Navedtra 14256 PDF

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.
NONRESIDENT TRAINING COURSE

June 1992
Tools and Their Uses

NAVEDTRA 14256
DISTRIBUTION STATEMENT A : Approved for public release; distribution is unlimited.
Although the words he, him, and his are used sparingly in this course to enhance communication, they are not intended to be gender driven or to affront or discriminate against anyone.
DISTRIBUTION STATEMENT A : Approved for public release; distribution is unlimited.
NAVAL EDUCATION AND TRAINING PROGRAM MANAGEMENT SUPPORT ACTIVITY PENSACOLA, FLORIDA 32559-5000 ERRATA NO. 1 May 1993
Specific Instructions and Errata for Nonresident Training Course TOOLS AND THEIR USES TO OBTAIN CREDIT FOR DELETED QUESTIONS, SHOW THIS ERRATA TO 1. THE LOCAL COURSE YOUR LOCAL-COURSE ADMINISTRATOR (ESO/SCORER). ADMINISTRATOR (ESO/SCORER) IS DIRECTED TO CORRECT THE ANSWER KEY FOR THIS COURSE BY INDICATING THE QUESTIONS DELETED. No attempt has been made to issue corrections for errors in 2. typing, punctuation, etc., which will not affect your ability to answer the question. 3. Assignment Booklet
Delete the following questions and write "Deleted" across all four of the boxes for that question: Question 2-7 2-54 Question 5-43 5-46
PREFACE
By enrolling in this self-study course, you have demonstrated a desire to improve yourself and the Navy. Remember, however, this self-study course is only one part of the total Navy training program. Practical experience, schools, selected reading, and your desire to succeed are also necessary to successfully round out a fully meaningful training program. THE COURSE: This self-study course is organized into subject matter areas, each containing learning objectives to help you determine what you should learn along with text and illustrations to help you understand the information. The subject matter reflects day-to-day requirements and experiences of personnel in the rating or skill area. It also reflects guidance provided by Enlisted Community Managers (ECMs) and other senior personnel, technical references, instructions, etc., and either the occupational or naval standards, which are listed in the Manual of Navy Enlisted Manpower Personnel Classifications and Occupational Standards, NAVPERS 18068. THE QUESTIONS: The questions that appear in this course are designed to help you understand the material in the text. VALUE: In completing this course, you will improve your military and professional knowledge. Importantly, it can also help you study for the Navy-wide advancement in rate examination. If you are studying and discover a reference in the text to another publication for further information, look it up.
Published by NAVAL EDUCATION AND TRAINING PROFESSIONAL DEVELOPMENT AND TECHNOLOGY CENTER
NAVSUP Logistics Tracking Number 0504-LP-026-8900
Sailors Creed
I am a United States Sailor. I will support and defend the Constitution of the United States of America and I will obey the orders of those appointed over me. I represent the fighting spirit of the Navy and those who have gone before me to defend freedom and democracy around the world. I proudly serve my countrys Navy combat team with honor, courage and commitment. I am committed to excellence and the fair treatment of all.
INSTRUCTIONS FOR TAKING THE COURSE

ASSIGNMENTS The text pages that you are to study are listed at the beginning of each assignment. Study these pages carefully before attempting to answer the questions. Pay close attention to tables and illustrations and read the learning objectives. The learning objectives state what you should be able to do after studying the material. Answering the questions correctly helps you accomplish the objectives. SELECTING YOUR ANSWERS Read each question carefully, then select the BEST answer. You may refer freely to the text. The answers must be the result of your own work and decisions. You are prohibited from referring to or copying the answers of others and from giving answers to anyone else taking the course. SUBMITTING YOUR ASSIGNMENTS To have your assignments graded, you must be enrolled in the course with the Nonresident Training Course Administration Branch at the Naval Education and Training Professional and Technology Development Center (NETPDTC). Following enrollment, there are two ways of having your assignments graded: (1) use the Internet to submit your assignments as you complete them, or (2) send all the assignments at one time by mail to NETPDTC. Grading on the Internet: Internet grading are: Advantages to assignments. To submit your assignment answers via the Internet, go to: http://courses.cnet.navy.mil Grading by Mail: When you submit answer sheets by mail, send all of your assignments at one time. Do NOT submit individual answer sheets for grading. Mail all of your assignments in an envelope, which you either provide yourself or obtain from your nearest Educational Services Officer (ESO). Submit answer sheets to: COMMANDING OFFICER NETPDTC N331 6490 SAUFLEY FIELD ROAD PENSACOLA FL 32559-5000 Answer Sheets: All courses include one scannable answer sheet for each assignment. These answer sheets are preprinted with your SSN, name, assignment number, and course number. Explanations for completing the answer sheets are on the answer sheet. Do not use answer sheet reproductions: Use only the original answer sheets that we providereproductions will not work with our scanning equipment and cannot be processed. Follow the instructions for marking your answers on the answer sheet. Be sure that blocks 1, 2, and 3 are filled in correctly. This information is necessary for your course to be properly processed and for you to receive credit for your work. COMPLETION TIME Courses must be completed within 12 months from the date of enrollment. This includes time required to resubmit failed assignments.
you may submit your answers as soon as you complete an assignment, and you get your results faster; usually by the next working day (approximately 24 hours). In addition to receiving grade results for each assignment, you will receive course completion confirmation once you have completed all the
iii
PASS/FAIL ASSIGNMENT PROCEDURES If your overall course score is 3.2 or higher, you will pass the course and will not be required to resubmit assignments. Once your assignments have been graded you will receive course completion confirmation. If you receive less than a 3.2 on any assignment and your overall course score is below 3.2, you will be given the opportunity to resubmit failed assignments. Y o u m a y resubmit failed assignments only once. Internet students will receive notification when they have failed an assignment--they may then resubmit failed assignments on the web site. Internet students may view and print results for failed assignments from the web site. Students who submit by mail will receive a failing result letter and a new answer sheet for resubmission of each failed assignment. COMPLETION CONFIRMATION After successfully completing this course, you will receive a letter of completion. ERRATA Errata are used to correct minor errors or delete obsolete information in a course. Errata may also be used to provide instructions to the student. If a course has an errata, it will be included as the first page(s) after the front cover. Errata for all courses can be accessed and viewed/downloaded at:
http://www.advancement.cnet.navy.mil
For subject matter questions: E-mail: Phone: [email protected] Comm: (850) 452-1001, Ext. 1826 DSN: 922-1001, Ext. 1826 FAX: (850) 452-1370 (Do not fax answer sheets.) Address: COMMANDING OFFICER NETPDTC (CODE N314) 6490 SAUFLEY FIELD ROAD PENSACOLA FL 32509-5237 For enrollment, shipping, grading, or completion letter questions E-mail: Phone: [email protected] Toll Free: 877-264-8583 Comm: (850) 452-1511/1181/1859 DSN: 922-1511/1181/1859 FAX: (850) 452-1370 (Do not fax answer sheets.) Address: COMMANDING OFFICER NETPDTC (CODE N331) 6490 SAUFLEY FIELD ROAD PENSACOLA FL 32559-5000 NAVAL RESERVE RETIREMENT CREDIT If you are a member of the Naval Reserve, you will receive retirement points if you are authorized to receive them under current directives governing retirement of Naval Reserve personnel. For Naval Reserve retirement, this course is evaluated at 8 points. (Refer to Administrative Procedures for Naval Reservists on Inactive Duty, BUPERSINST 1001.39, for more information about retirement points.) COURSE OBJECTIVES In completing this nonresident training course, the student will demonstrate a knowledge of the use and care of various hand tools and measuring tools by correctly answering questions on the following: the types and uses of a large number of hand tools, safety precautions that must be followed when using hand tools, general care of hand tools, and repair procedures for some of the hand tools.
STUDENT FEEDBACK QUESTIONS We value your suggestions, questions, and criticisms on our courses. If you would like to communicate with us regarding this course, we encourage you, if possible, to use e-mail. If you write or fax, please use a copy of the Student Comment form that follows this page.
iv
Student Comments
Course Title: NAVEDTRA: Tools and Their Uses 14256 Date:
We need some information about you: Rate/Rank and Name: Street Address: Your comments, suggestions, etc.: SSN: City: Command/Unit State/FPO: Zip
Privacy Act Statement: Under authority of Title 5, USC 301, information regarding your military status is requested in processing your comments and in preparing a reply. This information will not be divulged without written authorization to anyone other than those within DOD for official use in determining performance.
NETPDTC 1550/41 (Rev 4-00)
*TM 9-243 M6290-AJ-MAN-010 TO 32-1-101 TM 10209-10/1

TECHNICAL MANUAL NO. 9-243 NAVY M6290-A-J-MAN-010 TECHNICAL ORDER NO. 32-1-101 TECHNICAL MANUAL NO. 10209-1011 DEPARTMENTS OF THE ARMY, NAVY, AIR FORCE AND MARINE CORPS
WASHINGTON, DC, 12 December 1983
USE AND CARE OF HAND TOOLS AND MEASURING TOOLS

REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS You can help improve this manual. If you find any mistakes or if you know of a way to improve the procedures, please let us know. Mail your letter, DA Form 2028 (Recommended Changes to Publications and Blank Forms), or DA Form 2028-2, located in the back of this manual direct to: Commander, US Army Armament, Munitions and Chemical Command, ATTN: AMSMC-MAS, Rock Island, IL 612996000. A reply will be furnished directly to you. Page 1-1 2-1 3-1 4-1 5-1 6-1 7-1 8-1 9-1 10-1 11-1 12-1 13-1 14-1 15-1 16-1 17-1 18-1 19-1 20-1 21-1 22-1 23-1 24-1 25-1 26-1 27-1 28-1 29-1 30-1 31-1 32-1 33-1 34-1 35-1 36-1
CHAPTER
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety and safety equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reading measuring scales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Toolboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dividers.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Calipers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Micrometers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rules and steel tapes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Miscellaneous measuring tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Plumb bobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scribers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Squares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Surface, depth, and height gages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ring and snap gages and gage blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Miscellaneous measuring gages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pliers and tongs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vises. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clamps.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hammers, mallets, and mauls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Screwdrivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual drills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Screw and tap extractors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wrenches.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chisels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Punches.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grinders and sharpening stones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scrapers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Awls.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bolt and cable cutters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glasscutters.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Knives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pipe cutting and threading tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tube cutting and flaring tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
*This manual supersedes TM 9-243.14 September 1960, and TO 32-l-101.19 April 1945.
Change 1
TM 9-243
Page 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. A 37-1 Shears and nippers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-1 Taps and dies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39-1 Reamers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-1 Benders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-1 Pullers.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-1 Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-1 Mattocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-1 Gasket cutters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-1 Chopping tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-1 Saws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47-1 Brushcutting tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-1 Timber handling tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-1 Climbing tools.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-1 Planes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-1 Digging tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-1 Electrical power tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53-1 Miscellaneous tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 References.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index 1
A PPENDIX ALPHABETICAL
ii
Change 1
TM 9-243
Chapter 1 INTRODUCTION
PURPOSE
This manual provides information on the use and care of selected hand tools and measuring tools. It will explain the types and uses of a large number of tools, a practical application of a selected group of tools, safety requirements, general care, and limited repair. A user must have, choose, and use the correct tools in order to do the work quickly, accurately, and safely. Without the proper tools and knowledge of how to use them, the user wastes time, reduces efficiency, and may face injury.
HOW TO USE THIS MANUAL

When you need information about a specific tool or operation, simply refer to the alphabetical index at the end of the manual and turn to the pages that apply. The introduction to each tool chapter will furnish information on: How to choose and use the tools covered, the various types of tools available, and an example of their use. Instructions on the care of tools and safety precautions follow.
1-1/(1-2 blank)
TM 9-243
Chapter 2 SAFETY
SAFETY AND SAFETY EQUIPMENT
No matter how small the job, safety must be practiced at all times. A tool may be efficient, essential, time-saving or even convenient; but it is also dangerous. When using any hand tool you must use it correctly, following the methods prescribed in this manual. You must also be alert for any conditions that might endanger yourself or fellow workers. Take the time necessary to acquaint yourself with the safety guidelines in this chapter. Remember, you are the most important part of safety procedures. INDEX
Item Page
SAFETY RULES (GENERAL) . . . . . . . . . . 2-1 Tool habits . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 SAFETY RULES (POWER TOOLS) . . . . 2-3 SAFETY EQUIPMENT . . . . . . . . . . . . . . . . 2-3 Safety shoes . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Eye protection . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Helmets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Gloves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Safety belts and safety straps. . . . . . . . . . . . 2-4 Ear protection . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Section I. SAFETY RULES (GENERAL)

There will undoubtedly be a safety program to follow for the shop or area in which you will be working. The following general safety rules are furnished as a guide. 1. SUPPORT your local safety program and take an active part in safety meetings. 2. INSPECT tools and equipment for safe conditions before starting work. 3. ADVISE your supervisor promptly of any unsafe conditions or practices. 4. LEARN the safe way to do your job before you start. 5. THINK safety, and ACT safety at all times. 6. OBEY safety rules and regulations-they are for your protection. 7. WEAR proper clothing and protective equipment. 8. CONDUCT yourself properly at all times-horseplay is prohibited. 9. OPERATE only the equipment you are authorized to use. 10. REPORT any injury immediately to your supervisor. In addition to the above, there are other good tool habits which will help you perform your work more efficiently as well as safely.
TOOL HABITS
A place for everything and everything in its place is just common sense. You cannot do an efficient, fast repair job if you have to stop and look around for each tool that you need. The following rules, if applied, will make your job easier.
2-1
TM 9-243
TOOL HABITS - Continued
KEEP EACH TOOL IN ITS PROPER STORAGE PLACE. A tool is useless if you cannot find it. If you return each tool to its proper place, you will know where it is when you need it.
KEEP YOUR TOOLS WITHIN EASY REACH AND WHERE THEY CANNOT FALL ON THE FLOOR OR ON MACHINERY. Avoid placing tools anywhere above machinery or electrical apparatus. Serious damage will result if the tool falls into the machinery after the equipment is turned on or running. NOTE Return broken tools to section chief.
KEEP YOUR TOOLS IN GOOD CONDITION. Keep them free of rust, nicks, burrs, and breaks. KEEP YOUR TOOL SETCOMPLETE. If you are issued a tool box, each tool should be placed in it when not in use. If possible, the box should be locked and stored in a designated area. Keep an inventory list in the box and check it after each job. This will help you to keep track of your tools.
NEVER USE DAMAGED TOOLS. Notify your supervisor of broken or damaged tools. A battered screwdriver may slip and spoil the the screw slot or cause painful injury to the user. A gage strained out of shape wil result in inaccurate measurements. Remember, a workers efficiency is often a direct result of the condition of the tools being used. Workers are often judged by the manner in which they handle and care for their tools. You should care for hand tools the same way you care for personal property. Always keep hand tools clean and free from dirt, grease, and foreign matter. After use, return tools promptly to their proper places in the tool box. Improve your own efficiency by organizing your tools so that those used most frequently can be reached easily without sorting through the entire contents of the box. Avoid accumulating unnecessary items.
USE EACH TOOL ONLY ON THE JOB FOR WHICH IT WAS DESIGNED. If you use the wrong tool to make an adjustment, the result will probably be unsatisfactory. For example, if you use a socket wrench that is too big, you will round off the corners of the wrench or nut. If this rounded wrench or nut is not replaced immediately, the safety of your equipment may be endangered in an emergency.
2-2
Change 1
TM 9-243
Section II.
SAFETY RULES (POWER TOOLS)

the tool to stop, and then remove all waste and scraps from the work area. Store the tool in its proper place. 9. Never plug the power cord of a portable electric tool into a power source before making sure that the source has the correct voltage and type of current called for on the nameplate of the tool. 10. Do not allow power cords to come in contact with sharp objects, nor should they kink or come in contact with oil, grease, hot surfaces, or chemicals. Never use a damaged cord. Replace it immediately. Check electrical cables and cords frequently for overheating. Use only approved extension cords, if needed. See that all cables and cords are positioned carefully so they do not become tripping hazards. Treat electricity with respect. If water is present in the area of electrical tool operation, be extremely cautious and if necessary, disconnect the power tool.
Safety is a very important factor in the use of power tools and cannot be overemphasized. By observing the following safety guidelines, you can ensure maximum benefits from the tools you use and reduce to a minimum the chances of serious injury. 1. Never operate any power equipment unless you are completely familiar with its controls and features. 2. Inspect all portable power tools before using them. See that they are clean and in good condition. 3. Make sure there is plenty of light in the work area. Never work with power tools in dark areas where you cannot see clearly. 4. Before connecting a power tool to a power source, be sure the tool switch is in the OFF position. 5. When operating a power tool, give it your FULL and UNDIVIDED ATTENTION. 6. DO NOT DISTRACT OR IN ANY WAY DISTURB another person while they are operating a power tool. 7. Never try to clear a jammed power tool until it is disconnected from the power source. 8. After using a power tool, turn off the power, disconnect the power source, wait for all movement of
11. 12.
13. 14.
Section Ill. SAFETY EQUIPMENT

Safety equipment is for you. It will protect you from injury and may possibly save your life. Some of the more common types of safety equipment for your personal protection follow. Safety shoes protect and prevent injury or loss of toes. Some safety shoes are designed to limit damage to your toes from falling objects. A steel plate is placed in the toe area of such shoes so that your toes are not crushed if an object falls on them. Other safety shoes are designed for use where danger from sparking could cause an explosion. Such danger is minimized by elimination of all metallic nails and eyelets and the use of soles which
do not cause static electricity.
SAFETY SHOES
2-3
TM 9-243
SAFETY EQUIPMENT - Continued

EYE PROTECTION GLOVES
Proper eye protection is of the highest importance for all personnel. Eye protection is necessary because of hazards caused by infrared and ultraviolet radiation, or by flying objects such as sparks, globules of molten metal, or chipped concrete and wood, etc. These hazards are always present during welding, cutting, soldering, chipping, grinding, and a variety of other operations. It is absolutely necessary for you to use eye protection devices such as helmets, handshields, and goggles during eye-hazard operations. Appropriate use of goggles will limit eye hazards. Some goggles have plastic windows which resist shattering upon impact. Others are designed to limit harmful infrared and ultraviolet radiation from arcs or flames by the use of appropriate filter lenses. Remember, eye damage can be extremely painful. Protect your eyes.
Use gloves whenever you are required to handle rough, scaly, or splintery objects. Two types are shown above. Special flameproof gloves are designed for gas and electric welding in order to limit danger and damage from sparks and other hot, flying objects. Personnel working with electricity are usually required to wear insulating rubber gloves. Be sure to follow all regulations prescribed for the use of gloves. Gloves must not be worn around rotating machinery unless sharp or rough material is being handled. If such is the case, extreme care should be used to prevent the gloves from being caught in the machinery.
SAFETY BELTS AND SAFETY STRAPS
HELMETS
The safety belt and safety strap are a must when working in high places. The safety belt, strapped around the waist, contains pockets for small tools. It also has two D-rings used to attach the safety strap. The safety strap is a nylon-reinforced leather belt that is placed around the item to be climbed. It is then attached to the two D-rings on the safety belt. Detailed use of the safety belt and safety strap is described in chapter 49 of this manual.
Protective helmets (hard hats) come in a variety of shapes. They may be made of tough polyethylene or polycarbonate, one of the toughest hat materials yet developed. When falling objects strike the hats, the shock-absorbing suspension capabilities minimize injuries. Regular hard hats must be insulated so that personnel may be protected from accidental head contacts with electrical circuits and equipment at comparatively low voltages (less than 2200 volts). Electrical workers requiring head protection necessary to their duties or to the working environment, must wear insulating safety helmets or all-purpose protective helmets which must be capable of withstanding 20,000 volt minimum proof-tests.
EAR PROTECTION
Proper hearing protection is a must when working with or around certain types of power tools. Some tools are capable of producing dangerously high noise levels which, if ignored, can result in serious hearing loss or injury. Use the hearing protection regularly.
2-4
TM 9-243
Chapter 3 READING MEASURING SCALES

The following chapter is designed to provide a basic understanding of how to read scales, dials, and gages. It will not provide any information on the actual use of the tools. Reference to this chapter will be made throughout the remainder of the manual. INDEX
Item Page
Reading the scale of a rule or tape . . . . 3-1 Reading a metric rule . . . . . . . . . . . . . . . . 3-3
READING THE SCALE OF A RULE OR TAPE
The more common type rules and tapes are divided into fractions, inches, and feet. Explained here are the scales on a 12-inch steel machinists rule. The rule is divided into twelve inches. The inches are further divided into eighths, sixteenths, thirty-seconds, and sixty-fourths.
Look at the section between the 2 and the 3 on the edge marked with an 8 for eighths. There are eight equally spaced lines. The lengths of these lines differ and indicate different fractions or parts of an inch. The longest line is in the center and is equal to 4/8 or 1/2 inch.
Look at the rule. There is a small numeral marked on the end of the rule nearest the l-inch mark. This numeral indicates the number of divisions per inch. When referring to fractions, always use the reduced name. This is the smallest numerator (top number) and denominator (bottom number). For example, 3/6 can be reduced to 1/2 by dividing both the top and bottom by 3. Generally, fractions may be reduced to their lowest forms by repeated division by 2 or 3.
Each half-inch is divided in half by a slightly shorter line indicating 2/8 or 1/4 on the left and 6/8 or 3/4 on the right.
Each 1/4 inch is divided in half by the shortest line which indicates 1/8 inch, and will indicate 1/8, 3/8, 5/8 and 7/8.
3-1
TM 9-243
READING THE SCALE OF A RULE OR TAPE - Continued

Now turn the rule and look at the edge with a 16 marked on it. To determine the number of 32nds in 5/8, remember four divisions or 4/32 are equal to 1/8 inch. If 1/8 is equal to 4/32, then 5/8 is equal to 20/32 as shown: If 1/8 = 4/32, then 5/8 = 20/32 (4 x 5 = 20)
There are now 16 equal divisions between each inch. Since 2/16 reduces to 1/8, divide each 1/8 into two equal parts producing 1/16, 3/16, 5/16, 7/16, 9/16, 11/16, 13/16, and 15/16. Common tapes and rules usually are not graduated smaller than sixteenths. However, precision measurements require smaller graduations.
Find the 20/32 reading on the scale as shown above. 2. Write the new fraction 2-20/32 inches. Finally, look at the edge marked 64. Each inch is now divided into 64 equal parts.
1.
Look at the back of the machinists rule. Find the edge marked 32 and once again look between the numbers 2 and 3. To read this rule, remember: 1. Thirty-two divisions (32/64) are equal to 1/2 inch. 2. Sixteen divisions (16/64) are equal to 1/4 inch. 3. Eight divisions (8/64) are equal to 1/8 inch. 4. Four divisions (4/64) are equal to 1/16 inch. 5. Two divisions (2/64) are equal to 1/32 inch. To read 2-3/4 inches on this scale, first find the two inch mark. Next, determine the number of 64ths in 3/4.
To read this rule, remember: 1. Sixteen divisions (16/32) are equal to 1/2 inch. 2. Eight divisions (8/32) are equal to 1/4 inch. 3. Four divisions (4/32) are equal to 1/8 inch. 4. Two divisions (2/32) are equal to 1/16 inch. To read 2-5/8 inches on the scale, first find the two inch mark, then determine the number of 32nds in 5/8.
3-2
TM 9-243
READING THE SCALE OF A RULE OR TAPE - Continued

To determine the number of 64ths in 3/4, remember every sixteen divisions or 16/64 are equal to 1/4 inch. If 1/4 is equal to 16/64, then 3/4 is equal to 48/64 as shown: If 1/4 = 16/64, then 3/4 = 48/64 (16x3=48) 1 Locate the number 48 between the 2 and 3 inch marks on the scale. 2. Write the new fraction 2-48/64.
READING A METRIC RULE

The metric system is based upon multiples of ten. For example, there are 10 millimeters in a centimeter and 100 centimeters in a meter. The example provided will deal only with millimeters (mm).
The meter will become the starting point and from-this, two additional scales can be developed for measuring. A meter divided by 100 equals a centimeter (cm), 1/100 or 0.01 meter. Next divide a centimeter (cm) by 10. This will equal a millimeter (mm), 1/1000 or 0.001 meter.
Now lets look at a section of the rule between 2 cm and 3 cm. There are 10 equal divisions which are equal to 1/10 cm or 1 mm. To measure 26 mm, first locate the longest line designated 2 cm or 20 mm. Next count 6 additional lines to find 26 mm. A table for converting from US Common to metric or from metric to US Common may be found inside the back cover of this manual.
3-3/(3-4 blank)
TM 9-243
Chapter 4 TOOL BOXES

HOW TO CHOOSE AND USE THEM
The Types and Uses section provides you with a list of some of the types of tool boxes. These pages should help you select the right tool box to do the job. INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . . Mechanics tool box . . . . . . . . . . . . . . . . . . . Hardwood machinists tool box . . . . . . . . . Portable carpenters tool box . . . . . . . . . . . Cantilevered tray tool box . . . . . . . . . . . . . Removable tray tool box . . . . . . . . . . . . . . . Five-drawer tool box . . . . . . . . . . . . . . . . .
4-2 4-2 4-2 4-2 4-2 4-2 4-2
4-1
TM 9-243
TYPES AND USES

Tool boxes are used for storing tools. They are usually made of steel, but wood and plastics are also used. Portable tool boxes are used for carrying and storing a variety of hand tools. Both special and common tools, such as mechanics, electrician, and carpentry tools can be found in tool boxes. Chest-type tool boxes generally contain larger tools, such as specialized automotive tools or machinists tools, requiring a more permanent location. Some larger tool boxes are mounted on wheels so they can be moved easily from place to place. Tool bags are usually made of canvas. Like the boxes, they are available in a variety of sizes and serve similar functions. Examples of tool boxes are illustrated below.
PORTABLE CARPENTERS TOOL BOX
CANTILEVERED TRAY TOOL BOX
MECHANICS TOOL BOX (Chest Type)
REMOVABLE TRAY TOOL BOX
FIVE-DRAWER PORTABLE TOOL BOX
HARDWOOD MACHINISTS TOOL BOX (Chest Type)
CANVAS TOOL BAG
4-2
TM 9-243
Chapter 5 DIVIDERS
The Types and Uses section provides you with a list of the types of dividers. These pages should help you select the right dividers for the job. The Using Dividers section tells you how to use the dividers to scribe a circle of a desired radius. The Care procedures tell you how to care for the dividers.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . . Spring dividers . . . . . . . . . . . . . . . . . . . . . . . Wing dividers . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2 5-2 5-2 5-3 5-3
5-1
TM 9-243
TYPES AND USES

Dividers are instruments used for measuring distances between two points, transferring or comparing measurements directly from a rule, or for scribing an arc, radius, or circle.
WING DIVIDER
SPRING DIVIDER
A wing-type divider has a steel bar that separates the legs, a lock nut for setting a rough measurement, and an adjustment screw for fine adjustments. The wing-type divider is available in 6, 8, and 12 inch lengths. Also available is a divider with one removable leg, so that a pencil may be inserted.
A spring divider consists of two sharp points at the end of straight legs, held apart by a spring and adjusted by means of a screw and nut. The spring divider is available in sizes from 3 to 10 inches in length.
5-2
TM 9-243
USING A DIVIDER TO SCRIBE A CIRCLE
1 2
Set the desired radius on the dividers using the appropriate graduations on a rule. Place the point of one of the divider legs on the point to be used as the center. 3 Lean the dividers in the direction of movement and scribe the circle by revolving the dividers.
CARE OF DIVIDERS
Keep dividers clean and dry. Protect the points against damage. Store dividers where they will not become bent or broken.
5-3/(5-4 blank)
TM 9-243
Chapter 6 CALIPERS
The Types and Uses section provides you with a list of types of calipers. These pages should help you select the right calipers for the job. The Reading Calipers section tells you how to read special calipers for accurate measurements. By becoming familiar with this procedure, you will learn to make accurate measurements. The Care pages tell you how to keep your calipers in good condition. INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . 6-2 Simple calipers . . . . . . . . . . . . . . . . . . . . . 6-2 Spring-joint calipers . . . . . . . . . . . . . . . . . 6-2 Transfer calipers . . . . . . . . . . . . . . . . . . 6-2 Hermaphrodite calipers . . . . . . . . . . . . . 6-2 Slide calipers . . . . . . . . . . . . . . . . . . . . . . 6-3 Vernier calipers . . . . . . . . . . . . . . . . . . . . 6-3 Trammels . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 READING . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Vernier calipers . . . . . . . . . . . . . . . . . . . . 6-4 Metric calipers . . . . . . . . . . . . . . . . . . . . . 6-5 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
6-1
TM 9-243
TYPES AND USES

Calipers are used to measure diameters. Outside calipers measure outside diameters. Inside calipers measure inside diameters. Simple calipers are used along with a scale to find the measurement. Slide calipers and vernier calipers have their own scales.
TRANSFER CALIPERS
SIMPLE CALIPERS
Transfer calipers are used for measuring chamfered grooves or flanges. A screw attaches a small auxiliary leaf to one of the legs. The measurement is made as with ordinary calipers. The leaf is locked to the leg. The legs may be opened or closed as needed to clear the obstruction. The legs are then brought back and locked to the leaf, restoring them to the original setting.
OUTSIDE CALIPERS
INSIDE CALIPERS
The simple outside calipers are bowlegged. Those used for inside diameters have straight legs with feet turned outward. Calipers are adjusted by pulling or pushing the legs to open or close them.
HERMAPHRODITE CALIPERS
SPRING-JOINT CALIPERS
The hermaphrodite calipers have one straight leg ending in a sharp point. On some models this point is removable. This leg is usually bowlegged. This caliper is used for finding shaft centers or locating shoulders. The spring-joint calipers have the same type of legs, but are joined by a strong spring hinge, screw, and adjustment nut.
6-2
TM 9-243
TYPES AND USES - Continued

SLIDE CALIPERS VERNIER CALIPERS
OUTSIDE
INSIDE
Slide calipers can be used for measuring outside and inside dimensions. Graduations are in inches, fractions, or millimeters. As shown above, one side of the caliper is used to measure outside (1) and the other side is used to measure inside (2) dimensions. Stamped on the frame (3) are the words IN: and OUT (4). You use them when taking inside and outside measurements. The other side of the caliper is used as a straight measuring rule. If necessary, see chapter 3 of this manual for reading scales and rules.
Vernier calipers work like slide calipers. As shown above, vernier calipers can make very accurate outside or inside measurements. A vernier caliper is used by loosening the two locking screws (1) and (2). This allows the movable jaw (3) to move along the rule until desired position is obtained. The locking screw (1) is then retightened securing the movable jaw (3). Any fine adjustments to the vernier scale (4) are then made using adjustment control (5). Locking screw (2) is then secured and vernier caliper is ready to read.
6-3
TM 9-243

TRAMMELS
The trammel measures distances beyond the range of calipers. The instrument consists of a rod or beam (1) to which trams (2) are clamped. The trams (2) carry chucks (3). The trammel can also be used as a divider by changing the points.
READING A VERNIER CALIPER
To read a vernier caliper, you must be able to understand both the steel rule and vernier scales. The steel rule (1) is graduated in 0.025 of an inch. Every fourth division (2) (representing a tenth of an inch) is numbered. The vernier scale (3) is divided into 25 parts and numbered 0, 5, 10, 15, 20, and 25. These 25 parts are equal to 24 parts on the steel rule (1). The difference between the width of one of the 25 spaces on the vernier scale (3) and one of the 24 spaces on the steel rule (1) is 1/1000 of an inch. Read the measurement as shown above. Read the number of whole inches on the top scale (1) to the left of the vernier zero index (4) and record . . . . . . . . . . . . . . . . . 1.000 inch
Read the number of tenths (5) to the left of the vernier zero index (4) and record . . . . . . . . . . . .0.400 inch Read the number of twenty-fifths (6) between the tenths mark(5) and the zero index (4) and record . . . . . . . . . . . . . . . . .3 x .025 = .075 inch Read the highest line on the vernier scale (3) which lines up with the lines on the top scale (7) and record. (Remember 1/25 = .001 inch) . . . . . . . . . . 11/25 or 0.011 inch 1.486 inches TOTAL
6-4
TM 9-243
READING A VERNIER CALIPER - Continued

Most vernier calipers read OUTSIDE on one side and INSIDE on the other side. If a scale isnt marked, and you want to take an inside measurement, read the scale as you would for an outside diameter. Then add the measuring point allowance by referring to manufacturers instructions or the following table.
Size of Caliper English Measure Metric Measure
The vernier scale (3) is divided into 25 parts and is numbered 0, 5, 10, 15, 20 and 25. Read the total number of millimeters (4) to the left of the vernier zero index (5) and record
. . . . . . . . . . . . .32.00 mm
6 inch or 150 mm 12 inch or 300 mm 24 inch or 600 mm 36 inch or 600 mm
Add 0.250 inch .300 inch .300 inch .500 inch
Add 6.35 mm 7.62 mm 7.62 mm 12.70 mm
Read the number of quarters (6) between the millimeter mark and the zero index and record . . . . . . . . .25 mm = (1 quarter) Read the highest line on the vernier scale (3) which lines up with the line on the scale (7) and record . . . . . . . . . . . . . . .18 mm TOTAL 32.43 mm
READING A METRIC CALIPER
CARE OF CALIPERS
1. 2. 3. 4. Store calipers in separate containers provided. Keep graduations and markings on all calipers clean and legible. Do not drop any caliper. Small nicks or scratches can cause inaccurate measurements. Protect caliper points from damage.
The steel rule (1) is divided into centimeters (cm) (2) and the longest lines represent 10 millimeters each. Each millimeter is divided into quarters.
Change 1
6-5/(6-6 blank)
TM 9-243
Chapter 7 MICROMETERS
The Types and Uses section provides you with a list of the types of micrometers. These pages should help you select the right micrometer for the job.
The Reading Micrometers section tells you how to read the different varieties of micrometers. By becoming familiar with the procedures you will learn to make accurate measurements.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . 7-2 Outside micrometers . . . . . . . . . . . . . . . . . . 7-2 Inside micrometers . . . . . . . . . . . . . . . . . . . 7-2 Depth micrometers. . . . . . . . . . . . . . . . . . . . 7-2 SELECTING PROPER MICROMETER . . 7-2 READING STANDARD MICROMETER . 7-4 Standard micrometers . . . . . . . . . . . . . . . . 7-4 Vernier micrometers . . . . . . . . . . . . . . . . . 7-5 Metric micrometers . . . . . . . . . . . . . . . . . . . . 7-6 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
7-1
TM 9-243
TYPES AND USES

Micrometers are instruments used to measure distances to the nearest one-thousandth of an inch. The measurement is usually expressed or written as a decimal. There are three types of micrometers which are commonly used: the outside micrometer, the inside micrometer, and the depth micrometer.
INSIDE MICROMETERS
OUTSIDE MICROMETERS
Inside micrometers are used to measure an inside diameter to an accuracy of .001 of an inch. ID micrometers have a range of .500 when used with one-half inch spacers. (For remaining one-half inch, see page 7-3.)
DEPTH MICROMETERS
Outside micrometers are used to measure an outside distance or diameter to an accuracy of .001 of an inch.
Depth micrometers are used to measure depths to an accuracy of .001 inches.
SELECTING THE PROPER MICROMETER

The types of micrometers commonly used are made so that the longest movement possible between the spindle and the anvil is 1 inch. This movement is called the range. The frames of micrometers, however, are available in a wide variety of sizes, from 1 inch up to as large as 24 inches. The range of a 1 inch micrometer is from 0 to 1 inch. In other words, it can be used to work where the part to be measured is 1 inch or less. A 2-inch micrometer has a range from 1 inch to 2 inches, and will measure only work between 1 and 2 inches thick. A 6-inch micrometer has a range from 5 to 6 inches, and will measure only work between 5 and 6 inches thick. It
7-2
TM 9-243
SELECTING THE PROPER MICROMETER - Continued

is necessary, therefore, that the mechanic first find the approximate size of the work to the nearest inch, and then select a micrometer that will fit it. For example, to find the exact diameter of a piece of round stock use a rule and find the approximate diameter of the stock. If it is found to be approximately 3-1/4 inches, a micrometer with a 3- to 4-inch range would be required to measure the exact diameter. Similarly, with inside and depth micrometers, rods of suitable lengths must be fitted into the tool to get the approximate dimension within an inch, after which the exact measurement is read by turning the thimble. The size of a micrometer indicates the size of the largest work it will measure.
7-3
TM 9-243
READING A STANDARD MICROMETER
Reading a micrometer is only a matter of reading the micrometer scale or counting the revolutions of the thimble and adding to this any fraction of a revolution. The micrometer screw has 40 threads per inch. This means that one complete and exact revolution of the micrometer screw (1) moves the spindle (2) away from or toward the anvil (3) exactly 1/40 or 0.025 inch.
TO READ A MEASUREMENT AS SHOWN ABOVE. Read highest figure visible on barrel (5) . . . . . . . . . . . . . . . . 2 = 0.200 in. Number of lines visible between the No. 2 and thimble edge (6) . . . . . . . . . . . . . . . . . . . 1 = 0.025 in. The line on the thimble that coincides with or has passed the revolution or long line in the barrel (7) . . . . . . . . . . . . . . . . . . 16 = 0.016 in. TOTAL = 0.241 in.
The lines on the barrel (4) conform to the pitch of the micrometer screw (1), each line indicating 0.025 inch, and each fourth line being numbered 1, 2, 3, and so forth. The beveled edge of the thimble is graduated into 25 parts, each line indicating 0.001 inch, or 0.025 inch covered by one complete and exact revolution of the thimble. Every fifth line on the thimble is numbered to read a measurement in thousandths of an inch.
7-4
TM 9-243
READING A VERNIER MICROMETER

Reading the vernier micrometer is the same as reading the standard micrometer. An additional step must be taken, to add the vernier reading to the dimensions. This allows for precise measurements which are accurate to ten-thousandths (0.0001) of an inch. This scale furnishes the fine readings between the lines on the thimble rather than making an estimate as you would on a standard micrometer.
TO READ A MEASUREMENT AS SHOWN ABOVE: The ten spaces on the vernier (1) are equivalent to 9 spaces on the thimble (2). Therefore, each unit on the vernier scale is equal to 0.0009 inch and the difference between the sizes of the units on each scale is 0.0001 inch. Read highest figure visible on barrel (3). . . . . . . . . . . . . . . 2 = 0.200 in. Number of lines visible between the No. 2 and thimble edge (4). . . . . . . . . . . . . . . . . 3 = 0.075 in. The line on the thimble that coincides with or is nearest the revolution or long line in the barrel (5) . . . . . . . . . . . . . . . 11 = 0.011 in. The line on the vernier scale that coincides with the line on the thimble (6) . . . . . . . . . . . . . . . . . . . . . . .2 = 0.0002 in. TOTAL = .2862 in.
7-5
TM 9-243
READING A METRIC MICROMETER

The same principle is applied in reading the metric graduated micrometer, but the following changes in graduations are used: The pitch of the micrometer screw is 0.05 mm. One revolution of the spindle advances or withdraws the screw a distance equal to 0.5 mm.
TO READ MEASUREMENT AS SHOWN ABOVE: Read highest figure visible on barrel (1) . . . . . . . . . . . . . . 20 = 20.0 mm Number of lines visible between the No. 20 and thimble edge (2) . . . . . . . . . . . . . . . . . . .2 = 2.0 mm The line on the thimble that coincides with or has passed the revolution or long line in the barrel (3) . . . . . . . . . . . 36=36/100 (.36) mm NOTE Remember that 1 revolution is 0.5 mm. It takes 2 revolutions to move 1 mm. Measurement reading . . . . . . . . . . . TOTAL 22.36 mm
The barrel (1) is graduated in millimeters from 0 to 25. It takes two revolutions of the spindle to move the barrel 1 mm. The thimble (2) is graduated in 50 divisions with every fifth line being numbered. Rotating the thimble from one graduation to the next moves the spindle 1/50 of 0.5 mm, or 1/100 mm. Two graduations equal 2/100 mm, and so forth.
CARE OF MICROMETERS
1. 2. Coat metal parts of all micrometers with a light coat of oil to prevent rust. Store micrometers in separate containers provided by manufacturer. 3. 4. Keep graduations and markings on all micrometers clean and legible. Do not drop any micrometer. Small nicks or scratchescan cause inaccurate measurements.
7-6
TM 9-243
Chapter 8 RULES AND STEEL TAPES

The Types and Uses section provides you with a list of the types of rules and tapes. These pages should help you select the right rule or tape for the job. The Using Rules and Tapes section tells you how to use the various types of measuring instruments. The Care procedures tell you how to care for rules and tapes.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Folding rules . . . . . . . . . . . . . . . . . . . . . . . . Steel tapes . . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-2 8-2 8-2 8-2 8-3 8-3
8-1
TM 9-243
TYPES AND USES

The rule or tape is used for measuring where accuracy is not an extremely critical factor. They can be rigid or flexible, come in various lengths, and can be made of wood, metal, cloth, or fiberglass.
FOLDING RULES
RULES
The rule is the most common of measuring tools. This rule is usually 6 or 12 inches in length, although other lengths are available. Steel rules may be flexible or nonflexible, but the thinner the rule, the easier it is to measure accurately because the division marks are closer to the work.
These folding rules are usually from two to six feet long. The folding rules cannot be relied on for extremely accurate measurements because a certain amount of play develops at the joints after continued use.
STEEL TAPES
A rule usually has four sets of graduations, one on each edge of each side. The longest lines represent the inch marks. On one edge each inch is divided into 8 equal spaces so each space represents 1/8 in. The other edge of this side is divided in sixteenths. The 1/4-in. and 1/2-in. marks are commonly made longer than the smaller division marks to facilitate counting, but the graduations are usually not numbered individually, as they are sufficiently far apart to be counted without difficulty. The opposite side is similarly divided into 32 and 64 spaces per inch, and it is common practice to number every fourth division for easier reading.
There are many variations of the common rule. Sometimes the graduations are on one side only, sometimes a set of graduations is added across one end for measuring in narrow spaces, and sometimes only the first inch is divided into 64ths, with the remaining inches divided into 32nds and 16ths. A metal or wood folding rule may be used.
Steel tapes are made from 6 to about 300 feet in length.. The shorter tapes are made with a curved, but rigid, cross section flexible enough to be rolled up. Long, flat tapes need support over their full length to avoid sagging. Lack of support can cause reading errors. The most common types of steel tapes have a hook at one end to let one person take all the readings.
8-2
TM 9-243
USING RULES AND TAPES EXAMPLES
1 2 3 4 5 6 7
Rules and tapes used for measuring lengths. Measuring the outside diameter of pipe. Measuring the inside diameter of pipe. Measuring the circumference of pipe. Measuring inside dimensions. Measuring the thickness of stock through a hole. Measuring outside dimension with a tape.
CARE OF RULES AND TAPES

1. 2. Keep rules and tapes clean and dry. Store rules and tapes where they will not become bent or damaged.
8-3/(8-4 blank)
TM 9-243
Chapter 9 MISCELLANEOUS MEASURING TOOLS

The Types and Uses section provides you with a list of the more common types of miscellaneous measuring tools. These. pages should help you select the right measuring tool for the job. The Using section tells you how to use several of these tools for a certain application. Although there are many other uses for these tools, you should be able to perform most any task by becoming familiar with the procedures outlined in these pages. The Care procedures tell how to care for your measuring tools.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . Adjustable parallel . . . . . . . . . . . . . . . . . . . . V-block and clamp . . . . . . . . . . . . . . . . . . . . Angle plates . . . . . . . . . . . . . . . . . . . . . . . . . Magnetic base indicator holder . . . . . . . . . Registering speed indicators . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-2 9-2 9-2 9-2 9-2 9-2 9-3 9-3
9-1
TM 9-243
TYPES AND USES

ADJUSTABLE PARALLEL
plate is permanently jointed at a right angle. However, an adjustable type with varying angle adjustments is also available. Angle plates are used for clamping or holding work vertically. They are also used for layout, inspection, or machine set-up. Various sizes and designs are available depending on the task.
MAGNETIC BASE INDICATOR HOLDER

Adjustable parallels consist of two tapered parts fitted together. The distance between the two outside parallel surfaces varies by moving mating parts together or apart. This distance is then measured with a micrometer. Adjustable parallels are used as gages for leveling and setup work. Adjustable parallels are available in various sizes depending on the nature of work.
V-BLOCK AND CLAMP
The V-block and clamp assembly consists of a V-shaped, hardened steel body to support round, square, or rectangular shaped work. A clamp (or clamps) holds the work firmly in the body groove. V-blocks and clamps are especially used for grinding, milling, or drilling purposes. Various styles and designs of V-blocks and clamps are available depending on application.
The magnetic base indicator holder is a one-piece metal assembly that attaches to the work surface magnetically. A gage or indicator attaches to the assembly. Base indicator holders are used for attaching gages to lathes, milling machines, shapers, or any machine where graduations are difficult to read. Magnetic base indicator holders are available in many sizes and designs depending on application.
REGISTERING SPEED INDICATORS
ANGLE PLATES
Angle plates are devices consisting of two flat outside working surfaces jointed at right angles. The outside work surfaces are precision ground. The standard angle
Registering speed indicators are designed to count the number of revolutions of wheels, shafts, etc. Revolutions are counted by attaching spindle of speed indicator to hub of shaft or wheel. Indicator spindle will turn in either direction counting each revolution on a circular dial. Various designs of speed indicators are available depending on nature of use.
9-2
TM 9-243
USING MISCELLANEOUS MEASURING TOOLS

1 2 3 Place pipe (1) in V-blocks (2). Secure pipe (1) in position using screw clamps (3). Begin drilling at desired spot on pipe (1).
CARE OF MISCELLANEOUS MEASURING TOOLS

1. 2. 3. Clean all tools thoroughly after using. Apply a light coat of oil to all exposed metal parts to avoid rusting. To avoid possible damage to sensitive tools, store tools in proper locations.
9-3/(9-4 blank)
TM 9-243
Chapter 10 LEVELS
The Types and Uses section provides you with a list of types of levels. These pages should help you select the right level for the job. The Using Levels section tells you how to use levels for their various functions (plumbing, leveling, etc).
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . Master precision level . . . . . . . . . . . . . . . . Machinists level . . . . . . . . . . . . . . . . . . . . . Iron bench level . . . . . . . . . . . . . . . . . . . . . Striding level . . . . . . . . . . . . . . . . . . . . . . . . Carpenters level . . . . . . . . . . . . . . . . . . . . Line level . . . . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-2 10-2 10-2 10-2 10-2 10-2 10-2 10-3
10-1
TM 9-243
TYPES AND USES

Levels are tools designed to prove whether a plane or surface is in the true vertical or true horizontal. All levels consist of a liquid-filled glass tube or tubes supported in a frame.
STRIDING LEVEL
MASTER PRECISION LEVEL
The striding level is a machinists level which is mounted on a raised base. This level is used to span existing cabling, piping, or similar obstructions. It is extremely useful in a machine shop for checking the true horizontal of the flatway on a lathe. The master precision level has a ground and graduated main vial (1). The top and bottom of the level are milled and ground to make sure both surfaces are absolutely parallel. This level is used to determine the true horizontal with the main vial (1). The true vertical is determined by using the two smaller vials (2).
CARPENTERS LEVEL
MACHINISTS LEVEL
The carpenters level has three vials which are mounted horizontally (1) vertically (2) and at a 45 degree angle (3). The carpenters level is used in construction for checking for true vertical, true horizontal, and 45 degree angles.
The machinists level has an extra large vial. This increases its accuracy and sensitivity. Some of these levels have grooved bottoms which fit over pipes and shafts. They are used in machine shops for leveling work and equipment.
IRON BENCH LEVEL
Some levels have a bent tube (4) which allows the bubble to settle quickly.
LINE LEVEL
The iron bench level is made of a special design casting which insures its lightness, strength, and rigidity. It is used mostly in the construction industry. It may also be used in a machine shop.
The line level is a single vial in a metal case with a hook on each end for hanging on a cord. It is used to check whether two points are level, such as two points on a floor or in an elevation. It must be used with a tightly stretched cord.
10-2
TM 9-243
USING A LEVEL
A level may be checked for accuracy by placing it on a known level surface and noting the position of the bubble. Reverse the level end for end. Observe the position of the bubble. If the relative position of the bubble was the same for both readings, the level is accurate.
ANGLED SURFACE
HORIZONTAL SURFACE
Place the level on a flat horizontal surface. Check the horizontal vial (1). The bubble should be between the two etched lines on the vial. If it is not, the surface is not horizontal.
Place the level on an angled surface. If the angle is 45 degrees, the bubble will appear between the notched lines on the 45 degree vial (2).
VERTICAL SURFACE
Place the level against a flat vertical surface. Check the vertical vial (3). The bubble should be between the two etched lines on the vial. If it is not, the surface is not vertical.
10-3/(10-4 blank)
TM 9-243
Chapter 11 PLUMB BOBS

