LND-7330757468@CS

KISSsoft - Release 03-2011G

File Name : CylGearPair 6 (Helical DIN3990) Description: KISSsoft example Changed by : DELL_2 on: 04.05.2013

at: 18:01:42

Important hint: At least one warning has occurred during the calculation: 1-> Profile modification: The value for the tip relief is probably too small! Change the type of profile modification to 'None' in the dialog 'Define details of strength' ! 2-> Gear 2: Notch parameter qs (0.997675) outside RANGE (1.0...8.0). Please consult part 3 of the standard. YS is calculated with qs = 1.000000. 3-> Remark concerning pair 0-1: The relative structure coefficient X_WrelT is probably wrong (see dialog 'Define details of strength'). This coefficient has some influence on the safety against scuffing. Recommended values: Nitrided steel: X_relT = 1.5 Heat-treatable and case-hardening steel: X_relT = 1.0 4-> Notice concerning gear 1: Dimension over balls is not measurable (Tooth width is too small)! 5-> Notice concerning gear 2: Dimension over balls is not measurable (Tooth width is too small)!

CALCULATION OF A HELICAL GEAR PAIR

Drawing or article number: Gear 1: 0.000.0 Gear 2: 0.000.0 Calculation method DIN 3990 Method B ------- GEAR 1 -------- GEAR 2 -Power (kW) Speed (1/min) Torque (Nm) Application factor Required service life Gear driving (+) / driven (-) 1. TOOTH GEOMETRY AND MATERIAL (Geometry calculation according ISO 21771) Center distance (mm) Centre distance tolerance Normal module (mm) Pressure angle at normal section () Helix angle at reference circle () Number of teeth Facewidth (mm) Hand of gear Accuracy grade Inner diameter (mm) Inner diameter of gear rim (mm) Material Gear 1: Gear 2: [a] [mn] [alfn] [beta] [z] [b] [Q-DIN3961] [di] [dbi] ------- GEAR 1 -------- GEAR 2 -65.000 ISO 286 Measure js7 2.5000 20.0000 14.0000 11 41 18.00 18.00 left right 6 6 0.00 0.00 0.00 0.00 steel, case-hardened core strength >=25HRC Jominy J=12mm<HRC28 steel, case-hardened core strength >=25HRC Jominy J=12mm<HRC28 ------- GEAR 1 -------- GEAR 2 -HRC 61 HRC 61 430.00 1500.00 430.00 1500.00 [P] [n] [T] [KA] [H] 2000.0 59.7 + 12.500 1.25 20000.00 536.6 222.5 -

18CrNiMo7-6, Case-carburized ISO 6336-5 Figure 9/10 (MQ), 18CrNiMo7-6, Case-carburized ISO 6336-5 Figure 9/10 (MQ),

Surface hardness Fatigue strength. tooth root stress (N/mm) [sigFlim] Fatigue strength for Hertzian pressure (N/mm) [sigHlim]

1/7

Tensile strength (N/mm) Yield point (N/mm) Young's modulus (N/mm) Poisson's ratio Average roughness, Ra, tooth flank (m) Mean roughness height, Rz, flank (m) Mean roughness height, Rz, root (m)

[Rm] [Rp] [E] [ny] [RAH] [RZH] [RZF]

1200.00 850.00 206000 0.300 0.60 4.80 20.00

1200.00 850.00 206000 0.300 0.60 4.80 20.00

Tool or reference profile of gear 1 : Reference profile 1.25 / 0.38 / 1.0 ISO 53.2 Profil A Addendum coefficient [haP*] Dedendum coefficient [hfP*] Tip radius factor [rhoaP*] Root radius factor [rhofP*] Tip form height coefficient [hFaP*] Protuberance height factor [hprP*] Protuberance angle [alfprP] Ramp angle [alfKP] Tool or reference profile of gear 2 : Reference profile 1.25 / 0.38 / 1.0 ISO 53.2 Profil A Addendum coefficient [haP*] Dedendum coefficient [hfP*] Tip radius factor [rhoaP*] Root radius factor [rhofP*] Tip form height coefficient [hFaP*] Protuberance height factor [hprP*] Protuberance angle [alfprP] Ramp angle [alfKP] Summary of reference profile gears: Dedendum reference profile (module) [hfP*] Tooth root radius Refer. profile (module) [rofP*] Addendum Reference profile (module) [haP*] Protuberance height (module) [hprP*] Protuberance angle () [alfprP] Buckling root flank height (module) [hFaP*] Buckling root flank angle () [alfKP] Data for Grinding / Honing: Depth of immersion (module) [hgrind*] Radius at cutter head (module) [rgrind*] Type of profile modification: Tip relief (m)

