Temperature Meter

K3MA-L
CSM_K3MA-L_DS_E_6_1

Highly Visible LCD Display with 2-color (Red and Green) LEDs
Wide input range - select from two types of platinum-resistance thermometers and ten types of thermocouples. Front-panel key operation for easy setting. Average processing function suppresses flicker. Temperature input shift and temperature unit selection functions. Easy confirmation of max/min display. Short 80-mm depth (measured from edge of face plate). Finger protective cover (standard equipment) protects against electric shock. Water- and dust-proof NEMA4X (IP66 equivalent) front panel. Recognized to conform to U.S. and Canadian requirements under the Component Recognition Program of UL. CE marking.
Refer to Safety Precautions for All Digital Panel Meters.

Model Number Structure

Model Number Legend
K3MA-L-@
1 2 3
3. Supply Voltage 100-240VAC: 100 to 240 VAC 24VAC/VDC: 24 VAC/VDC 1. Input Type L: Platinum-resistance thermometer or thermocouple 2. Output Type None: No output C: With relay contact output (SPDT)

Ordering Information
List of Models
Input type Platinum-resistance thermometer or thermocouple Supply voltage 100 to 240 VAC 24 VAC/VDC None 1 relay contact output (SPDT) None 1 relay contact output (SPDT) Output Model K3MA-L 100-240VAC K3MA-L-C 100-240VAC K3MA-L 24VAC/VDC K3MA-L-C 24VAC/VDC

Rubber Packing
Model K32-P1

Note: Rubber packing is provided with the Controller.

Accessories (Order Separately)

Name Splash-proof Soft Cover Shape K32-49SC Model

Hard Cover

K32-49HC

K3MA-L

Specifications
Ratings
K3MA-L 100-240VAC, K3MA-L-C 100-240VAC Supply voltage Operating voltage range Power consumption (under maximum load) Insulation resistance Dielectric strength Noise immunity 100 to 240 VAC 85% to 110% of the rated supply voltage 6 VA max. 4.5 VA max. (24 VAC) 4.5 W max. (24 VDC) K3MA-L 24VAC/VDC, K3MA-L-C 24VAC/VDC 24 VAC (50/60 Hz), 24 VDC

20 M min. (at 500 VDC) between external terminal and case. Insulation provided between inputs, outputs, and power supply. 2,000 VAC for 1 min between external terminal and case. Insulation provided between inputs, outputs, and power supply. 1,500 V on power supply terminals in normal or com- 480 V on power supply terminals in normal mode. mon mode. 1,500 V in common mode. 1 s, or 100 ns for square-wave noise with 1 ns. 1 s, or 100 ns for square-wave noise with 1 ns. Vibration: 10 to 55 Hz, Acceleration: 50 m/s2 5 min each in X, Y, and Z directions for 10 sweeps. 150 m/s2 (100 m/s2 for relay contact outputs) 3 times each on 3 axes, 6 directions. Operating: 10C to 55C (with no condensation or icing) Storage: 25C to 65C (with no condensation or icing) Operating: 25% to 85% (with no condensation) UL61010-1, conforms to EN61010-1 (Pollution degree 2/overvoltage category II) Conforms to VDE0106/P100 (finger protection) (EMI) Emission Enclosure: Emission AC Mains: (EMS) Immunity ESD: EN61326+A1 Industry CISPR 11 Group 1 class A CISPR 11 Group 1 class A EN61326+A1 Industry EN61000-4-2: 4 kV contact discharge 8 kV air discharge Immunity RF-interference: EN61000-4-3: 10 V/m (amplitude-modulated, 80 MHz to 1 GHz) Electrical Fast Transient Noise: EN61000-4-4: 2 kV (power line) Immunity Burst Noise: 1 kV line to line (I/O signal line) Immunity Surge: EN61000-4-5: 1 kV (power line) 2 kV line to ground (power line) Immunity Conducted Disturbance: EN61000-4-6: 3 V (0.15 to 80 MHz) Immunity Voltage Dip/Interrupting: EN61000-4-11: 0.5 cycle, 0, 180, 100% (rated voltage) Approx. 200 g