The Types and Uses pages provide you with a list of the more common types of plumb bobs. These pages should help you select the right plumb bob for the job. The Using Plumb Bobs pages tell you how to use a steel plumb bob to establish the true vertical of a square
post. By becoming familiar with this procedure you will build a good background for using other plumb bobs. The Care page tells you how to keep your plumb bobs in proper condition.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . Surveyors Polished Brass . . . . . . . . . . . . Solid Steel . . . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-2 11-2 11-2 11-3 11-6
11-1
TM 9-243
TYPES AND USES

PLUMB BOBS
A plumb bob is a precision instrument used to establish a true vertical transfer and line-up reference point, and to take readings or soundings in tanks and voids. Plumb bobs are used by carpenters, surveyors and maintenance technicians. SOLID STEEL
SURVEYOR'S POLISHED BRASS
The surveyors brass plumb bob may be either a spool type (A) or an adjustable cap type (B). Both types have replaceable steel points for increased accuracy. The adjustable cap allows the operator to make minor corrections to height and rotation to make sure the bob hangs straight. The surveyors brass plumb bob comes with a minimum of 7 feet of nylon, silk or linen cord. It comes in 6, 8, 10, and 16 ounce sizes. The heavier plumb bobs are better for use in windy areas.
The solid steel plumb bob (A) may have a machined integral head, body, and point. It may have just a removable head (B), or a removable head and a replaceable point (C). It may be round or hexagonal in shape and it comes in 3, 8, and 12 ounce sizes. Cord for the solid steel bobs must be obtained from a separate source. This type plumb bob is used when extreme accuracy is not required.
11-2
TM 9-243
USING A PLUMB BOB

NOTE The practice procedure which follows (for establishing the true vertical of a post) uses a plumb bob with a removable head.
Install cap into plumb bob body (4).
The first step is to attach the cord as follows:
Insert a string or cord (1) into the cap (2) of the plumb bob. Make sure the cord will support the plumb bob. Pull the cord through the cap.
Tighten cap securely in the body and suspend the plumb bob by the cord only. Make sure the knot will support the plumb bob.
2 Place cap in the palm of your hand and tie an

overhand knot (3) in the cord. Pull the cord drawing the knot against cap base. Make sure the knot is not too large or tied at an angle which would affect the hanging of the plumb bob.
11-3
TM 9-243
USING A PLUMB BOB - Continued

NOTE The following task is not the only use of a plumb bob. NOTE Post hole must be dug and an assistant is required before starting the task.
Hang string and plumb bob so they extend over end of ruler and the plumb bob is just above the ground surface.
Place a ruler (5) on the top of the post (6) so that it extends 2 inches beyond an edge.
11-4
TM 9-243
USING A PLUMB BOB - Continued
Have the assistant measure distance (7) from post to string just above the plumb bob. It should read 2 inches. If it doesnt, move the base or the top of the post right or left until you get a 2-inch reading on both rules. When extreme accuracy is desired, measurement would be taken to the point of the plumb bob (8). Repeat steps 5, 6, and 7 on side 2.
11-5
TM 9-243
CARE OF PLUMB BOBS

Handle plumb bobs with care. Do not use a plumb bob as a hammer or lever. Lightly coat plumb bobs with lubricating oil for short periods of storage. For long-term storage, apply a heavy coat of oil and wrap the plumb bob in oil-soaked paper. Store plumb bobs in a protective box in a dry place. Make certain threads of removable caps (1) and points (2) are lightly coated with lubricant and placed in a protective box.
11-6
TM 9-243
Chapter 12 SCRIBERS
The Types and Uses section provides you with a list of the types of scribers. These pages should help you select the right scriber for the job.
The Using Scribers section tells you how to use the scriber to scribe an orientation mark. The Care procedures tell you how to care for the scribers.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . 12-2 Machinists scribers . . . . . . . . . . . . . . . . . . 12-2 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
12-1
TM 9-243
TYPES AND USES

MACHINISTS SCRIBERS
The machinists scriber is used to mark or score on steel, glass, aluminum, copper or similar surfaces. There are two basic types of machinists scribers, single point pocket (1) and bent point-straight point (2). The bent point is used to scribe through holes or other hard to reach places.
Tungsten carbide tips have extremely hard points and are used on hardened steel or glass.
USING A MACHINISTS SCRIBER

NOTE The following procedure for scribing an alignment mark on a telescope is not the only use of a scriber.
Place material to be marked on a firm surface. Place a steel rule or straight edge (1) on the work beside the line to be scribed.
Use finger tips of one hand to hold the straight edge securely. Hold the scriber in your hand as you would a pencil.
12-2
TM 9-243
USING A MACHINISTS SCRIBER - Continued
Scribe the line by drawing the scriber (2) along the straight edge at a 45 degree angle and tipped in the direction it is being moved.
CARE OF SCRIBERS
Stow on a rack or in a box. Do not use scribers for other than intended purposes.
Protect points by reversing them in the handle or placing a cork or a piece of soft wood over point. Keep the scribers clean and lightly oiled.
12-3/(12-4 blank)
TM 9-243
Chapter 13 SQUARES
The Types and Uses section provides you with a list of the types of squares. These pages should help you select the right square for the job.
The Using Squares section tells you how to use a square to perform its various functions. The Care procedures tell you how to care for squares.
INDEX
/tem Page
TYPES AND USES . . . . . . . . . . . . . . . . . . Carpenters square . . . . . . . . . . . . . . . . . . Try square . . . . . . . . . . . . . . . . . . . . . . . . . . Combination square . . . . . . . . . . . . . . . . . Sliding T-bevel . . . . . . . . . . . . . . . . . . . . . . Bevel protractor . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13-2 13-2 13-3 13-3 13-4 13-4 13-4 13-8
13-1
TM 9-243
TYPES AND USES

CARPENTERS SQUARE
The octagon or eight square scale is used for cutting an octagon from a square piece of material. The back side contains the hundredths scale and is divided into tenths, twelfths, and sixteenths as shown. There are two tables down the center.
The carpenters square is made up of two parts: the body or blade, and the tongue. It has inches divided into eighths, tenths, twelfths, and sixteenths. The face side contains the manufacturers name and the inches are divided into eighths and sixteenths as shown. There are two tables down the center.
The essex board measure is used to compute the number of board feet in a given piece of lumber.
The rafter table is used for determining the length and cut of rafters.
The brace measure is used to find the exact lengths of common braces.
13-2
TM 9-243

The following scales or inch divisions are found on the carpenters square: outside edge inches and sixteenths Face of body inches and eighths inside edge Face of body Face of tongue outside edge inches and sixteenths inches and eighths Face of tongue inside edge outside edge inches and twelfths Back of body inches and sixteenths Back of body inside edge Back of tongue outside edge inches and twelfths inches and tenths Back of tongue inside edge
COMBINATION SQUARE
TRY SQUARE
The combination square is made up of the following components: 1. A slotted 12-inch stainless steel rule (1) which is graduated in eighths, sixteenths, thirty-seconds, and sixty-fourths of an inch. It can be used as a measuring scale by itself or with any one of the following components. 2. The center head (2) when attached to the rule, bisects a 90 degree angle. Its used for determining the center of cylindrical work. The protractor (3) has a level (4) and a revolving turret (5) which is graduated in degrees from 0 to 180 or 0 to 90 in either direction. It is used to lay out and measure angles to within one degree. The square head (6) has a level (7), a scribe (8), and 45 degree (9) and 90 degree sides (10). It is used to lay out 45 and 90 degree angles and to check level. It may also be used as a height or depth gage.
The try square is made of a steel or wood stock (1) and a blade (2). The blade is from 2 to 12 inches long and is graduated in eighths. The try square is used to set or check lines which are at right angles (90 degrees) to each other.
3.
4.
13-3
TM 9-243

SLIDING T-BEVEL BEVEL PROTRACTOR
The sliding T-bevel is made up of a slotted blade (1) and a solid stock (2). The blade is adjustable so it can be set to measure any angle. The T-bevel is used for testing bevels and laying out angles.
The bevel protractor is made up of an adjustable blade (1) and a graduated dial (2) which contains a vernier scale. The bevel protractor is used to establish an angle and determine its relationship to other surfaces. The acute angle attachment (3) is used for measuring acute angles accurately.
USING A CARPENTERS SQUARE TO MARK A SQUARE LINE
1 To mark a square line, place the blade or tongue (1)

of the square against the side of the material with the square tilted slightly so the blade or tongue of the square extends across the work.
Mark a line across the work using a pencil or marking crayon.
USING A CARPENTERS SQUARE TO LAY OUT STEPS

1 The following example shows proper square position when marking cut lines for a series of steps 9 x 12.
2 Continue the process until desired number of steps

has been layed out.
13-4
TM 9-243
USING A TRY SQUARE
2 1
To check a square joint, place the stock (I) against a horizontal section and the blade (2) against a vertical section. Light must not be seen around blade edge. If light is seen, the work is not square.
To check the end of a board, place stock on vertical edge and extend blade over the end. Light must not be seen around blade edge. If light is seen, the work is not square.
USING A SLIDING T-BEVEL SQUARE
2 1
Loosen locking nut (1) and adjust blade (2) to measure a desired angle using protractor (3). Tighten locking nut (1).
The angle may now be laid out by extending the blade across the board with the stock (4) held firmly against the edge.
13-5
TM 9-243
USING A SLIDING T-BEVEL SQUARE - Continued

3
Mark with a pencil or marking crayon. Make sure the square does not move while marking.
USING A COMBINATION SQUARE

Using as a center head to find the diameter of a cylinder:
Slide center head (1) on rule (2) and fasten by tightening setscrew (3).
Mark the diameter on the cylinder using a pencil or marking crayon by drawing a straight line along the inside edge (4). Make sure the square does not slip while marking.
Put the center head flush against the cylinder.
13-6
TM 9-243
USING A COMBINATION SQUARE - Continued

Using as a protractor head to determine an angle:
4 Remove and read measured angle on protractor

scale. Using as a combination square to determine depth:
1 Slide protractor head (1) on rule (2) and fasten by

tightening setscrew (3).
1 Slide square head (1) on rule (2) and fasten by

tightening setscrew (3). Loosen the protractor adjustment screws (4) so the protractor may be pivoted about the rule. Angle being measured is already marked.
Loosen setscrew.
Place the rule on the angle being measured and pivot the protractor head against the edge. Tighten adjustment screws.
Set the flat surface of the square head (1) above the hole and adjust the rule (2) until it hits the bottom.
13-7
TM 9-243
USING A COMBINATION SQUARE - Continued
Remove the combination square and read the depth at the intersection of the rule and the square head (4).
4 Tighten setscrew (3).
CARE OF SQUARES
Make sure squares are kept clean. Apply a light coat of oil to all metal surfaces after using. A square with a loose stock is no good. Replace the square.
13-8
TM 9-243
Chapter 14 SURFACE, DEPTH, AND HEIGHT GAGES

The Types and Uses section provides you with a list of the types of gages. These pages should help you select the right gage for the job. The Using section tells you how to use the gages for their intended purposes. The Care procedures tell you how to keep your gages in good condition. INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . Surface gage . . . . . . . . . . . . . . . . . . . . . . . Depth gage . . . . . . . . . . . . . . . . . . . . . . . . Height gage . . . . . . . . . . . . . . . . . . . . . . . . Surface plate . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-2 14-2 14-2 14-3 14-3 14-4 14-5
14-1
TM 9-243
TYPES AND USES

SURFACE GAGE
marks (1) located on the sliding head (2). The rule depth gage is a graduated rule (3) with a sliding head (2) designed to bridge a hole or slot. The gage holds the rule at a right angle to the surface when taking measurements. This type has a measuring range of 0 to 5 inches. The sliding head has a clamping screw so that it may be clamped in any position. The sliding head is flat and perpendicular to the axis of the rule. It ranges in size from 2 to 2-5/8 inches wide and from 1/8 to 1/4 inch thick.
MICROMETER DEPTH GAGE
A surface gage is a measuring tool used to transfer measurements to work by scribing a line, and to indicate the accuracy or parallelism of surfaces. The surface gage consists of a base with an adjustable spindle (1) to which may be clamped a scriber or an indicator (2). Surface gages are made in several sizes and are classified by the length of the spindle. The smallest spindle is 4 inches long, the average 9 to 12 inches, and the largest 18 inches. The scriber is fastened to the spindle with a clamp. The bottom and the front end of the base of the surface gage have deep V-grooves. The grooves allow the gage to measure from a cylindrical surface. The base has two gage pins (3). They are used against the edge of a surface plate or slot to prevent movement or slippage.
RULE DEPTH GAGE
The micrometer depth gage consists of a flat base (1) that is attached to the barrel of a micrometer head (2). These gages have a range from 0 to 9 inches, depending on the length of extension rod used. The hollow micrometer screw has a 1/2 or 1 inch range. Some are provided with a ratchet stop. The flat base ranges in size from 2 to 6 inches. Several extension rods are supplied with this type gage: NOTE For additional information on micrometers, see chapter 7 in this manual.
A rule depth gage measures the depth of holes, slots, counterbores, and recesses. Some rule depth gages, such as the one shown above, can also be used to measure angles. This is done by using the angle
14-2
TM 9-243

VERNIER DEPTH GAGE HEIGHT GAGE
A height gage is used in the layout of jigs and fixtures. On a bench, it is used to check the location of holes and surfaces. It accurately measures and marks off vertical distances from a plane surface. The vernier depth gage consists of a graduated scale (1) either 6 or 12 inches long. It also has a sliding head (2) similar to the one on the vernier caliper. (See chapter 6, Using Vernier Caliper). The sliding head is designed to bridge holes and slots. The vernier depth gage has the range of the rule depth gage. It does not have quite the accuracy of a micrometer depth gage. It cannot enter holes less than 1/4 inch in diameter. However, it will enter a 1/32-inch slot. The vernier scale is adjustable and may be adjusted to compensate for wear. The vernier height gage is a caliper with a special base (1) to adapt it for use on a surface plate. Height gages are available in several sizes. Most common are the 10, 18, and 24-inch gages in English measure. The most common metric gages are the 25 and 46-centimeter sizes. Height gages are classified by the dimension they will measure above the surface plate. Like the vernier caliper (see chapter 6, Reading a Vernier Caliper), height gages are graduated in divisions of 0.025 inch. Its vernier scale is divided into 25 units for reading thousandths of an inch.
DIAL DEPTH GAGE SURFACE PLATE
Dial depth gages are for rapidly checking depths of holes, recesses, slots, scratches, and paint thicknesses. It should be noted that measurements made with depth gages should be on a longitudinal axis. The depth gage will give direct readings on the dial in half-thousands of an inch (0.0005 in.); press the push button down until the measuring rod contacts the work and read the depth on the dial.
A surface plate provides a true, smooth, planesurface. It is often used as a level base for surface and height gages from which to make accurate measurements. Surface plates are usually made of close grained cast iron (1), are rectangular in shape, and come in a variety of sizes. Change 1 14-3
TM 9-243
USING THE SURFACE, DEPTH, AND HEIGHT GAGES

Below are examples of how each of the gages mentioned in this chapter can be used.
USING A VERNIER DEPTH GAGE
USING A SURFACE GAGE
Measuring hole depth of die from a given surface.
USING A DIAL DEPTH GAGE

Setting gage for transfer of 4-inch vertical measurement.
USING A RULE DEPTH GAGE
Measuring depths of holes, recesses, slots, scratches, and paint thicknesses.
Measuring the distance from a surface to a recessed point.
USING A MICROMETER DEPTH GAGE
USING A HEIGHT GAGE
Measuring projection depth with micrometer precision. Change 1
Measuring vertical distance from a plane surface.
14-4
TM 9-243
CARE OF SURFACE, HEIGHT, AND DEPTH GAGES

1. 2. Coat all metal parts of gages with a light coat of oil to prevent rust. Carefully store gages when not in use. Use separate containers if provided by manufacturer. 3. 4. 5. Keep graduations and markings clean and legible. Do not drop any gage. Small nicks and scratches can cause inaccurate measurements. Protect all pointed gage parts from damage.
14-5/(14-6 blank)
TM 9-243
Chapter 15 RING AND SNAP GAGES AND GAGE BLOCKS

The Types and Uses section provides you with a list of the types of gages. These pages should help you select the right gage for the job.
The Using section tells you how to use the gages to make a measurement. The Care procedures tell you how to care for the gages.
INDEX
item Page
TYPES AND USES. . . . . . . . . . . . . . . . . . Ring gages . . . . . . . . . . . . . . . . . . . . . Snap gages . . . . . . . . . . . . . . . . . . . . . . Gage blocks . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15-2 15-3 15-3 15-4 15-4 15-9
15-1
TM 9-243
TYPES AND USES

Ring and snap gages and precision gage blocks are used as standards to determine whether or not one or more dimensions of a manufactured post are within specified limits. Their measurements are included in the construction of each gage, and they are called fixed gages. However, some snap gages are adjustable. Gages are used for a wide range of work, from rough machining to the finest tool and die making. The accuracy required of the same type of gage will be different, depending on the use.
SNAP GAGE - ADJUSTABLE
RING GAGES
SNAP GAGE - NONADJUSTABLE
GAGE BLOCKS
The following classes of gages and their limits of accuracy are standard for all makes: Class X - Precision lapped to close tolerances for many types of masters and the highest quality working and inspection gages. Class Y - Good lapped finish to slightly increased tolerances for inspection and working gages. Class Z - Commercial finish (ground and polished, but not fully lapped) for a large percentage of working gages in which tolerances are fairly wide, and where production quantities are not so large. Class ZZ - (Ring gages only). Ground only to meet the demand for an inexpensive gage, where quantities are small and tolerances liberal.
The table below lists the tolerances for ring gages in each class:
TO AND INCL ABOVE 0.029 0.825 0.825 1.510 1.510 2.510 2.510 4.510 4.510 6.510 6.510 9.010 9.010 12.010 X 0.00004 0.00006 0.00008 0.00010 0.00013 0.00016 0.00020 Y 0.00007 0.00009 0.00012 0.00015 0.00019 0.00024 0.00030 Z 0.00010 0.00012 0.00016 0.00020 0.00025 0.00032 0.00040 RING GAGES ZZ 0.00020 0.00024 0.00032 0.00040 0.00050 0.00064 0.00080
X Precision lapped Y Lapped Z Ground or polished (grinding marks may be in evidence), ZZ Ground only
15-2
TM 9-243
TYPES AND USES

RING GAGES SNAP GAGES
The plain snap gage is made in two general types, the nonadjustable and adjustable. The nonadjustable type is a solid construction, having two gaging members, GO (1) and NO GO (2) as shown above. The part to be inspected is first tried on the GO side and then the gage is reversed and the part tried on the NO GO side. Some solid snap gages (3) have combined gaging members in the same set of jaws as shown above, known as a progressive snap gage. The outer member (4) gages the GO dimension and the inner member (5) the NO GO dimension.
The plain ring gage is an external gage of circular form. For sizes between 0.059 and 0.510 inch, ring gages are made with a hardened bushing pressed into a soft body. The thickness of the gage will range from 3/16 to 1-5/16 inches. On ring gages, the GO gage (1) is larger than the NO GO gage (2). The GO and NO GO ring gages are separate units. They can be distinguished from each other by an annular groove (3) cut in the knurled outer surface of the NO GO gage. Ring gages made for diameters of 0.510 to 1.510 inches are the same as those shown above, except there is no bushing; they are made all in one piece. Ring gages, sized from 1.510 to 5.510 inches are made with a flange (4). This design reduces the weight, making the larger sizes easier to handle.
Three standard designs of the adjustable type are available, consisting of a light, rigid frame with adjustable gaging pins, buttons, or anvils. These pins or buttons may be securely locked in place after adjustment, and locking screws are tightened to hold the gaging dimensions. One type of adjustable snap gage is made in sizes that range from 1/2 to 12 inches (1). It is equipped with four gaging pins and is suitable for checking the dimension between surfaces. Another type is made in sizes that range from 1/2 to 11-1/4 inches (2). It is equipped with four gaging buttons and is suitable for checking flat or cylindrical work. The third type is made in sizes from 1/2 to 11-5/8 inches (3). It is equipped with two gaging buttons and a single block anvil, and is especially suitable for checking the diameters of shafts, pins, studs, and hubs.
Ring gages are used more often in the inspection of finished parts than parts in process. The reason for this is that the finished parts are usually readily accessible; whereas, parts in a machine that are supported at both ends would have to be removed to be checked.
15-3
TM 9-243

Gage blocks are available in sets of from 5 to as many as 85 blocks of different dimensions. Precision gage blocks are made from a special alloy steel. They are hardened, ground, and then stabilized over a period of time to reduce subsequent waxing. They are rectangular in shape with measuring surfaces on opposite sides. The measuring surfaces are lapped and polished to an optically flat surface and the distance between them is the measuring dimension. This dimension may range from 0.010 inch up to 20 inches.
USING A RING GAGE

To check the shank diameter of a pivot stud.
Line the stud (1) up with the hole (2) and press in gently. If the stud will not go in, the shank is too large. If it will go in, the stud is not oversize.
After checking the part in the GO gage, check it in the NO GO gage. The stud must not enter this gage to establish it as being between the desired limits. NOTE The GO ring gage controls the maximum dimension of a part and NO GO plug gages control the minimum dimension of a hole. Therefore, GO gages control the tightness of fit of mating parts and NO GO gages control the looseness of fit of mating parts.
With the stud in the hole, check the piece for taper and out-of-roundness by sensing any wobble.
15-4
TM 9-243
USING AN ADJUSTABLE SNAP GAGE

Before an adjustable snap gage can be used to check parts, the GO and NO GO buttons, pins, or anvils must be set to the proper dimensions.
1 The snap (1) gage must first be clamped in a holder.

NOTE Adjust the GO dimension first as shown in the illustration, or if desired, reverse the procedure and adjust the NO GO dimension first.
Loosen the locking screw (2) and turn the adjusting screws (3) until the dimensions (4) is set. NOTE The desired dimension may be taken from a master disk, a precision gage block, or a master plug.
3 4 5
Turn the other adjusting screw (3) until the NO GO dimension (5) is set. After adjusting for proper dimensions with the master precision piece (6) in place, tighten the locking screws (2). Recheck to make sure the dimensions have not changed before using the gage.
15-5
TM 9-243
USING AN ADJUSTABLE SNAP GAGE - Continued

GAGING FLAT PARTS
4 1
Position gage so that the pins or buttons (1) are square with the flat surfaces on the part (2).
If the part is undersize, it will be possible to push it past the NO GO pins.
GAGING CYLINDRICAL PARTS
2 Using a slight hand pressure, push the gage (3)

over the part.
Locate the gage on the part with the solid anvil (1) on top. Rock the gage (2) as indicated by the shaded segment above, where the GO dimension is checked.
3 If the part is within limits, the NO GO pins will stop

the part.
2 If the shaft is not oversized, the first button (3) will

pass over it easily.
15-6
TM 9-243
USING AN ADJUSTABLE SNAP GAGE - Continued
Move the gage to the position shown above. If the NO GO button (4) stops the gage, the shaft is within limits.
If the gage can be rocked further to the position, as shown, the part diameter is too small, since it has passed the NO GO button.
HOW TO USE PRECISION GAGE BLOCKS

Before using gage blocks, remove the coat of rustpreventive compound with a chamois or a piece of cleansing tissue or by cleaning with an approved solvent. Gage blocks and any measuring tool used with them must be free of grease, oil, dirt, and other foreign matter to avoid a lapping action whenever the block is moved, and to ensure accurate measurement. When using gage blocks, take particular care when measuring hardened work to avoid scratching the measuring surfaces.
NOTE When building gage blocks (wringing them together) to obtain a desired dimension, care should be exercised to avoid damaging them.
1 Bring the blocks together flat and move them

slightly back and forth. This minimizes scratching, as it will detect any foreign particles between the surfaces.
15-7
TM 9-243
USING PRECISION GAGE BLOCKS - Continued

4
Shift gage blocks so that their sides are in line. Any combination of gage blocks may be stacked together in this manner. The combination will be as solid as a single block. NOTE The adhesive force that binds two gage blocks together is a combination of molecular attraction and the suction cup action due to the film of oil or moisture on the surfaces wrung together. Separate gage blocks by sliding them apart, using the same movement as when wringing them together.
2 3
Shift the blocks. If the blocks are clean, they will begin to take hold. Slide the two blocks together, using a slight pressure and a rotary motion.
CAUTION Do not leave blocks wrung together for long periods of time since surfaces in contact will tend to corrode.
FACTORS TO CONSIDER WHEN USING GAGE BLOCKS

Ordinary changes in temperature have a sizable effect on measurements made with precision gage blocks. The standard measuring temperature is 68F, which is just a little lower than the average temperature in most shops. Since the room temperature affects the work as well as the block, the expansion in the work will be matched in most cases by a similar expansion in the block. The coefficient of linear expansion of several metals and blocks is listed below:
Material Millionths of an inch
When using gage blocks consider the source of error resulting from temperature. Metals other than iron and steel (such as aluminum) have a much different coefficient of linear expansion which will result in a difference between the room temperature measurement and the standard measuring temperature measurement. Careless handling of gage blocks may produce an error of several millionths of an inch and this error increases proportionally with the dimension of the block. The temperature of the work may be either lower or higher than the room temperature as a result of a machining operation and this difference may be sufficient to cause a sizable error. Theoretically, the measuring pressure should increase proportionally with the area of contact. For practical purposes, it is better to use a standard measuring pressure. The most commonly used pressure is 1/2 to 2 pounds. Gage blocks are used in the layout and in checking the accuracy of tools, dies, and fixtures. They are also used in machine setups and in checking parts in process of manufacture and finished parts. Gage blocks are commonly used in setting adjustable instruments and indicating gages and verifying inspection gages. Gage blocks are used to verify the accuracy and wear of ring and snap gages and many other special-purpose gages. The classification of blocks depends largely on the accuracy required. Typical classification is shown on the following page.
Steel Iron Phosphor bronze Aluminum Copper Gage blocks
5.5 to 7.2 per degree F 5.5 to 6.7 9.3 12.8 9.4 6.36 to 7.0
Handle blocks only when they must be moved and hold them between the tips of your fingers so that the area of contact is small. Hold them for short periods of time only. NOTE Avoid conducting body heat into the block by careless handling. Body heat may raise the temperature of the block, causing a serious error in a measurement, particularly if a long stack of blocks is being handled.
15-8
TM 9-243
FACTORSTO CONSIDER WHEN USING GAGE BLOCKS - Continued

C/ass Work Error range millionths of an inch Class Work Error range millionths of an inch
II
Verifying gages, setting instruments, and tool inspection. Layout of jigs, fixtures and dies, setting instruments, and tool inspection.
5 to 20
III
Setup of grinding, milling and drill machines, and parts inspection.
40 to 100
20 to 40
CARE OF RING AND SNAPGAGES

2
Always consider the abrasive action of the part on the gage. Cast iron, steel, and cast aluminum are more abrasive than brass, bronze, and nonmetals such as plastics. Use particular care when gaging cast iron, steel, and cast aluminum. When gages are stored, arrange them neatly in a drawer or case so that they do not contact other tools or each other. Always hold the gages in your hands when checking. Never clamp them in a vise. At frequent intervals, check all gages for accuracy and wear with gage blocks or master gages.
3 4
1 Always make certain that the surfaces of the parts

gaged and the gage itself are kept free from abrasives, dirt, grit, chips, and all foreign matter.
CARE OF GAGE BLOCKS
1.
Observe particular care when using gage blocks to measure hardened work. The danger of scratching is increased when the work is as hard as the block, or harder. Never touch the measuring surfaces of blocks any more than necessary. The moisture from your hands contains an acid which, if not removed, will eventually. stain the blocks.
3. 4.
Before using blocks, ensure there is no grease, oil, dirt, or any foreign substances on block. Every time a set of blocks is used, all the blocks which have been cleaned for use must be covered with a film of acid-free oil, such as boiled petrolatum, before they are put away. Wipe them with an oiled chamois as you return the blocks to their places in the case.
2.
15-9/(15-10 blank)
TM 9-243
Chapter 16 MISCELLANEOUS MEASURING GAGES

The Types and Uses section provides you with a list of miscellaneous measuring gages. These pages should help you select the right gage for the job. The Using section tells you how to use the miscellaneous measuring gages to perform the measuring operation. The Care procedures tell you how to care for the gages.
INDEX
Item
Page
TYPES AND USES . . . . . . . . . . . . . . . . . . Thickness (feeler) gages . . . . . . . . . . . . . Center gage . . . . . . . . . . . . . . . . . . . . . . . . Screw pitch gages . . . . . . . . . . . . . . . . . . . Small hole gage set . . . . . . . . . . . . . . . . . Telescoping gages . . . . . . . . . . . . . . . . . . Thread cutting tool gages . . . . . . . . . . . . Fillet and radius gages . . . . . . . . . . . . . . . Drill point gage . . . . . . . . . . . . . . . . . . . . . . Wire gages . . . . . . . . . . . . . . . . . . . . . . . . . Drill gages . . . . . . . . . . . . . . . . . . . . . . . . . . Marking gages . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thickness gage . . . . . . . . . . . . . . . . . . . . . Center gage . . . . . . . . . . . . . . . . . . . . . . . . Screw pitch gage . . . . . . . . . . . . . . . . . . . . Small hole gage . . . . . . . . . . . . . . . . . . . . . Telescoping gage . . . . . . . . . . . . . . . . . . . Thread cutting tool gage . . . . . . . . . . . . . Fillet and radius gage . . . . . . . . . . . . . . . . Drill point gage . . . . . . . . . . . . . . . . . . . . . Wire gage . . . . . . . . . . . . . . . . . . . . . . . . . Drill gage . . . . . . . . . . . . . . . . . . . . . . . . . . . Marking gage . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16-2 16-2 16-2 16-3 16-3 16-3 16-4 16-4 16-4 16-4 16-5 16-5 16-5 16-5 16-6 16-6 16-6 16-7 16-7 16-7 16-8 16-8 16-8 16-9 16-9
16-1
TM 9-243
TYPES AND USES

THICKNESS (FEELER) GAGES
gages are also available in single blades and in strip form for specific measurements. For convenience, many groups of thickness gages are equipped with a locking screw in the case that locks the blade to be used in the extended position. These gages are fixed in leaf form, which permits the checking and measuring of small openings such as contact points, narrow slots, and so forth. They are widely used to check the flatness of parts in straightening and grinding operations and in squaring objects with a try square.
CENTER GAGE
Thickness (feeler) gages are made in many shapes and sizes; usually 2 to 26 blades are grouped into one tool and graduated in thousandths of an inch. Most thickness blades are straight, while others are bent at the end at 45 degree and 90 degree angles. Some thickness gages are grouped so that there are several short and several long blades together. Thickness
The center gage is graduated in 14ths, 20ths, 24ths, and 32nds of an inch. The back of the center gage has a table giving the double depth of thread in thousandths of an inch for each pitch. This information is useful in determining the size of tap drills. Sixty-degree angles in the shape of the gage are used for checking Unified and American threads as well as for older American National or U.S. Standard threads and for checking thread cutting tools.
16-2
TM 9-243

SCREW PITCH GAGES SMALL HOLE GAGE SET
Small hole gages are adjustable, having a rounded measuring member. A knurled screw in the end of the handle is turned to expand the ball-shaped end in small holes and recesses. A micrometer caliper is used to measure the ball end. Maximum measuring capacity is 1/2 inch. This set of 4 or more gages is used to check dimensions of small holes, slots, grooves, and so forth from approximately 1/8 to 1/2 inch in diameter.
TELESCOPING GAGES
Screw pitch gages are made for checking the pitch of U.S. Standard, Metric, National Form, V-form, and Whitworth cut threads. These gages are grouped in a case or handle, as are the thickness gages. The number of threads per inch is stamped on each blade. Some types are equipped with blade locks. The triangularshaped gage has 51 blades covering a wide range of pitches, including 11-1/2 and 27 threads-per-inch for V-form threads. Screw pitch gages are used to determine the pitch of an unknown thread. The pitch of a screw thread is the distance between the center of one tooth to the center of the next tooth.
Telescoping gages are used to gage larger holes and to measure inside distances. These gages are equipped with a plunger (1) that can be locked in the measuring position by a knurled screw (2) in the end of the handle (3). Maximum measuring capacity is 6 inches. Measurements must be calipered on the gage by a micrometer, as in the case of the small hole gages. They are also used when measurements cannot be taken with a standard micrometer. Telescoping gages are particularly adaptable for roughly bored work and odd sizes and shapes of holes. Compress the plungers and lock them by turning handle screw.
16-3
TM 9-243

THREAD CUTTING TOOL GAGES DRILL POINT GAGE
Thread cutting tool gages are hardened steel plates with cutouts around the perimeter. Each cutout is marked with a number that represents the number of threads per inch. These gages provide a standard for thread cutting tools. They have an enclosed angle of 29 degrees and include a 29 degree setting tool. One gage furnishes the correct form for square threads and the other for Acme standard threads.
FILLET AND RADIUS GAGES
The drill point gage consists of a 6-inch hook rule with a 59 degree sliding head that slides up and down the rule. The sliding head can be locked at any position on the rule and is graduated in 1/32 inch. This gage is used to check the accuracy of drill cutting edges after grinding. It is also equipped with a 6-inch hook rule. This tool can be used as a drill point gage, hook rule, plain rule, and a slide caliper for taking outside measurements.
WIRE GAGES
The blades of fillet and radius gages are made of hardrolled steel. The double-ended blades of the gage have a lock which holds the blades in position. The inside and outside radii are on one blade on gage (A). The other gage (B) has separate blades for inside and outside measurements. Each blade of each gage is marked in 64ths. Each gage has 16 blades.
A wire gage is circular in shape with cutouts in the outside edge. Each cutout gages a different size wire, from 0 to 36 of the English Standard Wire Gage. A separate gage is used for American standard wire and another for U.S. Standard sheet and plate iron, and steel. Similar gages are also used to check the size of hot and cold rolled steel, sheet and plate iron, and music wire.
16-4
TM 9-243

DRILL GAGES MARKING GAGES
The twist drill and drill rod gage has a series of holes with size and decimal equivalents stamped adjacent to each hole. One gage measures drill sizes Nos. 1 to 60; the other gage measures drill sizes 1/16 to 1/2 inch in 1/64 inch intervals. Drill gages determine the size of a drill and indicate the correct size of drill to use for given tap size. Drill number and decimal size are also shown in this type gage. Letter size drill gages are also available. Each drill hole is identified by a letter instead of a number, decimal, or fraction.
Marking gages are made of wood or steel. They consist of a graduated beam about 8 inches long on which a head slides. The head can be fastened at any point on the beam with a thumbscrew. The thumbscrew presses a brass shoe tightly against the beam and locks it firmly in position. A steel pin or spur (1) marks the wood and projects from the beam about 1/16 inch. A marking gage is used to mark off guidelines parallel to an edge, end, or surface of a piece of wood. It has a sharp spur or pin which does the marking. A marking gage must be adjusted by setting the head the desired distance from the spur.
USING A THICKNESS GAGE
Thickness (feeler) gages are used in one of two ways: as a means for determining a measure or a means for adjusting to a definite limit. A thickness gage is used to check piston ring gap clearance in a cylinder bore.
A long blade thickness gage is used to determine the fit between large mating surfaces. By combining blades it is possible to obtain a wide variation of thickness.
16-5
TM 9-243
USING A CENTER GAGE

The center gage is used to set thread cutting tools. Four scales on the gage are used for determining the number of threads per inch. The gage is also used to check cut threads and the scales are used to measure threads per inch.
USING A SCREW PITCH GAGE

If the pitch of a thread is not known, it can be determined by comparing it with the standards on the various screw pitch gages. 1. Place a blade of a gage (1) over the threads (2) and check to see whether it meshes; if not, successively check each blade of the gage against the thread until it meshes. The pitch can be read off the correct blade. The blades are made pointed so that they can be inserted in small nuts to check inside threads as well as outside threads.
2.
USING A SMALL HOLE GAGE

The small hole gages perform the same function as telescoping gages, except that they are used in smaller work. 1. 2. 3. Fit the ball-shaped point (1) into the hole or slot (2). Expand the ball-shaped end by turning the screw (3) at the end of the handle. Use micrometer to gage the measurement.
16-6
TM 9-243
USING A TELESCOPING GAGE

1. 2. Loosen the knurled nut (1) at the end of the handle (2). Slightly tilt telescoping gage (3) 5 to 10 degrees and lower into object to be measured. Remove gage by pulling across center line as indicated by arrow. NOTE Take measurement only once. Repeated attempts will produce an inaccurate reading. 5. Measure gage setting with an outside micrometer. (To use an outside micrometer, refer to chapter 7 in this manual.)
3. Tighten knurled nut (1). 4.
USING A THREAD CUTTING TOOL GAGE

1. Place the proper gage (1) over the tool (2). The tool must mesh properly with no light showing between the tool and the gage. Use a 29 degree angle as a guide when grinding cutting tool. After tool fits the angle, the point should be ground off to fit the proper place on the gage for the particular number of threads per inch to be cut.
2. 3.
USING A FILLET AND RADIUS GAGE
1.
A double-ended radius gage blade (1) is used to check the inside corner or fillet (2) of a machined part. Each blade can be locked in position by tightening the clamp.
2.
These gages can be used in any position and at any angle for both inside and outside radii.
16-7
TM 9-243
USING A DRILL POINT GAGE

The method for sharpening the cutting edges of a drill is to do one lip at a time. Each lip must have the same length and have the same angle in relation to the axis of the drill. Set the sliding head securely on the rule at the mark equal to the length of the drill. Place the drill vertically against the rule so that the drill lip contacts the 59 degree angle of the sliding head. Hold up to light; correct angle is obtained when no light is seen between gage and drill.
USING A WIRE GAGE

Determine the size of both sheet stock and wire by using a correct sheet and plate or wire gage.
USING A DRILL GAGE

The drill gage is used to determine the size of a drill. The drill size, number and decimal size or letter size are stamped on the gage beside each hole. A chart on the gage indicates the correct size of drill to use for a given tap size.
16-8
TM 9-243
USING MARKING GAGES

Press the head (1) firmly against the edge of the work (2) to be marked. With a wrist motion, tip the gage forward until the spur touches the work. Push the gage along the edge to mark the work, keeping the head firmly against the work.
CARE OF GAGES
1. Exercise care when using thickness gages to measure clearance of knives and cutters on machines. Do not lower knife on thickness blade and then try to remove the gage. The blade may be shaved off if it is too tight. Never use gages for cleaning slots or holes. When blades are damaged or worn they should be replaced. Blades. in a case are removed by loosening the clamp and sliding out the damaged blade. Insert new blade and tighten clamp. 2. Always coat metal parts of all gages with a light film of oil when not in use to prevent rust. Store gages in separate containers. Do not pile gages on each other. Always return blades of leaf-type gages to case after use. Keep graduations and markings on all gages clean and legible. Do not drop any gage. Small scratches or nicks will result in inaccurate measurements.
16-9/(16-10 blank)
TM 9-243
Chapter 17 PLIERS AND TONGS

The Types and Uses section provides you with a list of some types of pliers and tongs. These pages should help you select the right pair to do the job. The Using section tells you how to use the pliers or tongs to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . Slip-joint pliers . . . . . . . . . . . . . . . . . . . . . . Diagonal cutting pliers . . . . . . . . . . . . . . . Linemans side cutting pliers . . . . . . . . . . Parallel jaw pliers . . . . . . . . . . . . . . . . . . . . Flat-nose pliers . . . . . . . . . . . . . . . . . . . . . . Round-nose pliers . . . . . . . . . . . . . . . . . . . Straight-lip flat-jaw tongs . . . . . . . . . . . . . End cutting pliers . . . . . . . . . . . . . . . . . . . . Wire strippers . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17-2 17-2 17-2 17-2 17-2 17-2 17-2 17-3 17-3 17-3 17-3 17-5
17-1
TM 9-243
TYPES AND USES

SLIP-JOINT PLIERS
point, where maximum pressure may be applied. They are ground at an angle permitting sharp flush cuts on electrical wire. A pair of croppers is located above the pivot. They are used to shear larger wire. Linemans pliers used around electrical circuits have insulated sleeves over the handles to reduce the possibility of electrical shock.
PARALLEL JAW PLIERS

The slip-joint combination pliers have serrated (grooved) jaws, with a rod-gripping section, a cutting edge, and a pivot. The serrated jaws and rod-gripping section are used to hold objects. The cutting edge permits the cutting of soft wire and nails. However, cutting hard materials or large gage wire will spring the jaws, making the pliers useless. The pivot is used to adjust the jaw opening to handle large or small objects.
DIAGONAL CUTTING PLIERS
The parallel jaw pliers are constructed so that the jaws remain parallel to each other throughout the entire distance of travel. It has two jaws, a pivot pin, curved handles, and tension springs. The tension springs are contained within the curved handles and will open the jaws when the handles are released. These pliers are used to grip objects which have flat surfaces.
FLAT-NOSE PLIERS
The diagonal cutting pliers have a fixed pivot. The jaws are offset by about 15 degrees and are shaped to give enough knuckle clearance while making flush cuts. The diagonal cutting pliers are used for cutting small, light materials such as wire, cotter pins, and similar materials. These pliers are not to be used to hold or grip objects.
LINEMANS SIDE CUTTING PLIERS
The flat-nose pliers have flat serrated jaws, a fixed pivot, and curved handles which may have insulated sleeves. These pliers are used to bend light sheet metal and wire.
ROUND-NOSE PLIERS
The linemans side cutting pliers have serrated jaws, a rod-gripping section, side cutters, wire cropper, a fixed pivot, and parallel handles. The flat serrated jaws are used to bend sheet metal and twist electrical wire. The rod-gripping section is used to hold rods and bend small rods. The side cutters are located just above the pivot
The round-nose pliers are used to make loops in soft wire. It has smooth, round jaws, a fixed pivot, and curved handles, which may have insulated sleeves.
17-2
TM 9-243

STRAIGHT-LIP FLAT-JAW TONGS WIRE STRIPPERS (MULTIPURPOSE)
The straight-lip flat-jaw tongs have two straight jaws, a fixed pivot point, and long, straight handles. These tongs are used to hold bearings and bearing inserts while setting them in place.
END CUTTING PLIERS
Wire strippers are used to strip insulation from electrical cord. When closed around wire, only the insulation is cut. The wire core remains undamaged.
The end cutting pliers are used to crop wire flush to the working surface. They are designed to keep hands and fingers safely away from the wire ends.
USING SLIP-JOINT PLIERS
NOTE The following procedure for bending the ends of a cotter pin after installation is not the only use of slip-joint pliers.
With cotter pin installed, push rounded head of pin (1) with thumb of one hand. Grasp the long section of extending cotter pin (2) with pliers, and bend it back flat against the metal surface or nut.
Grasp the other section of the extending cotter pin (3) and bend it back flat against the metal surface or nut.
17-3
TM 9-243
USING SLIP-JOINT PLIERS - Continued
Adjust pliers (4) to obtain a wide jaw opening.
CAUTION Too much pressure could break the cotter pin or spring the plier jaws.
Place plier jaws (5) around both bent ends of the cotter pin and apply pressure on the handles, bending cotter pin ends flush.
USING DIAGONAL CUTTING PLIERS

WARNING WEAR EYE PROTECTION. KEEP FINGERS AWAY FROM JAWS AND CUTTING EDGES.
CAUTION Diagonal cutting pliers are to be used only for cutting.
NOTE The following procedure for the removal of a cotter pin is not the only use of diagonal cutting pliers.
1 2
Position cutters so the rounded end (1) of the cotter pin is between the cutting jaws. Close the cutting jaws by applying pressure to the handles (2). This will shear off the end of the cotter pin (3).
17-4
TM 9-243
USING LINEMANS SIDE CUTTING PLIERS

NOTE The following procedure for twisting wires is not the only use of linemans side cutting pliers.
2 3
Grasp the ends of the wires (2) firmly on the serrated jaws (3) and twist the pliers (4). Continue twisting pliers until wire has been twisted to desired length.
Using one hand, hold wires to be twisted (1) just above the point where the twist is to begin.
Open plier jaws and place the ends of the twisted wires between the cutting edges (5). Trim the ends of the wire.
CARE OF PLIERS AND TONGS

Remove dirt and grease with a clean rag and apply a light coat of oil after each use. Store pliers in a tool box or hang on racks when not in use. Do not remove insulation on handles or oil handles which are insulated. Do not use pliers for prying or for removing nuts or bolts. Replace all pliers which have broken jaws, handles, or cutting edges.
17-5/(17-6 blank)
TM 9-243
Chapter 18 VISES
The Types and Uses section provides you with a list of some of the types of vises. These pages should help you select the right vise to do the job.
The Using section tells you how to use the vise to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . Machinists bench vise . . . . . . . . . . . . . . . Bench and pipe vise . . . . . . . . . . . . . . . . . Clamp base bench vise . . . . . . . . . . . . . . Pipe vise . . . . . . . . . . . . . . . . . . . . . . . . . . . Machine table vise . . . . . . . . . . . . . . . . . . . Pin vise . . . . . . . . . . . . . . . . . . . . . . . . . . . . Piston holding vise . . . . . . . . . . . . . . . . . . Handsaw filing vise . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18-2 18-2 18-2 18-2 18-2 18-3 18-3 18-3 18-3 18-4 18-5
18-1
TM 9-243
TYPES AND USES

MACHINIST'S BENCH VISE CLAMP BASE BENCH VISE
The machinists bench vise has rough jaws which prevent the work from slipping. It has a swivel base, allowing the user to position the vise in a better working position. Machinists bench vises are usually bolted to a work bench or table. They are used for holding or clamping large, heavy objects.
The clamp base bench vise is a lightweight, portable machinists vise. It is attached to a table or bench with the mounting clamp. It has rough jaws for holding material and may have a swivel base. Clamp base bench vises are used to hold light materials or in areas where a heavier vise is not available.
BENCH AND PIPE VISE
PIPE VISE
The bench and pipe vise is a dual purpose vise. It has rough jaws and a swivel base similar to the machinists bench vise. However, it also has built-in pipe jaws. Bench and pipe vises are usually bolted to a work bench or table. They are used for holding or clamping heavy objects, holding pipe for cutting and threading, and for forming and shaping metal.
The pipe vise is a special purpose vise designed to hold round stock. It has hinged jaws which allow the user to position the work and then lock it in place. Some pipe vises have a section of chain instead of jaws for holding the pipe. Pipe vises are usually bench mounted. They are used to hold pipe from 1/8 inch to 8 inches in diameter while cutting or threading.
18-2
TM 9-243

MACHINE TABLE VISE PISTON HOLDING VISE
The machine table vise is a special purpose vise which may be bolted to a drill press, lathe, or table. It is available in two sizes, one having a 3-1/2-inch jaw width and a 3-inch jaw opening, and the other having a 6-inch jaw width and a 6-inch jaw opening. Machine table vises are used to hold small pieces of wood or metal for machining or drilling operations.
The piston holding vise is a special purpose vise which can hold engine pistons up to and including 5-1/2 inches in diameter. This vise may be bolted to a bench or table.
PIN VISE
HANDSAW FILING VISE
The pin vise is a special purpose vise which has a knurled metal handle and a chuck. It is designed to hold material from 0 to 0.187 inches in diameter. The pin vise is used to hold files, taps, and small drills during machining operations.
The handsaw filing vise is a special purpose vise used for holding handsaws while they are being sharpened. It has jaws between 9-1/2 and 11 inches wide, and an attachment for holding a file at a constant angle.
18-3
TM 9-243
USING A MACHINIST'S BENCH VISE

WARNING MAKE-SURE THE VISE IS BOLTED SECURELY TO A BENCH OR TABLE AND THE SWIVEL BASE IS LOCKED.
Open jaws (1) of vise wide enough to allow you to insert the object you want to clamp. CAUTION Use brass or copper caps on vise jaws to protect soft material when clamping. CAUTION Do not strike vise with a heavy object or try to hold large work in a small vise.
2 3
Insert object (2) to be clamped between vise jaws and tighten handle (3). Work should be held firmly in place, but the jaws should not be so tight that they mar the finish. A piece of rawhide or leather may be used to protect highly polished surfaces: NOTE When holding hard material in vise jaws tightened by hand, give the vise handle a sharp rap for final tightening.
18-4
TM 9-243
USING A PIPE VISE