not topping

1.000 1.250 0.000 0.380 0.000 0.000 0.000 0.000

not topping 1.250 0.380 1.000 0.000 0.000 0.000 0.000 1.038 0.100

1.000 1.250 0.000 0.380 0.000 0.000 0.000 0.000

1.250 0.380 1.000 0.000 0.000 0.000 0.000 1.066 0.100

for high load capacity gearboxe [Ca] 5.00 oil bath lubrication Oil: Mobilgear 600 XP 150 Mineral-oil base [nu40] 150.00 [nu100] 14.70 [FZGtestA] 12 [roOil] 0.890 [TS] 70.000

5.00

Lubrication type Type of oil Lubricant base Kinem. viscosity oil at 40 C (mm/s) Kinem. viscosity oil at 100 C (mm/s) FZG-Test A/8.3/90 (ISO 14635-1) Specific density at 15 C (kg/dm) Oil temperature (C) Overall transmission ratio Gear ratio Transverse module (mm) Pressure angle at pitch circle () Working transverse pressure angle ()

[itot] [u] [mt] [alft] [alfwt] [alfwt.e/i] Working pressure angle at normal section () [alfwn] Helix angle at operating pitch circle () [betaw] Base helix angle () [betab] Reference centre distance (mm) [ad] Sum of profile shift coefficients [Summexi] Profile shift coefficient [x] Tooth thickness (Arc) (module) [sn*] Tip alteration (mm) Reference diameter (mm) Base diameter (mm) Tip diameter (mm) (mm) Tip diameter allowances (mm) Tip chamfer / tip rounding (mm) Tip form diameter (mm) (mm) [k*mn] [d] [db] [da] [da.e/i] [Ada.e/i] [hK] [dFa] [dFa.e/i]

------- GEAR 1 -------- GEAR 2 --3.727 3.727 2.577 20.562 15.213 15.261 / 15.164 14.805 13.600 13.140 66.990 -0.7017

0.2971 1.7871 -0.236 28.342 26.536 34.355 34.355 / 34.345 0.000 / -0.010 0.000 34.355 34.355 / 34.345

-0.9988 0.8438

-0.236 105.638 98.908 105.172 105.172 / 105.162 0.000 / -0.010 0.000 105.172 105.172 / 105.162

2/7

Active tip diameter (mm)

