INTERNATIONAL STANDARD

IEC 62056-42
First edition 2002-02

Electricity metering Data exchange for meter reading, tariff and load control Part 42: Physical layer services and procedures for connection-oriented asynchronous data exchange

Reference number IEC 62056-42:2002(E)

Publication numbering
As from 1 January 1997 all IEC publications are issued with a designation in the 60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1.

Consolidated editions
The IEC is now publishing consolidated versions of its publications. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2.

Further information on IEC publications

The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. Information relating to this publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda. Information on the subjects under consideration and work in progress undertaken by the technical committee which has prepared this publication, as well as the list of publications issued, is also available from the following: IEC Web Site (www.iec.ch) Catalogue of IEC publications The on-line catalogue on the IEC web site (www.iec.ch/catlg-e.htm) enables you to search by a variety of criteria including text searches, technical committees and date of publication. On-line information is also available on recently issued publications, withdrawn and replaced publications, as well as corrigenda. IEC Just Published This summary of recently issued publications (www.iec.ch/JP.htm) is also available by email. Please contact the Customer Service Centre (see below) for further information. Customer Service Centre If you have any questions regarding this publication or need further assistance, please contact the Customer Service Centre: Email: [email protected] Tel: +41 22 919 02 11 Fax: +41 22 919 03 00

INTERNATIONAL STANDARD

IEC 62056-42
First edition 2002-02

Electricity metering Data exchange for meter reading, tariff and load control Part 42: Physical layer services and procedures for connection-oriented asynchronous data exchange

IEC 2002 Copyright - all rights reserved

No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher.

International Electrotechnical Commission 3, rue de Varemb Geneva, Switzerland Telefax: +41 22 919 0300 e-mail: [email protected] IEC web site http://www.iec.ch

Commission Electrotechnique Internationale International Electrotechnical Commission

PRICE CODE

For price, see current catalogue

62056-42 IEC:2002(E)

CONTENTS
FOREWORD ..........................................................................................................................4 1 2 3 4 5 Scope ...............................................................................................................................5 Normative references .......................................................................................................5 Terms, definitions and abbreviations ................................................................................6 Overview ..........................................................................................................................7 Service specification.........................................................................................................8 5.1 List of services ........................................................................................................8 5.1.1 Connection establishment/release related services......................................8 5.1.2 Data communication services ......................................................................8 5.1.3 Layer management services ........................................................................8 5.2 Use of the physical layer services ...........................................................................9 5.3 Service definitions ...................................................................................................9 5.3.1 PH-CONNECT.request ................................................................................9 5.3.2 PH-CONNECT.indication ........................................................................... 10 5.3.3 PH-CONNECT.confirm .............................................................................. 10 5.3.4 PH-ABORT.request ................................................................................... 11 5.3.5 PH-ABORT.confirm ................................................................................... 11 5.3.6 PH-ABORT.indication ................................................................................ 11 5.3.7 PH-DATA.request ...................................................................................... 12 5.3.8 PH-DATA.indication ................................................................................... 12 Protocol specification ..................................................................................................... 13 6.1 Physical layer protocol data unit ............................................................................ 13 6.2 Transmission order and characteristics ................................................................. 13 6.3 Physical layer operation description of the procedures ....................................... 13 6.3.1 General ..................................................................................................... 13 6.3.2 Setting up a physical connection ............................................................... 14 6.3.3 The identification service ........................................................................... 15 6.3.4 Data communications ................................................................................ 19 6.3.5 Disconnection of an existing physical connection....................................... 19

Annex A (informative) An example: PH service primitives and Hayes commands .................. 20 Annex B (informative) Data model and protocol .................................................................... 25 Bibliography.......................................................................................................................... 26

Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure

1 Typical PSTN configuration ....................................................................................7 2 The location of the physical layer ...........................................................................8 3 Protocol layer services of the COSEM 3-layer connection oriented profile ..............9 4 MSC for physical connection establishment.......................................................... 15 5 MSC for IDENTIFY.request/.response message exchange ................................... 17 6 Handling the identification service at the COSEM server side............................... 17 7 Partial state machine for the client side physical layer.......................................... 18 A.1 MSC for physical connection request ................................................................ 20 A.2 Physical connection establishment at the CALLING station ............................... 21 A.3 MSC for physical connection establishment ...................................................... 22 A.4 Data exchange between the calling and called stations..................................... 23 A.5 MSC for a physical disconnection ..................................................................... 24 B.1 The three-step approach of COSEM ................................................................. 25

62056-42 IEC:2002(E)

INTERNATIONAL ELECTROTECHNICAL COMMISSION ___________ ELECTRICITY METERING DATA EXCHANGE FOR METER READING, TARIFF AND LOAD CONTROL Part 42: Physical layer services and procedures for connection-oriented asynchronous data exchange

FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, the IEC publishes International Standards. Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested National Committees. 3) The documents produced have the form of recommendations for international use and are published in the form of standards, technical specifications, technical reports or guides and they are accepted by the National Committees in that sense. 4) In order to promote international unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible in their national and regional standards. Any divergence between the IEC Standard and the corresponding national or regional standard shall be clearly indicated in the latter. 5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with one of its standards. The International Electrotechnical Commission (IEC) draws attention to the fact that it is claimed that compliance with this International Standard may involve the use of a maintenance service concerning the stack of protocols on which the present standard IEC 62056-42 is based. The IEC takes no position concerning the evidence, validity and scope of this maintenance service. The provider of the maintenance service has assured the IEC that he is willing to provide services under reasonable and non-discriminatory terms and conditions for applicants throughout the world. In this respect, the statement of the provider of the maintenance service is registered with the IEC. Information (see also 6.3.3) may be obtained from: DLMS 1 User Association Geneva / Switzerland www.dlms.ch

International Standard IEC 62056-42 has been prepared by IEC technical committee 13: Equipment for electrical energy measurement and load control. The text of this standard is based on the following documents:
FDIS 13/1266/FDIS Report on voting 13/1272/RVD

Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. _________
1 Device Language Message Specification.

