MAINTENANCE

Outboard Care
To keep your outboard in the best operating condition, it is important that your outboard receive the periodic inspections and maintenance listed in the Inspection and Maintenance Schedule. We urge you to keep it maintained properly to ensure the safety of you and your passengers, and retain its dependability.

! WARNING
Neglected inspection and maintenance service of your outboard or attempting to perform maintenance or repair on your outboard if you are not familiar with the correct service and safety procedures could cause personal injury, death, or product failure. Record maintenance performed in Maintenance Log at the back of this book. Save all maintenance work orders and receipts.

SELECTING REPLACEMENT PARTS FOR YOUR OUTBOARD

We recommend using original Mercury Precision or Quicksilver replacement parts and Genuine Lubricants.

! WARNING
Using a replacement part that is inferior to the original part could result in personal injury, death, or product failure.

EPA Emissions Regulations

All new outboards manufactured by Mercury Marine are certified to the United States Environmental Protection Agency, as conforming to the requirements of the regulations for the control of air pollution from new outboard motors. This certification is contingent on certain adjustments set to factory standards. For this reason, the factory procedure for servicing the product must be strictly followed and, wherever practicable, returned to the original intent of the design. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any marine spark ignition (SI) engine repair establishment or individual.

61

MAINTENANCE
EMISSION CERTIFICATION LABEL
An emission certification label, showing emission levels and engine specifications directly related to emissions, is placed on the engine at time of manufacture.

a b c d e

f g h i
ob00366

abcde-

Idle speed Engine horsepower Piston displacement Date of manufacture Valve clearance (if applicable)

f - Family number g - Maximum emission output for the engine family h - Timing specification i - Recommended spark plug and gap

OWNER RESPONSIBILITY
The owner/operator is required to have routine engine maintenance performed to maintain emission levels within prescribed certification standards. The owner/operator is not to modify the engine in any manner that would alter the horsepower or allow emissions levels to exceed their predetermined factory specifications.

Inspection And Maintenance Schedule

BEFORE EACH USE
Check engine oil level. See Fuel & Oil Checking and Adding Engine Oil. Check that lanyard stop switch stops the engine. Visually inspect the fuel system for deterioration or leaks. Check outboard for tightness on transom. Check steering system for binding or loose components. 62

MAINTENANCE
Remote Control Models Visually check steering link rod fasteners for proper tightness. See Steering Link Rod Fasteners. Check propeller blades for damage. Flush out the outboard cooling system if operating in salt or polluted water. See Flushing the Cooling System. Wash off all salt deposits and flush out the exhaust outlet of the propeller and gearcase with fresh water if operating in salt water.

AFTER EACH USE

EVERY 100 HOURS OF USE OR ONCE YEARLY, WHICHEVER OCCURS FIRST

Lubricate all lubrication points. Lubricate more frequently when used in salt water. See Lubrication Points. Change engine oil and replace the oil filter. The oil should be changed more often when the engine is operated under adverse conditions such as extended trolling. See Changing Engine Oil. Replace spark plugs at first 100 hours or first year. After that, inspect spark plugs every 100 hours or once yearly. Replace spark plugs as needed. See Spark Plug Inspection and Replacement. Inspect thermostat visually for corrosion and broken spring. Make sure thermostat closes completely at room temperature.1. Check fuel line filter for contaminants. See Fuel System. Check corrosion control anodes. Check more frequently when used in salt water. See Corrosion Control Anode. Check and adjust valve clearance, if necessary.1. Drain and replace gearcase lubricant. See Gearcase Lubrication. Lubricate splines on the driveshaft.1. Remote control models Check control cable adjustments. 1. Inspect timing belt. See Timing Belt Inspection. Check tightness of bolts, nuts, and other fasteners. Replace water pump impeller (more often if overheating occurs or reduced water pressure is noted).1. Refer to Storage procedure. See Storage section.

EVERY 300 HOURS OF USE OR THREE YEARS

BEFORE PERIODS OF STORAGE

1. These items should be serviced by an authorized dealer.

63

MAINTENANCE
Flushing The Cooling System Standard Models
Flush the internal water passages of the outboard with fresh water after each use in salt, polluted, or muddy water. This will help prevent a buildup of deposits from clogging the internal water passages. Use a Mercury Precision or Quicksilver accessory (or equivalent) flushing attachment. IMPORTANT: The engine must be run during flushing in order to open the thermostat and circulate water through the water passages.

