Catalogo Eslingas y Cables TENSO

General Catalogue
Web Slings Round Slings & lashings
Height Safety Products
Lifting Clamps & Equipment
Chains & Fittings
Protection materials
Contents Catalogue
Web Slings Round Slings & lashings
Page 3
Protection Materials
Page 57
Height Safety Products
Page 72
Lifting Clamps & Equipment
Page 86
Chains & Fittings
Page 122
Contents
WLL table
Unitex introduction
Web slings Roundslings Information
MC web slings
MCEE / MCED endless web slings
MCDD / MCDDS web slings with triangles
MCDD/ MCDDS Triangle specifications
TE/ DT Round slings
TLX Premium round slings
UL Information
ULLD Round slings
ULCS coil slings
TLX Information
TLX round slings
TDQ Information
TDQ 4-layer web slings
TDQDD 4-layer web slings
TDQDD Triangle specifications
TDQDDS 4-layer web slings
TDQDDS Triangle specifications
Lashing information
25mm lashing systems
50mm lashing 2000/4000 daN systems
50mm lashing 2500/5000 daN systems
75/100 mm lashing systems
Lashing hooks
Ratchets
One Way Lashing
Unitex Anti slide matting
TURTLE MAX Timber Lashing System
AirMaxx Dunnagebags
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
4-5
6
7-8
9
10
11
12
13
14
16
17 - 18
19
20
21 - 22
23
24
25
26
27
28
29 - 34
35 - 36
37 - 38
39 - 40
41 - 42
43 - 44
45
46
47
48 - 49
50 - 51
52 - 54
55 - 56
WLL table
WorKinG load liMiT (Wll) polyesTer
Wll capacity table for webbing and roundsling

Colourcodeaccording to EN
1492-1/2
Factor
Working Load Limits with 1 webbing sling or roundsling
straight lift
choked lift
0,8
Working Load Limits with 2 webbing slings

or roundslings
00 - 70
70 - 450
450 - 600
70 - 450
450 - 600
70 - 450
450 - 600
70 - 450
450 - 600
1,4
0,7
0,5
1,4
1,12
0,8
WLL in t
WLL 1 t
1,00
0,80
2,00
1,40
1,00
0,70
0,50
1,40
1,00
1,12
0,80
WLL 2 t
2,00
1,60
4,00
2,80
2,00
1,40
1,00
2,80
2,00
2,24
1,60
WLL 3 t
3,00
2,40
6,00
4,20
3,00
2,10
1,50
4,20
3,00
3,36
2,40
WLL 4 t
4,00
3,20
8,00
5,60
4,00
2,80
2,00
5,60
4,00
4,48
3,20
WLL 5 t
5,00
4,00
10,00
7,00
5,00
3,50
2,50
7,00
5,00
5,60
4,00
WLL 6 t
6,00
4,80
12,00
8,40
6,00
4,20
3,00
8,40
6,00
6,72
4,80
WLL 8 t
8,00
6,40
16,00
11,20
8,00
5,60
4,00
11,20
8,00
8,96
6,40
WLL 10 t
10,00
8,00
20,00
14,00
10,00
7,00
5,00
14,00
10,00
11,20
8,00
WLL 12 t
12,00
9,60
24,00
16,80
12,00
8,40
6,00
16,80
12,00
13,44
9,60
WLL 15 t
15,00
12,00
30,00
21,00
15,00
10,50
7,50
21,00
15,00
16,80
12,00
WLL 20 t
20,00
16,00
40,00
28,00
20,00
14,00
10,00
28,00
20,00
22,40
16,00
WLL 25 t
25,00
20,00
50,00
35,00
25,00
17,50
12,50
35,00
25,00
28,00
20,00
WLL 30 t
30,00
24,00
60,00
42,00
30,00
21,00
15,00
42,00
30,00
33,60
24,00
WLL 40 t
40,00
32,00
80,00
56,00
40,00
28,00
20,00
56,00
40,00
44,80
32,00
WLL 50 t
50,00
40,00
100,00
70,00
50,00
35,00
25,00
70,00
50,00
56,00
40,00
WLL 60 t
60,00
48,00
120,00
84,00
60,00
42,00
30,00
84,00
60,00
67,20
48,00
WLL 70 t
70,00
56,00
140,00
98,00
70,00
49,00
35,00
98,00
70,00
78,40
56,00
WLL 80 t
80,00
64,00
160,00
112,00
80,00
56,00
40,00
112,00
80,00
89,60
64,00
WLL 90 t
90,00
72,00
180,00
126,00
90,00
63,00
45,00
126,00
90,00
100,80
72,00
WLL 100 t
100,00
80,00
200,00
140,00
100,00
70,00
50,00
140,00
100,00
112,00
80,00
WLL 110 t
110,00
88,00
220,00
154,00
110,00
77,00
55,00
154,00
110,00
123,20
88,00
WLL 115 t
115,00
92,00
230,00
161,00
115,00
80,50
57,50
161,00
115,00
128,80
92,00
WLL table
WorKinG load liMiT (Wll) ULTRALIFT
Wll capacity table for ULTRALIFT roundslings

