Dac7611 Ic Datasheet
Dac7611 Ic Datasheet
Dac7611 Ic Datasheet
761
DAC7611
DAC
761
DESCRIPTION
The DAC7611 is a 12-bit digital-to-analog converter (DAC) with guaranteed 12-bit monotonicity performance over the industrial temperature range. It requires a single +5V supply and contains an input shift register, latch, 2.435V reference, DAC, and high speed rail-to-rail output amplifier. For a full-scale step, the output will settle to 1 LSB within 7s. The device consumes 2.5mW (0.5mA at 5V). The synchronous serial interface is compatible with a wide variety of DSPs and microcontrollers. Clock (CLK), serial data in (SDI), and load strobe (LD) comprise the serial interface. In addition, two control pins provide a chip select (CS) function and an asynchronous clear (CLR) input. The CLR input can be used to ensure that the DAC7611 output is 0V on power-up or as required by the application. The DAC7611 is available in an 8-lead SOIC or 8-pin plastic DIP package and is fully specified over the industrial temperature range of 40C to +85C.
APPLICATIONS
q PROCESS CONTROL q DATA ACQUISITION SYSTEMS q CLOSED-LOOP SERVO-CONTROL q PC PERIPHERALS q PORTABLE INSTRUMENTATION
VDD
DAC7611
Ref
CLR LD
DAC Register
CS CLK SDI
GND
International Airport Industrial Park Mailing Address: PO Box 11400, Tucson, AZ 85734 Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 Tel: (520) 746-1111 Twx: 910-952-1111 Internet: http://www.burr-brown.com/ FAXLine: (800) 548-6133 (US/Canada Only) Cable: BBRCORP Telex: 066-6491 FAX: (520) 889-1510 Immediate Product Info: (800) 548-6132
PDS-1402A
SBAS075
SPECIFICATIONS
ELECTRICAL
At TA = 40C to +85C, and VDD = +5V, unless otherwise noted. DAC7611P, U PARAMETER ACCURACY Resolution Relative Accuracy(1) Differential Nonlinearity Zero-Scale Error Full Scale Voltage ANALOG OUTPUT Output Current Load Regulation Capacitive Load Short Circuit Current Short Circuit Duration DIGITAL INPUT Data Format Data Coding Logic Family Logic Levels VIH VIL IIH IIL DYNAMIC PERFORMANCE Settling Time(2) (tS) DAC Glitch Digital Feedthrough POWER SUPPLY VDD IDD Power Dissipation Power Supply Sensitivity TEMPERATURE RANGE Specified Performance T Same specification as for DAC7611P, U. NOTES: (1) This term is sometimes referred to as Linearity Error or Integral Nonlinearity (INL). (2) Specification does not apply to negative-going transitions where the final output voltage will be within 3 LSBs of ground. In this region, settling time may be double the value indicated. To 1 LSB of Final Value CONDITIONS MIN 12 2 1 1 4.079 5 TYP MAX MIN T 1 1 T 4.087 T 3 DAC7611PB, UB TYP MAX UNITS Bits LSB LSB LSB V mA LSB pF mA
Guaranteed Monotonic Code 000H Code FFFH Code 800H RLOAD 402, Code 800H No Oscillation GND or VDD
+2 +1 +3 4.111
+1 +1 T 4.103
2.4 0.8 10 10 7 15 2 +4.75 VIH = 5V, VIL = 0V, No Load, at Code 000H VIH = 5V, VIL = 0V, No Load VDD = 5% 40 +5.0 0.5 2.5 0.001 +5.25 1 5 0.004 +85
T T T T T T T T T T T T T T T T T
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the users own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems.
DAC7611
PIN CONFIGURATION
Top View DIP
PIN DESCRIPTION
PIN 1 LABEL VDD CS CLK SDI LD DESCRIPTION Power Supply Chip Select (active LOW). Synchronous Clock for the Serial Data Input. Serial Data Input. Data is clocked into the internal serial register on the rising edge of CLK. Loads the Internal DAC Register. NOTE: The DAC register is a transparent latch and is transparent when LD is LOW (regardless of the state of CS or CLK). Asynchronous Input to Clear the DAC Register. When CLR is strobbed LOW, the DAC register is set to 000H and the output voltage to 0V. Ground Voltage Output. Fixed output voltage range of approximately 0V to 4.095V (1mV/LSB). The internal reference maintains this output range over time, temperature, and power supply variations (within the values defined in the specifications section).