! WARNING
To avoid possible injury when flushing, remove the propeller. Refer to Propeller Replacement. 1. Remove propeller. Refer to Propeller Replacement. Install the flushing attachment so the rubber cup fits tightly over the cooling water intake. 2. Attach a water hose to the flushing attachment. Turn on the water and adjust the flow so water is leaking around the rubber cup to ensure the engine receives an adequate supply of cooling water.

ob00567

3. Start the engine and run it at idle speed in neutral shift position. IMPORTANT: Do not run engine above idle when flushing. 4. Adjust water flow (if necessary) so excess water continues leaking out from around the rubber cup to ensure the engine is receiving an adequate supply of cooling water.

ob00568

64

MAINTENANCE
5. Check for a steady stream of water flowing out of the water pump indicator hole. Continue flushing the outboard for 3 to 5 minutes, carefully monitoring water supply at all times. 6. Stop the engine, turn off the water, and remove the flushing attachment. Reinstall the propeller.

Flushing The Cooling System Bigfoot Models

Flush the internal water passages of the outboard with fresh water after each use in salt, polluted, or muddy water. This will help prevent a buildup of deposits from clogging the internal water passages. Use a Mercury Precision or Quicksilver accessory (or equivalent) flushing attachment. IMPORTANT: The engine must be run during flushing in order to open the thermostat and circulate water through the water passages.

! WARNING
To avoid possible injury when flushing, remove the propeller. Refer to Propeller Replacement. 1. Remove propeller. Refer to Propeller Replacement. Install the flushing attachment so the rubber cups fit tightly over the cooling water intake.

ob00569

2. Attach a water hose to the flushing attachment. Turn on the water and adjust the flow so water is leaking around the rubber cups to ensure the engine receives an adequate supply of cooling water.

ob00570

3. Start the engine and run it at idle speed in neutral shift position. IMPORTANT: Do not run engine above idle when flushing.

65

MAINTENANCE
4. Adjust water flow (if necessary) so excess water continues leaking out from around the rubber cups to ensure the engine is receiving an adequate supply of cooling water.

ob00571

5. Check for a steady stream of water flowing out of the water pump indicator hole. Continue flushing the outboard for 3 to 5 minutes, carefully monitoring water supply at all times. 6. Stop the engine, turn off the water, and remove the flushing attachment. Reinstall the propeller.

Top Cowl Removal And Installation

REMOVAL
1. Unlock the rear latch by pushing lever down.

ob00368

2. Lift rear of cowl and disengage front hook.

ob00369

INSTALLATION
1. Engage the front hook and push cowl back over the cowl seal. 2. Push cowl down and move the rear latch lever up to lock.

Battery Inspection
The battery should be inspected at periodic intervals to ensure proper engine starting capability. 66

MAINTENANCE
IMPORTANT: Read the safety and maintenance instructions which accompany your battery. 1. Turn off the engine before servicing the battery. 2. Add water as necessary to keep the battery full. 3. Make sure the battery is secure against movement. 4. Battery cable terminals should be clean, tight, and correctly installed. Positive to positive and negative to negative. 5. Make sure the battery is equipped with a nonconductive shield to prevent accidental shorting of battery terminals.

Fuel System
! WARNING
Avoid serious injury or death from gasoline fire or explosion. Carefully follow all fuel system service instructions. Always stop the engine and do not smoke or allow open flames or sparks in the area while servicing any part of the fuel system. Before servicing any part of the fuel system, stop engine and disconnect the battery. Drain the fuel system completely. Use an approved container to collect and store fuel. Wipe up any spillage immediately. Material used to contain spillage must be disposed of in an approved receptacle. Any fuel system service must be performed in a well ventilated area. Inspect any completed service work for signs of fuel leakage.

FUEL LINE INSPECTION

Visually inspect the fuel line and primer bulb for cracks, swelling, leaks, hardness, or other signs of deterioration or damage. If any of these conditions are found, the fuel line or primer bulb must be replaced.

FUEL LINE FILTER

Inspect the fuel line filter. If the filter appears to be contaminated, remove and replace.

ob00574

67

MAINTENANCE
IMPORTANT: Visually inspect for fuel leakage from the filter connections by squeezing the primer bulb until firm, forcing fuel into the filter.

