Access Control Lists: Overview and Guidelines

Cisco provides basic traffic filtering capabilities with access control lists (also referred to as access lists). Access lists can be configured for all routed network protocols (IP, AppleTalk, and so on) to filter the packets of those protocols as the packets pass through a router. You can configure access lists at your router to control access to a network: access lists can prevent certain traffic from entering or exiting a network.

In This Chapter
This chapter describes access lists as part of a security solution. This chapter includes tips, cautions, considerations, recommendations, and general guidelines for how to use access lists. This chapter has these sections:

About Access Control Lists Overview of Access List Configuration Finding Complete Configuration and Command Information for Access Lists

About Access Control Lists

This section briefly describes what access lists do; why and when you should configure access lists; and basic versus advanced access lists. This section has the following sections:

What Access Lists Do Why You Should Configure Access Lists When to Configure Access Lists Basic Versus Advanced Access Lists

What Access Lists Do

Access lists filter network traffic by controlling whether routed packets are forwarded or blocked at the routers interfaces. Your router examines each packet to determine whether to forward or drop the packet, on the basis of the criteria you specified within the access lists.

Cisco IOS Security Configuration Guide

SC-177

Access Control Lists: Overview and Guidelines About Access Control Lists

Access list criteria could be the source address of the traffic, the destination address of the traffic, the upper-layer protocol, or other information. Note that sophisticated users can sometimes successfully evade or fool basic access lists because no authentication is required.

Why You Should Configure Access Lists

There are many reasons to configure access lists; for example, you can use access lists to restrict contents of routing updates or to provide traffic flow control. One of the most important reasons to configure access lists is to provide security for your network, which is the focus of this chapter. You should use access lists to provide a basic level of security for accessing your network. If you do not configure access lists on your router, all packets passing through the router could be allowed onto all parts of your network. Access lists can allow one host to access a part of your network and prevent another host from accessing the same area. In Figure 14, host A is allowed to access the Human Resources network, and host B is prevented from accessing the Human Resources network.
Figure 14 Using Traffic Filters to Prevent Traffic from Being Routed to a Network

Host A

Host B

Human Resources network

Research & Development network

You can also use access lists to decide which types of traffic are forwarded or blocked at the router interfaces. For example, you can permit e-mail traffic to be routed, but at the same time block all Telnet traffic.

When to Configure Access Lists

Access lists should be used in firewall routers, which are often positioned between your internal network and an external network such as the Internet. You can also use access lists on a router positioned between two parts of your network, to control traffic entering or exiting a specific part of your internal network. To provide the security benefits of access lists, you should at a minimum configure access lists on border routersrouters situated at the edges of your networks. This provides a basic buffer from the outside network, or from a less controlled area of your own network into a more sensitive area of your network.

Cisco IOS Security Configuration Guide

SC-178

S5032

Access Control Lists: Overview and Guidelines Overview of Access List Configuration

On these routers, you should configure access lists for each network protocol configured on the router interfaces. You can configure access lists so that inbound traffic or outbound traffic or both are filtered on an interface. Access lists must be defined on a per-protocol basis. In other words, you should define access lists for every protocol enabled on an interface if you want to control traffic flow for that protocol.

Note

Some protocols refer to access lists as filters.

Basic Versus Advanced Access Lists

This chapter describes how to use standard and static extended access lists, which are the basic types of access lists. Some type of basic access list should be used with each routed protocol that you have configured for router interfaces. Besides the basic types of access lists described in this chapter, there are also more advanced access lists available, which provide additional security features and give you greater control over packet transmission. These advanced access lists and features are described in the other chapters within the part Traffic Filtering and Firewalls.

Overview of Access List Configuration

Each protocol has its own set of specific tasks and rules that are required in order for you to provide traffic filtering. In general, most protocols require at least two basic steps to be accomplished. The first step is to create an access list definition, and the second step is to apply the access list to an interface. The following sections describe these two steps:

Creating Access Lists Applying Access Lists to Interfaces

Note that some protocols refer to access lists as filters and refer to the act of applying the access lists to interfaces as filtering.

Creating Access Lists

Create access lists for each protocol you wish to filter, per router interface. For some protocols, you create one access list to filter inbound traffic, and one access list to filter outbound traffic. To create an access list, you specify the protocol to filter, you assign a unique name or number to the access list, and you define packet filtering criteria. A single access list can have multiple filtering criteria statements. Cisco recommends that you create your access lists on a TFTP server and then download the access lists to your router. This approach can considerably simplify maintenance of your access lists. For details, see the Creating and Editing Access List Statements on a TFTP Server section later in this chapter.

Cisco IOS Security Configuration Guide

SC-179

Access Control Lists: Overview and Guidelines Overview of Access List Configuration

The protocols for which you can configure access lists are identified in Table 16. This section has the following sections:

Assigning a Unique Name or Number to Each Access List Defining Criteria for Forwarding or Blocking Packets Creating and Editing Access List Statements on a TFTP Server

Assigning a Unique Name or Number to Each Access List

When configuring access lists on a router, you must identify each access list uniquely within a protocol by assigning either a name or a number to the protocols access list.