1 2 3 4 DAC7611
8 7 6 5
2 3 4 5
CLR
PIN CONFIGURATION
Top View SOIC 7 8 GND VOUT
1 2 3 4 DAC7611
8 7 6 5
This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION
MINIMUM RELATIVE ACCURACY (LSB) 2 2 1 1 DIFFERENTIAL NONLINEARITY (LSB) 1 1 1 1 SPECIFICATION TEMPERATURE RANGE 40C to +85C 40C to +85C 40C to +85C 40C to +85C PACKAGE DRAWING NUMBER(1) 006 182
TRANSPORT MEDIA Rails Rails Tape and Reel Rails Rails Tape and Reel
"
DAC7611PB DAC7611UB
" "
" "
" "
"
8-Pin DIP 8-Lead SOIC
"
006 182
"
"
"
NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of DAC7611/2K5 will get a single 2500-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book.
DAC7611
DAC Switches
12 CLR
Force to 000H
DAC Register
LD Latched Transparent 12
SDI
Data
CS
CLK
DAC7611
TIMING DIAGRAMS
(MSB) SDI D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 (LSB) D0
tDH
tCH
TIMING SPECIFICATIONS
TA = 40C to +85C and V DD = +5V. SYMBOL tCH tCL tLDW tDS tDH tCLRW tLD1 tLD2 tCSS tCSH DESCRIPTION Clock Width HIGH Clock Width LOW Load Pulse Width Data Setup Data Hold Clear Pulse Width Load Setup Load Hold Select Deselect MIN TYP MAX UNITS 30 30 20 15 15 30 15 10 30 20 ns ns ns ns ns ns ns ns ns ns
Positive Logic Transition; Negative Logic Transition; X = Dont Care. NOTES: (1) CS and CLK are interchangeable. (2) A HIGH value is suggested in order to avoid to false clock from advancing the shift register and changing the DAC voltage. (3) If data is clocked into the serial register while LD is LOW, the DAC output voltage will change, reflecting the current value of the serial shift register.
NOTE: All input control signals are specified with tR = tF = 5ns (10% to 90% of +5V) and timed from a voltage level of 1.6V. These parameters are guaranteed by design and are not subject to production testing.
DAC7611
4
Output Voltage (V)
100
Delta VOUT (mV)
10
0.1
0.01 0.001
0.01
0.1
10
100
Current (mA)
BROADBAND NOISE
3.2
Supply Current (mA)
2.4
1.6
0.8
0
Time (2ms/div)
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
4.8
40 30 20 10 0 Frequency (Hz)
4.6
4.4
4.2
4.0 0.010
0.100
1.000
10.000
DAC7611
40
3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 3.0 3.5 4.0 4.5 5.0 50
VDD = 5.0V
VDD = 5.25V
Temperature (C)
VOUT (10mV/div)
VOUT
VOUT (10mV/div)
VOUT
7FFH to 800H
800H to 7FFH
Time (500ns/div)
Time (500ns/div)
1V/div
VOUT
VOUT LD
Time (20s/div)
Time (10s/div)
DAC7611
Noise (V/Hz)
1.000
VOUT
LD
0.100
0.010
Time (10s/div)
10
100
1k Frequency (Hz)
10k
100k
TOTAL UNADJUSTED ERROR HISTOGRAM T.U.E = INL = ZS + FS Sample Size = 300 Units TA = +25C
Number of Units
1200
2 1 0 1 2 3 4 5 0 200 400 600 800 1000 Hours of Operation at +150C min avg max
40 30 20 10 0 12
12
Avg + 3
4.105 4.100 4.095 4.090 4.085 4.080 4.075 50 25 0 25 50 75 100 125 Temperature (C) Avg 3 Avg
Zero-Scale (mV)
DAC7611
LINEARITY ERROR vs DIGITAL CODE (at +85C) 2.0 1.5 2.0 1.5
1.0 0.5 0 0.5 1.0 1.5 2.0 0 512 1024 1536 2048 Code 2560 3072 3584 4096
1.0 0.5 0 0.5 1.0 1.5 2.0 0 512 1024 1536 2048 Code 2560 3072 3584 4096
1.0 0.5 0 0.5 1.0 1.5 2.0 0 512 1024 1536 2048 Code 2560 3072 3584 4096
DAC7611
OPERATION
The DAC7611 is a 12-bit digital-to-analog converter (DAC) complete with a serial-to-parallel shift register, DAC register, laser-trimmed 12-bit DAC, on-board reference, and a rail-to-rail output amplifier. Figure 1 shows the basic operation of the DAC7611. INTERFACE Figure 1 shows the basic connection between a microcontroller and the DAC7611. The interface consists of a serial clock (CLK), serial data (SDI), and a load strobe signal (LD). In addition, a chip select (CS) input is available to enable serial communication when there are multiple serial devices. The data format is Straight Binary and is loaded MSB-first into the shift registers. An asynchronous