Fuse Replacement Electric Start Models

IMPORTANT: Always carry spare 20 AMP fuses. The electric starting circuit is protected from overload by a 20 AMP fuse. If the fuse is blown try to locate and correct the cause of the overload. If the cause is not found, the fuse may blow again. 1. Open the fuse holder and look at the silver colored band inside the fuse. If band is broken, replace the fuse. Replace fuse with a new fuse with the same rating.

a
a - Good fuse

ob00575

b - Blown fuse

Corrosion Control Anode

Your outboard has a corrosion control anode installed to the gearcase. An anode helps protect the outboard against galvanic corrosion by sacrificing its metal to be slowly corroded instead of the outboard metals.

68

MAINTENANCE
The anode requires periodic inspection especially in salt water which will accelerate the erosion. To maintain this corrosion protection, always replace the anode before it is completely eroded. Never paint or apply a protective coating on the anode as this will reduce effectiveness of the anode.

a b

ob00576

a - Anode Bigfoot

b - Anode Standard

Steering Link Rod Fasteners

IMPORTANT: The steering link rod that connects the steering cable to the engine must be fastened using special washer head bolt ("a" Part Number 10849838) and selflocking nylon insert locknuts ("b" & "d" Part Number 11826709113). These locknuts must never be replaced with common nuts (nonlocking) as they will work loose and vibrate off freeing the link rod to disengage.

69

MAINTENANCE
! WARNING
Disengagement of a steering link rod can result in the boat taking a full, sudden, sharp turn. This potentially violent action can cause occupants to be thrown overboard exposing them to serious injury or death.

b d c

a
ob00577

abcd-

Special washer head bolt (10849838) Nylon insert locknut (11826709113) Flat washer (2) Nylon insert locknut (11826709113)

Assemble steering link rod to steering cable with two flat washers and nylon insert locknut. Tighten locknut until it seats, then back nut off 1/4 turn. Assemble steering link rod to engine with special washer head bolt and locknut. First torque bolt, then torque locknut to specifications.
Description Special washer head bolt Nylon insert locknut "b" Nylon insert locknut "d" Nm 27 27 lb. in. lb. ft. 20 20

Tighten until seats, then back off 1/4 turn

70

MAINTENANCE
Propeller Replacement Standard Models
! WARNING
If the propeller shaft is rotated while the engine is in gear, there is the possibility that the engine will crank over and start. To prevent this type of accidental engine starting and possible serious injury caused from being struck by a rotating propeller, always shift outboard to neutral position and remove spark plug leads when you are servicing the propeller. 1. Shift the outboard to neutral position.

ob00561

2. Remove the spark plug leads to prevent engine from starting.

ob00375

3. Place a block of wood between gearcase and propeller to hold propeller and remove propeller nut.

ob00578

71

MAINTENANCE
4. Pull propeller straight off shaft. If propeller is seized to the shaft and cannot be removed, have the propeller removed by an authorized dealer.

ob00579

5. Coat the propeller shaft with Quicksilver or Mercury Precision Lubricants AntiCorrosion Grease or 24C.
Tube Ref No.
94 95

Description Anti-Corrosion Grease 2-4-C

Where Used Propeller shaft Propeller shaft

Part No. 92-802867A 1 92-802859A 1

ob00580

IMPORTANT: To prevent the propeller hub from corroding and seizing to the propeller shaft (especially in salt water), always apply a coat of the recommended lubricant to the entire propeller shaft at the recommended maintenance intervals and also each time the propeller is removed. 6. FloTorq I Drive Hub Propellers Install forward thrust hub, propeller, rear thrust hub and propeller nut onto the shaft.

a b
a - Propeller nut b - Rear thrust hub

d
ob00581

c - Propeller d - Forward thrust hub

72

MAINTENANCE
7. Place a block of wood between gearcase and propeller and tighten propeller nut.

ob00583

Propeller Replacement Bigfoot Models

! WARNING
If the propeller shaft is rotated while the engine is in gear, there is the possibility that the engine will crank over and start. To prevent this type of accidental engine starting and possible serious injury caused from being struck by a rotating propeller, always shift outboard to neutral position and remove spark plug leads when you are servicing the propeller. 1. Shift the outboard to neutral position.

