Ideapad U310 U410 HMM 1st Edition Mar 2012 English

Lenovo IdeaPad U310/410
Hardware Maintenance Manual
Note:
Before using this information and the product it supports, be sure to read the general information under Notices on page 96.
First Edition (March 2012) Copyright Lenovo 2012. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure. LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered pursuant a General Services Administration GSA contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925. 2012 Lenovo
Contents
About this manual........................................iv Safety information.........................................1 General safety ...................................................... 2 Electrical safety .................................................... 3 Safety inspection guide ...................................... 5 Handling devices that are sensitive to electrostatic discharge......................................... 6 Grounding requirements ................................... 6 Safety notices: multilingual translations.......... 7 Laser compliance statement............................. 14 Important service information ...................16 Strategy for replacing FRUs............................. 16 Strategy for replacing a hard disk drive .............................................................. 17 Important notice for replacing a system board ............................................................. 17 Important information about replacing RoHS compliant FRUs ................................................. 18 General checkout ........................................19 What to do first .................................................. 20 Power system checkout .................................... 21 Checking the AC adapter........................... 21 Checking operational charging ................. 21 Checking the battery pack ......................... 22 Related service information .......................23 Restoring the factory contents by using Recovery Disc Set .............................................. 23 Start Recovery Disc (one disc) ................... 23 Operating System Recovery Disc (one or more discs) ................................................... 23 Applications and Drivers Recovery Disc (one or more discs) ...................................... 23 Supplemental Recovery Disc ..................... 23 Passwords........................................................... 24 Power-on password .................................... 24 Hard-disk password ................................... 24 Supervisor password .................................. 24 Power management .......................................... 25 Screen blank state ........................................ 25 Sleep (standby) state ................................... 25 Hibernation state ......................................... 26 Lenovo IdeaPad U310/U410 .......................27 Specifications ..................................................... 27 Status indicators ................................................ 29 Fn key combinations ......................................... 31 Hotkeys ............................................................... 31 FRU replacement notices .................................. 32 Screw notices ................................................ 32 Removing and replacing an FRU .................... 33 1010 Battery pack ......................................... 34 1020 Dummy card........................................ 37 1030 Hard disk drive ................................... 38 1040 DIMM ................................................... 41 1050 PCI Express Mini Card for wireless LAN/WAN .................................................. 43 1060 Fan assembly and Heat Sink assembly........................................................ 45 1070 Keyboard.............................................. 48 1080 System board ....................................... 51 1090 LCD unit............................................... 55 1100 Base cover, bluetooth card, USB board, power assembly and power board............ 57 1110 LCD front bezel................................... 61 1120 LCD panel, LCD cable, hinges and speakers......................................................... 62 1130 Integrated camera ............................... 66 Locations ............................................................. 67 Front view ..................................................... 67 Right-side view ............................................ 68 Bottom and Left-side view ......................... 69 Parts list ............................................................... 70 Overall ........................................................... 71 LCD FRUs ..................................................... 76 Keyboard....................................................... 79 AC adapters.................................................. 92 Power cords .................................................. 93 Notices ......................................................... 96 Trademarks......................................................... 97
iii
About this manual

This manual contains service and reference information for the following Lenovo product: Lenovo IdeaPad U310/U410 Use this manual to troubleshoot problems. The manual is divided into the following sections: The common sections provide general information, guidelines, and safety information required for servicing computers. The product-specific section includes service, reference, and product-specific parts information.
Important: This manual is intended only for trained servicers who are familiar with Lenovo products. Use this manual to troubleshoot problems effectively. Before servicing a Lenovo product, make sure to read all the information under Safety information on page 1 and Important service information on page 16.
iv
Safety information
Safety information
This chapter presents the following safety information that you need to get familiar with before you service a Lenovo computer: General safety on page 2 Electrical safety on page 3 Safety inspection guide on page 5 Handling devices that are sensitive to electrostatic discharge on page 6 Grounding requirements on page 6 Safety notices: multilingual translations on page 7 Laser compliance statement on page 14
Lenovo IdeaPad U310/U410 Hardware Maintenance Manual
General safety
Follow these rules below to ensure general safety: Observe a good housekeeping in the area where the machines are put during and after the maintenance. When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift it. 4. Lift it by standing or pushing up with your leg muscles; this action could avoid the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you. Do not perform any action that causes hazards to the customer, or that makes the machine unsafe. Before you start the machine, make sure that other service representatives and the customer are not in a hazardous position. Please remove covers and other parts in a safe place, away from all personnel, while you are servicing the machine. Keep your toolcase away from walk areas so that other people will not trip it over. Do not wear loose clothing that can be trapped in the moving parts of the machine. Make sure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it. Insert the ends of your necktie or scarf inside clothing or fasten it with the nonconductive clip, about 8 centimeters (3 inches) from the end. Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing. Attention: Metal objects are good electrical conductors. Wear safety glasses when you are hammering, drilling, soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that may be hazardous to your eyes. After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective. Reinstall all covers correctly before returning the machine to the customer. Fan louvers on the machine help to prevent the overheating of internal components. Do not obstruct fan louvers or cover them with labels or stickers.
Safety information
Electrical safety
Observe the following rules when working on electrical equipments. Important: Use only approved tools and test equipments. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges. Do not use such kind of mat to protect yourself from electrical shock. Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly. Do not work alone under hazardous conditions or near the equipment that has hazardous voltages. Disconnect all power before: Performing a mechanical inspection Working near power supplies Removing or installing main units Before you start to work on the machine, unplug the power cord. If you cannot unplug it, ask the customer to power-off the wall box that supplies power to the machine, and to lock the wall box in the off position. If you need to work on a machine that has exposed electrical circuits, observe the following precautions: Ensure that another person, familiar with the power-off controls, is near you. Attention: Another person must be there to switch off the power, if necessary. Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back. Attention: An electrical shock can occur only when there is a complete circuit. By observing the above rule, you may prevent a current from passing through your body. When using testers, set the controls correctly and use the approved probe leads and accessories for that tester. Stand on suitable rubber mats (obtained locally, if necessary) to insulate you from grounds such as metal floor strips and machine frames. Observe the special safety precautions when you work with very high voltages; instructions for these precautions are in the safety sections of maintenance information. Be extremely careful when you measure the high voltages. Regularly inspect and maintain your electrical hand tools for safe operational condition. Do not use worn or broken tools and testers. Never assume that power has been disconnected from a circuit. First, check it to make sure that it has been powered off.
Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. Do not service the following parts with the power on when they are removed from their normal operating places in a machine: Power supply units Pumps Blowers and fans Motor generators and similar units. (This practice ensures correct grounding of the units.) If an electrical accident occurs: Use caution: do not become a victim yourself. Switch off the power. Send the victim to get medical aid.
Safety information
Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potential unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-Lenovo features or options not covered by this inspection guide. If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem. Consider these conditions and the safety hazards they present: Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock) Explosive hazards, such as a damaged CRT face or a bulging capacitor Mechanical hazards, such as loose or missing hardware To determine whether there are any potential unsafe conditions, use the following checklist at the beginning of every service task. Begin the checks with the power off, and the power cord disconnected. Checklist: 1. Check exterior covers for damage (loose, broken, or sharp edges). 2. Turn off the computer. Disconnect the power cord. 3. Check the power cord for: a. A third-wire ground connector in good condition. Use a meter to measure third-wire ground continuity for 0.1 ohm or less between the external ground pin and the frame ground. b. The power cord should be the type specified in the parts list. c. Insulation must not be frayed or worn. 4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage. 8. Check for worn, frayed, or pinched cables. 9. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.
Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.
Notes: 1. Use product-specific ESD procedures when they exceed the requirements noted here. 2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective.
When handling ESD-sensitive parts: Keep the parts in protective packages until they are inserted into the product. Avoid contact with other people. Wear a grounded wrist strap against your skin to eliminate static on your body. Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap. Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices. Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement.
Notes: The use of a grounding system to guard against ESD damage is desirable but not necessary. Attach the ESD ground clip to any frame ground, ground braid, or greenwire ground. When working on a double-insulated or battery-operated system, use an ESD common ground or reference point. You can use coax or connectoroutside shells on these systems. Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.
Safety information
Safety notices: multilingual translations