WARNING PIPE ENDS ARE EXTREMELY SHARP. HANDLE WITH CARE. NOTE The following procedure provides the steps required to fasten a piece of pipe in a hinged jaw pipe vise.
3 4
Insert section of pipe (4) in vise and close pipe vise, by pushing locking device against lip on the side of the lower holding jaw (5). Insert locking bolt through aligned holes of upper and lower lip jaws.
Open the pipe-holding jaws (1) by turning the threaded T-handle (2)
CAUTION Do not apply too much pressure to copper or aluminum pipe.
Tighten the pipe holding jaws by turning the threaded T-handle.
Lift locking device (3) and open pipe vise.
CARE OF VISES
Clean with a rag after each use, and apply a light coat of oil. Never strike avise with a heavy object or try to hold large work in a small vise. Keep jaws in good condition. Never oil the swivel base or swivel joint, as this decreases its holding power. When not using a vise, bring the jaws lightly together and leave the handle in a vertical position. This will protect the jaws.
18-5/(18-6 blank)
TM 9-243
Chapter 19 CLAMPS
The Types and Uses section provides you with a list of some of the types of clamps. These pages should help you select the right clamp to do the job. The Using section tells you how to use the clamps to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . C-clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand screw clamps . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19-2 19-2 19-2 19-2 19-3
19-1
TM 9-243
TYPES AND USES

C-CLAMPS HAND SCREW CLAMPS
C-clamps are used to hold work which cannot be held in a vise, or which has to be held for extended periods of time. They are available in a variety of sizes.
The hand screw clamp is made up of two hardwood or high impact plastic jaws (1) and two hand-operated screws (2) which hold the clamp together. The hand screw clamp is used for holding wood while gluing. They are available in a variety of sizes.
USING A C-CLAMP
Select a clamp which has an opening about 1-1/2 to 2 inches wider than the material to be clamped. Glass and highly polished surfaces must be protected. Use brass shims or wooden blocks. Open clamp as wide as it will go.
Align work and protective blocks if required. Place clamp (1) in position, and tighten operating screw (2) until contact is made with material being clamped. Check alignment of material being clamped. Check that the clamp is applying even pressure over entire surface. CAUTION Do not use wrenches or bars to tighten clamps.
Tighten clamp against surface.
19-2
TM 9-243
USING A HAND SCREW CLAMP

CAUTION Use only on wood. Examine material to be clamped and select a clamp which will span across the work.
Tighten operating screws (2) making sure the clamp jaws remain parallel. Be sure jaws fit firmly on work. Properly clamped work will form a square.
1 Open the clamp jaws (1) and place the work

between the jaws. Keep jaws parallel. Use rawhide or soft leather to protect highly polished surface.
CAUTION Make sure vise jaws remain parallel to edges of work.
CARE OF C-CLAMPS
Clean threads and swivel with a rag, and lubricate with a light coat of oil. Store on a rack, on pins, or in a tool box. For long storage periods, apply a rust-preventive compound.
CARE OF HAND SCREW CLAMPS

Lubricate screws with a few drops of light oil. Apply light coat of linseed oil to wood surfaces. Store clamps on racks, pins, or carefully place them in your tool box. Wipe clamps off with a rag before storing.
19-3/(19-4 blank)
TM 9-243
Chapter 20 JACKS
The Types and Uses section provides you with a list of some of the types of jacks. These pages should help you select the right jack to do the job. The Using section tells you how to use the jack to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . Screw jacks . . . . . . . . . . . . . . . . . . . . . . . . . Ratchet lever jacks . . . . . . . . . . . . . . . . . Hydraulic jacks . . . . . . . . . . . . . . . . . . . . . SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20-2 20-2 20-3 20-3 20-4 20-5 20-7
20-1
TM 9-243
TYPES AND USES

Jacks are used to raise or lower work and heavy loads short distances. Some jacks are used for pushing and pulling operations. Others are used for spreading and clamping operations.
SCREW JACKS
Vertical screw jacks come in several capacities and different lowered and raised heights. The screw moves up or down, depending on the direction the handle is turned. These jacks are used for many different purposes. They can be used to lift vehicles. They can also be used to raise heavy crates, small buildings, or other items too heavy to be raised by prying with wrecking bars.
The vertical screw jack with collapsible handle is operated by hand using the collapsible handle which is inserted in a socket.
The vertical bell base screw jack is operated by hand using a steel bar handle which is inserted in the holes of the top housing or head.
Another type of screw jack is called an outrigger jack. It is equipped with end fittings which permit pulling parts together or pushing them apart.
20-2
TM 9-243

RATCHET LEVER JACKS
A vertical ratchet lever jack has a rack bar that is raised or lowered through a ratchet lever. Some are equipped with a double socket, one for lowering, one for raising. Others have one socket and have an automatic lowering feature. An outrigger ratchet jack is ratchet operated and has an extra reverse ratchet handle and a base plate.
A push-pull hydraulic jack consists of a pump (1) and ram (2) connected by a hydraulic or oil hose (3). These jacks are rated at 3, 7, 20, 30, and 100-ton capacities and have many different applications. The push-pull hydraulic jacks are furnished with an assortment of attachments that enable you to perform countless pushing, pulling, lifting, pressing, bending, spreading, and clamping operations. The pump is hand operated. Simply turn the control valve (4) on the side of the pump clockwise, stroke the hand lever (5) up and down and the ram will extend. The flexible hydraulic or oil hose allows you to operate the ram from a safe distance in any desired position. The ram retracts automatically by turning the control valve counterclockwise. The attachments can be threaded to the end of the plunger, to the ram body, or into the ram base.
HYDRAULIC JACKS
A hydraulic jack operates through pressure applied to one side of a hydraulic cylinder which moves the jack head. These jacks are automatically lowered by releasing the pressure. Vertical hydraulic jacks come in a variety of types, in capacities from 3 to 100 tons, having different extended heights.
20-3
TM 9-243

Illustrated below are some standard combinations of the push-pull hydraulic jack attachments for various operations. 1. Jack pushing combinations 2. Jack pulling combinations 3. Jack spreading combinations 4. Jack clamping combinations
SAFETY
1. Keep fingers away from all moving parts. WARNING NEVER GET UNDER A LOAD THAT IS ONLY SUPPORTED BY A JACK. ANY JACK IS SUBJECT TO FAILURE AND PERSONAL INJURY COULD RESULT. 2. When jacking up vehicles, make certain no one is under the vehicle to be raised. Set the hand brake firmly and block the front wheels if a rear wheel is being changed. Block the rear wheels if a front wheel is being changed. Place blocking or other
3. 4. 5.
supports under the vehicle when it is raised to the desired height to prevent it from dropping if the jack fails. Make certain that hydraulic jacks are filled with oil and that there are no visible oil leaks before using. Any new or repaired jack should be carefully inspected by the operator prior to use. Overloading can be hazardous to the jack, the operating personnel, and the load in event of jack failure. Be aware of the capabilities of the jack, especially its load capacity.
6.
20-4
TM 9-243
USING A BELL BASE SCREW JACK
3
Insert the handle or bar (1) in the hole in the top housing or head (2).
The jack will raise the load (3) with every degree turned on the handle.
4 2
Turn or push the handle to the right to raise the jack, to the left to lower the jack.
Block the load to withdraw the jack.
Screw the jack all the way down in the lower housing and withdraw the handle or bar for storage upon completion of the job.
20-5
TM 9-243
USING A RATCHET LEVER JACK
1 The operator should familiarize himself with the

jack, its capabilities and its operations. The reversing lever (1) is located below the lifting mechanism cover (2) on the left side of jack when viewed from the lifting lever. When preparing to lift a load, the head (3) can be pulled up by hand to meet the load.
To lower a load, push reversing lever to straightdown position and operate the lever. The jack will lower the load one notch for each upstroke of the lever.
2 To raise a load, pull reversing lever up and toward

the operator and operate the lever (4). The jack will raise the load one notch for each lever downstroke. The rack (5) cannot be ratcheted out of the base, as it is designed to stop when raised to its top limit.
4 When the head of the five-ton jack is not supporting

a load, the rack can be allowed to fall free by pressing the reversing lever all the way to the rear and slightly lifting up on the lifting lever. The rack will not fall free if even a slight load is still on the head.
20-6
TM 9-243
CARE OF JACKS
1. 2. Coat all surfaces with a thin film of light oil when not in use. For long periods of storage, the jacks should be covered with a rust-preventive compound and stored in a dry place. Periodically check hydraulic fluid level in push-pull hydraulic jacks. Stand the pump on end before taking out the fill plug, then fill with oil. Make sure the ram is in the retracted position when checking level of oil and when filling. 4. Ratchet lever jacks should be well greased. 4 thin coat applied with hand or brush is sufficient for all movable parts except the bushings. The bushings should be filled with grease in the small hole-provided for greasing purposes. Keep rack sides and front greased, but do not grease the rack teeth.
3.
20-7/(20-8 blank)
TM 9-243
Chapter 21 HAMMERS, MALLETS AND MAULS

The Types and Uses pages provide you with a list of the more common types of hammers. These pages should help you select the right hammer for the job. The Care and Safety pages tell you how to keep your tools in proper condition and how to use them safely. The Using Hammers pages tell you how to perform a specific task using the carpenters, machinists, and soft-faced hammers. INDEX TYPES AND USES
Item Page
There are many more uses for these hammers, however. By becoming familiar with the uses outlined, you will build a good background for using any hammer. The Repair pages tell you how to replace a wooden handle.
TYPES AND USES . . . . . . . . . . . . . . . . . Carpenters hammer . . . . . . . . . . . . . . . . Machinists peen hammers . . . . . . . . . . . Bumping body hammer . . . . . . . . . . . . . Blacksmiths or sledge hammers . . . . . . Jewelers hammer . . . . . . . . . . . . . . . . . . Masons hammer . . . . . . . . . . . . . . . . . . . . Napping hammer . . . . . . . . . . . . . . . . . . . Riveting hammer . . . . . . . . . . . . . . . . . . . Sawmakers hammer . . . . . . . . . . . . . . . . Setting hammer . . . . . . . . . . . . . . . . . . . . Soft-faced hammer . . . . . . . . . . . . . . . . . Lead or copper hammer . . . . . . . . . . . . . Inserted soft-faced hammer . . . . . . . . . . Trimmers hammer . . . . . . . . . . . . . . . . . Welders hammer . . . . . . . . . . . . . . . . . . . Dead blow hammers . . . . . . . . . . . . . . . . . MALLETS . . . . . . . . . . . . . . . . . . . . . . . . . . Carpenters mallet . . . . . . . . . . . . . . . . . . . Rawhide mallet . . . . . . . . . . . . . . . . . . . . . . Rubber mallet . . . . . . . . . . . . . . . . . . . . . . . Tinners mallet . . . . . . . . . . . . . . . . . . . . . . MAULS . . . . . . . . . . . . . . . . . . . . . . . . . . Railroad track maul . . . . . . . . . . . . . . . . . . Wooden maul . . . . . . . . . . . . . . . . . . . . . . . SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REPLACING THE HANDLE . . . . . . . . .
21-2 21-2 21-2 21-3 21-3 21-4 21-4 21-4 21-4 21-4 21-5 21-5 21-5 21-5 21-6 21-6 21-7 21-7 21-7 21-7 21-7 21-7 21-8 21-8 21-8 21-8 21-9 21-12 21-13
21-1
TM 9-243
TYPES AND USES

Parts of a hammer 1 Claw 2 Eye 3 Handle are as follows: 4 Neck 5 Striking face 6 Cheek And there are two types of striking faces.
FLAT FACE
BELL FACE
NOTE When using a flat-faced hammer to drive a nail, the nail head must be square with the face of the hammer at time of impact. The bell-faced hammer offers a uniform face to the nail head even though the hammer face is slightly tipped at time of impact. Hammers come in 7, 13, 16 and 20 ounce sizes. Your selection should be based upon the following: flat face for rough work, or bell face for finishing work where you dont want dents in the finish. The straight claw is generally used for ripping and framing. The curved claw is preferred for general use.
CARPENTERS HAMMER
MACHINISTS PEEN HAMMER

The carpenters hammer is used for driving and pulling nails and tapping wood chisels. There are two types of claws, All machinists peen hammers have a flat striking face on one end of the head for striking punches and chisels. The other end of the head can be one of the following:
CURVED CLAW
STRAIGHT CLAW
CAUTION Never use a claw hammer on a steel punch or on hardened steel-cut or masonry nails. The face is too soft and could chip. Be sure to check for a loose head or a cracked handle before use.
A ball peen hammer is used for forming soft metal, peening rivet heads, and striking metal in out-of-the-way places.
21-2
TM 9-243

BLACKSMITHS OR SLEDGE HAMMERS
Blacksmiths or sledge hammers are used for striking punches and chisels, for breaking stones and concrete, and for setting timbers. These hammers, although similar to the machinists hammers, give the user the advantage of a heavier head and a longer handle.
A cross peen hammer is used as a chisel for removing rivet heads and for stretching or bending metal.
A double face sledge hammer has similar faces on both sides of the head.
A straight peen hammer is used like the cross peen but differs from the cross peen since its peening edge is turned ninety degrees. This keeps the handle parallel to the struck surface.
BUMPING BODY HAMMER
The club hammer is a heavy double-faced demolition hammer. It is primarily used to break up masonry.
A bumping body hammer is used to straighten and form metal.
Cross peen hammers have a broad flat face on one side of the head and a peening chisel edge on the other side.
21-3
TM 9-243

BLACKSMITHS OR SLEDGE HAMMERS (Cont) NAPPING HAMMER
The straight peen is similar to the cross peen except that its peening edge is turned ninety degrees. This keeps the handle parallel to the struck surface.
JEWELERS HAMMER
The napping hammer has a high carbon steel head with two tapered faces and weighs about 3 pounds. It is used for chipping stone surfaces or for forming stones during road construction or similar stone work.
RIVETING HAMMER
The jewelers hammer has a lightweight head weighing between 1-3/4 and 2 ounces. It is used to drive pins and shafts from precision instruments.
The riveting hammer has a round face on one end of the head. It is used for peening rivet heads. The other end has a tapered chisel which is used for upsetting rivets.
MASONS HAMMER
SAWMAKERS HAMMER
The masons hammer has a flat striking face on one end of the head and a tapered chisel on the other end. It is used for setting and cutting bricks and flat stones.
The sawmakers hammer has a tapered blunt face on one end of the head and a tapered chisel face on the other end. It is used for setting the teeth on saws when a setting tool is unavailable.
21-4
TM 9-243

SETTING HAMMER LEAD OR COPPER HAMMER
The setting hammer has a square flat face on one end of the head and a sloping beveled edge on the other end. It is used in sheet metal work for leveling and bending edges and for setting double seams.
SOFT-FACED HAMMER
Lead or copper hammers are usually used for aligning steel surfaces. Copper hammers range in head weight from 8 ounces up to 3 pounds. Working surfaces of lead and copper hammers may be filed to restore even faces. Molds are available for repouring lead hammers.
INSERTED SOFT-FACED HAMMER
Soft-faced hammers are capable of delivering heavy blows to machined, highly polished or soft surfaces without damaging the surface.
Inserted soft-faced hammers provide the user with a dual purpose hammer. Any two faces may be assembled on a single handle holder. The following tables will assist you in selecting the proper face hardness for the task you are attempting: Hardness soft Medium Tough Medium Hard Extra Hard Symbol S M T N H XH Color Brown Red Green Cream Black Yellow
Hard
Faces and handle holders are available in 1 inch, 1-1/2 inch, 2 inch, 2-1/2 inch and 3 inch diameters.
21-5
TM 9-243

INSERTED SOFT-FACED HAMMER (Cont)
USE THIS CONVERSION CHART FOR FACE SELECTION

Medium Hard Extra Hard
Type
Soft
Medium
Tough
Hard
Soft Rubber Wood Rubber Hard Wood Lead Plastic Rawhide Micarta Fibre Copper
S S
M M T T T T
N N H H H H XH XH XH XH
TRIMMERS HAMMER
WELDERS HAMMER
The trimmers hammer has a round flat face on one end of the head and has a tapered chisel face on the other end. A claw is attached on the end of the handle and is used for pulling tacks. It is used for installing tacks and brads.
The welders hammer has one or two tapered chisel faces. Those having only one tapered face have a replaceable brush attached. The hammer face is used for chipping welds, while the brush is used for cleaning welds and brushing away the slag chipped from the weld.
21-6
TM 9-243

DEAD BLOW HAMMERS
MALLETS
CARPENTERS MALLET
The carpenters mallet has a cylindrical wooden head often bound with thin metal bands for support. It is used for driving dowels, small stakes, wooden handled chisels and for forming and shaping sheet metal.
RAWHIDE MALLET
The rawhide mallet has a cylindrical head which is made by tightly wrapping and staking a sheet of leather. It is used for forming and shaping sheet metal.
RUBBER MALLET
The rubber mallet has a cylindrical rubber head. It is used for forming sheet metal, driving dowels, and small stakes. The dead blow hammer is a shot-filled, rubber encased, single-piece hammer. It features a wrap-around grip and a flanged butt. Four basic types of dead blow hammers are currently in use. They are: the standard head, slimline head, sledge, and ball peen. Some advantages of the dead blow hammers are greater striking power, and the elimination of broken heads and splintered handles.
TINNERS MALLET
The tinners mallet has a cylindrical wooden head which is from 1-1/4 to 3-1/2 inches in diameter and from 3 to 6 inches in length. It is used to form and shape sheet metal.
21-7
TM 9-243
TYPES AND USES - Continued MAULS

RAILROAD TRACK MAUL WOODEN MAUL
The railroad track maul has a flat faced tapered head which weighs about 10 pounds. They are used for driving railroad track spikes.
The wooden maul has a cylindrical head which is about 8 inches in diameter and about 10 inches long. It is used to drive wooden pickets, posts and stakes.
SAFETY
WARNING NEVER, NEVER USE AN UNSAFE HAMMER. BEFORE USING, CHECK FOR A LOOSE HEAD OR A CRACKED HANDLE. DO NOT USE HANDLE AS A PRY BAR, OR TO KNOCK SHARP EDGES TOGETHER. 1. 2. Inspect the faces of steel hammers for wear, dents, or chips. They can be dangerous if chips fly off. Replace the hammer if these conditions are found.
4.
File edges of copper, lead or plastic mallets down to the original shape.
3.
Inspect copper, lead, plastic, or rawhide mallets for mushrooming.
5.
Trim a rawhide mallet with a knife.
21-8
TM 9-243
SAFETY - Continued
Specific Steps to Take 1. Make sure handle (1) is tight in head (2). Do not tape a cracked handle. REPLACE IT. 2. Make sure wedges (3) are in handle (1), keeping head (2) tight on handle. USE ONLY CORRECT WEDGES. 3. Make sure striking face (4) and ball peen (5) are free of oil.
USING HAMMERS
The proper way to hold any hammer is near the end of the handle. The handle is shaped for gripping without slipping from your grasp at this position, and gives the best control and impact with least effort. Strike nail or tool squarely and on center to prevent the hammer from glancing off.
The wrist and arm motion depends on the power of the impact required. Small nails require light blows almost entirely from a wrist motion. Heavy blows, needed, to drive a large nail or other similar task, come from the wrist, forearm and shouIder.
21-9
TM 9-243
USING A CARPENTERS HAMMER
WARNING WEAR EYE PROTECTION AND WATCH THE FINGERS. CAUTION Never use a claw hammer on a steel punch or on hardened steel-cut or masonry nails. The face is too soft and could chip. Be sure to check for a loose head or a cracked handle before use. The following set-up is established to provide practice driving nails successfully. NOTE A piece of paper or a comb (2) can be used to hold small nails.
3 1
Lay two pieces of wood parallel to each other. Place a third piece on top and align so that the edges are even.
Tap nail head (3) with hammer face (4) until the nail will remain standing by itself.
4
Support a common nail (1) between thumb and first finger about halfway up the nail.
Remove fingers and drive nail flush. Make sure the hand supporting the work is not in direct line with the hammer blows.
21-10
TM 9-243
USING A CARPENTERS HAMMER - Continued
The claw end (1) of the hammer is for pulling nails or prying boards. Slip the claw under the nail head (2) as far as it will go, to prevent bending the head up.
Pull the handle (3) to a vertical position to withdraw the nail. For longer nails, place a block of wood (4) under the head for better leverage.
USING AN INSERTED FACE HAMMER
Unwrap bearing (3) and center over shaft (4).
NOTE The following procedure is only one of many uses of a soft-faced hammer.
Make sure faces (1) are tight in holder (2).
While supporting bearing with left hand use softfaced hammer to tap in a circular motion until edge of bearing is flush with shaft (4).
21-11
TM 9-243
USING A MACHINISTS BALL PEEN HAMMER
The following procedure is one of many uses of the machinists hammer.
3 Catch the pin in your right hand before it falls out of

the shaft. NOTE After the pin is about half way out of the shaft, you should not hold the punch.
To remove a spring pin from a shaft, select a drift punch about the same diameter as the pin and a machinists hammer having a face larger than the punch head. Hold punch (1) in your left hand centered over pin (2), tap punch lightly with hammer (3). This should move the pin. NOTE It may be necessary to apply penetrating oil to the pin before it will move.
CARE OF HAMMERS
1. Check for cracks in handle (1). Replace handle if cracked. Check for loose head (2). Replace missing or makeshift wedges to be sure head is tight. If not tight, replace handle. Periodically rub a small amount of linseed oil into the wood handles (1) to prevent the wood from drying out and shrinking. Replace hammer if it has a worn or chipped face (3) or claw (4). Lightly lubricate metal parts when storing the hammer for a lengthy period. Wipe oil and grease from rubber mallets to prevent damage to rubber.
2.
3. 4. 5.
21-12
TM 9-243
CARE OF INSERTED FACE HAMMERS
1.
Broken or chipped faces may be removed by turning in a counterclockwise direction. NOTE Use a pair of pliers or a rag on broken faces to prevent scraping your hands.
2. 3. 4.
Wipe out face seat on holder with a clean rag. Install new face by turning in a clockwise direction. If holder is broken or cracked, remove both faces by turning in a counterclockwise direction. Obtain a new holder and install faces by turning in a clockwise direction.
REPLACING THE HANDLE

MATERIALS ASSORTED WEDGES TOOLS
WOODEN WEDGE
NEW HANDLE
METAL WEDGE
HAMMER
RUBBER MALLET
WOOD RASP
HAND SAW
BENCH GRINDER
VISE
The above items are the basic materials required to replace the handle on a typical carpenters hammer.
21-13
TM 9-243
REPLACING THE HANDLE - Continued

REMOVING OLD HAMMER HANDLE 1 2
If the handle is split or broken, remove it from the head. If the handle is too tight to pull loose from the head, proceed as follows: Place hammer in vise. Saw off handle (1) close to head (2). Drive the remaining handle out through the large end of the head (3) using drift pin. Save the wedges.
INSTALLATION OF NEW HANDLE
WARNING WEAR EYE PROTECTION AND WATCH THE FINGERS.
Insert handle (1) in head (2).
NEW HANDLE
WOODEN WEDGE
METAL WEDGE
Obtain new handle and wedges.
Seat handle in head with a rubber mallet (3).
21-14
TM 9-243
REPLACING THE HANDLE - Continued
Drive wooden wedge (4) in handle face (5) with hammer (6).
7 Select metal wedge (12) and drive into wooden

wedge with hammer (6):
5 Place hammer (7) in vise (8). Using handsaw (9)

remove projecting end of wedge (10).
8 Remove excess portion of wedge using a bench

grinder (13). Check handle. If its tight, the task is complete. If handle is loose, repeat procedure.
6 Remove excess portion of wedge using wood

rasp (11).
21-15/(21-16 blank)
TM 9-243
Chapter 22 SCREWDRIVERS
The Types and Uses section provides you with a list of some of the types of screwdrivers. These pages should help you select the right screwdriver to do the job.
The Using section tells you how to use the screwdriver to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . 22-2 Common screwdrivers . . . . . . . . . . . . . . 22-2 Cross-tip screwdrivers . . . . . . . . . . . . . . 22-3 Cross-point screwdrivers . . . . . . . . . . . . . 22-3 Clutch head screwdrivers . . . . . . . . . . . . 22-3 Off set screwdrivers . . . . . . . . . . . . . . . . . 22-3 Ratchet screwdrivers . . . . . . . . . . . . . . . . 22-4 Screwdriver bits . . . . . . . . . . . . . . . . . . . . 22-4 Jewelers screwdrivers . . . . . . . . . . . . . . 22-4 Flexible screwdrivers . . . . . . . . . . . . . . . . . 22-4 Radio and pocket screwdrivers . . . . . . . 22-5 Screw starter or gimlet . . . . . . . . . . . . . . . 22-5 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-5 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-5 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-8
22-1
TM 9-243
TYPES AND USES
Screwdrivers are available in many different shapes, sizes, and materials. Screwdrivers are used for driving or removing screws or bolts with slotted, recessed, or special heads.
COMMON SCREWDRIVERS
Some common screwdrivers have a screw-holding feature. These are used for working in close quarters, overhead, and hard to reach places. The two most common types are the clip (1) and sliding collar (2). After the screw has been firmly started, switch to a conventional screwdriver to complete the job. NOTE Do not use sliding-cover, split-type screwdrivers for final tightening of screws.
Close quarter or stubby common screwdrivers are used for working in close quarters where conventional screwdrivers will not fit. The common screwdriver has a round steel blade with a wood or plastic handle, usually fluted for a good grip. Integral blade screwdrivers are used for heavy-duty work.
Common cabinet screwdrivers have a thin, round blade and are used to reach and drive or remove screws in deep, counterbored holes.
Other common heavy-duty screwdrivers have square blades so a wrench can be used to turn them.
22-2
TM 9-243

CROSS-TIP SCREWDRIVERS
CLUTCH HEAD SCREWDRIVERS
The tip of a cross-tip screwdriver is shaped like a cross so that it fits into cross-tip screws. Cross-tip screws have two slots which cross at the center. These screwdrivers are made with four different sized tips. Cross-tip screwdrivers also have different length blades ranging from 1 inch to 8 inches.
Clutch head screwdrivers are used to drive clutchbit screws. These screws have recessed heads and are commonly called butterfly or figure-eight screws. There are two styles of clutch heads, old style and new style.
OFFSET SCREWDRIVERS
CROSS-POINT SCREWDRIVERS
Cross-point screwdrivers are similar to the cross-tip. The cross-point slots meet at an exact right angle at their intersection. These screwdrivers are issued in 3 to 8-inch sizes.
Offset screwdrivers are used to drive or remove screws that cannot be lined up straight with common screwdrivers, or are located in tight corners. Some offset screwdrivers are made with two blades, one of a different size at each end. Others are ratchet-type offset, which are reversible for working in tight spots and allow the screw to be driven without having to remove the tip from the screw head. A double-tip offset screwdriver has four blades.
22-3
TM 9-243

RATCHET SCREWDRIVERS JEWELERS SCREWDRIVERS
Ratchet screwdrivers are used to drive or remove small screws rapidly. The spiral ratchet screwdriver automatically drives or removes screws. It can be adjusted to turn left, right, or locked to act as a common screwdriver. Some spiral ratchets have a spring in the handle which automatically returns the handle for the next stroke. Another style of ratchet screwdriver has a knurled collar for rotating the blade with your fingers. The spiral type has separate blades (1) that are inserted in the chuck (2). The common ratchet screwdriver has one integral blade (3).
Jewelers screwdrivers are made for driving and removing small size screws. They usually have knurled handles (1), and a swivel end finger rest plate (2). The tips (3) range from 0.025 inch to 0.1406 inch wide. Some jewelers screwdrivers have removable blades.
FLEXIBLE SCREWDRIVERS
SCREWDRIVER BITS
A flexible screwdriver has a spring steel blade which bends, allowing the user to get around flanges, shoulders, and other parts to drive and remove screws.
A screwdriver bit is a screwdriver blade with a square, hex, or notched shank so that it can be used with other tools: Breast drill Ratchet bit brace Socket wrench handle
22-4
TM 9-243

RADIO AND POCKET SCREWDRIVERS SCREW STARTER OR GIMLET
A radio screwdriver (1) has a round blade that is 1-1/2 inches long. Its use is restricted to very small screws generally used in the construction of radio chassis. The pocket screwdriver (2) is also small, with a square blade that is 1-3/4 inches long. Both have pocket clips.
A screw starter or gimlet has a threaded tip. It is used to make a pilot hole in wood for wood screws.
SAFETY
WARNING HANDLE THE SCREWDRIVER CAREFULLY. A GREASY HANDLE COULD CAUSE AN ACCIDENT. DO NOT CARRY A SCREWDRIVER IN YOUR POCKET UNLESS IT HAS A POCKET CLIP. DO NOT USE A SCREWDRIVER FOR PRYING, PUNCHING, CHISELING, SCORING, OR SCRAPING. DO NOT USE A SCREWDRIVER NEAR A LIVE WIRE, TO CHECK A STORAGE BATTERY, OR TO DETERMINE IF AN ELECTRICAL CIRCUIT IS LIVE. DO NOT HOLD THE WORK IN ONE HAND WHILE USING THE SCREWDRIVER WITH THE OTHER. IF THE SCREWDRIVER SLIPS OUT OF THE SLOT, YOU WILL BE MOST LIKELY TO PUT A GASH IN YOUR HAND.
USING SCREWDRIVERS
NOTE The proper way to select and use a screwdriver is to always match the size of the screwdriver to the job and always match the type of screwdriver to the head of the screw.
22-5
TM 9-243
USING SCREWDRIVERS - Continued

PREPARING THE WORK SURFACE 3 Turn clockwise to screw in, counterclockwise to
unscrew.
4 Do not use a pliers to turn the screwdriver when

driving or removing screws that are hard to turn. For hard-to-turn screws, use a square blade screwdriver designed for heavy-duty work and a wrench which properly fits the blade.
USING AN OFFSET SCREWDRIVER
1 Before attempting to drive a screw into wood, you

first make a pilot hole (1) using a screw starter (gimlet) (2), an awl, a nail, or a drill.
2 Before attempting to drive a screw into sheet metal

you should make a pilot hole using a drill. However, lightweightsheet metal can bepierced with a nail or punch.
USING A SCREWDRIVER
1 Select the correct style and tip size for the screw
being used.
2 Insert the tip (1) in the screw slot. 3 In tight places you may have to alternate tips (1
and 2) to complete turning the screw.
1 Insert the screw (1) in the pilot hole. Insert the

screwdriver tip (2) in the screw slot of the screw as shown.
2 Keep the screwdriver in line with the screw as

shown. You may want to use your other hand to keep the blade steady.
22-6
TM 9-243

USING AN OFFSET RATCHET SCREWDRIVER
1 Select the correct size tip for the screw head.
Pull the lever to the right or left, for installation or removal of the screw. This allows the screw to be driven without having to remove the tip from the screw head.
3 Set selector lever (3) as shown.
USING A SPIRAL RATCHET SCREWDRIVER

NOTE These screwdrivers come in several styles. Some have the different size bits stored in the handle.
4 Insert the tip in the screw slot. Hold the screwdriver

blade as shown. Move handle (4) back and forth to install or remove a screw.
1 Select the correct size tip for the screw head being
used. 2 Install tip (1) in screwdriver by pulling back on metal shell (2). When tip is seated, release the shell to lock it into place.
22-7
TM 9-243

USING A JEWELERS SCREWDRIVER
1 Hold screwdriver as shown, with forefinger on

rotating head (1). CAUTION Be sure the screwdriver fits the screw. If the screw is too large for the screwdriver tip, the tip will be damaged.
2 Insert the tip of the screwdriver in the screw slot (2).

Turn the screwdriver, between the thumb and middle finger, clockwise to screw in, counterclockwise to unscrew.
CARE OF SCREWDRIVERS
1. When a screwdriver becomes nicked, or the edges become rounded, or when other damage occurs so that it does not fit a screw slot, it can be reground or filed. The sides must be parallel to keep the tool from lifting from the screw slot and the tip must be square, at right angles to the sides and to the blade. Do not expose a screwdriver to excessive heat, as it may reduce the hardness of the blade. Replace a screwdriver that has a worn or damaged handle or rounded tip. After use, wipe screwdriver clean and place in rack or tool box. For long-term storage, apply rustpreventive compound to all metal surfaces and store in a dry place. TIP SIDES ARE GROUND PARALLEL TIP SIDES ARE GROUND TO SHAPE OF GRINDING WHEEL TIP SIDES ARE GROUND AT AN ANGLE 7. 5. Screwdrivers used in the shop are best stored in a rack. This way the proper selection of the right screwdriver can be quickly made and fewer injuries will result. A poor fitting screwdriver will damage the screw head, slip off the screw, and cause personal injury. Use a screwdriver that has parallel sides and exactly fits the screw slot. Never pound on a screwdriver with a hammer. Do not use a screwdriver as a chisel.
6.
2. 3. 4.
RIGHT
RIGHT
WRONG
22-8
TM 9-243
Chapter 23 MANUAL DRILLS

The Types and Uses section provides you with a list of some of the types of drills. These pages should help you select the right drill to do the job. The Using section tells you how to use the drill to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item
Page
TYPES AND USES . . . . . . . . . . . . . . . . . Brace drill . . . . . . . . . . . . . . . . . . . . . . . . . Breast drill . . . . . . . . . . . . . . . . . . . . . . . . . Hand drill . . . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23-2 23-2 23-2 23-2 23-3 23-4
23-1
TM 9-243
TYPES AND USES

BRACE DRILL
the hole. To change from low speed to high speed, move the drive handle and speed gears from the bottom hole to the top hole. High speed position is illustrated. Some drills have a slot instead of two holes. The side handle provides a way to steady the drill and insure that the bit is boring a straight hole. The speed gears determine the speed at which the drill rotates. They are connected through linkage to the pinion gears. The pinion gears turn the chuck and drill. The breast drill is used to drill holes in wood, plastic, concrete, and small gage sheet metal.
HAND DRILL
The brace drill is made up of the following parts: head (1), crank (2), crank handle (3), ratchet mechanism (4), and chuck (5). The brace is used to drill holes in wood and with a screwdriver bit, remove and install screws.
BREAST DRILL
The breast drill is made up of the following parts: breast plate. (1), drive handle (2), speed shifter (3), side handle (4), speed gears (5), pinion gears (6), and chuck (7). The adjustable breast plate provides a base for the user to lean against while using the drill. The speed shifter provides a means of selecting high speed or low speed. This allows the operator to start a hole at slow speed, 1:1 ratio, preventing marring of the surface, then shifting to high speed, 3-1/2:1 ratio, to finish drilling
The hand drill is made up of the following parts: handle (1), drive handle (2), side handle (3) pinion (4), gear wheel (5) and chuck (6). The handle provides a storage area for drill bits. The side handle may be used to steady the drill when drilling in soft wood. The pinion turns the chuck and drill. Through mechanical linkage, the gear wheel transfers the driving force from the drive handle to the chuck. Hand drills are used to drill holes in wood and sheet metal.
23-2
TM 9-243
USING A BRACE DRILL

NOTE The following procedure is for a bit of a fixed size from 1/4 inch up to a 1 inch maximum.
Mark (1) with a pencil where hole is to be drilled.
Center bit over pencil mark. Push down on head (5) and turn crank (6) until bit goes through the board. NOTE Ratchet mechanism (7) may have to be set.
Open chuck (2) and insert bit (3) between jaws (4). Tighten chuck (2), securing bit (3).
Reverse the ratchet mechanism (7), then turn crank and pull up on head to remove bit.
5 Open chuck and remove bit. Close chuck.
23-3
TM 9-243
USING AN EXPANSIVE BIT

NOTE Expansive bits are available in two sizes, one from 5/8 inch to 1-3/4 inches and the other from 7/8 to 3 inches.
1.
Loosen retaining screw (1). Slide adjustable blade (2) to the desired width using built-in scale (3) or a 6-inch machinists rule.
2.
Tighten retaining screw (1) and refer to USING A BRACE steps 1 through 5, page 23-3.
CARE OF MANUAL DRILLS

Apply a light coat of oil to all metal surfaces. With a rag, clean gear teeth of dirt, wood and metal shavings and apply a light coat of oil. Hang manual drills on a rack or store in a safe, dry place.
23-4
TM 9-243
Chapter 24 SCREW AND TAP EXTRACTORS

The Types and Uses section provides you with a list of some of the types of extractors. These pages should help you select the right extractor to do the job.
The Using section tells you how to use the extractor to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . Screw extractors . . . . . . . . . . . . . . . . . . . Tap extractor . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24-2 24-2 24-2 24-3 24-3
24-1
TM 9-243
TYPES AND USES

SCREW EXTRACTORS
Screw extractors are used to remove broken screws without damaging the threads or surrounding material. There are two basic types of screw extractors, the straight-flute type and spiral-tapered type.
TAP EXTRACTOR
The tap extractor is usually of the flute type and requires the use of a wrench to turn the tap. It is used for removing taps with no external area.
The straight-flute type requires the following tools to drill a pilot hole in the screw: a twist drill (1), a drill guide (2), and a turn nut (3).
The spiral-tapered type requires a twist drill for drilling a pilot hole.
24-2
TM 9-243
USING A SPIRAL TAPERED SCREW EXTRACTOR

NOTE The following task is not the only use of a screw extractor.
WARNING WEAR PROPER EYE PROTECTION.
Insert extractor (3) in the drilled hole.
Drill a hole in the broken screw (1). Use a drill size guide (2) if available. If one is not available, drill the hole slightly smaller than the diameter of the extractor. (When drilling larger screws it may be necessary to drill a small pilot hole first, then a larger hole).
Remove the broken screw by turning the extractor counterclockwise. The extractor may be turned using a tap wrench or open end wrench (4).
CARE OF EXTRACTORS
1. Keep extractors clean and lightly oiled. 2. Store in case provided or wrap individually to protect the extracting edges.
24-3/(24-4 blank)
TM 9-243
Chapter 25 WRENCHES
The Types and Uses section provides you with a list of some of the types of wrenches. These pages should help you select the right wrench to do the job.
The Using section tells you how to use the wrench to perform the desired function, The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . 25-2 Open-end wrenches . . . . . . . . . . . . . . . . 25-2 Box wrenches . . . . . . . . . . . . . . . . . . . . . . 25-3 Combination wrenches . . . . . . . . . . . . . . . 25-4 Socket wrenches . . . . . . . . . . . . . . . . . . . 25-5 Socket wrench handles, extensions and adapters . . . . . . . . . . . . . . . . . . . . . 25-6 Special purpose socket wrenches . . . . . 25-7 Crowfoot wrench . . . . . . . . . . . . . . . . . . . 25-9 Hex key wrench . . . . . . . . . . . . . . . . . . . . . 25-9 Plug wrenches . . . . . . . . . . . . . . . . . . . . . 25-9 Adjustable open-end wrench . . . . . . . . . 25-10 Clamp pliers . . . . . . . . . . . . . . . . . . . . . . . 25-10 Monkey and auto wrenches . . . . . . . . . 25-10 Pipe wrenches . . . . . . . . . . . . . . . . . . . . . 25-11 Torque wrenches . . . . . . . . . . . . . . . . . . . 25-11 Spanner wrenches . . . . . . . . . . . . . . . . . 25-12 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . 25-13 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-14 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-18
25-1
TM 9-243
TYPES AND USES

A wrench is a tool specially designed to tighten or loosen nuts, bolts, studs, and pipes. Wrenches are forged from steel alloy to prevent breakage. There are many different types of wrenches. Each type has its own use. By using the properwrench for the task to be done, you will not break the wrench, damage the equipment, or cause personal injury. The following section is intended to give you information on the different wrench types.
OPEN-END WRENCHES
The engineers double open-end wrench has different size openings on each end. This type of an arrangement permits a smaller number of wrenches to complete a set. The engineers double open-end wrench is also used to reach behind or below blind surfaces.
All open-end wrenches have open jaws on one or both ends of the wrench. Most jaw openings are offset from the shank portion of the wrench by 15 degrees. The wrench length is determined by the size of the jaw opening. Some of the more common types of open-end wrenches and their uses are listed below.
The construction wrench combines the open-end jaw with a long tapered shank providing a wrench/alignment punch combination. The construction wrench is used in the building trades and on heavy objects which require alignment before fastening. The engineers single open-end wrench has a long smooth shank providing the user with a better gripping surface. It is used to reach behind or below blind surfaces.
25-2
TM 9-243

OPEN END WRENCHES (Cont) BOX WRENCHES
The S-Shape wrench has a 22-1/2 degree offset. It is used to reach around obstructing objects.
A box wrench surrounds the nut, bolt head, or stud on all sides. It is available with both 6-point and 12-point openings. The 12-point opening is more common, as it may be used on both square and hexagonal bolt heads. Box wrench openings are offset from the shank by 15 degrees. A box wrench should be used whenever possible, as it provides the best protection to both the user and the equipment. The major disadvantage of the box wrench is that there must be enough clearance above and around the bolt head to place the wrench over the bolt head. The length of the box wrench depends upon the size of the opening. Some of the more common types of box wrenches and their uses are shown below and on page 25-4.
Ignition wrenches have the same size jaw opening on both ends. However, one end of this wrench is offset 15 degrees and the other end is offset 60 degrees. Ignition wrenches are smaller in size, as they are used to remove components of automotive ignition systems. The most common box wrench is the double offset box wrench. It comes with a different size opening at each end. The double offset wrench is used to remove normal nuts and bolts.
25-3
TM 9-243

BOX WRENCHES (Cont)
wrench/alignment pin combination. It is usually used on heavy structural construction (bridge girders, building beams, etc.).
The half-moon wrench has different size openings at each end and has a curved shank. The half-moon wrench is used when it is necessary to reach around objects in tight spaces.
Ratchet-box wrenches are either reversible or nonreversible. The ratchet-box wrench does not have to be lifted up and repositioned each time the shank has reached its maximum travel between two obstructions. The ratchet-box wrench provides an easy means of removing and/or installing nuts or bolts which are not under strain. These wrenches should not be used to torque down or to free nuts or bolts.
COMBINATION WRENCHES
The split-box wrench is a 12-point wrench with 2 points cut away. The split-box wrench is used on pipe unions or couplings where you want the protection of a box wrench, but need to slide the wrench around a pipe.
The structural-tapered handle wrench combines a box wrench opening with a tapered shank to produce a box
The combination wrench combines the best features of the open-end and box wrench into a single wrench. The size opening on the wrench is the same on both ends, but one end has a box head and the other end has an open-end head. The length of the wrench varies with the size of the head. The most common opening is offset from the shank by 15 degrees. They are used to remove common-size nuts and bolts.
25-4
TM 9-243

SOCKET WRENCHES
The socket wrench consists of a round metal sleeve with a square opening in one end for insertion of a handle, and a 6-point or 12-point wrench opening in the other. They are available in both common (short) and deep (long) lengths. The length of the socket does not determine its size. Socket wrenches usually come in sets. The square or drive end may vary in size from 1/4 to 1 inch. In socket sets, the drive end determines the size; for example, a 1/4-inch drive set may contain nine sockets ranging in size from 3/16 inch through 1/2 inch. In 3/8-inch drive, the smallest socket would be 3/8 inch. This overlap in size allows better control by the user and prevents breakage of either the socket or the equipment from using the wrong size handle.
A universal joint socket and spark plug socket are examples of specially designed sockets. The universal joint socket is used when it is necessary to reach around an object. The spark plug socket has a rubber insert. This insert protects the ceramic insulator when removing and/or installing the spark plug. All sockets must be used with some type of handle. Sockets are used to remove and/or install common-size nuts or bolts.
25-5
TM 9-243

SOCKET WRENCH HANDLES, EXTENSIONS AND ADAPTERS
Ratchet handles may have either a straight-head or a flex-head. Both types have a selection lever on the top of the head to determine the direction of drive. The flexhead is used to go around objects. Both types are used with socket wrenches for rapid removal of nuts or bolts.
The speed handle has a brace-type shaft with a revolving grip on the top. It is used for rapid removal and/or installation of nuts or bolts, which are out in the open and have little or no torque.
The sliding T-Bar handle has a single head which may be adjusted along a bar handle. It has two spring-loaded balls, one for keeping the bar in the head and the other for keeping the socket on the head. The sliding T-Bar is used for increased leverage or for working around other objects.
A hinged handle has a hinged adapter on one end which may be rotated in 90 degree steps. The hinged handle is used when additional leverage or torque is needed to loosen nuts or bolts.
25-6
TM 9-243

SOCKET WRENCH HANDLES, EXTENSIONS AND ADAPTERS (Cont)
The spin-type screwdriver grip handle has a plastic or wood handle. It is used to remove and/or install small nuts and bolts.
The socket wrench adapter is used to change the drive size between the socket and the handle. It usually increases or decreases the fractional size by one (1/4 inch to 3/8 inch). The socket wrench adapter is used to increase or decrease the drive end of a particular handle allowing it to be used with two different socket sets.
SPECIAL PURPOSE SOCKET WRENCHES
Extensions are either rigid or flexible. They range from 2 to 17 inches in length. Extensions may be used with any socket handle combination to gain clearance above nut or bolt.
The ratcheting adapter converts a non-ratcheting handle into a ratchet drive. It is used for quick removal of nuts or bolts.
The four-way socket wrench has four nonremovable sockets attached to four arms. Each of the sockets is a different size. The four-way socket wrench is usually used to remove or install the wheel stud nuts of a vehicle. The handle construction provides extra leverage when loosening and tightening the stud nuts.
25-7
TM 9-243

SPECIAL PURPOSE SOCKET WRENCHES (Cont)
Stud removers may be either the cam-operated type or the wedge type. They are used to remove studs from their seats for replacement. A single stud remover can be adjusted to remove different size studs.
The 90-degree offset handle socket wrench has a fixed socket at the end of a bent handle. It is used for removing and/or installing a nut or bolt which may not be reached with a box or combination wrench.
The cam-operated type uses a concentric cam to get a grip on the stud. The cam is tightened on the stud through mechanical linkage between the drive shank and the cam.
The T-handle socket wrench has a fixed T-handle above a fixed socket wrench. The T-handle socket wrench has many uses. One of the more common uses is for shutting off or turning on water or gas lines. The T-handle permits the operator to apply the turning force required to operate the valve.
Wedge-type stud removers are made of a socket housing and two metal wedges. The socket is placed over the stud to be removed and the wedges are driven into the socket to hold the stud. The socket housing is now turned with a handle to remove the stud. The screwdriver-type socket wrench has a socket fixed on the bottom of a screwdriver handle. They are used to remove and/or install small nuts and bolts.
25-8
TM 9-243

CROWFOOT WRENCH PLUG WRENCHES
There are three basic types of plug wrenches, the bartype, the multiple plug wrench, and the socket-type. Plug wrenches are used to remove and/or install drain plugs.
The crowfoot wrench is an open-end wrench head which is turned with a socket handle. It is used to remove and/or install nuts or bolts. It is also used where an obstruction would prevent the use of a regular socket.
Bar-type plug wrenches may be either square or hexagonal and are about two inches long. A combination wrench or socket must be used to turn the plug.
HEX KEY WRENCH (SHORTER SECTION)
The multiple plug wrench combines several plug ends on a common handle.
The hex key wrench is an L-shaped, six-sided wrench. Both ends of the "L" are the same size so you can turn the wrench either to gain access to the screw head or to obtain a leverage advantage. The hex key wrench is used to remove and/or install hex head screws.
Socket-type plug wrenches are usually combined in sets with an assortment of handles. The set will contain several sizes.
25-9
TM 9-243

ADJUSTABLE OPEN-END WRENCH MONKEY AND AUTO WRENCHES
The adjustable open-end wrench has one fixed jaw and a movable or adjustable jaw. The adjustable jaw is set against the face of the nut by turning a knurled worm gear. Care must be exercised when using an adjustable wrench. Always use the fixed jaw for applying pressure to tighten or loosen nuts or bolts. Adjustable wrenches are used to remove and/or install nuts, bolts, and studs when the correct size wrench or socket is not available.
CLAMP PLIERS
The clamp pliers are generally used more as a wrench than as a pair of pliers. It has a fixed jaw and handle which contains an adjustment screw for the movable jaw. The other handle is in two sections, one section to apply pressure and to lock the pliers, and the other section, when pulled, to release the grip. Clamp pliers are used to hold or clamp nuts and bolts which have been rounded off by using the wrong size wrench.
The monkey and auto wrenches are similar and have one fixed jaw and an adjustable jaw which moves along the handle by turning a knurled worm gear. Monkey and auto wrenches are used to install or remove odd size nuts and bolts. An adjustable wrench must be used with care. Always apply pressure against the fixed jaw.
25-10
TM 9-243

PIPE WRENCHES
There are three basic types of pipe wrenches, the stillson wrench, the strap wrench, and the chain wrench. They are all used to connect or break pipe joints or to turn cylindrical parts.
The stillson pipe wrench has a fixed jaw which is on the end of the handle and an adjustable jaw at the top of the wrench. Adjustment is made by turning a knurled adjusting screw which moves the jaw. Always pull the pipe fitting towards the fixed jaw. The serrated (grooved) jaws of the stillson wrench will mar soft pipe.
Chain pipe wrenches have a section of bicycle-type chain permanently attached to the handle. The upper section of the head has teeth which mate with the links of the chain. The chain is wrapped around the pipe and pulled over the head section of the wrench to grip the pipe. Chain pipe wrenches will scratch the surface of the pipe. TORQUE WRENCHES Torque wrenches are designed to measure the specific degree of tightness of nuts or bolts. Torque wrenches are considered precision instruments and therefore must be calibrated at regular intervals. Torque wrenches are used for final tightening of nuts or bolts. Torque wrenches are normally calibrated in a right-hand direction only. If a unit is required to perform torquing operations in a left-hand direction, they must request that the supporting calibration facility calibrate the torque wrench in both directions.
Strap pipe wrenches have a leather or canvas strap which is attached to the handle. The strap is looped around the pipe and back through the handle to grip the pipe. The strap pipe wrench will not scratch the surface of the pipe.
A dial torque wrench has a head which contains the drive element and a dial for reading the exact amount of torque. Change 1 25-11
TM 9-243

TORQUE WRENCHES (Cont)
torque wrench. This type of torque wrench is used for tightening nuts and bolts requiring 200 or more foot pounds of torque. NOTE A special feature of this type of torque wrench is that it is possible to loosen as well as tighten nuts and bolts.
SPANNER WRENCHES
Two basic types of spanner wrenches are the hook-type and the pin-type. Hook-type spanner wrenches are either fixed or adjustable and are normally used to tighten fire hoses or similar couplings which have a protruding lip. Pin-type spanner wrenches have pins protruding from the handle which fit into holes in the coupling or plate to be tightened or loosened. Spanner wrenches are special purpose wrenches and are to be used only for their intended purpose.
A scale torque wrench has a rod which runs parallel to the handle and the drive element. This rod moves across the scale to the right or left as torque is applied.
POWER TORQUE WRENCH
HOSE COUPLING PIN
FIXED HOOK
ADJUSTABLE HOOK
Three kinds of hook-type wrenches include the hose coupling pin, for tightening and loosening hose couplings, the fixed hook, for tightening or loosening couplings with protruding rims or edges, and the adjustable hook-type. The adjustable hook-type is similar to the fixed hooktype. However, it may be adjusted around objects and fastened before use.
Using a powerful gear train, the power torque wrench is completely mechanical in operation. The power torque wrench is operated by a hand crank. The torque is calibrated in foot pounds, which is shown by a dial indicator on the top face of the power
25-12
Change 1
TM 9-243

SPANNER WRENCHES (Cont)
There are two basic pin-type wrenches. The fixed-pin face has been designed to fit a particular pattern and is nonadjustable. The fixed-pin face is used to remove protective cover plates. The adjustable pin face has two arms joined at a common point. The other end of the arms contain pins which may be engaged in the holes of a cover plate for removal.
SAFETY
1. Wrenches should fit the nuts or bolts they are to loosen or tighten. Never turn adjustable wrenches so that the pulling force is applied to the adjustable jaw. Do not attempt to extend the handle in any way to increase the leverage on a wrench. Increased leverage may damage the wrench or the work. Apply penetrating oil to rusted nuts and/or bolts that resist turning. Allow time for oil to penetrate before attempting to turn. Do not strike wrenches with hammers to tighten or loosen nuts or bolts. 6. Do not exert a hard pull on a pipe wrench until it has gripped the work firmly. Remember to pull on the wrench, when possible, in order to protect your knuckles in case the wrench slips. Return all wrenches to their proper places upon completion of each job. This eliminates the possibility of leaving them where they can injure someone. Always keep the wrench in good condition, clean and free from oil or grease. Otherwise it may slip, resulting in possible serious injury to you or damage to the work.
2.
7.
3.
8.
4.
9.
5.
25-13
TM 9-243
HOW TO USE A BOX WRENCH
1 Select the size of wrench that fits the nut or bolt. 2 Place the wrench (1) on the nut or bolt (2). Swing the
wrench clockwise to tighten and counterclockwise to loosen for a right hand threaded nut or bolt. Reverse the above for a left hand threaded nut or bolt.
3 If there is insufficient room to swing the wrench in a

full circle, lift it completely off the nut when it comes to the limit of the swing, and place it in a new position, permitting another swing. A swing through of a 15 degree arc is usually sufficient to continuously loosen or tighten a nut or bolt.
4 After the nut is tight, give it a final tightening.
USING A SOCKET WRENCH
1 Select the size of socket (1) that fits the nut or bolt to
be turned and push it onto the handle (2) which is best suited to the job.
desired direction. (The socket need not be raised from the nut at the end of each swing.)
4 When a tight nut is to be loosened or a nut is to be

set up, the nut hinged handle (3) can be swung at right angles to the socket to provide the most leverage. At the point where the nut turns easily, the handle can be swung to a vertical position and twisted rapidly between the fingers in the same manner as a screwdriver.
2 If there is room to swing, use the ratchet handle.

