m5 L5-Population Forecasting

Module 5, Lecture Number-05 M.M.
Ghangrekar, IIT Kharagpur

1

Module 5:
Population Forecasting

Lecture 5:
Population Forecasting

Wastewater Management

5. POPULATION FORECASTING

Design of water supply and sanitation scheme is based on the projected population of a
particular city, estimated for the design period. Any underestimated value will make system
inadequate for the purpose intended; similarly overestimated value will make it costly.
Change in the population of the city over the years occurs, and the system should be designed
taking into account of the population at the end of the design period.

Factors affecting changes in population are:
increase due to births
decrease due to deaths
increase/ decrease due to migration
increase due to annexation.
The present and past population record for the city can be obtained from the census
population records. After collecting these population figures, the population at the end of
design period is predicted using various methods as suitable for that city considering the
growth pattern followed by the city.

5.1 ARITHMETICAL INCREASE METHOD
This method is suitable for large and old city with considerable development. If it is used for
small, average or comparatively new cities, it will give low result than actual value. In this
method the average increase in population per decade is calculated from the past census
reports. This increase is added to the present population to find out the population of the next
decade. Thus, it is assumed that the population is increasing at constant rate.
Hence, dP/dt =C i.e. rate of change of population with respect to time is constant.

Therefore, Population after n
th
decade will be P
n
=P +n.C
Where, P
n
is the population after n decade and P is present population.

Module 5, Lecture Number-05 M.M. Ghangrekar, IIT Kharagpur

3

Example:1

Predict the population for the year 2021, 2031, and 2041 from the following population data.
Year 1961 1971 1981 1991 2001 2011
Population 8,58,545 10,15,672 12,01,553 16,91,538, 20,77,820, 25,85,862

Solution

Year Population Increment
1961 858545 -
1971 1015672 157127
1981 1201553 185881
1991 1691538 489985
2001 2077820 386282
2011 2585862 508042
Average increment =345463

Population in year 2021 is, P
2021
=2585862 +345463 x 1 =2931325
Similarly, P
2031
=2585862 +345463 x 2 =3276788
P
2041
=2585862 +345463 x 3 =3622251

5.2 GEOMETRICAL INCREASE METHOD
(OR GEOMETRICAL PROGRESSION METHOD)

In this method the percentage increase in population from decade to decade is assumed to
remain constant. Geometric mean increase is used to find out the future increment in
population. Since this method gives higher values and hence should be applied for a new
industrial town at the beginning of development for only few decades. The population at the
end of n
th
decade P
n
can be estimated as:
P
n
=P (1+I
G
/100)
n
Where, I
G
=geometric mean (%)
P =Present population
N =no. of decades.


Example : 2

Considering data given in example 1 predict the population for the year 2021, 2031, and 2041
using geometrical progression method.

Solution
Year Population Increment Geometrical increase
Rate of growth
1961 858545 -
1971 1015672 157127 (157127/858545)
=0.18
1981 1201553 185881 (185881/1015672)
=0.18
1991 1691538 489985 (489985/1201553)
=0.40
2001 2077820 386282 (386282/1691538)
=0.23
2011 2585862 508042 (508042/2077820)
=0.24

Geometric mean I
G
=(0.18 x 0.18 x 0.40 x 0.23 x 0.24)
1/4

=0.235 i.e., 23.5%
2021
=2585862 x (1+0.235)
1
=3193540
Similarly for year 2031 and 2041 can be calculated by,
P
2031
=2585862 x (1+0.235)
2
=3944021
P
2041
=2585862 x (1+0.235)
3
=4870866

5.3 INCREMENTAL INCREASE METHOD
This method is modification of arithmetical increase method and it is suitable for an average
size town under normal condition where the growth rate is found to be in increasing order.
While adopting this method the increase in increment is considered for calculating future
population. The incremental increase is determined for each decade from the past population
and the average value is added to the present population along with the average rate of
increase.
Hence, population after n
th
decade is P
n
=P+n.X +{n (n+1)/2}.Y
Where, P
n
=Population after n
th
decade
X =Average increase
Y =Incremental increase

5

Example : 3

Considering data given in example 1 predict the population for the year 2021, 2031, and 2041
using incremental increase method.