Working Load Limits with 1 webbing sling or roundsling
straight lift
Factor
choked lift
0,8
Working Load Limits with 2 webbing slings

or roundslings
00 - 70
70 - 450
450 - 600
70 - 450
450 - 600
70 - 450
450 - 600
70 - 450
450 - 600
1,4
0,7
0,5
1,4
1,12
0,8
20,00
14,00
10,00
7,00
5,00
14,00
10,00
11,20
8,00
WLL in t
WLL 10 t
10,00
8,00
WLL 12 t
12,00
9,60
24,00
16,80
12,00
8,40
6,00
16,80
12,00
13,44
9,60
WLL 15 t
15,00
12,00
30,00
21,00
15,00
10,50
7,50
21,00
15,00
16,80
12,00
WLL 20 t
20,00
16,00
40,00
28,00
20,00
14,00
10,00
28,00
20,00
22,40
16,00
WLL 25 t
25,00
20,00
50,00
35,00
25,00
17,50
12,50
35,00
25,00
28,00
20,00
WLL 30 t
30,00
24,00
60,00
42,00
30,00
21,00
15,00
42,00
30,00
33,60
24,00
WLL 40 t
40,00
32,00
80,00
56,00
40,00
28,00
20,00
56,00
40,00
44,80
32,00
WLL 50 t
50,00
40,00
100,00
70,00
50,00
35,00
25,00
70,00
50,00
56,00
40,00
WLL 60 t
60,00
48,00
120,00
84,00
60,00
42,00
30,00
84,00
60,00
67,20
48,00
WLL 70 t
70,00
56,00
140,00
98,00
70,00
49,00
35,00
98,00
70,00
78,40
56,00
WLL 80 t
80,00
64,00
160,00
112,00
80,00
56,00
40,00
112,00
80,00
89,60
64,00
WLL 90 t
90,00
72,00
180,00
126,00
90,00
63,00
45,00
126,00
90,00
100,80
72,00
WLL 100 t
100,00
80,00
200,00
140,00
100,00
70,00
50,00
140,00
100,00
112,00
80,00
WLL100 t
100,00
80,00
200,00
140,00
100,00
70,00
50,00
140,00
100,00
112,00
80,00
WLL120 t
120,00
96,00
240,00
168,00
120,00
84,00
60,00
168,00
120,00
134,40
96,00
WLL140 t
140,00
112,00
280,00
196,00
140,00
98,00
70,00
196,00
140,00
156,80
112,00
WLL160 t
160,00
128,00
320,00
224,00
160,00
112,00
80,00
224,00
160,00
179,20
128,00
WLL180 t
180,00
144,00
360,00
252,00
180,00
126,00
90,00
252,00
180,00
201,60
144,00
WLL200 t
200,00
160,00
400,00
280,00
200,00
140,00
100,00
280,00
200,00
224,00
160,00
Unitex introduction
Unitex
The Unitex group of companies are manufacturers of textile web- and round slings and lashings
with a history of 100 years in the textile industry.
The 100 years of experience and know how is our major asset for innovation, engineering and development of new
products. Therefore we are able to manage innovative projects in close co-operation with both costumers, suppliers
and third parties. With a resource of qualified personnel we are able to build project teams around any market
demand. Furthermore we are one of the few manufacturers to produce slings right through from the basic yarn to the
finished products. Because of this, the technical ability and development expertise Unitex constantly is in search for
and implementing improvements.
With testing facilities and quality procedures we assure that all processes and products are controlled to comply with
applicable standards and specifications. Our specialized equipment subject samples to every conceivable test. Extension,
surface abrasion, chemical exposure. Tenacity, temperature and load performance profiles are just some of the test
undertaken. The standard and properties claimed for every product are established and approved by our highly qualified
laboratory staff.
DYEING
Finishing
n
ti o
PREPARATION
Yarn inspection
Warping
Twisting
I ns pe
c
WEAVING
Research &
Development
Engineering
ntrol
o
C
Quality
R&D TESTING
FABRICATION
Cutting
Sewing
Packaging
Web slings Round slings