Vibration resistance Shock resistance Ambient temperature Ambient humidity Approved safety standards EMC

Weight

K3MA-L
Characteristics
Indication accuracy (at 235C) (See note.) Thermocouple: (0.5% of indication value or 1C, whichever greater) 1 digit max. Platinum-resistance thermometer: (0.5% of indication value or 1C, whichever greater) 1 digit max. Thermocouple: K, J, T, E, L, U, N, R, S, B Platinum-resistance thermometer: JPt100, Pt100 Double integral method 500 ms Sampling period (sampling times multiplied by number of averaging times if average processing is selected.) 4 digits (1999 to 9999) 7-segment digital display, Character height: 14.2 mm is displayed automatically with a negative input signal. Leading zeros are not displayed. Input shift equivalent to the setting value supported for all points within the sensor measurement range. Max hold (maximum value), Min hold (minimum value) Programmable with front-panel key inputs (0001 to 9999). Display color change (green (red), green, red (green), red) Average processing (simple average OFF/2/4/8 operations) Setting change lockout Parameter initialization Relay contact (SPDT) 1 s max. Front panel: NEMA4X for indoor use (equivalent to IP66) Rear case: IEC standard IP20 Terminals: IEC standard IP00 + finger protection (VDE0106/100) Non-volatile memory (EEPROM) (possible to rewrite 100,000 times)

Input Measurement method Sampling period Display refresh period Max. displayed digits Display Polarity display Zero display Input shift Hold function Hysteresis setting Other functions

Output Delay in comparative outputs Degree of protection

Memory protection

Note: The indication accuracy of the K thermocouple at a temperature of 200 to 1300C is 2C 1 digit maximum. The indication accuracy of the T and N thermocouples at a temperature of 100C or less is 2C 1 digit maximum. The indication accuracy of the U and L thermocouples at any temperature is 2C 1 digit maximum. The indication accuracy of the B thermocouple at a temperature of 400C or less is unrestricted. The indication accuracy of the R and S thermocouples at a temperature of 200C or less is 3C 1 digit maximum.

Measuring Ranges
Platinum-resistance Thermometer
Input Range Parameter C F 200 to 850 300 to 1500 0 Pt100 199.9 to 500.0 199.9 to 900.0 1 0.0 to 100.0 0.0 to 210.0 2 199.9 to 500.0 199.9 to 900.0 3 JPt100 0.0 to 100.0 0.0 to 210.0 4

Thermocouple
Input Range C F Parameter 200 to 1300 300 to 2300 5 K 20.0 to 500.0 0.0 to 900.0 6 100 to 850 100 to 1500 7 J 20.0 to 400.0 0.0 to 750 8 200 to 400 300 to 700 9 T 199.9 to 400.0 199.9 to 700.0 10 E 0 to 600 0 to 1100 11 L 100 to 850 100 to 1500 12 200 to 400 300 to 700 13 U 199.9 to 400.0 199.9 to 700.0 14 N 200 to 1300 300 to 2300 15 R 0 to 1700 0 to 3000 16 S 0 to 1700 0 to 3000 17 B 100 to 1800 300 to 3200 18

Input/Output Ratings
Relay Contact Output
Item Rated load (UL ratings) Rated carry current Max. contact voltage Max. contact current Max. switching capacity Min. permissible load (P level, reference value) Mechanical life Electrical life (at an ambient temperature of 20C) Resistive load (cos = 1) 5 A at 250 VAC, 5 A at 30 VDC 5 A max. (at COM terminal) 400 VAC, 150 VDC 5 A (at COM terminal) 2,000 VA, 192 W 10 mA at 5 VDC 20,000,000 times min. (at a switching frequency of 1,200 time/min) 100,000 times min. (at a rated load switching frequency of 10 time/min) 375 VA, 30 W Inductive load (cos = 0.4, L/R = 7 ms) 1.5 A at 250 VAC, 1.5 A at 30 VDC

K3MA-L

Connections
Terminal Arrangement
Power supply Output terminals 100- to 240-VAC type or 24-VAC/VDC type (No polarity for 24-VDC connection.)
A1 A2

Models with comparative output OUT1

E1 E2 E3 E4 E5 E6 E4

A B B

Input terminals

E5 E6

For thermocouple input

For platinumresistance thermometer input

Terminal No.
A1 - A2 E4 - E6 - E5 E1 , E2 - E3

Name Operation power Thermocouple or platinum-resistance thermometer input Outputs

Description Connects the operation power supply. Connects the thermocouple or platinum-resistance thermometer input. Outputs the relay outputs.

