Services Media No.

6040

Fabric Conveyor Belts Installation and Maintenance Guide

Habasit Solutions in motion

2
xa
tio

Re

24

[h]

Introduction

The objective of this Installation and Maintenance Guide is to provide both manufacturer and operator with a comprehensive, albeit summarized overview of the most important aspects of the installation of conveyor systems as it pertains to fabric conveyor belting. Emphasis has been placed on recommendations on installation procedures, belt maintenance and cleaning as well as on storage of the conveyor belt itself. A comprehensive trouble-shooting checklist supports tters and service personnel in taking the right measures if tracking problems arise.

Product liability, application considerations If the proper selection and application of Habasit products are not recommended by an authorized Habasit sales specialist, the selection and application of Habasit products, including the related area of product safety, are the responsibility of the customer. All indications / information are recommendations and believed to be reliable, but no representations, guarantees, or warranties of any kind are made as to their accuracy or suitability for particular applications. The data provided herein are based on laboratory work with small-scale test equipment, running at standard conditions, and do not necessarily match product performance in industrial use. New knowledge and experiences can lead to modications and changes within a short time without prior notice. BECAUSE CONDITIONS OF USE ARE OUTSIDE OF HABASITS AND ITS AFFILIATED COMPANIES CONTROL, WE CANNOT ASSUME ANY LIABILITY CONCERNING THE SUITABILITY AND PROCESS ABILITY OF THE PRODUCTS MENTIONED HEREIN. THIS ALSO APPLIES TO PROCESS RESULTS / OUTPUT / MANUFACTURING GOODS AS WELL AS TO POSSIBLE DEFECTS, DAMAGES, CONSEQUENTIAL DAMAGES, AND FURTHER-REACHING CONSEQUENCES.

Conveyor belt installation

The installation of a conveyor belt consists of the following steps: Checking the conveyor installation, belt installation, putting it into operation and aligning the belt. Checking the installation Prior to belt installation it is extremely important to check the conveyor installation thoroughly and to rectify any faults immediately. Make certain that the drive is switched off and ensure that it cannot be inadvertently switched back on Ensure that all parts of the installation in contact with the belt are clean and free from oil, grease and dirt, etc. Ascertain that the supporting structure is not distorted and is accurately aligned in all planes Ascertain that all pulleys and rollers and nosebars are set axially parallel and exactly at right angles to the belt running direction Check that the installation dimensions are correct. The best method is to measure across the diagonals and is done by marking the ends of the pulleys/rollers exactly at the verticals to the shaft axis (AR,AL, BR, BL). The diagonal distances of points AR BL and AL BR must be exactly identical as well as distances between centers AL BL and AR BR. Note: Identical distances between centers (AL BL and AR BR) alone are no guarantee of the rectangular arrangement of the pulleys/ rollers!

Conveyor belt installation

Belt installation After the checks described before have been completed and any faults rectied, it is necessary to ensure before assembly can start that all tools and equipment needed are on site and that there is a guaranteed energy supply available (electric current, compressed air, water). The tensioning device must be xed on the lowest setting of the take-up The belt ends must be protected from soiling and damage during assembly. The belt should not be twisted or kinked at any time during assembly. Great care must be taken in feeding the belt into the installation In the case of skived and glued joints, care needs to be taken to ensure that goods will not damage or tear the joint. This is particularly important when accumulation takes place. If the belt is to be joined on the installation, the joining instructions must be carefully followed When tensioning the belt, ensure that the tension pulley is adjusted exactly parallel to the belt running direction and that it remains so after tensioning has been completed First-time tensioning Although in practice conveyor belts are often tensioned by feel, it is important to make sure that the driving pulley can drive the belt without slipping even under maximum load. Because synthetic conveyor belts relax after the rst elongation, the effective tensile force decreases during a running-in time of several hours, until the force remains constant. It is important that the belt has been sufciently tensioned already at the installation in order to guarantee slippage-free operation after the relaxation phase. Therefore, the correct tensioning procedure and the observation of a minimal initial elongation are important.