The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts. Avant de remettre lordinateur sous tension aprs remplacement dune unit en clientle, vrifiez que tous les ressorts, vis et autres pices sont bien en place et bien fixes. Pour ce faire, secouez lunit et assurez-vous quaucun bruit suspect ne se produit. Des pices mtalliques ou des copeaux de mtal pourraient causer un court-circuit. Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, mu sichergestellt werden, da keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehuse vergessen wurden. Der Computer mu geschttelt und auf Klappergerusche geprft werden. Metallteile odersplitter knnen Kurzschlsse erzeugen.
Prima di accendere lelaboratore dopo che stata effettuata la sostituzione di una FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella corretta posizione e non siano sparse allinterno dellelaboratore. Verificare ci scuotendo lelaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi.
Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y dems piezas pequeas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Comprubelo agitando el sistema y escuchando los posibles ruidos que provocaran. Las piezas metlicas pueden causar cortocircuitos elctricos.
Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium. Ne les dmontez pas, ne les rechargez pas, ne les exposez ni au feu ni leau. Ne les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous la rglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle de lhorloge temps rel, veillez nutiliser que les modles cits dans la liste de pices dtaches adquate. Une batterie ou une pile inapproprie risque de prendre feu ou dexploser. Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Beim Ersetzen der Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.
Alcune batterie di riserva contengono una piccola quantit di nichel e cadmio. Non smontarle, ricaricarle, gettarle nel fuoco o nellacqua n cortocircuitarle. Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria dellRTC (real time clock) o la batteria di supporto, utilizzare soltanto i tipi inseriti nellappropriato Catalogo parti. Limpiego di una batteria non adatta potrebbe determinare lincendio o lesplosione della batteria stessa.
Algunas bateras de reserva contienen una pequea cantidad de nquel y cadmio. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deschelas tal como dispone la normativa local. Utilice slo bateras que se encuentren en la lista de piezas. La utilizacin de una batera no apropiada puede provocar la ignicin o explosin de la misma.
Safety information
Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la dmontez pas, ne lexposez ni au feu ni leau. Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous la rglementation en vigueur. Lorsque vous remplacez la batterie, veillez nutiliser que les modles cits dans la liste de pices dtaches adquate. En effet, une batterie inapproprie risque de prendre feu ou dexploser. Akkus enthalten geringe Mengen von Nickel. Sie drfen nicht zerlegt, wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.
La batteria contiene piccole quantit di nichel. Non smontarla, gettarla nel fuoco o nellacqua n cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la batteria, utilizzare soltanto i tipi inseriti nellappropriato Catalogo parti. Limpiego di una batteria non adatta potrebbe determinare lincendio o lesplosione della batteria stessa.
Las bateras contienen pequeas cantidades de nquel. No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite. Deschelas tal como dispone la normativa local. Utilice slo bateras que se encuentren en la lista de piezas al sustituir la batera. La utilizacin de una batera no apropiada puede provocar la ignicin o explosin de la misma.
Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100C (212F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium. Elle prsente des risques dincendie, dexplosion ou de brlures graves. Ne la rechargez pas, ne retirez pas son connecteur polaris et ne la dmontez pas. Ne lexposez pas une temperature suprieure 100C, ne la faites pas brler et nen exposez pas le contenu leau. Mettez la pile au rebut conformment la rglementation en vigueur. Une pile inapproprie risque de prendre feu ou dexploser. Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entznden, explodieren oder schwere Verbrennungen hervorrufen. Batterien dieses Typs drfen nicht aufgeladen, zerlegt, ber 100 C erhitzt oder verbrannt werden. Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Beim Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgefhrt ist. Der Einsatz falscher Batterien kann zu Entzndung oder Explosion fhren.
La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla in acqua. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali). Limpiego di una batteria non adatta potrebbe determinare lincendio o lesplosione della batteria stessa.
La batera de repuesto es una batera de litio y puede provocar incendios, explosiones o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte, ni caliente por encima de los 100C (212F), ni la incinere ni exponga el contenido de sus celdas al agua. Deschela tal como dispone la normativa local.
10
Safety information
Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water at least for 15 minutes. Seek medical care if any symptoms caused by the fluid are present after washing. Si le panneau daffichage cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un mdecin si des symptmes persistent aprs le lavage. Die Leuchtstoffrhre im LCD-Bildschirm enthlt Quecksilber. Bei der Entsorgung die rtlichen Bestimmungen fr Sondermll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgem behandelt wird oder der Computer auf den Boden fllt. Wenn der Bildschirm beschdigt ist und die darin befindliche Flssigkeit in Kontakt mit Haut und Augen gert, sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgesplt und bei Beschwerden anschlieend ein Arzt aufgesucht werden.
Nel caso che caso lLCD si dovesse rompere ed il liquido in esso contenuto entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero permanere.
Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos, lave inmediatamente las reas afectadas con agua durante 15 minutos como mnimo. Obtenga atencin medica si se presenta algn
11
Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin dviter tout risque de choc lectrique, ne retirez pas le cache en plastique protgeant la partie infrieure de la carte dalimentation. Aus Sicherheitsgrnden die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la parte inferiore della scheda invertitore.
Para evitar descargas, no quite la cubierta de plstico que rodea la parte baja de la tarjeta invertida.
Safety notice 7 DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. Bien que le voltage des batteries principales soit peu lev, le court-circuit ou la mise la masse dune batterie peut produire suffisamment de courant pour brler des matriaux combustibles ou causer des brlures corporelles graves. Obwohl Hauptbatterien eine niedrige Spannung haben, knnen sie doch bei Kurzschlu oder Erdung genug Strom abgeben, um brennbare Materialien zu entznden oder Verletzungen bei Personen hervorzurufen.
Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto circuito o a massa pu fornire corrente sufficiente da bruciare materiali combustibili o provocare ustioni ai tecnici di manutenzione.
Aunque las bateras principales tienen un voltaje bajo, una batera cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.
12
Safety information
Safety notice 8 DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unit remplaable en clientle, mettez le systme hors tension, dbranchez tous les cordons dalimentation des socles de prise de courant, retirez la batterie et dconnectez tous les cordons dinterface. Die Stromzufuhr mu abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt wird.
Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di interconnessione.
Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas de corriente elctrica, quite la batera y, a continuacin, desconecte cualquier cable de conexin entre dispositivos.
13
Laser compliance statement

Some models of Lenovo computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser products. If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note the following:
CAUTION Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure. O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui especificados pode resultar em perigosa exposio radiao.
Pour viter tout risque dexposition au rayon laser, respectez les consignes de rglage et dutilisation des commandes, ainsi que les procdures dcrites. Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann gefhrliche Laserstrahlung auftreten.
Lutilizzo di controlli, regolazioni o lesecuzione di procedure diverse da quelle specificate possono provocare lesposizione a.
El uso de controles o ajustes o la ejecucin de procedimientos distintos de los aqu especificados puede provocar la exposicin a radiaciones peligrosas. Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage device could result in exposure to hazardous laser radiation. There are no serviceable parts inside those drives. Do not open.
14
Safety information
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiao por raio laser ao abrir. No olhe fixo no feixe de luz, no olhe diretamente por meio de instrumentos ticos e evite exposio direta com o feixe de luz.
Rayonnement laser si carter ouvert. vitez de fixer le faisceau, de le regarder directement avec des instruments optiques, ou de vous exposer au rayon. Laserstrahlung bei geffnetem Gert. Nicht direkt oder ber optische Instrumente in den Laserstrahl sehen und den Strahlungsbereich meiden. Kinyitskor lzersugr ! Ne nzzen bele se szabad szemmel, se optikai eszkzkkel. Kerlje a sugrnyalbbal val rintkezst! Aprendo lunit vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici e evitare lesposizione diretta al fascio.
Radiacin lser al abrir. No mire fijamente ni examine con instrumental ptico el haz de luz. Evite la exposicin directa al haz.
15
Important service information

This chapter presents the following important service information: Strategy for replacing FRUs on page 16 Strategy for replacing a hard disk drive on page 17 Important notice for replacing a system board on page 17 Important information about replacing RoHS compliant FRUs on page 18 Important: BIOS and device driver fixes are customer-installable. The BIOS and device drivers are posted on the customer support site: http://consumersupport.lenovo.com/.
Strategy for replacing FRUs

Before replacing parts: Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs listed in this manual. After a system board is replaced, ensure that the latest BIOS is loaded to the system board before completing the service action. To download software fixes, drivers, and BIOS, follow the steps below: 1. Go to http://consumersupport.lenovo.com/. 2. Enter the serial number or select a product or use Lenovo smart downloading. 3. Select the BIOS/Driver/Applications and download. 4. Follow the directions on the screen and install the necessary software.
16
Important service information
Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: If you are instructed to replace an FRU, but the replacement does not solve the problem, reinstall the original FRU before you continue. Some computers have both a processor board and a system board. If you are instructed to replace either of them, and replacing one of them does not solve the problem, reinstall that board, and then replace the other one. If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs one by one to see if the symptoms change. Replace only the FRU that changed the symptoms. Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings. Note the current configuration settings (using the View Configuration option); then, when service has been completed, verify that those settings remain in effect.
Strategy for replacing a hard disk drive

Always try to run a low-level format before replacing a hard disk drive. This will cause all customer data on the hard disk to be lost. Make sure that the customer has a current backup of the data before performing this action. Attention: The drive startup sequence in the computer you are servicing may have been changed. Be extremely careful during write operations such as copying, saving, or formatting. If you select an incorrect drive, data or programs can be overwritten.
Important notice for replacing a system board

Some components mounted on a system board are very sensitive. Improper handling can cause damage to those components, and may cause a system malfunction. Attention: When handling a system board: Do not drop the system board or apply any excessive force to it. Avoid rough handling of any kind. Avoid bending the system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.
17
Important information about replacing RoHS compliant FRUs

RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts. If the original FRU parts are non-compliant, replacement parts can also be non-compliant. In all cases if the original FRU parts are RoHS compliant, the replacement part must also be RoHS compliant. Note: RoHS and non-RoHS FRU part numbers with the same fit and function are identified with unique FRU part numbers. Lenovo plans to transit to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovos requirements and schedule in the EU. Products sold in 2005 and 2006 will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant FRUs. RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS implementation date, failed RoHS compliant parts must always be replaced with RoHS compliant ones, so only the FRUs identified as compliant in the system HMM or direct substitutions for those FRUs may be used. Products marketed before June 2006 Products marketed after June 2006 Current or original part Non-RoHS Non-RoHS Non-RoHS RoHS Replacement FRU Can be Non-RoHS Can be RoHS Can sub to RoHS Must be RoHS Must be RoHS Must be RoHS Current or original part Replacement FRU
Note: A direct substitution is a part with a different FRU part number that is automatically shipped by the distribution center at the time of the order.
18
General checkout
General checkout
This chapter presents the following information: What to do first on page 20 Power system checkout on page 21 Before you go to the checkout, make sure to read the following important notes:
Important notes: Only certified trained personnel can service the computer. Before replacing any FRU, read the entire page on removing and replacing FRUs. When you replace FRUs, use new nylon-coated screws. Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer that you are servicing sequence might have been altered. If you select an incorrect drive, data or programs might be overwritten. Replace an FRU only with another FRU of the correct model. When you replace an FRU, make sure that the machine model and the FRU part number are correct by referring to the FRU parts list. An FRU should not be replaced just because of a single, unreproducible failure. Single failures can occur for a variety of reasons that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. Consider replacing an FRU only when a problem recurs. If you suspect that an FRU is defective, clear the error logs and run the test again. If the error does not recur, do not replace the FRU. Be careful not to replace a nondefective FRU.
19
What to do first
When you do return an FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: 1. Name and phone number of servicer 2. Date of service 3. Date on which the machine failed 4. Date of purchase 5. Procedure index and page number in which the failing FRU was detected 6. Failing FRU name and part number 7. Machine type, model number, and serial number 8. Customers name and address Note for warranty: During the warranty period, the customer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer. The following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use. Before checking problems with the computer, determine whether the damage is covered under the warranty by referring to the following list: The following are not covered under warranty: LCD panel cracked from the application of excessive force or from being dropped Scratched (cosmetic) parts Distortion, deformation, or discoloration of the cosmetic parts Plastic parts, latches, pins, or connectors that have been cracked or broken by excessive force Damage caused by liquid spilled into the system Damage caused by the improper insertion of a PC Card or the installation of an incompatible card Improper disk insertion or use of an optical drive Diskette drive damage caused by pressure on the diskette drive cover, foreign material in the drive, or the insertion of a diskette with multiple labels Damaged or bent diskette eject button Fuses blown by attachment of a nonsupported device Forgotten computer password (making the computer unusable) Sticky keys caused by spilling a liquid onto the keyboard Use of an incorrect AC adapter on laptop products The following symptoms might indicate damage caused by nonwarranted activities: Missing parts might be a symptom of unauthorized service or modification. If the spindle of a hard disk drive becomes noisy, it may have been subjected to excessive force, or dropped.
20
General checkout
Power system checkout

To verify a symptom, follow the steps below: 1. Turn off the computer. 2. Remove the battery pack. 3. Connect the AC adapter. 4. Make sure that power is supplied when you turn on the computer. 5. Turn off the computer. 6. Disconnect the AC adapter and install the charged battery pack. 7. Make sure that the battery pack supplies power when you turn on the computer. If you suspect a power problem, see the appropriate one of the following power supply checkouts: Checking the AC adapter on page 21 Checking operational charging on page 21 Checking the battery pack on page 22
Checking the AC adapter

You are here because the computer fails only when the AC adapter is used. If the power-on indicator does not turn on, check the power cord of the AC adapter for correct continuity and installation. If the computer does not charge during operation, go to Checking operational charging. To check the AC adapter, follow the steps below: 1. Unplug the AC adapter cable from the computer. 2. Measure the output voltage at the plug of the AC adapter cable. See the following figure:
Pin 1 2
2 1
Voltage (V DC) +20 0
Note: Output voltage for the AC adapter pin No. 2 may differ from the one you are servicing. 3. If the voltage is not correct, replace the AC adapter. 4. If the voltage is acceptable, do the following: Replace the system board. If the problem persists, go to Lenovo IdeaPad U310/U410 on page 27. Note: Noise from the AC adapter does not always indicate a defect.
Checking operational charging

To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer.
21
Perform operational charging. If the battery status indicator or icon does not light on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon is still off, replace the battery pack. If the charge indicator still does not light on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section.
Checking the battery pack

Battery charging does not start until the Power Meter shows that less than 95% of the total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from being overcharged or from having a shortened life. To check your battery, move your cursor to the Power Meter icon in the icon tray of the Windows taskbar and wait for a moment (but do not click it), and the percentage of battery power remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon. Note: If the battery pack becomes hot, it may not be able to be charged. Remove it from the computer and leave it at room temperature for a while. After it cools down, reinstall and recharge it.
22
Related service information

This chapter presents the following information: Restoring the factory contents by using Recovery Disc Set on page 23 Passwords on page 24 Power management on page 25
Restoring the factory contents by using Recovery Disc Set

When the hard disk drive or solid state drive is replaced because of a failure, no product recovery program is on the new drive. In this case, you must use the Recovery Disc Set for the computer. Order the Recovery Disc Set and the drive at the same time so that you can recover the new drive with the pre-installed software when they arrive. The Recovery Disc Set consists of the following set of DVDs to restore the computer to the original factory configuration.
Start Recovery Disc (one disc)

This disc is used to format the hard disk drive and initiate the recovery process.
Operating System Recovery Disc (one or more discs)

This disc restores the Microsoft Windows operating system.
Applications and Drivers Recovery Disc (one or more discs)

This disc restores the pre-installed applications and drivers on the computer.
Supplemental Recovery Disc

This disc contains additional content, such as software for specific models and updates to the software that was preloaded on the computer. Not all recovery disc sets come with a Supplemental Recovery Disc. To restore the computer to the original factory configuration using the recovery disc set, do the following: 1. Insert the bootable Start Recovery Disc into the optical drive. 2. Start the computer. When the Lenovo logo comes up, immediately press F12; on the boot sequence menu, select the optical drive as the first boot-up device. The computer will boot from the Start Recovery Disc. Follow the on-screen instructions to begin the recovery process. 3. Read the license. If you agree with the terms, select I accept these terms and conditions and then click Next. 4. Insert the Operating System Recovery Disc when prompted and click Yes to begin the operating system recovery process. 5. Insert the Applications and Drivers Recovery Disc when prompted and then click OK to begin the applications and drivers recovery process. 6. If you have a Supplemental Recovery Disc, insert it when prompted and click Yes. If you do not have a Supplemental Recovery Disc, click No.
23
7. When all of the data has been copied from the last disc in the set, remove the disc and restart the computer. Note: The remainder of the recovery process is fully automated and no action is required by you. The computer will restart into the Windows desktop several times and you might experience periods when no activity is apparent on the screen for several minutes at a time. This is normal. 8. When the recovery process is complete, the Welcome to the Microsoft Windows screen is displayed. Follow the instructions on the screen to complete the Windows setup.
Passwords
As many as three passwords may be needed for any Lenovo computer: the power-on password (POP), the hard disk password (HDP), and the supervisor password (SVP). If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered. Exception: If only an SVP is installed, the password prompt does not appear when the operating system is booted.
Power-on password
A power-on password (POP) protects the system from being powered on by an unauthorized person. The password must be entered before an operating system can be booted.
Hard-disk password
There are two hard-disk passwords (HDPs): + User HDP - for the user + Master HDP - for the system administrator, who can use it to get access to the hard disk drive even if the user has changed the user HDP Attention: If the user HDP has been forgotten, check whether a master HDP has been set. If it has, it can be used for access to the hard disk drive. If no master HDP is available, neither Lenovo nor Lenov authorized service technicians provide any services to reset either the user or the master HDP, or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee.
Supervisor password
A supervisor password (SVP) protects the system information stored in the BIOS Setup Utility. The user must enter the SVP in order to get access to the BIOS Setup Utility and change the system configuration. Attention: If the SVP has been forgotten and cannot be made available to the servicer, there is no service procedure to reset the password. The system board must be replaced for a scheduled fee.
24
Power management
Note: Power management modes are not supported for APM operating system. To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby), and hibernation.
Screen blank state

If the time set on the Turn off monitor timer in the operating system expires, the LCD backlight turns off. You can also turn off the LCD backlight by pressing . To end screen blank state and resume normal operation, press .
Sleep (standby) state