Information
4) Way of use and handling
The European Norm has given each capacity in the EN 1492/1-2 a specific colour. This to identify the capacity of webslings and
roundslings easily and clearly
WLL 1,0 t
WLL 2,0 t
WLL 3,0 t
WLL 4,0 t
WLL 5,0 t
WLL 6,0 t
WLL 8,0 t
WLL 10,0 t and >10 t
NEW
only available via
Unitex
To make sure the stitching of the eye of a websling wont break open, the angle of opened eye
of the websling shouldnt be more than 20 degrees when it is put into a cranehook
The following rule has to be followed:
You are on the safe side as the eye of the websling at least 3,5 x as long is as the thickness
of the cranehook
max. 20
L2 > = b x 3,5
d
Be careful: sharp edges will not only damage lifting equipment, but can also lead to accidents
For this reason:
The corner radius ,r must always to be bigger than the strength ,d of the lifting equipment
If loads with sharp edges have to be lifted corner protection definitely has to be used. For
example Purtecta or Ultra Protect corner protection solutions from Unitex.
Warning:
Due to slipping of the load, both corner protection
systems, Purtecta and Ultra Protect, can be
damaged
+100C
0C
Lifting equipment made of polyester fibres with their marked capacity can be used in temperatures
between -40 degrees and +100 degrees C.
If they are being used in connection with chemicals it is absolutely necessary to contact the
manufacturer beforehand for permission.
-40C
Web slings Roundslings

Information
1) EN-Standards and Machinery Directives
For all European manufacturers are the technical demands and the references how to produce
textile lifting equipment like roundslings and webslings summarized in the EN 1492-1 (Webslings)
end the EN 1492-2 (Roundslings). Additionally the textile lifting equipment is encoded with the
CE mark according the Machinery Directory 2006/42/EG
2) Testing and Maintenance
To guarantee a safe way of using the textile lifting equipment they must be tested at least one
time per year or according the latest publications of the standard or local guidlines.
The operator of the equipment has to arrange independently of predetermining operation conditions
several test intervals. These tests may only be done by competent persons. Possible damaged
Roundslings/Webslings may only be repaired by the manufacturer or by people who have become
the power of attorney to repair from the manufacturer.
To guarantee the quality of our products the standard Webslings and Roundslings are being certified
by the AIB Vinchotte (VGS), Berufsgenossenschaft (GS) or Lloyds.
3) Lifting of loads (WLL Capacity table and lifting angle)

If a load with a certain weight has to be lifted, the person who has to coordinate this job has to make sure the correct lifting
materials are chosen. Also the number of slings, the capacity and the length has to be defined. It is also to plan the lifting
procedure and to make sure that the angle of inclination is not more than 60 degrees (an angle of more than 60 degrees is
forbidden!)
The bigger the angle of inclination, the smaller the practical capacity of the lifting equipment.
As a simple rule you can say:
By an angle of inclination up to 45 degrees the chosen lifting equipment can be calculated with only
70% of the original capacity. For example:
70% of 2T = 0,7 x 2T = 1,4T
By an angle of inclination up to 60 degrees the chosen lifting equipment can be calculated with only
50% of the original capacity. For example:
50% of 2T = 0,5 x 2T = 1,0T
0
bis 45
bis 60
ber 60
verboten!
MC web slings
MC web slings 2-layer
Type
WLL
Webbing
width
in mm
Thick- Eye length

1m
ness
in mm effective
length in
mm (L2)
Eye length
2m
effective
length in
mm (L2)
MC30
MC60
MC90
MC120
MC150
MC180
MC240
MC300
MC300
WLL 1 t
WLL 2 t
WLL 3 t
WLL 4 t
WLL 5 t
WLL 6 t
WLL 8 t
WLL 10 t
WLL 12 t
30
60
90
120
150
180
240
300
300
7
6
7,5
8
7
7
8
7
8
400
400
400
450
550
600
250
250
250
Eye length Standard

3m
eye type
effective
length in
mm (L2)
750
1000
1000
type 1
type 3
type 3
type 4
type 4
type 4
type 4
type 4
type 4
Weight 1
meter in
kg (L1)
Weight
2 meter
in kg
(L1)
Weight
3 meter
in kg
(L1)
Weight
each
meter
extra
0,25
0,44
0,71
0,45
0,79
1,25
1,67
2,12
2,95
0,65
1,14
1,80
2,40
3,06
4,14
5,25
6,85
8,35
0,20
0,35
0,55
0,73
0,94
1,20
1,50
1,97
2,36
flat eye
Type 1
Reversed eye
Type 2
Folded eye width from one side

Type 3
Folded eye width from two sides

Type 4
Folded eye 1/3 width

Type 5
TYPE
APPROVED
MCEE / MCED endless web slings

MCEE endless web slings single layer
Type
WLL
Webbing width
in mm
Thickness in
mm
Weight 0,5
meter in kg
(L1)
Weight 1 meter in kg (L1)
Weight 0,5
meter extra
in KG
MCEE30
WLL 1 t
30
3,5
0,12
0,21
0,09
MCEE60
WLL 2 t
60
0,21
0,38
0,17
MCEE90
WLL 3 t
90
0,34
0,60
0,26
MCEE120
WLL 4 t
120
0,82
0,35
MCEE150
WLL 5 t
150
3,5
1,06
0,45
MCEE180
WLL 6 t
180
3,5
1,45
0,58
MCEE240
WLL 8 t
240
1,84
0,72
MCEE300
WLL 10 t
300
3,5
2,47
0,95
MCEE300
WLL 12 t
300
3,14
1,14
TYPE
APPROVED
MCED ENDLESS WEB SLINGS 2-LAYER