Year Population Increase (X) Incremental increase (Y)
1961 858545 - -
1971 1015672 157127 -
1981 1201553 185881 +28754
1991 1691538 489985 +304104
2001 2077820 386282 -103703
2011 2585862 508042 +121760
Total 1727317 350915
Average 345463 87729

2021
=2585862 +(345463 x 1) +{(1 (1+1))/2} x 87729
=3019054
For year 2031 P
2031
=2585862 +(345463 x 2) +{((2 (2+1)/2)}x 87729
=3539975
P
2041
=2585862 +(345463 x 3) +{((3 (3+1)/2)}x 87729
=4148625

5.4 GRAPHICAL METHOD
In this method, the populations of last few decades are correctly plotted to a suitable scale on
graph. The population curve is smoothly extended for getting future population. This
extension should be done carefully and it requires proper experience and judgment. The best
way of applying this method is to extend the curve by comparing with population curve of
some other similar cities having the similar growth condition.


Figure 5.1 Graphical method of population forecasting

5.5 COMPARATIVE GRAPHICAL METHOD
In this method the census populations of cities already developed under similar conditions are
plotted. The curve of past population of the city under consideration is plotted on the same
graph. The curve is extended carefully by comparing with the population curve of some
similar cities having the similar condition of growth. The advantage of this method is that the
future population can be predicted from the present population even in the absent of some of
the past census report. The use of this method is explained by a suitable example given
below.
Example: 4
Let the population of a new city X be given for decades 1970, 1980, 1990 and 2000 were
32,000; 38,000; 43,000 and 50,000, respectively. The cities A, B, C and D were developed in
similar conditions as that of city X. It is required to estimate the population of the city X in
the years 2010 and 2020. The population of cities A, B, C and D of different decades were
given below:
(i) City A was 50,000; 62,000; 72,000 and 87,000 in 1960, 1972, 1980 and 1990,
respectively.
0.00
0.10
0.20
0.30
0.40
0.50
0.60
1941 1951 1961 1971 1981 1991 2001 2011 2021 2031 2041 2051
P
o
p
u
l
a
t
i
o
n
i
n
L
a
k
h
s
Year

7

(ii) City B was 50,000; 58,000; 69,000 and 76,000 in 1962, 1970, 1981 and 1988,
respectively.
(iii) City C was 50,000; 56,500; 64,000 and 70,000 in 1964, 1970, 1980 and 1988,
respectively.
(iv) City D was 50,000; 54,000; 58,000 and 62,000 in 1961, 1973, 1982 and 1989,
respectively.
Population curves for the cities A, B, C, D and X were plotted. Then an average mean curve
is also plotted by dotted line as shown in the figure. The population curve X is extended
beyond 50,000 matching with the dotted mean curve. From the curve the populations
obtained for city X are 58,000 and 68,000 in year 2010 and 2020.

Figure 5.2 Comparative graph method
5.6 MASTER PLAN METHOD
The big and metropolitan cities are generally not developed in haphazard manner, but are
planned and regulated by local bodies according to master plan. The master plan is prepared
for next 25 to 30 years for the city. According to the master plan the city is divided into
various zones such as residence, commerce and industry. The population densities are fixed
for various zones in the master plan. From this population density total water demand and
wastewater generation for that zone can be worked out. So by this method it is very easy to
access precisely the design population.

0
20
40
60
80
100
1960 1970 1980 1990 2000 2010 2020
P
o
p
u
l
a
t
i
o
n

i
n

t
h
o
u
s
a
n
d
Year
Population curve
A
B
C
D
X

5.7 LOGISTIC CURVE METHOD
This method is used when the growth rate of population due to births, deaths and migrations
takes place under normal situation and it is not subjected to any extraordinary changes like
epidemic, war, earth quake or any natural disaster etc. the population follow the growth curve
characteristics of living things within limited space and economic opportunity. If the
population of a city is plotted with respect to time, the curve so obtained under normal
condition is look like S-shaped curve and is known as logistic curve.