F [N]

1
la

2
xa
tio

Re

24

[h]

F 1 2 3

Tensile force [N] Tensile force immediately after tensioning Effective tensile force after running-in Required tensile force for slippage-free operation after relaxation

Conveyor belt installation

Recommended initial elongation The minimum and maximum admissible initial elongation o vary according to the material used for the traction element: Traction element material Polyester fabric Polyamide fabric Min. initial elongation omin 0.3% 0.5% Max. initial elongation omax around 1% around 3%

The optimal initial elongation can be calculated by help of the Habasit CONVEY-SeleCalc program. If the calculated initial elongation is available, this gure should be used. Procedure for rst-time tensioning 1. Place two measuring marks on a distance of 1,000mm on each side of the untensioned belt 2. Tension the belt with the tensioning device to the required initial elongation o 3. At for example 0.5% initial elongation, the correct tension is achieved, if the distance of the marks has increased to 1005 mm 4. Once the belt has completed at least one circuit of the installation, the distance between the marks is to be measured again and then corrected where necessary

1000 mm 1000 mm

1005 mm 1005 mm

Conveyor belt installation

Belt alignment Since the conveyor belt is following the alignment of the structure and components on which it is operating, it is essential that the conveying installation itself is accurately aligned and that the belt is properly tted by trained personnel. At rst, run the conveyor belt only slowly or intermittently with frequent stops and starts, so that any run-off tendency can be detected quickly and rectied before any damage occurs Make the rst corrections at locations where potential for damaging the belt is greatest Carry out adjustments in small steps, working on only one pulley at a time. Adjustments to multiple pulleys or rollers can adversely affect the tracking characteristics of the belt, causing the system to become unstable and vary with different operating conditions. If guiding pulleys are present, it is recommended to use these elements to align the belt run After each adjustment, allow the belt to rotate a few times to position itself to the new alignment before making any further corrections Bear in mind that each tracking adjustment may result in further adjustments being necessary elsewhere on the installation Cylindrical pulleys which are not at right angles to the belt running direction are not self-tracking and so, with changes in run-off tendency, will need to be reset. Thats why, with reversing operations, the position of cylindrical pulleys should remain exactly at right angles to the belt running direction. In the case of belts with guiding proles, the belt is to be aligned under no-load conditions so that the prole can run in the grooves without running against the groove walls

Conveyor belt installation

Proper untensioning and retensioning Special care has to be taken when a conveyor belt needs to be untensioned (and possibly removed in order to perform maintenance work) and nally installed and tensioned again. Note: Retensioning of a released conveyor belt with the described method for rst-time tensioning (see page 4) results in overtensioning, as the new elongation will be added to the not yet fully released initial elongation. The correct procedure, therefore, is the following: Before (!) slackening the belt, place measuring marks on a distance of for example 1000 mm on each side of the tensioned belt. If the marks of the rst tensioning are still visible, these can be used as well.

1000 mm 1000 mm

Memorize or take a note of the original distance between the measuring marks of the tensioned belt!
x mm

Slacken the belt by releasing the tensioning device. The distance of the measuring marks gets shorter, however, the released length (x) is not of interest.

x mm

After the maintenance work is nished, reinstall the belt and tension it until the measuring marks reach the previously noted distance (for example 1000 mm).

1000 mm 1000 mm

Maintenance and cleaning

Apart from cleaning, conveyor belts made of synthetic materials require little maintenance. Check of the belt tension A periodic check of the belt tension is recommended, particularly where operating conditions are harsh, e.g. frequent starts under full load, signicant temperature uctuations, etc. If the tension is too low, retension the belt until it works again properly. Do not exceed the maximum admissible elongation of the conveyor belt. Cleaning It is important that all parts of the installation that come into contact with the belt are kept as clean as possible. Oil, grease, moisture, rust, dirt, traces of conveyed products, etc. on pulleys, rollers, slider bed and other parts of the installation in contact with the belt may cause operational and belt performance problems and will certainly shorten belt service life. The importance of belt cleanliness with regard to drive, proper tracking response and belt life cannot be overemphasized. Dirt on the conveying side of the belt may also lead to process breakdowns. Obviously hygiene is of particular signicance in the food sector where a number of special cleaning measures must be implemented.