When the computer enters sleep (standby) state, the following events occur in addition to what occurs in screen blank state: The LCD is powered off. The hard disk drive is powered off. The CPU stops. Putting your computer into sleep state If you will be away from your computer for only a short time, put the computer into sleep state. When the computer is in sleep state, you can quickly wake it to resume use, and bypass the startup process. To put the computer into sleep state, click menu. and select Sleep from the Start
To wake the computer, do one of the following. Press the power button. Press any key on the keyboard. Also, in the following event, the computer automatically returns from sleep (standby) state and resumes the operation: The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters sleep (standby) state. Wait a few seconds before taking any action to reenter operation mode.
25
Hibernation state
In hibernation state, the following occurs: The system status, RAM, VRAM, and setup data are stored on the hard disk. The system is powered off. To cause the computer to enter hibernation state, follow the steps below: If you are using the ACPI operating system and have defined one of the following actions as the event that causes the system to go into hibernation state, perform that action: Closing the lid. Pressing the power button. Also, the computer goes into hibernation state automatically in either of the following conditions: If a hibernation time has been set on the timer, and if the user does not do any operation with the keyboard, the hard disk drive, the parallel connector, or the diskette drive within that time. If the timer conditions are satisfied in suspend mode. When the power is turned on, the computer returns from hibernation state and resumes operation. The hibernation file in the boot record on the hard disk drive is read, and system status is restored from the hard disk drive. Note: When the SSD and HDD are being configured, the computer will enter hibernation state automatically.
26
Lenovo IdeaPad U310/U410

This chapter presents the following product-specific service references and product-specific parts information: Specifications on page 27 Status indicators on page 29 FRU tests on page 31 Fn key combinations on page 31 FRU replacement notices on page 32 Removing and replacing an FRU on page 33 Locations on page 67 Parts list on page 70
Specifications
The following table lists the specifications of the Lenovo IdeaPad U310/U410: Table 1. Specifications Lenovo IdeaPad U310 Feature Processor Description See the system properties of your computer. You can do this as follows: Click Start, right-click Computer; then from the pull down menu select Properties. Intel Panther point HM77 FSB: 1333 (Sandy Bridge) & 1600 (IVY bridge) SDRAM: 1333 (Sandy Bridge) & 1600 (IVY bridge) PCI bus PCI express bus DMI Intel Integrated DDR3-1333 or DDR3-1600 4 GB SODIMM 1 2.5-inch, 7.0 mm N13M-GE1, 15W 16:9 (1,366 768 pixels) DDR3-1333 or DDR3-1600 8 GB SODIMM 2 2.5-inch, 9.5 mm or 2.5-inch, 7.0 mm NA 16G, 32G mSATA Lenovo IdeaPad U410
Core Chipset Bus architecture
Graphic Chipset Display Standard memory CMOS RAM Hard disk drive Optical drive SSD
256 bytes
27
Table 1. Specifications (continued) Lenovo IdeaPad U310 Feature I/O ports Description HDMI port 1 USB 2.0 1, USB 3.0 2 Audio USB 2.0 2, USB 3.0 2 2 in 1 slot 1 (MMC, SD) Combo audio jack 1 Speaker 2 Built-in microphone HDMI port 1 Intel Wifi 2 2 GN Intel WiMAX/Wifi 1 2 BGN option New Key Board One piece TouchPad 0.3 or 1.0 mega pixels Li-Polymer 40 W or 65 W 65 W or 90 W Win7, Win8 Lenovo IdeaPad U410
Video WLAN WWAN Bluetooth Keyboard Touch pad Integrated camera Battery AC adapter Pre-installed operating system
28
Status indicators
The system status indicators below show the computer status:
29
Table 2. Status indicators Indicator a Power on Meaning On (solid white): The computer is powered on. Blinking: The computer is in sleep mode. off: The computer is powered off. On (solid white): The battery has more than 20% charge. Solid amber: The battery has between 5% and 20% charge. Fast blinking amber: The battery has less than 5% charge. Slow blinking amber: The battery is being charged. When battery charge reaches 20%, the blinking color changes to white. Slow blinking white: The battery has between 20% and 80% charge and is still charging. When the battery reaches 80% charge the light will stop blinking, but charging will continue until the battery is fully charged. Off: The battery is detached.
b Battery
30
Fn key combinations
The following table shows the function of each combination of Fn with a function key. Table 3. Fn key combinations Key combination Fn + Home: Fn + End: Fn + PgUp: Fn + PgDn: Description Activate the pause function. Activate the break function. Enable/Disable the scroll lock. Activate the insert function.
Hotkeys
The hotkeys are located in the function key row of the keyboard.By pressing the appropriate hotkey, you can change system settings instantly. The following describes the function of each hotkey. Table 4. Hotkeys Hotkeys : : : : : : : : : : : : Description Mute/Unmute. Decrease sound volume. Increase sound volume. Close active window or program. Refresh desktop or Web pages. Enable/Disable the touchpad. Open the interface for integrated wireless devices settings (on/off). Enable/Disable the built-in microphone. Turn on/off the integrated camera. Open the interface for changing display devices. Decrease display brightness. Increase display brightness.
31
FRU replacement notices

This section presents notices related to removing and replacing parts. Read this section carefully before replacing any FRU.
Screw notices
Loose screws can cause a reliability problem. In the Lenovo computer, this problem is addressed with special nylon-coated screws that have the following characteristics: They maintain tight connections. They do not easily come loose, even with shock or vibration. They are harder to tighten. Each one should be used only once. Do the following when you service this machine: Keep the screw kit in your tool bag. Always use new screws. Use a torque screwdriver if you have one. Tighten screws as follows: Plastic to plastic Turn an additional 90 after the screw head touches the surface of the plastic part:
more than 90
(Cross-section)
Logic card to plastic Turn an additional 180 after the screw head touches the surface of the logic card:
more than 180
(Cross-section)
Torque driver If you have a torque screwdriver , refer to the Torque column for each step. Make sure that you use the correct screws. If you have a torque screwdriver, tighten all screws firmly to the torque shown in the table. Never use a screw that you removed. Use a new one. Make sure that all screws are tightened firmly. Ensure torque screwdrivers are calibrated correctly following country specifications.
32
Removing and replacing an FRU

This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general rules: 1. Do not attempt to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review FRU replacement notices on page 32. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any of such FRUs are listed at the top of the page. Remove them in the order in which they are listed. 4. Follow the correct sequence in the steps to remove the FRU, as given in the figures by the numbers in square callouts. 5. When turning a screw to replace an FRU, turn it in the direction as given by the arrow in the figure. 6. When removing the FRU, move it in the direction as given by the arrow in the figure. 7. To put the new FRU in place, reverse the removal procedures and follow any of the notes that pertain to replacement. For information about connecting and arranging internal cables, see Locations on page 67. 8. When replacing an FRU, use the correct screw as shown in the procedures.
DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any of the interconnecting cables.
Attention: After replacing an FRU, do not turn on the computer until you have made sure that all screws, springs, and other small parts are in place and none are loose inside the computer. Verify this by shaking the computer gently and listening for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits. Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before touching it, establish personal grounding by touching a ground point with one hand or using an electrostatic discharge (ESD) strap (P/N 6405959) to remove potential shock reasons. Note: The illustrations used in this section are of the Lenovo U410, unless otherwise stated.
33
1010 Battery pack

DANGER Only use the battery specified in the parts list for your computer. Any other battery could ignite or explode. Make sure the battery has been disconnected already before replacing any devices.
Figure 1. Removal steps of battery pack U310: Open four rubber foot pads with a screw driver in the direction shown by arrows a , then remove four screws b.
b b a a a b a
Step
Screw (quantity)
Color
Torque 3.0 kgfcm
2.5 6.8 mm, flat-head, nylok-coated (4) Black
U410: Open three rubber foot pads with a screw driver in the direction shown by arrows a , then remove three screws b.
b b a b a
Step
Screw (quantity) M2.5 8.0 mm, flat-head, nylok-coated (3)
Color Black
Torque 3.0 kgfcm
34
Figure 1. Removal steps of battery pack (continued) Open the back cover along the device frame with a flat blade in the direction shown by arrows and then lift the back cover in the direction shown by arrow c.
U310: Unplug the battery connector in the direction shown by arrow e first, then remove five screws d .
d d d d
e
Step
Screw (quantity)
Color
Torque 2.0 kgfcm
M2.5 3.5 mm, flat-head, nylok-coated Silver (5)
35
Figure 1. Removal steps of battery pack (continued) U410: Unplug the battery connector in the direction shown by arrow e first, then remove three screws d .
e
d d
Step
Screw (quantity) M2.0 3.0 mm, flat-head, nylokcoated (3)
Color Black
Torque 2.0 kgfcm
Remove the battery in the direction shown by arrow f .
When installing: Separate the antenna from other cables. Put them in different tracks to improve signal reception. Make sure to affix the adhesive tape on the battery. Connect the battery last.
36
1020 Dummy card

Figure 2. Removal steps of dummy cards Remove the dummy card in the direction shown by arrows a b . U310:
U410:
37
1030 Hard disk drive