62056-42 IEC:2002(E)

This publication has been drafted in accordance with the ISO/IEC Directives, Part 3. Annexes A and B are for information only. The committee has decided that the contents of this publication will remain unchanged until 2006. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended.

A bilingual version of this publication may be issued at a later date.

62056-42 IEC:2002(E)

ELECTRICITY METERING DATA EXCHANGE FOR METER READING, TARIFF AND LOAD CONTROL Part 42: Physical layer services and procedures for connection-oriented asynchronous data exchange

Scope

This part of IEC 62056 specifies the physical layer services and protocols within the Companion Specification for Energy Metering (COSEM) three-layer connection oriented profile for asynchronous data communication. The document does not specify physical layer signals and mechanical aspects. Local, implementation-specific issues are also not specified. In annex A, an example of how this physical layer can be used for data exchange through the Public Switched Telephone Network (PSTN) using intelligent Hayes modems is given. The use of the physical layer for the purposes of direct local data exchange using an optical port or a current loop physical interface is specified in IEC 62056-21. Annex B gives an explanation of the role of data models and protocols in electricity meter data exchange.

Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60050-300:2001, International Electrotechnical Vocabulary Electrical and electronic measurements and measuring instruments Part 311: General terms relating to measurements Part 312: General terms relating to electrical measurements Part 313: Types of electrical measuring instruments Part 314: Specific terms according to the type of instrument IEC/TR 62051:1999, Electricity metering Glossary of terms IEC 62056-21, Electricity metering Data exchange for meter reading, tariff and load control Part 21: Direct local data exchange 1 IEC 62056-46, Electricity metering Data exchange for meter reading, tariff and load control Part 46: Data link layer using HDLC protocol 1 IEC 62056-53, Electricity metering Data exchange for meter reading, tariff and load control Part 53: COSEM application layer 1 IEC 62056-61, Electricity metering Data exchange for meter reading, tariff and load control Part 61: OBIS Object identification system 1 IEC 62056-62, Electricity metering Data exchange for meter reading, tariff and load control Part 62: Interface objects 1 NEMA C12.21:1999, Protocol Specification for Telephone Modem Communication _________
1 To be published.

62056-42 IEC:2002(E)

3
3.1

Terms, definitions and abbreviations

Terms and definitions

For the purpose of this part of IEC 62056, the definitions in IEC 60050-300 and IEC/TR 62051 as well as the following definitions apply: 3.1.1 client a station asking for services, normally the master station 3.1.2 master central station station which takes the initiative and controls the data flow 3.1.3 server a station delivering services. The tariff device (meter) is normally the server, delivering the requested values or executing the requested tasks 3.1.4 slave station responding to requests of a master station. The tariff device (meter) is normally a slave station 3.2 Abbreviations COmpanion Specification for Energy Metering Data Communication Equipment (communications interface or modem) Data Terminal Equipment (computers, terminals or printers) Message Sequence Chart Protocol Data Unit PHysical layer PHysical layer Protocol Data Unit PHysical layer Service Data Unit Service Data Unit

COSEM DCE DTE MSC PDU PH PHPDU PHSDU SDU

62056-42 IEC:2002(E)

Overview
From the external point of view, the physical layer provides the interface between the DTE and the DCE, see

Figure 2. Figure 1 shows a typical configuration for data exchange through a wide area network, for example the PSTN. COSEM client COSEM server

DTE

DCE

DCE

DTE
Sch lumb erg er

Transit network

00001,6 (o) N 00012356

kWh

10 (40)A 230V 50Hz

DTE to DCE ITU-T V series EIA RS232, RS485 Hayes, etc...

DCE to DTE ITU-T V series EIA RS232, RS485 Hayes, etc

IEC 235/02

Figure 1 Typical PSTN configuration From the physical connection point of view, all communications involve two sets of equipment represented by the terms caller system and called system. The caller is the system that decides to initiate a communication with a remote system known as the called party; these denominations remain valid throughout the duration of the communication. A communication is broken down into a certain number of transactions. Each transaction is represented by a transmission from the transmitter to the receiver. During the sequence of transactions, the caller and called systems take turns to act as transmitter and receiver. From the data link point of view the central station normally acts as a master, taking the initiative and controlling the data flow. The tariff device is the slave, responding to the master station. From the application point of view the central station normally acts as a client asking for services, and the tariff device acts as a server delivering the requested services. The situation involving a caller client and a called server is undoubtedly the most frequent case, but a communication based on a caller server and a called client is also possible, in particular to report the occurrence of an urgent alarm. For the purpose of local data exchange, two DTEs can be directly connected using appropriate connections. To allow using a wide variety of media, this standard does not specify the physical layer signals and their characteristics. However, the following assumptions are made: the communication is point to point or point to multipoint; both half-duplex and duplex connections are possible; asynchronous transmission with 1 start bit, 8 data bits, no parity and 1 stop bit (8N1).