Note

Access lists of some protocols must be identified by a name, and access lists of other protocols must be identified by a number. Some protocols can be identified by either a name or a number. When a number is used to identify an access list, the number must be within the specific range of numbers that is valid for the protocol. You can specify access lists by names for the following protocols:

Apollo Domain IP IPX ISO CLNS NetBIOS IPX Source-route bridging NetBIOS

You can specify access lists by numbers for the protocols listed in Table 16. Table 16 also lists the range of access list numbers that is valid for each protocol.
Table 16 Protocols with Access Lists Specified by Numbers

Protocol IP Extended IP Ethernet type code Ethernet address Transparent bridging (protocol type) Transparent bridging (vendor code) Extended transparent bridging DECnet and extended DECnet XNS Extended XNS AppleTalk Source-route bridging (protocol type) Source-route bridging (vendor code)

Range 199, 13001999 100199, 20002699 200299 700799 200299 700799 11001199 300399 400499 500599 600699 200299 700799

Cisco IOS Security Configuration Guide

SC-180

Access Control Lists: Overview and Guidelines Overview of Access List Configuration

Table 16

Protocols with Access Lists Specified by Numbers (continued)

Protocol IPX Extended IPX IPX SAP Standard VINES Extended VINES Simple VINES

Range 800899 900999 10001099 1100 101200 201300

Defining Criteria for Forwarding or Blocking Packets

When creating an access list, you define criteria that are applied to each packet that is processed by the router; the router decides whether to forward or block each packet on the basis of whether or not the packet matches the criteria. Typical criteria you define in access lists are packet source addresses, packet destination addresses, and upper-layer protocol of the packet. However, each protocol has its own specific set of criteria that can be defined. For a single access list, you can define multiple criteria in multiple, separate access list statements. Each of these statements should reference the same identifying name or number, to tie the statements to the same access list. You can have as many criteria statements as you want, limited only by the available memory. Of course, the more statements you have, the more difficult it will be to comprehend and manage your access lists.

The Implied Deny All Traffic Criteria Statement

At the end of every access list is an implied deny all traffic criteria statement. Therefore, if a packet does not match any of your criteria statements, the packet will be blocked.

Note

For most protocols, if you define an inbound access list for traffic filtering, you should include explicit access list criteria statements to permit routing updates. If you do not, you might effectively lose communication from the interface when routing updates are blocked by the implicit deny all traffic statement at the end of the access list.

The Order in Which You Enter Criteria Statements

Note that each additional criteria statement that you enter is appended to the end of the access list statements. Also note that you cannot delete individual statements after they have been created. You can only delete an entire access list. The order of access list statements is important! When the router is deciding whether to forward or block a packet, the Cisco IOS software tests the packet against each criteria statement in the order in which the statements were created. After a match is found, no more criteria statements are checked. If you create a criteria statement that explicitly permits all traffic, no statements added later will ever be checked. If you need additional statements, you must delete the access list and retype it with the new entries.

Cisco IOS Security Configuration Guide

SC-181

Access Control Lists: Overview and Guidelines Overview of Access List Configuration

Creating and Editing Access List Statements on a TFTP Server

Because the order of access list criteria statements is important, and because you cannot reorder or delete criteria statements on your router, Cisco recommends that you create all access list statements on a TFTP server, and then download the entire access list to your router. To use a TFTP server, create the access list statements using any text editor, and save the access list in ASCII format to a TFTP server that is accessible by your router. Then, from your router, use the copy tftp:file_id system:running-config command to copy the access list to your router. Finally, perform the copy system:running-config nvram:startup-config command to save the access list to your routers NVRAM. Then, if you ever want to make changes to an access list, you can make them to the text file on the TFTP server, and copy the edited file to your router as before.

Note

The first command of an edited access list file should delete the previous access list (for example, type a no access-list command at the beginning of the file). If you do not first delete the previous version of the access list, when you copy the edited file to your router you will merely be appending additional criteria statements to the end of the existing access list.

Applying Access Lists to Interfaces

For some protocols, you can apply up to two access lists to an interface: one inbound access list and one outbound access list. With other protocols, you apply only one access list which checks both inbound and outbound packets. If the access list is inbound, when the router receives a packet, the Cisco IOS software checks the access lists criteria statements for a match. If the packet is permitted, the software continues to process the packet. If the packet is denied, the software discards the packet. If the access list is outbound, after receiving and routing a packet to the outbound interface, the software checks the access lists criteria statements for a match. If the packet is permitted, the software transmits the packet. If the packet is denied, the software discards the packet.

Note

Access lists that are applied to interfaces do not filter traffic that originates from that router.

Cisco IOS Security Configuration Guide

SC-182

Access Control Lists: Overview and Guidelines Finding Complete Configuration and Command Information for Access Lists

Finding Complete Configuration and Command Information for Access Lists

The guidelines discussed in this chapter apply in general to all protocols. The specific instructions for creating access lists and applying them to interfaces vary from protocol to protocol, and this specific information is not included in this chapter. To find complete configuration and command information to configure access lists for a specific protocol, see the corresponding chapters in the Cisco IOS configuration guides and command references. For example, to configure access lists for the IP protocol, refer to the section "Filtering IP Packets Using Access Lists" in the Configuring IP Services" chapter of the Cisco IOS IP Configuration Guide, Release 12.2. For information on dynamic access lists, see the chapter Configuring Lock-and-Key Security (Dynamic Access Lists) later in this book. For information on reflexive access lists, see the chapter Configuring IP Session Filtering (Reflexive Access Lists) later in this book.

Cisco IOS Security Configuration Guide

SC-183

Access Control Lists: Overview and Guidelines Finding Complete Configuration and Command Information for Access Lists

Cisco IOS Security Configuration Guide

SC-184