For access, remove these FRUs in order: 1010 Battery pack on page 34 Attention: Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damages and permanent loss of data. Before removing the drive, suggest the customer to backup all the information on it if possible. Never remove the drive while the system is operating or is in suspend mode.
Figure 3. Removal steps of hard disk drive U310: Remove the frame fixing screws a . Pull the tab in the direction shown by arrow b .
a a a a
Step
Color Silver
Torque 2.5 kgfcm
38
Figure 3. Removal steps of hard disk drive (continued) U410: Remove the frame fixing screws a . Pull the tab to disconnect the connector b .
a a a
Step
Color Silver
Torque 2.5 kgfcm
U310: Hold the SATA receptacle connector with one hand and pull the hard disk drive (secured in the metal frame) in the direction shown below to detach the connectors .
39
Figure 3. Removal steps of hard disk drive (continued) U410: Hold the SATA receptacle connector with one hand and pull the hard disk drive (secured in the metal frame) in the direction shown below to detach the connectors .
Remove four screws c and detach the metal frame from the hard disk drive.
c c
c
c
Step
Color Silver
Torque 3.0 kgfcm
When installing: Make sure that the HDD connector is attached firmly.
40
1040 DIMM
For access, remove these FRUs in order: 1010 Battery pack on page 34 Figure 4. Removal steps of DIMM Release the two latches on both edges of the socket at the same time in the direction shown by arrows a, and then unplug the DIMM in the direction shown by arrow b. U310:
41
Figure 4. Removal steps of DIMM (continued) U410:
When installing: Insert the notched end of the DIMM into the socket. Push the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and difficult to be moved.
42
1050 PCI Express Mini Card for wireless LAN/WAN

For access, remove these FRUs in order: 1010 Battery pack on page 34 Figure 5. Removal steps of PCI Express Mini Card for wireless LAN/WAN Disconnect the two wireless LAN cables (black,white) a, and then remove the screw b. U310:
b
U410:
b
In step a, unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159), or pick up the connectors with your fingers and gently unplug them in the direction shown by arrows. Notes: wireless LAN card has 2 cables in step a . wireless LAN card in some models may have 3 cables in step a. Step Screw (quantity) Color Torque 2.0 kgfcm 2.0 kgfcm
M2.0 3.0 mm, flat-head, nylok-coated Black (1) (U310) M2.0 3.0 mm, flat-head, nylok-coated Black (1) (U410)
43
Figure 5. Removal steps of PCI Express Mini Card for wireless LAN/WAN (continued) Remove the card in the direction shown by arrow c . U310:
U410:
When installing: In models with a wireless LAN card that has two antenna connectors, plug the black cable (1st) (MAIN) into the jack labeled 1, and the white cable (2nd) (AUX) into jack labeled 2 on the card. In models with a wireless LAN card that has three antenna connectors, plug the black cable (1st) (MAIN) into the jack labeled 1, the grey cable (3rd) into jack labeled 3, and the white cable (2nd) (AUX) into jack labeled 2 on the card.
44
1060 Fan assembly and Heat Sink assembly

For access, remove these FRUs in order: 1010 Battery pack on page 34 1030 Hard disk drive on page 38 1040 DIMM on page 41 1050 PCI Express Mini Card for wireless LAN/WAN on page 43 Figure 6. Removal steps of fan assembly and heat sink assembly Detach the fan connector in the direction shown by arrow a. U310:
a
U410:
When installing: Make sure that the fan connector is attached firmly to the system board.
45
Figure 6. Removal steps of fan assembly and heat sink assembly (continued) U310: Remove four screws b and screw c .
b b b b c
U410: Remove six screws b and screw c .

b b b b
Step
Screw (quantity) M2.5 3.5 mm, flat-head, nylok-coated (1) M2.5 4.0 mm, flat-head, nylok-coated (1)
Color Silver Silver
Torque 2.5 kgfcm 2.5 kgfcm
b b
46
Figure 6. Removal steps of fan assembly and heat sink assembly (continued) Lift the fan assembly and heat sink assembly in the direction shown by arrow d. Be careful not to damage the connector. U310:
U410:
47
1070 Keyboard
For access, remove this FRU: 1010 Battery pack on page 34 1030 Hard disk drive on page 38 1040 DIMM on page 41 1050 PCI Express Mini Card for wireless LAN/WAN on page 43 1060 Fan assembly and Heat Sink assembly on page 45 Figure 7. Removal steps of keyboard Remove the screws a . U310:
a a
U410:
a a a
Step
Screw (quantity) M2.0 2.5 mm, flat-head, nylok-coated (2) (U310) M2.0 3.0 mm, flat-head, nylok-coated (3) (U410)
Color Silver Silver
48
Figure 7. Removal steps of keyboard (continued) Push the back of the keyboard in the direction shown by arrow b .
Lift the keyboard a little c , and then detach the connector in the direction shown by arrow d . U310:
49
Figure 7. Removal steps of keyboard (continued) U410:
When installing: Make sure that the FPC connector is attached firmly.
50
1080 System board

Important notices for handling the system board: When handling the system board, bear the following in mind. Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite. Avoid rough handling of any kind. In the whole process, make sure not to drop or stack the system board. If you put a system board down, make sure to put it only on a padded surface such as an ESD mat or conductive corrugated material.
For access, remove these FRUs in order: 1010 Battery pack on page 34 1020 Dummy card on page 37 1030 Hard disk drive on page 38 1040 DIMM on page 41 1050 PCI Express Mini Card for wireless LAN/WAN on page 43 1060 Fan assembly and Heat Sink assembly on page 45 1070 Keyboard on page 48
51
Figure 8. Removal steps of system board (continued) Remove four screws a . U310:
a
a a a
U410:
a a a a
Step Screw (quantity)
Color Torque Silver 2.5 kgfcm Silver 2.5 kgfcm
a a
M2.5 3.5 mm, flat-head, nylok-coated (4) (U310) M2.5 4 mm, flat-head, nylok-coated (4) (U410)
52
Figure 8. Removal steps of system board (continued) Unplug the microphone connector in the direction c , DC-IN cable connector in the direction g , speaker connector a , camera connector h , pull the tab to disconnect the LCD connector in the direction f , disconnect power board connector in the direction d e , TP connector in the direction b , IO board connector in the direction i . U310:
h g f
a b
U410:
h
g
d e
When installing: Make sure that all the connectors are attached firmly.
53
Figure 8. Removal steps of system board (continued) Remove the system board in the direction shown by arrow j. U310:
d c b a
U410:
d c b a
When installing: When attaching the system board to the base cover, adjust the placement of the USB, HDMI, RJ-45 port as shown in , and make sure that they are attached to the holes on the base cover as shown. Improper placement of those jacks might cause a damage.
54
1090 LCD unit

For access, remove these FRUs in order: 1010 Battery pack on page 34 1030 Hard disk drive on page 38 1040 DIMM on page 41 1050 PCI Express Mini Card for wireless LAN/WAN on page 43 1060 Fan assembly and Heat Sink assembly on page 45 1070 Keyboard on page 48 1080 System board on page 51 Figure 9. Removal steps of LCD unit Remove four screws a.
aa
aa
Step
Color Silver Silver
When installing: Route the antenna cables along the cable guides. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. Make sure that the LCD connector is attached firmly and make sure that you do not pinch the antenna cables when you attach the LCD assembly. Route the LCD cable along the cable guides.
55
Figure 9. Removal steps of LCD unit (continued) Remove the LCD unit in the direction shown by arrow b .
56
1100 Base cover, bluetooth card, USB board, power assembly and power board
For access, remove these FRUs in order: 1010 Battery pack on page 34 1030 Hard disk drive on page 38 1040 DIMM on page 41 1050 PCI Express Mini Card for wireless LAN/WAN on page 43 1060 Fan assembly and Heat Sink assembly on page 45 1070 Keyboard on page 48 1080 System board on page 51 1090 LCD unit on page 55 Figure 10. Base cover, bluetooth card, USB board, power assembly and power board Lift the power assembly in the direction shown by arrow a . U310:
a
57
Figure 10. Base cover, bluetooth card, USB board, power assembly and power board (continued) Remove two screws b, and then remove the USB board in the direction shown by arrow c.
b
c
Step
Color Silver Silver
When installing: When attaching the USB board to the base cover, adjust the placement of the USB and headphone jack as shown in , and make sure that both of the USB and the headphone jack are attached to the holes on the base cover as shown in . Improper placement of the jacks might cause a damage. Remove the bluetooth card in the direction shown by arrow d .
58
Figure 10. Base cover, bluetooth card, USB board, power assembly and power board (continued) Remove the screw to lift the power board in the direction shown by arrow e .
Step
Color Silver Silver
59
Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following label: The following labels need to be peeled off from the old base cover, and need to be put on the new base cover. e-Standby Label (KOR) COA Label Israel WLAN Label WL Label BT Label KCC Label or WLAN Label for Malaysia/Indonesia For some models, you also need to apply one or two FCC labels. Check the old base cover; if it has one or two FCC labels, find duplicates of them in the label kit and apply them to the new base cover. For the location of each label, refer to the following figure: U310: U410:
a
a
c d
e
c
60
1110 LCD front bezel

For access, remove these FRUs in order: 1010 Battery pack on page 34 1030 Hard disk drive on page 38 1040 DIMM on page 41 1050 PCI Express Mini Card for wireless LAN/WAN on page 43 1060 Fan assembly and Heat Sink assembly on page 45 1070 Keyboard on page 48 1080 System board on page 51 1090 LCD unit on page 55 1100 Base cover, bluetooth card, USB board, power assembly and power board on page 57 Figure 11. Removal steps of LCD front bezel Remove the LCD front bezel in the direction shown by arrows a . U310:
a a a a
61
1120 LCD panel, LCD cable, hinges and speakers