62056-42 IEC:2002(E)

From the internal point of view, the physical layer is the lowest layer in the protocol stack. COSEM client DTE Client application Application layer Data Link COSEM server DTE Server application Application layer Data Link layer Physical layer
IEC

layer

Physical layer

Data comm. equipment (DCE)

Data comm. equipment (DCE)

Protocol

236/02

Figure 2 The location of the physical layer This standard defines the services of the physical layer towards its peer layer(s) and the upper layers, and the protocol of the physical layer.

5
5.1

Service specification
List of services

ITU-T X.211 defines a set of capabilities to be made available by the physical layer over the physical media. These capabilities are available via service primitives, as follows: 5.1.1 Connection establishment/release related services

PH-CONNECT.request / PH-CONNECT.indication / PH-CONNECT.confirm PH-ABORT.request / PH-ABORT.confirm / PH-ABORT.indication 5.1.2 Data communication services

PH-DATA.request / PH-DATA.indication 5.1.3 Layer management services

In addition to the services above, some additional physical layer services may be necessary, which are used by or provided for the layer management process, which is part of the application process. Some examples are given below: PH-INITIALIZE.request / PH-INITIALIZE.confirm PH-GET_VALUE.request / PH-GET_VALUE.confirm PH-SET_VALUE.request / PH-SET_VALUE.confirm PH-LM_EVENT.indication As these services are of local importance only, their definition is not within the scope of this standard.

Protocol

Transit network

62056-42 IEC:2002(E) 5.2 Use of the physical layer services

Figure 3 shows how different service users use the service primitives of the physical layer.

Application

Layer management process

Application process
ASO services

Physical connection manager

AL management services

Protocol

Connect/disconnect and data related services DL management services PH-DATA.req /.ind PH-ABORT.ind PH management services

Data link layer

Physical layer
IEC 237/02

Figure 3 Protocol layer services of the COSEM 3-layer connection oriented profile As is shown in Figure 3, the connection establishment/release services are used by and provided for the physical connection manager application process, and not the data link layer. The reasons for this are explained in 6.3.1. 5.3 5.3.1 Function This primitive is invoked by the service user entity to request the setting up of a physical connection to a remote device.
NOTE In the COSEM environment, it is the physical connection manager application process.

Service definitions PH-CONNECT.request

Service parameters The semantics of the primitive is as follows: PH-CONNECT.request ( PhConnType, PhConnReqParams ) The PhConnType parameter specifies the type of connection requested, for example direct connection, PSTN modem connection, etc. This standard does not specify data/type(s) and/or value(s) for this parameter, because this is a local issue only.

PH-CONNECT.req /.cnf /.ind PH-ABORT.req /.cnf /.ind PH-DATA.req /.ind

Application layer

 10

62056-42 IEC:2002(E)

The structure and the contents of the PhConnReqParams parameter depend on the value of the PhConnType parameter. For example, in the case of a PSTN connection it includes the phone number of the remote station, etc. As similarly to the PhConnType parameter the PhConnReqParams parameter contains implementation dependent data, data types/values for this parameter are not specified in this standard. Use The PH-CONNECT.request primitive is used for the establishment of a physical connection. The receipt of this primitive causes the PH-Layer entity to perform the required actions, for example dial the specified phone number, to establish a physical connection with the peer physical layer entity. An example of these actions in the case of an intelligent Hayes modem is given in annex A. 5.3.2 Function This primitive is generated by the physical layer entity to indicate to the service user entity that a remote device requests that a physical connection to the local physical layer be established. Service parameters The semantics of the primitive is as follows: PH-CONNECT.indication ( ) Use The PH-CONNECT.indication primitive is used by the PH entity to indicate to the service user entity that a remote device requests that a physical connection be established. 5.3.3 Function This primitive is generated by the PH entity to convey the results of the associated PHCONNECT.request to the service user entity. Service parameters The semantics of the primitive is as follows: PH-CONNECT.confirm ( Result, PhConnCnfParams ) The result parameter indicates whether the attempt to set up a physical connection was successful or not. The structure and the value of the PhConnCnfParams parameter depend on the physical connection type of the corresponding CONNECTION.request service, which is actually being confirmed. For example, in the case of a PSTN connection it may include parameters of the established connection (V22, baud-rate, etc.). Data types and values for either the Result or the PhConnCnfParams parameter are not specified in this standard. If the connection could not be established due to a local error for example the phone line is not available the PH-CONNECT.confirm service is locally generated. PH-CONNECT.confirm PH-CONNECT.indication

62056-42 IEC:2002(E) Use

11

The PH-CONNECT.confirm primitive is used by the PH entity to convey the results of the associated PH-CONNECT.request. 5.3.4 Function This primitive is invoked by the service user entity to request the disconnection of an existing physical connection. Service parameters The semantics of the primitive is as follows: PH-ABORT.request ( ) Use The PH-ABORT.request primitive is used to request the physical layer entity to terminate an existing physical connection. 5.3.5 Function This primitive is generated by the physical layer entity to indicate to the service user entity whether the request to terminate the physical connection was successful or not. Service parameters The semantics of the primitive is as follows: PH-ABORT.confirm ( Result ) The Result parameter carries the result of the physical disconnection attempt. Use The PH-ABORT.confirm primitive is used by the PH entity to confirm to the service user entity the result of a physical disconnection attempt. 5.3.6 Function This primitive is generated by the physical layer entity to indicate to the service user entity a non-requested termination of a physical connection. Service parameters The semantics of the primitive is as follows: PH-ABORT.indication( ) PH-ABORT.indication PH-ABORT.confirm PH-ABORT.request

 12 Use

62056-42 IEC:2002(E)