Block Diagram
Input Input Microcomputer EEPROM Key

Display Output circuit Contact output (See note.)

5V

12 V

Constant voltage circuit

Power supply circuit

Note: Relay output models only.

K3MA-L

Operation
Main Functions
Input Types and Ranges
Parameter in-t 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 N R S B E L U T J Thermocouple K JPt100 Setting Input type Platinum-resistance thermometer Pt100 Meaning 200 to 850C 199.9 to 500.0C 0.0 to 100.0C 199.9 to 500.0C 0.0 to 100.0C 200 to 1300C 20.0 to 500.0C 100 to 850C 20.0 to 400.0C 200 to 400C 199.9 to 400.0C 0 to 600C 100 to 850C 200 to 400C 199.9 to 400.0C 200 to 1300C 0 to 1700C 0 to 1700C 100 to 1800C 300 to 1500F 1999 to 900.0F 0.0 to 210.0F 199.9 to 900.0F 0.0 to 210.0F 300 to 2300F 0.0 to 900.0F 100 to 1500F 0.0 to 750.0F 300 to 700F 199.9 to 700.0F 0 to 1100F 100 to 1500F 300 to 700F 199.9 to 700.0F 300 to 2300F 0 to 3000F 0 to 3000F 300 to 3200F

Note: The initial value is 5: thermocouple K (200 to 1300C/300 to 2300F).

Temperature Unit Selection

Either centigrade (C) or fahrenheit (F) can be selected as the temperature unit. Parameter d-u c f Setting Meaning Display in C. Display in F.

Lower limit (Low Acting): The output is turned ON when the measurement value is less than its set value. Upper and lower limits (Outside Band Acting): An upper limit (H set value) and lower limit (L set value) can be set independently. The output is turned ON when the measurement value is greater than the upper-limit set value or less than the lower-limit set value. Parameter out 1.t hi lo hi-lo Setting Meaning Upper limit: Alarm operates at upper limit. Lower limit: Alarm operates at lower limit. Upper and lower limits: Alarm operates at upper and lower limits.

OUT Types (Comparative Output Models Only)

OUT 1 can be set to operate in one of the three following modes in accordance with the compared values: Upper limit (High Acting): The output is turned ON when the measurement value is greater than its set value.

Upper Limit (High Acting)

Lower Limit (Low Acting)

Upper and Lower Limits (Outside Band Acting)

OUT1 upper-limit value Measurement value OUT1 lower-limit value ON Output OFF

OUT1 value Measurement value Output ON OFF

Hysteresis

Hysteresis

Measurement value OUT1 value Output ON OFF

Hysteresis

Hysteresis

K3MA-L
Temperature Input Shift
Input shift equivalent to the setting value supported for all points within the sensor measurement range. Parameter ins -1999 to 9999
Red

Changing the Display Color

The color of the value displayed can be set to either red or green. For comparative output models, the display color can be set to change from green to red, or from red to green, according to the status of the comparison criterion.

Setting

258.9
Temperature OUT1 value Before shift After shift Temperature input shift value Input Green

192.0

Display Auto-return Time

This function automatically returns the display to the operation levels current value if no keys are pressed for a preset time (called the display auto-return time).

Parameter Initialization
This function returns all of the parameters to their initial values. Parameter init off on Setting --Initializes all parameters. Meaning

Move-to-Protect-Level Time
The time required to shift to the protect level can be set as desired.