For access, remove these FRUs in order: 1010 Battery pack on page 34 1030 Hard disk drive on page 38 1040 DIMM on page 41 1050 PCI Express Mini Card for wireless LAN/WAN on page 43 1060 Fan assembly and Heat Sink assembly on page 45 1070 Keyboard on page 48 1080 System board on page 51 1090 LCD unit on page 55 1100 Base cover, bluetooth card, USB board, power assembly and power board on page 57 1110 LCD front bezel on page 61 Figure 12. LCD panel, LCD cable, hinges and speakers Remove screws a . U310:
a a a
62
Figure 12. LCD panel, LCD cable, hinges and speakers (continued) U410:
a a aa
aa
Step
Color Silver Silver
Disconnect the connector b , lift the LCD panel in the direction shown by arrow c. U310:
c
When installing: Make sure that the connector is attached firmly.
63
Figure 12. LCD panel, LCD cable, hinges and speakers (continued) Remove screws d and the hinges. U310:
d
dd d
d d
U410:
d d d d dd
dd d d
Step
Color Silver Silver
64
Figure 12. LCD panel, LCD cable, hinges and speakers (continued) Remove two screws e , and then remove the speakers in the direction shown by arrow f .
e e
65
1130 Integrated camera

For access, remove these FRUs in order: 1010 Battery pack on page 34 1030 Hard disk drive on page 38 1040 DIMM on page 41 1050 PCI Express Mini Card for wireless LAN/WAN on page 43 1060 Fan assembly and Heat Sink assembly on page 45 1070 Keyboard on page 48 1080 System board on page 51 1090 LCD unit on page 55 1100 Base cover, bluetooth card, USB board, power assembly and power board on page 57 1110 LCD front bezel on page 61 1120 LCD panel, LCD cable, hinges and speakers on page 62 Figure 13. Removal steps of integrated camera Note: The integrated camera is stuck on the top center of the LCD cover. Unplug the connector in the direction a , Remove the integrated camera from the LCD cover in the direction b .
When installing: Stick the integrated camera to the top center of the LCD cover and ajust the placement of it to make sure the connector is attached firmly.
66
Locations
Front view
a b c d e f g
Integrated camera Computer display Wireless module antennas Power button System status indicators Touchpad Speakers
a
U310:
c d e
U410:
a
c d e
67
Right-side view
a b c d e f g
Built-in microphone Combo audio jack USB port AC power adapter jack Memory card slot HDMI port RJ-45 port
U310:
d c b
U410:
d f e a c c g
68
Bottom and Left-side view

a b c d e f g h
Louvers OneKey Rescue system button Fan louvers RJ-45 port HDMI port USB port Combo audio jack Built-in microphone
U310:
a
b c d f f e
U410:
a
b c f f g
69
Parts list
This section presents the following service parts: Overall on page 71 LCD FRUs on page 76 Keyboard on page 79 Miscellaneous parts on page 91 AC adapters on page 92 Power cords on page 93
Notes: Each FRU is available for all types or models, unless specific types or models are specified.
70
Overall
1
4 6 5 7 8 8 b 10 10 U310 U410 11 U310 U410 9
12 12 U310 13 U410 14
c a
71
Table 4. Parts listOverall

No. 1 2 3 3 3 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 6 7 7 7 8 FRU LCD unit (see LCD FRUs on page 76.) Keyboard (see Keyboard on page 79.) LZ7 Upper Case Grey (U310) LZ7 Upper Case White (U310) LZ8 Upper Case Grey (U410) LZ7 MB UMA I5-2467 1.6G (U310) LZ7 MB UMA I3-2367 1.4G (U310) LZ8 MB DIS I5-2467 1.6G (U410) LZ8 MB DIS I3-2367 1.4G (U410) LZ7 MB UMA I5-3317 1.7G Processor, Ivy Bridge Dual Core ULV, Intel I3-3217U 1.8G L1 3M 2cBGA Processor, Ivy Bridge Dual Core ULV, Intel I5-3317U 1.7G L1 3M 2cBGA Processor, Ivy Bridge Dual Core ULV, Intel I5-3427U 1.8G L1 3M 2cBGA Processor, Sandy Bridge Dual Core ULV, Intel 977 1.4G J1 2M 2cBGA Processor, Sandy Bridge Dual Core ULV, Intel SNB I5-2467M 1.6G 3M J1 BGA Processor, Sandy Bridge Dual Core ULV, Intel I3-2367M 1.4G J1 3M 2cBGA DDR3 1600 2GB, Samsung, M471B5773DH0-CK0 DDR3 1600 2GB DDR3 1600 2GB, Hynix, HMT325S6CFR8C-PB DDR3 1600 2GB DDR3 1600 2GB, Micron, MT8KTF25664HZ-1G6M1 DDR3 1600 2GB DDR3 1600 2GB, Ramaxel, RMT3150ED58E8W-1600 DDR3 1600 2GB DDR3 1600 2GB, Sharetronic(Micron), SM321NH08IAF DDR3 1600 2GB DDR3 1600 4GB, Samsung, M471B5273DH0-CK0 DDR3 1600 4GB DDR3 1600 4GB, Micron, MT16KTF51264HZ-1G6M1 DDR3 1600 4GB DDR3 1600 4GB, Hynix, HMT351S6CFR8C-PB DDR3 1600 4GB DDR3 1600 4GB, Ramaxel, RMT3160ED58E9W-1600 DDR3 1600 4GB DDR3 1600 4GB, Sharetronic(Micron), SM322NQ08IAF DDR3 1600 4GB LZ7 SD Dummy Card (U310) LZ7 SD Dummy Card Grey (U310) LZ8 SD Dummy Card Grey (U410) LZ7 USB2.0 Board (U310) FRU no. CRU ID
90200788 90200789 90200802 90000205 90000204 90000210 90000209 90000280 102500313 102500314 102500315 102500246 102500068 102500152 11200340 11200343 11200346 11200392 11200396 11200341 11200347 11200344 11200393 11200397 90000230 90000231 90000232 90000208
N N ** N N * * * N N N N N N N N N N N N N N N N N N ** N
72
Table 4. Parts listOverall (continued)

No. 8 9 9 9 9 9 9 9 9 9 9 9 9 10 10 11 11 11 11 11 11 12 12 13 13 13 13 FRU LZ8 USB2.0 Board (U410) WLAN, WiFi 1x2 BGN + WiMAX, Intel 6150NX MOW M PCIE NB HMC (LI) (U410) WLAN, WiFi 1x2 BGN + WiMAX, Intel 6150NX BSB M PCIE NB HMC (LI) (U410) WLAN, WiFi 2x2 BGN, Intel 2200N MOW M PCIE NB HMC (U410) WLAN, WiFi 1x1 BGN, CyberTan, Cbt BCM4313 MOW M PCIE NB HMC (U410) WLAN, WiFi 1x1 BGN, Liteon, Liteon AR9285 HB95 BGN MOW NB (U410) WLAN, WiFi 1x1 BGN+BT4.0, CyberTan, Cbt BCM4313HMGB BGN+BT HMC (U410) WLAN, WiFi 1x1 BGN+BT3.0, Liteon, Liteon WB195 BGN+BT HMC (U410) WLAN, WiFi 2x2 BGN, Intel 2200N MOW M PCIE NB HMC (U310) WLAN, WiFi 1x1 BGN, CyberTan, Cbt BCM4313 MOW M PCIE NB HMC (U310) WLAN, WiFi 1x1 BGN, Liteon, Liteon AR9285 HB95 BGN MOW NB (U310) WLAN, WiFi 1x1 BGN+BT4.0, CyberTan, Cbt BCM4313HMGB BGN+BT HMC (U310) WLAN, WiFi 1x1 BGN+BT3.0, Liteon, Liteon WB195 BGN+BT HMC (U310) LZ8 Thermal Module DIS 17W (U410) LZ7 Thermal Module UMA 17W (U310) LZ7 Lower Case Grey (U310) LZ7 Lower Case Pink (U310) LZ7 Lower Case Blue (U310) LZ8 Lower Case Grey (U410) LZ8 Lower Case Red (U410) LZ8 Lower Case Blue (U410) Battery, 3S1P 3cells 4160mAh 46Wh, SMP, Z380+ SMP/ ATL L11M3P01 3S1P 46Wh bty (U310) Battery, 2S2P 4cells 8060mAh 59Wh, SMP Z480+ SMP/ ATL L10M4P11 2S2P 59Wh bty (U410) HDD,500G 5400rpm, WD (ML500M) WD WD5000BPVT24A1YT0 5400PRM 9.5mm 500 HDD HDD,500G 5400rpm, WD (ML375M) WD5000BPVT24HXZT1/WD5000BPVT-24HXZ HDD,500G 5400rpm, Toshiba Capricorn BS Toshiba MK5065GSX 5400RPM 500G HDD,500G 5400rpm, HGST (Jaquar B7) HGST HTS545050A7E380 5400PRM7mm 500G HDD FRU no. 90000213 20002484 20002543 20200048 20002505 20002357 20002501 20002524 20200048 20002505 20002357 20002501 20002524 90200806 90200793 90200790 90200791 90200792 90200803 90200804 90200805 121500058 CRU ID ** ** ** ** ** ** ** ** * * * * * ** N N N N ** ** ** *
121500059 * 16200089 16004846 16004643 16200067 ** ** ** **
73