The PH-ABORT.indication primitive is used by the PH entity to inform the service user entity that a physical connection has been unexpectedly terminated. 5.3.7 Function This primitive is invoked by the service user entity to request sending a data byte to one or several remote PH entity or entities using the PH transmission procedures. Service parameters The semantics of this primitive is as follows: PH-DATA.request ( Data ) The data parameter carries the byte to be transmitted by the PH layer entity. Use The PH-DATA.request primitive is used by the service user entity whenever data is to be transmitted to its peer entity or entities. The receipt of this primitive causes the PH entity to perform all PH specific actions and pass the PH service data unit the received byte to the physical data interface for transfer to the peer PH entity or entities. 5.3.8 Function This primitive is used to transfer data from the PH entity to the service user entity. Service parameters The semantics of this primitive is as follows: PH-DATA.indication ( Data ) The data parameter carries the received byte as received by the local PH entity. Use The PH-DATA.indication primitive is used by the PH entity to indicate to the service user entity the arrival of a valid data byte. PH-DATA.indication PH-DATA.request

62056-42 IEC:2002(E)

13

6
6.1

Protocol specification
Physical layer protocol data unit (PHPDU)

The PHPDU is specified to be one byte. For transmission purposes however this data byte may be extended (error detection / correction) or modified (bit-stuffing) by the modem device, depending on the modulation scheme used. See also explanation to Figure A.4 Data exchange between the calling and called stations. 6.2 Transmission order and characteristics

The PHSDU byte the data parameter of the PH-DATA services shall be completed with one start bit and one stop bit before transmission. The resulting frame shall be transmitted starting with the start bit, followed by the least significant bit first, with the least significant bit identified as bit 0 and the most significant bit as bit 7. All characteristics of the physical medium and the signal(s) used on this medium are not in the scope of this international standard. 6.3 6.3.1 Physical layer operation description of the procedures General

The physical layer together with the physical media is a shared resource for the higher protocol layers. Multiple higher layer connections/associations can be modelled as different instances of the protocol stack, which need to share the resources of the physical layer. For this reason, the physical connection manager application process manages the physical connection establishment and release see 6.3.2 and 6.3.5. Any application process wishing to use the COSEM protocol shall check the connection state of the physical layer before requesting a connection. If the physical layer is in non-connected state, it shall request the physical connection manager to establish the connection. If the application layer (see IEC 62056-53) invokes an COSEM-OPEN.request service and the corresponding physical connection is not established, the COSEM-OPEN.request will be locally confirmed with error = NO_PHYSICAL_CONNECTION (see in detail in IEC 62056-53). Once the physical connection is established, the physical layer is ready to transmit data. An optional identification service as described in 6.3.3 is available. This enables the client to identify the protocol stack implemented in the server. After the identification procedure is completed or if it is not used the upper protocol layers and the applications can exchange data see 6.3.4. The user of the PH-DATA services is the next protocol layer above the physical layer. A physical disconnection may be requested by the physical connection manager (either on the server or the client side), or may occur in an unsolicited manner (e.g. the phone exchange cuts the line). While physical disconnection management is the exclusive responsibility of the physical connection manager, indication of an unsolicited disconnection (PH-ABORT.indication) is sent both to the next protocol layer and to the physical connection manager. See 6.3.5.

 14 6.3.2 Setting up a physical connection

62056-42 IEC:2002(E)

Both the client and the server device can act as a calling device, initiating a physical connection to a remote device, which is the called device. The execution of the PH-CONNECT.request service depends on the physical connection type and on the modem used. In Annex A, an example is given as to how this is performed in the case when intelligent Hayes modems are used through the PSTN. In other cases, all the operations required dialling, handling eventual error messages (busy, etc ), negotiating the line modulation/baud-rate parameters, etc. might be executed by the physical layer itself. In order to allow using a wide variety of physical connection types, this international standard does not specify how the execution of the PH-CONNECT.request should be done. At the called device side, when the physical connection initiation is detected, the connection needs to be managed: negotiated and accepted or refused. These actions similarly for the execution of the PH-CONNECT.request service depend on the physical connection type and on the modem used, and might be done in an autonomous manner or by the physical layer itself. The specification of these actions is not within the scope of this standard. When the physical layers of the Calling and Called device complete establishing (or not establishing) the required physical connection, they inform the service user entity about the result, using the PH-CONNECT.confirm (calling side) and the PH-CONNECT.indication (called side) service primitives. In this COSEM profile, the service user of these service primitives is exclusively the physical connection manager process.

62056-42 IEC:2002(E) Calling device

15 Called device

Physical connection manager process

Physical layer

Optional external device (MODEM)

Optional external device (MODEM)

Physical layer

Physical connection manager process

The physical layers of the calling and called devices are physically disconnected
PH-CONNECT.request A B C D E F G H PH-CONNECT.confirm I PH-CONNECT.indication

The physical layers of the calling and called devices are physically connected

IEC

238/02

Figure 4 MSC for physical connection establishment As it is shown in Figure 4, this standard specifies only the PH-CONNECT.request/ .confirm/ .indication services: all other eventual message exchanges (A, B, C,.I) are out of the scope of this standard. 6.3.3 6.3.3.1 The identification service General

The optional identification service is an application level service. Its purpose is to allow the client to obtain information about the protocol stack implemented in the server. Consequently, the identification service does not use the whole protocol stack; identification messages are exchanged directly between the application processes of the client and the server, using the data services of the physical layer. If more than one server is used in a multidrop configuration, the client is able to identify the protocol stack in each. The identification service shall be the first service after establishing the physical connection. Although the connection can be initiated either by the client or the server, the identification request is always issued by the client.
NOTE As the identification service is the first service after establishing a physical connection, the physical connection manager application process could also provide this service.

