Scribd
Upload
48 views4 pages

BEEE1

Power factor is the cosine of the angle difference between voltage and current. What are the advantages of electromechanical measuring instruments? 1. Operating current is small 2. Sensitivity is high 3. Consumes less power 4. Can cover wide range 5. Give the current division formula. 2. What are the applications of DC shunt motors? (i) Blowers and fan (ii) Drilling machines (iii) Lathes (iv)

Uploaded by

Sabareshwar Sankaranarayanan
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
48 views4 pages

BEEE1

Power factor is the cosine of the angle difference between voltage and current. What are the advantages of electromechanical measuring instruments? 1. Operating current is small 2. Sensitivity is high 3. Consumes less power 4. Can cover wide range 5. Give the current division formula. 2. What are the applications of DC shunt motors? (i) Blowers and fan (ii) Drilling machines (iii) Lathes (iv)

Uploaded by

Sabareshwar Sankaranarayanan
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

UNIT-I 1. Define Power factor? The ratio of average power to apparent power is called the power factor.

The power factor is the cosine of the angle difference between voltage and current Power factor= average power/apparent power=R/Z 2. What are the advantages of electromechanical measuring instruments? 1. Operating current is small 2. Sensitivity is high 3. Consumes less power 4. Can cover wide range 3. Define current? I=dq/dt. Flow of free electrons in a conductor is electric current 4. Define Capacitor? It is the property of a substance which stores energy in the form of electric field. The capacitance of element is denoted by the symbol C. it is measured in farads. 5. Give the current division formula.

UNIT-II 1. What is Back EMF? When the armature of a DC motor rotates under the influence of the driving torque, the armature conductor cuts the magnetic field and hence EMF is induced in them as like the generator. The induced emf acts in a direction opposite to the applied voltage the induced voltage is called back EMF. 2. What are types of transformers based on construction? (I) core type (ii) Shell type (iii) Berry type

3. What are the applications of DC shunt motors? (i) Blowers and fan (ii) Drilling machines (iii) Milling machines (iv) Lathes 4. What are the methods of speed control? (i) Flux control method (ii)Armature controlled method (iii)Applied voltage controlled method 5. Give the Emf equation of transformer? E1=4.44 fmN1 E2=4.44f mN2 UNIT-III 1. What is intrinsic semiconductor? A semiconductor which is in its extremely pure form is known as intrinsic semiconductor. 2. How are the extrinsic semiconductor classified? 1. N type semiconductor 2. P-type semiconductor 3. What is early effect in transistors? When the collector base region is reverse biased and reverse biased voltage is increased the depletion region is also increased. Since the base is lightly doped depletion region penetrates deeper into base region. This variation or modulation of the effective base width by the collector voltage is known as base width modulation or early effect. 4. Give the ebers Moll model

5. Classify rectifiers? 1. Half wave rectifiers 2. Full wave rectifiers 3. Bridge rectifiers UNIT-IV 1. What are the types of number system used? 1. Decimal 2.Binary 3.Hexadecimal 4.Octal 2. Convert 101012 to decimal 1*24+0*23+1*22+0*21+1*20=21 3. Draw the logic symbol of And gate and its truth table

4. State demorgan therom?

5. Classify D/A converter? 1. R-2R ladder 2.Binary R-2R ladder 3.Binary weighted resistor converter 4.Inverted R-2R ladder UNIT-V 1. What are the types of signal? 1. Analog signal 2.Digital signal 2. Give few examples of analog signal? 1. Telephone signal 2.TV signal 3.Radio broadcast signal 3. What are the processes involved in analog to digital conversion? 1. Sampling 2.Quantization 3.Encoding

4. Classify angle modulation? 1. Frequency modulation 2.Plane modulation 5. What is Facsimile? In facsimile process the effective transmission and exact reproduction of still photographs, documents and other maps have to be done

You might also like