(The handle may be made to ratchet in one direction for tightening work and in the other direction for loosening work.)
3 Swing the handle back and forth to turn the nut in the
25-14
TM 9-243
USING AN ADJUSTABLE OPEN-END WRENCH

1 Place the wrench (1) on the nut (2) so that the force
used to turn it is applied to the stationary jaw side of the wrench.
2 Tighten the knurled adjusting nut (3) until the

wrench fits the nut as tightly as possible. CAUTION If the wrench does not fit tightly, it will slip and round the corner of the nut.
3 Swing the wrench clockwise to tighten the nut. 4 After the nut is tight, set it up (final tightening).
USING AN ADJUSTABLE STRAP PIPE WRENCH
1 Loop the strap (1) around the pipe (2) in the opposite direction to that in which the pipe is to be rotated. NOTE The jaw (5) at the end of the shackle will seat against the strap and, as the handle is pulled, the strap will tighten and turn the pipe.
2 Slip the end of the strap through the shackle (3) and
draw it up tightly.
3 Pull the handle (4) to turn the pipe in the desired

direction until the desired tightness is obtained.
25-15
TM 9-243
USING THE TORQUE WRENCH

1
Select proper size socket wrench (1) and attach to torque wrench square drive (2). wrench handle in the desired direction to tighten the work. NOTE The tightening torque will be indicated on the dial or scale (3), depending on the type of the torque wrench used.
2 Place socket wrench on work and pull the torque
Remove the wrench when the torque on the dial or scale is reached.
USING THE POWER TORQUE WRENCH
1 To tighten a nut, set the knurled ratchet indexer (1)

NOTE The following procedure is not the only application for the power torque wrench. However, use of this tool is basically the same regardless of model or application. (located on the front of the wrench) in the same direction the handle will be turned.
2 3
Install applicable socket (2) onto the nut to be tightened. Install square drive bar (3) into the socket.
25-16
TM 9-243
USING THE POWER TORQUE WRENCH - Continued
5
CAUTION Different reaction adapters are required for various operations. Be careful to use the correct reaction torque adapter. Failure to do so will render torque wrench useless and can damage the equipment.
Install power wrench (6) onto square drive bar and reaction torque adapter. Rotate power wrench until the reaction torque adapter engages a fixed point.
4 Install reaction torque adapter (4) over drive bar and

socket as shown.
CAUTION Do not use impact wrench of any kind to operate this wrench. NOTE When installing power torque wrench, make sure the two locking pins (5) underneath the wrench are firmly engaged to the reaction torque adapter.
6 Install the crank handle (7) into the square input (8)
and turn in the same direction as the output must turn.
7 Continue to turn crank until torque indicator (9)

shows the desired torque reading.
25-17
TM 9-243
USING THE POWER TORQUE WRENCH - Continued

8 After obtaining the desired torque, turn the crank in
the opposite direction until the torque indicator returns to zero (green band). This will remove the holding pressure on the wrench.
9 Remove the wrench, adapter, and socket. 10 To loosen a nut, repeat steps 1 through 6.
NOTE Normally, torque will build up in the wrench until break-away torque is reached. As the torque load is released, the indicator will reverse direction.
11 12
Continue to turn crank until indicator returns to O. Remove the wrench, adapter, drive bar and socket.
USING A SPANNER WRENCH
1 2 3 4 5
Insert the pins or lugs into the pin holes of the part. Keep the pin face of the wrench flush against the surface and turn the wrench. Exert enough force against the wrench so that the pins do not pop out of the holes. Make certain that the pins fit the holes and the force is applied with the handle perpendicular to the work. Remove the wrench when desired tightness is obtained.
CARE
1 Clean all wrenches after each use. 2 Wrenches that come in sets should be returned to
their cases after use. b. For the rest of the torque wrenches (unless your local SOP states differently) zero them before you store them. This takes the pressure off the spring, and the wrenches will last longer and give better service.
2.1 Store torque wrenches as follows:

a. When storing the micrometer-type torque wrenches or beam-type torque wrenches, check to make sure they are returned to zero before storing. 25-18 Change 1
3 4
Apply a thin film of oil to the metal parts of all wrenches before storing them. Remove oil before use to prevent injury or damage. For long-term storage, the wrenches should be covered with a rust-preventive compound and carefully stored in a dry place.
TM 9-243
Chapter 26 CHISELS
The Types and Uses section provides you with a list of some of the types of chisels. These pages should help you select the right chisel to do the job. The Using section tells you how to use the chisel to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . 26-2 Woodworkers chisels . . . . . . . . . . . . . . . . 26-2 Machinists chisels . . . . . . . . . . . . . . . . . . . 26-2 Track chisel . . . . . . . . . . . . . . . . . . . . . . . . 26-2 Rivet buster chisel . . . . . . . . . . . . . . . . . . 26-2 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 - 3 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 - 5
26-1
TM 9-243
TYPES AND USES

WOODWORKER'S CHISELS
There are two types of woodworkers chisels. The socket type has a blade and socket handle forged of high carbon steel in a single casting. The wooden handle is inserted into the socket. This type of chisel is used to cut and pare off wood. Generally socket-type chisels are used for heavier cutting when a hammer or mallet may be required for additional driving force.
The cape chisel has a small solid point on one end and a flat base on the other end. It is used for cutting keyways or slots in metal, and square corners.
The roundnose chisel has a ground edge on one end and a flat base on the other end and an octagon-shaped stock. It is used to align drilled holes, cut channels, cut oil grooves and similar work. The tang-type chisel is forged in a single casting. The handle is drilled and inserted over the tang and reinforced with a metal band. The tang-type chisels are also used to cut and pare wood. However, the driving force required is hand pressure only.
TRACK CHISEL
MACHINISTS CHISELS
The track chisel has a beveled point on one edge and a flat face on the other end. The cutting edge is 1-3/8 inches wide; the overall length is 10-1/2 inches and it weighs 5-1/2 pounds. The track chisel is used with a 22-inch sledge hammer to remove track bolts, boiler rivet heads and cut rail when a saw or cutting torch is not available.
Machinists chisels are designed to cut and shape cold metal and are usually struck with a hammer. The flat or cold chisel is composed of hardened steel and has a tapered cutting edge on one end and a flat base on the other end.
RIVET BUSTER CHISEL
The diamond point chisel has a solid point on one end and a flat base on the other end. It is used for drawing and cutting holes in flat stocks and to cut V-grooves.
The rivet buster chisel has a single ground flat cutting edge on one end and a flat face on the other end. The cutting edge is about 3/4 inch wide and the overall length is about 9 inches. It is used for cutting off chassis rivets and in other difficult places which cannot be reached by other chisels.
26-2
TM 9-243
USING A WOODWORKERS CHISEL

The following procedure is designed for using a woodworkers chisel. WARNING NEVER CUT TOWARD YOURSELF WITH A CHISEL CAUTION Use short, rapid mallet blows to control depth and length of cut.
WARNING WEAR EYE PROTECTION. KEEP BOTH HANDS BACK OF THE CUTTING EDGE AT ALL TIMES.
4 Start your cut about 1/8 inch from the guide line (1). 1 With rule and pencil, mark area (1) to be cut with the
chisel.
Using a chisel and mallet, make your cut toward the center (the waste area) to protect the edge. Make small thin cuts. This prevents breaking or splitting of the work. Check your guide marks often to prevent overcutting.
Examine the grain of the wood, and place securely in a vise (2) so you are cutting with the grain. The wood should not be able to move in any direction.
Rough cuts are made with bevel side down (3) while smooth finishing cuts (4) are made with bevel side up.
Remove the last 1/8 inch using chisel and mallet to complete the job.
26-3
TM 9-243
USING A MACHINISTS COLD CHISEL
WARNING WEAR EYE PROTECTION. NOTE The following procedure is designed for using a machinists cold chisel. However, cutting round stock is not the only use for this type of chisel.
3 4 1 2
With a rule and marking pencil measure desired length and mark. Place mark on a hard steel surface (1) (anvil, closed vise jaws, etc.).
Place cutting edge (2) of chisel on the mark with chisel straight up and down. Lightly strike the chisel with a hammer (3) and check chisel mark to be sure you are cutting on the desired mark.
Continue striking chisel with the hammer until cut is through the round stock. A larger diameter stock is cut the same way except it is turned over after the cut is about half way through the rod.
26-4
TM 9-243
USING A RIVET BUSTER CHISEL
WARNING WEAR EYE PROTECTION. The following procedures are designed for using a rivet buster chisel.
2 Grip the chisel firmly and strike chisel head (3) with
a machinists or sledge hammer. (4).
1 Place cutting edge (1) of the chisel firmly against the

rivet shaft (2) between the head and the metal.
Continue striking chisel head until rivet head has been cut off.
CARE OF CHISELS
1. 2. Protect the cutting edges by installing protective covers. Store in racks or where they may not be chipped or broken. 3. 4. Lubricate with a light coat of oil before storing. Regrind broken or chipped edges before using.
26-5/(26-6 blank)
TM 9-243
Chapter 27 PUNCHES
The Types and Uses section provides you with a list of some of the types of punches. These pages should help you select the right punch to do the job.
The Using section tells you how to use the punch to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . Center punch . . . . . . . . . . . . . . . . . . . . . . Drift punch . . . . . . . . . . . . . . . . . . . . . . . . . Alignment punch . . . . . . . . . . . . . . . . . . . Drive pin punch . . . . . . . . . . . . . . . . . . . . Prick punch . . . . . . . . . . . . . . . . . . . . . . . . Starting punch . . . . . . . . . . . . . . . . . . . . . Grommet inserting punch . . . . . . . . . . . . Catapunch . . . . . . . . . . . . . . . . . . . . . . . . . Metal cutting punch . . . . . . . . . . . . . . . . . . Tinmens hollow punch . . . . . . . . . . . . . . . Sheet metal punch . . . . . . . . . . . . . . . . . . Lever punch . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27-2 27-2 27-2 27-2 27-2 27-2 27-3 27-3 27-3 27-3 27-3 27-3 27-3 27- 4 27-6
27-1
TM 9-243
TYPES AND USES

There are two basic types of punches; solid (1) which are the most common, and hollow (2) which are usually designed for punching holes in leather, paper, and other similar materials. Solid punches are used to mark metal, drive pins, align holes and to do other similar jobs.
DRIFT PUNCH
The drift punch has a narrow, tapered flat point. The points range in size from 1/8 to 1/2 inch in diameter with an overall length from 7 to 9 inches. Drift punches may be used to remove shafts, pins, rivets (after heads have been removed), and to align small parts.
ALIGNMENT PUNCH
CENTER PUNCHES
There are two types of center punches, both used for starting drill holes.
The alignment punch has a narrow, tapered flat point. The points range in size from 1/8 to 1/2 inch in diameter with an overall length of 12 to 15 inches. Alignment punches are used to line up mating parts for assembly. Make sure the punch is large enough for the job. A punch that is too small may bend or break.
DRIVE PIN PUNCH
The hand-held type has a narrow, cone-shaped point terminating in a sharp, conical tip. Hand-held types; range from 1/8 to 5/8 inches in diameter and from 3 to 6 inches long. The hand-held punch must be struck with a hammer.
The drive pin punch has a flat tip which may be tapered. Points may range in size from 0.03 to 1/2 inch and are from 3 to 6 inches long. Standard drive pin punches usually come in sets of nine. Drive pin punches are used to remove straight or tapered pins. Make sure the right size punch is used for the pin being removed.
PRICK PUNCH
The automatic type has an adjustable regulator for determining the impact of the punch and also has interchangeable points. The automatic punch contains a tension spring for marking without the use of a hammer.
The prick punch has a long, conical-shaped point and ranges from 4 to 5 inches in length overall. It is used to mark soft metal.
27-2
TM 9-243

STARTING PUNCH METAL CUTTING PUNCH
The starting punch has a strong tapered point capable of resisting applied force. It is used to start the removal of a pin from an assembly.
GROMMET-INSERTING PUNCH
The metal cutting punch has an open, sharpened edge on one end and a solid shaft on the other end. The center portion of the punch is bowed for catching the metal scrap. The metal cutting punch ranges in size from 1/4 inch to 1 inch. Metal cutting punches are used to punch holes in thin sheet metal and require the use of a mallet or machinists hammer.
TINMENS HOLLOW PUNCH
The tinmens hollow punch has a solid metal shank terminating in a sharpened, hollowed end. It is used to punch holes through thin sheet metal.
SHEET METAL PUNCH

The grommet-inserting punch consists of two parts. The solid punch part has a tapered point and a flat shoulder. The round die part has flat ends with a bored hole in one end to receive the point of the punch. Grommetinserting punches are used to form the flange on grommets which are installed along the edges of flags, sails, mail bags, and similar items.
CATAPUNCH
The sheet metal punch is a heavy-duty steel punch approximately seven inches in length. It tapers to a fine point and must be struck to produce the hole. It is used to punch holes through sheet metal to take fastenings.
LEVER PUNCH
The catapunch consists of a pointed head mounted on a coiled spring shaft. It is used to mark centers on metal or wood without the use of a hammer.
The lever punch incorporates an interchangeable punch and a matching die or anvil. The die backs up the material, prevents distortion, and leaves a clean hole. This type of punch is used to punch small round holes near the edges of metal or leather material.
27-3
TM 9-243
USING A CENTER PUNCH
WARNING WEAR EYE PROTECTION NOTE The procedure which follows is only one of many uses of a hand-held center punch.
3 1
Mark the material to be punched with an "X" (1).
Position the punch upright and strike the blunt end (3) of the punch with a hammer (4).
Remove the punch and check your mark (5). If it is not in the center of the "X," or not deep enough, you will have to repeat the procedure.
2 Hold the punch (2) over the mark. Tilt it so that you
can align the tip with the center of the X.
27-4
TM 9-243
USING A DRIFT PUNCH

NOTE The removal of a pin from a shaft is only one of many uses for a drift punch.
WARNING WEAR EYE PROTECTION.
1 Select a punch which is slightly smaller than the pin

which is to be removed. Care must be taken when selecting a punch for removing a split pin. If the punch is too small, it may become lodged in the pin.
3 Catch the pin before it falls out of the Shaft. When

the pin is about half way out of the shaft, you can let go of the punch.
2 Hold punch (1) centered over pin (2). Tap punch

lightly with hammer (3). This should move the pin. It may be necessary to apply penetrating oil to the pin before it will move.
27-5
TM 9-243
USING AN ALIGNMENT PUNCH
WARNING WEAR EYE PROTECTION. DO NOT STRIKE THIS PUNCH WITH A HAMMER. NOTE The following procedure is for using an alignment punch. This tool, unlike others, has only one basic use.
2 Insert tip of punch (2) through hole in part A using

only hand pressure, and move punch and part A until you can get the tip of the punch into part B.
1 Select a punch having a smaller diameter than the

smallest hole (1) to be aligned.
3 4
Hold the assembled parts while you remove the punch. Proper use of an alignment punch prevents damaging threaded parts. Place screw in alined holes and tighten.
CARE OF PUNCHES
1. Clean punches with a clean rag after each use, 2 . Apply a light coat of oil before storing. 3. 4. Store punches in racks, tool rolls, or in your tool box so that the edges will not be damaged. Replace punches that have mushroomed ends.
27-6
TM 9-243
Chapter 28 FILES
The Types and Uses section provides you with a list of some of the types of files. These pages should help you select the right file to do the job.
The Using section tells you how to use the file to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . American pattern file . . . . . . . . . . . . . . . . Mill file . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pillar file . . . . . . . . . . . . . . . . . . . . . . . . . . . Round file . . . . . . . . . . . . . . . . . . . . . . . . . Square file . . . . . . . . . . . . . . . . . . . . . . . . . . Taper file . . . . . . . . . . . . . . . . . . . . . . . . . . . Three-square file . . . . . . . . . . . . . . . . . . . Warding file . . . . . . . . . . . . . . . . . . . . . . . . Curved-tooth file . . . . . . . . . . . . . . . . . . . . . Swiss pattern file . . . . . . . . . . . . . . . . . . . SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing the handle . . . . . . . . . . . . . . . .
28-2 28-2 28-2 28-2 28-2 28-2 28-2 28-2 28-3 28-3 28-3 28-3 28-4 28-5 28-6
28-1
TM 9-243
TYPES AND USES

Files are used for cutting, smoothing off, or removing small amounts of metal, wood, plastic, or other material. Files are made in various lengths, shapes, and cuts. Every file has five parts: the point (1), edge (2), face or cutting teeth(3), heel or shoulder (4) and tang (5). The tang is used to attach the handle on American pattern files. The tang is shaped into a handle and is usually knurled on Swiss pattern files. with one uncut edge. They are used to sharpen mill or circular saws, and for draw-filing or finishing metals.
PILLAR FILE
Pillar files are similar to hand files in general shape, but are much narrower. They are double-cut with one uncut edge. Pillar files are used to file in slots and keyways.
ROUND FILE
AMERICAN PATTERN FILE
Round files taper slightly toward the point. Bastard-cut files 6 inches and longer are double-cut. The second-cut files, 12 inches and longer, are double cut. All others are single-cut. Round files are used for filing circular openings or concave surfaces.
SQUARE FILE
American pattern files are generally used for fast removal of material and where a precision finish is not required. Grades of coarseness are bastard-cut for heavier work (1), second-cut (2) and smooth-cut (3) for finishing work, and dead smooth-cut (4) for an extra fine finish. American pattern files come with single-cut (5), double-cut (6), or curved-cut teeth (7). Single-cut files are used with light pressure for smooth surfaces or to put a keen edge on cutting surfaces. Double-cut files are used under heavier pressure and where a rougher finish is permissible. Curved-tooth files are cut in a contour across the face and are used to smooth surfaces on aluminum, bronze, lead, babbitt, zinc, and plastics.
Square files taper slightly toward the point on all four sides and are double-cut. They are used for filing rectangular slots and keyways.
TAPER FILE
Taper files, or triangular files, are tapered toward the point on all three sides. They are used for filing saws having 60 degree angle teeth. Taper files come in regular, slim, extra slim, and double extra slim and usually are single-cut.
THREE-SQUARE FILE
MILL FILE
Mill files are tapered to the point in width and thickness for about one-third of their lengths. They are single-cut
Three-square files are tapered toward the point on all three sides and are double-cut. They are used for filing internal angles, and for cleaning out square corners.
28-2
TM 9-243

WARDING FILE SWISS PATTERN FILE
Warding files are tapered to a point for narrow space filing. They have double-cut faces and singlecut edges. Warding files are used for lock repair or for filing ward notches in keys.
CURVED-TOOTH FILE
Curved-tooth files, also known as mill-toothed files, are generally used on aluminum and sheet steel and on flat or curved surfaces. They are also used for smooth, rapid work on bronze, lead, babbitt, zinc, and plastic.
Swiss pattern files are made to more exact measurements than American pattern files. They are primarily finishing tools used on all sorts of delicate and intricate parts. Swiss pattern files come in a variety of styles, shapes, sizes, and double and single cuts to insure precision smoothness.
Flat, flexible, curved-tooth files do not have tangs and are made for easy mounting on a file holder. The file holder is adjustable for concave or convex surfaces. Flat, flexible, curved-tooth files come in fine-cut and standard-cut teeth.
Flat, rigid, curved-tooth files are self-cleaning and used for filing flat surfaces on cast iron, lead, babbitt, aluminum, zinc, and plastic. They come in smooth-cut and standard-cut teeth.
These files are usually supplied in sets. The most common set consists of twelve assorted files in a set which are marking (half-round), square, slitting, knife, joint (round edge), crossing (oval), barrette, flat, equaling, half-round, three-square (triangular), and round. Swiss pattern files are made in seven cuts, Nos. 00, 0, 1, 2, 3, 4, and 6. They are most often used for fitting parts of delicate mechanisms, and for tool and die work.
Half-round, rigid, curved-tooth files are flat on one side and convex on the other. They are used for filing concave surfaces and bearings. They come with standardcut teeth.
SAFETY
1. If a file is designed to be used with a handle, do not attempt to use it without the handle. Holding the sharp tang in your hand while filing can cause serious injury. Do not use a file for prying. The tang end is soft and it bends easily. The body of the file is hard and very brittle. A light bending force will cause it to snap. 3. Do not hammer on a file. This is very dangerous because the file may shatter.
2.
28-3
TM 9-243
USING A FILE
SELECTING PROPER FILE
1. 2. 3. 4. For heavy, rough cutting, use a large, coarse, double-cut file. For finishing cuts, use a second or smooth-cut, single-cut file. When working on cast iron, start with a bastard-cut file and finish with a second-cut file. When filing soft metal, start with a second-cut file and finish with a smooth-cut file. 5. 6. 7. 8. When filing hard steel, start with a smooth-cut file and finish with a dead-smooth file. When filing brass or bronze, start with a bastard-cut file and finish with a second or smooth-cut file. When filing aluminum, lead, or babbitt metal, use a standard-cut curved-tooth file. For small work, use a short file. For medium-sized work, use an 8-inch file. For large work, use a file that is most convenient.
METHOD OF FILING
work on the return stroke, it will become dull much sooner than it should. 4. 5. 6. When filing soft metals, using pressure on the return stroke helps keep the cuts in the file clean. Use a rocking motion when filing round surfaces. When using a new file, applying too much pressure will cause the teeth to break off. Do not force the file. File slowly, lightly, and steadily. Too much speed and too much pressure causes the file to rock, rounding off the corners of the work.
1.
Clamp the work (1) securely in a vise so that the area to be filed is horizontal and is parallel to and projecting slightly above the vise jaws (2). Hold the file handle in one hand, thumb on top, and hold the end of the file with the fingers of the other hand.
DRAW FILING
1. Draw filing is used to produce a very smooth and true surface. Hold the file at right angles to the direction of the strokes, keeping your hands close together to prevent bending and breaking the file. Pressure should not be great and can remain the same on the back stroke as on the draw stroke. The speed of filing is not important. For extra smooth surfaces, wrap a piece of emery cloth around the file and stroke in the same manner.
2.
2.
3.
3.
When filing hard metals, apply pressure on the forward stroke only. Unless the file is lifted from the
28-4
TM 9-243
CARE OF FILES
1. 2. 3. A new file should be broken in by using it first on brass, bronze, or smooth iron. Never use a new file to remove the fins or scales on cast iron. Do not use a new file on a narrow surface such as sheet metal, because the narrow edge of the metal is likely to break off the sharp points on the file teeth. After using a new file, the teeth will clog up with metal filings. Using a clogged file will scratch the work. This condition is called pinning. One way to help prevent pinning is by rubbing chalk between the teeth before filing. The best method to keep the file clean is to use a file scorer and file cleaner brush.
4. 5. 6. 7.
12. 13. 14. 8. When cleaning a file with a file scorer (1), use a pulling motion, holding the file scorer blade parallel to the rows of teeth (2). Finish cleaning by brushing the file parallel to the rows of teeth, with the file cleaner brush. Do not throw files into a drawer or toolbox where they can rub against each other or against other tools. Store them in separate holders such as clips, straps, or in holes cut in a block of wood. Clean files often. 15. 16.
Never use a file without a securely attached handle (3), unless it is of the Swiss pattern type. Do not use files for any other use except filing. Do not oil files. This will cause the file to slide across the work, preventing fast cutting. Never strike the file against a vise or other object to remove filings. Use the file cleaner brush. Never store files with lubricants or rust-preventive compounds on them. Wrap each file in a waterproofed barrier wrapping paper and place the files in racks or boxes so that the faces or edges of the files will not touch each other.
9. 10.
11.
28-5
TM 9-243
CARE OF FILES - Continued

REPLACING THE HANDLE
3. To remove a handle, hold the file with one hand. Pull the file from the handle while striking the ferrule end of the handle against the edge of a bench.
Tap the handle on the bench top until the file is seated.
1.
CAUTION NEVER HAMMER A FILE INTO ITS HANDLE. 2. To install a new handle, insert tang end of file into handle socket exerting pressure with your hands.
28-6
TM 9-243
Chapter 29 GRINDERS AND SHARPENING STONES

The Types and Uses section provides you with a list of some of the types of grinders and sharpening stones. These pages should help you select the right sharpening instrument to do the job.
The Using section tells you how to use the sharpening instrument to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item TYPES AND USES . . . . . . . . . . . . . . Bench grinder . . . . . . . . . . . . . . . . . . . Valve grinder . . . . . . . . . . . . . . . . . . . Sharpening stones . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . Page 29-2 29-2 29-2 29-3 29-3 29-6
29-1
TM 9-243
TYPES AND USES

Grinders are mechanical devices which allow you to reshape, form, and sharpen metal cutting tools or other tools. A grinder consists of an abrasive wheel mounted on a rotatable shaft. The abrasive wheels are available in varying degrees of coarseness, depending upon type of metal to be ground. Sharpening stones may be either natural or artificial. Natural stones are of a finer grain than the artificial stones.
VALVE GRINDER
BENCH GRINDER
Bench grinders are used for reshaping and sharpening chisels, drills, hatchets, and other similar small hand tools. The bench grinder consists of a clamp (1), a rest (2), an abrasive wheel (3), a handcrank (4), and an encased gearing assembly (5). The clamp is used for fastening the grinder to a working surface. The rest supports tools which are being ground. It is adjustable and may be moved from side to side. The abrasive wheel may be changed depending upon the type of metal being ground. The valve grinder is a hand-operated special grinder. It is used for grinding the valve seating surfaces on combustion engines. It grinds with cutting blades on a rotating shaft instead of an abrasive wheel. It consists of an encased gear housing (1), a handcrank (2), interchangeable shafts (3), cutting blades (4), and a suction cup (5). The suction cup is used in place of a blade to grind non-slotted valves to fit seating surfaces.
29-2
TM 9-243

SHARPENING STONES
Sharpening stones usually have one coarse face and one fine face. This could combine the coarse artificial stone with the fine natural stone. The coarse edge is used to remove nicks and to reshape the tool being sharpened. The fine edge is used to complete the sharpening process and put a keen edge on the tool. Sharpening stones are available in various shapes and sizes, as shown.
USING A BENCH GRINDER
WARNING WEAR EYE PROTECTION AND WATCH THE FINGERS. HOLD TOOLS BEING SHAPED FIRMLY, SO THEY WILL NOT CATCH IN ABRASIVE WHEEL AND CAUSE INJURY.
1 Before using, inspect the grinder and abrasive

CAUTION Never use a cracked wheel. Before using a wheel, tap it lightly with a mallet. A ringing sound indicates that the wheel is satisfactory; a dull sound indicates that the wheel may be cracked. wheel, checking for cracks or breaks on exposed surfaces.
2 Unscrew the mounting clamp (1) to allow the grinder

to be positioned on the bench.
29-3
TM 9-243
USING A BENCH GRINDER - Continued

NOTE Since user must use both hands to hold tool to the wheel, another person is required to turn the handcrank in a counterclockwise direction.
Position grinder where it will be used and tighten the mounting clamp (1) to hold securely on the bench.
6 Rotate the handcrank and move the tool forward

until it makes contact with the wheel.
1 Loosen the wing nut (2) on the rest (3). Adjust the
rest (3). Tighten the wing nut (2).
2 Support the tool to be ground on the rest (3).
Move the tool back and forth across the abrasive wheel face to be sure of an evenly ground surface.
29-4
TM 9-243
USING A BENCH GRINDER - Continued
9 When the desired edge is obtained, you are 8 Stop grinding occasionally to check for the desired
edge. finished. Remove grinder from bench by loosening the clamp (1). Store grinder in its designated storage area.
USING A SHARPENING STONE

NOTE Unless stone is already oil-impregnated, apply a light coat of oil before and during use. WARNING KEEP YOUR FINGERS CLEAR OF THE HINGE AREA OF A POCKET KNIFE.
1 Hold the handle (1) of the blade to be sharpened in

one hand and extend the blade (2) across the stone.
2 Press down on the blade with the fingers of the other

hand.
With a circular motion, stroke the blade with the sharp edge trailing.
29-5
TM 9-243
USING A SHARPENING STONE - Continued
5 Repeat stroking action until the desired edge is 4

After several strokes, reverse the blade and stroke the other side in a similar manner. Use light, even pressure.
obtained. The wire edge left on blade by using a stone may be removed by stroking both sides on a soft wood block, canvas, or leather.
CARE OF BENCH GRINDERS

1. Wipe oil and grease from all outside surfaces before
and after each use.
2. Tighten all housing screws before and after each 3.

use. Before using, check to be sure that the abrasive wheel is not cracked or broken.
CARE OF SHARPENING STONES

1. 2. 3. 4.
Prevent glazing of stone by applying light oil while using. Wipe excess oil and grit from stone with a clean rag after each use. Clean stone with dry cleaning solvent when it becomes glazed or gummed up. Store in a clean dry place and/or wrap in clean cloth.
29-6
TM 9-243
Chapter 30 SCRAPERS
The Types and Uses section provides you with a list of some of the types of scrapers. These pages should help you select the right scraper to do the job.
The Using section tells you how to use the scraper to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . 30-2 Carbon scraper . . . . . . . . . . . . . . . . . . . . 30-2 Bearing scraper . . . . . . . . . . . . . . . . . . . . 30-2 Box scraper . . . . . . . . . . . . . . . . . . . . . . . . 30-2 Flat blade scraper . . . . . . . . . . . . . . . . . . 30-2 Triangular blade scraper . . . . . . . . . . . . 30-2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-3 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-3 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-3
30-1
TM 9-243
TYPES AND USES

Scrapers are made in different shapes for various types of work. Some scrapers are used for trueing metal, wood, and plastic surfaces which have been machined or filed. Other scrapers are made to remove paint, stencil markings, and other coatings from various surfaces.
BOX SCRAPER
CARBON SCRAPER
Box scrapers are most generally used to scrape stencil markings from wood surfaces. They are also used as wood floor scrapers. The box scraper has a 2-inch blade and a 9-inch handle hinged at the blade. The bottom of the scraper and the edge of the cutter are convex so that corners do not scratch up the work. The blade can be adjusted by loosening the thumbscrew and extending or withdrawing the blade in its holder.
A carbon scraper is used to clean carbon from, cylinder heads, pistons, and other metal surfaces. It is flexible and has an overall length of approximately 9 inches. The carbon scraper consists of ten round spring steel blades, and their flexibility is controlled by a sliding ferrule.
FLAT BLADE SCRAPER
BEARING SCRAPER
Flat blade scrapers are used for removing high spots from flat surfaces only.
TRIANGULAR BLADE SCRAPER
Bearing scrapers are used to scrape babbitt metal bearings. Bearing scrapers come with 1-1/2, 2, and 4-inch cutting edges. Triangular blade scrapers are used for removing high spots from flat or curved surfaces. They are available with either a 4 or 6-inch blade.
30-2
TM 9-243
SAFETY
1. 2. Keep work, scraper, and hands free from grease and oil when using a scraper. Keep scrapers sharp at all times, (except the carbon scrapers), since a dull scraper is more apt to slip and cause injury. 3. Use the scrapers only for their intended purposes. NOTE Carbon scraper blades are fairly dull to prevent scoring of a piston and/or cylinder wall.
USING A BEARING SCRAPER
1 Place the bearing to be scraped on a bench or other

suitable working surface.
2 Use both hands on the bearing scraper. One hand

should be at the end of the handle while the other hand steadies the tool.
4 Start at one top side of bearing cap. Work down, and

then up to the top of the other side. Do not scrape lengthwise.
3 Use the hand at the end of the handle to twist the

tool. Use very light pressure and remove a small amount of metal with the twisting stroke. If too much pressure is applied, the scraper will chatter and leave a rough, uneven surface.
5 Repeat procedure until the required amount of

material has been removed to fit the bearing onto the shaft.
CARE OF SCRAPERS
1. Keep scrapers sharp (except carbon scrapers) by sharpening or grinding. NOTE Carbon scraper blades are fairly dull to prevent scoring of a piston and/or cylinder wall. 2. 3. When a scraper is not in use, coat the blade with a film of light oil. Hang or store scrapers separately to protect the cutting edge. Do not throw scrapers in with other tools. This will damage the cutting edges. For long-term storage, coat all metal parts with rust-preventive compound and store in a dry place.
4.
30-3/(30-4 blank)
TM 9-243
Chapter 31 AWLS
The Types and Uses section provides you with a list of some of the types of awls. These pages should help you select the right awl to do the job.
The Using section tells you how to use the awl to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . Saddlers awl . . . . . . . . . . . . . . . . . . Scratch awl . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . .
31-2 31-2 31-2 31-2 31-2
31-1
TM 9-243
TYPES AND USES

SADDLERS AWL SCRATCH AWL
The saddlers sewing and stitching awl has a round wooden handle and interchangeable blades. The awl is used to punch holes in leather and as an aid during sewing. Cover points when not in use.
The scratch awl has a fixed tapered blade and a wooden handle. It is used to scribe marks or as a center punch on soft wood and plastics. Cover points when not in use.
USING A SCRATCH AWL
Place material to be scribed on a flat surface. Place a ruler or straight edge on guide marks. You will already have measured and marked where you want to scribe. WARNING AWLS ARE VERY SHARP AND MUST BE USED WITH EXTREME CAUTION
Hold straight edge firmly. Hold the awl like a pencil and scribe a line along the straight edge.
Remove the protective cover (1).
Replace protective cover (1).
CARE OF AWLS
1. 2. Keep points covered when not in use and stow awls in racks or in tool boxes. Lightly oil metal parts before storing.
31-2
TM 9-243
Chapter 32 BOLT AND CABLE CUTTERS

The Types and Uses section provides you with a list of some of the types of cutters. These pages should help you select the right cutter to do the job.
The Using section tells you how to use the cutter to perform the desired function. The Care procedures tell you how to care for the item.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . 32-2 Center cut cutter . . . . . . . . . . . . . . . . . . 32-2 Clipper cut cutter . . . . . . . . . . . . . . . . . . 32-2 Shear cut, flat bar, and strip cutter . . . . 32-2 Side nut splitter cutter . . . . . . . . . . . . . . 32-3 Angular cut cutter . . . . . . . . . . . . . . . . . 32-3 Shear cut cable cutter . . . . . . . . . . . . . . 32-3 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . 32-4 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-4 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-5
32-1
TM 9-243
TYPES AND USES

WARNING BOLT CUTTERS ARE CONSIDERED SECURITY ITEMS. ALWAYS SECURE, THESE TOOLS WHEN NOT IN USE. Bolt and cable cutters come with a variety of cutting edges which are designed for specific applications. They are shaped like giant shears with short blades and long handles. The handles are hinged at one end. The cutters are at the end of extensions, which are jointed in such a way that the inside joint is forced outwards when the handles are closed. This forces the cutting edges together with great force. Bolt cutters are made in lengths from 18 to 36 inches. The larger ones will cut mild steel bolts and rods up to 1/2-inch diameter.
CLIPPER CUT CUTTER
CENTER CUT CUTTER

The cutting edges of the clipper cut cutter are in line with the handles and beveled almost entirely from one side. These cutters allow very close cutting of projecting ends. The cutting capacities range from 1/4 inch to 9/16 inch for medium steel, and from 5/16 inch to 11/16 inch for soft steel. The handles range from 14-inch to 42-inch lengths.
SHEAR CUT, FLAT BAR, AND STRIP CUTTER
The center cut cutter is used for all general-purpose cutting. The cutting jaws are firmly fixed in line with the handles. The cutting edges are in the center of the jaw between equal levels. The longer the handle, the greater the cutting capacity. The cutting capacities range from 3/16 inch to 1/2 inch for medium steel, and from 5/16 inch to 11/16 inch for soft steel. The handles range from 14-inch to 42-inch lengths.
Shear cut, flat bar, and strip cutters are used to cut flat-soft, medium-hard bar, and strip stock. The cutting edges of the jaws pass each other in the manner of scissors, making a complete shear cut.
32-2
TM 9-243

SHEAR CUT, FLAT BAR, AND STRIP CUTTER (Cont)
The cutting capacities range from 7/8 x 5/32 inch to 1-1/2 x 9/32 inch for soft and medium steel, and from 3/4 x 1/8 to 1-7/16 x 1/4 inch for hard steel. The handles range from 14-inch to 36-inch lenghts.
ANGULAR CUT CUTTER
SIDE NUT SPLITTER CUTTER
Angular cut cutters have the cutting edges offset 30 degrees from the handles. This is so the user can keep the work in sight. It is used for close cutting of soft or medium-hard metals. Cutting capacities range from 1/4 inch to 1/2 inch for medium steel. The handles range from 14 inches to 36 inches in length.
SHEAR CUT CABLE CUTTER
The side nut splitter cutter has the edge of the cutting jaws in line with the handles. When adjusted properly, the cutting edges will remain separated after the nut is split. This tool is used to split nuts off bolts, with the tool head on to the bolt, without damaging the bolt. Cutting capacity is rated for a 3/8-inch bolt nut and is adjustable to 5/16-inch and 1/4-inch capacity. The handle is 24 inches long.
Shear cut cable cutters have curved interposing cutters. They are used to cut lead and rubber-covered cable, and communication cable. Cutting capacities for lead and rubber-covered cable is 1-3/8 inches for the 25-1/2-inch handle, and 2-1/4 inches for the 37-inch handle. The communication cable cutting capacity for the 25-1/2-inch handle is 500,000 circular mils, and 750,000 circular mils for the 37-inch handle.
32-3
TM 9-243
SAFETY
1. 2. 3. Wear safety glasses when cutting. When using bolt cutters, make sure your fingers are clear of the jaws and hinges. Take care that the bolt head or piece of rod cut off does not fly and injure you or someone else. When the cutters are brought together rapidly, sometimes a bolt-head or piece of rod being cut off will fly some distance. The harder the material, the more it will fly. 5. 4. If it is necessary to cut electrical cable or wire which is already installed, be sure that the power is disconnected before using the cable cutter on it. Bolt cutters are fairly heavy, so make sure that they are stored in a safe place where they will not fall and injure someone.
USING CENTER CUT CUTTERS

WARNING WHEN USING BOLT CUTTERS, MAKE SURE YOUR FINGERS ARE CLEAR OF THE JAWS AND HINGES. WEAR EYE PROTECTION. CAUTION Never attempt to cut spring wire or other tempered metal with bolt cutters. This will cause the jaws to be sprung or nicked.
Position the work as far back as possible into the jaws, to prevent damage to the jaws as well as to reduce the pressure required for cutting. CAUTION Use extreme care when using cutter to avoid catching any part of the body or clothes between handles as pressure is applied to them.
1 Clamp or steady the work if unattached before cutting, to prevent the cutters from slipping.
4 Stand at a right angle to the work being cut and

apply steady pressure to the handles until the work has been cut off. Do not pry or twist with the handles while cutting.
2 Dry hands and handles of cutter before using to

prevent slipping.
32-4
TM 9-243
CARE OF BOLT AND CABLE CUTTERS

1. 3. Replace worn cutters when necessary. Keep the adjusting screws just tight enough to ensure that the cutting edges meet along their entire length when the jaws are closed. Keep cutter jaws at right angles to the piece being cut. Do not twist or pry with the tool while cutting. 5. 6. Do not sharpen edges too sharp. Leave edge approximately 1/64-inch wide for longer jaw life. Before storing, wipe dirt and grease from the cutter and coat the metal parts lightly with oil to prevent rust. Store the cutter in a special compartment of the tool box or on a shelf where it cannot fall.
2. Keep moving parts well oiled.
4.
7.
32-5/(32-6 blank)
TM 9-243
Chapter 33 GLASS CUTTERS

The Types and Uses section provides you with a list of some of the types of cutters. These pages should help you select the right cutter to do the job.
The Using section tells you how to use the cutter to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . Wheel Type Glass Cutter . . . . . . . . . . . . Circle Glass Cutter . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33-2 33-2 33-2 33-2 33-4
33-1
TM 9-243
TYPES AND USES

WHEEL TYPE GLASS CUTTER CIRCLE GLASS CUTTER
The wheel glass cutter consists of a steel cutting wheel (1) notching teeth (2), and a holder (3). It is used for making straight cuts on glass.
The circle glass cutter has an adjustable arm (1), a cutting head (2), and a suction cup clamp assembly (3). The cutting head scores a mark on the sheet of glass. The suction cup assembly provides an anchor. The circle glass cutter is used to cut circles in glass. The adjustable arm can be moved in the suction cup assembly to allow circles from 2 to 24 inches in diameter.
USING A WHEEL-TYPE GLASS CUTTER

WARNING USE CARE WHEN HANDLING GLASS. WEAR GLOVES TO PROTECT YOUR HANDS.
1 2
Place padding (newspapers, a piece of carpet, or blanket) on a flat, level surface. Make sure the glass is clean. Apply alcohol (1) along the line to be cut. This prevents the cutting wheel from becoming gummed up while in use.
3 Place a straight edge (2) along line to be cut. A

wooden yardstick should be used when available, since wood will not slip easily on glass. The cutter will cut 1/16 inch from your mark, so adjust your guide before cutting.
33-2
TM 9-243
USING A WHEEL-TYPE GLASS CUTTER - Continued
4 Apply a drop of light machine oil (3) to the cutting

blade (4).
6 Start your cut at the far end of the pane of glass

drawing the cutter toward you. It is important that you maintain proper pressure throughout the cut. Correct pressure is indicated by a scratching sound. Too much pressure or a dull wheel will produce a crunching sound. Make a continuous mark from one edge to the other edge. NOTE Draw the cutter over the line only one time. If it is necessary to recut a groove, do not use a new cutter.
5 Hold down on the straight edge with one hand while

holding the cutter (5) in an upright position in the other hand. Your forefinger should extend along the holder with your fingertip near the wheel.
7 A proper cut is indicated by a slight crack in the

surface. It is best seen from the side opposite the mark.
33-3
TM 9-243
USING A WHEEL-TYPE GLASS CUTTER - Continued
9 Hold down on the section resting on the working 6 To part the glass, slide the pane of glass so the
scored groove (6) is about 1/8 inch beyond the table edge. surface. Grasp the section extending over the edge with your other hand. Apply a light downward pressure to part the glass.
10 Remaining chips may be removed by applying a

downward twisting motion using the notches of the cutter.
CARE OF CUTTERS
1. 2. Make sure cutting blades remain sharp. Sharpen dull blades with a file or oil stone. When not in use, apply a light film of oil on the cutting edges. 3. Store cutters in such a way as to prevent the blades accidentally making contact with personnel or other metal. For long periods of storage, coat entire cutter with rust-preventive compound and store in a dry place.
4.
33-4
TM 9-243
Chapter 34 KNIVES
The Types and Uses section provides you with a list of some of the types of knives. These pages should help you select the right knife to do the job.
The Using section tells you how to use the knife to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . Rubber cutting knives . . . . . . . . . . Saddlers knives . . . . . . . . . . . . . . . . Shop knife . . . . . . . . . . . . . . . . . . . . . Pocket knife . . . . . . . . . . . . . . . . . . . Draw knife . . . . . . . . . . . . . . . . . . . . . Putty knife . . . . . . . . . . . . . . . . . . . . . SAFETY . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . .
34-2 34-2 34-2 34-2 34-2 34-3 34-3 34-3 34-3 34-4
34-1
TM 9-243
TYPES AND USES