No. 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 FRU HDD,500G 5400rpm, Seagate Waytt Seagate ST9500325AS 500G 9NB HDD,500G 5400rpm, Seagate M8 ST500LM012 5.4K 9.5 500G HDD HDD,500G 5400rpm, WD(MN500S) WD MN500S HDD,500G 7200rpm, HGST Jaguar C7, HTS725050A7E630 7 7.2K 500G HDD (U410) HDD,500G 7200rpm, WD MX375M, WD WD5000BPKT 7200RPM 500G (U410) HDD,500G 7200rpm, Toshiba Capricorn CS, TSB MK5061GSY 7200PRM 9.5mm 500G HDD (U410) HDD,750G 5400rpm, Toshiba Capricorn CS, Toshiba MK7575GSX 5400RPM 750G HDD (U410) HDD,750G 5400rpm, WD (ML500M), WD WD7500BPVT24A1YT0 5400PRM 9.5mm 750 HDD (U410) HDD,750G 5400rpm, WD (ML375M) WD7500BPVT24HXZT1/WD7500BPVT-24HXZ (U410) HDD,750G 5400rpm, HGSTJaguar B, HTS541075A9E680 9.5 5.4K 750G HDD (U410) HDD,750G 5400rpm, Seagate M8, ST750LM022 5.4K 9.5 750G HDD (U410) HDD,1TB 5400rpm, HGST Jaguar B, HTS541010A9E680 9.5 5.4K 1T HDD (U410) HDD,1TB 5400rpm, WD ML500M, WD WD10JPVT24A1YT0 5400PRM 9.5mm (U410) 1T HDD HDD,1TB 5400rpm, Seagate M8, ST1000LM024 5.4K 9.5 1T HDD (U410) SSD, 16G SSD, Sandisk, Sandisk U100 16G mSATA SSD (U410) SSD, 16G SSD, Lite-on, Lite-on LMT-16M3M 16G mSATA SSD (U410) SSD, 32G SSD, Samsung, Samsung PM830 32G mSATA SSD (U410) SSD, 32G SSD, Sandisk, Sandisk X100 32G mSATA SSD(U410) SSD, 32G SSD, Micron, Micron C400v 32G mSATA SSD (U410) HDD 320G 5400rpm, HGST (Jaquar B7), HGST HTS545032A7E380 5400PRM7mm 320G HDD (U310) HDD 320G 5400rpm, Seagate (Sapta 15), Seagate ST320LT020 5400RPM 7MM 320G (U310) HDD 320G 5400rpm, WD (MN500S), WD MN500S (U310) HDD 500G 5400rpm, HGST (Jaquar B7), HGST HTS545050A7E380 5400PRM7mm 500G HDD (U310) HDD 500G 5400rpm, WD (MN500S), WD MN500S (U310) FRU no. 16004189 16200210 TBD 16200195 16200004 16200086 16005334 16200088 16004848 16200192 16200209 16200193 16200071 16200208 16200215 16200241 16200108 16200162 16200163 16200068 16005211 TBD 16200067 TBD CRU ID ** ** ** * * * * * * * ** ** ** ** ** ** ** ** ** ** ** * * *
74

No. 13 13 13 13 13 14 14 FRU SSD 16G SSD, Sandisk, Sandisk U100 16G mSATA SSD (U310) SSD 16G SSD, Lite-on, Lite-on LMT-16M3M 16G mSATA SSD (U310) SSD 32G SSD, Samsung, Samsung PM830 32G mSATA SSD (U310) SSD 32G SSD, Sandisk, Sandisk X100 32G mSATA SSD (U310) SSD 32G SSD, Micron, Micron C400v 32G mSATA SSD (U310) LZ7 Power Board WO/Cable (U310) LZ8 Power Board WO/Cable (U410) FRU no. 16200215 16200241 16200108 16200162 16200163 90000207 90000212 CRU ID * * * * * N **
75
LCD FRUs
In Lenovo IdeaPad U310/U410, there are following types of LCDs. 17.3 -in. HD TFT
3 4 5
76
17.3-in. HD TFT
Table 5. Parts list17.3-in. HD TFT
No. 1 1 1 2 2 2 2 2 2 3 3 3 4 4 5 5 5 5 5 5 6 6 6 6 6 6 FRU LZ7 LCD Bezel Black (U310) LZ7 LCD Bezel White (U310) LZ8 LCD Bezel Black (U410) Panel 13.3" 16:9 Flat, AUO, AUO B133XTN01.0 HD G F LED1 NB LCD (U310) Panel 13.3" 16:9 Flat, CMI, TBD (310) LZ7 LED Board WO/Cable (U310) Panel 14.0" 16:9 Flat, AUO, AUO B140XTN02.0 HD G F LED1 NB LCD (U410) Panel 14.0" 16:9 Flat, CMI, CMI N140BGE-LB2 HD G F LED1 NB LCD (U410) LZ8 LED Board WO/Cable (U410) LZ7 LED Board Cable (U310) LZ8 LCD Cable LZ7 LCD Cable LZ7 Camera Board 0.3M LZ7 Camera Board 1.0M LZ7 LCD Cover Grey(U310) LZ7 LCD Cover Pink(U310) LZ7 LCD Cover Blue(U310) LZ8 LCD Cover Grey(U410) LZ8 LCD Cover Blue(U410) LZ8 LCD Cover Red (U410) Hinge Antenna, 2.3/2.7 Chengjun, Acon Chengjun U310 2.3/2.7 Hinge ANT Left Hinge Antenna, 2.3/2.7 Sinher, Acon Sinher U310 2.3/2.7 Hinge ANT Left Hinge Antenna, 2.3/2.7 SZS, Acon SZS U310 2.3/2.7 Hinge ANT Left Hinge Antenna, 2.3/2.7 Chengjun, Acon Chengjun U410 2.3/2.7 Hinge ANT Left Hinge Antenna, 2.3/2.7 Sinher, Acon Sinher U410 2.3/2.7 Hinge ANT Left Hinge Antenna, 2.3/2.7 SZS, Acon SZS U410 2.3/2.7 Hinge ANT Left FRU no. 90200786 90200787 90200801 18200262 TBD 90000206 18200263 18200439 90000211 90200795 90201041 90201042 90000322 90000323 90200783 90200784 90200785 90200798 90200799 90200800 20200151 20200153 20200155 20200157 20200159 20200161 CRU ID N N N N N N N N N N
N N N N N N N N N N N N
77
Table 5. Parts list17.3-in. HD TFT (continued)

No. 7 7 7 7 7 7 FRU Hinge Antenna, 2.3/2.7 Chengjun, Acon Chengjun U310 2.3/2.7 Hinge ANT Right Hinge Antenna, 2.3/2.7 Sinher, Acon Sinher U310 2.3/2.7 Hinge ANT Right Hinge Antenna, 2.3/2.7 SZS, Acon SZS U310 2.3/2.7 Hinge ANT Right Hinge Antenna, 2.3/2.7 Chengjun, Acon Chengjun U410 2.3/2.7 Hinge ANT Right Hinge Antenna, 2.3/2.7 Sinher, Acon Sinher U410 2.3/2.7 Hinge ANT Right Hinge Antenna, 2.3/2.7 SZS, Acon SZS U410 2.3/2.7 Hinge ANT Right FRU no. 20200152 20200154 20200156 20200158 20200160 20200162 CRU ID N N N N N N
78
Keyboard
Table 6. Parts listKeyboard
Language Indian Czechoslovakian Bulgarian International English Swiss Slovenian Icelandic Belgian Four Nordic countries Hungarian Hebrew Greek Dutch Japanese Brazilian Arabic German French Russian Traditional Chinese Korean Canadian English&French Latin Portuguese Thai Turkish Spanish Italian U.K. English English Indian Czechoslovakian Bulgarian International English Swiss Slovenian Icelandic Belgian Four Nordic countries Hungarian Hebrew Greek Dutch Japanese Brazilian P/N 25204798 25204797 25204796 25204795 25204794 25204793 25204792 25204791 25204790 25204789 25204788 25204787 25204786 25204785 25204784 25204783 25204782 25204781 25204780 25204779 25204778 25204777 25204776 25204775 25204774 25204773 25204772 25204771 25204770 25204769 25204888 25204887 25204886 25204885 25204884 25204883 25204882 25204881 25204880 25204879 25204878 25204877 25204876 25204875 25204874 CRU ID **
Chicony
U310
Sunrex (white)
79
Table 6. Parts listKeyboard (continued)

Language Arabic German French Russian Traditional Chinese Korean Canadian English&French Latin Portuguese Thai Turkish Spanish Italian U.K. English English Indian Czechoslovakian Bulgarian International English Swiss Slovenian Icelandic Belgian Four Nordic countries Hungarian Hebrew Greek Dutch Japanese Brazilian Arabic German French Russian Traditional Chinese Korean Canadian English&French Latin Portuguese Thai Turkish Spanish Italian U.K. English English P/N 25204873 25204872 25204871 25204870 25204869 25204868 25204867 25204866 25204865 25204864 25204863 25204862 25204861 25204860 25204859 25204978 25204977 25204976 25204975 25204974 25204973 25204972 25204971 25204970 25204969 25204968 25204967 25204966 25204965 25204964 25204963 25204962 25204961 25204960 25204959 25204958 25204957 25204956 25204955 25204954 25204953 25204952 25204951 25204950 25204949 CRU ID **
Sunrex (white) (continued)
U310 (continued)
Darfon
80