[dNa] 34.355 104.617 (mm) [dNa.e/i] 34.355 / 34.345 104.599 / 104.501 Operating pitch diameter (mm) [dw] 27.500 102.500 (mm) [dw.e/i] 27.506 / 27.494 102.524 / 102.476 Root diameter (mm) [df] 23.577 94.394 Generating Profile shift coefficient [xE.e/i] 0.2729 / 0.2619 -1.0317 / -1.0537 Manufactured root diameter with xE (mm) [df.e/i] 23.456 / 23.401 94.229 / 94.119 Theoretical tip clearance (mm) [c] 0.625 0.625 Effective tip clearance (mm) [c.e/i] 0.783 / 0.693 0.733 / 0.671 Active root diameter (mm) [dNf] 26.536 99.669 (mm) [dNf.e/i] 26.538 / 26.537 99.685 / 99.655 Root form diameter (mm) [dFf] 26.536 99.285 (mm) [dFf.e/i] 26.538 / 26.537 99.246 / 99.220 Reserve (dNf-dFf)/2 (mm) [cF.e/i] 0.000 / -0.000 0.232 / 0.205 Addendum (mm) [ha = mn * (haP*+x)] 3.007 -0.233 (mm) [ha.e/i] 3.007 / 3.002 -0.233 / -0.238 Dedendum (mm) [hf = mn * (hfP*-x)] 2.382 5.622 (mm) [hf.e/i] 2.443 / 2.470 5.704 / 5.759 Roll angle at dFa () [xsi_dFa.e/i] 47.112 / 47.078 20.712 / 20.695 Roll angle to dNa () [xsi_dNa.e/i] 47.112 / 47.078 19.714 / 19.538 Roll angle to dNf () [xsi_dNf.e/i] 0.587 / 0.425 7.196 / 7.055 Roll angle at dFf () [xsi_dFf.e/i] 0.587 / 0.425 4.737 / 4.556 Tooth height (mm) [H] 5.389 5.389 Virtual gear no. of teeth [zn] 11.955 44.558 Normal tooth thickness at tip cyl. (mm) [san] 1.467 2.267 (mm) [san.e/i] 1.422 / 1.390 2.210 / 2.167 Normal spacewidth at root cylinder (mm) [efn] 0.000 0.000 (mm) [efn.e/i] 0.000 / 0.000 0.000 / 0.000 Max. sliding velocity at tip (m/s) [vga] 1.940 0.955 Specific sliding at the tip [zetaa] 0.849 0.997 Specific sliding at the root [zetaf] -349.763 -5.616 Sliding factor on tip [Kga] 0.674 0.332 Sliding factor on root [Kgf] -0.332 -0.674 Pitch on reference circle (mm) [pt] 8.094 Base pitch (mm) [pbt] 7.579 Transverse pitch on contact-path (mm) [pet] 7.579 Lead height (mm) [pz] 357.115 1331.063 Axial pitch (mm) [px] 32.465 Length of path of contact (mm) [ga, e/i] 10.897 (10.812 / 10.767) Length T1-A, T2-A (mm) [T1A, T2A] 0.013( 0.098/ 0.135) 17.043(16.901/16.978) Length T1-B (mm) [T1B, T2B] 3.331( 3.331/ 3.323) 13.725(13.668/13.790) Length T1-C (mm) [T1C, T2C] 3.608( 3.596/ 3.620) 13.448(13.403/13.493) Length T1-D (mm) [T1D, T2D] 7.592( 7.676/ 7.714) 9.465( 9.323/ 9.399) Length T1-E (mm) [T1E, T2E] 10.910(10.910/10.902) 6.146( 6.089/ 6.211) Length T1-T2 (mm) [T1T2] 17.056 (16.999 / 17.113) Diameter of single contact point B (mm) [d-B] 27.360(27.360/27.356) 102.647(102.616/102.682) Diameter of single contact point D (mm) [d-D] 30.573(30.658/30.696) 100.703(100.650/100.679) Addendum contact ratio [eps] 0.963( 0.965/ 0.961) 0.474( 0.462/ 0.460) Minimal length of contact line (mm) [Lmin] 18.484 Transverse contact ratio Transverse contact ratio with allowances Overlap ratio Total contact ratio Total contact ratio with allowances 2. FACTORS OF GENERAL INFLUENCE Nominal circum. force at pitch circle (N) ------- GEAR 1 -------- GEAR 2 -4211.7 1050.1 1579.8 4619.2 233.98 4340.6 1050.1 1180.4 2.97 0.6 0.6 0.800 1.000 0.975 1.000 10.678 14.185 0.00280 [eps_a] [eps_a.e/m/i] [eps_b] [eps_g] [eps_g.e/m/i] 1.438 1.427 / 1.424 / 1.421 0.554 1.992 1.981 / 1.978 / 1.975

[Ft] Axial force (N) [Fa] Radial force (N) [Fr] Normal force (N) [Fnorm] Tangent.load at p.c.d.per mm (N/mm) (N/mm) [w] Only as information: Forces at operating pitch circle: Nominal circumferential force (N) [Ftw] Axial force (N) [Faw] Radial force (N) [Frw] Circumferential speed pitch d.. (m/sec) [v] Running-in value (m) Running-in value (m) Correction coefficient Gear body coefficient Reference profile coefficient Material coefficient Singular tooth stiffness (N/mm/m) Meshing stiffness (N/mm/m) Reduced mass (kg/mm) [yp] [yf] [CM] [CR] [CBS] [E/Est] [c'] [cg] [mRed]

3/7

Resonance speed (min-1) [nE1] Nominal speed (-) [N] Subcritical range Running-in value (m) [ya] Bearing distance l of pinion shaft (mm) [l] Distance s of pinion shaft (mm) [s] Outside diameter of pinion shaft (mm) [dsh] Load according DIN 3990/1 Figure 6.8 [-] (0:6.8a, 1:6.8b, 2:6.8c, 3:6.8d, 4:6.8e) coefficient K' according to DIN 3990/1 diagram 6.8 [K'] Without support effect Tooth trace deviation (active) (m) [Fby] from deformation of shaft (m) [fsh*B1] Tooth trace: width-crowned [Cbeta = 0.5*(fma+fsh)] Position of Contact pattern: favorable from production tolerances (m) [fma*B2] Tooth trace deviation, theoretical (m) [Fbx] Running-in value (m) [yb] Dynamic factor Width factor flank - Tooth root - Scuffing [KV] [KHb] [KFb] [KBb] [KHa] [KFa] [KBa] [Kbg] [NL] 2400.000