6.3.3.2

Identification service message specification

IDENTIFY.request The IDENTIFY.request message is issued by the application process of the client.

 16 IDENTIFY.request ::= SEQUENCE { IDENTIFY-Request-ID Multidrop-Device-ID } Unsigned8 = 0x20 1) ,

62056-42 IEC:2002(E)

OCTET STRING( SIZE (2) ) OPTIONAL

When the multidrop-device-ID parameter is present, it addresses one physical device on a multi-drop configuration. Only the addressed device shall respond.
NOTE In multidrop configurations, the client has to send the I-command with an address field.

If the server side physical layer accepts this message as an identification message, it will be indicated to the identification service user application process as an IDENTIFY.indication message. IDENTIFY.response The IDENTIFY.response message is issued by the application process of the server and carries the result of the identification request: the protocol standard, version and revision information or an error message. On the client side, this is an IDENTIFY.confirm message. IDENTIFY.response ::= SEQUENCE { success-code Unsigned8 = <OK> std-protocol-id std-protocol-ver std-protocol-rev }
NOTE The response in case of success shall be sent with a delay of 1 500 ms maximum.

-- 2) -- 2) -- 2) -- 2)

Unsigned8, Unsigned8, Unsigned8

The following codes shall be used, in conformance with NEMA C12.21: success-code std-protocol-id std-protocol-ver std-protocol-rev 0x00 0x04 0x01 0x00

If there was a problem with the identification message received, the received message shall be discarded and no response shall be sent. Otherwise, the response contains the success code <OK> and the identifier, version and revision of the protocol stack implemented. These identifiers are administrated by the DLMS User Association. Important note: The IDENTIFY.request/.response messages are not encoded in A-XDR, like other PDUs: they are encoded simply as a sequence of bytes. This means that the IDENTIFY.request/indication message contains one byte or three bytes when the optional multidrop-device-id is present. The IDENTIFY.response/.confirm message contains four bytes in case of success.

_________
1)

In order to ensure compliance to existing implementations, the ASCII code of the I character (0x49) may also be used as Identify-Request-ID. As specified in NEMA C12.21.

2)

62056-42 IEC:2002(E) 6.3.3.3

17

Identification service protocol specification

Figure 5 shows the message sequence chart of the identification service in the case of success.
Client side identification service user application process Client side identification service provider application process Server side identification service provider application process Server side identification service user application process

Client physical layer

Server physical layer

Physical connection is established IDENTIFY.request

PH-DATA.req (0x20) PH-DATA.ind (0x20)

IDENTIFY.indication

PH-DATA.ind (<ok>)

IDENTIFY.resonse ( <ok>, <std>, <id>, PH-DATA.req (<std>) <rev>) PH-DATA.req (<ok>) PH-DATA.req (<id>) PH-DATA.req (<rev>)

PH-DATA.ind (<std>) IDENTIFY.confirm ( PH-DATA.ind (<id>) <ok>, <std>, <id>, PH-DATA.ind (<rev>) <rev>)

IEC

239/02

Figure 5 MSC for IDENTIFY.request/.response message exchange Figure 6 shows the partial state-machine of the identification service of the server side physical layer.

Physical disconnection demanded/detected

DISCONNECTED IDLE Physical disconnection demanded/detected PH-DATA.req Wait reception Byte received Send byte

Physical connection established

Byte received Put byte into buffer; Nb_of_received_char++ ;

Identification is in progress

End of message PH-DATA.ind(Byte1), [PH-DATA.ind(Byte2), PH-DATA.ind(Byte3)]

PH-DATA.req Send byte

No Nb_of_received_char>3

Yes

Data communications (identification is over)

CONNECTED

IEC

240/02

Figure 6 Handling the identification service at the COSEM server side

 18

62056-42 IEC:2002(E)

The COSEM server physical layer enters the CONNECTED macro-state following the establishment of the physical connection and waits for the first byte of the IDENTIFY.request message in the wait reception state. The IDENTIFY.request message contains one or three bytes. For coherency, it shall be sent with the timing constraints of the data link layer (inter-character- and response time-outs). When this first character is received, the physical layer enters the identification is in progress state, waiting for more bytes or an inter-frame time-out, meaning the end of the message. If the end of message condition is detected before receiving more than three bytes the physical layer considers the message received as an IDENTIFY.request message. It sends the bytes received to the (physical connection manager) application process using the PHDATA.indication service and returns to the wait reception state, allowing resolution of eventual errors. On the other hand, if no end of message condition is detected before receiving the fourth incoming byte, the physical layer considers that the identification process is over, and enters into data communications state. The incoming bytes shall be sent, using the PHDATA.indication service, to the service user upper protocol layer. In the 3-layer, connectionoriented, HDLC based COSEM profile this is the MAC sub-layer. Within this connection, the physical layer can not return to the identification stage.
NOTE 1 The basic assumption of this state machine is that any upper layer PDU (here it is the MPDU) is longer than three characters. NOTE 2 The state machine shown in Figure 6 is not complete, for example it is not indicated where the Nb_of_received_char layer parameter is set to its initial value; exit conditions and transitions from the data communications state are not shown. NOTE 3 This identification service definition ensures backward compatibility with client systems, which are not using the optional identification service. If the first message of the client is not an IDENTIFY.request but longer than three characters it shall be given to the data link layer and the identification stage is over, too.