Listed below a few general points on the cleaning of synthetic conveyor belts: Cleaning should, wherever and whenever possible, be carried out when the installation is at rest (safety aspect) In the case of light dirt deposits (dust, etc.), clean with a soft cloth; dry or moistened with cold or warm water Oily, greasy soiling can be removed with hot water and a general, non-abrasive household detergent (low foaming types can aid the rinsing process) Spot cleaning can be performed via a damp rag application of a suitable solvent (see table) Heavy soiling can be removed by scrubbing with hot soapy water or washing with a mild solvent (see table)

Maintenance and cleaning

The following table shows the relative suitability of common detergents and solvents for cleaning of synthetic conveyor belts:
Habasit category of resistance Material cover (conveying side) 1 2 NBR PUR Hamid PA AR Hamid CEL 3 4 5 NBR PUR SI PET Glass 6 TPU PUR+TPU NBR+TPU SI+TPU PET AR BW 7 8 9 10

PA

PVC*

EPDM

PVC**

PTFE

TPO

Habilene

Material traction layer (fabric) Neutral1) Alkaline2) Cleaning agent Acid3) Chloric4) Alcohols5)

PA

PET

PET

PET

AR

PET

PET

List of materials AR BW CEL EPDM NBR PA PET PTFE PUR PVC* PVC ** SI TPO TPU Aramide Cotton Cellulose Ethylene propylene terpolymer rubber Acrylonitrile-butadiene rubber Polyamide Polyester Polytetrauorethylene (Teon) Polyurethane cross-linked Polyvinylchloride (monomer softener) Polyvinylchloride (polymer softener) Silicone Polyolen thermoplastic Polyurethane thermoplastic

Explanation of characters Resistant under standard climatic conditions: 23 C / 73 F, 50% relative humidity Contingently resistant Depending on concentration, duration of impact, thermal and mechanical strain, discoloration, swelling, embrittlement or abrasion are possible Not resistant also at low concentration Examples of cleaning agents 1) 2) 3) 4) 5) Water Soap water, soda, ammonia solution Phosphoric acid (diluted 1%) Javel water (sodium hypochloride solution <1%) Isopropanol, ethanol, methanol, methylated spirit

10

Maintenance and cleaning

Unsuitable solvents are: Aromatic compounds (benzene, toluene, xylene) Chlorinated hydrocarbons (trichloroethylene, tetrachloroethylene, tetrachlorohydrogen) Ketones (acetone, methylethyl ketone)

When working with ammable and/or noxious chemicals, it is vital for you to observe all applicable safety precautions (refer to the corresponding safety data sheets for the chemicals to be employed) Please consult our list Chemical resistance for suitability prior to using chemical substances for cleaning our belts When cleaning with hot water or steam, take care not to exceed the maximum permitted temperature for the belt Caution: Inappropriate cleaning with high-pressure cleaning apparatus may damage the belt The belt should be dried after being cleaned with water Do not immerse belts in water or other uids for long periods. This can result in irreversible dimensional changes (shrinkage), camber, color changes, degradation of the materials, layer separation or premature splice failure, etc. Where brushes are used for cleaning, use only those with soft bristles Special and statutory requirements apply for the cleaning and disinfecting of conveyor belts in the food industry. These regulations must be complied with. For further information, please contact your Habasit specialist

Storage

11

Unfavorable storage conditions or improper handling result in changes in the physical characteristics of most synthetic products. Such changes can, among other things, shorten the service life of the product. The belts should be protected against damage, contamination, moisture, extreme temperatures and UV light, ideally they should be stored in a dark room or in opaque plastic wrap which will also protect the belt against dust and other contaminants. Products containing polyamide should always be wrapped airtight, to avoid undesirable absorption of humidity or drying out. Habasit belts should preferably be stored in their original packaging. Storage Rolls of narrow belts can be stored horizontally on boards or pallets. Several rolls of such products can be stacked as long as the resulting weight does not crush or deform the belts.

Joined belts should be rolled on a hard tube. The tube diameter must not be smaller than the recommended minimum pulley diameter for the belt as this will prevent them from crimping.

Heavy rolls should preferably be stored suspended with the aid of a steel bar or laying on a thick, soft rubber foam bedding.

Handling of heavy rolls To lift a large roll of belts, insert a steel bar through the hole at the core of the roll and attach it to a hoist with two rope slings or chains attached to a crossbeam. To prevent damage to the belt edges by the ropes or chains, the crossbeam must be longer than the width of the roll. Belt rolls can also be transported using forklift trucks. Take care that the outer belt layers are not damaged by the fork edges.