Most knives have cutting edges and are used to cut, pare, notch, and trim wood, leather, rubber, and other materials. However, putty knives are used to apply and spread putty when installing glass.
SHOP KNIFE
RUBBER CUTTlNG KNIVES
The shop knife is used to cut wallboard, paper, cardboard, linoleum, canvas, and upholstery materials. Most shop knives have an aluminum handle and have storage space for five interchangeable blades in the 5-inch handle.
POCKET KNIFE
Rubber cutting knives come in a variety of styles and shapes. Some taper to a blunt round point. Some have a short, wide blade. Others have a long, wide hollow ground blade. The handle is usually oval in shape.
SADDLERS KNIVES
Saddlers knives are used on leather and come in different shapes. One has a broad point on a 1-1/8-inch by 5-inch blade. One has a 5/8-inch by 3-7/8-inch square point blade. Another has a 5-inch rounded-end blade. Shoe knives are similar to saddlers knives, but usually they have a 3/4-inch by 3-1/4-inch blade.
Pocket knives are used for light cutting, sharpening pencils, cutting string, and whittling. They are not suitable for heavy work. There are many styles and shapes. Some are multipurpose and have an assortment of blades which are used for forcing holes, driving screws, and opening cans, as well as cutting. The blades are hinged and contained within the case when not in use and are spring loaded to keep them firmly in place when open or closed.
34-2
TM 9-243

DRAW KNIFE PUTTY KNIFE
A draw knife is a flat-edged tool used especially on round timber to rough-shape wood. It is used to smooth wood after chopping with a hatchet or axe. It consists of a single bevel blade and two round wooden handles, one at each end and at right angles to the blade. The handles may be adjustable or rigid.
A putty knife is used for applying putty to window sashes in setting panes of glass. The blade has a wide square point and is available in different lengths and widths.
SAFETY
1. 2. 3. Do not use knives which are larger than can be handled safely to cut work. Use knives only for the purpose for which they were designed. Do not carry open knives in your pocket. 6. 4. 5. Do not leave knives in such a position that they will cause injury to others. Carefully put knives in a sheath or container after use to protect the sharp cutting edges from contacting other hard objects. Always cut away from the body, except when using the draw knife.
USING A PUTTY KNIFE

1 2
Before applying new putty, -make sure that the frame (1) is clean and all the old putty has been removed. Roll new putty (2) into a rope and press it into the frame with your fingers.
34-3
TM 9-243
USING A PUTTY KNIFE - Continued

NOTE Occasionally dip the putty knife in water to aid in shaping the putty.
3 With the putty knife (3), shape the putty (2) into an
angle sloping from the glass down to the edge of the frame.
4 Miter the putty (2) at the corners as shown.
CARE OF KNIVES
1. 2. 3. Carefully put knives away after use. Protect the sharp cutting edges from contact with other hard objects. Use knives only for the purpose for which they are intended. 4. 5. Before storing, wipe all metal parts with an oily rag. For long-term storage, apply a thin film of rustpreventive compound on all metal parts and store in a dry place.
34-4
TM 9-243
Chapter 35 PIPE CUTTING AND THREADING TOOLS

The Types and Uses section provides you with a description of the pipe cutter and threading set. These pages should help you select the right cutting die to do the job.
The Using section tells you how to use the pipe cutter and threading set to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . Pipe threading set . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35-2 35-2 35-2 35-6
35-1
TM 9-243
TYPES AND USES

PIPE CUTTERS PIPE THREADING SET
There are two sizes of pipe cutters. One size can cut from 1/8 to 2 inches, while the other can cut from 2 to 4 inches. The pipe cutter has a cutting blade (1) and two pressure rollers (2) which are adjusted and tightened by turning the handle (3). Pipe cutters are used to cut steel, brass, copper, wrought iron, and lead pipe.
The pipe threading set contains an assortment of cutting dies (1) a handle or wrench (2) a collar (3), and locking screws (4). The cutting dies may range from 1/8-inch to 2 inches in diameter. The threading set is used to cut American Standard Pipe threads on steel, brass, copper, wrought iron, and lead pipe.
USING A PIPE CUTTER

WARNING PIPE OFTEN COMES WITH A PROTECTIVE CAP (1). LEAVE THIS CAP ON. IT KEEPS YOU FROM GETTING CUT ON SHARP PIPE ENDS.
Fasten pipe securely in a pipe vise (2). Be sure mark is clear so that it can be cut. Pipe must be supported on both ends to keep it from bending.
Measure from end of pipe and make a mark where you want to cut.
35-2
TM 9-243
USING A PIPE CUTTER - Continued
8 Remove the shoulder (the rough edge left by cutting) from the outside of the pipe with a file (5).
Remove the burr from the inside of the pipe with a pipe reamer (6). (See Chapter 39 for care and use of pipe reamers.)
Open the jaws of the pipe cutter enough to allow the pipe cutter to be placed around the pipe. Adjust so that the cutting blade (3) is on the line. contact with pipe.
4 Tighten the handle (4) until cutting blade makes 5 Then turn the handle (4) 1/4 of a turn more
clockwise.
6 7
Now turn the whole cutter one turn around the pipe (counterclockwise). Repeat steps 5 and 6 until the pipe is cut through. NOTE Be sure the cutter is at a right angle to the pipe as shown to keep the wheel on track.
10
Place protective cap (1) on cut pipe end and remove from vise. NOTE If the part of the pipe you cut off is going to be used, put in vise and repeat steps 8 and 9. If you are going to store the pipe, put the protective cover back on.
35-3
TM 9-243
USING A PIPE THREADING SET

WARNING PIPE ENDS ARE EXTREMELY SHARP. USE CARE WHEN HANDLING.
1 Clamp pipe securely in pipe vise (1) with end to be

threaded extending beyond the edge of the vise jaws as shown.
6 Secure in place with locking screws (4). 7 Set ratchet to turn in a counterclockwise direction
by pulling out ratchet control knob (5) and turning it 180 degrees. The ratchet permits cutting threads on pipes where it is not possible to turn the handle 360 degrees. It is set for clockwise or counterclockwise rotation by pulling out and turning the ratchet control knob (5) from one detent to the other.
2 Measure inside pipe diameter to determine the

proper die.
3 Inspect the die for nicks, and be sure that it is

sharp. Assemble die on ratchet die stock as shown in steps 4, 5, and 6. 4 Insert collar (2). 5 Insert cutting die (3) over top of collar (2).
8 Apply cutting oil (6) to die and to end of pipe (7) to

prevent overheating of dies and damaging of threaded surface.
35-4
Change 1
TM 9-243
USING A PIPE THREADING SET - Continued
9 Slide cutting die over end of pipe to be threaded

and apply light pressure with the heel of your hand.
12 After two more turns on the die, back off one turn
and apply a coat of cutting oil. NOTE If metal shavings become clogged in the die, remove the die and clean it with a piece of cloth.
13 Keep repeating step 11 until desired thread length

is obtained.
10 Start die with short strokes of the ratchet

handle (8). Be sure the die is going on the pipe squarely.
14 Reverse ratchet by pulling ratchet control knob (5) 11 After a full turn of the die, apply another coat of
cutting oil. from detent and turning it 180 degrees. Then back up the cutting die.
Change 1
35-5
TM 9-243
USING A PIPE THREADING SET - Continued
15 Wipe excess oil and metal shavings from die and

ratchet handle.
17 Wipe excess oil and shavings from threaded end

of pipe (7).
16
Disassemble the die from the ratchet handle as shown, by removing locking screws (9). Remove die and collar from ratchet head.
18 Place cap, if available, over threads and remove

the pipe from the vise.
CARE OF PIPE CUTTERS AND THREADING SETS

PIPE CUTTERS THREADING SETS
1. 2.
Clean and lightly oil the cutter wheel (1) roller guide (2) and adjusting screw (3). Store on a rack or in a box which protects the cutting wheel.
1. 2.
Wipe off excess cutting oil and clean metal shavings from the cutting die edges and collar. Store in a case or box which will protect the cutting dies.
35-6
TM 9-243
Chapter 36 TUBE CUTTING AND FLARING TOOLS

The Types and Uses section provides you with a description of the tube cutting and flaring tool. These pages should help you select the right flaring combination to do the job.
The Using section tells you how to use the tube cutting and flaring tools to perform the desired function. The Care procedures tell you how to care for the items.
INDEX Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . 36-2 Tube cutters . . . . . . . . . . . . . . . . . . . . . . . 36-2 Flaring tool . . . . . . . . . . . . . . . . . . . . . . . . 36-2 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-2 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36-4
36-1
TM 9-243
TYPES AND USES

TUBE CUTTERS FLARING TOOL
Tube cutters have a cutting blade (1), guide rollers (2), and an adjusting screw (3). Some cutters have a reaming blade attached to the frame of the cutter. Tube cutters can cut from 1/8 inch through 2-5/8 inches tubing. They can cut copper, aluminum, or brass tubing.
Flaring tools are of two basic types, single and double. They are used to put flares in soft tubing. The single flaring tool consists of a split die block, a locking clamp with compressor screw and a cone which forms a 45 degree flare on the end of the tube. The screw has a T-handle. The die block is constructed to be used on the following outside diameter tubing: 1/8, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, 5/8, and 3/4 inch. The double flaring tool consists of a split die block, a locking clamp with compressor screw, adapters for turning tube edge, and a cone which forms a 45 degree flare on the end of the tube. The screw has a T-handle.
USING A FLARING TOOL
Loosen die block clamp screws (1), and open die block clamp (2).
Insert tubing to be flared (3) into die block clamp.
36-2
TM 9-243
USING A FLARING TOOL - Continued
Hold tubing so there is about 1/8 inch extending above die block clamp, and tighten die block clamp screws. NOTE Do not over-tighten cutter as tubing may kink and flatten.
Tighten feed screw (6) forcing the tip (5) into the tubing and forcing the tubing into the chamber of the die block clamp.
Slide yoke (4) over die block clamp, and align the tip (5) over the end of tubing.
6 When desired flare is reached, unscrew feed screw,

and remove yoke from die block clamp.
36-3
TM 9-243
USING A FLARING TOOL - Continued
7 8 9
Unscrew die block clamp screws (1) and open die block clamp (2), releasing tubing (3). Inspect flange (7) in tubing for cracks or breaks. If a crack or break is detected, the tubing will have to be cut and reflanged.
CARE OF TUBE CUTTERS AND FLARING TOOLS.

TUBE CUTTERS FLARING TOOL
Keep cutting wheel clean and lightly oiled. If a reaming device is mounted on- the body of the cutter, keep it retracted when not in use. Store tube cutters on a rack or in a box.
Keep surfaces clean and lightly oiled. Close single flaring tools and tighten cone into block for storing. Keep double flaring tools in the case when not in use.
36-4
TM 9-243
Chapter 37 SHEARS AND NIPPERS

The Types and Uses section provides you with a list of some of the types of shears and nippers. These pages should help you select the right tool to do the job.
The Using section tells you how to use the shears and nippers to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . 37-2 Hand shears . . . . . . . . . . . . . . . . . . . . . . 37-2 Tinners bench shears . . . . . . . . . . . . 37-2 Metal shearing machine . . . . . . . . . . . . 37-2 Nippers . . . . . . . . . . . . . . . . . . . . . . . . . . 37-2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . 37-3 USING . . . . . . . . . . . . . . . . . . . ........ 37-3 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . 37-4
37-1
TM 9-243
TYPES AND USES

Shears are used for cutting sheet metal and steel of various thicknesses and shapes. Shears come in a variety of styles and sizes. that the operator will have a free hand to guide the work. The bench shear makes a 6-inch cut and is approximately 36 inches long.
METAL SHEARING MACHINE
HAND SHEARS
Hand shears are made with straight or curved cutting blades. Shears are made for right-handed operators so the cutline is always in full view for accurate cutting.
Straight-bladed shears are used to cut straight lines or to cut curves in locations that are easily reached.
The metal shearing machine is foot-operated and is used to cut original sheets into smaller, usable size stock. The shear blade is 36 inches long and will cut all sheet metal up to and including 1/16 inch of mild steel or 1/8 inch of iron.
NIPPERS
Shears with curved blades such as the hawk bill and the curved blade hand shears are made especially for cutting short straight lines or curves. They are also used for cutting out small intricate designs in locations where it is necessary to keep the handles and handle-operating hand away from the metal stock.
TINNERS BENCH SHEARS

Nippers are used to cut protruding metal flush with a surface. They are also used to cut wire, bolts, nails, and light metal bars to specified dimensions. Nippers come in a variety of styles and sizes.
The tinners bench shear is largerthan a hand shear and is used for cutting heavy sheet metal. The lower handle has a hook which can be placed in a hole in the bench so
37-2
TM 9-243

CUTTING NIPPERS
Some nippers have adjusting screw stops in the handle and adjustable jaws. Others have detachable jaws with compound leverage and come with three extra pairs of jaws. Cutting nippers range in size from 5-1/2 to 15 incheslong and up to 1-3/4 inches in jaw widths.
Cutting nippers are available with integral or detachable cutters. They are used to cut wire, light metal bars, bolts, nails, and to cut protruding metal flush with a surface.
SAFETY
1. Keep fingers, hands, and other parts of the body clear of the cutting edges of bench shears, the shearing machine, hand shears, and nippers. Do not carry shears or nippers in your pocket. 3. 4. Always steady the work that is to be cut. After use, be sure to hang the tools or store them in their proper place.
2.
USING CUTTING NIPPERS
WARNING
WEAR EYE PROTECTION AND WATCH THE FINGERS.
WIRE CUTTING
2 Take the nippers (3) in the right hand and place the
cutting edge on the mark.
NOTE Left-handed people will reverse this procedure.
3 1
Place the wire (1) on the table. Measure the section to be cut off. Mark it with pencil, chalk, soapstone or other suitable marking piece (2).
Squeeze the handles together slowly, exerting enough pressure to cut the wire. Repeat procedure for as many pieces of wire as need to be cut.
37-3
TM 9-243
USING CUTTING NIPPERS - Continued

FLUSH CUTTlNG 1 Place the cutting edge (1) of the nippers over the
nail, wire, rivet, or bolt (2) that is to be cut flush with. the surface.
2 Squeeze the handles (3) together slowly, exerting

enough pressure to cut the materials.
3 File cut edge smooth to prevent injury.
CARE OF SHEARS AND NIPPERS

1. 2. 3. Keep tools clean at all times. Lubricate the pivot screw or bolt with a drop of light oil. Remove rust with a fine aluminum-oxide abrasive cloth. Apply a thin film of oil on tools to prevent rust, and hang tools on hooks or place them on a shelf when not in use. Do not throw cutting tools together in a box where the cutting edges may be damaged. Do not use the shearing machine table as a storage place for other tools and work. Do not attempt to cut material heavier than the tools or machines are designed to handle. Do not use shears or nippers as hammers or pry bars, as they are easily damaged. 9.
8.
Dull shears can usually be sharpened on an oilstone or with a file. CAUTION Do not grind shears if sharpening is all that is necessary. Most shears become useless after two or three grindings. Grind the shears and nippers only if the cutting edges become nicked, damaged, or distorted from improper sharpening or prolonged use. For long-term storage, coat tools with a rustpreventive compound and store in a dry place where the cutting edges will not come in contact with other metal objects.
4. 5. 6. 7.
10.
37-4
TM 9-243
Chapter 38 TAPS AND DIES

The Types and Uses section provides you with a list of some of the types of taps and dies. These pages should help you select the right taps and dies to do the job. The Using section tells you how to use taps and dies to perform the desired functions. The Care procedures tell you how to care for the item.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . 38-2 Taper hand tap . . . . . . . . . . . . . . . . . . . . . 38-2 Bottoming hand tap . . . . . . . . . . . . . . . . . . 38-2 Plug/Pipe hand tap . . . . . . . . . . . . . . . . . 38-2 Boiler hand taps . . . . . . . . . . . . . . . . . . . . 38-2 Staybolt taps . . . . . . . . . . . . . . . . . . . . . . . 38-3 Mud hand tap . . . . . . . . . . . . . . . . . . . . . . 38-3 DIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-3 Rethreading die . . . . . . . . . . . . . . . . . . . . . 38-3 Two-piece collet die . . . . . . . . . . . . . . . . 38-3 Round split adjustable die . . . . . . . . . . . . 38-4 Thread cutter set . . . . . . . . . . . . . . . . . . . . 38-4 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-4 Hand tap . . . . . . . . . . . . . . . . . . . . . . . . . . 38-4 Die and diestock . . . . . . . . . . . . . . . . . . . . 38-5 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38-7
Change 1
38-1
TM 9-243
TYPES AND USES

Taps and dies are used to cut threads in metal, plastics or hard rubber. The taps are used for cutting internal threads, and the dies are used to cut external threads.
BOTTOMING HAND TAP
TAPS
The bottoming hand tap has a chamfer length equal to one to one and one-half threads. This tap is used for threading the bottom of a blind hole only after the taper and plug taps have been used. This tap is also used when tapping hard materials.
PLUG/PIPE HAND TAP

Taps are made of hardened steel and have the following parts: a square end (1) a round shank (2) a body (threaded) section (3) and a chamfer (4). The square end is used to turn the tap with either a straight or T-handled tap wrench. The shank is a smooth, rounded section which is immediately behind the threaded section. The body (threaded) section contains four flutes which have threads cut into their upper edges. They have a hollow section near the center to permit metal shavings to fall away from the cutting edges. The chamfer is the non-threaded end of the tap. It allows the tap to be positioned squarely in the metal to be threaded without engaging the threads of the tap.
The pipe tap has a tapered diameterwhich increases at a rate of 3/4 inch per foot. All the threads on the pipe tap are designed to cut pipe. The pipe tap is used for cutting pipe fittings and in other places where extremely tight fits are required.
TAPER (STARTING) HAND TAP
BOILER HAND TAPS

There are two types of boiler taps, straight and tapered.
Straight boiler taps range in size from 1/2 inch to 1-1/2 inches in diameter and have a chamfer for starting the tap. The taper (starting) hand tap has a chamfer (nonthreaded) length equal to eight to ten threads. The taper hand tap is used to start tapping operations.
Tapered boiler taps have tapered diameters which increase at a rate of 3/4 inch per foot.
38-2
Change 1
TM 9-243

STAYBOLT TAPS MUD HAND TAPS (WASHOUT TAP)
Staybolt taps are used in boiler, locomotive, and railroad shops for tapping holes in the outer and inner plates or shells of boilers. The staybolt tap has two separate threaded areas. The first is for cutting threads and the second is for guiding the tap into another piece of metal for threading by the cutting threads. The spindle-type staybolt has an adjustable spindle which changes the distance between the cutting threads and the guide threads.
The mud or washout tap has six flutes, tapers 1-1/4 inch per foot, and has 12 threads per inch. It is used for cutting American National or V-form threadsin mud plug drain holes.
DIES
RETHREADING DIE TWO-PIECE COLLET DIE
Rethreading dies are used to restore bruised (rounded) or rusty threads on screws and bolts. The rethreading die is hexagonal in shape and may be turned with a socket, box, open-end, or any other wrench that will fit. They are available in American Coarse and Fine Threads. Rethreading dies are available in a variety of sizes and are usually assembled in sets with a case.
The two-piece collet die consists of the two die sections, the collet cap, and collet guide. The die sections are placed inside the cap and held in place by the guide. Adjustment of the die is done by turning setscrews on either end of the internal slot. They are used to cut American Standard Coarse and Fine Threads and are available in assorted sizes.
38-3
TM 9-243
DIES - Continued
ROUND SPLIT ADJUSTABLE DIE THREAD CUTTER SET
The round split adjustable die (1), or button die, may be adjusted through the screws on the holder. Adjustment on the open type is done by turning the three screws on the holder. One expands the die while the other two compress the die. Adjustment of the screw type (2) is done by turning a fine-pitch screw that either forces the die jaws apart or allows them to spring together. The round split adjustable dies are used to cut American Standard Coarse and Fine Threads. A die holder or handle is needed for proper operation of round split adjustable dies.
The thread cutter set is made up of a combination of taps, dies, diestocks, tap wrenches, guides, and screwdrivers and wrenches for making adjustments. Thread cutter sets are used for cutting internal and external threads.
USING A HAND TAP

The following procedures may also be followed when using a taper tap or a bottoming hand tap.
Select tap (3) and secure in tap wrench (4).
Clamp a steel plate (1) securely in a vise (2). Drill and ream a hole of desired size.
3 Apply cutting oil to the tap and the hole.
38-4
TM 9-243
USING A HAND TAP - Continued
6 Replace the tap wrench and continue tapping operation. It is not necessary to apply pressure, as the threads will be pulled through at all times.
4 Place point of the tap in hole (5) and rotate

clockwise for right-hand threads or rotate lefthanded tap counterclockwise for left-hand threads.
7 Remove tap by turning in the opposite direction.

Wipe excess oil and metal shavings from metal plate. Check newly-cut threads with screw pitch gage before inserting screw or stud.
5 Remove tap wrench and, using a square (6), check

tap for squareness. Check at least two different positions on the tap.
USING A DIE AND DIESTOCK

NOTE Work to be threaded must be clean and free of burrs.
Secure the work (1) firmly in a vise (2).
38-5
TM 9-243
USING A DIE AND DIESTOCK - Continued

5 Tighten thumbscrews (6) securing diestock to 6
work. Rotate the diestock (4) clockwise, slowly but firmly, until the die takes hold.
CAUTION After assembling die to diestock, make sure setscrew is tight. Die could fall out of diestock causing damage to die.
Use square (8) to check squareness after several threads have been cut.
2 Assemble die (3) and diestock (4). Tighten

setscrew (5). Loosen the two thumbscrews (6) to adjust diestock (4).
8 Turn the diestock (4) one turn forward and

one-quarter turn backward. Repeat this procedure until desired thread length has been cut.
3 Apply cutting oil (7) to the die and to the work.
9 Carefully back the diestock (4) off the threads by 4 Position the diestock (4) over the work (1).
turning in a counterclockwise direction.
38-6
TM 9-243
USING A DIE AND DIESTOCK - Continued
Clean threads (9) with a clean rag and check with a screw pitch gage (10) before using.
11
Disassemble die (3) and diestock (4) by loosening setscrew (5). Wipe clean with a rag.
CARE OF TAPS
1. 2. 3. 4. Do not attempt to sharpen taps. Keep cutting edges lightly oiled. Wipe excess oil and metal shavings from tap and tapwrench. Store them in a case or wrap individually in cloths to protect cutting surfaces.
CARE OF DIES
1. 2. 3. Do not attempt to sharpen dies. Keep cutting surfaces clean and lightly lubricated. Store in a case or wrap individually in cloths where they will not come in contact with other tools.
38-7/(38-8 blank)
TM 9-243
Chapter 39 REAMERS
The Types and Uses section provides you with a list of some of the types of reamers. These pages should help you select the right reamer to do the job.
The Using section tells you how to use the reamer to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . Solid straight-hole reamer . . . . . . . . . . . . Solid taper-pin reamer . . . . . . . . . . . . . . . Expansion reamer . . . . . . . . . . . . . . . . . . Adjustable blade reamer . . . . . . . . . . . . . Pipe reamer . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39-2 39-2 39-2 39-2 39-3 39-3 39-3 39-4
39-1
TM 9-243
TYPES AND USES

SOLID TAPER-PIN REAMER
Reamers are used to enlarge and true a hole. They are also used to remove burrs from the inside diameters of pipes and drilled holes. The reamer consists of three parts, the body (1), the shank (2), and the blades (3). The shank has a square tang to allow the reamer to be held with a wrench for turning.
SOLID STRAIGHT-HOLE REAMER
Solid taper-pin reamers are used to finish tapered holes for the insertion of tapered pins or other tapered parts. They are made with a standard taper of 1/4 inch per foot. Solid taper-pin reamers come with straight (1) or spiral flutes (2). Sizes range from 5/0 to 14, with the diameter at the large end ranging from 0.0984 to 1.5412 inches. They also come in sets of 10, sizes 3/0 to 7, and a set of 11, sizes 0 to 10. They are also included in mixed sets of straight and taper-pin reamers.
EXPANSION REAMER
A solid straight-hole reamer is made of one solid piece of high-speed steel having a straight shank and straight (1) or spiral flutes (2). The cutting edges, or lands, between the flutes are usually evenly spaced. Some have irregularly spaced lands to prevent the tool from chattering. They come in sizes from 1/16 inch to include 3-inch diameters. Reamers are also available in sets containing 25 reamers in 1/64-inch increments from 1/8 inch to 1/2 inch. The sets may be mixed to include straight and taper pin reamers. Each reamer size is stamped on the shank of the tool. Solid straight-hole reamers are used for most work since they are the most accurate and the most rugged of the straight-hole reamers.
Expansion reamers are adjustable, and their sizes may be changed by 1/8 inch for a 1 -inch reamer and 5/16 inch for a 2-inch reamer. The expansion reamer is made of carbon steel and has longitudinal cuts in some of its flutes. It is hollowed out and threaded to receive a tapered screw plug. The diameter of the reamer is changed by screwing in or backing out the screw plug. The standard sizes range from 1/4 inch to 1 inch, by 32nds. A 1/4-inch expansion reamer will enlarge the hole to a 9/32-inch hole, etc. It is used for general purposes and is considered the most practical reamer.
39-2
TM 9-243

ADJUSTABLE-BLADE REAMER PIPE REAMER
The blades of an adjustable reamer are separate from the body and are fitted into grooves in the threaded shank of the tool. Adjusting nuts located below and above the blades control the diameter of the reamer. The reamers come with straight (1) or spiral flutes (2), with or without a floating pilot on solid mandrels, and in several sizes. Adjustable reamers are also available in sets. They are used to enlarge drilled holes to an exact true size using a series of small cuts rather than one deep cut.
Pipe reamers are made of carbon steel. They are tapered with straight or spiral flutes. They come in three sizes, 1/8-inch to l-inch pipe capacity, 1/4-inch to 1-1/4-inch pipe capacity, and 1/4-inch to 2-inch pipe capacity. Most pipe reamers are designed to receive a T-handle (1). Others (2) have a tapered square shank for use with a brace, or a round shank for use with a hand drill. They are used to remove burrs from the inside diameters of pipe and drilled holes.
USING A SOLID STRAIGHT-HOLE REAMER

1 Secure the work in a vise so that the hole to be
reamed is perpendicular to the top of the vise jaws.
2 Using a tap wrench (1), tighten the handle to the

square end of the reamer shank (2). CAUTION Do not turn the wrench counterclockwise at any time. To do so will cause the reamer to become dull.
3 Position the reamer (3) at the top of the hole. Turn

the wrench clockwise very slowly until the reamer is centered in the hole. Straight-hole reamers (4) have a slight taper at the end so they will fit into the hole easily.
39-3
TM 9-243
USING A SOLID STRAIGHT - HOLE REAMER - Continued

4 Turn the wrench clockwise with a steady, firm pressure until the reamer has been turned in the hole. When reaming steel, use cutting oil or machine oil to lubricate the tool. When reaming soft iron, do not lubricate the tool. Turning the wrench too fast or too slowly will cause the reamer to chatter, producing an unevenly reamed hole.
5 Remove the reamer from the hole by turning the

wrench clockwise and raising the reamer at the same time.
CARE OF REAMERS
1. 2. Keep reamers absolutely clean to do accurate work. Do not use the reamer to remove more than 0.002 to 0.003 inches of metal. If the hole is too small, enlarge it with a drill before reaming it. If the proper pressure is applied in use and the reamer chatters, replace it to insure accurate work. If the reamer edges are only slightly dulled, honing the edges on an oilstone may restore the sharpness. On an adjustable reamer, the blades may be replaced. 5. To prevent chipping or dulling the reamer when you are reaming a hole, turn the reamer in the cutting direction only. To prevent damage to the reamer for short-term storage, wrap it in an oily cloth and keep it in a box. For long-term storage, clean reamer thoroughly and coat with rust-preventive compound. Wrap each reamer separately in oiled cloth and store in a dry, safe place.
6. 7.
3. 4
39-4
TM 9-243
Chapter 40 BENDERS
The Types and Uses section provides you with a list of some of the types of benders. These pages should help you select the right bender to do the job.
The Using section tells you how to use the bender to perform the desired function. The Care procedures tell you how to care for the items. INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . 40-2 Spring tube benders . . . . . . . . . . . . . . . . . 40-2 Hand tube bender . . . . . . . . . . . . . . . . . . .40-2 Electrical conduit hand bender . . . . . . . .40-2 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 . 0-3 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40-4
40-1
TM 9-243
TYPES AND USES

SPRING TUBE BENDERS ELECTRICAL CONDUIT HAND BENDER
There are two types of spring tube benders, external and internal. The spring tube bender permits the bending of small diameter tubing by hand without collapsing the tubing. External benders are used to bend straight sections of tubing which have at least one end which has not been flared. They are available in 1/4, 5/16, 3/8, 7/16, 1/2, and 5/8-inch diameters. Internal benders are used for bending straight sections of tubing which have both ends flared. They are available in 3/8, 1/2, and 5/8-inch outside diameters. The electrical conduit hand bender has precise grooves to insure a smooth bend. It has a concave base (1), a foot rest (2) and a retaining hook (3) to keep conduit from slipping as it is being bent. The bender has a threaded opening for attaching a threaded piece of pipe to be used as a handle. Electrical conduit hand benders are available in 1/2, 3/4, 1, 1-1/4, 1-1/2, and 2 inches in diameter. They are used to bend thin wall and rigid conduit to allow for flat installation on inside building walls.
HAND TUBE BENDER
The hand tube bender consists of the following components: a handle (1) a radius block (mandrel) (2), a clip (3) and a slide bar (4). The radius block is graduated from 0 to 180 degrees, and the slide bar has a scribe mark which indicates the degree of bend. These benders are available in 3/16, 1/4, 5/16, 3/8, and 1/2-inch sizes. The hand tube bender is used to bend copper, brass, or aluminum tubing to specific angles.
40-2
TM 9-243
USING A TUBING BENDER
1 2
Raise slide bar (1) and insert tubing (2) to be bent. Raise locking clip (3) and lock tubing in place.
5 Stop bending the tubing when the zero mark on the

slide bar matches the desired angle (6) on the block.
Lower slide bar. The zero mark (4) on the slide bar should match up with the zero mark on the block (5).
Raise the slide bar (1), lift up the locking clip (3) and remove the bent tube (2).
Apply downward pressure on the slide bar.
49-3
TM 9-243
USING AN ELECTRICAL CONDUIT HAND BENDER

CAUTION Do not jerk the handle, as this will create internal cracks and ridges inside the conduit which will cut the wires.
1 Install handle (1) on bender (2). A section of

threaded pipe may be used as a handle.
4 Place one foot on the foot rest (5) and push down
with your foot while pulling back on the handle. Apply steady pressure throughout the entire bending process.
2 Tip the bender forward and slide the section of

conduit (3) to be bent through the retaining hook (4).
3 Place mark where bend is to start opposite the

arrow on the front end of the bender.
5 When desired bend has been obtained, release the

pressure on the conduit by returning the handle to an upright position and slide the conduit out of the bender.
CARE OF BENDERS
1. Clean all grease and oil from gripping surfaces with a rag. 2. 3. Apply a light coat of oil to non-gripping surfaces. Store in a safe, dry place.
40-4
TM 9-243
Chapter 41 PULLERS
The Types and Uses section provides you with a list of some of the types of pullers. These pages should help you select the right puller to do the job.
The Using section tells you how to use the puller to perform the desired function. The Care procedures tell you how to care for the items.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . 41-2 Universal gear puller . . . . . . . . . . . . . . . . 41-2 Gear and bearing puller . . . . . . . . . . . . . 41-2 Universal bearing and bushing puller . . . 41-2 Electrical unit bearing puller . . . . . . . . . . 41-2 Battery terminal and small gear puller . . . 41-2 Steering gear arm puller . . . . . . . . . . . . . . 41-2 Push and pull puller set . . . . . . . . . . . . . 41-3 Steering wheel puller set . . . . . . . . . . . . 41-3 Wheel puller set . . . . . . . . . . . . . . . . . . . . 41-3 Cylinder sleeve puller . . . . . . . . . . . . . . . . 41-3 Slide hammer puller . . . . . . . . . . . . . . . . 41-4 Cotter pin puller . . . . . . . . . . . . . . . . . . . . 41-4 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-4 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-5
41-1
TM 9-243
TYPES AND USES

UNIVERSAL GEAR PULLER ELECTRICAL UNIT BEARING PULLER
The universal gear puller is usually of yoke and screw construction with two jaws. The jaws have a capacity from 0 to 14 inches in diameter. The universal gear puller is used for pulling gears, pulleys, and wheels.
GEAR AND BEARING PULLER
The electrical unit bearing puller is used to pull bearings from shafts of electrical units. It is supplied with plates to fit a variety of unit constructions and to fit behind the particular shaft bearings to be pulled.
BATTERY TERMINAL AND SMALL GEAR PULLER
The gear and bearing puller is used to pull gears, bearings, pinions, sheaves, pulleys, and wheels. It is a screw-type puller with two jaws. The grip tightens as pull is increased. The gear and bearing puller has a maximum spread of 5-1/2 inches.
The battery terminal and small gear puller is a screwtype puller for use in close quarters. In addition to pulling battery terminals, it is used to pull small gears and bearings.
UNIVERSAL BEARING AND BUSHING PULLER
STEERING GEAR ARM PULLER
The universal bearing and bushing puller has interchangeable jaws. It provides a pulling capacity of up to 1-1/4 inches. The larger jaws are used for removing bronze or oilite bushings without crumbling them. The smaller jaws are used to pull clutch pilot bearings.
The steering gear arm puller is used for pulling steering gear arms. It also can be used for a wide variety of other pulling jobs. The clamp locks the puller on the arm, leaving both hands free for pulling.
41-2
TM 9-243

PUSH AND PULL PULLER SET WHEEL PULLER SET
The push and pull puller set is used in conjunction with a variety of attachments and adapters. The push and pull puller consists of a 13-1/2-inch steel bar which is slotted to receive two 9-1/2-inch legs. A pressure screw in the center of the bar is 13 inches long. It has a diameter of one inch, and it is threaded. This puller is universal and versatile. With the use of the bearing pulling attachment, bearing cup pulling attachment, sheave puller attachment, threaded adapters, step plate adapters, additional legs, and many other special adapters, this puller is capable of removing or replacing bearings, gears, pinions, pulleys, wheels, and bushings. The push and pull puller set has many other uses.
The universal wheel puller set consists of a body and drive assembly that receives three long jaws, three short jaws, or a special grooved hub set. The interchangeable jaws pivot and swing to any desired bolt circle. Tapered, right and left hand threaded stud nuts complete the set; all of which are carried in a metal case. The wheel puller set is capable of pulling any demountable wheel hub for any passenger car, and most lightweight trucks.
CYLINDER SLEEVE PULLER
STEERING WHEEL PULLER SET
The steering wheel puller consists of all the units necessary for removal of steering wheels from early models of cars and trucks up to the present models.
The universal cylinder sleeve puller is used to pull cylinder sleeves from engine blocks. It is adjustable to provide clearance regardless of the position of the cylinder studs and to simplify centering the tool over the bore. This puller is used in conjunction with four adapter plates supplied with the puller. The combination is capable of pulling cylinder sleeves 4-1/4, 4-1/2, 4-3/4, and 5-3/4 inches in diameter.
41-3
TM 9-243

SLIDE HAMMER PULLER COTTER PIN PULLER
The slide hammer puller set is a universal-type puller equipped with a two and three-way yoke, three medium jaws for outside pulls and two small jaws for inside pulling. The small jaws can be inserted through a 1/2-inch opening. The capacity of the medium jaws is 6-1/4 inches. The slide hammer puller is also equipped with a locking feature which holds the jaws open or locks them on the work.
A cotter pin puller is an S-shaped tool used to install or to remove cotter pins. One end is used to insert through the cotter pins for extracting. The other end is used for spreading the cotter pin. The shank is beveled square for easy handling and for a firm grip. This type is seven inches long.
USING A GEAR AND BEARING PULLER
1 Check all gripping edges and threads of a puller for

damage before using it. 2 Place the puller (1) firmly in position and secure it.
3 Use the proper size wrench for turning the pressure

screw or nut (2) to avoid rounding the corners of the nut or of the screw head.
4 Turn the pressure screw or nut slowly in a clockwise

direction until the gear bearing is removed. WARNING TURN THE PRESSURE SCREW OR NUT SLOWLY TO PREVENT INJURY AS THE GEAR BEARING IS RELEASED.
41-4
TM 9-243
USING A SLIDE HAMMER PULLER SET

1 Check to make sure that you have all parts before
starting the process. Make sure the threads are clean and will move freely.
2 Lock the jaws (1) on the gear with the locking feature and slide the hammer handle (2) up the shaft in the direction of the pull. WARNING DO NOT SLIDE THE HANDLE TOO RAPIDLY. THE GEAR MAY FLY OFF AND CAUSE INJURY.
3 Slide the handle in a series of slides until the gear is

loose or comes off.
CARE OF PULLERS
1 2 3 4
Keep pullers clean at all times. Do not grease or oil the gripping edges. This will cause the tool to slip. Clean all the tools after use and store so the threads will not become damaged. Make certain that attachments and adapters are stored with the basic puller and that they do not become separated.
5 Oil pullers after use and wipe clean before using

again. 6 When storing for long periods, apply a coat of rustpreventive compound on the tools and store them in a dry place.
41-5/(41-6 blank)
TM 9-243
Chapter 42 BARS
The Types and Uses section provides you with a list of some of the types of bars. These pages should help you select the right bar to do the job.
The Using section tells you how to use the bar to perform the desired function. The Care procedures tell you how to care for the item.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . Wrecking bar . . . . . . . . . . . . . . . . . . . . Crowbar . . . . . . . . . . . . . . . . . . . . . . . . . Pinch bar . . . . . . . . . . . . . . . . . . . . . . . Combination bar . . . . . . . . . . . . . . . . . . SAFETY . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . .
42-2 42-2 42-2 42-2 42-2 42-2 42-3 42-3
42-1
TM 9-243
TYPES AND USES

Bars are steel tools used to lift and move heavy objects and to pry where leverage is needed. They can also be used to remove nails and spikes, and to loosen hard soil for digging. The most commonly used types of bars are the wrecking bar, crowbar, pinch bar, and combination pry bar. These bars range from 12 inches to 72 inches in length, depending upon their design and the purpose for which they are used. should be used in a position where the weight of the users body is exerted downward on the long section of the lever. When possible use a block or other object as a fulcrum behind the bar, near the spot where the bars point is wedged under the object to be moved.
PINCH BAR
WRECKING BAR
The wrecking bar is used to pull large nails or spikes, to open heavy crates, and to do wrecking work.
The pinch bar is used for light ripping and prying jobs.
COMBINATION BAR
CROWBAR
The crowbar is used for heavy prying and for moving heavy timbers and other large objects short distances. It can also be used for loosening rock formations, as a lever for moving rails, and for breaking up hard earth when digging. In moving heavy objects or prying, it
The combination pry bar is an all-purpose combination pry and scrape bar for rugged heavy-duty service. It is used to pry, pull, cut, scrape, lift, and pound nails. The slim tapered blades are easily inserted for prying and lifting. It also has beveled nail slots.
SAFETY
1. Wrecking bars are exceptionally heavy, and care must be taken to keep them from falling and striking someone. When using bars for prying, make sure the bar does 3. not slip and cause personal injury. Do not use bars for extra heavy work, since they will bend and may cause injury.
2.
42-2
TM 9-243
USING THE COMBINATION BAR

WARNING USE CARE IN USING THE COMBINATION BAR TO AVOID SLIPPAGE AND PERSONAL INJURY.
1 Insert the long tapered blade (1) between boards (2)

to be removed or ripped. Then exert leverage on the short hooked blade (3) of the bar to pry the boards loose.
3 To remove nails, use the short hooked blade (3) nail

slot to remove a nail that is almost completely driven home. Pull the nail approximately half-way out. Then switch to the long tapered blade (1) nail slot to completely remove the nail.
2 Insert the short hooked blade (3) between the

boards if greater leverage is required.
CARE OF BARS
CAUTION When grinding, take care to cool the end being ground by dipping it in water frequently, so tempering is not lost. 1. Bars require little maintenance. They should be thoroughly cleaned after use when they accumulate dirt and grease. 2. 3. They should be covered with light oil before storing in a dry place. The ends of the bars should be kept in shape by filing or grinding to their original shape, because a dull chisel end or claw end makes using the bar more difficult.
42-3/(42-4 blank)
TM 9-243
Chapter 43 MATTOCKS
The Types and Uses section provides you with a list of some of the types of mattocks. These pages should help you select the right mattock to do the job.
The Using section tells you how to use the mattock to perform the desired function. The Care procedures tell you how to care for the item.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . Single-bevel . . . . . . . . . . . . . . . . . . . . . . . Double-bevel . . . . . . . . . . . . . . . . . . . . . . . SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43-2 43-2 43-2 43-2 43-2 43-3
43-1
TM 9-243
TYPES AND USES

SINGLE-BEVEL AND DOUBLE-BEVEL
The mattock is designed for digging and cutting operations. The mattock can have a single or double-beveled head. However, the single-beveled mattock can be combined with other digging tools to perform a variety of functions. For example, the pick-mattock is a combination of the single-beveled mattock and pick.
SAFETY
1. When using a mattock, it is important to have a firm footing and correct posture to prevent the mattock from glancing and striking the feet or legs if the mark is missed. 2. Do not swing a mattock until you are sure that no one will be endangered by the swing, a possible loose head, or glancing of the tool.
USING THE MATTOCK
WARNING WEAR EYE PROTECTION. Distribute body weight equally on both feet. The knees should be set but not tense. The feet should be spread apart at a comfortable distance. The body should be relaxed and free to swing and bend from the hips.
43-2
TM 9-243
USING THE MATTOCK - Continued

2 When practicing using the mattock, swing with
either the right or the left hand leading. When your position becomes tiring, reverse your hands on the handle of the mattock.
3 With the right hand leading, the left foot should be

brought slightly toward the work. To start the swing, hold the handle at the end with the left hand and near the center with the right hand. Raise the mattock over the right shoulder. Swing the mattock down toward the work, allowing the right hand to slide back along the handle toward the left hand so that at the finish of the swing, the hands are close together.
4 With the left hand in the center of the handle, the

mattock is swung in the same manner, except that the positions are reversed.
5 Light swings are accomplished with wrist motion

only, allowing the head of the mattock to do the work.
6 Use the wrists, forearms, and shoulders for heavy

swings. CAUTION Slight prying may be done with the mattock. However, this must be done cautiously to prevent breaking the wood handle.
CARE OF MATTOCKS
1. 2. Clean the mattock thoroughly after use and before short or long-term storage. Store the mattock so that the head will not be struck against metal or other hard surfaces. The mattock should be placed on its head against a wall or hung on a rack for storage. Coat the head with oil. For long-term storage, coat the head with a rustpreventive compound and store in a dry place in a rack or box with the cutting edges protected. 4. WARNING CLOTHS USED TO APPLY OR REMOVE LINSEED OIL ARE FIRE HAZARDS BECAUSE THEY MAY IGNITE BY SPONTANEOUS COMBUSTION, THESE CLOTHS SHOULD BE EITHER DESTROYED AFTER USE OR HUNG UP TO DRY IN A WELLVENTILATED PLACE AND STORED IN METAL CONTAINERS. The raw wood handles of mattocks should be rubbed thoroughly (preferably prior to use) with a cloth soaked in boiled linseed oil. This will prevent drying, checking, and moisture penetration.
3.
43-3/(43-4 blank)
TM 9-243
Chapter 44 GASKET CUTTERS

The Types and Uses section provides you with a list of some of the types of gasket cutters. These pages should help you select the right cutter to do the job.
The Using section tells you how to use the gasket cutter to perform the desired function. The Care procedures tell you how to care for the item.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . 44-2 Circle gasket cutter . . . . . . . . . . . . . . . . . . 44-2 Bit brace circle gasket cutter . . . . . . . . . . 44-2 Hollow gasket cutter . . . . . . . . . . . . . . . . . 44-2 Heavy duty bench mount gasket cutter . 44-2 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44-3 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44-3
44-1
TM 9-243
TYPES AND USES

CIRCLE GASKET CUTTER HOLLOW GASKET CUTTER
The compass-style circle gasket cutter cuts gaskets from 4-inch diameters through 20-inch diameters. It cuts leather, paper, plastic, rubber, sheet lead, or thin wood. It has an aluminum frame with a graduated scale, steel pivot pin, and tempered tool steel knives. It requires a knurled thumb screw adjustment to change diameters.
The hollow gasket cutter is also known as a hollow punch. It is extremely serviceable for cutting soft materials. It comes in a set with a mandrel. The sizes are 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, and 5/8 inch. The set will withstand unlimited use if a hardwood block is used under the gasket material when cutting gaskets. They are not designed for cutting metal or cutting against a hard surface. Other individual hollow gasket cutters are also available.
HEAVY DUTY BENCH MOUNT GASKET CUTTER
BIT BRACE CIRCLE GASKET CUTTER
The bit brace circle gasket cutter adjusts from 1 to 5-1/2 inches in diameter. It cuts metal, plastic, wood, hardwood and other materials. It has a tapered square shank to fit a bit brace. It comes with a 3/16-inch tool steel bit, 1/4-inch pilot drill, and a hex wrench for easy adjustment.
The bench mount gasket cutter is used for heavy duty jobs requiring gaskets cut from the heaviest of materials.
44-2
TM 9-243
USING THE GASKET CUTTER

Below are examples of how several of the gasket cutters in this chapter can be used.
USING A CIRCLE GASKET CUTTER
USING A BIT BRACE CIRCLE GASKET CUTTER
USING A HOLLOW GASKET CUTTER
Cutting circular gasket compass-style.
Cutting smaller circular gasket with a bit brace.
Cutting small holes in gasket with a hollow punch.
CARE OF GASKET CUTTERS

1. 2. After using a gasket cutter, wipe it clean and apply a thin film of oil to prevent rusting. Carefully place the gasket cutter on a shelf, rack or other suitable place to avoid damaging its cutting edges. 3. For long-term storage, coat the gasket cutter with rust-preventive compound. Protect the cutting edges and store carefully in a dry place.
44-3/(44-4 blank)
TM 9-243
Chapter 45 CHOPPING TOOLS

INDEX
Item Page
The Types and Uses section provides you with a list of some of the types of chopping tools. These pages should help you select the right chopping tool to do the job. The Using section tells you how to use chopping tools to perform the desired function. The Care procedures tell you how to care for the item.
TYPES AND USES . . . . . . . . . . . . Single-bit ax . . . . . . . . . . . . . . . . . . . Double-bit ax . . . . . . . . . . . . . . . . . . Crash ax . . . . . . . . . . . . . . . . . . . . . HATCHETS . . . . . . . . . . . . . . . . . . . Half-hatchet . . . . . . . . . . . . . . . . . . . ADZ . . . . . . . . . . . . . . . . . . . . . . . . . . TIMBER WEDGE . . . . . . . . . . . . . . SAFETY . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . .
45-2 45-2 45-2 45-2 45-2 45-2 45-3 45-3 45-3 45-4 45-7
45-1
TM 9-243
TYPES AND USES

AXES
Axes are cutting tools used for the cutting down of trees and for the chopping and splitting of wood. They may be either single or double-edged. Single-bit, double-bit, and crash axes are the most common types. Sizes of axes vary depending upon their design and purpose.
CRASH AX
SINGLE-BIT AX
The crash ax, or firemans ax, is used by emergency personnel to gain quick access to a given area. This ax has a steel head with a cutting blade or bit at one end, and a spike-like extension at the other. The single-bit ax is used to cut down or prune trees. It can also be used to cut or trim logs and heavy brush, or to split and cut wood. This type ax has a steel head attached by wedges to a long, slightly curved handle. The head has a flat face at one end. At the other end is the cutting edge or bit.
HATCHETS
HALF-HATCHET
DOUBLE-BIT AX
The double-bit ax is used for the chopping down and the lopping and topping of trees. The double-bit ax has a wedge-type head with two cutting edges.
The half-hatchet, commonly called a hatchet, has a steel head fastened by wedges to a short wooden handle. The head always has a straight front edge and a round rear shoulder. The other end of the head may vary in shape depending on the design and use.
45-2
TM 9-243