ob00561

2. Remove the spark plug leads to prevent engine from starting.

d
a - Propeller nut b - Propeller nut retainer c - Thrust hub 73

ob00382

d - Continuity washer e - Propeller f - Thrust washer

MAINTENANCE
3. Place a block of wood between gearcase and propeller to hold propeller and remove propeller nut.

ob00578

4. Pull propeller straight off shaft. If propeller is seized to the shaft and cannot be removed, have the propeller removed by an authorized dealer.

ob00584

5. Coat the propeller shaft with Quicksilver or Mercury Precision Lubricants AntiCorrosion Grease or 24C.
Tube Ref No.
94 95

Description Anti-Corrosion Grease 2-4-C

Where Used Propeller shaft Propeller shaft

Part No. 92-802867A 1 92-802859A 1

ob00585

IMPORTANT: To prevent the propeller hub from corroding and seizing to the propeller shaft (especially in salt water), always apply a coat of the recommended lubricant to the entire propeller shaft at the recommended maintenance intervals and also each time the propeller is removed. 74

MAINTENANCE
6. FloTorq I Drive Hub Propellers Install forward thrust hub, propeller and propeller nut onto the shaft.

a
a - Propeller nut b - Propeller

c
ob00586

c - Forward thrust hub

7. Place a block of wood between gearcase and propeller and tighten propeller

ob00583

Spark Plug Inspection And Replacement

! WARNING
Avoid serious injury or death from fire or explosion caused by damaged spark plug boots. Damaged spark plug boots can emit sparks. Sparks can ignite fuel vapors under the engine cowl. To avoid damaging spark plug boots, do not use any sharp object or metal tool such as pliers, screwdriver, etc. to remove spark plug boots. 1. Remove the spark plug leads. Twist the rubber boots slightly and pull off.

ob00375

75

MAINTENANCE
2. Remove the spark plugs to inspect. Replace spark plug if electrode is worn or the insulator is rough, cracked, broken, blistered or fouled.

ob00423

3. Set the spark plug gap to specifications.

ob00680

Spark Plug Gap Spark plug 0.90 mm (0.035 in.)

4. Before installing spark plugs, clean off any dirt on the spark plug seats. Install plugs finger tight, and then tighten to the specified value.
Description Spark plug Nm 27 lb. in. lb. ft. 20

Timing Belt Inspection

Inspect the timing belt and have it replaced by an authorized dealer if any of the following conditions are found. 1. Cracks in the back of the belt or in the base of the belt teeth. 2. Excessive wear at the roots of the cogs. 3. Rubber portion swollen by oil. 4. Belt surfaces roughened. 5. Signs of wear on edges or outer surfaces of belt.

76

MAINTENANCE
6. Stretching by 10 mm (0.39 in.) or more when belt is pushed in with your finger.

ob00588

Exterior Care
Your outboard is protected with a durable baked enamel finish. Clean and wax often using marine cleaners and waxes.

Changing Engine Oil

ENGINE OIL CAPACITY
Engine oil capacity is approximately 1 liter (1 quart ).

OIL CHANGING PROCEDURE

1. 2. 3. 4. Lock the outboard in the full tilt up position. Position outboard so the drain hole is facing downward. Remove drain plug and drain engine oil into an appropriate container. After the initial oil has been drained, Temporarily reinstall the drain plug. Disengage the tilt lock and lower the outboard. Wait a minute to allow the remaining oil that was trapped in the engine to return to the drain. Return outboard to the full tilt position and drain the remaining oil. 5. Lubricate the seal on the drain plug with oil and reinstall.

ob00590

77

MAINTENANCE
CHANGING OIL FILTER
1. Place a rag or towel below the oil filter to absorb any spilled oil. 2. Unscrew old filter by turning the filter to the left. 3. Clean the mounting base. Apply film of clean oil to filter gasket. Do not use grease. Screw new filter on until gasket contacts base, then tighten 3/4 to 1 turn.

ob00591

OIL FILLING
IMPORTANT: Do not overfill. Be sure that the outboard is upright (not tilted) when checking oil. 1. Remove the oil fill cap and refill with 1liter (1 quart ) of oil. Reinstall the oil fill cap. 2. Idle engine for five minutes and check for leaks. Stop engine and check oil level on dipstick. Add oil if necessary.