Trouble-shooting of tracking problems

12

Tracking problems in fabric belt conveyors are only in minor cases caused by the belt. Missing or insufcient tracking measures on the installation design, incorrect installation, bad maintenance or wrong countermeasures if tracking problems arise are usually the source of the problems. The following checklist supports tters and service personnel in taking the right measures if tracking problems arise. Source of tracking problem Material build-up on pulleys, rollers, scrapers and on the running side of the belt Solutions (countermeasures) Remove dirt accumulation Improve maintenance and cleaning intervals Install appropriate cleaning devices Straight the frame in all planes Reduce the belt tension Reinforce the installation Set the slider bed horizontally even Clean and lubricate the bearings Improve the maintenance Release the tension Straight the frame in all planes Set all pulleys, rollers, idler, nosebars, etc. exactly at right angles to the belt running axis Tension the belt to the required initial elongation Let the belt run and carry out necessary adjustments in small steps only Do not adjust more than one pulley at once Check if crown height and pulley shape are according to our recommendations; if required remachine the pulley Belt laterally too stiff; change to a more exible belt Increase the belt tension if possible Install further tracking measures or an automatic belt control Set all pulleys, rollers, idlers, nosebars, etc. exactly at right angles to the belt running axis.

Conveyor frame crooked under belt tension, weight of goods or due to uneven oor

Slanted slider bed Sticking pulleys, rollers or idlers Pulleys, rollers or idlers out of square with the running axis of the belt (overadjusted system, conict of tracking means)

Belt distorted permanently by asymmetric tensioning

No or insufcient guiding effect of cylindricalconical pulleys; belt contact with conical parts insufcient

Pivoted cylindrical pulleys or rollers in conveyors with reversal running direction

Guiding proles permanently slide on side of the groove; prole and groove worn off

Track the belt by other means, so that the prole does not touch the groove as soon as no lateral forces appear Check whether the deection at maximum load exceeds the admissible deection Calculate the smallest pulley diameter with respect to deection, e.g. with CONVEY-SeleCalc

Pulley deection too high

Trouble-shooting of tracking problems

13

Source of tracking problem Off-center loading Lateral feeding or lateral diverting

Solutions (countermeasures) Install or adjust chute, funnel or the like to place load on center of the belt Install or adjust means to keep the belt locally tracked 1. Remove the belt 2. Install the belt the other way round 3. Let the belt run and observe the tracking behavior If the belt runs off in the same direction as before, the problem has to be solved on the installation If the belt runs off in the opposite direction as before, the belt is the problem Bow should disappear during running-in If not, tension the belt a bit more In rare occasions the belt has to be replaced Check storage and handling of rolls 1. Remove the belt and let it relax 2. Check the circumference on both sides 3. If the length is not equal on both sides, the belt is irreversibly distorted and has to be replaced Minimal inuence on belt tracking! If the effect cannot be accepted, rejoin the belt

If it is not clear, whether the source of the tracking problem is the belt or inappropriate installation design

Bowed belt (banana)

Belt has been overtensioned and is out of shape due to unequal high tensile stresses

Joint area not right-angled

Detailed information about tracking measures on the installation design can be found in the Fabric Conveyor Belts Engineering Guide.

Notes

14

The Habasit solution

15

Customers first At Habasit we understand that our success depends on your success. This is why we offer solutions, not just products; partnership, not just sales. Since our foundation in 1946, Habasit has brought this understanding of customer needs to life every day and for every application. Thats why were the No. 1 in belting today. Worldwide. Learn more on www.habasit.com

Committed to innovation Habasit is strongly committed to the continuous development of innovative, value-added solutions. Over 3% of our staff are dedicated exclusively to R&D, and our annual investment in this area exceeds 8% of turnover. Certified for quality We deliver the highest quality standards not only in our products and solutions, but also in our employees daily work processes. Habasit AG is certified according to ISO 9001:2000.

Worldwide leading product range Habasit offers the largest selection of belting, conveying, processing and complementary products in the industry. Our response to any request is nothing less than a specific, tailor-made solution.