Type
WLL
Webbing width
in mm
Thickness in
mm
Weight 0,5
meter in kg
(L1)
Weight 0,5
meter extra
in KG
MCED30
WLL 2 t
30
0,22
0,41
0,19
MCED60
WLL 4 t
60
0,39
0,73
0,34
MCED90
WLL 6 t
90
7,5
0,62
1,16
0,54
MCED120
WLL 8 t
120
1,57
0,72
MCED150
WLL 10 t
150
2,02
0,93
MCED180
WLL 12 t
180
2,69
1,19
MCED240
WLL 16 t
240
3,37
1,48
MCED300
WLL 20 t
300
4,5
1,96
MCED300
WLL 24 t
300
5,58
2,35
TYPE
APPROVED
10
MCDD / MCDDS
web slings with triangles
MCDD 2-layer web slings with triangles (Male/Male)
Type
WLL
Webbing
width in
mm
Thickness
in
mm
Weight 1
meter in kg
(L1)
Weight 2
meter in kg
(L1)
Weight 3
meter in kg
(L1)
Weight 1 meter
extra in KG
MCDD30
WLL 1 t
30
0,62
0,82
1,02
0,20
MCDD60
WLL 2 t
60
1,39
1,74
2,09
0,35
MCDD90
WLL 3 t
90
7,5
2,78
3,33
3,88
0,55
MCDD120
WLL 4 t
120
4,68
5,41
0,73
MCDD150
WLL 5 t
150
6,19
7,13
0,94
MCDD180
WLL 6 t
180
8,51
9,71
1,20
MCDD240
WLL 8 t
240
16,24
1,50
MCDD300
WLL 10 t
300
21,68
1,97
MCDD300
WLL 12 t
300
22,97
2,36
MCDDS 2-layer web slings with triangles (Male/Female)
Type
WLL
Webbing
width in
mm
Thickness
in mm
Weight 1
meter in kg
(L1)
Weight 3
meter in kg
(L1)
Weight 1 meter
extra in KG
MCDDS30
WLL 1 t
30
0,82
1,02
1,22
0,20
MCDDS60
WLL 2 t
60
1,86
2,21
2,56
0,35
MCDDS90
WLL 3 t
90
7,5
3,63
4,21
4,76
0,55
MCDDS120
WLL 4 t
120
6,11
6,84
0,73
MCDDS150
WLL 5 t
150
8,90
9,84
0,94
MCDDS180
WLL 6 t
180
10,79
11,99
1,20
MCDDS240
WLL 8 t
240
20,45
1,50
MCDDS300
WLL 10 t
300
27,31
1,97
11
MCDD/ MCDDS
Triangle specifications
Technical information for MCDD male triangles
Type
WLL
DTR/010 WLL 1 t
Width
in mm
Q
D
H
E
Weight
in mm in mm in mm in mm per piece in kg
30
12
45
60
70
D
D
0,2
Type
WLL
Width in mm
Q in mm
D in mm
H in mm
E in mm
Weight per Piece in kg
DTR/020
WLL 2 t
60
16
30
80
100
0,5
DTR/030
WLL 3 t
90-100
20
60
120
146
1,1
DTR/040
WLL 4 t
120
23
60
130
179
1,6
DTR/050
WLL 5 t
150
26
90
180
222
2,2
DTR/060
WLL 6 t
180
28
90
180
262
DTR/080
WLL 8 t
240
32
100
200
344
5,8
DTR/100
WLL 10 t
300
35
100
250
400
7,9
D
D
H
Technical information for MCDDS female triangles
12
Typ
WLL
Width in mm
Q in mm
D in mm
H in mm
P in mm
Weight per Piece in kg
DSTR/010
WLL 1 t
30
12
50
100
25
0,4
DSTR/020
WLL 2 t
60
16
40
146
40
DSTR/030
WLL 3 t
90-100
20
70
205
55
DSTR/040
WLL 4 t
120
23
80
218
55
3,1
DSTR/050
WLL 5 t
150
26
90
300
80
DSTR/060
WLL 6 t
180
28
90
284
80
5,4
DSTR/080
WLL 8 t
240
32
120
332
90
10,2
DSTR/100
WLL 10 t
300
35
120
385
100
13,8
DS
H
P
S
TE/ DT Round slings

