Scribd Logo
Upload

Welcome to Scribd!

  • 270 views

    Dynatron Instructions

    Uploaded by

    budzak2
    This document provides instructions for assembling a free energy generator with the following key points: 1) It describes the primary components including a high voltage power supply between 100-200 watts, a high frequency resonant circuit with coils L1 and L2 in a 1:4 ratio of lengths, high voltage diodes to rectify the output, and contour capacitors to form the resonant circuit. 2) It provides details on constructing the coils L1 and L2 with appropriate wire gauges and number of turns, as well as capacitor types that can withstand impulse currents from discharge. 3) A schematic diagram of the converter is shown using high voltage diodes VD1 and VD2, and

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Dynatron Instructions

    Uploaded by

    budzak2
    270 views7 pages
    This document provides instructions for assembling a free energy generator with the following key points: 1) It describes the primary components including a high voltage power supply between 100-200 watts, a high frequency resonant circuit with coils L1 and L2 in a 1:4 ratio of lengths, high voltage diodes to rectify the output, and contour capacitors to form the resonant circuit. 2) It provides details on constructing the coils L1 and L2 with appropriate wire gauges and number of turns, as well as capacitor types that can withstand impulse currents from discharge. 3) A schematic diagram of the converter is shown using high voltage diodes VD1 and VD2, and

    Original Title

    Dynatron Instructions (1)

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for assembling a free energy generator with the following key points: 1) It describes the primary components including a high voltage power supply between 100-200 watts, a high frequency resonant circuit with coils L1 and L2 in a 1:4 ratio of lengths, high voltage diodes to rectify the output, and contour capacitors to form the resonant circuit. 2) It provides details on constructing the coils L1 and L2 with appropriate wire gauges and number of turns, as well as capacitor types that can withstand impulse currents from discharge. 3) A schematic diagram of the converter is shown using high voltage diodes VD1 and VD2, and

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    270 views7 pages

    Dynatron Instructions

    Uploaded by

    budzak2
    This document provides instructions for assembling a free energy generator with the following key points: 1) It describes the primary components including a high voltage power supply between 100-200 watts, a high frequency resonant circuit with coils L1 and L2 in a 1:4 ratio of lengths, high voltage diodes to rectify the output, and contour capacitors to form the resonant circuit. 2) It provides details on constructing the coils L1 and L2 with appropriate wire gauges and number of turns, as well as capacitor types that can withstand impulse currents from discharge. 3) A schematic diagram of the converter is shown using high voltage diodes VD1 and VD2, and

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 7

    Instructions for assembly free energy generator.

    Part 1 components and materials 1) High Voltage Power Supply 3000V 100 - 200 watts. You can use transformers for neon lamps, or any similar amateur design with a high conversion efficiency and stabilization of the output current. A possible embodiment of the transducer assemblies

    1) 1) High-frequency resonant system L1 / L2 Coil L1 dangle high quality audio cable sechenirem 6.10 mm2, a homemade orlitz by appropriate cross-section. Approximate length of the conclusionsobtained litz (audio) - approximately 2 meters. Coiling is performed on the pipe kanlizatsionnoy 50 mm, number of turns 4-5 (left-coiling). The remaining conclusions of the coil is not brezaem and conclude by mid-pipeto connect to the surge of the primary loop and capacitors. Available variants

    Secondary coil L2 of the resonant circuit is performed bare copper (preferablysilverplated, tinned worse) wire with a diameter of 2-3 mm. Diameter ofwinding the secondary coil is about 75mm. The coil tap is performed from the middle. Both halves have the same winding direction (clockwise, ie right). Approximate number of coil turns, 2x16, 2h18 turns. Coil must perform an airversion with mounting holes in the 4.3-fixing brackets. Mounting kotuschek should not allow runoff vyokochastotnyh high charges onany other part of the scheme and design. Conclusions coils clamped inEnclosures placed on the mounting plate for connection of other earthlyelements of the scheme. Ratio of the lengths of wire coils L1 to L2 1 to 4,including the length vyvov connection to circuit elements. A possible embodiment of the coil vtorinoy

    High-voltage diodes (pillars) You can use store bought or make your own. Diodes of each arm must have current rating of at least 10 amperes at a reverse voltage of 25-30 kV Parallel connection of several columns to provide the required current. Version of the high diode:

    Contour capacitors (for coils L1, L2) Kondenysator circuit of the primary is chosen to work nepryazhenie at least 4kV, the capacitance depends on the frequency of the secondary circuit (the author of 28 nanofarads at the resonant frequency of 600 kilohertz). Capacitor must have a minimum dielectric loss and keep Soline power (kvar) Usually typed composite capacitor bank and a low-power. The most appropriate types of kondensaktorov - K78-2, k78-15 k78-25 or other similar well able to withstand impulse currentsof the discharge. - The secondary condenser. It is best to use capacitors of the above types but with a voltage of not less than 10 kilovolts. Excellent work Capacitors KVI-3 type, and even better-K15-U2. Secondary katuschka with the capacity of the capacitor form a resonant circuit.The capacitance of the secondary zayisit the desired resonant frequency (the author - 10 kV capacitor kvi3 2200 pF). Photos of the condenser of the secondary :

    High-frequency inductor with a minimum recuperation passage capacity Olrientirovochnaya inductor 100 - 200 uH. Variants with sectioning obmotkok.Wire diameter, 1.5-2mm in enamel izolitsii. Photo options throttle.

    choke dangle on PVC 50-75mm mandrel. Battery storage capacitors You can apply a voltage capacitors 5-15 kV with total capacity of about 2microfarads. Suitable oil-filled capacitors, all types of type-1 k41, K75-53 and other ..

    The scheme of the converter

    Diodes VD1, VD2 - high poles. Diode ultrafast VD5-1200-150 volt30 amps. Drosse5l L3 anyone with a non-closed magnetic core wire (bus) at least 6mm2,5.1 mH inductive .. Load (inverter or a dc motor) use of low input voltage 12-110 volts (voltagenirzhe more energy out)

    To be continued ...

    You might also like