61811 0.032 0.3 36.000 3.600 18.000 4 -1.00 4.38 0.81 4.00 5.15 0.8 1.012 1.105 1.074 1.105 1.000 1.000 1.000 1.000 643.902

Transverse coefficient - flank - Tooth root - Scuffing Helix angle coefficient scuffing Number of load changes (in mio.) 3. TOOTH ROOT STRENGTH

------- GEAR 1 -------- GEAR 2 -Calculation of Tooth form coefficients according method: B (Calculate tooth shape coefficient YF with addendum mod. x) Tooth form factor [YF] 1.44 2.55 Stress correction factor [YS] 2.00 1.38 Working angle () [alfen] 20.66 13.99 Bending lever arm (mm) [hF] 2.31 3.17 Tooth thickness at root (mm) [sFn] 4.90 4.39 Tooth root radius (mm) [roF] 1.22 2.20 (hF* = 0.926/1.266 sFn* = 1.959/1.755 roF* = 0.489/0.880 dsFn = 24.34/95.89 alfsFn = 30.00/30.00) Contact ratio factor [Yeps] Helix angle factor [Ybet] Effective facewidth (mm) [beff] Nominal shear stress at tooth root (N/mm) [sigF0] Tooth root stress (N/mm) [sigF] Permissible bending stress at root of Test-gear Support factor [YdrelT] Surface factor [YRrelT] Size coefficient (Tooth root) [YX] Finite life factor [YNT] [YdrelT*YRrelT*YX*YNT] Alternating bending coefficient [YM] Stress correction factor [Yst] Limit strength tooth root (N/mm) [sigFG] Permissible tooth root stress (N/mm) [sigFP=sigFG/SFmin] Required safety [SFmin] Safety for Tooth root stress [SF=sigFG/sigF] Transmittable power (kW) [kWRating] 4. SAFETY AGAINST PITTING (TOOTH FLANK) Zone factor [ZH] Elasticity coefficient (N^.5/mm) [ZE] Contact ratio factor [Zeps] Helix angle factor [Zbet] Effective facewidth (mm) [beff] Nominal flank pressure (N/mm) [sigH0] Surface pressure at operating pitch circle (N/mm) [sigHw] Single tooth contact factor [ZB,ZD] ------- GEAR 1 -------- GEAR 2 -2.858 189.812 0.875 0.985 18.00 1513.64 1.01 1789.45 1.00 1.000 0.935

18.00 252.00 342.32 0.995 0.957 1.000 1.000 0.952 1.000 818.78 584.84 1.40 2.39 21.36

18.00 307.64 417.91 0.983 0.957 1.000 1.000 0.941 1.000 809.15 577.97 1.40 1.94 17.29

2.00

4/7

Flank pressure (N/mm) Lubrication factor Speed factor Roughness factor Material mating factor Finite life factor

[sigH]

1813.51 0.992 0.971 0.952 1.000 1.000 0.917 0 1.000 1376.04 1376.04 0.77 1.00 7.20 0.76 0.58

1789.45 0.992 0.971 0.952 1.000 1.000 0.917 0 1.000 1376.04 1376.04 0.77 1.00 7.39 0.77 0.59

[ZL] [ZV] [ZR] [ZW] [ZNT] [ZL*ZV*ZR*ZNT] Small amount of pitting permissible (0=no, 1=yes) Size coefficient (flank) [ZX] Limit strength pitting (N/mm) [sigHG] Permissible surface pressure (N/mm) [sigHP=sigHG/SHmin] Safety for surface pressure at operating pitch circle [SHw] Required safety [SHmin] Transmittable power (kW) [kWRating] Safety for stress at single tooth contact [SHBD=sigHG/sigH] (Safety regarding nominal torque) [(SHBD)^2] 4b. MICROPITTING ACCORDING TO ISO/TR 15144-1:2010