TE round slings with single sleeve
TYPE
APPROVED
Type
WLL
Sleeve width
in mm
Round sling
diameter
Weight of round sling o,5 m

effective length in kg
Weight per 0,5 m

extra in kg
TE 010
WLL 1 t
47
12
0,118
0,103
TE 020
WLL 2 t
48
18
0,185
0,170
TE 030
WLL 3 t
54
20
0,264
0,248
TE 040
WLL 4 t
70
22
0,356
0,334
TE 050
WLL 5 t
72
28
0,431
0,407
TE 060
WLL 6 t
74
30
0,528
0,504
TE 080
WLL 8 t
90
32
0,701
0,670
TE 100
WLL 10 t
91
35
0,843
0,814
DT round slings with double sleeve
TYPE
APPROVED
cross section of a DT roundsling sleeve
Type
WLL
Sleeve width
in mm
Round sling
diameter

Weight per 0,5 m

extra in kg
DT 010
WLL 1 t
42
12
0,143
0,121
DT 020
WLL 2 t
47
18
0,213
0,190
DT 030
WLL 3 t
58
20
0,314
0,284
DT 040
WLL 4 t
66
22
0,392
0,360
DT 050
WLL 5 t
72
28
0,478
0,441
DT 060
WLL 6 t
77
30
0,586
0,546
DT 080
WLL 8 t
82
32
0,737
0,696
DT100
WLL 10 t
94
35
0,907
0,860
13
TLX Premium round slings

TLX round slings
+++++
the high tech round sling made from polyester

according DIN EN 1492-2
TLX is a high tech -PES- round sling from the Unitex Group. Due to the special rip
and weave structure, the Techlon sleeve is significantly more resistant to abrasion than a standard polyester sleeve.
The TLX is fitted with an extremely strong reinforced label.
1.
+ Due to the special rip and weave structure, the Techlon sleeve is significantly more resistant
to abrasion than a standard polyester sleeve.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
+ Highly compact and stable sleeve. Optimal use and reduced wear.
+ WLL printed on the sleeve continuously and additional sewn in WLL stripes for easy identification.
+ Extremely strong reinforced label.
+ According to the Machinery Directive 2006/42/EG.
+ Color coding according to EN 1492-2.
+ Stripe coded, each stripe equals 1 ton of vertical lifting capacity (up to 10 ton).
+ WLL printed on the sleeve continuously (up to 10 ton)
+ Special warp. The new type of warp gives also an extra resistance against abrasion
+ TLX round slings offers a substantial longer service life compared to standard round slings.
+ The more compact sleeve results in a better fit around the crane hook.
TLX round slings are being produced up to 150 ton WLL (Lloyds approval up to WLL 115 T.)
Type
14
WLL
Sleeve width
in mm
Round sling
diameter
TYPE
APPROVED

Weight per 0,5 m

extra in kg
TLX 010
WLL 1 t
41
12
0,149
0,125
TLX 020
WLL 2 t
51
18
0,236
0,206
TLX 030
WLL 3 t
53
20
0,320
0,288
TLX 040
WLL 4 t
69
22
0,423
0,382
TLX 050
WLL 5 t
76
28
0,501
0,457
TLX 060
WLL 6 t
80
30
0,612
0,564
TLX 080
WLL 8 t
90
32
0,782
0,728
TLX 100
WLL 10 t
96
35
0,941
0,884
Heavy lift
15
UL Information
ULTRALIFT round sling
Material:
The construction of a round sling is divided into the load bearing core and the protection sleeve.
The Utrallift Round slings is always made out of high performance fibres such as Dyneema which makes the
sling very light in weight even up to 2,5 times lighter in compare to Polyester en 8 times in compare to Steel based
slings. The Ultralift LD (ULLD) has a protection sleeve made out off 100% Dyneema This material is extremly
abrasion resistant and therefore suitable for for heavy lift applications.

Properties:
Dyneema is a High Modulus PolyEthylene Fibre (HMPE ), that offers maximum strength combined
with minimum weight.
Fysical properties
Specific Gravity (g/cm3)
:
Elongation at WLL (in %)
:
Elongation in use
:
Weight reduction in %
:

Usable at temperature
:
Effects on Chemical exposure*
:

Effects on Chemical exposure*
:
0,97
0,5
Similar to wire rope slings.
Compared to wire rope slings; < 80%
Compared to polyester based slings; < 59 %
- 50 C - + 60 C
Excellent on water, moisture, very resistant against chemicals
and micro organism. Good resistance to acid and alkali.
0,0
* Always consult the producer.

Application:
The Ultralift LD Round Sling with the light duty (UPLD) Dyneema based protection sleeve is developed for heavy lift applications
were abrasion and flexibility is required.
The Ultralift LD Round Slings are exceptionally suitable for repetitive lifting jobs. Due to the maximum strength combined
with the minimum weight, cost reductions will be achieved by spending less hours spend on rigging, less workers to rig, less
back and hand injuries, a.o.
Standards:
ULTRALIFT round slings comply with the Machinery Directive 2006/42/EG
ULTRALIFT have a CE -mark, according the Machinery Directive requirements.
Each ULTRALIFT round sling is preloaded 2 times the WLL , before delivery.
A technical dossier is composed and validated by an independent authorized body (A.I.B. Vincotte and Lloyds).
16
ULLD Round slings

