turan, M.S. Celik, Equilibrium studies on the adsorption of reactive azodyes into zeolite, Desalination 170 (2004) 33 39. [19] Y.E.Benkli,M.F.Can,M.Turan,M.S.Celik,Modificationoforganozeolite surfacefortheremovalofreactiveazodyesinfixed-bedreactors,WaterRes. 39 (2005) 487493. [20] S. Wang, H. Li, L. Xu, Application of zeolite MCM-22 for basic dye removal from wastewater, J. Colloid Interf. Sci. 295 (2006) 71 78. [21] C.-C. Wang, L.-C. Juang, T.-C. Hsu, C.-K. Lee, J.-F. Lee, F.-C. Huang, Adsorption of basic dyes onto montmorillonite, J. Colloid Interf. Sci. 273 (2004) 8086. [22] R. Wibulswas, Batch and fixed bed sorption of methylene blue on precursor and QACs modified montmorillonite, Sep. Purif. Technol. 39 (2004) 312. [23] T. Polubesova, M. Epstein, S. Yariv, I. Lapides, S. Nir, Adsorption of alizarinate-micelle complexes on Na-montmorillonite, Appl. Clay Sci. 24 (2004) 177183. [24] M. Ogawa, R. Kawai, K. Kuroda, Adsorption and aggregation of a cationic cyanine dye on smectites, J. Phys. Chem. (US) 100 (1996) 1621816221. [25] F.L. Arbeloa, J.M. Herran Martinez, T.L. Arbeloa, I.L. Arbeloa, Hydrophobic effect on the adsorption of rhodamines in aqueous suspensions of smectites. The rhodamine 3B/Laponite B system, Langmuir 14 (1998) 45664573. [26] A. Czmerova, J. Bujdak, A. Gaplovsk y, The aggregation of thionine and methylene blue dye in smectite dispersion, Colloids Surf. A: Physicochem. Eng. Aspects 243 (2004) 8996. [27] Q.H. Hu, S.Z. Qiao, F. Haghseresht, M.A. Wilson, G.Q. Lu, Adsorption study for removal of basic red dye using bentonite, Ind. Eng. Chem. Res. 45 (2006) 733738. [28] S. Al-Asheh, F. Banat, L. Abu-Aitah, The removal of methylene blue dye from aqueous solutions using activated and non-activated bentonites, Ads. Sci. Technol. 21 (2003) 451462. [29] Y.-H. Shen, Preparation of organobentonite using non-ionic surfactants, Chemosphere 44 (2001) 989995.

180

A. Ozcan et al. / Journal of Hazardous Materials 140 (2007) 173179

[30] G. Sheng, S. Xu, S.A. Boyd, Cosorption of organic contaminants from water by hexadecyltrimethylammonium-exchanged clays, Water Res. 30 (1996) 14831489. [31] I. Langmuir, The adsorption of gases on plane surfaces of glass, mica and platinum, J. Am. Chem. Soc. 40 (1918) 13611403. [32] H.M.F. Freundlich, Uber die adsorption in losungen, Z. Phys. Chem. 57 (1906) 385470. [33] T.W. Weber, R.K. Chakravorti, Pore and solid diffusion models for fixedbed adsorbers, J. Am. Inst. Chem. Eng. 20 (1974) 228238. [34] M.J. Jaycock, G.D. Parfitt, Chemistry of Interfaces, Ellis Horwood Ltd., Onichester, 1981. [35] Y. Yu, Y.-Y. Zhuang, Z.-H. Wangy, Adsorption of water-soluble dye onto functionalized resin, J. Colloid Interf. Sci. 242 (2001) 288293. [36] Y.S. Ho, G. McKay, Sorption of dye from aqueous solution by peat, Chem. Eng. J. 70 (1998) 115124. [37] W.J.WeberJr.,J.C.Morriss,Kineticsofadsorptiononcarbonfromsolution, J. Sanitary Eng. Div. Am. Soc. Civil Eng. 89 (1963) 3160. [38] Y.S. Ho, G. McKay, Kinetic models for the sorption of dye from aqueous solution by wood, Process Saf. Environ. Protect. 76 (1998) 183 191. [39] F.-C. Wu, R.-L. Tseng, R.-S. Juang, Kinetic modeling of liquid-phase adsorption of reactive dyes and metal ions on chitosan, Water Res. 35 (2001) 613618.