Calculation of permissible specific film thickness Lubricant load according to FVA Info sheet 54/7 10 (Oil: Mobilgear 600 XP 150) Reference data FZG-C Test T1 =265.1 Nm, theM=106.4 , theB =219.6 h =0.064 m, WW = 1.00 , lamGFT=0.127 Permissible specific film thickness (m) [lamGFP] 0.178 Intermediate result according to ISO TR 15144: mym =0.133 , XL =1.000 , XR=1.481 the0 = 91.1 , XCa =1.000 , HV=0.266 Er =226373.6 N/mm, etatM = 15.6 , Ra= 0.6 m Ceq1 = 5.0 m, Ceq2 = 5.0 m, Ceff = 20.6 m Calculation of speeds, load distribution and flank curvature according to ISO15144 method B Minimal specific film thickness (m) [lamGFY] 0.001 (hY=0.001 m) Safety against micropitting [Slam] 0.008 (For intermediate results refer to file: Micropitting_12.tmp) 5. STRENGTH AGAINST SCUFFING Calculation method according DIN3990 1.000 13.795 5.00 1.500 20.62 18.000 327.018 50.002 0.474 145.69 161.04 522.88 1.104 306.72 0.442 1.000 4.72 0.174 2.000 1.913 106.91 52.73 522.88 0.266 32.16 0.129 0.782 1.000 1.067 13.795 5.00

Lubrication coefficient (for lubrication type) [XS] Relative structure coefficient (Scuffing) [XWrelT] Thermal contact factor (N/mm/s^.5/K) [BM] Relevant tip relief (m) [Ca] Optimal tip relief (m) [Ceff] Effective facewidth (mm) [beff] Applicable circumferential force/facewidth (N/mm) [wBt] Flash factor (K*N^-.75*s^.5*m^-.5*mm) [XM] Pressure angle factor (eps1: 0.898, eps2: 0.963) [Xalfbet] Flash temperature-criteria Tooth mass temperature (C) [theM-B] theM-B = theoil + XS*0.47*theflamax [theflamax] Scuffing temperature (C) [theS] Coordinate gamma (point of highest temp.) [Gamma] [Gamma.A]= -0.996 [Gamma.E]= 2.024 Highest contact temp. (C) [theB] Geometry factor [XB] Load sharing factor [XGam] Dynamic viscosity (mPa*s) [etaM] Coefficient of friction [mym] Required safety [SBmin] Safety factor for scuffing (flash-temp) [SB] Integral temperature-criteria Tooth mass temperature (C) theM-C = theoil + XS*0.70*theflaint Integral scuffing temperature (C) Contact ratio factor Dynamic viscosity (mPa*s) Averaged coefficient of friction Geometry factor Meshing factor Tip relief factor [theM-C] [theflaint] [theSint] [Xeps] [etaOil] [mym] [XBE] [XQ] [XCa]

5/7

Integral tooth flank temperature (C) [theint] Required safety [SSmin] Safety factor for scuffing (intg.-temp.) [SSint] Safety referring to transferred torque [SSL] 6. MEASUREMENTS FOR TOOTH THICKNESS Tooth thickness deviation Tooth thickness allowance (normal section) (mm) [As.e/i] Number of teeth spanned Base tangent length (no backlash) (mm) Actual base tangent length ('span') (mm) Diameter of contact point (mm) [k] [Wk] [Wk.e/i] [dMWk.m]

186.01 1.800 2.811 3.904

------- GEAR 1 -------- GEAR 2 -DIN3967 d24 DIN3967 d25 -0.044 / -0.064 2.000 11.998 11.957 / 11.938 28.975 -0.060 / -0.100 3.000 18.307 18.251 / 18.213 100.489 4.210 4.250 52.955 52.827 / 52.738 100.500 105.836 105.580 / 105.402 105.911 105.654 / 105.476 105.911 105.654 / 105.476 2.109 2.049 / 2.009 -0.225 2.109 2.049 / 2.009 / 64.688