Fabric based conveyor and processing belts HabaFLOW

Plastic modular belts HabasitLINK /KVP

Positive drive conveyor and processing belts Habasit CleandriveTM

Power transmission belts HabaDRIVE

Timing belts HabaSYNC

Chains (slat and conveyor chains) HabaCHAIN

Machine tapes

Round belts

Seamless belts

Profiles, Guides, Wear strips HabiPLAST

Fabrication tools (joining tools)

Gearmotors Electric motors Motion control

Austria Habasit GmbH, Wien Phone: +43 1 690 66 www.habasit.at Belgium Habasit Belgium N.V., Zaventem Phone: +32 2 725 04 30 www.habasit.be Canada Habasit Canada Ltd., Oakville Phone: +1 905 827 4131 www.habasit.ca China Habasit East Asia Ltd., Hong Kong Phone: +852 2145 01 50 www.habasit.com.hk Habasit (Shanghai) Co., Ltd. Shanghai Phone: +8621 5488 1228 Phone: +8621 5488 1218 www.habasit.com.hk Czech Republic Habasit Bohemia spol. s.r.o., Brno Phone: +4205 41 421 651 www.habasit.cz France Habasit France S.A.S., Mulhouse Phone: +33 389 33 89 03 www.habasit.fr Germany Habasit GmbH Eppertshausen Phone: +49 6071 969 0 www.habasit.de

Hungary Habasit Hungria Kft., Esztergom Phone: +36 33 510 610 www.habasit.hu India Habasit-Iakoka Pvt. Ltd., Coimbatore Phone: +91 422 262 78 79 www.habasitiakoka.com Italy Habasit Italiana SpA Customer Care: Phone: 199 199 333 For int. calls: +39 0438 911444 www.habasit.it Japan Habasit Nippon Co. Ltd., Yokohama Phone: +81 45 476 03 71 www.habasit.co.jp Netherlands Habasit Netherlands BV, Nijkerk Phone: +31 33 24 72 030 www.habasit.nl New Zealand Habasit Australasia Ltd., Hornby Phone: +64 3348 5600 www.habasit.co.nz Norway Habasit Norge A/S, Oslo Phone: +47 81 55 84 58 www.habasit.no Poland Habasit Polska Sp. zo.o., Dbrowa Grnicza, Phone: +48 32 639 02 40 www.habasit.pl

Romania Habasit Import/Export Romania SRL, Bucuresti, Phone: +40 21 323 95 65 www.habasit.ro Russia OOO Habasit Ltd., St. Petersburg Phone: +7 812 325 40 82 www.habasit.ru Singapore Habasit Far East Pte. Ltd.,Singapore Phone: +65 6862 55 66 www.habasit.com.sg Spain Habasit Hispanica S.A., Barber del Valls Phone: +34 93 719 19 12 www.habasit.es Sweden Habasit AB, Hindas Phone: +46 301 226 00 www.habasit.se Switzerland Habasit GmbH, Reinach Phone: +41 61 577 51 00 www.habasit.ch Taiwan Habasit Rossi (Taiwan) Ltd. Taipei Hsien Phone: +886 2 2267 0538 www.habasit.com.tw Turkey Habasit Kayis San. Ve Tic. Ltd. Sti. Yenibosna - Bahcelievler - Istanbul Phone: +90-212-654 94 04 www.habasit.com.tr

Ukraine Habasit Ukraina, Vinnica Phone: +38 0432 58 47 35 www.habasit.ua United Kingdom and Ireland Habasit Rossi (UK) Ltd., Silsden Phone: +44 870 835 9555 www.habasitrossi.co.uk USA Habasit America Conveyor belts, power transmission belts, gearmotors Suwanee, Georgia Phone: +1 800-458-6431 www.habasitamerica.com Habasit America Seamless belts, timing belts Middletown, Connecticut Phone: +1 860 632 2211 www.seamlessbelts.com www.habasync.com Rossi is one of Europes largest manufacturers of gear reducers, gearmotors, inverters, standard and brakemotors, and is a member of the Habasit Group. Rossi S.p.A. Via Emilia Ovest 915/A 41100 Modena Italy Phone: +39 059 33 02 88 www.rossi-group.com [email protected]

Headquarters Habasit AG CH-4153 Reinach-Basel Phone +41 61 715 15 15 Fax +41 61 715 15 55 E-mail [email protected] www.habasit.com

Copyright Habasit AG Subject to alterations Printed in Switzerland Publication data: 6040BRO.CVB-en1210HQR