Figure 5.3 Logistic curve for population growth

In figure, the curve shows an early growth J K at an increasing rate i.e. geometric growth or
log growth,
dP
dt
P, the transitional middle curve KM follows arithmetic increase i.e.
dP
dt
=
constant and later growth MN the rate of change of population is proportional to difference
between saturation population and existing population, i.e.
dP
dt
(P
s
-P). Verhaulst has put
forward a mathematical solution for this logistic curve J N which can be represented by an
autocatalytic first order equation, given by
log
e
(
Ps-P
P
) - log
e
(
Ps-P0
P0
) =-K.P
s
.t
where, P =Population at any time t from the origin J
J
K
M
N
P
Pointof
inflexion
Curveof
growthrate
L
SaturationPopulation,Ps

9

P
s
=Saturation population
P
0
=Population of the city at the start point J
K =Constant
t =Years
From the above equation we get
log
e

Ps-P
P

P0
Ps-P0
=- K.P
s
.t
After solving we get,
P =
P
s
1+
P
s - P
c
P
c
Iog
c
-1
(-K.P
s
.t)

Substituting
Ps-P0
P0
=m (a constant)
and - K.P
s
=n (another constant)
we get P =
P
s
1+ mIog
e
-1
(n.t)

This is the required equation of the logistic curve, which will be used for predicting
population. McLean further suggested that if only three pairs of characteristic values P
0
, P
1
,
P
2
at times t =t
0
=0, t
1
and t
2
=2t
1
extending over the past record are chosen, the saturation
population P
s
and constant m and n can be estimated by the following equation, as follows:
P
s
=
2P
0
P
1
P
2
-P
1
2
(P
0
+ P
2
)
P
0
P
2
-P
1
2

m =
Ps-P0
P0

n =
2.S
t
1
log
10
P
0
(P
s
-P
1
)
P
1
(P
s
P
0
)

Example: 5
The population of a city in three consecutive years i.e. 1991, 2001 and 2011 is 80,000;
250,000 and 480,000, respectively. Determine (a) The saturation population, (b) The equation
of logistic curve, (c) The expected population in 2021.


Solution
It is given that
P
0
=80,000 t
0
=0
P
1
=250,000 t
1
=10 years
P
2
=480,000 t
2
=20 years
The saturation population can be calculated by using equation
P
s
=
2P
0
P
1
P
2
-P
1
2
(P
0
+ P
2
)
P
0
P
2
-P
1
2

=
2 x 80,000 x 2,50,000 x 4,80,000-2,50,000 x 2,50,000 x (80,000 + 4,80,000)
80,000 x 4,80,000 -2,50,000 x 2,50,000

=655,602
We have m =
Ps-P0
P0
=
655,602-80,000
80,000
=7.195
n =
2.S
t
1
log
10
P
0
(P
s
-P
1
)
P
1
(P
s
P
0
)

=
2.S
1u
log10
80,000(655,602-2,50,000)
250,000(655,602 80,000)

=-0.1488
Population in 2021
P =
P
s
1+ mIog
e
-1
(n.t)

=
6,SS,6u2
1+ 7.19S x log
e
-1
(-u.1488 x Su)

=
6,SS,6u2
1+ 7.19S x 0.0117
=605,436


11

Questions
1. Explain different methods of population forecasting.
2. The population data for a town is given below. Find out the population in the year
2021, 2031 and 2041 by (a) arithmetical (b) geometric (c) incremental increase
methods.
Year 1971 1981 1991 2001 2011
Population 84,000 1, 15,000 1, 60,000 2, 05,000 2, 50,000
3. In three consecutive decades the population of a town is 40,000; 100,000 and
130,000. Determine: (a) Saturation population; (b) Equation for logistic curve; (c)
Expected population in next decade.

m5 L5-Population Forecasting

Uploaded by

Copyright:

Available Formats

m5 L5-Population Forecasting

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

m5 L5-Population Forecasting

Uploaded by

Copyright:

Available Formats

Module 5, Lecture Number-05 M.M.

Ghangrekar, IIT Kharagpur

You might also like