MAX/MIN Display
The maximum and minimum measurement (display) values from the time the power is turned ON until the current time can be stored and displayed. This is useful, for example, when measuring the maximum value.
Current value

Use this to reset the K3MA-L after returning it to its factory-set condition.

Average Processing
Average processing stabilizes displayed values to minimize flicker by averaging the fluctuating input signals. Average processing can be performed for the measurement values in either of four steps (OFF, 2 times, 4 times, or 8 times).
MAX/MIN LEVEL MODE SHIFT UP

MAX/MIN

MAX value
Max

MAX/MIN
MAX/MIN LEVEL MODE SHIFT UP

MIN value
Min

This is useful for ignoring rapid fluctuations, e.g., eliminating spike noise.
MAX/MIN LEVEL MODE SHIFT UP

MAX/MIN

Hysteresis (Comparative Output Models Only)

The hysteresis of comparative outputs can be set to prevent chattering in the output when the measurement value fluctuates finely near the OUT value.

Upper limit (high acting)

Set value

Hysteresis

Measurement value

ON Output OFF

K3MA-L

Nomenclature
2. Operation indicators

Max Min

1. Main indicator

3. Level indicator

SV

MAX/MIN

LEVEL

MODE

SHIFT

UP

4. MAX/MIN key 5. Level key

Name 1. Main indicator 2. Opera- 1 tion indica- SV tors Max Min 3. Level indicator 4. MAX/MIN Key 5. Level Key 6. Mode Key 7. Shift Key 8. Up Key Level indicator Displays current values, parameters, and set values. Lit when output 1 is ON. Lit when a set value is being displayed or changed. Lit when the main indicator is showing the MAX value. Lit when the main indicator is showing the MIN value. Displays the current level that the K3MA-L is in. (See below for details.)

8. Up key 6. Mode key 7. Shift key

Functions

Used to display the MAX and MIN values when a measurement value is being displayed. Used to change the level. Used to allow the main indicator to indicate parameters sequentially. Used to enable a set value to be changed. When changing a set value, this key is used to move along the digits. Used to change a set value. Used to set or clear a forced-zero function when a measurement value is being displayed. Level Protect Operation Adjustment Initial setting Advanced-function setting

p
Not lit

a s f

K3MA-L

Dimensions
101.2 91 Finger protective cover (provided)

Main indicator character size

14.2 mm

Panel cut-out
120 min.

96

MAX/MIN

LEVEL

MODE

SHIFT

Application Examples
Monitoring the temperature of an industrial furnace Sending a temperature alarm for molding equipment
PID control E5EN

K3MA-L Industrial furnace Molding Alarmequipment output Alarm output K3MA-L Alarm output

Monitoring the temperature of an industrial furnace/sintering furnace. Monitoring/alarm function for disinfecting equipment.

Monitoring (failsafe checking) abnormal temperatures in molding equipment. Monitoring the liquid temperature for cleaning devices.

85

97 7.6 mm

75 min.

0 92+0.5

12 1.3 80

45 0

+0.5

44.8 48
UP

Mounting Recommended Panel Thickness 1 to 8 mm. Mount the product horizontally. The K3MA-L uses M3 terminals. A terminal cover is provided.

Monitoring the bearing temperature for a generator motor

K3MA-L Generator motor

Monitoring temperature rises in electric power generating facilities. Inspecting temperatures in machines and devices.

K3MA-L

Installation
1. Insert the K3MA-L into the panel cut-out hole. 2. For a waterproof installation, insert the rubber gasket onto the body of the K3MA-L.

Wiring
Use the following M3 crimp terminals.
5.8 mm max.

5.8 mm max.

Unit Labels (Provided)

The unit labels are not attached to the K3MA-L. Select the desired labels from the provided sheet.

3. Fit the adaptor into the grooves on the left and right sides of the rear case, then push it until it contacts the panel to secure the K3MA-L.

Note: For scales and gauges, use the unit labels that are specified by the relevant laws or regulations.

LCD Angle of View

The K3MA is designed to provide the best visibility at the angles shown in the following diagram.