Lubrication Points
1. Lubricate the following with Quicksilver or Mercury Precision Lubricants 24C or Special Lubricant 101.
Tube Ref No. Description Where Used Steering friction adjustment shaft, swivel bracket, transom clamp screws, tilt tube, throttle/shift cables, steering cable grease fitting Part No.

34

Special Lubricant 101

92-802865A 1

78

MAINTENANCE
Tube Ref No. Description Where Used Steering friction adjustment shaft, swivel bracket, transom clamp screws, tilt tube, throttle/shift cables, steering cable grease fitting Part No.

95

2-4-C

92-802859A 1

Steering friction adjustment shaft (tiller handle models) Lubricate fitting. Swivel bracket Lubricate through fitting. Transom clamp screws Lubricate threads.

b
c

ob00592

a - Steering friction adjustment shaft b - Transom clamp screw c - Swivel bracket Tilt tube Lubricate through fittings.

ob00593

79

MAINTENANCE
Lubricate the throttle and shift cables, moving components and pivot locations.

ob00594

Steering Cable Grease Fitting (If Equipped) Rotate steering wheel to fully retract the steering cable end into the outboard tilt tube. Lubricate through fitting.

a b
ob00595

a - Steering cable grease fitting b - Steering cable end

! WARNING
The end of the steering cable must be fully retracted into the outboard tilt tube before adding lubricant. Adding lubricant to steering cable when fully extended could cause steering cable to become hydraulically locked. A hydraulically locked steering cable will cause loss of steering control, possibly resulting in serious injury or death. 2. Lubricate the following with Light Weight Oil

80

MAINTENANCE
Steering Link Rod Pivot Points Lubricate pivot points.

a
ob00596

a - Steering link rod pivot points 3. Lubricate the following with Quicksilver Quicksilver or Mercury Precision Lubricants AntiCorrosion Grease or 24C.
Tube Ref No.
94 95

Description Anti-Corrosion Grease 2-4-C

Where Used Propeller shaft Propeller shaft

Part No. 92-802867A 1 92-802859A 1

Propeller Shaft Refer to Propeller Replacement for removal and installation of the propeller. Coat the entire propeller shaft with lubricant to prevent the propeller hub from corroding to the shaft.

ob00585

Gearcase Lubrication
When adding or changing gearcase lubricant, visually check for the presence of water in the lubricant. If water is present, it may have settled to the bottom and will drain out prior to the lubricant, or it may be mixed with the lubricant, giving it a milky colored appearance. If water is noticed, have the gearcase checked by your dealer. Water in the lubricant may result in premature bearing failure or, in freezing temperatures, will turn to ice and damage the gearcase. 81

MAINTENANCE
Remove the fill/drain plug and examine the magnetic end for metal particles. A small amount of metal filings or fine metal particles indicates normal gear wear. An excessive amount of metal filings or larger particles (chips) may indicate abnormal gear wear and should be checked by an authorized dealer.

DRAINING GEARCASE
1. Place outboard in a vertical operating position. 2. Place drain pan below outboard. 3. Remove fill/drain plug and vent plug and drain lubricant.

a
ob00597

a - Fill/drain plug

b - Vent plug

GEARCASE LUBRICANT RECOMMENDATION

Mercury or Quicksilver Premium or High Performance Gear Lubricant.

GEARCASE LUBRICANT CAPACITY

Standard model gearcase: Approximately 200 ml (6.8 fl. oz.). Bigfoot model gearcase: Approximately 260 ml (8.8 fl. oz.)

CHECKING LUBRICANT LEVEL AND REFILLING GEARCASE

1. Place outboard in a vertical operating position. 2. Remove vent plug and fill/drain plug. 3. Remove fill screw and place lubricant tube into the fill hole.

82

MAINTENANCE
4. Add lubricant until it appears at the vent hole.

ob00598

IMPORTANT: Replace sealing washers if damaged. 5. Stop adding lubricant. Install the vent plug and sealing washer before removing the lubricant tube.

ob00599

6. Remove lubricant tube and reinstall cleaned fill/drain plug and sealing washer.

ob00600

Submerged Outboard
A submerged outboard will require service within a few hours by an authorized dealer once the outboard is recovered from the water. This immediate attention by a servicing dealer is necessary once the engine is exposed to the atmosphere to minimize internal corrosion damage to the engine.

83