Theoretical diameter of ball/pin (mm) [DM] 5.060 Eff. Diameter of ball/pin (mm) [DMeff] 5.250 Theor. dim. centre to ball (mm) [MrK] 18.981 Actual dimension centre to ball (mm) [MrK.e/i] 18.945 / 18.928 Diameter of contact point (mm) [dMMr.m] 29.939 Diametral measurement over two balls without clearance (mm) [MdK] 37.629 Actual dimension over balls (mm) [MdK.e/i] 37.557 / 37.524 Theor. dimension over two pins (mm) [MdR] 37.962 Actual dimension over rolls (mm) [MdR.e/i] 37.889 / 37.856 Dimensions over 3 pins without clearance (mm) [Md3R] 37.962 Actual dimensions over 3 rolls (mm) [Md3R.e/i] 37.889 / 37.856 Chordal tooth thickness (no backlash) (mm) ['sn] Actual chordal tooth thickness (mm) ['sn.e/i] Reference chordal height from da.m (mm) [ha] Tooth thickness (Arc) (mm) [sn] (mm) [sn.e/i] Backlash free center distance (mm) [aControl.e/i] Backlash free center distance, allowances (mm) [jta] Centre distance allowances (mm) [Aa.e/i] Circumferential backlash from Aa (mm) [jt_Aa.e/i] Radial clearance (mm) [jr] Circumferential backlash (transverse section) (mm) [jt] Torsional angle using fixed values gear 1 () Normal backlash (mm) [jn] 7. GEAR ACCURACY According DIN 3961: Accuracy grade Profile form deviation (m) Profile slope deviation (m) Total profile deviation (m) Helix form deviation (m) Helix slope deviation (m) Total helix deviation (m) Normal base pitch deviation (m) Single pitch deviation (m) Difference between adjacent pitches (m) Total cumulative pitch deviation (m) Cumulative circular pitch deviation over 4.451 4.407 / 4.387 3.170 4.468 4.424 / 4.404 64.805

-0.195 / -0.312 0.015 / -0.015 0.008 / -0.008 0.327 / 0.180 0.172 / 0.096 0.1867 /0.1040 0.157 / 0.087

------- GEAR 1 -------- GEAR 2 -6 8.00 6.00 10.00 4.00 8.00 9.00 7.00 7.00 9.00 21.00 13.00 16.00 9.00 19.00 8.00 25.00 12.00 8.00 22.00 11.05 5.00 21.00 6 8.00 6.00 10.00 4.00 8.00 9.00 8.00 8.00 10.00 27.00 17.00 19.00 11.00 22.00 9.00 30.00 13.00 10.00 28.00 11.05 5.00 28.00

[Q-DIN3961] [ff] [fHa] [Ff] [ffb] [fHb] [Fb] [fpe] [fp] [fu] [Fp] z/8 pitches (m) [Fpz/8] Concentricity deviation (m) [Fr] Tooth Thickness Variation (m) [Rs] Total radial composite deviation (m) [Fi"] Radial tooth-to-tooth composite deviation (m) [fi"] Total tangential composite deviation (m) [Fi'] Tangential tooth-to-tooth composite deviation (m) [fi'] According DIN 58405 (Precision Mechanics): Tooth-to-tooth composite error (m) [fi"] Composite error (m) [Fi"] Axis alignment error (m) [fp] Flank direction error (m) [fbeta] Concentricity deviation (m) [Trk, Fr]

6/7

Tolerance for alignment of axes (recommendation acc. ISO/TR 10064, Quality 6) Maximum value for deviation error of axis (m) [fSigbet] 11.17 Maximum value for inclination error of axes (m) [fSigdel] 22.35 8. ADDITIONAL DATA Maximal possible centre distance (eps_a=1.0) [aMAX] 65.949 Torsional stiffness (MNm/rad) [cr] 0.0 Mean coeff. of friction (acc. Niemann) [mum] 0.128 Wear sliding coef. by Niemann [zetw] 1.291 Power loss from gear load (kW) [PVZ] 0.425 (Meshing efficiency (%) [etaz] 96.600) Weight - calculated with da (kg) [Mass] 0.131 Moment of inertia (System referenced to wheel 1): calculation without consideration of the exact tooth shape single gears ((da+df)/2...di) (kgm) [TraeghMom] 9.638e-006 System ((da+df)/2...di) (kgm) [TraeghMom] 0.0001079 9. DETERMINATION OF TOOTHFORM Profile and tooth trace modifications for gear 1 Symmetric (both flanks) - Tip relief, linear Caa = 5.000m Profile and tooth trace modifications for gear 2 Symmetric (both flanks) - Tip relief, linear Caa = 5.000m Data for the tooth form calculation : Data not available. REMARKS: - Specifications with [.e/i] imply: Maximum [e] and Minimal value [i] with consideration of all tolerances Specifications with [.m] imply: Mean value within tolerance - For the backlash tolerance, the center distance tolerances and the tooth thickness deviation are taken into account. Shown is the maximal and the minimal backlash corresponding the largest resp. the smallest allowances The calculation is done for the Operating pitch circle.. - Details of calculation method: cg according to method B KV according to method B KHb, KFb according method C KHa, KFa according to method B End report lines: 516

0.6

1.224 0.001366

LCa =

0.865*mn

dCa =

31.784mm

LCa =

0.865*mn

dCa =

103.781mm

7/7