DAC7611 Full-Scale Range = 4.095V Least Significant Bit = 1mV DIGITAL INPUT CODE STRAIGHT BINARY FFFH 801H 800H 7FFH 000H ANALOG OUTPUT (V) +4.095 +2.049 +2.048 +2.047 0
DESCRIPTION Full Scale Midscale + 1 LSB Midscale Midscale 1 LSB Zero Scale
clear input (CLR) is provided to simplify start-up or periodic resets. Table I shows the relationship between input code and output voltage. The digital data into the DAC7611 is double-buffered. This means that new data can be entered into the DAC without disturbing the old data and the analog output of the converter. At some point after the data has been entered into the serial shift register, this data can be transferred into the DAC register. This transfer is accomplished with a HIGH to LOW transition of the LD pin. However, the LD pin makes the DAC register transparent. If new data is shifted into the shift register while LD is LOW, the DAC output voltage will change as each new bit is entered. To prevent this, LD must be returned HIGH prior to shifting in new serial data. At any time, the contents of the DAC register can be set to 000H (analog output equals 0V) by taking the CLR input LOW. The DAC register will remain at this value until CLR is returned HIGH and LD is taken LOW to allow the contents of the shift register to be transferred to the DAC register. If LD is LOW when CLR is taken LOW, the DAC register will be set to 000H and the analog output driven to 0V. When CLR is returned HIGH, the DAC register will be set to the current value in the serial shift register and the analog output will respond accordingly. DIGITAL-TO-ANALOG CONVERTER The internal DAC section is a 12-bit voltage output device that swings between ground and the internal reference voltage. The DAC is realized by a laser-trimmed R-2R ladder network which is switched by N-channel MOSFETs. The DAC output is internally connected to the rail-to-rail output operational amplifier. OUTPUT AMPLIFIER A precision, low-power amplifier buffers the output of the DAC section and provides additional gain to achieve a 0 to 4.095V range. The amplifier has low offset voltage, low noise, and a set gain of 1.682V/V (4.095/2.435). See Figure 2 for an equivalent circuit schematic of the analog portion of the DAC7611.
R-2R DAC 2R Output Amplifier
DAC7611 + 1 0.1F 2 Serial Clock From C Serial Data Load Strobe 3 4 VDD CS CLK SDI VOUT GND CLR LD 8 7 6 5 0V to +4.095V
10F
2R
2R
DAC7611
10
The output amplifier has a 7s typical settling time to 1 LSB of the final value. Note that there are differences in the settling time for negative-going signals versus positivegoing signals. The rail-to-rail output stage of the amplifier provides the full-scale range of 0V to 4.095V while operating on a supply voltage as low as 4.75V. In addition to its ability to drive resistive loads, the amplifier will remain stable while driving capacitive loads of up to 500pF. See Figure 3 for an equivalent circuit schematic of the amplifiers output driver and the Typical Performance Curves section for more information regarding settling time, load driving capability, and output noise.