The partial state machine for the client side physical layer is shown in Figure 7.
DISCONNECTED PH-CONNECT.ind PH-CONNECT.req IDLE Physical disconnection demanded/detected PH-CONNECT.cnf (ERROR)

Wait PH-connection PH-CONNECT.cnf(OK)

PH-ABORT.ind

Byte received PH-DATA.ind ( Byte )

CONNECTED PH-DATA.req Send byte CONNECTED

IEC

241/02

Figure 7 Partial state machine for the client side physical layer

62056-42 IEC:2002(E)

19

The client side physical layer uses a layer parameter, Destination_process, to decide where to send the data received. The layer parameter shall be managed by the layer management application process. When this parameter is not set (NULL), the physical layer shall send PHDATA.indications to the (physical connection manager) application process. When the identification phase is over, the client application shall set the destination_process parameter to point to the next upper layer of the protocol stack (the MAC sub-layer). From this moment PH-DATA.indications (and, in the case of a physical connection interruption, a copy of the PH-ABORT.indication) shall be sent to the upper protocol layer. 6.3.4 Data communications

Once the physical layer exits from the identification stage, it enters into the data communications stage, where PH-DATA.request and PH-DATA.indication services are exclusively used by the upper protocol layer, which is the data link layer IEC 62056-46. The physical layer is not responsible for any data flow control function: the data received with a PH-DATA.request shall be either transmitted immediately, or when a physical data flow control is implemented shall overwrite the previous, not yet transmitted byte. As the PHDATA.request service is neither locally nor remotely confirmed, no error shall be signalled in this latter case. 6.3.5 Disconnection of an existing physical connection

Either the client or the server can initiate the disconnection of an existing physical connection. This takes place by the physical connection manager application process invoking the PHABORT.request service, as it is shown in Figure 3. The physical layer tries to disconnect the current physical connection and informs the requestor about the result via the PH-ABORT.confirm service. The PH-ABORT.request service is always locally confirmed: the remote unit does not receive any message; it simply detects the disruption of the physical channel (e.g. the carrier is no longer available). When the client or the server detects a physical disconnection this can be the result of a PH-ABORT.request service invocation in the remote station but also due to a line error the physical layer shall indicate this event using the PH-ABORT.indication service primitive. This service primitive shall be sent not only to the physical connection manager application process but also to the next higher protocol layer. This information is necessary for the upper layers to correctly close their connections after the disruption of the physical channel.

 20

62056-42 IEC:2002(E)

Annex A (informative) An example: PH-layer service primitives and Hayes commands

A.1

General

The purpose of this annex is to describe the principles of using an intelligent modem below the physical layer interface. It is not the intention to give a complete reference of the Hayes command set or the possibilities provided by the physical layer. The Hayes command set is mainly used in the PSTN modem environment. There is a difference between the command mode and the data transmission mode. In command mode, all commands are issued with a leading "AT". This enables the modem to adapt automatically to the baud rate and line parameters on DTE/DCE side. In data transmission mode, all data is passed to the remote DCE. Data are buffered if an additional data correction or compression mode is enabled.

A.2

Physical layer services and related message exchanges

In the following subclauses the use of the various commands is explained using examples and message sequence charts. A.2.1 PH-CONNECT.request

The DTE requests to establish a physical connection with a remote DTE by transmitting the dial command together with the phone number to the DCE (ATD PhoneNumber). Example: ATD049515101188

dials the phone number 049515101188 using the default dialling mode.

Calling DTE (physical connection manager)

DTE physical layer

Calling DCE

PH-CONNECT.request ( PhConnType = PSTN, PhConnReqParams ) "ATD049515101188"

IEC

242/02

Figure A.1 MSC for physical connection request

62056-42 IEC:2002(E)

21

As it is shown, the physical layer extracts the telephone number from the PhConnReqParams service parameter, and sends it as a series of ASCII characters headed by the ATD Hayes command identifier to the DCE. No more action is required in the physical layer off hook the line, dialling and analyzing the result is done by the DCE in an autonomous way (that is why this type of modem is called intelligent). The physical layer simply waits the result of the command execution which is sent back by the DCE in the form of a Hayes message, as it is shown in Figure A.2. A.2.2 PH-CONNECT.confirm

When the DCE is in ASCII mode, it generates one of the following messages after trying to dial the previously received phone number: CONNECT: indicates that the connection has been established successfully. After issuing the connect message, the DCE switches to the data transmission mode. ERROR: indicates a general error or an invalid dial command. NO DIALTONE: indicates that there was no dial tone detected within the given timeout period. NO CARRIER: indicates that the connection has not been established because there was no carrier detected from the remote DCE. BUSY: indicates that the connection has not been established because the remote DCE is busy. When the physical layer receives any of these messages, it generates a PHCONNECT.confirm service primitive with the correct service parameters to the service user, the physical connection manager application process. Figure A.2 shows the complete message sequence at the CALLING station in case of successful physical connection establishment.