ADZ TIMBER WEDGES
The adz is a chopping tool used for chopping and smoothing lumber or logs where a great deal of wood or bark is to be removed. The adz is a form of ax where the edge of the blade is at a right angle to the handle. It has a curved steel head attached to a curved handle.
The timber wedge is used with a sledge, primarily to split logs and timber. When sawing timber or thick lumber, it may also be used to spread the cut so the saw will not bind. The timber wedge is a steel tool resembling a slender single-bit ax head. One end is slightly fanshaped and sharpened to a dull edge. The other end is flat where a sledge can strike when driving the wedge into a log.
SAFETY
1. 2. 3. 4. Never use any tool that is defective. Always wear eye protection when working where flying particles may injure the eyes. Do not use dull or defective tools. Before swinging a tool, be sure no one is close enough to be injured. 7. 5. 6. Do not use a tool not designed for the job. It can be dangerous. Before using an ax, clean the work area of material that might deflect the ax blade. Keep arms, legs, and feet out of path of ax.
45-3
TM 9-243
USING THE SINGLE-BIT AX
WARNING ALWAYS WEAR SUITABLE EYE PROTECTION.
3 To start the swing, bring the ax back over the right

shoulder, bending the elbow as the right hand slides up the handle toward the ax head.
First clear the work area of material that might deflect the ax blade. The users body weight should be evenly distributed, with knees set, but not tense. The feet should be spread at a comfortable distance to retain balance, while the body should be relaxed and free to swing and bend at the waist. close together near the end of the handle, with the right or leading hand closer to the ax head. The left foot should be closer to the work. NOTE Reverse the position of the hands, feet and shoulder if left-handed.
2 To use the ax, grasp the ax handle with both hands
4 On the downswing, let the right hand slide down the

handle, toward the left hand.
5 At the end of the downswing, the right hand will be

beside the left hand at the end of the handle.
45-4
TM 9-243
USING THE ADZ
WARNING ALWAYS WEAR SUITABLE EYE PROTECTION.
1 To use the adz, first clear the work area of branches

and debris.
4 Use short, choppy down strokes while keeping the

hands in approximately the same position on the handle. The right hand does not slide toward the left hand as in swinging the ax, because the right hand must be in a position to keep control of the adz head at all times. Sliding the right hand to the end of the handle would allow the adz blade face to be deflected toward the user. NOTE As wood chips accumulate on the work surface, clear them away to prevent their causing a deflection of the adz blade. Reverse the position of the hands if lefthanded.
2 Block the timber to be worked on so it cannot slip, 3

slide, or roll. Straddle the timber and grip the adz handle with both hands. The right hand should be held approximately 12 to 15 inches above the left hand.
45-5
TM 9-243
USING THE TIMBER WEDGE
WARNING BEFORE USING ALWAYS WEAR SUITABLE EYE PROTECTION.
4 Give the wedge a few blows, then start a second

wedge on the line farther along the log and drive it with a few sledge blows.
1 To use the timber wedge, first block the log to be

split, or steady it so it cannot roll.
2 With the left hand, hold the wedges narrow edge (1)
on the log where a split is desired. CAUTION Do not use a timber wedge that has nicks or burrs, since the rough sections can scratch the hands or can cause chips to break off when struck by sledge.
5 Alternate driving the wedges into the log until log

splits. For longer logs, more than two wedges should be used. NOTE Reverse the position of the hands if lefthanded.
3 Hold the sledge handle in the right hand, close to its

head, and start driving the wedge (2) into the log with a pounding action.
45-6
TM 9-243
CARE OF CHOPPING TOOLS

1. 2. 3. 4. Clean all chopping tools after use. Store tools to protect heads and cutting edges. For prolonged storage, keep tools free of rust by wiping with oil. In very cold weather, never use a chopping tool before the blade is warm. A cold blade is brittle and will break easily. WARNING LINSEED OIL IS A FLAMMABLE LIQUID. TO AVOID PERSONAL INJURY, PROPERLY DISPOSE OF ALL CLEANING RAGS IN NON-COMBUSTIBLE CONTAINERS. 5. Promptly replace wooden handles on all chopping tools when needed. When changing handles, apply a light coating of linseed oil.
45-7/(45-8 blank)
TM 9-243
Chapter 46 SAWS
The Types and Uses section provides you with a list of some of the types of saws. These pages should help you select the right saw to do the job.
The Using section tells you how to use the saw to perform the desired function. The Care procedures tell you how to care for the item.
INDEX
Item
TYPES AND USES . . . . . . . . . . . . . . . . . Handsaw . . . . . . . . . . . . . . . . . . . . . . . . . . One-man crosscut saw . . . . . . . . . . . . . . Two-man crosscut saw . . . . . . . . . . . . . . Backsaw . . . . . . . . . . . . . . . . . . . . . . . . . . Nested saw . . . . . . . . . . . . . . . . . . . . . . . . Keyhole saw . . . . . . . . . . . . . . . . . . . . . . . Compass saw . . . . . . . . . . . . . . . . . . . . . . Hacksaw . . . . . . . . . . . . . . . . . . . . . . . . . . SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 46-2 46-2 46-2 46-3 46-3 46-3 46-3 46-4 46-4 46-4 46-5 46-7
46-1
TM 9-243
TYPES AND USES

Saws are tools with thin, flat steel blades that have a row of spaced notches or teeth along the edge. The blade is fastened to a handle. Saws are available in various sizes and designs depending on their use and the material to be cut. The most common types of saws are handsaw, (crosscut and ripsaw), backsaw, one-man crosscut saw, two-man crosscut saw, nested saw (keyhole and compass) and hacksaw.
ONE-MAN CROSSCUT SAW
HANDSAW
The handsaw consists of a thin flat blade with teeth and a wooden or plastic handle, called the heel, fastened to the end of the blade by screws. There are two categories of handsaws: the ripsaw (1) and the crosscut (2). The ripsaw is designed to cut with the grain of wood, and the crosscut saw is designed to cut against the grain. The handsaw is used in carpentry, rough-out work, and for finish hand sawing. Sizes of handsaws vary depending on design and nature of the task.
The one-man crosscut saw is about 36 inches long and has a handle at one end. This type of saw is characterized by a high-grade steel blade with two types of teeth known as cutters (1) and rakers (2). The cutters do the cutting, and the rakers chisel out and remove chips from the cut. It is used for heavy work such as cutting down trees and sawing heavy timbers.
46-2
TM 9-243

TWO-MAN CROSSCUT SAW
shape to other hand saws except it is usually mounted higher. Backsaws are used for general bench work such as cutting joints and smaller sections of lumber to length. Sizes vary depending on design and nature of work.
NESTED SAWS
The two-man crosscut saw is 5 to 6-1/2 feet long with a handle at each end. As with the one-man crosscut saw, it also has a high-grade steel blade with the cutter and raker teeth arrangement. It is used when two men are required for extra heavy cutting jobs.
BACKSAW
Nested saws consist of a wooden handle to which several different blades can be attached, making up different types of saws such as the keyhole or compass saw. A slotted end at the heel of each blade slips into the pistol-grip type handle where a wingnut fastens it in place. Nested saws are used to cut along curved lines, to start cuts for larger saws, or to make starting saw cuts from drilled holes or small openings. The size of these saws will vary depending on design and nature of use.
KEYHOLE SAW
The backsaw has a straight blade and parallel top and bottom, with a heavy strip of steel or brass wrapped along the back to provide rigidity. The handle is of similar
The keyhole saw is the smallest type of nested saw. Its blade has a very narrow point small enough to enter a 1/4-inch hole. It is used for close-quarter work, such as cutting, shaping, or enlarging holes in a board.
46-3
TM 9-243

COMPASS SAW HACKSAW
The compass saw is slightly larger than the keyhole saw. The teeth are so arranged that the blade can easily be turned for cutting curves or holes. As with the keyhole saw, the compass saw will vary in size depending on the design and purpose.
The hacksaw is designed to cut almost any size or shape of metal object. The hacksaw uses two types of blades, hard and flexible. The type of blade used depends on the nature of the task. The blade is held to the saw frame by pins that fit into small holes at each end of the blade. Blade tension is adjusted by a screw and wingnut assembly at either the nose or the handle end of the frame. The hacksaw comes in various designs, depending on the purpose.
SAFETY
1. 2. 3. 4. Before using, inspect the tool. Do not use any damaged or broken saw. Store all tools in their proper places when not being used. Wear proper eye protection when using any saw. Do not throw or drop any tools. If a saw is dropped, inspect immediately before reusing. 5. 6. 7. 8. Using clamps or vises, steady or secure any loose material to be cut. Do not allow pointed or edged tools to lie around where they may injure someone. Be careful not to allow the fingers or other parts of body to get in the line of cut. Do not use a tool for any purpose other than that for which it was designed.
46-4
TM 9-243
USING THE CROSSCUT SAW

3
Start the cut by drawing back a few inches of teeth at the heel of the saw a few times.
At approximately a 45 degree angle, saw only on the downward stroke applying pressure evenly.
1 In using the crosscut saw, place the work on a level

just below the knees. Place one sawhorse, bench or other support (1) fairly close to line of cut (2).
5 2
To start the cut, place thumb (3) against the side of the saw blade, being careful to hold it well above teeth.
Keep the saw blade at a right angle to the work surface by checking the saw position occasionally with a try square (4). When nearing end of cut, hold the waste side of the wood to prevent board breaking off unevenly.
46-5
TM 9-243
USING THE KEYHOLE SAW
WARNING WEAR PROPER EYE PROTECTION TO AVOID FLYING WOOD CHIPS OR DEBRIS.
Insert the saw blade (2) and start to cut slowly, with a minimum of pressure. narrow blade will easily bend.
3 Be careful not to twist the blade too sharply, as the
1 To make an inside-out cut, first drill a hole (1) large

enough to admit the point of the saw.
USING THE HACKSAW
WARNING WEAR PROTECTIVE EYEWEAR TO AVOID FLYING METAL CHIPS.
Insert the correct blade (1) in the hacksaw frame (2) and adjust wing nut (3) for proper tension.
46-6
TM 9-243
USING THE HACKSAW - Continued
2 3
Secure the material (4) to be cut in a vise or other holding device to avoid vibration which may snap the blade. To make an accurate cut, use a file (5) to make a notch for guiding the first strokes of the saw.
Steady the saw by holding the handle with the right hand and the frame with the left. on the push stroke, being careful not to bear down too hard. Draw the blade back using no pressure each time.
5 Hold the blade parallel to the work surface and cut
6 Saw at a rate not to exceed 40 to 50 strokes per

minute.
CARE OF SAWS
1. Store blades in a dry place and apply a light coat of oil when not in use. This will keep the blades from rusting. Never use a woodcutting saw to cut through nails or other metal. Between cuts, place saw flat on a work bench or in a spot where teeth cannot be damaged. Avoid placing heavy tools or objects on saw blades as this can result in distortion of the blade. Do not force the saw if it binds. Use a wedge to spread the cut. 10. 6. 7. 8. 9. Replace damaged saw handles with new ones immediately when needed. To keep saw teeth in top condition, touch up the teeth with a file occasionally. Always loosen the blade tension on a hacksaw when not in use. Always protect saw blade teeth from coming in contact with metal or other material that may damage them. Always remove the nested saw blade from the handle for storage.
2. 3. 4. 5.
46-7/(46-8 blank)
TM 9-243
Chapter 47 BRUSH-CUTTING TOOLS

The Types and Uses section provides you with a list of some of the types of brush-cutting tools. These pages should help you select the right brush-cutting tool to do the job.
The Using section tells you how to use the brushcutting tools to perform the desired function. The Care procedures tell you how to care for the item.
INDEX
item Page
TYPES AND USES . . . . . . . . . . Brush hook . . . . . . . . . Machete . . . . . . . . . . . . SAFETY . . . . . . . . . . . . USING . . . . . . . . . . . . . CARE . . . . . . . . . . . . . .
... . . . . . . . . . .
. . . . . .
47-2 47-2 47-2 47-2 47-3 47-3
47-1
TM 9-243
TYPES AND USES

When it is not practical to use an ax or other conventional cutting tool, a brush-cutting tool can be used. Brush-cutting tools are used for cutting underbrush, shrubs, tree branches, vines, and tall grass. Two of the most common brush-cutting tools are the brush hook and the machete. Brush-cutting tools are available in various sizes and designs depending on the nature of use. an ax blade. The brush hook is used for cutting underbrush, shrubs, or branches. Tool size and design vary according to the task.
BRUSH HOOK
MACHETE
The machete normally in military use is an l&inch knife, widest and heaviest at the point of the blade. The blade is attached to a handle shaped to fit the hand. The handle is designed with a slight projection to prevent the machete from slipping from the hand while being used. The machete is used to cut tall grass, vines, and small brush.
The brush hook is a hook-shaped steel blade set onto a heavy-duty metal or wooden handle. The inside edge of the hooked blade is sharpened like the cutting edge of
SAFETY
1. 2. Always make sure no one is close enough to be injured before swinging the tool. Take care not to allow branches or brush in line of swing to deflect the stroke and cause injury. 3. 4. Do not use a dull or defective tool. Store tools properly when not-in use.
47-2
TM 9-243
USING THE BRUSH HOOK
WARNING WEAR PROPER EYE PROTECTION WHEN WORKING WHERE FLYING PARTICLES MAY CAUSE EYE INJURY.
2 To cut small brush or bushes, swing the brush hook

horizontally. The hooked portion will keep the brush from bouncing away from the cutting edge.
1 To use the brush hook on a tree branch, lift the curve

of the hook above the branch and make short, chopping strokes downward against the surface of the branch.
CARE OF BRUSH-CUTTING TOOLS

1. Repair all nicks and dulled cutting edges immediately. 2 . For prolonged storage, coat metal parts with light oil. 3 . Replace defective handle immediately.
47-3/(47-4 blank)
TM 9-243
Chapter 48 TIMBER HANDLING TOOLS

The Types and Uses section provides you with a list of some of the types of timber handling tools. These pages should help you select the right timber handling tool to do the job.
The Using section tells you how to use timber handling tools to perform the desired function. The Care procedures tell you how to care for the item. INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . . 48-2 Timber carrier . . . . . . . . . . . . . . . . . . . . . . . 48-2 Peavy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-2 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48-2 CARE . . . . . . . . . . . . . , . . . . . . . . . . . . . . . . 48-3
48-1
TM 9-243
TYPES AND USES

Timber handling tools are used for lifting or moving heavy objects such as logs or timbers. The timber carrier and the peavy are the most common examples of timber handling tools. feet in length. The timber carrier is used to lift logs and timbers from one level to another as well as carry them.
PEAVY
TIMBER CARRIER
The timber carrier consists of a pair of large chisel-bill hooks with sharp, pointed ends. These hooks are hung by pivots in the center of a large wooden handle, four
The peavy has a sturdy pole-type wooden handle, about 5 feet in length, that fits into a cylindrical tapered steel socket. The socket has a sharp, spiked point. Hinged to the side of the socket is a curved hook that ends in a sharp point. The peavy is used for rolling, turning, and carrying logs and timbers.
SAFETY
1. 2. Be sure that all hooks are securely embedded in the log to be carried. Be sure that all personnel at the end of the timber carrier or peavy handles lift and lower the log in unison. 3. Do not toss tools from one location to another, as damage or injury may result.
USING TIMBER HANDLING TOOLS

Below are examples of how the timber. handling tools in this chapter can be used.
USING A TIMBER CARRIER
USING A PEAVY
Lifting and moving heavy log with timber carriers.
Lifting and moving heavy log with peavies.
48-2
TM 9-243
CARE OF TIMBER HANDLING TOOLS

1. 2. 3. Keep the points on both tools sharp by filing when points are even slightly dulled. Oil the rustable metal portions of these tools on occasion to maintain their good condition. Inspect the pivots on the timber carrier to insure they are tight. 4. 5. WARNING LINSEED OIL IS A FLAMMABLE LIQUID TO AVOID PERSONAL INJURY, PROPERLY DISPOSE OF ALL CLEANING RAGS IN NON-COMBUSTIBLE CONTAINERS Coat the handles occasionally with linseed oil to prevent drying out. Replace defective or damaged handles immediately.
48-3/(48-4 blank)
TM 9-243
Chapter 49 CLIMBING TOOLS

The Types and Uses section provides you with a list of some of the types of climbing tools. These pages should help you select the right climbing tool to do the job.
The Using section tells you how to use climbing tools to perform the desired function. The Care procedures tell you how to care for the item.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . 49-2 Safety belt . . . . . . . . . . . . . . . . . . . . . . . . 49-2 Safety strap . . . . . . . . . . . . . . . . . . . . . . . 49-2 Leg irons . . . . . . . . . . . . . . . . . . . . . . . . . 49-2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . 49-3 USING . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-3 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-5
49-1
TM 9-243
TYPES AND USES

SAFETY STRAP
The safety strap is a leather strap with metal snap hooks on each end. These hooks attach to the D-rings on the safety belt.
LEG IRONS
Climbing tools consist of safety belts (1), safety straps (2) and leg irons with spurs (3). Climbing tools are used for scaling poles and trees, erecting power lines, and for support when clearing and topping trees.
SAFETY BELT
The safety belt is an adjustable leather belt that has loops in which to carry tools. It also has two D-rings (1) attached to hold the safety strap.
The leg irons (1) are often called tree and pole climbers. They consist of flattened metal bars, curved at one end to fit under the foot arch, and with the straight portion along the inside of the lower leg. Leather straps (2) secure the irons to the leg and ankle.
SAFETY
1. 2. 3. Always inspect climbing tools thoroughly before using them. Never climb without using a safety strap. When climbing, insure that the spurs are securely driven into the wood at each stop. 4. 5. Do not use any belt or strap that is cracked or dried-out. Never use a safety belt or safety strap with broken, bent or badly worn rings or fasteners.
49-2
TM 9-243
USING CLIMBING TOOLS
1 Secure safety belt (1) around waist and place tools

needed in position on belt.
3 Snap the safety strap (3) to one D-ring (4) on the

belt, pass the strap around the pole to be climbed, and snap, the other end of the safety strap to the other D-ring (5).
WARNING Before placing your weight on the strap, look to see that the snap and D-ring are properly engaged. Do not rely on the click of the snap-tongue as an indication that the fastening is secure.
2 Strap the leg irons (2) to the legs and feet.
49-3
TM 9-243
USING CLIMBING TOOLS - Continued

7 8 9
While climbing, lean your body away from the pole to prevent the safety strap from slipping. Keep both hands on the pole until the safety strap needs moving. With both gaffs firmly embedded in the pole, slide the safety strap up the pole.
4 5
Begin the climb by driving one leg iron gaff (6) into the pole so the gaff has a solid hold. Place your weight on the embedded gaff and drive the other gaff into the pole a little higher than the first.
10 When desired height isreached, sink both gaffs

into the pole at the same level.
11 Lean back with the safety strap around the pole

slightly higher than the safety belt. Hold this position while working.
6 Begin the climb using the procedure outlined in

step 5.
49-4
TM 9-243
CARE OF CLIMBING TOOLS

1. 2. 3. Keep leather items soft and supple by occasionally applying neats foot oil. Examine all stitching frequently and repair immediately if needed. Inspect D-rings on the safety belt and snap-hooks of the safety strap frequently. 4. 5. 6. 7. Keep spurs sharp by filing after use. Store leather parts away from extreme heat. Oil all metal parts before storing. Lay metal leg irons away so spur points will not be damaged by coming in contact with other tools.
49-5/(49-6 blank)
TM 9-243
Chapter 50 PLANES
The Types and Uses section provides you with a list of some of the types of planes. These pages should help you select the right plane to do the job. The Using section tells you how to use planes to perform the desired function. The Care procedures tell you how to care for the item. INDEX
/tem Page
TYPES AND USES . . . . . . . . . . . . . . . . . . Block plane . . . . . . . . . . . . . . . . . . . . . . . . . Bench plane . . . . . . . . . . . . . . . . . . . . . . . . SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50-2 50-2 50-2 50-2 50-3 50-4
50-1
TM 9-243
TYPES AND USES

Planes are smoothing tools used to true edges or surfaces of wood. Planes also are used where a finished surface or close-fitting joints are required. Planes vary in size and shape, but each is designed for a specific purpose. The two types of planes most generally used are the block plane and bench plane.
BENCH PLANE
BLOCK PLANE
The block plane is the smallest type of plane. It is available in a variety of patterns and is designed to cut end grain with the cutting blade set between 12 degrees and 20 degrees. Although it can usually be used with one hand, a toe knob is provided when additional pressure is needed.
One of the most common types of bench planes is the jack plane. Like all bench planes, the jack plane is designed for cutting with the grain of the wood. Its cutting blade is set at approximately 45 degrees and is used for all purpose planing or to cut lumber to specified lengths.
SAFETY
1. 2. 3. Be careful to plane work smoothly to avoid splinters that may be left to cause injury. Use each plane only for the job it is intended. Keep all cutting tools in good condition. 4. 5. Do not allow tools to lie around work areas in such a position that they may cause injury to others. Before using, inspect the tool for damage or other defects. Repair or replace immediately if required.
50-2
TM 9-243
USING THE BLOCK PLANE

WARNING WEAR EYE PROTECTION WHEN WORKING WHERE FLYING PARTICLES MAY CAUSE EYE INJURY.
1 Secure work with a vise or with clamps to prevent

slippage.
2 Ensure that the cutting blade is extremely sharp and

set to produce a fine cut.
4 Push along the length of the board with a steady,

even stroke. NOTE Plane from either end to prevent the grain splitting or plane a chamfer on the far end first, as shown.
3 Place the plane on the edge of board with the plane

pointing across the grain.
5 Raise the plane from the work after each stroke and
return to the starting point.
6 Repeat the process until the task is complete.
USING THE BENCH PLANE

WARNING WEAR EYE PROTECTION WHEN WORKING WHERE FLYING PARTICLES MAY CAUSE EYE INJURY
1 Secure work with a vise or with clamps to prevent

slippage. 2 Make sure the plane is sharp and properly adjusted before using.
3 Place the plane on the board with the right hand on

the handle and the left hand on the knob. NOTE Reverse the position of the hands if lefthanded.
Check to insure the plane is placed on the work so that the wood grain points in the direction the plane will go.
50-3
TM 9-243
USING THE BENCH PLANE - Continued
Push with a steady, even stroke along the length of the board. each stroke.
7 Repeat the process until the task is completed.
6 Raise the plane and return to the starting point after
CARE OF PLANES
1. 2. Place the plane on its side to protect cutting edge when not in use. Keep the cutting edge sharp and free of nicks. 3. 4. Cover all metal parts with light oil to prevent rusting. For storage, withdraw the cutting edge into the mouth of the plane.
50-4
TM 9-243
Chapter 51 DIGGING TOOLS

The Types and Uses section provides you with a list of some of the types of digging tools. These pages should help you select the right digging tool to do the job.
The Using section tells you how to use digging tools to perform the desired function. The Care procedures tell you how to care for the item.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . Long-handled shovel . . . . . . . . . . . . . . . . . D-handled shovel . . . . . . . . . . . . . . . . . . . Spade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Posthole auger . . . . . . . . . . . . . . . . . . . . . Posthole digger . . . . . . . . . . . . . . . . . . . . SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51-2 51-2 51-2 51-2 51-2 51-2 51-3 51-3 51-5
51-1
TM 9-243
TYPES AND USES

Digging tools are designed for the breaking and digging of soil. Common types of digging tools are the longhandled and D-handled shovel, spade, posthole digger, and auger.
POSTHOLE AUGER
LONG-HANDLED SHOVEL
The long-handled shovel consists of a curved, shaped steel blade attached to a long wooden handle. The lower metal edge of the blade is tapered to help it cut into the ground. The long-handled shovel is used for heavy digging, especially when it is necessary to throw or move dirt a substantial distance.
D-HANDLED SHOVEL
The posthole auger is a long tool made up of a steel shaft that has two shovel-like blades at one end. The blades have curved faces which are hinged to permit slight movement with the concave surfaces of these blades facing each other. The posthole auger is used to bore holes in the ground for posts, poles and explosive charges.
POSTHOLE DIGGER
The D-handled shovel resembles the long-handled shovel except that it has a shorter handle with a D-shaped handgrip at the end. The D-handled shovel is used for light work or for digging in cramped, tight places.
SPADE
The spade, like the shovel, has a steel blade attached to a wooden handle. The blade may be rounded, pointed or square in shape and the handle may have the D or T-shaped handgrip. The spade is used for heavy digging or in confined areas.
The posthole digger has two concave blades similar to the posthole auger except that each blade is fastened to a long, wooden handle. The blades are hinged at the top so that separating the handles will close them and moving the handles together will open them. Like the auger, the posthole digger is used to bore holes in the ground for posts, explosive charges and similar jobs.
51-2
TM 9-243
SAFETY
1. 2. 3. Do not use a dull or defective tool. Before swinging a tool, always be sure no one is close enough to be injured. Store tools properly when not in use. Carelessly stored tools can cause injuries. 4. 5. Use tools correctly so that you and everyone in the vicinity is protected from injury. Do not use a tool not designed for the job.
USING THE LONG-HANDLED SHOVEL
4 Slide one hand near enough to the shovel blade to

raise the weight of the blade and dirt, holding the handle down with the other hand.
1 Hold one hand at the end of the handle, with the

other hand a few inches below it.
2 Press the blade into the ground. Use the foot on top
of the blade for extra force if necessary.
With shovel embedded in soil, push the handle downward and pull back slightly to break the dirt loose.
51-3
TM 9-243
USING THE SPADE
3 Slide one hand near enough to the blade to raise the

weight of the blade and the dirt.
1 Hold the handle upright gripping with both hands

and push the blade into the ground with foot.
2 With the blade in the ground, push the handle

downward and pull back to break the dirt loose.
51-4
TM 9-243
USING THE POSTHOLE DIGGER
1 Drive the posthole digger into the spot where the

hole is to be dug.
3 Pull the handles apart to grasp the earth out of the

hole and lift digger out of hole.
2 Hold the handles slightly separated near the top and

bring the blades down sharply into the soil by force of the arms.
4 Continue the process until the hole is the required

size and depth.
CARE AND CLEANING OF DIGGING TOOLS

1. 2. 3. Tools should be cleaned often after each use and metal parts oiled before storing. Never use a tool other than for the job it was intended. WARNING LINSEED OIL IS A FLAMMABLE LIQUID. TO AVOID PERSONAL INJURY, PROPERLY DISPOSE OF ALL CLEANING RAGS IN NON-COMBUSTIBLE CONTAINERS. 5. Treat wooden handles occasionally with linseed oil to prevent drying out or splintering.
Store all digging tools in their proper places when not in use. 4. Replace defective handles immediately.
51-5/(51-6 blank)
TM 9-243
CHAPTER 52 ELECTRICAL POWER TOOLS

The Types and Uses pages provide you with a list of the electrical power tools found in the pioneer tool outfit. These pages should help you select the right power tool for the job. The Using pages tell you how to best use these tools. By becoming familiar with these procedures, you will build a good background for further skill development in the use of power tools. The Care pages tell you how to keep your power tools in proper working condition. The Safety page tells you how to use your power tools safely and wisely. INDEX
ITEM Page
TYPES AND USES . . . . . . . . . . . . . . . . . 52-2 Portable electric drill . . . . . . . . . . . . . . . . 52-3 Portable electric hammer . . . . . . . . . . . . 52-3 Electric impact wrench . . . . . . . . . . . . . . 52-3 Portable electric circular saw . . . . . . . . 52-4 Portable electric chain saw . . . . . . . . . . 52-4 Portable electric disk sander . . . . . . . . . 52-4 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . 52-4 USING POWER TOOLS . . . . . . . . . . . 52-5 Portable electric drill . . . . . . . . . . . . . . . . 52-5 Portable electric hammer . . . . . . . . . . . . 52-6 Electric impact wrench . . . . . . . . . . . . . 52-7 Portable electric circular saw . . . . . . . . 52-8 Portable electric chain saw . . . . . . . . . . 52-10 Portable electric sander . . . . . . . . . . . . . 52-12 CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52-13
52-1
TM 9-243
TYPES AND USES

Portable electric power tools are designed for a wide variety of uses including construction, tree cutting, bridging, or tree clearing. Electric power tools increase production and reduce time and manpower. Although there are many varieties of electric power tools, only those tools contained in the pioneer tool outfit will be covered in this chapter. They are the electric drill (1), hammer (2) impact wrench (3), circular saw (4) chain saw (5) sander (6), and accessories for these tools. For additional information on power tools not covered in this chapter, refer to FM 9-24.
52-2
TM 9-243

PORTABLE ELECTRIC DRILL
A strong spring inside the housing moves a steel piston back and forth in a pounding motion. The housing muzzle (3) is designed to hold a variety of bits (4) which give the electric hammer great versatility. Examples of possible uses for this tool are beveling, caulking, pounding, digging, and breaking operations.
ELECTRIC IMPACT WRENCH
The portable electric drill is basically an electric motor in a metal housing (1). The housing is fitted with a chuck (2) into which a bit (3) or other attachment can be inserted. The portable electric drill, although varying in size and design, usually has either a spade or pistolgrip handle (4). The portable electric drill is basically designed for drilling. However, by adding various accessories it can be adapted for different jobs. Sanding, sawing, buffing, and polishing are examples of possible uses.
PORTABLE ELECTRIC HAMMER
The portable electric impact wrench consists of a pistol-grip handle (1) on a metal housing (2) which contains a motor that energizes the driving-anvil inside the muzzle of the housing. Attachments (3) are fastened to the driving-anvil by snapping them onto the socket retainer (4). The portable electric wrench with its accompanying equipment is primarily intended for applying and removing nuts, bolts, and screws. It may also be used to drill and tap wood, metal, plastics, etc., and to drive and remove socket head or self-tapping screws.
The portable electric hammer consists of a metal housing (1) with a spade or pistol-grip handle (2).
52-3
TM 9-243

PORTABLE ELECTRIC CIRCULAR SAW
guiding. Unlike the gasoline-powered chain saw, the electric chain saw is designed for lighter work such as tree trimming and cutting small logs and timber.
PORTABLE ELECTRIC DISK SANDER
The portable electric circular saw consists of a sturdy motor in a metal housing (1), a pistol-grip handle (2), and a circular saw blade (3). The trigger switch (4) is built into the handle. Saws vary in size and design depending on the nature of the task. There are many applications for this tool. Typical uses would be cutting studding to length, cutting off end boards, preparing trim, or ripping boards and planks.
ELECTRIC CHAIN SAW
The portable electric disk sander is an electrically driven tool with a spindle (1) at the front end for holding circular attachments (2). Various types of attachments can be fastened to the end of the projecting spindle. The rear end of the sanders housing tapers to form a guiding handle (3). To provide additional control, a second handle (4) is attached to the side of the housing. The portable electric disk sander with its many attachments can be used for a variety of tasks. Heavy-duty sanding, grinding, wire brushing, buffing, and planing are some of the possible applications.
The electrically driven chain saw is a portable power saw with the teeth (1) arranged on a flexible steel chain-like belt (2). It has a pistol-like grip (3) and bar frame (4) above the motor housing (5) for holding and
SAFETY
Before operating any power tool, refer to Chapter 2, Section II for safety guidelines to observe when using these tools. 52-4
TM 9-243
USING THE PORTABLE ELECTRIC DRILL

WARNING BEFORE USING ANY ELECTRICAL TOOL, ALWAYS MAKE CERTAIN THE TOOL IS EQUIPPED WITH PROPER GROUNDING FEATURES. FAILURE TO HAVE PROPER GROUNDING CAN RESULT IN SERIOUS SHOCK.
WARNING ALWAYS WEAR PROPER EYE PROTECTION WHEN WORKING WHERE FLYING PARTICLES MAY CAUSE EYE INJURY.
5 Before drilling, make sure that the work is stationary or firmly secured.
6 Using a punch or awl, make a small prick point (6)

in the spot where the hole will be made. (This will prevent the drill bit from bouncing or slipping away from the spot where the hole is to be drilled.)
Select the proper bit (1) required for the task. NOTE To turn chuck key in either direction a firm grasp of the chuck is required.
7 Connect electric drill (7) to power source. Place

the drill bit on the marked spot and depress trigger switch. Begin drilling, exerting firm but even pressure to keep the bit cutting.
2 Fit the chuck key (2) into the side adjusting hole
between jaws (3) and chuck (4) and turn the key counterclockwise until the chuck opens enough to admit the bit shank (5).
8 Withdraw the bit frequently from the work to clean

chips from the bit flutes (8) and to allow the bit to cool.
3 4
Insert the bit and center the shank in the chuck jaws. Tighten jaws securely by turning the chuck key clockwise. Remove chuck key and store where key will not get lost.
Ease upon the drill pressure as the bit approaches the other side of the work surface. drill bit to prevent binding or breaking. Release trigger switch.
10 After hole is completed, carefully withdraw rotating
52-5
TM 9-243
USING THE PORTABLE ELECTRIC HAMMER

2
WARNING ALWAYS WEAR PROPER EYE PROTECTION WHEN WORKING WHERE FLYING PARTICLES CAN CAUSE EYE INJURY.
Insert attachment into bit retainer (2), and secure in place with locking collar (3). CAUTION TO PREVENT UNNECESSARY WEAR OF PRECISION PARTS AND COMPONENTS, PLACE BIT AGAINST WORK SURFACE BEFORE OPERATING SWITCH.
WARNING THE ELECTRIC HAMMER PRODUCES HAZARDOUS NOISE LEVELS WHEN IN OPERATION. ALWAYS WEAR PROPER PROTECTION TO AVOID POSSIBLE HEARING LOSS.
3 4 1
Select the correct attachment (1) required for the task.
Connect hammer (4) to power source and depress handle trigger. Apply only enough pressure to keep the bit in contact with working surface. Occasionally stop the hammer and clear dust or other residue from the working surface.
52-6
TM 9-243
USING THE IMPACT WRENCH

4 5 6 7
Start the wrench again making sure the driving anvil is now rotating in the opposite direction. Repeat steps 2 through 4 several times to make sure the wrench is reversing consistently. Disconnect impact wrench from power source. Replace the wrench if it does not perform in the above manner.
WARNING ALWAYS WEAR PROPER EYE PROTECTION WHEN WORKING WHERE FLYING PARTICLES CAN CAUSE EYE INJURY. WARNING DO NOT USE STANDARD SOCKETS WITH ANY IMPACT TOOL. THEY CAN SHATTER CAUSING SERIOUS INJURY AND/OR DAMAGE TO THE EQUIPMENT.
8 Select the proper attachment (4) and secure it in

place on the driving anvil.
Before start of work make sure impact wrench and its reversible features are functioning properly in the following manner:
1 2 3
Connect cord to power source. Depress trigger (1) and note the rotating direction of the driving anvil (2). Stop the wrench and adjust the ratchet switch (3) to reverse the direction.
52-7
TM 9-243
USING THE IMPACT WRENCH - Continued
Set the ratchet switch in desired position for anvil rotation required. Reconnect impact wrench to power source.
10 Using both hands, place impact wrench (5) on

work surface (6) and depress trigger.
11 Continue operation until work is completed.

Release trigger to stop wrench.
USING THE PORTABLE ELECTRIC CIRCULAR SAW

WARNING THE ELECTRIC CIRCULAR SAW PRODUCES HIGH NOISE LEVELS WHEN IN OPERATION. ALWAYS WEAR PROPER PROTECTION TO AVOID POSSIBLE HEARING LOSS.
52-8
TM 9-243
USING THE PORTABLE ELECTRIC CIRCULAR SAW - Continued

Select the proper saw blade for the task and attach as follows:
6 1 Make sure power to saw is disconnected. 2 To change saw blades, lock the old blade (1) on the
saw by inserting a punch, screwdriver, nail, etc, in blade hole (2) provided.
Set the saws guides (7) to the correct angle and depth of the cut required.
Remove the old blade by removing the saw clamp screw and flange (3) using wrench (4) provided. Turn the wrench counterclockwise to loosen blade.
Make sure the work (8) to be cut is firmly secured to prevent slippage or movement. scribe, etc., draw a straight line (10) across the work surface to act as a guide for the saw blade to follow.
8 With a marking instrument (9) such as a pencil, pen, 4 5
Install new saw blade (5) on saw, and make sure teeth (6) are in the correct cutting direction (upwards toward saw). Tighten clamp and flange screw by turning wrench clockwise.
52-9
TM 9-243
USING THE PORTABLE ELECTRIC CIRCULAR SAW - Continued
CAUTION The saw blade must be revolving at full speed before it contacts the work surface.
10 11 12
Depress handle trigger (12) to start saw and follow guideline made in step 8. When cutting, apply firm, steady pressure. Be careful not to force the saw. Continue until blade has completed the entire cut. Release trigger to stop saw.
Connect circular saw to power source and place sole plate (11) on work surface.
USING THE ELECTRIC CHAIN SAW

WARNING THE ELECTRIC CHAIN SAW PRODUCES HAZARDOUS NOISE LEVELS WHEN IN OPERATION, ALWAYS WEAR PROPER PROTECTION TO AVOID POSSIBLE HEARING LOSS.
52-10
TM 9-243
USING THE ELECTRIC CHAIN SAW - Continued

WARNING NEVER STAND DIRECTLY BEHIND CHAIN SAW.
5 Stand to the left of the saw (3) with your left hand on
the front handle (4) and your right hand on the rear handle (5). NOTE Reverse the position of the stance and hands if left-handed.
6 1 Make sure power source is disconnected. Before

using, ensure that the chain teeth (1) are in the proper position (saw should cut in direction of arrow). Check the teeth to make sure they are sharp and undamaged.
With your weight evenly distributed, depress trigger to start saw. WARNING WHEN CUTTING, KEEP THE NOSE OF THE GUIDE BAR FROM CONTACTING LOGS, BRANCHES, GROUND OR ANY OTHER OBSTRUCTION. THIS CAN CAUSE "KICKBACK" WHICH IS A QUICK AND DANGEROUS UPWARD MOVEMENT OF THE GUIDE BAR AND SAW CHAIN. CAUTION The saw chain should be at maximum speed before contacting working surface.
Cut with the spike bar (6) set firmly against the wood and apply light pressure. until cut is completed.
8 Continue to guide the chain saw through the work
3 Ensure that the work (2) is stationary and well

secured to prevent slippage or movement.
4 Connect chain saw to power source.
52-11
TM 9-243
USING THE PORTABLE ELECTRIC SANDER

2 Make sure the work surface (4) is secured to prevent movement.
3 Connect sander to power source. Depress switch

(5) on the sander so that the attachment is turning before placing it on the work surface. CAUTION Using excessive pressure will slow up the sanding action, clog the disk, and cause motor to overheat.
4 With one hand on each handle (6) and (7), begin

WARNING THE ELECTRIC SANDER PRODUCES HAZARDOUS NOISE LEVELS WHEN IN OPERATION. ALWAYS WEAR PROPER, PROTECTION TO AVOID POSSIBLE HEARING LOSS. sweeping the sander (8) back and forth across the work surface.
5 During operation, tilt the sander slightly so the entire

disk does not contact the work surface.
6 Brush or clean the sanding dirt from the work surface frequently.
7 When finished, lift the sander from the work surface

before turning off the switch.
1 Select the proper attachment (1) and secure it to the

spindle (2) by depressing locking button (3) and tightening spindle as shown.
52-12
TM 9-243
CARE OF ELECTRIC POWERTOOLS

In order to achieve and maintain maximum performance, all electrical power tools must be given proper care. The following is a list of guidelines that will help keep your power tools in a ready to use condition. 1. Keep all power tools, especially the housing intake and exhaust holes, clear and free of dust and dirt at all times. Examine power tool cords for exposed loose wires and for damaged insulation. 3. 4. 5. 6. 7. Wipe power cords frequently to prevent deterioration from oil or grease. Check cord plugs for loose prongs or cracked casings. Never hold or drag electrical tools by the cord at any time. To prevent rusting, apply a light coat of oil to cutting surfaces of tools. Store power tools in properly designated containers when not is use.
2.
52-13/(52-14 blank)
TM 9-243
Chapter 53 MISCELLANEOUS TOOLS

The Types and Uses section provides you with a list of some of the types of miscellaneous tools. These pages should help you select the right miscellaneous tool to do the job.
The Using section tells you how to use these various tools to perform the desired function. The Care procedures tell you how to care for the item.
INDEX
Item Page
TYPES AND USES . . . . . . . . . . . . . . . . . Cement trowel . . . . . . . . . . . . . . . . . . . . . Brick trowel . . . . . . . . . . . . . . . . . . . . . . . . . Miners spoon . . . . . . . . . . . . . . . . . . . . . . . Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trip wire grapnel . . . . . . . . . . . . . . . . . . . . Chain assembly . . . . . . . . . . . . . . . . . . . . Cable jaw grip . . . . . . . . . . . . . . . . . . . . . . Tension puller . . . . . . . . . . . . . . . . . . . . . . SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53-2 53-2 53-2 53-2 53-2 53-3 53-3 53-3 53-3 53-4 53-4 53-7
53-1
TM 9-243
TYPES AND USES

CEMENT TROWEL BLOCKS
The cement trowel is a flat rectangular blade fastened by a metal strap and shank to a wooden handle. It is used in concrete work for leveling, smoothing, or pushing wet cement into place.
BRICK TROWEL
This type of trowel has a pointed flat blade at one end, and a steel shank that attaches to a wooden handle at the other. The brick trowel is used to scoop and spread mortar.
MINERS SPOON
Blocks are used in combination with rope and wire to hoist and move loads. The block consists of a metal shell which supports both ends of a pin. The shell also houses a grooved pulley that revolves on the pin. Attached at one end of the first block is a freely revolving hook. Blocks may be classified as single, double, triple, etc. according to the number of pulleys housed in the shell of the block. Depending on the various combinations of blocks available to do the job, the mechanical advantage can be increased indefinitely.
The miners spoon is used to lift material out of narrow deep holes, in order to clear for further drilling or to permit placing of explosive charges. The miners spoon is a slender metal rod with the ends forged into small bowl-shaped projections at right angles to the rod.
53-2
TM 9-243

TRIP WIRE GRAPNEL CABLE JAW GRIP
The trip wire grapnel is a metal weight resembling three or four fish hooks, with a common shank ending in an eye. The hooks spread out in different directions at the other end of the shank. Attached to the eye portion of the shank is a marlin cord of varying length. The grapnel is used to trip wires designed to go off on contact, to find. booby traps, or to detonate mines.
The cable jaw grip is used to tighten or stretch wires or cables for various operations. Examples of application include removing kinks or bends in cables, tightening cables on loads or bales, or for cleaning and oiling of cables. Cable grips, depending on their application, vary in size and design.
CHAIN ASSEMBLY
TENSION PULLER
The chain assembly is a heavy duty linked chain with a grab hook at one end and a ring at the other. The chain assembly is used for such applications as towing vehicles, slinging loads, and hauling objects. The chain assembly is available in a wide variety of lengths and link sizes depending on the nature of the use.
Like the cable jaw grip, the tension puller is used to tighten or stretch cables. The tension puller has strong cable (1) attached to a cable notch gear (2). At the end of the cable is a hook (3). This hook (3) can be attached to the eyelet of the cable to be tightened. Tension is then applied to the cable by moving the tension handle (4) in an up and down motion.
53-3
TM 9-243
SAFETY
1. Wash brick trowel, thoroughly wash all mix dust from skin, and remove dusty clothing when finished. Dust ingredients can burn the skin or cause eye injury. When using the tension puller, be sure the hook (or hooks) is of correct size to hold the cable snugly. 3. 4. 5. When swinging the trip wire grapnel, hold the rotating tool at a safe distance from the arm. Be sure tackle used with blocks is safe and meets lifting requirements. Use each tool only for its designated purpose.
2.
USING THE BRICK TROWEL
Hold the trowel with thumb on top of handle (1) for balance and control.
3 4
Slide the trowel under the mortar, seating it firmly on the blade (3) with a slight jerk of the wrist. Hold the edge of the blade over the center of the
work surface.
Slice off a trowel load of mortar (2).
Move the trowel steadily backward, tilting it to slide the mortar gradually from the blade (3), leaving an even bed of mortar on the work surface.
53-4
TM 9-243
USING THE BRICK TROWEL - Continued
Cut off excess mortar after each application by holding the trowel blade (3) slightly angled against the work surface and moving forward. NOTE Excess mortar should be returned to mortar board or applied to any gaps or uneven areas in the mortar bed.
Cut off any excess mortar.
7 To allow enough movement to position bricks,

groove the mortar bed with the point (4) of the trowel.
10 Lay enough bricks to cover the mortar bed and tap 8 Using the trowel, coat the brick ends (5) with mortar before laying them in place. into line using a builders level (6).
53-5
TM 9-243
USING THE BLOCK
1 Secure one end of the rope or ropes to the load (1)

to be moved.
Pass the other end of the rope over the pulley (2) of the block attached to some type of solid support. rope to lift the load.
3 Apply the necessary manpower to the end of the
USING THE CABLE JAW GRIP AND TENSION PULLER
1 Place end of cable (1) between jaws (2) of cable jaw

grip (3) (from jaw end of tool).
Hold the jaws (2) together over cable (1). Apply pressure with tension puller handle (6). the jaws (2) hold the cable firmly.
4 Apply pressure until cable (1) is stretched to make 5