ULTRALIFT LD
ULTRALIFT LD Round slings are produced out of a Dyneema

yarn and fully Comply to the machinery directive 2006/42/EG
1.
2.
+ : ULLD Round slings are suitable for precision lift due to the
low elongation
+ : Low weight (2,5 times lighter than PES, and min 8 times
lighter compared to steel wire ropes)
ULTRALIFT LD RONDSLINGS (ULLD)

Weigth of a ULTRALIFT LD Round sings
Type
ULLD0020
ULLD0030
ULLD0040
ULLD0050
ULLD0060
ULLD0080
ULLD0100
WLL
2 T.
3 t.
4 T.
5 T.
6 T.
8 t.
10 t.
sleeve type 0,5 up to 2,0 Mtr
73 mm
73 mm
83 mm
83 mm
98 mm
98 mm
123 mm
Sleeve type from 2 mtr and up
63 mm
63 mm
73 mm
73 mm
73 mm
83 mm
98 mm
kg
kg
kg
kg
kg
kg
kg
length in Mtr
0,5
ULLD
0,38
0,40
0,56
ULLD
0,66
0,71
0,98
1,04
1,09
1,31
1,56
1,5
ULLD
0,95
1,01
1,41
1,48
1,56
1,88
2,24
ULLD
1,23
1,31
1,83
1,93
2,04
2,45
2,92
2,5
ULLD
1,40
1,51
1,81
1,94
2,07
2,81
3,28
ULLD
1,66
1,79
2,15
2,30
2,46
3,34
3,90
3,5
ULLD
1,93
2,07
2,49
2,67
2,85
3,87
4,52
ULLD
2,19
2,35
2,82
3,03
3,24
4,41
5,14
4,5
ULLD
2,45
2,64
3,16
3,40
3,63
4,94
5,76
ULLD
2,71
2,92
3,50
3,76
4,03
5,47
6,39
5,5
ULLD
2,97
3,20
3,84
4,13
4,42
6,00
7,01
ULLD
3,24
3,49
4,18
4,50
4,81
6,53
7,63
6,5
ULLD
3,50
3,77
4,52
4,86
5,20
7,06
8,25
ULLD
3,76
4,05
4,86
5,23
5,59
7,59
8,87
7,5
ULLD
4,02
4,33
5,20
5,59
5,98
8,12
9,49
ULLD
4,28
4,62
5,54
5,96
6,38
8,66
10,11
8,5
ULLD
4,55
4,90
5,88
6,32
6,77
9,19
10,74
ULLD
4,81
5,18
6,22
6,69
7,16
9,72
11,36
9,5
ULLD
5,07
5,47
6,56
7,06
7,55
10,25
11,98
10
ULLD
5,33
5,75
6,90
7,42
7,94
10,78
12,60
11
ULLD
5,86
6,31
7,58
8,15
8,73
11,84
13,84
12
ULLD
6,38
6,88
8,26
8,88
9,51
12,91
15,09
13
ULLD
6,90
7,44
8,94
9,62
10,29
13,97
16,33
14
ULLD
7,43
8,01
9,62
10,35
11,08
15,03
17,57
15
ULLD
7,95
8,58
10,30
11,08
11,86
16,09
18,81
16
ULLD
8,48
9,14
10,98
11,81
12,65
17,16
20,06
17
ULLD
9,00
9,71
11,65
12,54
13,43
18,22
21,30
18
ULLD
9,52
10,27
12,33
13,27
14,21
19,28
22,54
19
ULLD
10,05
10,84
13,01
14,01
15,00
20,34
23,79
20
ULLD
10,57
11,40
13,69
14,74
15,78
21,41
25,03
Dyneema
is a registered
trademark of
Royal DSM N.V.
17
ULLD Round slings

ULTRALIFT LD Round slings are produced out of a Dyneema yarn and fully
Comply to the machinery directive 2006/42/EG
1.
2.
3.
+ : ULLD Round slings are suitable for precision lift due to the low
elongation
+ : Low weight (2,5 times lighter than PES, and min 8 times lighter
compared to steel wire ropes)
+ : extremely high abrasion resistance
ULTRALIFT LD ROUND SLINGS With LIGHT DUTY SLEEVE (ULLD)