Calling DTE (physical connection manager)

DTE physical layer

Calling DCE

PH-CONNECT.request ( PhConnType = PSTN, PhConnReqParams ) "ATD049515101188" Off-hook, dial, connect "CONNECT"

PH-CONNECT.confirm ( Result = OK, PhConnCnfParams )

IEC

243/02

Figure A.2 Physical connection establishment at the CALLING station

 22 A.2.3 PH-CONNECT.indication

62056-42 IEC:2002(E)

A DCE indicates an incoming call by issuing the RING message to the DTE. If the DCE was switched to the AutoAnswer mode during the initialize procedure, it does not send RING messages, but tries to establish the connection automatically after detecting the specified number of ring signals. If the auto answer mode is disabled, the PH entity can decide whether to pick up the phone by using the "ATA" command or not. This may be applicable if the server maintains time windows to answer the phone. Messages to the DTE: RING: Indicates an incoming call. Commands to the DCE: ATA: Answer the incoming call. In both cases, the DCE signals the result in the same way as it was discussed at PHCONNECT.confirm. A simplified message sequence of a complete physical connection establishment is shown in Figure A.3, when the DCE is not working in AutoAnswer mode.
Calling DTE (physical connection manager) Called DTE (physical connection manager)

DTE physical layer

Calling DCE

PSTN

Called DCE

DTE physical layer

PH-CONNECT.request ( PhConnType=PSTN, PhConnReqParams ) "ATD049515101188"

Off-hook Dial-Tone Dialing Ring-tone Ring-tone "ATA" Off-hook

Ring Ring "RING" "RING"

PH-CONNECT.confirm ( Result = OK, PhConnCnfParams "CONNECT" )

PSTN connection is established Send carrier Send carrier "CONNECT" PH-CONNECT.indication

IEC

244/02

Figure A.3 MSC for physical connection establishment

A.2.4

PH-DATA.request / .indication

Assuming that a connection with a remote DCE was established before and that the DCE is in data transmission mode now, all data passed to the local DCE will be transmitted to the remote DCE.

62056-42 IEC:2002(E)

23

Service user application process or protocol layer

DTE physical layer

Calling DCE

PSTN

Called DCE

DTE physical layer

Service user application process or protocol layer

PH-DATA.req(DATA)

Data Data Data PH-DATA.ind(DATA) PH-DATA.req(DATA1) Data1 Data1 Data1

PH-DATA.ind(DATA1)

IEC

245/02

Figure A.4 Data exchange between the calling and called stations Please note that there is a difference between the actual data formats:

DATA/(DATA1), the service parameter of the DATA.request/indicate is specified in 6.1 as one byte.

data

communication

services

Data/(Data1) is a frame containing the data with some additional bits for the asynchronous transmission (start and stop bit). Data/(Data1), the information exchanged between the two DCEs might contain even more bits for the purpose of error detection/correction functions) and/or could be encoded for the data transmission purposes. PH-ABORT.request /.confirm

A.2.5

Before the connection can be terminated, the modem has to be switched to local command mode first. For this purpose, the Hayes environment provides an escape sequence defined as:

1 second idle state (no data transmission); sending 3 plus "+++" characters; 1 second idle state again.

The DCE confirms the command mode with an OK message (but the connection is still valid). The connection can be terminated now using the OnHook "ATH" command. Messages to the DTE: OK : DCE is in command mode again. Commands to the DCE: ATH : terminate the connection (OnHook) If the OnHook command was successful, the DCE responds with the NO_CARRIER message, otherwise an ERROR message is returned.

 24 NO_CARRIER : connection was successfully aborted. ERROR : the OnHook command failed, connection is still available. A.2.6 PH-ABORT.indication

62056-42 IEC:2002(E)

If the carrier is lost, the local DCE issues the "NO_CARRIER" message. The DTE is not able to determine the reasons for losing the carrier; one of the reasons can be that the remote DTE terminated the connection. Once the physical layer has received this message, it should use the PH-ABORT.indication service primitive to indicate the termination of the connection. NO_CARRIER : connection was aborted by the remote DCE or due an error condition. Figure A.5 shows an example for physical disconnection.
Abort requestor (physical connection manager) DCE1 PSTN DCE2 Physical connection manager

DTE physical layer

DTE physical layer

DTE data link layer

PH-ABORT.req 1 second pause "+++" 1 second pause "OK" "ATH" No carrier is sent anymore by DCE1 ON_HOOK ON_HOOK PH-ABORT.cnf (Result = OK) NO_CARRIER "ATH" ON_HOOK "OK" PH-ABORT.ind() PH-ABORT.ind() "NO_CARRIER"

IEC

246/02

Figure A.5 MSC for a physical disconnection

62056-42 IEC:2002(E)

25

Annex B (informative) Data model and protocol

The data model uses generic building blocks to define the complex functionality of the metering equipment. It provides a view of this functionality of the meter as it is available at its interface(s). The model does not cover internal, implementation-specific issues. The communication protocol defines how the data can be accessed and exchanged. This is illustrated in Figure B.1 below:

1. Modeling

COSEM Interface Objects

Register Attribute(s) 1. logical_name 2. value 3. scaler-unit Method(s) 1. reset

(static) (dyn.) (static)

n ti o a ci so Version=0 0..n Class_id=3, s Data Type Min A Max Def octet-string er instance specific s scal_unit_type U S m/o M o DL

Protocol Services to access attributes and methods 2. Messaging

Communication Protocol

Messages: Service_Id( Class_Id, Instance_Id, Attribute_Id/Method_Id ) Encoding: (APDU) C0 01 00 03 01 01 01 08 00 FF 02

3. Transporting

O IS

C IE

,..

IEC

247/02

Figure B.1 The three-step approach of COSEM

The COSEM specification details metering domain specific interface classes. The functionality of the meter is defined by the instances of these interface classes, called COSEM objects. This is defined in IEC 62056-62. Logical names, identifying the COSEM objects are defined in IEC 62056-61. The attributes and methods of these COSEM objects can be accessed and used via the messaging services of the application layer. The lower layers of the protocol transport the information.