Continue pressure using handle of tension puller (6) until desired pressure is reached.
Fasten eye (4) to tension puller hook (5).
53-6
TM 9-243
CARE OF MISCELLANEOUSTOOLS
1. 2. 3. Clean all tools thoroughly after using. Store tools in approved areas to prevent damage. Oil all rustable metal parts of tools before storing. WARNING LINSEED OIL IS A FLAMMABLE LIQUID. TO AVOID PERSONAL INJURY, PROPERLY DISPOSE OF ALL CLEANING RAGS IN NON-COMBUSTIBLE CONTAINERS. 4. Prevent wooden parts of tools from drying out by applying linseed oil occasionally. 5. 6. 7. 8. 9. Do not use a brick trowel to pry bricks or rocks loose. Never oil pulley grooves. Inspect tools frequently, especially pins in blocks. Never use a damaged chain assembly. Replace damaged chain links promptly. Always use the proper size and design of cable jaw grips for each task. Using the wrong size or style can be dangerous.
53-7/(53-8 blank)
TM 9-243
APPENDIX A REFERENCES
A-1. PUBLICATION INDEXES. The following indexes should be consulted frequently for latest changes or revisions of references given in this appendix and for new publications relating to material covered in this manual. DA Pam 108-1 . . . . . . . . . . . . . . . . . . . . Military Publications: DA Pam 310-1 . . . . . . . . . . . . . . . . DA Pam 750-10. . . . . . . . . . . . . . . . A-2. SUPPLY CATALOGS. Class 5110, 20 IL ................. Class 5110 Hand Tools Nonedged, Nonpowered 5120 Fuels, Lubricants, Oils and Waxes Hand Tools, Power Driven, 5130; Drill Bits, Counterbores, and Countersinks: Hand and Machine, 5133; Taps, Dies and Collets: Hand and Machine, 5136; Tools and Hardware Boxes, 5140; and Sets, Kits, and Outfits of Handtools Hardware and Abrasives; Disks and Stones, Abrasive Measuring Tools Metalworking Machinery Woodworking Machinery and Equipment Recommended Changes to Equipment Technical Publications SC 9100 IL . . . . . . . . . . . . . . . . . . . . . . . SC 5130, 33, 36, 40, 80 IL . . . . . . . . Consolidated Index of Army Publications and Blank Forms US. Army Equipment Index of Modification Work Orders Index of Army Motion Pictures and Related Audio-Visual Aids
SC 5345, 50 IL . . . . . . . . . . . . . . . . . . . . SC 5200 IL . . . . . . . . . . . . . . . . . . . . . . . SC 3400 IL . . . . . . . . . . . . . . . . . . . . . . . SC 3200 IL . . . . . . . . . . . . . . . . . . . . . . . A-3. FORMS. DA Form 2028-2 ..................
A-4. OTHER PUBLICATIONS. The following explanatory publications contain information pertinentto this material and associated equipment. TM 38-750 . . . . . . . . . . . . . . . . . . . . . . . FM 43-4 . . . . . . . . . . . . . . . . . . . . . . . . . . AR 310-5 . . . . . . . . . . . . . . . . . . . . . . . . . FM 9-24 . . . . . . . . . . . . . . . . . . . . . . . . . . FM 43-2 . . . . . . . . . . . . . . . . . . . . . . . . . . The Army Maintenance Management System (TAMMS) Common Wood and Metal Repair Dictionary of United States Army Terms (TC 21-5-7) Fundamentals of Machine Tools Metal Body Repair and Related Operations
A-1
TM 9-243
FM 21-30 . . . . . . . . . . . . . . . . . . . . . . . . . AR 310-50 . . . . . . . . . . . . . . . . . . . . . . . . FM 43-3 . . . . . . . . . . . . . . . . . . . . . . . . . . Safety: AR 385-40 . . . . . . . . . . . . . . . . . . . . . . . .
Military Symbols AFM 55-3 Military Terms, Abbreviations, and Symbols: Authorized Abbreviations and Brevity Codes Shop Mathematics
Accident Reporting and Records
A-2
TM 9-243
ALPHABETICAL INDEX
A
Subject Page Subject Page
Adjustable Parallel . . . . . . . . . . . . . . . . . . . . . . Adz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Angle Plates . . . . . . . . . . . . . . . . . . . . . . . . . . . Auger, Post Hole . . . . . . . . . . . . . . . . . . . . . . . Awls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Saddlers . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scratch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Axes Crash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Double-Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . Half-Hatchet . . . . . . . . . . . . . . . . . . . . . . . . . Single-Bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . B
9-2 45-3 9-2 51-2 31-1 31-2 31-2 45-2 45-2 45-2 45-2
Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 - 1 Combination . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 - 2 Crowbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 - 2 Pinch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 - 2 Wrecking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 - 2 Bearing and Bushing Puller, Universal . . . . 4 1 - 2 Bearing Puller, Electrical Unit . . . . . . . . . . . . 4 1 - 2 Benders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 0 - 1 Hand Tube . . . . . . . . . . . . . . . . . . . . . . . . . . 4 0 - 2 Electrical Conduit Hand . . . . . . . . . . . . . . . 4 0 - 2 Spring Tube . . . . . . . . . . . . . . . . . . . . . . . . . 4 0 - 2 Bevel Protractor . . . . . . . . . . . . . . . . . . . . . . . . 1 3 - 4 Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 - 2 Bolt and Cable Cutters . . . . . . . . . . . . . . . . . . 3 2 - 1 Angular Cut . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 - 3 Center Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 - 2 Clipper Cut . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 - 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 - 4 Shear Cut, Flat Bar, and Strip . . . . . . . . . . 3 2 - 2 Shear Cut Cable . . . . . . . . . . . . . . . . . . . . . 3 2 - 3 Side Nut Splitter . . . . . . . . . . . . . . . . . . . . . . 3 2 - 3 Brush-Cutting Tools . . . . . . . . . . . . . . . . . . . . . 4 7 - 1 Brush Hook . . . . . . . . . . . . . . . . . . . . . . . . . . 4 7 - 2 Machete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 7 - 2 C Cable Jaw Grip . . . . . . . . . . . . . . . . . . . . . . . . 53-3
Calipers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hermaphrodite . . . . . . . . . . . . . . . . . . . . . . . Simple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spring-Joint . . . . . . . . . . . . . . . . . . . . . . . . . . Trammels . . . . . . . . . . . . . . . . . . . . . . . . . . . Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vernier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Care of Awls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bench Grinders . . . . . . . . . . . . . . . . . . . . . . Benders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bolt and Cable Cutters . . . . . . . . . . . . . . . . Brush-Cutting Tools . . . . . . . . . . . . . . . . . . . C-Clamps . . . . . . . . . . . . . . . . . . . . . . . . . . Calipers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chisels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chopping Tools . . . . . . . . . . . . . . . . . . . . . . Climbing Tools . . . . . . . . . . . . . . . . . . . . . . . Digging Tools . . . . . . . . . . . . . . . . . . . . . . . . Dividers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric Power Tools . . . . . . . . . . . . . . . . . . Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gage Blocks . . . . . . . . . . . . . . . . . . . . . . . . . Gasket Cutters . . . . . . . . . . . . . . . . . . . . . . . Glass Cutters . . . . . . . . . . . . . . . . . . . . . . . . Grinders and Sharpening Stones . . . . . . . Hammers . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand Screw Clamps . . . . . . . . . . . . . . . . . . . Inserted Face Hammer . . . . . . . . . . . . . . . . Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Knives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual Drills . . . . . . . . . . . . . . . . . . . . . . . . . Mattocks . . . . . . . . . . . . . . . . . . . . . . . . . . . Micrometers . . . . . . . . . . . . . . . . . . . . . . . . . Miscellaneous Measuring Gages . . . . . . . Miscellaneous Measuring Tools . . . . . . . . Miscellaneous Tools . . . . . . . . . . . . . . . . . . Pipe Cutters and Threading Sets . . . . . . . Planes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pliers and Tongs . . . . . . . . . . . . . . . . . . . . . Plumb Bobs . . . . . . . . . . . . . . . . . . . . . . . . . . Pullers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Punches . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1 6-2 6-2 6-3 6-2 6-4 6-2 6-3 31-2 42-3 29-6 40-4 32-5 47-3 19-3 6-5 26-5 45-7 49-5 51-5 5-3 52-13 28-5 15-9 44-3 33-4 29-6 21-12 19-3 21-13 20-7 34-4 23-4 43-3 7-6 16-9 9-3 53-7 35-6 50-4 17-5 11-6 41-5 27-6
Index 1
TM 9-243
Subject Page Subject
D
Page
Care of (cont): Reamers . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ring and Snap Gages . . . . . . . . . . . . . . . . Rules and Tapes . . . . . . . . . . . . . . . . . . . . . Saws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scrapers . . . . . . . . . . . . . . . . . . . . . . . . . . . . Screw and Tap Extractors . . . . . . . . . . . . . Screwdrivers . . . . . . . . . . . . . . . . . . . . . . . . . Scribers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sharpening Stones . . . . . . . . . . . . . . . . . . . Shears and Nippers . . . . . . . . . . . . . . . . . . Snap Gages . . . . . . . . . . . . . . . . . . . . . . . . . Squares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Surface, Height, and Depth Gages . . . . . Taps and Dies . . . . . . . . . . . . . . . . . . . . . . . Timber Handling Tools . . . . . . . . . . . . . . . . Tube Cutters and Flaring Tools . . . . . . . . Vises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wrenches . . . . . . . . . . . . . . . . . . . . . . . . . . . Catapunch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chain Assembly . . . . . . . . . . . . . . . . . . . . . . . . Chisels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Machinists . . . . . . . . . . . . . . . . . . . . . . . . . . Rivet Buster . . . . . . . . . . . . . . . . . . . . . . . . . Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Woodworkers . . . . . . . . . . . . . . . . . . . . . . . . Chopping Tools . . . . . . . . . . . . . . . . . . . . . . . . Adz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Crash Ax . . . . . . . . . . . . . . . . . . . . . . . . . . . . Double-Bit Ax . . . . . . . . . . . . . . . . . . . . . . . . Half-Hatchet . . . . . . . . . . . . . . . . . . . . . . . . . Single-Bit Ax . . . . . . . . . . . . . . . . . . . . . . . . . Timber Wedges . . . . . . . . . . . . . . . . . . . . . . Clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-Clamps . . . . . . . . . . . . . . . . . . . . . . . . . . Hand Screw . . . . . . . . . . . . . . . . . . . . . . . . . Clamp Pliers . . . . . . . . . . . . . . . . . . . . . . . . . . . Climbing Tools . . . . . . . . . . . . . . . . . . . . . . . . . Leg irons . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Strap . . . . . . . . . . . . . . . . . . . . . . . . . Combination Bar . . . . . . . . . . . . . . . . . . . . . . . Crowbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cutter Set, Thread . . . . . . . . . . . . . . . . . . . . . . Cutters, Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . Cutters, Tube . . . . . . . . . . . . . . . . . . . . . . . . . . 39-4 15-9 8-3 46-7 30-3 24-3 22-8 12-3 29-6 37-4 15-9 13-8 14-5 38-7 48-3 36-4 18-5 25-18 27-3 53-3 26-1 26-2 26-2 26-2 26-2 45-1 45-3 45-2 45-2 45-2 45-2 45-3 19-1 19-2 19-2 25-10 49-1 49-2 49-2 49-2 42-2 42-2 38-4 35-2 36-2
Dies, Taps and . . . . . . . . . . . . . . . . . . . . . . . . . Rethreading . . . . . . . . . . . . . . . . . . . . . . . . . Round-Split Adjustable . . . . . . . . . . . . . . . . Thread Cutter Set . . . . . . . . . . . . . . . . . . . . Two-Piece, Collet . . . . . . . . . . . . . . . . . . . . . Digging Tools . . . . . . . . . . . . . . . . . . . . . . . . . . D-Handled Shovel . . . . . . . . . . . . . . . . . . . . Long-Handled Shovel . . . . . . . . . . . . . . . . . Posthole Auger . . . . . . . . . . . . . . . . . . . . . . . Posthole Digger . . . . . . . . . . . . . . . . . . . . . . Disk Sander, Portable Electric . . . . . . . . . . . Dividers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Drill, Portable Electric . . . . . . . . . . . . . . . . . . . Drills, Manual . . . . . . . . . . . . . . . . . . . . . . . . . . Brace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Breast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E Electrical Power Tools . . . . . . . . . . . . . . . . . . Electric Chain Saw . . . . . . . . . . . . . . . . . . . Electric Impact Wrench . . . . . . . . . . . . . . . . Portable Electric Circular Saw . . . . . . . . . . Portable Electric Disk Sander . . . . . . . . . . Portable Electric Drill . . . . . . . . . . . . . . . . . . Portable Electric Hammer . . . . . . . . . . . . . Extractors, Screw and Tap . . . . . . . . . . . . . . Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ear Protection . . . . . . . . . . . . . . . . . . . . . . . . . . Eye Protection . . . . . . . . . . . . . . . . . . . . . . . . . F Factors To Consider . . . . . . . . . . . . . . . . . . . . Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . American Pattern . . . . . . . . . . . . . . . . . . . . . Curved-Tooth . . . . . . . . . . . . . . . . . . . . . . . . Mill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pillar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Round . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Square . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Swiss Pattern . . . . . . . . . . . . . . . . . . . . . . . . Taper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38-1 38-3 38-4 38-4 38-3 51-1 51-2 51-2 51-2 51-2 52-4 5-1 5-2 5-2 52-3 23-1 23-2 23-2 23-2
52-1 52-4 52-3 52-4 52-4 52-3 52-3 24-1 24-2 24-2 2-4 2-4
15-8 28-1 28-2 28-3 28-2 28-2 28-2 28-2 28-3 28-2
Index 2
TM 9-243
Three-Square . . . . . . . . . . . . . . . . . . . . . . . . Warding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flaring Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . Folding Rules . . . . . . . . . . . . . . . . . . . . . . . . . . G Gages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Drill Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fillet and Radius . . . . . . . . . . . . . . . . . . . . . Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Micrometer Depth . . . . . . . . . . . . . . . . . . . . Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rule Depth . . . . . . . . . . . . . . . . . . . . . . . . . . Screw Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . Small Hole Gage Set . . . . . . . . . . . . . . . . . Snap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Telescoping . . . . . . . . . . . . . . . . . . . . . . . . . . Thickness (Feeler) . . . . . . . . . . . . . . . . . . . . . Thread Cutting Tool . . . . . . . . . . . . . . . . . . Vernier Depth . . . . . . . . . . . . . . . . . . . . . . . . . Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gage Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . Gaging Flat Parts . . . . . . . . . . . . . . . . . . . . . . . Gasket Cutters . . . . . . . . . . . . . . . . . . . . . . . . . Bit Brace Circle . . . . . . . . . . . . . . . . . . . . . . Circle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heavy Duty Bench Mount . . . . . . . . . . . . . Hollow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glass Cutters . . . . . . . . . . . . . . . . . . . . . . . . . . . Circle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel Type . . . . . . . . . . . . . . . . . . . . . . . . . . Gloves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grapnel, Trip Wire . . . . . . . . . . . . . . . . . . . . . . Grinders and Sharpening Stones . . . . . . . . . Bench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sharpening Stones . . . . . . . . . . . . . . . . . . . Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H
28-2 28-3 36-2 8-2
16-1 16-2 16-5 16-4 16-4 14-3 16-5 14-2 15-3 14-2 16-3 16-3 15-3 14-2 16-3 16-2 16-4 14-3 16-4 15-4 15-6 44-1 44-2 44-2 44-2 44-2 33-1 33-2 33-2 2-4 53-3 29-1 29-2 29-3 29-2
Carpenters . . . . . . . . . . . . . . . . . . . . . . . . . . 21-2 Dead Blow . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-7 Electric, Portable . . . . . . . . . . . . . . . . . . . . . 52-3 Inserted Soft-Faced . . . . . . . . . . . . . . . . . . . 21-5 Jewelers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-4 Lead or Copper . . . . . . . . . . . . . . . . . . . . . . . 21-5 Machinists Peen . . . . . . . . . . . . . . . . . . . . . 21-2 Masons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-4 Napping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-4 Riveting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-4 Sawmakers . . . . . . . . . . . . . . . . . . . . . . . . . 21-4 21-5 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Soft-Faced . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-5 21-6 Trimmers . . . . . . . . . . . . . . . . . . . . . . . . . . Welders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-6 Hacksaw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-4 Hatchet, Half . . . . . . . . . . . . . . . . . . . . . . . . . . . 45-2 Helmets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Holder, Magnetic Base Indicator . . . . . . . . . . 9-2 How To Use A Box Wrench . . . . . . . . . . . . . 25-14 How To Use Precision Gage Blocks . . . . . . 15-7 How To Use This Manual . . . . . . . . . . . . . . . . 1-1
I Indicators, Speed Registering . . . . . . . . . . . . 9-3 Installation of New Handle . . . . . . . . . . . . . . . 21-14 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 J Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . Ratchet Lever . . . . . . . . . . . . . . . . . . . . . . . . Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K Knives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Draw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Putty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rubber Cutting . . . . . . . . . . . . . . . . . . . . . . . Saddlers . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-1 34-3 34-2 34-3 34-2 34-2 34-2 20-1 20-3 20-3 20-2
21-1 Hammers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blacksmiths or Sledge . . . . . . . . . . . . . . . 21-3 Bumping Body . . . . . . . . . . . . . . . . . . . . . . . 21-3
Index 3
TM 9-243 L
Leg Irons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-2 Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 Carpenters . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 Iron Bench . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 Machinists . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 Master Precision . . . . . . . . . . . . . . . . . . . . . . 10-2 Striding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 M Machete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47-2 Machine, Metal Shearing . . . . . . . . . . . . . . . . 37-2 Magnetic Base Indicator Holder . . . . . . . . . . 9 - 2 Mattocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-1 Single-Bevel and Double-Bevel . . . . . . . . 43-2 Pick-Mattock . . . . . . . . . . . . . . . . . . . . . . . . . 43-2 Mallets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-7 Carpenters . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-7 Rawhide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-7 Rubber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-7 Tinners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-7 Manual Drills . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-1 Brace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-2 Breast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-2 Hand Drill . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-2 Mauls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-8 Railroad Track . . . . . . . . . . . . . . . . . . . . . . 21-8 Wooden . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-8 Method of Filing . . . . . . . . . . . . . . . . . . . . . . . . 28-4 Draw Filing . . . . . . . . . . . . . . . . . . . . . . . . . . 28-4 Micrometers . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1 Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2 Inside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2 Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2 Miners Spoon . . . . . . . . . . . . . . . . . . . . . . . . . 53-2 Miscellaneous Measuring Gages . . . . . . . . . 16-1 Miscellaneous Measuring Tools . . . . . . . . . . 9 - 1 Adjustable Parallel . . . . . . . . . . . . . . . . . . . . 9 - 2 Angle Plate . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 2 Magnetic Base Indicator Holder . . . . . . . . 9 - 2 Registering Speed Indicators . . . . . . . . . . 9 - 2 V-Block and Clamp . . . . . . . . . . . . . . . . . . . 9 - 2 Miscellaneous Tools . . . . . . . . . . . . . . . . . . . . 53-1 Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53-2
Brick Trowel . . . . . . . . . . . . . . . . . . . . . . . . . Cable Jaw Grip . . . . . . . . . . . . . . . . . . . . . . Cement Trowel . . . . . . . . . . . . . . . . . . . . . . . Chain Assembly . . . . . . . . . . . . . . . . . . . . . . Miners Spoon . . . . . . . . . . . . . . . . . . . . . . . Tension Puller . . . . . . . . . . . . . . . . . . . . . . . Trip Wire Grapnel . . . . . . . . . . . . . . . . . . . . N
53-2 53-3 53-2 53-3 53-2 53-3 53-3
Nippers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-2 Cutting Nippers . . . . . . . . . . . . . . . . . . . . . . 37-3 P Parts of a Hammer . . . . . . . . . . . . . . . . . . . . . 21-2 48-2 Peavy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pinch Bar 35-1 . . . . . . . . . Pipe Cutting and Threading Tools 35-2 . . . . . . . . . . . . . . . . . . . . . . . . . Pipe Cutters . . . . . . . . . . . . . . . . . . . 35-2 Pipe Threading Set 50-1 Planes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-2 Bench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-2 Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-3 . . . . . . . . . . . . . . . . . . . . . . . . . . Plate, Surface . . . . . . . . . . . . . . . . . . . . . . . 17-1 Pliers and Tongs 17-2 . . . . . . . . . . . . . . . . . . . . . . Diagonal Cutting 17-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . End Cutting 17-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flat-Nose . . . . . . . . . . . . . . . . . 17-2 Linemans Side Cutting 17-2 . . . . . . . . . . . . . . . . . . . . . . . . . Parallel Jaw 17-2 . . . . . . . . . . . . . . . . . . . . . . . . . . Round-Nose 17-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . Slip-Joint 17-3 . . . . . . . . . . . . . Straight-Lip Flat-Jaw Tongs . . . . . . . . . . .17-3 Wire Strippers (Multipurpose) Pliers, Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . 25-10 Plumb Bobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 Solid Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2 Surveyors Polished Brass . . . . . . . . . . . . . .11-2 Preparing the Work Surface . . . . . . . . . . . . . 22-6 Protractor, Bevel . . . . . . . . . . . . . . . . . . . . . . . . 13-4 Power Tools, Electrical . . . . . . . . . . . . . . . . . . 52-1 Precision Gage Blocks, How To Use . . . . . . . 15-7 Pullers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41-1 Battery Terminal and Small Gear . . . . . . . 41-2 Cotter Pin . . . . . . . . . . . . . . . . . . . . . . . . . . 41-4 Cylinder Sleeve . . . . . . . . . . . . . . . . . . . . . . 41-3 Electrical Unit Bearing . . . . . . . . . . . . . . . . 41-2 Gear and Bearing . . . . . . . . . . . . . . . . . . . . 41-2
Index 4
TM 9-243
Slide Hammer . . . . . . . . . . . . . . . . . . . . . . . . Steering Gear Arm . . . . . . . . . . . . . . . . . . . Universal Bearing and Bushing . . . . . . . . . Universal Gear . . . . . . . . . . . . . . . . . . . . . . . Puller Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Push and Pull . . . . . . . . . . . . . . . . . . . . . . . . Steering Wheel . . . . . . . . . . . . . . . . . . . . . . . Wheel Puller . . . . . . . . . . . . . . . . . . . . . . . . . Punches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . Catapunch . . . . . . . . . . . . . . . . . . . . . . . . . . . Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Drift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Drive Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grommet-Inserting . . . . . . . . . . . . . . . . . . . . Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Metal Cutting . . . . . . . . . . . . . . . . . . . . . . . . Prick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sheet Metal . . . . . . . . . . . . . . . . . . . . . . . . . . Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tinmens Hollow . . . . . . . . . . . . . . . . . . . . . . Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R Reading Measuring Scales. . . . . . . . . . . . . . . . . . . . . Metric Caliper . . . . . . . . . . . . . . . . . . . . . . . . Metric Micrometer . . . . . . . . . . . . . . . . . . . . Metric Rule . . . . . . . . . . . . . . . . . . . . . . . . . Rule or Tape . . . . . . . . . . . . . . . . . . . . . . . . . Standard Micrometer . . . . . . . . . . . . . . . . . . Vernier Caliper . . . . . . . . . . . . . . . . . . . . . . . Vernier Micrometer . . . . . . . . . . . . . . . . . . . Reamers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adjustable-Blade . . . . . . . . . . . . . . . . . . . . . Expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solid Straight-Hole . . . . . . . . . . . . . . . . . . . . Solid Taper-Pin . . . . . . . . . . . . . . . . . . . . . . Registering Speed Indicators . . . . . . . . . . . . Replacing the Handle, File . . . . . . . . . . . . . . . Replacing the Handle, Hammer . . . . . . . . . . Ring and Snap Gages and Gage Blocks . . Gage Blocks . . . . . . . . . . . . . . . . . . . . . . . . . Ring Gages . . . . . . . . . . . . . . . . . . . . . . . . Snap Gages . . . . . . . . . . . . . . . . . . . . . . . .
41-4 41-2 41-2 41-2 41-1 41-3 41-3 41-3 27-1 27-2 27-3 27-2 27-2 27-2 27-3 27-3 27-3 27-2 27-3 27-3 27-3 1-1
Rules and Steel Tapes . . . . . . . . . . . . . . . . . . Folding Rules . . . . . . . . . . . . . . . . . . . . . . . . Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Steel Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . S Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bolt and Cable Cutters . . . . . . . . . . . . . . . . Brush-Cutting Tools . . . . . . . . . . . . . . . . . . . Chopping Tools . . . . . . . . . . . . . . . . . . . . . . Climbing Tools . . . . . . . . . . . . . . . . . . . . . . . Digging Tools . . . . . . . . . . . . . . . . . . . . . . . . Electrical Power Tools . . . . . . . . . . . . . . . . Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hammers, Mallets, and Mauls . . . . . . . . . . Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Knives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mattocks . . . . . . . . . . . . . . . . . . . . . . . . . . . Miscellaneous Tools . . . . . . . . . . . . . . . . . . Planes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Saws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scrapers . . . . . . . . . . . . . . . . . . . . . . . . . . . . Screwdrivers . . . . . . . . . . . . . . . . . . . . . . . . . Shears and Nippers . . . . . . . . . . . . . . . . . . Timber Handling Tools . . . . . . . . . . . . . . . . Wrenches . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Belts and Safety Straps . . . . . . . . . . . Safety Equipment . . . . . . . . . . . . . . . . . . . . . . Ear Protection . . . . . . . . . . . . . . . . . . . . . . . . Eye Protection . . . . . . . . . . . . . . . . . . . . . . . Gloves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Helmets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Belts and Safety Straps . . . . . . . . . Safety Shoes . . . . . . . . . . . . . . . . . . . . . . . . Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Tools . . . . . . . . . . . . . . . . . . . . . . . . . Safety Strap . . . . . . . . . . . . . . . . . . . . . . . . . . . Saws . . . . . . . . . . . . . . . . . . . . . . . . . . . Backsaw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric Chain . . . . . . . . . . . . . . . . . . . . . . . . Hacksaw . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1 8-2 8-2 8-2
3-1 6-5 7-6 3-3 3-1 7-4 6-4 7-5 39-1 39-3 39-2 39-3 39-2 39-2 9-2 28-6 21-13 15-1 15-4 15-3 15-3
2-1 42-2 32-4 47-2 45-3 49-2 51-3 52-4 2-3 28-3 21-8 20-4 34-3 43-2 53-4 50-2 46-4 30-3 22-5 37-3 48-2 25-13 49-2 2-4 2-3 2-4 2-4 2-4 2-4 2-4 2-3 2-1 2-1 2-3 49-2 46-1 46-3 46-4 52-4 46-4
Index 5
TM 9-243
Handsaw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-2 Keyhole . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-3 Nested . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-3 One-Man Crosscut . . . . . . . . . . . . . . . . . . . . 46-2 Portable Electric Circular . . . . . . . . . . . . . . . 52-4 Two-Man Crosscut . . . . . . . . . . . . . . . . . . . . 46-3 Scrapers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-1 Bearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-2 Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-2 Carbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-2 Flat Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30-2 Triangular Blade . . . . . . . . . . . . . . . . . . . . . . . 30-2 Screwdrivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-1 Clutch Head . . . . . . . . . . . . . . . . . . . . . . . . . . 22-3 Common . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-2 Cross-Point . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-3 Cross-Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-3 Flexible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-4 Jewelers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-4 Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-3 Radio and Pocket . . . . . . . . . . . . . . . . . . . . . 22-5 Ratchet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-4 Screwdriver Bits . . . . . . . . . . . . . . . . . . . . . . . 22-4 Screw Starter or Gimlet . . . . . . . . . . . . . . . . 22-5 Screw and Tap Extractors . . . . . . . . . . . . . . . . 24-1 Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2 Tap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-2 Scriber, Machinist . . . . . . . . . . . . . . . . . . . . . . . 12-2 Selecting the Proper Micrometer . . . . . . . . . . 7-2 Setting, Hammer . . . . . . . . . . . . . . . . . . . . . . . . 21-5 Shears and Nippers . . . . . . . . . . . . . . . . . . . . . 37-1 Cutting Nippers . . . . . . . . . . . . . . . . . . . . . . . 37-3 Hand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-2 Metal Shearing Machine . . . . . . . . . . . . . . . . 37-2 Nippers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-2 Tinners Bench . . . . . . . . . . . . . . . . . . . . . . . . 37-2 Shovels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-1 D-Handled . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-2 Long-Handled . . . . . . . . . . . . . . . . . . . . . . . . . 51-2 Spade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51-2 Spring Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Squares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1 Bevel Protractor . . . . . . . . . . . . . . . . . . . . . . . 13-4 Carpenters . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2 Combination . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3 Sliding T-Bevel . . . . . . . . . . . . . . . . . . . . . . . . 13-4 Try . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3
Steel Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stones, Sharpening . . . . . . . . . . . . . . . . . . . . . Surface, Depth, and Height Gages . . . . . . . . Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Micrometer Depth . . . . . . . . . . . . . . . . . . . . . Rule Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Surface Plate . . . . . . . . . . . . . . . . . . . . . . . . . Vernier Depth . . . . . . . . . . . . . . . . . . . . . . . . . T Taps and Dies . . . . . . . . . . . . . . . . . . . . . . . . . . Boiler Hand Taps . . . . . . . . . . . . . . . . . . . . . . Bottoming Hand . . . . . . . . . . . . . . . . . . . . . . . Mud Hand Taps (Washout Taps) . . . . . . . . Plug/Pipe Hand Tap . . . . . . . . . . . . . . . . . . . . Rethreading Die . . . . . . . . . . . . . . . . . . . . . . . Round Split Adjustable Die . . . . . . . . . . . . . Staybolt Taps . . . . . . . . . . . . . . . . . . . . . . . . . . Taper (Starting) Hand Tap . . . . . . . . . . . . . . Taps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thread Cutting Set . . . . . . . . . . . . . . . . . . . . Two-Piece Collet Die . . . . . . . . . . . . . . . . . . Tension Puller . . . . . . . . . . . . . . . . . . . . . . . . . . Timber Handling Tools . . . . . . . . . . . . . . . . . . . Peavy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timber Carrier . . . . . . . . . . . . . . . . . . . . . . . . Timber Wedges . . . . . . . . . . . . . . . . . . . . . . . . . Tool Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool, Flaring . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool Habits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trammels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trowels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tube Cutting and Flaring Tools . . . . . . . . . . . Flaring Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . Tube Cutters . . . . . . . . . . . . . . . . . . . . . . . . . . U
8-2 29-3 14-1 14-3 14-2 14-2 14-2 14-3 14-3
38-1 38-2 38-2 38-3 38-2 38-3 38-4 38-3 38-2 38-2 38-4 38-3 53-3 48-1 48-2 48-2 45-3 4-1 36-2 2-1 6-4 53-1 53-2 53-2 36-1 36-2 36-2
Using Adjustable Open-End Wrench . . . . . . . . . . . 25-15 Adjustable Snap Gage . . . . . . . . . . . . . . . . . 15-5 Adjustable Strap Pipe Wrench . . . . . . . . . . 25-15
Index 6
Change 1
TM 9-243
Adz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alignment Punch . . . . . . . . . . . . . . . . . . . . . Bearing Scraper . . . . . . . . . . . . . . . . . . . . . . Bell Base Screw Jack . . . . . . . . . . . . . . . . . Bench Grinder . . . . . . . . . . . . . . . . . . . . . . . Bench Plane . . . . . . . . . . . . . . . . . . . . . . . . . Bit Brace Circle Gasket Cutter . . . . . . . . . Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block Plane . . . . . . . . . . . . . . . . . . . . . . . . . . Box Wrench . . . . . . . . . . . . . . . . . . . . . . . . . Brace Drill . . . . . . . . . . . . . . . . . . . . . . . . . . . Brick Trowel . . . . . . . . . . . . . . . . . . . . . . . . . Brush Hook . . . . . . . . . . . . . . . . . . . . . . . . . . C-Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . Cable Jaw Grip and Tension Puller . . . . . Carpenters Hammer . . . . . . . . . . . . . . . . . . Carpenters Square . . . . . . . . . . . . . . . . . . . . Center Cut Cutters . . . . . . . . . . . . . . . . . . . Center Gage . . . . . . . . . . . . . . . . . . . . . . . . . Center Punch . . . . . . . . . . . . . . . . . . . . . . . . Circle Gasket Cutter . . . . . . . . . . . . . . . . . . Climbing Tools . . . . . . . . . . . . . . . . . . . . . . . Combination Bar . . . . . . . . . . . . . . . . . . . . . Combination Square . . . . . . . . . . . . . . . . . . Crosscut Saw . . . . . . . . . . . . . . . . . . . . . . . . . Cutting Nippers . . . . . . . . . . . . . . . . . . . . . . Diagonal Cutting Pliers . . . . . . . . . . . . . . . . . Die and Die Stock . . . . . . . . . . . . . . . . . . . . Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Drift Punch . . . . . . . . . . . . . . . . . . . . . . . . . . Drill Gage . . . . . . . . . . . . . . . . . . . . . . . . . . . Drill Point Gage . . . . . . . . . . . . . . . . . . . . . . Electric Chain Saw . . . . . . . . . . . . . . . . . . . . Electrical Conduit Hand Bender . . . . . . . . Expansive Bit . . . . . . . . . . . . . . . . . . . . . . . . File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fillet and Radius Gage . . . . . . . . . . . . . . . . Flaring Tool . . . . . . . . . . . . . . . . . . . . . . . . . . Gage Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . Gasket Cutter . . . . . . . . . . . . . . . . . . . . . . . . Gear and Bearing Puller . . . . . . . . . . . . . . . Hacksaw . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand Screw Clamp . . . . . . . . . . . . . . . . . . . Hand Tap . . . . . . . . . . . . . . . . . . . . . . . . . . . Height Gage . . . . . . . . . . . . . . . . . . . . . . . . . . Hollow Gasket Cutter . . . . . . . . . . . . . . . . . Impact Wrench . . . . . . . . . . . . . . . . . . . . . . . Inserted Face Hammer . . . . . . . . . . . . . . . . Jewelers Screwdriver . . . . . . . . . . . . . . . . .
45-5 27-6 30-3 20-5 29-3 50-3 44-3 53-6 50-3 25-14 23-3 53-4 47-3 19-2 53-6 21-10 13-4 32-4 16-6 27-4 44-3 49-3 42-3 13-6 46-5 37-3 17-4 38-5 5-3 27-5 16-8 16-8 52-10 40-4 23-4 28-4 16-7 36-2 15-8 44-3 41-4 46-6 19-3 38-4 14-4 44-3 52-7 21-11 22-8
Keyhole Saw . . . . . . . . . . . . . . . . . . . . . . . . . Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Linemans Side Cutting Pliers . . . . . . . . . . . Long-Handled Shovel . . . . . . . . . . . . . . . . . Machinists Ball Peen Hammer . . . . . . . . . Machinists Bench Vise . . . . . . . . . . . . . . . . Machinists Cold Chisel . . . . . . . . . . . . . . . Machinists Scriber . . . . . . . . . . . . . . . . . . . . Marking Gages . . . . . . . . . . . . . . . . . . . . . . . . Mattock . . . . . . . . . . . . . . . . . . . . . . . . . . . . Micrometer Depth Gage . . . . . . . . . . . . . . . . Miscellaneous Measuring Tools . . . . . . . . Offset Ratchet Screwdriver . . . . . . . . . . . . Offset Screwdriver . . . . . . . . . . . . . . . . . . . . Peavy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pipe Cutter . . . . . . . . . . . . . . . . . . . . . . . . . . Pipe Threading Set . . . . . . . . . . . . . . . . . . . Pipe Vise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Plumb Bob . . . . . . . . . . . . . . . . . . . . . . . . . . . Portable Electric Circular Saw . . . . . . . . . . Portable Electric Drill . . . . . . . . . . . . . . . . . . Portable Electric Hammer . . . . . . . . . . . . . . Portable Electric Sander . . . . . . . . . . . . . . . Posthole Digger . . . . . . . . . . . . . . . . . . . . . . Power Torque Wrench . . . . . . . . . . . . . . . . Precision Gage Blocks . . . . . . . . . . . . . . . . . Putty Knife . . . . . . . . . . . . . . . . . . . . . . . . . . . Ratchet Lever Jack . . . . . . . . . . . . . . . . . . . Ring Gage . . . . . . . . . . . . . . . . . . . . . . . . . . Rivet Buster Chisel . . . . . . . . . . . . . . . . . . . Rules and Tapes Examples . . . . . . . . . . . Rule Depth Gage . . . . . . . . . . . . . . . . . . . . . Scratch Awl . . . . . . . . . . . . . . . . . . . . . . . . . . Screwdrivers . . . . . . . . . . . . . . . . . . . . . . . . . Screw Pitch Gage . . . . . . . . . . . . . . . . . . . . Sharpening Stone . . . . . . . . . . . . . . . . . . . . Shovel, Long-Handled . . . . . . . . . . . . . . . . Single-Bit Ax . . . . . . . . . . . . . . . . . . . . . . . . . Slide Hammer Puller Set . . . . . . . . . . . . . . Sliding T-Bevel Square . . . . . . . . . . . . . . . . Slip-Joint Pliers . . . . . . . . . . . . . . . . . . . . . . Small Hole Gage . . . . . . . . . . . . . . . . . . . . . Socket Wrench . . . . . . . . . . . . . . . . . . . . . . . Solid Straight-Hole Reamer . . . . . . . . . . . . Spade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Spanner Wrench . . . . . . . . . . . . . . . . . . . . . Spiral Ratchet Screwdriver . . . . . . . . . . . . . . Spiral Tapered Screw Extractor . . . . . . . . Surface Gage . . . . . . . . . . . . . . . . . . . . . . . .
46-6 10-3 17-5 51-3 21-12 18-4 26-4 12-2 16-9 43-2 14-4 9-3 22-7 22-6 48-2 35-2 35-4 18-5 11-3 52-8 52-5 52-6 52-12 51-5 25-16 15-7 34-3 20-6 15-4 26-5 8-3 14-4 31-2 22-5 16-6 29-5 51-3 45-4 41-5 13-5 17-3 16-6 25-14 39-3 51-4 25-18 22-7 24-3 14-4
Index 7
TM 9-243
Subject Page
W
Subject
Telescoping Gage . . . . . . . . . . . . . . . . . . . . Thickness (Feeler) Gage . . . . . . . . . . . . . . Thread Cutting Tool Gage . . . . . . . . . . . . . Timber Carrier . . . . . . . . . . . . . . . . . . . . . . . Timber Handling Tools . . . . . . . . . . . . . . . . Timber Wedge . . . . . . . . . . . . . . . . . . . . . . . Torque Wrench . . . . . . . . . . . . . . . . . . . . . . Try Square . . . . . . . . . . . . . . . . . . . . . . . . . . . Tubing Bender . . . . . . . . . . . . . . . . . . . . . . . Vernier Depth Gage . . . . . . . . . . . . . . . . . . . Wheel Type Glass Cutter . . . . . . . . . . . . . . Wire Gage . . . . . . . . . . . . . . . . . . . . . . . . . . . Woodworkers Chisel . . . . . . . . . . . . . . . . . V V-Block and Clamp . . . . . . . . . . . . . . . . . . . . . Vises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bench and Pipe . . . . . . . . . . . . . . . . . . . . . . Clamp Base Bench . . . . . . . . . . . . . . . . . . . Handsaw Filing . . . . . . . . . . . . . . . . . . . . . . . Machine Table . . . . . . . . . . . . . . . . . . . . . . . . Machinists Bench . . . . . . . . . . . . . . . . . . . . Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Piston Holding . . . . . . . . . . . . . . . . . . . . . . .
16-7 16-5 16-7 48-2 48-2 45-6 25-16 13-5 40-3 14-4 33-2 16-8 26-3
Page
9-2 18-1 18-2 18-2 18-3 18-3 18-2 18-3 18-2 18-3
Wing Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Wire Strippers (Multipurpose) . . . . . . . . . . . . . 17-3 Wrecking Bar . . . . . . . . . . . . . . . . . . . . . . . . . . 42-2 Wrenches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-1 Adjustable Open-End . . . . . . . . . . . . . . . . . 25-10 Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-3 Clamp Pliers . . . . . . . . . . . . . . . . . . . . . . . . . 25-10 Combination . . . . . . . . . . . . . . . . . . . . . . . . . 25-4 Crowfoot . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-9 Electric Impact . . . . . . . . . . . . . . . . . . . . . . . 52-3 Hex Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-9 Monkey and Auto . . . . . . . . . . . . . . . . . . . . . 25-10 Open-End . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-2 Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-11 Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-9 Power Torque . . . . . . . . . . . . . . . . . . . . . . . . 25-12 Special Purpose Socket . . . . . . . . . . . . . . . 25-7 Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-5 Socket Wrench Handles, Extensions and Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-6 Spanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-12 Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-12
Index 8
TM 9-243
By Order of the Secretaries of the Army, the Navy, and the Air Force:
Official: ROBERT M. JOYCE Major General, United States Army The Adjutant General
JOHN A. WICKHAM, JR. General, United States Army Chief of Staff
STEVEN A. WHITE Admiral, United States Navy Chief of Naval Material Command
Official: JAMES P. MULLINS General, USAF, Commander, Air Force Logistics Command
CHARLES A. GABRIEL, General USAF Chief of Staff
H. A. HATCH Lieutenant General, USMC Deputy Chief of Staff for Installation and Logistics
Distribution: Active Army: To be distributed in accordance with DA Form 12-34B requirements for TM 9 Series Ordnance, Tools and Equipment. Marine Corps: MARCORPS CODES E
TM 9-243
THE METRIC SYSTEM AND EQUIVALENTS