Type
W.L.L.
Dyneema
is a registered
trademark of
Royal DSM N.V.
ULLD0015 ULLD0020 ULLD0025 ULLD0030 ULLD0040 ULLD0050 ULLD0060 ULLD0070 ULLD0080 ULLD0090 ULLD0100 ULLD0120 ULLD0140 ULLD0160 ULLD0180 ULLD0200
15t
Sleeve
98 mm
width
Core
30 mm
diameter
EWL
in mtr
Weight
in kg
20t
25t
30t
40t
50t
60t
70t
80t
90t
100t
120 t
140 t
160 t
180 t
200 t
98 mm
133 mm
133 mm
133 mm
183 mm
183 mm
183 mm
213 mm
228 mm
228 mm
283 mm
283 mm
343 mm
343 mm
343 mm
34 mm
Weight
in kg
40 mm
Weight
in kg
44 mm
Weight
in kg
48 mm
Weight
in kg
71 mm
75 mm
87 mm
90 mm
94 mm
Weight
in kg
Weight
in kg
Weight
in kg
Weight
in kg
Weight
in kg
100 mm
108 mm
116 mm
125 mm
132 mm
140 mm
Weight
in kg
Weight
in kg
Weight
in kg
Weight
in kg
Weight
in kg
Weight
in kg
2,5
ULLD
4,2
4,8
6,2
6,8
8,2
13,1
14,1
17,2
18,9
20,4
ULLD
4,9
5,7
7,3
8,0
9,6
15,4
16,6
20,4
22,3
24,2
32,6
33,6
41,2
46,9
51,0
55,1
3,5
ULLD
5,7
6,5
8,4
9,3
11,0
17,7
19,2
23,5
25,8
27,9
37,0
38,7
47,0
53,7
58,5
63,3
ULLD
6,4
7,3
9,5
10,5
12,5
20,0
21,7
26,7
29,2
31,7
41,4
43,9
52,9
60,5
66,0
71,5
4,5
ULLD
7,1
8,2
10,7
11,7
13,9
22,4
24,2
29,8
32,7
35,4
45,9
49,0
58,8
67,3
73,4
79,6
ULLD
7,8
9,0
11,8
13,0
15,4
24,7
26,7
33,0
36,1
39,2
50,3
54,2
64,6
74,0
80,9
87,8
5,5
ULLD
8,6
9,9
12,9
14,2
16,8
27,0
29,3
36,1
39,6
42,9
54,8
59,4
70,5
80,8
88,4
95,9
ULLD
9,3
10,7
14,0
15,4
18,3
29,3
31,8
39,2
43,0
46,7
59,2
64,5
76,4
87,6
95,9
104,1
6,5
ULLD
10,0
11,6
15,1
16,6
19,7
31,6
34,3
42,4
46,5
50,4
63,7
69,7
82,2
94,4
103,3
112,3
ULLD
10,7
12,4
16,2
17,9
21,1
33,9
36,8
45,5
49,9
54,2
68,1
74,8
88,1
101,2
110,8
120,4
7,5
ULLD
11,4
13,2
17,3
19,1
22,6
36,3
39,4
48,7
53,4
57,9
72,6
80,0
94,0
108,0
118,3
128,6
ULLD
12,2
14,1
18,4
20,3
24,0
38,6
41,9
51,8
56,9
61,6
77,0
85,1
99,8
114,8
125,8
136,7
8,5
ULLD
12,9
14,9
19,5
21,5
25,5
40,9
44,4
55,0
60,3
65,4
81,5
90,3
105,7
121,6
133,2
144,9
ULLD
13,6
15,8
20,6
22,8
26,9
43,2
46,9
58,1
63,8
69,1
85,9
95,4
111,6
128,3
140,7
153,1
9,5
ULLD
14,3
16,6
21,7
24,0
28,3
45,5
49,5
61,3
67,2
72,9
90,3
100,6
117,5
135,1
148,2
161,2
10
ULLD
15,1
17,5
22,8
25,2
29,8
47,9
52,0
64,4
70,7
76,6
94,8
105,7
123,3
141,9
155,6
169,4
11
ULLD
16,5
19,1
25,0
27,7
32,7
52,5
57,0
70,7
77,6
84,1
103,7
116,0
135,1
155,5
170,6
185,7
12
ULLD
18,0
20,8
27,3
30,1
35,5
57,1
62,1
77,0
84,5
91,6
112,6
126,3
146,8
169,1
185,5
202,0
13
ULLD
19,4
22,5
29,5
32,6
38,4
61,8
67,1
83,3
91,4
99,1
121,5
136,6
158,5
182,6
200,5
218,3
14
ULLD
20,8
24,2
31,7
35,0
41,3
66,4
72,2
89,6
98,3
106,6
130,3
147,0
170,3
196,2
215,4
234,7
15
ULLD
22,3
25,9
33,9
37,5
44,2
71,0
77,2
95,9
105,2
114,1
139,2
157,3
182,0
209,8
230,4
251,0
16
ULLD
23,7
27,6
36,1
40,0
47,1
75,7
82,3
102,2
112,1
121,6
148,1
167,6
193,8
223,3
245,3
267,3
17
ULLD
25,2
29,3
38,3
42,4
50,0
80,3
87,3
108,5
119,0
129,1
157,0
177,9
205,5
236,9
260,3
283,6
18
ULLD
26,6
31,0
40,5
44,9
52,8
84,9
92,4
114,7
125,9
136,6
165,9
188,2
217,2
250,5
275,2
299,9
19
ULLD
28,1
32,6
42,8
47,3
55,7
89,6
97,4
121,0
132,8
144,1
174,8
198,5
229,0
264,1
290,2
316,3
20
ULLD
29,5
34,3
45,0
49,8
58,6
94,2
102,5
127,3
139,8
151,6
183,7
208,8
240,7
277,6
305,1
332,6
18
ULCS coil slings