 26

62056-42 IEC:2002(E)

Bibliography
IEC 62056-41:1998, Electricity metering Data exchange for meter reading, tariff and load control Part 41: Data exchange using wide area networks: Public switched telephone network (PSTN) with LINK+ protocol IEC 61334-4-41:1996, Distribution automation using distribution line carrier systems Part 4: Data communication protocols Section 41: Application protocols Distribution line message specification IEC 61334-6:2000, Distribution automation using distribution line carrier systems Part 6: A-XDR encoding rule ISO 2110:1989, Information technology Data communication 25-pole DTE/DCE interface connector and contact number assignments ITU-T V.24:2000, List of definitions for interchange circuits between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) ITU-T V.25:1996, Automatic answering equipment and general procedures for automatic calling equipment on the general switched telephone network ITU-T V.25bis:1996, Synchronous and asynchronous automatic dialling procedures on switched networks ITU-T V.28:1993, Electrical characteristics for unbalanced double-current interchange circuits ITU-T X.211:1995, Information technology Open Systems Interconnection Physical service definition

62056-42 IEC:2002(E)

27

Index
abbreviations ........................................... 6 ATA ....................................................... 22 ATH ....................................................... 23 BUSY..................................................... 21 client........................................................ 6 Client side ............................................. 18 CONNECT ............................................. 21 Connection establishment ........................ 8 COSEM ................................................... 6 Data communication services................... 8 Data Communications ............................ 19 Data model ............................................ 25 DCE......................................................... 6 definitions ................................................ 6 description of the procedures ................. 13 Disconnection of an existing Physical Connection ......................................... 19 ERROR............................................ 21, 24 Identification Service ............................. 17 Identification Service message specification ....................................... 15 Identification service protocol specification ........................................................... 17 Identify.request ...................................... 15 Identify.response ................................... 16 Layer management services .................... 8 List of services......................................... 8 master ..................................................... 6 message exchanges .............................. 20 NO CARRIER ........................................ 21 NO DIALTONE....................................... 21 NO_CARRIER........................................ 24 Normative references............................... 5 OK..........................................................23 Overview ................................................. 7 Partial state machine ..............................18 PH-ABORT.confirm ................................11 PH-ABORT.indication .......................11, 24 PH-ABORT.request ................................11 PH-ABORT.request /.confirm ..................23 PH-CONNECT.confirm .....................10, 21 PH-CONNECT.indication ..................10, 22 PH-CONNECT.request .......................9, 20 PH-DATA.indication................................12 PH-DATA.request ...................................12 PH-DATA.request / .indication ................22 PH-Layer service primitives and Hayes command set.......................................20 Physical layer operation .........................13 Physical Layer Protocol Data Unit...........13 physical layer services ............................ 9 Physical layer services ...........................20 Protocol Data Unit ..................................13 Protocol Specification .............................13 release related services........................... 8 RING ......................................................22 server ...................................................... 6 Server side .............................................17 Service definitions ................................... 9 Service Specification ............................... 8 Setting up a physical connection ............14 slave ....................................................... 6 Terms...................................................... 6 The Identification Service .......................15 Transmission order and characteristics...13

___________

Standards Survey

The IEC would like to offer you the best quality standards possible. To make sure that we continue to meet your needs, your feedback is essential. Would you please take a minute to answer the questions overleaf and fax them to us at +41 22 919 03 00 or mail them to the address below. Thank you!

Customer Service Centre (CSC) International Electrotechnical Commission 3, rue de Varemb 1211 Genve 20 Switzerland or Fax to: IEC/CSC at +41 22 919 03 00

Thank you for your contribution to the standards-making process.

Nicht frankieren Ne pas affranchir

Prioritaire
Non affrancare No stamp required

RPONSE PAYE SUISSE

Customer Service Centre (CSC) International Electrotechnical Commission 3, rue de Varemb 1211 GENEVA 20 Switzerland

Q1

Please report on ONE STANDARD and ONE STANDARD ONLY . Enter the exact number of the standard: (e.g. 60601-1-1) .............................................................

Q6

If you ticked NOT AT ALL in Question 5 the reason is: (tick all that apply) standard is out of date 4 standard is incomplete 4 standard is too academic 4 standard is too superficial 4 title is misleading 4 I made the wrong choice 4 other ....................................................

Q2

Please tell us in what capacity(ies) you bought the standard (tick all that apply). I am the/a: purchasing agent 4 librarian 4 researcher 4 design engineer 4 safety engineer 4 testing engineer 4 marketing specialist 4 other.....................................................

Q7

Q3

I work for/in/as a: (tick all that apply) manufacturing 4 consultant 4 government 4 test/certification facility 4 public utility 4 education 4 military 4 other..................................................... Q8

Please assess the standard in the following categories, using the numbers: (1) unacceptable, (2) below average, (3) average, (4) above average, (5) exceptional, (6) not applicable timeliness ............................................. quality of writing.................................... technical contents................................. logic of arrangement of contents .......... tables, charts, graphs, figures ............... other ....................................................

I read/use the: (tick one) French text only English text only both English and French texts

Q4

This standard will be used for: (tick all that apply) general reference 4 product research 4 product design/development 4 specifications 4 tenders 4 quality assessment 4 certification 4 technical documentation 4 thesis 4 manufacturing 4 other.....................................................

4 4 4

Q9

Please share any comment on any aspect of the IEC that you would like us to know: ............................................................ ............................................................ ............................................................ ............................................................ ............................................................ ............................................................ ............................................................ ............................................................ ............................................................ ............................................................ ............................................................ ............................................................

Q5

This standard meets my needs: (tick one) not at all nearly fairly well exactly

4 4 4 4

ISBN 2-8318-6157-8

-:HSMINB=][VZ\^:
ICS 91.140.50; 35.100.10
Typeset and printed by the IEC Central Office GENEVA, SWITZERLAND