The DAC7611 power supply should be bypassed as shown in Figure 1. The bypass capacitors should be placed as close to the device as possible, with the 0.1uF capacitor taking priority in this regard. The Power Supply Rejection vs Frequency graph in the Typical Performance Curves section shows the PSRR performance of the DAC7611. This should be taken into account when using switching power supplies or DC/DC converters. In addition to offering guaranteed performance with VDD in the 4.75V to 5.25V range, the DAC7611 will operate with reduced performance down to 4.5V. Operation between 4.5V and 4.75V will result in longer settling time, reduced performance, and current sourcing capability. Consult the VDD vs Load Current graph in the Typical Performance Curves section for more information.
VDD P-Channel
APPLICATIONS
POWER AND GROUNDING The DAC7611 can be used in a wide variety of situations from low power, battery operated systems to large-scale industrial process control systems. In addition, some applications require better performance than others, or are particularly sensitive to one or two specific parameters. This diversity makes it difficult to define definite rules to follow concerning the power supply, bypassing, and grounding. The following discussion must be considered in relation to the desired performance and needs of the particular system. A precision analog component requires careful layout, adequate bypassing, and a clean, well-regulated power supply. As the DAC7611 is a single-supply, +5V component, it will often be used in conjunction with digital logic, microcontrollers, microprocessors, and digital signal processors. The more digital logic present in the design and the higher the switching speed, the more difficult it will be to achieve good performance. Because the DAC7611 has a single ground pin, all return currents, including digital and analog return currents, must flow through this pin. The GND pin is also the ground reference point for the internal bandgap reference. Ideally, GND would be connected directly to an analog ground plane. This plane would be separate from the ground connection for the digital components until they are connected at the power entry point of the system (see Figure 4). The power applied to VDD should be well regulated and lownoise. Switching power supplies and DC/DC converters will often have high-frequency glitches or spikes riding on the output voltage. In addition, digital components can create similar high frequency spikes as their internal logic switches states. This noise can easily couple into the DAC output voltage through various paths between VDD and VOUT.
VOUT
N-Channel
AGND
POWER SUPPLY A BiCMOS process and careful design of the bipolar and CMOS sections of the DAC7611 result in a very low power device. Bipolar transistors are used where tight matching and low noise are needed to achieve analog accuracy, and CMOS transistors are used for logic, switching functions and for other low power stages. If power consumption is critical, it is important to keep the logic levels on the digital inputs (SDI, CLK, CS, LD, CLR) as close as possible to either VDD or ground. This will keep the CMOS inputs (see Supply Current vs Logic Input Voltages in the Typical Performance Curves) from shunting current between VDD and ground. Thus, CMOS logic levels rather than TTL logic levels, are strongly recommended for driving the DAC7611.
11
DAC7611
As with the GND connection, VDD should be connected to a +5V power supply plane or trace that is separate from the connection for digital logic until they are connected at the power entry point. In addition, the 10F and 0.1F capacitors shown in Figure 4 are strongly recommended and should be installed as close to VDD and ground as possible. In some situations, additional bypassing may be required such as a 100F electrolytic capacitor or even a Pi filter made up of inductors and capacitorsall designed to essentially lowpass filter the +5V supply, removing the high frequency noise (see Figure 4).
OFFSET ERROR MEASUREMENT As with most DACs, the DAC7611 can have an offset error (or zero scale error) which is either negative or positive. If the error is positive, the output voltage for an input code of 000H will be greater than 0V. If the error is negative, the output voltage is below 0V. However, since the DAC7611 is a single-supply device and cannot swing below ground, the output voltage will be 0V, giving the impression that the offset error is zero. Since measuring the offset error on a DAC is such a common task, a method is needed to reliably measure the offset error of the DAC7611. This can easily be done as shown in Figure 5. The resistor between VOUT and a negative voltage provides the output amplifier some ability to swing below ground.
FIGURE 4. Suggested Power and Ground Connections for a DAC7611 Sharing a +5V Supply with a Digital System.
10F
i 200A
DAC7611
12
IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TIs standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customers applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TIs publication of information regarding any third partys products or services does not constitute TIs approval, warranty or endorsement thereof.
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.