10 30

Rubber Packing (Sold Separately)

K32-P1
If the rubber packing is lost or damaged, it can be ordered using the following model number: K32-P1. (Depending on the operating environment, deterioration, contraction, or hardening of the rubber packing may occur and so, in order to ensure the level of waterproofing specified in NEMA4, periodic replacement is recommended.) Note: Rubber packing is provided with the Controller.

Wiring Precautions
Use crimp terminals. Tighten the terminal screws to a torque of approximately 0.5 Nm. To avoid the influence of noise, route signal lines and power lines separately.

K3MA-L

Operating Procedures
Operations in Run Mode
Checking the Maximum and Minimum Values
The maximum and minimum values can be displayed by pressing the MAX/MIN Key while the measurement is being displayed.

Adjustment Level Operation

Setting Temperature Input Shift Values
Temperature Input Shift
A shift value can be set for a temperature input.
Temperature

Measurement value

MAX/MIN Key

MAX value

MAX/MIN Key

MIN value

MAX/MIN Key

The maximum and minimum values can be reset by pressing the MAX/MIN Key for 1 s min. when the maximum or minimum value is displayed.

Checking and Setting Comparative Set Values (for Models with the Comparative Output Function)
Each time the Mode Key is pressed when the measurement value, maximum value, or minimum value is displayed, the comparative values will be displayed in the following order: OUT1 value (or OUT1 upper-limit value, OUT1 lower-limit value).

After shift

Before shift Input shift value

Measurement value MAX value MIN value

OUT1 value

Input

OUT1 upperlimit value Mode Key

OUT1 lowerlimit value Mode Key

Mode Key

The value set for the temperature input shift is applied to the entire measurement range of the temperature sensor.

10

K3MA-L
Levels
Level refers to a grouping of parameters. The following table lists the operations that are possible in each of the levels, and the diagram tells how to move between levels. There are some parameters that are not displayed for certain models. Level name Protect Operation Adjustment Initial setting Advanced-function setting Setting lockouts. Displaying current values, and setting OUT 1 value. Setting communications writing control. Function Continue Continue Continue Measurement

Making initial settings of input type, output operating action, and other Stopped parameters. Setting average processing, display color settings, and other advanced function parameters. Stopped

Power ON

Operation level + Time set by user (See note.) Protect level + 1 s min.

Adjustment level Less than 1 s

1 s min. 1 s min.

Flashing stops if key is released.

- 123.4
Continue to press the key for 2 s min. Initial setting level

Indicates change of level.

1 s min.

Password "0169"

Advanced-function setting level

Note: The move-to-protect-level time can be set in the advanced-function setting level.

11

K3MA-L
Parameters
Note: 1. Some parameters are not displayed for certain models. 2. The K3MA-L will stop measurement if the level is changed to the initial setting level or the advanced-function setting level. 3. If the input range is changed, some parameters are set to default values. Therefore, set the input range first. 4. Settings displayed in reversed colors are defaults.

Power ON Press Level Key for less than 1 s. Adjustment level Press Level Key for less than 1 s. Current value
Temperature input shift For models with the comparative output function MODE

Operation level

OUT1 value
MODE

Set one of these.

OUT1 upper-limit value

MODE
OUT1 lower-limit value

MODE

12

K3MA-L

Press Level Key for more than 3 s.

Initial setting level
Press Level Key for more than 1 s.

To change a setting, press the Shift Key make the change with the Up Key .

again, and then

Press Level Key

for less than 1 s.

Advanced-function setting level

Input type

Enter password "0169"

Parameter initialization

MODE Temperature unit Temperature unit MODE

Models with the comparative output function

MODE
Average processing

/ /
Unit: times

OUT1 type OUT1 type MODE

Move to advancedfunction setting level
Upper Limit Lower Limit Upper/Lower Limits

MODE
Models with the comparative output function

OUT1 hysteresis
OUT1 Hysteresis

MODE
Display color change
Green (red) Green Red (green) Red

MODE

Password: 0169

MODE
Display auto-return time

Unit: s
MODE
Move-toprotectlevel time

MODE

Unit: s

Settings displayed in reversed colors are initial settings.