Chicony
U310 (continued)
Sunrex
81

Sunrex (continued)
U310 (continued)
Darfon
82

Chicony
U310 (continued)
Sunrex
83

Sunrex (continued)
U310 (continued)
Darfon
84

Chicony
U410
Chicony
85

Chicony (continued)
U410 (continued)
Chicony
86

Sunrex
U410 (continued)
Sunrex
87

Sunrex (continued)
U410 (continued)
Sunrex
88

Darfon
U410 (continued)
Darfon
89

Darfon (continued)
U410 (continued)
Darfon
90
Miscellaneous parts Table 7. Parts listMiscellaneous parts

FRU System miscellaneous parts: (a) LZ7 HDD Bracket (U310) (a) LZ8 HDD Bracket (U410) Cable miscellaneous parts: (b) LZ7 Audio Board Cable (U310) (c) LZ7 HDD Cable (U310) (c) LZ8 HDD Cable (U410) Note: Italicized letters in parentheses are references to the exploded view in Overall on page 71. P/N CRU ID N
90200797 90200808 N 90200796 90200794 90200807
91
AC adapters
Table 8. Parts list3-pin AC adapters
FRU 40W, Delta, Delta ADP-40NH B20V2A adapter (U310) 40W, Liteon, Liteon PA-1400-12LC 20V2A adapter (U310) 40W, Chicony, HIPRO LN-A0403A3C20V2A adapter (U310) 65W, Delta, Delta ADP-65KH BD 20V/3.25A Adapter (U410) 65W, LITEON, Liteon PA-1650-56LC Adapter (U410) 65W, LITEON, Brazil PA-1650-52LB Adapter (U410) 65W, Delta, Delta ADP-65KH B 20V, 3.25A Adapter (U410) 65W, Chicony, Chicony CPA-A065 20V3.25A Adapter (330PF) (U410) 65W Slim 2pin, Delta Slim, Delta ADP-65XB A 20V, 3.25A Adapter (U410) P/N 36001648 36001653 36001672 36001929 36001651 36001714 36002066 36001943 36200019 CRU ID N N N N N N N N N
92
Power cords
A Lenovo power cord for a specific country or region is usually available only in that country or region: Table 9. Parts list3-pin power cords
Region CCC LINETEK PC323+RVV300/300+LS15 1m Argentina LINETEK LS15+H03VV-F+LP39 1m Danmark LINETEK LS15+H03VV-F+LP-38 1m Switzerland LINETEK LS15+H03VV-F+LP-37 1m Brazil LINETEK LS15 H03VV-F LP26A 1m Israel LINETEK LS15+H03VV-F+LP-41 1m UL LINETEK LP-30B + SPT-2 + LS15 1m UK LINETEK LP-61L+ H03VV-F+ LS15 1m Indian LINETEK PE-361+ H05VV-F+ LS15 1m Italy LINETEK LS15+H03VV-F+PE-336 1m Korea LINETEK LS15+H05VV-F+LP-E04A 1m Australia LINETEK LS15+H03VV-F+LP-23A 1m Taiwan LINETEK LS15+VCTF+LP-53 1m Japan LINETEK LS15+VCTF+LP-54 1m Africa LINETEK LS15+H03VV-F+PE-364 1m CE LINETEK LP-34+H03VV-F + LS15 1m CCC Longwell LSG-31+RVV300/300+LS-18 1m Argentina Longwell LP-24+H03VV-F+LS-18 1m Danmark Longwell LP-40+H03VV-F+LS-18 1m Switzerland Longwell LP-37+H03VV-F+LS-18 1m P/N 145000600 145000599 145000598 145000597 145000596 145000595 145000594 145000593 145000592 145000591 145000590 145000589 145000588 145000587 145000586 145000585 145000568 145000567 145000566 145000565 CRU ID *
93
Table 9. Parts list3-pin power cords (continued)

Region Brazil Longwell LP-46+H03VV-F+LS-18 1m Israel Longwell LP-41+H03VV-F+LS-18 1m UL Longwell LP-30B+SPT-2 18AWG+LS-18 1m UK Longwell LP-61L+H03VV-F+LS-18 1m Indian Longwell LP-67+BIS+LS-18 1m Italy Longwell LP-22+H03VV-F+LS-18 1m Korea Longwell LP-486+KTLH03VV-F+LS-5 1m Australia Longwell LP-23A+LFC-3R+LS-18 1m Taiwan Longwell LP-71+VCTF+LS-33 1m Japan Longwell LP-54+VCTF+LS-18 1m Africa Longwell LP-39+H03VV-F+LS-18 1m CE Longwell LP-34A+H03VV-F+LS-18 1m CCC VOLEX GB10S3+RVV 300/500+VAC5S 1m UL Volex US15S3+SPT-2 +VAC5S 1m Indian VOLEX IA6A3+IS694+VAC5S 1m Italy VOLEX IT10S3+HO3VV-F+VAC5S 1m Danmark VOLEX MP233D+H03VV-F+VAC5S 1m Korea VOLEX M2511+KETI IEC+VAC5S 1m Australia VOLEX AU10S3+H03VV-F+VAC5S 1m Taiwan VOLEX TW15CS3+VCTF+VAC5S 1m Japan VOLEX VAC5S+VCTF+M755 1m Argentina VOLEX VA2073+H03VV-F+VAC5S 1m P/N 145000564 145000563 145000562 145000561 145000560 145000559 145000558 145000557 145000556 145000555 145000554 145000553 145000538 145000537 145000536 145000535 145000534 145000533 145000532 145000531 145000530 145000528 CRU ID *
94
Table 9. Parts list3-pin power cords (continued)

Region Brazil P/N 145000527 145000526 145000525 145000524 145000605 CRU ID * *
VOLEX CH10S3+H03VV-F+VAC5S 1m
Israel VOLEX SI16S3+H03VV-F+VAC5S 1m CE VOLEX M2511+HO3VV-F+VAC5S 1m Switzerland VOLEX MP232+H03VV-F+VAC5S 1m UK VOLEX MP5004+H03VV-F+VAC5S 1m
95
Notices
Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the users responsibility to evaluate and verify the operation of any other product, program, or service. Lenovo may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not give you any license to these patents. LENOVO GROUP LTD. PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you. This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. Lenovo may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice. The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Lenovo product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties. All information contained in this document was obtained in specific environments and is presented as an illustration. The result obtained in other operating environments may vary. Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. Any references in this publication to non-Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk.
96
Notices
Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Trademarks
The following terms are either registered trademarks or trademarks of Lenovo in the United States and/or other countries: Lenovo Lenovo logo IdeaPad VeriFace OneKey Rescue (OneKey Recovery, OneKey Antivirus) APS Power Express Energy Management and ReadyComm The following terms are trademarks of Microsoft Corporation in the United States, other countries, or both: Windows Windows 7 The following are trademarks of Intel Corporation or its subsidiaries in the United States, other countries, or both: Intel IntelCore 2 Duo The following is a trademark of Advanced Micro Devices, Inc. AMD Other company, product, or service names may be the trademarks or service marks of others.
97

Ideapad U310 U410 HMM 1st Edition Mar 2012 English

Uploaded by

Copyright:

Available Formats

Ideapad U310 U410 HMM 1st Edition Mar 2012 English

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ideapad U310 U410 HMM 1st Edition Mar 2012 English

Uploaded by

Copyright:

Available Formats

Lenovo IdeaPad U310/410

Hardware Maintenance Manual

About this manual

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Safety inspection guide

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Handling devices that are sensitive to electrostatic discharge

Safety notices: multilingual translations

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Laser compliance statement

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Important service information

Strategy for replacing FRUs

Important service information

Strategy for replacing a hard disk drive

Important notice for replacing a system board

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Important information about replacing RoHS compliant FRUs

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Power system checkout

Checking the AC adapter

Voltage (V DC) +20 0

Checking operational charging

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Checking the battery pack

Related service information

Related service information

Restoring the factory contents by using Recovery Disc Set

Start Recovery Disc (one disc)

Operating System Recovery Disc (one or more discs)

Applications and Drivers Recovery Disc (one or more discs)

Supplemental Recovery Disc

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Related service information

Screen blank state

Sleep (standby) state

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Lenovo IdeaPad U310/U410

Lenovo IdeaPad U310/U410

Core Chipset Bus architecture

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Lenovo IdeaPad U310/U410

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

Lenovo IdeaPad U310/U410

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

FRU replacement notices

Lenovo IdeaPad U310/U410

Removing and replacing an FRU

Lenovo IdeaPad U310/U410 Hardware Maintenance Manual

1010 Battery pack

Torque 3.0 kgfcm

2.5 6.8 mm, flat-head, nylok-coated (4) Black

Screw (quantity) M2.5 8.0 mm, flat-head, nylok-coated (3)

Torque 3.0 kgfcm

Lenovo IdeaPad U310/U410