LINEAR MEASURE 1 Centimeter = 10 Millimeters = 0.01 Meters = 0.3937 Inches 1 Meter = 100 Centimeters = 1000 Millimeters = 39.37 Inches 1 Kilometer = 1000 Meters = 0.621 Miles WEIGHTS 1 Gram = 0.001 Kilograms = 1000 Milligrams = 0.035 Ounces 1 Kilogram = 1000 Grams = 2.2 Lb 1 Metric Ton = 1000 Kilograms = 1 Megagram = 1.1 Short Tons LIQUID MEASURE 1 Milliliter = 0.001 Liters = 0.0338 Fluid Ounces 1 Liter = 1000 Milliliters = 33.82 Fluid Ounces SQUARE MEASURE 1 Sq Centimeter = 100 Sq Millimeters = 0.155 Sq Inches 1 Sq Meter = 10,000 Sq Centimeters = 10.76 Sq Feet 1 Sq Kilometer = 1,000,000 Sq Meters = 0.386 Sq Miles CUBIC MEASURE 1 Cu Centimeter = 1000 Cu Millimeters = 0.06 Cu Inches 1 Cu Meter = 1,000,000 Cu Centimeters = 35.31 Cu Feet TEMPERATURE 5/9 (F - 32) = C 212 Fahrenheit is equivalent to 100 Celsius 90 Fahrenheit is equivalent to 32.2 Celsius 32 Fahrenheit is equivalent to 0 Celsius 9/5 C + 32 = F
APPROXIMATE CONVERSION FACTORS
Assignment Questions
Information: The text pages that you are to study are provided at the beginning of the assignment questions.
ASSIGNMENT 1
Textbook Assignment: "Introduction," "Safety and Safety Equipment," "Reading Measuring Scales." "Tool Boxes," "Dividers," "Calipers," "Micrometers," "Rules and Tapes," and "Miscellaneous Measuring Tools," chapters 1 through 9, pages 1-1 through 9-3. 1-1. The text for this course provides which of the following information? 1. Information on the use and care of selected hand tools and measuring tools 2. An explanation of the types and uses of a large number of tools 3. A practical application of a selected group of tools, safety requirements. general care, and limited repair 4. All of the above 1-2. In reference to the use and care of hand tools and measuring tools, which of the following statements is/are true? 1. A user must have, choose, and use the correct tools in order to do the work quickly, accurately, and safely 2. Without the proper tools and knowledge of how to use them, the user wastes time, reduces efficiency, and may face injury 3. Both 1 and 2 above 4. Using tools comes naturally to most people, and formal training is not normally needed 1-3. You are using the text for this course and need information about a specific tool or operation. What is the easiest way to find the information? 1. Refer to the alphabetical index at the end of the manual and turn to the pages that apply 2. Flip through the text and look for the appropriate illustrations 3. Refer to the numerical tool index at the front of the text 4. Refer to the tool color coding chart at the end of the text 1 1-6. 1-4. The introduction to each tool chapter in the text provides which of the following information? 1. How to choose and use the tools covered 2. The various types of tools available and an example of their use 3. Instructions on the care of tools and safety precautions 4. All of the above 1-5. What chapter in the text covers Safety and Safety Equipment? 1. 2. 3. 4. One Two Three Four
Who is the most important part of safety procedures? 1. 2. 3. 4. Your immediate supervisor The executive officer The safety officer You
1-7.
Which of the following statements pertaining to tools is NOT true? 1. You should keep an inventory list in your tool box and check it after each job 2. You should use each tool only on the job for which it was designed 3. Damaged tools should be saved because they can sometimes be used for purposes other than for which they were designed 4. A worker's efficiency is often a direct result of the condition of the tools being used
1-8.
Worker's are often judged by the manner in which they handle and care for their tools. Your own efficiency will be improved if you follow which of the following steps? 1. Organize your tools so that those used most frequently can be reached easily without sorting through the entire contents of the tool box 2. Always place the most expensive tools in the bottom of tool box 3. Clean your tools at the end of the week rather than after each job 4. Store your tools on high shelves where the humidity is lower
1-11.
Proper eye protection is of the highest importance for all personnel. Eye protection is necessary because of which of the following hazards? 1. Infrared and ultraviolet radiation 2. Flying objects such as sparks, globules of molten metal, or chipped concrete and wood 3. Both 1 and 2 above 4. Audio vibrations
1-12.
Protective helmets are made from which of the following materials? 1. 2. 3. 4. Polyethylene Polycarbonate Both 1 and 2 above Perineurium
1-9.
When working with power tools, you should follow all EXCEPT which of the' following procedures? 1. Never operate any power equipment unless you are completely familiar with its controls and features 2. Never try to clear a jammed power tool until it is disconnected from the power source 3. Before connecting a power tool to a power source, be sure the tool switch is in the "ON" position 4. Check electrical cables and cords frequently for overheating
1-13.
Regular hard hats must be insulated so that personnel may be protected from voltages up to what maximum amount? 1. 2. 3. 4. 2.200 3,000 5,000 9.000 volts volts volts volts
1-14.
Electrical workers requiring head protection must wear safety helmets which are capable of withstanding what minimum voltage proof-test? 1. 2. 3. 4. 10,000 20,000 30,000 40,000 volts volts volts volts
1-10.
Safety shoes protect and prevent injury or loss of toes. Some safety shoes are designed to limit damage to your toes from falling objects. What is usually placed in such shoes for protection? 1. 2. 3. 4. Nails Rubber Plastic Steel plates
1-15.
Personnel working with electricity are usually required to wear gloves made from which of the following materials? 1. 2. 3. 4. Cloth Leather Nylon Rubber
1-16.
The more common types of rules and tapes are divided in which of the following ways? 1. 2. 3. 4. Fractions, inches, and feet Inches, feet, and yards Feet, yards, and meters Inches, meters, and milliliters
1-23.
Tool boxes are made from which of the following materials? 1. 2. 3. 4. Steel Wood Plastic All of the above
1-24. 1-17. 3/6 can be reduced to which of the following fractions? 1. 2. 3. 4. 1-18. 1/8 1/4 1/2 2/3
Larger tools are generally contained in which of the following types of tool containers? 1. Mechanic's tool box (chest type) 2. Portable-carpenter's tool box 3. Cantilevered-tray tool box 4. Canvas too bag
Common tapes and rules usually are NOT graduated smaller than what fraction of an inch? 1. 2. 3. 4. 1/2 1/4 1/8 1/16 inch inch inch inch
1-25.
Dividers are used for which of the following purposes? 1. Spreading metal parts 2. Measuring distances between two points 3. Scribing an arc, radius, or circle 4. Both 2 and 3 above
1-19.
If 1/4 equals 16/64, what does 3/4 equal in sixty fourths? 1. 2. 3. 4. 12/64 24/64 48/64 56/64 1-26.
Spring dividers are available in which of the following lengths? 1. 2. 3. 4. 2 2 3 4 t o 4 inches t o 6 inches t o 10 inches t o 15 inches
1-20.
The metric system is based upon what multiples? 1. 2. 3. 4. Multiples Multiples Multiples Multiples of of of of 10 20 30 40 1-27.
Wing-type dividers are available in which of the following lengths? 1. 2. 3. 4. 6, 3, 5, 7, 8, 4, 9. 9, and and and and 12-inch lengths 10-inch lengths 11-inch lengths 13-inch lengths
1-21.
How many millimeters are in a centimeter? 1. 2. 3. 4. 10 20 30 40 millimeters millimeters millimeters millimeters 1-28.
Calipers are used for what purpose? 1. 2. 3. 4. To To To To fasten metal parts light torches measure diameters make bolt threads
1-22.
How many centimeters are in a meter? 1. 2. 3. 4. 100 200 300 400 centimeters centimeters centimeters centimeters 3
1-29.
Transfer calipers are used for what purpose? 1. Threading wire through a bulkhead 2. Holding glued parts together 3. Weighing nuts and bolts 4. Measuring chamfered grooves or flanges
1-35.
On a vernier caliper, the vernier scale is divided into what number of parts? 1. 2. 3. 4. 10 20 25 40
1-36. 1-30. What type of caliper is used for finding shaft centers or locating shoulders? 1. 2. 3. 4. 1-31. A slide caliper A vernier caliper A hermaphrodite caliper An outside caliper 1-37.
On a vernier caliper, what is the difference between the width of one of the 25 spaces on the vernier scale and one of the 24 spaces on the steel rule? 1. 2. 3. 4. 1/1000 2/1000 3/1000 4/1000 of of of of an an an an inch inch inch inch
Slide calipers can be used for which of the following purposes? 1. 2. 3. 4. Finding shaft centers Measuring outside dimensions Measuring inside dimensions Both 2 and 3 above
On a 24-inch or 600-mm caliper, what does .300 inch equal in metric measure? 1. 2. 3. 4. 1.22 2.44 5.66 7.62 mm nun nun mm
1-32.
Which of the following types of calipers contain a straight measuring rule? 1. 2. 3. 4. Transfer calipers Slide calipers Hermaphrodite calipers Spring-joint calipers
1-38.
Standard micrometers are designed to measure distances to what nearest accuracy? 1. 2. 3. 4. .001 .002 .003 .004 of of of of an an an an inch inch inch inch
1-33.
Which of the following instruments can be used to measure distances beyond the range of calipers? 1. 2. 3. 4. Trammels Pullers Planes Taps
1-39.
Which of the following types of micrometers is/are commonly used? 1. 2. 3. 4. The The The All outside micrometer inside micrometer depth micrometer of the above
1-34.
To read a vernier caliper, you must be able to understand which of the following scales? 1. 2. 3. 4. Steel rule Vernier Both 1 and 2 above British thermal unit
1-40.
What is the range of an inside micrometer when used with a 1/2-inch spacer? 1. 2. 3. 4. .500 .200 .300 .400 of of of of an an an an inch inch inch inch
1-41.
The types of micrometers commonly used are designed so that the longest movement possible between the spindle and the anvil is what distance? 1. 2. 3. 4. 1 2 3 4 inch inches inches Inches
1-46.
What does the size of a micrometer indicate? 1. The size of the largest work it will measure 2. The size of the smallest work it will measure 3. The total length of the micrometer 4. The total width of the micrometer
1-42.
The longest movement possible between the spindle and the anvil of a micrometer is known by which of the following terms? 1. 2. 3. 4. Depth Range Height Width
1-47.
A standard micrometer screw has what number of threads per inch? 1. 2. 3. 4. 10 20 30 40
1-48. 1-43. The frames of micrometers are available up to what maximum size? 1. 2. 3. 4. 1-44. 10 15 24 46 Inches inches inches inches 1-49.
On a standard micrometer, one complete revolution of the micrometer screw will move the spindle what distance? 1. 2. 3. 4. .015 .025 .125 .225 inch inch inch inch
A 6-inch micrometer will measure work between which of the following sizes? 1. 2. 3. 4. From 1 From 4 Between Between to to 1 5 6 inches thick 6 inches thick and 6 inches thick and 6 inches thick
Vernier micrometers are designed to measure distances to what nearest accuracy? 1. 2. 3. 4. .0001 .0010 .0100 .1000 of of of of an an an an inch inch inch inch
1-45.
To measure a piece of stock that is approximately 3 1/4 inches, you will need a micrometer with what range? 1. 2. 3. 4. 1234to to to to 2-inch 3-inch 4-inch 5-inch range range range range
1-50.
On a vernier micrometer, the ten spaces on the vernier are equivalent to what number of spaces on the thimble? 1. 2. 3. 4. Five Seven Nine Twelve
1-51.
On a metric micrometer, one revolution of the spindle advances or withdraws the screw what distance? 1. 2. 3. 4. 1.5 1.0 0.5 0.1 mm mm mm mm
1-52.
On a metric micrometer, how many revolutions of the spindle is required to move the barrel 1 mm? 1. One 2. Two 3. Three 4. Four
1-56.
Which of the following tools should be used for grinding, milling, or drilling purposes? 1. 2. 3. 4. Angle plates Registering speed indicators V-blocks and clamps Adjustable parallels
1-53.
In reference to micrometers in general, which of the following statements is true? 1. Micrometers should be coated with a light coat of oil to prevent rust 2. All micrometers should be kept in a single container to save storage space 3. The graduations on micrometers should be painted so they can be easily read 4. Micrometers should be stored in areas where the humidity is very high to prevent rust
1-57.
Angle plates are used for which of the following purposes? 1. As gages for leveling and setup work 2. For clamping or holding work vertically 3. For grinding, milling, or drilling purposes 4. To count the number of revolutions of wheels
1-58.
Registering speed indicators are used for which of the following purposes? 1. To count the number of revolutions of shafts 2. To regulate the flow of fluid 3. To govern the speed of vehicles 4. To register the speed of light
1-54.
Which of the following is the most common measuring tool? 1. 2. 3. 4. A A A A micrometer rule plumb bob level
1-59.
A magnetic base indicator assembly is attached to the work surface in what manner? 1. 2. 3. 4. Bolted Glued Welded Magnetically
1-55.
Which of the following tools should be used as gages for leveling and setup work? 1. 2. 3. 4. Angle plates Registering speed indicators V-blocks and clamps Adjustable parallels
1-60.
Adjustable parallels consist of what number of tapered parts? 1. One 2. Two 3. Three 4. Four
ASSIGNMENT 2
Textbook Assignment: "Levels," "Plumb Bulbs," "Scribers," "Squares," "Surface, Depth, and Height Gages," "Ring and Snap Gages and Gage Blocks," "Miscellaneous Measuring Gages," "Pliers and Tongs," and "Vises," chapters 10 through 18, pages 10-1 through 18-5. 2-5. Which of the following levels is used to span existing cabling, piping, or similar obstructions? 1. 2. 3. 4. 2-6. The The The The master precision level iron bench level striding level machinist's level
2-1.
Levels are designed for which of the following purposes? 1. To prove whether a plane is in the true vertical or true horizontal 2. To prove whether a surface is in the true vertical or true horizontal 3. Both land 2 above 4. To remove the rough spots on surfaces
2-2.
Which of the following types of levels is used mostly in the construction industry? 1. 2. 3. 4. The The The The machinist's level line level iron bench level striding level
The carpenter's level has three vials. One vial is mounted vertically and another is mounted horizontally. The third vial is mounted at what angle? 1. 2. 3. 4. 35 45 55 90 degrees degrees degrees degrees
2-7.
A plumb bob is used for which of the following purposes? 1. To establish a true vertical transfer and line-up reference point 2. To take readings or soundings in tanks or voids 3. Both 2 and 3 above 4. To measure the distance between two horizontal points
2-3.
What feature on a machinist's level increases its accuracy and sensitivity? 1. 2. 3. 4. Its Its Its Its metallic coating extra large vial grooved bottom light weight 2-8.
2-4.
Which of the following levels has a main vial that is used to determine true horizontal, and two smaller vials that are used to determine true vertical? 1. 2. 3. 4. The The The The machinist's level striding level line level master precision level
Plumb bobs are used by which of the following people? 1. 2. 3. 4. Carpenters Surveyors Maintenance technicians All of the above
2-9.
The surveyor's brass plumb bob may be either a spool type or what other type? 1. An adjustable cap type 2. A permanent cap type 3. A flexible cap type 4. A reverse cap type
2-10.
The surveyors brass plumb bob comes with what minimum length of nylon, silk, or linen cord? 1. 2. 3. 4. 2 4 7 9 feet feet feet feet
2-15.
What are the two basic types of machinists scribers? 1. Single point pocket and bent point-straight point 2. Straight point and bent point 3. Rigid point and flexible point 4. Hard point and soft point
2-11.
The surveyors brass plumb bob comes in which of the following sizes? 1. 2. 3. 4. 2, 3, 1, 6, 4, 6, 5, 7, 4. 8, 8, 10, and 8 and 9 and 9 and 16 ounce ounce ounce ounce sizes sizes sizes sizes
2-16.
The points on machinists scribers can be protected in which of the following ways? 1. By reversing them in the handle 2. By placing cork over the points 3. By placing soft wood over the points 4. All of the above
2-12.
Heavier plumb bobs are better for use in which of the following areas? 1. 2. 3. 4. Windy areas Sandy areas Cold areas Hot areas
2-17.
The carpenters square is made up of which of the following parts? 1. 2. 3. 4. The The The The edge and skirt blade and tongue tongue and joint skirt and tongue
2-13.
In reference to the solid steel plumb bob, which of the following statements is true? 1. It comes in 1, 3, and 10 ounce sizes 2. The cord must be obtained from a separate source 3. The cord comes with the plumb bob 4. It is used when extreme accuracy is required
2-18.
What part of a carpenters square is used to compute the number of board feet in a given piece of lumber? 1. 2. 3. 4. The brace measure The rafter table The essex board measure The octagon or eight square scale
2-19.
2-14.
In reference to plumb bobs, which of the following statements is true? 1. Plumb bobs may be used as a lever 2. Plumb bobs should be stored in a humid protective box 3. Plumb bobs should be lightly coated with lubricating oil for long periods of storage 4. Plumb bobs should receive a heavy coat of oil and should be wrapped in oil-soaked paper prior to being stored for long periods of time
What part of a carpenters square is used to find the exact lengths of common braces? 1. 2. 3. 4. The The The The essex board measure brace measure rafter table tongue
2-20.
Which of the following tools is used to check lines that are at right angles to each other? 1. 2. 3. 4. A A A A try square flaring tool scriber digging tool
2-21.
A right angle is what number of degrees? 1. 2. 3. 4. 30 60 75 90 degrees degrees degrees degrees
2-26.
Which of the following tools can be used to measure the thickness of paint? 1. 2. 3. 4. A A A A dial depth gage rule depth gage machinist's level master precision level
2-22.
Which of the following tools is used for testing bevels and laying out angles? 1. 2. 3. 4. A A A A plumb bob climbing tool mattocks T-bevel
2-27.
Height gages are normally graduated in which of the following divisions? 1. 2. 3. 4. .015 .025 .500 .750 inch inch inch inch
2-23.
To transfer measurements to work and to indicate the parallelism of surfaces, you should use which of the following tools? 1. 2. 3. 4. A A A A dial depth gage vernier depth gage surface gage micrometer depth gage
2-28.
In reference to a surface plate, which of the following statements is/are true? 1. A surface plate provides a true, smooth, plane surface 2. A surface plate is often used as a level base for surface and height gages from which to make accurate measurements 3. A surface plate is usually made of close grained cast iron and is rectangular in shape 4. All of the above
2-24.
Which of the following tools is used to measure the depth of holes, slots, counterbores, and recesses? 1. 2. 3. 4. A snap gage A telescoping gage A two-piece collet die A rule depth gage 2-29.
In reference to ring gages, which of the following statements is true? 1. GO gages are larger than NO GO gages 2. GO gages are smaller than NO gages 3. GO and NO GO gages cannot be distinguished from each other 4. GO gages and NO Go gages are always the same size
2-25.
In reference to a vernier depth gage, which of the following statements is/are true? 1. It consists of a graduated scale that is either 6 or 12 inches long 2. It has a sliding head that is designed to bridge holes and slots 3. It cannot enter holes less than 1/4 inch in diameter 4. All of the above
2-30.
Which of the following gage classes indicates that the gage is precision lapped to close tolerances? 1. 2. 3. 4. Class Class Class Class Y X Z ZZ
2-31.
Which of the following gage classes is used only with ring gages? 1. 2. 3. 4. Class Class Class Class ZZ Y Z X
2-36.
Ordinary changes in temperature have a sizable effect on measurements made with precision gage blocks. What is the standard measuring temperature? 1. 2. 3. 4. 50 68 68 72 degrees degrees degrees degrees Fahrenheit Fahrenheit centigrade centigrade
2-32.
The plain snap gage is made in two general types. What are the types? 1. 2. 3. 4. Flat and round Square and round Adjustable and nonadjustable Fixed and flexible
2-37.
You should NOT leave gage blocks wrung together for long periods of time for which of the following reasons? 1. The surfaces will warp 2. The surfaces will turn blue 3. The surfaces will tend to corrode 4. The ends will become unbalanced
2-33.
Before an adjustable snap gage can be used, which of the following procedures must be accomplished? 1. The gage must be heated to a predetermined temperature 2. The GO and NO GO buttons, pins, or anvils must be set to the proper dimensions 3. The gage must be cooled to below freezing 4. The locking screw and the adjusting screws must be removed 2-38.
When using gage blocks, you must consider the source of error resulting from which of the following conditions? 1. 2. 3. 4. Temperature Humidity Light Time
2-39. 2-34. Before using gage blocks, you should take which of the following actions? 1. Remove the coat of rust preventive compound from the gage blocks 2. Boil the gage blocks in water 3. Freeze the gage blocks 4. Remove the adjusting screws from the gage blocks 2-40. 2-35. "Building gage blocks" is also known by which of the following terms? 1. 2. 3. 4. Bonding them together Binding them together Wringing them together Bolting them together
Gage blocks are used for which of the following purposes? 1. To test the outside air temperature 2. To determine the humidity in a space 3. To check the accuracy of tools, dies, and fixtures 4. To test the strength of electrical wire Which of the following tools can be used to verify the accuracy and wear of ring and snap gages? 1. 2. 3. 4. Gage blocks Climbing tools Awls Scribers
10
2-41.
You should NEVER touch the measuring surfaces of gage blocks any more than necessary. The moisture from your hands contains an acid that can cause which of the following problems? 1. The gage blocks to warp 2. The gage blocks to stain 3. The gage blocks to attract an electrical charge 4. The gage blocks to become brittle
2-46.
The pitch of a screw thread is the distance between the center of one tooth to the 1. 2. 3. 4. end of the screw center of the next tooth center of the screw head head of the screw
2-47.
Telescoping gages are used for which of the following purposes? 1. 2. 3. 4. To gage larger holes To measure inside distances Both 1 and 2 above To measure the lenses on telescopes
2-42.
After cleaning gage blocks, you should always take which of the following actions? 1. Coat the gage blocks with heavy grease 2. Boil the gage blocks in gasoline 3. Cover the gage blocks with a film of acid-free oil 4. Paint the gage blocks with lead-free paint 2-48.
Telescoping gages normally have what maximum measuring capacity? 1. 2. 3. 4. 3 6 8 9 inches inches inches inches
2-49. 2-43. Thickness gages are often referred to by which of the following terms? 1. 2. 3. 4. 2-44. Width Height Length Feeler gages gages gages gages 2-50. Center gages are graduated in which of the following increments? 1. 14ths, of an 2. 15ths, of an 3. 17ths, of an 4. 19ths, of an 2-45. 20ths, inch 22nds. inch 28ths, inch 25ths, inch 24ths, and 32nds 26ths, and 34ths 30ths, and 36ths 2-51. 29ths, and 37ths
On a thread cutting tool gage, what do the numbers represent? 1. The number of threads 2. The number of threads 3. The number of threads screw or bolt 4. The length of a screw per inch per foot on a or bolt
Each blade of a fillet and radius gage is normally marked in which of the following increments? 1. 2. 3. 4. 10ths 32nds 42nds 64ths
Which of the following tools is used to check the accuracy of drill cutting edges after grinding? 1. 2. 3. 4. A A A A marking gage thickness gage drill point gage rule depth gage
You can use a screw pitch gage to check the pitch of which of the following types of threads? 1. 2. 3. 4. U. S. Standard and Metric National Form and V-form Whitworth cut All of the above
11
2-52.
A wire gage is normally what shape? 1. 2. 3. 4. Square Triangular Circular Rectangular
2-57.
Which of the following types of pliers is used only for cutting? 1. 2. 3. 4. Diagonal Slip-joint Round-nose Flat-nose
2-53.
Drill gages have a series of holes. The holes are marked in which of the following ways? 1. 2. 3. 4. Letters Fractions Numbers All of the above
2-58.
The piston holding vise is a special purpose vise which can hold engine pistons up to and including what maximum diameter? 1. 2. 3. 4. 3 5 7 9 1/2 1/2 2/3 3/8 inches inches inches inches
2-54.
Marking gages are normally made from which of the following materials? 1. 2. 3. 4. Copper or tin Wood or steel Plastic or glass Paper or plastic
2-59.
The pin vise is a special purpose vise which has a knurled metal handle and a chuck. It is designed to hold material from 0 to what maximum diameter? 1. 2. 3. 4. 0.187 0.397 3.254 8.134 inch inch inches inches
2-55.
Which of the following tools can be used to check the piston ring gap clearance in a cylinder bore? 2-60. 1. 2. 3. 4. A thickness gage A marking gage A wire gage An awl
The handsaw filing vise is a special purpose vise used for holding handsaws while they are being sharpened. It has jaws that are normally between 9 1/2 and what maximum number of inches? 1. 5 inches 2. 7 inches 3. 11 inches 4. 32 inches
2-56.
Which of the following types of pliers can be used to cut small materials such as wire and cotter pins? 1. 2. 3. 4. Parallel jaw Flat-nose Slip-joint Diagonal cutting
12
ASSIGNMENT 3
Textbook Assignment: "Clamps," "Jacks," Hammers, Mallets, and Mauls," "Screwdrivers," "Manual Drills," "Screw and Tap Extractors," "Wrenches," "Chisels," and "Punches," chapters 19 through 27, pages 19-1 through 27-6. 3-5. Which of the following types of hammers is used for driving and pulling nails? 1. 2. 3. 4. 3-6. 3-2. In reference to hand screw clamps, which of the following statements is true? 1. A hand screw clamp usually is made up of three jaws 2. A hand screw clamp should be tightened with a wrench or bar 3. A hand screw clamp is used for holding wood while gluing 4. A hand screw clamp is available in one size only 3-3. Jacks can be used for which of the following purposes? 1. For raising and lowering heavy loads 2. For spreading and clamping operations 3. For pushing and pulling operations 4. All of the above 3-4. Which of the following tools is used for pulling parts together or pushing them apart? 3-9. 1. 2. 3. 4. A reamer A micrometer An outrigger jack A scriber A A A A carpenter's hammer ball peen hammer bumping body hammer cross peen hammer
3-1.
Which of the following tools are used to hold work that cannot be held in a vise, or that has to be held for extended periods of time? 1. 2. 3. 4. C-clamps Chisels Calipers Reamers
Hammers usually come in which of the following sizes? 1. 1, 2, 4, and 6 2. 2, 3, 6, and 9 3. 6, 9, 12, and 15 4. 7, 13, 16, and 20 ounce ounce ounce ounce sizes sizes sizes sizes
3-7.
Which of the following types of hammers is used for forming soft metal, peening rivet heads, and striking metal in out-of-the-way places? 1. 2. 3. 4. A carpenter's hammer A ball peen hammer A claw hammer A club hammer
3-8.
Which of the following tools would normally be used for breaking stones and concrete? 1. 2. 3. 4. A A A A ball peen hammer bumping hammer blacksmith's hammer carpenter's mallet
An inserted soft-faced hammer that is extra hard will be what color? 1. 2. 3. 4. Yellow Green Black Red
13
3-10.
Which of the following tools is used to form and shape sheet metal? 1. 2. 3. 4. A A A A carpenter's hammer tinner's mallet jeweler's hammer mason's hammer
3-16.
Which of the following tools is used to make a pilot hole in wood for wood screws? 1. 2. 3. 4. A A A A cross-point screwdriver flexible screwdriver screw starter or gimlet two-piece collet die
3-11.
A trimmer's hammer has a round flat face on one end of the head. What type of face is on the other end of the head? 1. 2. 3. 4. A A A A square flat face round pointed face tapered chisel face curved claw face
3-17.
Which of the following types of drills is made up of a head, crank, crank handle, ratchet mechanism, and chuck? 1. 2. 3. 4. A hand drill A breast drill A brace drill An electric drill
3-12.
What are the four basic types of dead blow hammers currently in use? 1. Standard head, slimline head, sledge, and ball peen 2. Round head, streamline neck, curved back, and rivet face 3. Huge, large, medium, and small 4. Ball peen, curved back, rivet face, and round head
3-18.
Which of the following tools are used to remove broken screws without damaging the threads or surrounding material? 1. 2. 3. 4. Screw extractors Plumb bobs Chisels Scribers
3-13.
Which of the following types of mallets is made by tightly wrapping and staking a sheet of leather? 1. 2. 3. 4. A A A A carpenter's mallet rubber mallet tinner's mallet rawhide mallet
3-19.
Which of the following types of wrenches has a long smooth shank providing the user with a better gripping surface and is used to reach behind or below blind surfaces? 1. 2. 3. 4. A box wrench A plug wrench A torque wrench An engineer's single open-end wrench
3-14.
Cross-point screwdrivers normally come in which of the following sizes? 1. 2. 3. 4. 2 3 4 9 t o 4 inch t o 8 inch t o 12 inch t o 16 inch sizes sizes sizes sizes 3-20.
Box wrenches surround the nuts. bolt heads, or studs on all sides. They are available with which of the following point openings? 1. 6-point openings 2. 12-point openings 3. Both 1 and 2 above 4. 29-point openings
3-15.
Which of the following types of screwdrivers should you use to drive or remove screws that cannot be lined up straight with common screwdrivers, or are located in tight corners? 1. 2. 3. 4. Cross-point Cross-tip Ratchet Offset 14
3-21.
In reference to ignition wrenches. which of the following statements is true? 1. Ignition wrenches are usually very large in size 2. Ignition wrenches usually have the same size jaw opening on both ends 3. Ignition wrenches are usually used to remove lug nuts from wheels of vehicles 4. Ignition wrenches are usually offset 10 degrees on each end
3-26.
Which of the following types of wrenches does NOT have to be lifted up and repositioned each time the shank has reached its maximum travel between two obstructions? 1. An engineer's single open-end wrench 2. A ratchet-box wrench 3. An ignition wrench 4. A combination wrench
3-27.
In reference to socket wrenches, which of the following statements is/are true? 1. A socket wrench consists of a square metal sleeve with a round opening in one end for insertion of a handle 2. The length of a socket determines its size 3. The drive end of a socket may vary in size from 1/4 to 1 inch 4. All of the above
3-22.
Which of the following types of wrenches combines the open-end jaw with a long tapered shank providing a wrench/alignment punch combination? 1. 2. 3. 4. A construction wrench An ignition wrench An open end wrench A box wrench 3-28.
3-23.
Wrenches are usually made from which of the following materials? 1. 2. 3. 4. Plastic Copper Tin Steel alloy
Which of the following tools is used when it is necessary to reach around an object? 1. 2. 3. 4. A A A A universal joint socket plumb bob micrometer bevel protractor
3-24.
Which of the following types of wrenches is used in the building trades and on heavy objects that require alignment before fastening? 1. An open-end wrench 2. A box wrench 3. A combination wrench 4. A construction wrench In reference to box wrenches, which of the following statements is/are true? 1. Box wrenches are offset from the shank by 15 degrees 2. The 12-point opening on a box wrench may be used on both square and hexagonal bolt heads 3. The length of a box wrench depends upon the size of their opening 4. All of the above
3-29.
Which of the following tools is used for increased leverage or for working around other objects? 1. 2. 3. 4. A A A A ratcheting adapter sliding T-Bar handle crowfoot wrench wedge-type stud remover
3-25.
3-30.
Which of the following tools is used to change the drive size between a socket and a handle? 1. 2. 3. 4. A A A A ratcheting adapter socket wrench adapter sliding T-Bar hinged handle
15
3-31.
Which of the following tools is used to convert a non-ratcheting socket wrench handle into a ratchet drive? 1. 2. 3. 4. A A A A ratcheting adapter socket wrench adapter socket wrench extension sliding T-Bar handle
3-37.
Which of the following tools should be used to remove nuts and bolts 'that have been rounded off by someone using the wrong size wrench? 1. 2. 3. 4. A box wrench Clamp pliers A torque wrench Wire cutters
3-32.
Which of the following tools is usually used to remove or install vehicle wheel stud nuts? 1. 2. 3. 4. A sliding T-Bar handle A combination wrench A four-way socket wrench An open-end wrench
3-38.
Which of the following tools should NOT be used to install new nuts or bolts? 1. 2. 3. 4. A combination wrench A box wrench Clamp pliers A socket wrench
3-33.
In reference to stud removers, which of the following statements is true? Some stud removers can be adjusted to remove different size studs 2. Most stud removers are electrically driven 3. There is only one type of stud remover 4. Stud removers are usually used to remove tiny screws from sensitive instruments 1.
3-39.
Which of the following tools is designed to measure the specific degree of tightness of nuts or bolts? 1. 2. 3. 4. A torque wrench An open end wrench A pipe wrench A reamer
3-40.
3-34.
Hex key wrenches are usually what shape? 1. 2. 3. 4. T-shaped Circular-shaped Square-shaped L-shaped
The stillson wrench, the strap wrench, and the chain wrench come under what general category of wrenches? 1. Combination wrench 2. Torque wrench 3. Pipe wrench 4. Box wrench Which of the following wrenches are similar? 1. 2. 3. 4. Torque and pipe wrenches Monkey and auto wrenches Strap and spanner wrenches crowfoot and plug wrenches
3-41.
3-35.
Plug wrenches usually come in which of the following types? 1. 2. 3. 4. Bar-type Socket-type Multiple plug wrench All of the above
3-42.
A power torque wrench is operated by the use of what type of power? 1. 2. 3. 4. Hydraulic Electrical Magnetic Manual
3-36.
Which of the following tools is used to remove or install drain plugs? 1. 2. 3. 4. A A A A crowfoot wrench T-Bar handle box wrench plug wrench 16
3 - 4 3 . Which of the following types of wrenches is used to tighten nuts and bolts requiring 200 or more foot pounds of torque? 1. 2. 3. 4. 3-44. A A A A spanner wrench plug wrench box wrench power torque wrench
3-49.
Which of the following tools is a precision instrument? 1. 2. 3. 4. A A A A strap wrench torque wrench bolt cutter box wrench
3-50.
What are the two basic types of spanner wrenches? 1. The hook-type and the pin-type 2. The round-face type and the square-face type 3. The adjustable-type and the fixed-type 4. The flexible-type and the rigid-type
An S-shaped open end wrench is normally offset what number of degrees? 1. 2. 3. 4. 22 15 12 10 1/2 1/4 2/3 3/4 degrees degrees degrees degrees
3-51.
Which of the following tools should you use to cut holes in flat stock and to cut V-groves? 1. 2. 3. 4. A A A A center punch staybolt tap diamond point chisel thread cutting tool
3-45.
The straps on strap pipe wrenches are usually made from which of the following materials? 1. 2. 3. 4. Rubber Canvas Leather Both 2 and 3 above 3-52.
3-46.
Which of the following wrenches has one fixed jaw and one adjustable jaw? 1. 2. 3. 4. An adjustable open-end wrench A multiple plug wrench A combination wrench A box wrench
Which of the following types of chisels has a beveled point on one edge, a flat face on the other end, is 10-1/2 inches long, and weighs 5-1/2 pounds? 1. 2. 3. 4. A A A A rivet buster chisel machinist's chisel track chisel woodworker's chisel
3-53.
3-47.
A wedge-type stud removers is normally made of a socket housing and a total of how many wedges 1. 2. 3. 4. Five Two Three Four
In reference to a woodworker's chisel, which of the following statements is true? 1. Rough cuts should be made with the bevel side up 2. Smooth finishing cuts should be made with the bevel side down 3. Cuts should always be made away from the person doing the cutting 4. Both hands of the person doing the cutting should be in front of the cutting edge at all times
3-48.
Socket wrench extensions usually range from 2 inches to what maximum length? 1. 2. 3. 4. 10 13 17 36 inches inches inches inches
17
3-54.
Woodworker's chisels come in which of the following types? 1. 2. 3. 4. Rivet-buster type Socket-type Tang-type Both 2 and 3 above
3-58.
The tinmen's hollow punch has a solid metal shank terminating in a sharpened, hollowed end. This type of punch is used for which of the following purposes? 1. To remove bolts 2. To mark rivets 3. To punch holes through thin sheet metal 4. To align sections of tin
3-55.
Which of the following tools is used to mark centers on metal or wood without the use of a hammer? 1. 2. 3. 4. A A A A catapunch micrometer gage block gimlet 3-59.
Which of the following tools is used to form the flange on grommets which are installed along the edges of flags, sails. mail bags, and similar items? 1. 2. 3. 4. A A A A catapunch grommet-inserting punch mason's hammer scribber
3-56.
What are the two general types of center punches? 1. 2. 3. 4. Hand-held and automatic Wedge-shape and circular Spindle and bevel Iron and copper
3-60.
3-57.
Which of the following tools is used to mark soft metal? 1. 2. 3. 4. A A A A tinmen's hollow punch prick punch lever punch fillet
Which of the following tools should you use to punch small round holes near the edges of metal or leather material? 1. 2. 3. 4. A A A A lever punch catapunch prick punch reamer
18
ASSIGNMENT 4
Textbook Assignment: " F i l e s , " "Grinders and Sharpening Stones," "Scrapers," "Awls," "Bolt and Cable Cutters," "Glass Cutters," "Knives,' 'Pipe Cutting and Threading Tools," "Tube Cutting and Flaring Tools," 'Shears and Nippers," "Taps and Dies," "Reamers," and "Benders," chapters 28 through 40, pages 28-1 through 40-4. 4-6. Which of the following types of files should you use to file internal angles and to clean out square corners? 1. 2. 3. 4. 4-7. A A A A round file three-square file curved-tooth file mill file
4-1.
The point, edge, face, heel, and tang are the five parts of which of the following tools? 1. 2. 3. 4. A A A A file screwdriver torque wrench machinist's chisel
4-2.
Curved-tooth files are cut in a contour across the face and are used to smooth which of the following surfaces? 1. 2. 3. 4. Aluminum and bronze Lead and babbitt Zinc and plastics All of the above
Which of the following types of files are made to more exact measurements than American files and are used primarily as finishing tools on delicate parts? 1. 2. 3. 4. Three-square files Swiss pattern files Pillar files Round files
4-3.
A file used for heavier work will have which of the following grades of coarseness? 1. 2. 3. 4. Second-cut Smooth-cut Bastard-cut Dead smooth-cut
4-8.
When filing soft metal, you should start with a second-cut file and finish with which of the following files? 1. 2. 3. 4. A smooth-cut file A course double-cut file A bastard-cut file A standard-cut curved-tooth file
4-4.
Which of the following types of files are used to file in slots and keyways? 1. 2. 3. 4. Three-square files Curved-tooth files Pillar files Round files 4-9.
When using a new file, what will happen if you apply too much pressure? 1. The file will become brittle 2. The filing surface will turn blue 3. The teeth on the file will break off 4. The file will become soft
4-5.
Which of the following types of files are used to file rectangular slots and keyways? 1. 2. 3. 4. Curved-tooth files Three-square files Warding files Square files
19
4-10.
When filing brass or bronze, you should start with which of the following files? 1. 2. 3. 4. A A A A second-cut file smooth-cut file course double-cut file bastard-file
4-16.
Which of the following tools are used to punch holes in leather and as an aid during sewing? 1. 2. 3. 4. Round-nose pliers Telescoping gages Saddler's awls Trammels
4-11.
Which of the following tools consists of an abrasive wheel mounted on a rotatable shaft? 1. 2. 3. 4. A A A A rethreading die grinder tap extractor ring gage
4-17.
Which of the following tools should you use to scribe marks or as a center punch on soft wood and plastics? 1. 2. 3. 4. A A A A scratch awl mattock ring gage staybolt tap
4-12.
For reshaping and sharpening chisels, drills, and hatchets, you should use which of the following tools? 1. 2. 3. 4. A bench grinder An iron bench level A jeweler's hammer A two-piece collet die
4-18.
Which of the following tools are considered security items and should be secured when not in use? 1. 2. 3. 4. Open-end wrenches Jeweler's hammers Master precision levels Bolt cutters
4-13.
Before using a bench grinder, you should tap the wheel lightly with a mallet. What is indicated if you get a ringing sound? 1. 2. 3. 4. The The The The wheel is cracked wheel is satisfactory wheel has oil on it wheel is out of alignment
4-19.
In reference to a center cut cutter, which of the following statements is true? 1. The shorter the handle, the greater the cutting capacity 2. The handles range from 3 to 9 inches in length 3. The cutting edges are in the center of the jaw between equal levels 4. It is used to cut hard steel only
4-14.
Which of the following types of scrapers is used to clean cylinder heads? 1. 2. 3. 4. A A A A carbon scraper bearing scraper box scraper triangular blade scraper 4-20.
Which of the following tools are used to cut lead and rubber-covered cable? 1. 2. 3. 4. Machinist's scribers Shear cut cable cutters Mattocks Clamp pliers
4-15.
To scrape stencil markings from wood surfaces, you should use which of the following tools? 1. 2. 3. 4. A A A A bearing scraper bench grinder round file box scraper
20
4-21.
Angular cut cutters have the cutting edges offset what number of degrees from the handles? 1. 2. 3. 4. 10 20 30 40 degrees degrees degrees degrees
4-27.
Pipe cutters can be used to cut which of the following materials? 1. 2. 3. 4. Steel and brass only Copper and wrought iron only Lead only Steel, brass, copper, wrought iron, and lead
4-22.
Shear cut, flat bar, and strip cutters are used to cut which of the following stock? 1. 2. 3. 4. Flat-soft stock Medium-hard bar stock Strip stock All of the above
4-28.
To protect you from getting cut on the sharp ends, pipe often comes with which of the following items? 1. 2. 3. 4. Wooden plugs Rubber plugs Protective caps Plastic inserts
4-23.
Which of the following tools is used to make straight cuts on glass? 1. 2. 3. 4. A A A A circle pillar wheel track glass cutter file glass cutter chisel
4-29.
Threading sets should be stored in which of the following containers? 1. 2. 3. 4. A case A box Either 1 or 2 above A tool box
4-30. 4-24. Which of the following tools is used to cut wallboard, paper, cardboard, linoleum, canvas, and upholstery materials? 1. 2. 3. 4. 4-25. A A A A shop knife saddler's knife scriber scratch awl
Tube cutters are usually designed to cut tubing up to what maximum size? 1. 1 inch 2. 2 5/8 inches 3. 3 1/2 inches 4. 4 inches
4-31.
What are the two basic types of flaring tools? 1. 2. 3. 4. Hard and soft Single and double Long and short Soft and brittle
Which of the following tools should you use to smooth wood after chopping with a hatchet or axe? 1. 2. 3. 4. A A A A putty knife draw knife wooden maul carpenter's hammer
4-32.
Which of the following tools are used to cut wire, light metal bars, bolts, nails, and protruding metal? 1. 2. 3. 4. Cutting nippers Wire strippers Flat-nose pliers Center cut cutters
4-26.
There are two sizes of pipe cutters. One size can cut from 1/8 to 2 inches, while the other can cut from 2 to what maximum number of inches? 1. 2. 3. 4. 8 6 5 4 inches inches inches inches
21
4-33.
Which of the following tools are used to cut heavy sheet metal? 1. 2. 3. 4. Nippers Clamp pliers Slip-joint pliers Tinner's bench shears
4-39.
Dies are used for which of the following purposes? 1. For cutting internal threads 2. For removing paint from metal parts 3. For sealing containers 4. For cutting external threads
4-34.
A metal shearing machine is normally operated by which of the following sources of power? 1. 2. 3. 4. Electrical Hydraulic Foot Magnetic
4-40.
Taps are made from which of the following materials? 1. 2. 3. 4. Hardened steel Plastic Copper Leather
4-35.
The shear blades on metal shearing machines are normally what length? 1. 2. 3. 4. 36 42 51 73 inches inches inches inches
4-41.
Which of the following tools is used to start tapping operations? 1. 2. 3. 4. A A A A taper hand tap rethreading die scratch awl three-square file
4-36.
Metal shearing machines will normally cut iron up to what maximum thickness? 1. 2. 3. 4. 1/2 1/8 1/16 1/32 inch inch inch inch
4-42.
Pipe taps have tapered diameters that increase at what rate? 1. 2. 3. 4. 1/2 3/4 7/8 1 inch inch inch inch per per per per foot foot foot foot
4-43. 4-37. Cutting nippers normally come in what maximum length? 1. 2. 3. 4. 4-38. 10 12 14 15 inches inches inches inches 4-44. Taps are used for which of the following purposes? 1. 2. 3. 4. For cutting external threads For bending or shaping metal For cutting internal threads For removing rust from cylinder heads 4-45.
What are the two types of boiler taps? 1. 2. 3. 4. Bent and straight Straight and tapered Round and square Hard and soft
Straight boiler taps range in size from 1/2 inch to what maximum diameter? 1. 1 1/2 2. 2 3/4 3. 3 1/4 4. 4 3/8 inch inches inches inches
A mud or washout tap has what total number of flutes? 1. 2. 3. 4. Six Eight Ten Twelve
22
4-46.
Which of the following tools are used in boiler, locomotive, and railroad shops for tapping holes in the outer and inner plates of boilers? 1. 2. 3. 4. Breast drills Precision gage blocks Staybolt taps Vernier calipers
4-52.
To enlarge and true a hole, you should use which of the following tools? 1. 2. 3. 4. A A A A scriber vernier caliper reamer jeweler's hammer
4-53.
What are the three parts of a reamer? 1. 2. 3. 4. Body, stem, and flange Body, shank, and blades Blades, flange, and rim Shank, flange, and wheel
4-47.
Rethreading dies are used for which of the following purposes? 1. To start tapping operations 2. To restore bruised or rusty threads on screws and bolts 3. To remove threads from screws and bolts 4. To make threads on the inside of nuts
4-54.
Where can you find the size of a reamer? 1. Stamped on the shank of the tool 2. Stamped between the blades of the tool 3. Painted on the body of the tool 4. Scribed on the body of the tool
4-48.
The two-piece collet die consists of two die sections. What are the two sections called? 1. The collet 2. The collet washer 3. The collet ridge 4. The collet nut and collet bolt screw and collet groove and collet cap and collet guide 4-55.
Solid taper-pin reamers are made with what standard taper? 1. 2. 3. 4. 3/4 1/2 1/4 1/8 inch inch inch inch per per per per foot foot foot foot
4-49.
The mud or washout tap has a total of how many threads per inch? 4-56. 1. 2. 3. 4. 12 15 18 20 threads threads threads threads per per per per inch inch inch inch
An expansion reamer is made from which of the following materials? 1. 2. 3. 4. Plastic Carbon steel Copper Lead
4-50.
Tapered boiler taps have tapered diameters that increase at what rate? 1. 1/8 2. 1/4 3. 1/2 4. 3/4 inch inch inch inch per per per per foot foot foot foot
4-57.
Solid taper-pin reamers come with which of the following types of flutes? 1. Straight flutes only 2. Spiral flutes only 3. Straight and spiral flutes 4. Square flutes
4-51.
Thread cutter sets contain which of the following items? 1. Taps, dies, and diestocks 2. Tap wrenches, guides, and screwdrivers 3. Wrenches for making adjustments 4. All of the above 23
4-58.
Pipe reamers come in which of the following sizes? 1/8-inch to capacity 2. 1/4-inch to capacity 3. 1/4-inch to capacity 4. All of the 1. 1-inch pipe 1 1/4-inch pipe 2-inch pipe above
4-60.
The radius block of a hand tube bender is graduated from 0 to what maximum number of degrees? 1. 2. 3. 4. 120 180 240 370 degrees degrees degrees degrees
4-59.
What are the two types of spring tube benders? 1. 2. 3. 4. External and internal Plastic and steel Round and square Rigid and flexible
24
ASSIGNMENT 5
Textbook Assignment: "Pullers," "Bars," "Mattocks," "Gasket Cutters," "Chopping Tools," "Saws," "Brushcutting Tools," "Timber and Handling Tools." "Climbing Tools," "Planes," "Digging Tools," "Electrical Power Tools," and "Miscellaneous Tools," chapters, 41 through 53. pages 41-1 through 53-7. 5-6. Which of the following pullers has interchangeable jaws? 1. 2. 3. 4. 5-7. The steering gear arm puller The battery terminal and small gear puller Both 1 and 2 above The universal bearing and bushing puller
5-1.
The universal gear puller is usually of yoke and screw construction. The jaws have what diameter capacity? 1. 2. 3. 4. 0 0 5 6 to to to to 10 14 20 18 inches inches inches inches
5-2.
The universal gear puller is used for pulling which of the following items? 1. 2. 3. 4. Gears Pulleys Wheels All of the above
What is the shape of a cotter pin puller? 1. Oval-shaped 2. T-shaped 3. S-shaped 4. Square-shaped
5-8. 5-3. The gear and bearing puller will spread what maximum distance? 1. 2. 3. 4. 5-4. 2 3 5 7 1/2 1/4 1/2 3/8 inches inches inches inches 5-9.
Which of the following tools is used to pull large nails or spikes, to open heavy crates, and to do wrecking work? 1. 2. 3. 4. A A A A crowbar dead blow hammer lever punch wrecking bar
The gear and bearing puller is a screw-type puller with a total of how many jaws? 1. 2. 3. 4. One Two Three Four
A pinch bar is usually used for which of the following purposes? 1. For heavy ripping and prying jobs 2. For light ripping and prying jobs 3. For pulling large nails or spikes 4. For repairing computer components
5-5.
The universal bearing and bushing puller provides a pulling capacity of up to what maximum distance? 1. 2. 3. 4. 1 2 3 4 1/4 1/8 3/4 1/4 inches inches inches inches 5-10.
Bars usually come in which of the following lengths? 1. 2. 3. 4. From From From From 12 14 18 24 to to to to 72 76 80 96 inches inches inches inches
25
5-11.
Which of the following tools is designed for digging and cutting operations? 1. 2. 3. 4. A A A A mattock peavy timber wedge block plane
5-17.
A hollow gasket cutter is also referred to by which of the following terms? 1. 2. 3. 4. A solid punch A square punch A hard punch A hollow punch
5-12.
The single-beveled mattock can be combined with other digging tools to perform a variety of functions. The "pick mattock" is a combination of the single-beveled mattock and what other tool? 1. 2. 3. 4. A shovel A screwdriver A pick A hammer
5-18.
Which of the following types of gasket cutters has a tapered square shank? 1. 2. 3. 4. A compass-style circle gasket cutter A bit brace circle gasket cutter A heavy duty bench mount gasket cutter A hollow gasket cutter
5-13.
The raw wood handles of mattocks should be rubbed thoroughly (preferably prior to use) with a cloth soaked in which of the following liquids? 1. 2. 3. 4. Water Gasoline Alcohol Linseed oil
5-19.
Which of the following tools is used by emergency personnel to gain quick access to an area? 1. 2. 3. 4. An adz A timber wedge A crash ax A nested saw
5-20.
5-14.
On a compass-style circle gasket cutter, what is used to adjust the diameter? 1. 2. 3. 4. A hammer A knurled thumb screw A straight slot screwdriver A round split adjustable die 5-21.
Which of the following tools is used for chopping and smoothing lumber or logs where a great deal of wood or bark is to be removed? 1. 2. 3. 4. An adz A timber wedge A half-hatchet A woodworker's chisel
5-15.
A bit brace circle gasket cutter can be adjusted to what maximum diameter? 1. 2. 3. 4. 1 2 5 9 1/4 1/8 1/2 3/4 inches inches inches inches
Timber wedges are normally made from what material? 1. 2. 3. 4. Plastic Copper Glass Steel
5-22.
What are the two categories of handsaws? 1. 2. 3. 4. Crosscut and nested Keyhole and hacksaw Ripsaw and crosscut Drag and push
5-16.
What is used to adjust the diameter of a bit brace circle gasket cutter? 1. 2. 3. 4. A hex wrench A straight slot screwdriver An open-end wrench A machinist's level 26
5-23.
In reference to handsaws, which of the following statements is/are true? 1. 2. 3. 4. Crosscut saws are designed to cut against the grain Ripsaws are designed to cut with the grain Both 1 and 2 above Crosscut saws consist of a thick blade with a steel handle
5-29.
Which of the following tools is/are used for cutting underbrush, shrubs, tree branches, vines, and tall grass? 1. 2. 3. 4. A nested saw A brush hook A machete Both 2 and 3 above
5-30.
The machete used in the military is normally what size? 1. 2. 3. 4. 10 15 18 30 inches inches inches inches
5-24.
Which of the following saws should you use to cut down a tree? 1. 2. 3. 4. A A A A backsaw one-man crosscut saw keyhole saw nested saw
5-31.
5-25.
When two men are required for extra heavy cutting jobs, which of the following saws should be used? 1. 2. 3. 4. A two-man crosscut saw A backsaw A nested saw A compass saw
For lifting or moving heavy objects such as logs or timbers, you should use which of the following tools? 1. 2. 3. 4. A mattock A timber carrier A peavy Either 2 or 3 above
5-32.
Which of the following tools are used for climbing poles and trees? 1. 2. 3. 4. Safety straps Safety belts Leg irons with spurs All of the above
5-26.
What is the smallest type of nested saw? 1. 2. 3. 4. The backsaw The keyhole saw The handsaw The hacksaw
5-33.
What are the two types of planes most generally used? 1. 2. 3. 4. Block and tackle Block and bench Bench and circular Square and round
5-27.
What types of blades are used on hacksaws? 1. Flexible and soft 2. Hard and rigid 3. Rigid and soft 4. Hard and flexible 5-34. Which of the following saws is designed to cut metal? 1. 2. 3. 4. A A A A hacksaw handsaw one-man crosscut saw two-man crosscut saw
What is the smallest type of plane? 1. Block 2. Tackle 3. Bench 4. Square
5-28.
5-35.
The cutting blade on a jack plane is set at approximately what angle? 1. 2. 3. 4. 15 25 45 90 degrees degrees degrees degrees
27
5-36.
What feature on a block plane is used when additional pressure is needed? 1. 2. 3. 4. A A A A hand hold toe knob pressure lever spring adjustment
5-42.
Which of the following tools should be used to remove nuts, bolts, and screws? 1. 2. 3. 4. A portable electric hammer An electric impact wrench A saddler's awl A sledge hammer
5-37.
When not in use, a plane should be placed in what position? 1. 2. 3. 4. On On On On its its its its side cutting edge handle front end
5-43.
Standard sockets should NOT be used with impact tools for which of the following reasons? 1. 2. 3. 4. The can shatter causing serious injury to personnel They can damage the impact tools Both 2 and 3 above They are too expensive
5-38.
Which of the following tools is used to bore holes in the ground for posts, poles, and explosive charges? 1. 2. 3. 4. A trowel A machete A plumb bob An auger
5-44.
Before drilling a hole, you should make a small prick point in the spot where the hole will be made. Which of the following tools should you use for this purpose? 1. 2. 3. 4. A punch only An awl only A punch or an awl A scriber
5-39.
Which of the following tools is used for heavy digging or in confined areas? 1. 2. 3. 4. A peavy A brush hook A spade An adz 5-45.
You should always wear ear protection when operating which of the following tools? 1. 2. 3. 4. An electric hammer A compass saw A power torque wrench All of the above
5-40.
Basically, what is a portable electric drill? 1. 2. 3. 4. An metal motor in an electric housing A pneumatic motor in a plastic housing A hydraulic motor in a brass housing An electric motor in a metal housing 5-46.
When using a portable electric hammer, which of the following actions should you take to prevent unnecessary wear of the precision parts? 1. 2. 3. 4. Use only light hand pressure Place the bit against the work surface before operating the switch Both 2 and 3 above Place an insulating board between the electric hammer and the work
5-41.
A portable electrical drill can be used for which of the following purposes? 1. 2. 3. 4. Drilling Sanding and sawing Buffing and polishing All of the above
28
5-47.
What type of power is used to drive an electric chain saw? 1. Manual 2. Hydraulic 3. Pneumatic 4. E l e c t r i c
5-51.
Which of the following tools should you use to scoop and spread mortar? 1. 2. 3. 4. A A A A brick trowel cement trowel flat blade scraper triangular blade scraper
5-48.
When using a portable electric circular saw, you must ensure the saw blade is revolving at what speed before it contacts the work surface? 1. 2. 3. 4. 1/4 speed 1/2 speed 3/4 speed Full speed
5-52.
Which of the following tools is used to lift material out of narrow deep holes? 1. 2. 3. 4. A A A A cable jaw grip miner's spoon scriber brush hook
5-53.
5-49.
When operating a portable electric sander, which of the following problems will occur if you use excessive pressure? 1. 2. 3. 4. The sanding action will take longer The disk will clog The motor will overheat All of the above
Which of the following tools is used to tighten or stretch wires or cables? 1. 2. 3. 4. A A A A cable jaw grip trip wire grapnel miner's spoon chain pipe wrench
5-54.
Which of the following items is used for towing vehicles, slinging loads, and hauling objects? 1. 2. 3. 4. A A A A trip wire grapnel cable jaw grip chain assembly tension puller
5-50.
A cement trowel is normally what shape? 1. 2. 3. 4. Rectangular Circular Triangular Square
5-55.
Which of the following tools is used to find booby traps and to detonate mines? 1. 2. 3. 4. A miner's spoon A trip wire grapnel A spade A combination bar
29

Navedtra 14256 PDF

Uploaded by

Copyright:

Available Formats

Navedtra 14256 PDF

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Navedtra 14256 PDF

Uploaded by

Copyright:

Available Formats

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

NONRESIDENT TRAINING COURSE

Tools and Their Uses

DISTRIBUTION STATEMENT A : Approved for public release; distribution is unlimited.

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

DISTRIBUTION STATEMENT A : Approved for public release; distribution is unlimited.

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

NAVSUP Logistics Tracking Number 0504-LP-026-8900

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

INSTRUCTIONS FOR TAKING THE COURSE

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

NETPDTC 1550/41 (Rev 4-00)

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

*TM 9-243 M6290-AJ-MAN-010 TO 32-1-101 TM 10209-10/1

WASHINGTON, DC, 12 December 1983

USE AND CARE OF HAND TOOLS AND MEASURING TOOLS

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

HOW TO USE THIS MANUAL

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

Section I. SAFETY RULES (GENERAL)

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

TOOL HABITS - Continued

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

SAFETY RULES (POWER TOOLS)

Section Ill. SAFETY EQUIPMENT

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

SAFETY EQUIPMENT - Continued

SAFETY BELTS AND SAFETY STRAPS

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

Chapter 3 READING MEASURING SCALES

READING THE SCALE OF A RULE OR TAPE

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

READING THE SCALE OF A RULE OR TAPE - Continued

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

READING THE SCALE OF A RULE OR TAPE - Continued

READING A METRIC RULE

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

Chapter 4 TOOL BOXES

4-2 4-2 4-2 4-2 4-2 4-2 4-2

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

TYPES AND USES

PORTABLE CARPENTERS TOOL BOX

CANTILEVERED TRAY TOOL BOX

MECHANICS TOOL BOX (Chest Type)

REMOVABLE TRAY TOOL BOX

FIVE-DRAWER PORTABLE TOOL BOX

HARDWOOD MACHINISTS TOOL BOX (Chest Type)

CANVAS TOOL BAG

Downloaded from http://www.everyspec.com on 2009-01-12T13:04:08.

5-2 5-2 5-2 5-3 5-3