13

K3MA-L
Press Level Key + Mode Key for more than 1 s.

Operation Level
Press Level Key + for more than preset time. Mode Key

Protect level

Operation/adjustment lockouts
MODE

/ / / / /

Setting level lockouts

MODE

Setting change lockout

MODE

Operation/Adjustment Lockouts
Restricts key operations for operation level and adjustment level. Parame- Setting ter oapt 0 1 2 Operation level Process value display Allowed Allowed Allowed Set value display Allowed Allowed Prohibited Moving to adjustment level Allowed Prohibited Prohibited

Initial Settings
Power ON

Press the Level Key level.

for 3 s min. to move to the initial setting

Initial setting is 0. This cannot be displayed on models not equipped with the comparative output function.

Select the input type.

Setting Level Lockouts

Restricts shifting to initial setting level or advanced-function setting level. Parameter Setting Shift to initial setting level Shift to advancedfunction setting level Allowed Prohibited Prohibited

If desired, shift to the adjustment level to set the temperature input shift value.

If required, shift to the advanced-function setting level to set the number of measurements for averaging, hysteresis values, auto-zero time, display color change, display auto-return time, or move-to-protect-level time.

icpt

0 1 2

Allowed Allowed Prohibited

Setting Change Lockout

Restricts setting changes by key operation. When this lockout is set, it is no longer possible to shift to a setting change mode. Parameter wtpt off on Setting Setting change by key operation Allowed Prohibited

Press the Level Key operation level.

for less than 1 s min. to return to the

Set the OUT values.

Measurement starts.

However, all protect level parameters can still be changed.

14

K3MA-L
Setting Example
Initial Settings
The settings for the following example are shown here. Here, the temperature inside the furnace is to be displayed in centigrade (C). Temperature sensor: E52-PR Thermocouple, Measurement range: 0 to 1,400C. 1. Set the K3MA-L input type to the thermocouple R input range. Parameter: in-t (input type), Setting value: 16 2. Select centigrade (C) as the temperature unit. Parameter: d-u (temperature unit), Setting value: c If you are using a comparative output model, make the setting as desired.

Example: Monitoring the temperature of an industrial furnace

E52-PR Thermocouple Industrial furnace

1

Max Min

SV

MAX/MIN

LEVEL

MODE

SHIFT

UP

K3MA-L-C 100-240VAC

Troubleshooting
When an error occurs, error details will be displayed on the main indicator. Confirm the error from the main indicator and take the appropriate countermeasures. Level display Not lit e111 Main indicator Error contents RAM memory error Countermeasures Repair is necessary. Consult your OMRON sales representative. When this error is displayed, press the Level Key for 3 seconds, and the settings will be restored to the factory settings. If the error cannot be recovered, repair is necessary. Consult your OMRON sales representative. Confirm that the temperature sensor is correctly connected, and that there are no broken signal lines to the temperature sensor. Input value is out of the specified range (control range). Set the value within the range immediately. If the condition does not return to normal, repair is necessary. Consult your OMRON sales representative.

e111

EEPROM memory error

Not lit

Flashes s.err

Input error

Not lit

Flashes 9999

The measurement value after tem- The temperature input correction perature input correction exceeds value may be inappropriate. 9999. Use the adjustment level to review the temperature input correction value. The measurement value after tem- The temperature input correction perature input correction is lower value may be inappropriate. than 1999. Use the adjustment level to review the temperature input correction value.

Not lit

Flashes -1999

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. In the interest of product improvement, specifications are subject to change without notice.

15

Read and Understand This Catalog

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments.

Warranty and Limitations of Liability

WARRANTY
OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED.

LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.

Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.

Disclaimers
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products.

DIMENSIONS AND WEIGHTS

Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.

PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRONs test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability.

ERRORS AND OMISSIONS

The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions.

2010.11 In the interest of product improvement, specifications are subject to change without notice.

Industrial Automation Company

http://www.ia.omron.com/

OMRON Corporation
(c)Copyright OMRON Corporation 2010 All Right Reserved.