ULTRALIFT-coilsling with an ULTRAproTecT heavy duty sleeve (ulnG)
The Coil Sling NG consists of two parts: The ULTRALlFT round sling as a perfect round
sling with a high abrasion resistant cover made of dyneema. (upld). over both legs
an ULTRAPROTECT heavy duty protection sleeve is placed. The ULTRAPROTECT (UPHD)
protection sleeve is extremely cut- and abrasion resistant.
Application:
This patented ULTRALIFT coil sling is especially developed for lifting coils and loads
which are heavy and sharp.
The benefits of this concept are:
+ : in case of severe damages the protection sleeve can be replaced easily, without
replacing the ULTRALIFT round sling.
+ : easy handling, due to the size of the ULTRALIFT round sling that fits perfectly
into the hook
+ : The total weight of the ULTRALIFT coil sling NG is extremely low.
+ : The lifetime of the ulld will be very long, because of the dyneema based cover.
+ : discharge indicator on the ULTRAPROTECT protection sleeve. (red marker yarns).
Type
ULCS0010
ULCS0015
ULCS0020
ULCS0025
ULCS0030
Sleeve width actual ULLD Roundsling
75 - 85mm
90-100 mm
90-100 mm
115-125 mm
115-125 mm
Sleeve width extra UPHD protection sleeve actual Roundsling
115-125mm
145-155mm
145-155mm
175 -185mm
175-185mm
10 t
15 t
20 t
25 t
30 t
[kg]
[kg]
[kg]
[kg]
[kg]
WLL
L in mtr
Dyneema
is a registered
trademark of
Royal DSM N.V.
Length UPHD
protection sleeve
2,5
1,9
ULCS
4,9
6,2
6,4
8,6
9,2
2,4
ULCS
5,9
7,4
7,7
10,3
11
3,5
2,9
ULCS
6,9
8,7
9,1
12
12,9
3,4
ULCS
7,9
9,9
10,5
13,7
14,7
4,5
3,9
ULCS
8,8
11,2
11,8
15,5
16,5
18,4
4,4
ULCS
9,8
12,4
13,2
17,2
5,5
4,9
ULCS
10,8
13,7
14,6
18,9
20,2
5,4
ULCS
11,8
14,9
15,9
20,6
22,1
6,5
5,9
ULCS
12,7
16,1
17,3
22,4
23,9
6,4
ULCS
13,7
17,4
18,7
24,1
25,8
7,5
6,9
ULCS
14,7
18,6
20,0
25,8
27,6
29,5
7,4
ULCS
15,7
19,9
21,4
27,5
8,5
7,9
ULCS
16,7
21,1
22,7
29,3
31,3
8,4
ULCS
17,6
22,4
24,1
31
33,1
9,5
8,9
ULCS
18,6
23,6
25,5
32,7
35
10
9,4
ULCS
19,6
24,8
26,8
34,4
36,8
19
TLX Informationen
Techlon ROUND SLING (TLX)
Material:
The construction of a sling is divided into the core and a protection sleeve.
The core is made out of polyester (PES ) fibres. The protection sleeve is made out of Techlon (PES).
Due to the special rip and weave structure, Techlon is significantly more resistance to abrasion than
standard polyester sleeve.
Physical properties
Moisture regain %
Resistance to mineral Acid*
Resistance to Alkalis*
:
:
:
:
:
:
1,38
3-4
-40C - +100C
< 0,5
Good
Poor

Application:
Techlon (TLX ) round slings are for general use for lifting loads from WLL 1 ton up to 150 ton. (straight lift).
For the standard assortment we refer to the enclosed product sheets.
Standards:
Techlon round slings comply with the Machinery Directive 2006/42/EG
Techlon round slings have a CE-mark, according the Machinery Directive requirements. (Europe).
Techlon round slings comply with NEN-EN 1492-2 (europe), BS 3481/part2-1983 safety factor 6:1
(middle east, asia), AS 4497.1-1997 (Australia), OSHA /AS ME B30.9 (USA )
20
TLX round slings

Techlon (TLX)
Weight of a TLX round sling with Techlon sleeve in kg

Type
TLX0100
TLX0150
TLX0200
TLX0250
TLX0300
TLX0350
TLX0400
TLX0450
TLX0500
TLX0550
WLL
12 t
15 t
20 t
25 t.
30 t
35 t
40 t
45 t
50 t
55 t
Sleeve width
110 mm
110 mm
132 mm
132 mm
160 mm
160 mm
160 mm
180 mm
180 mm
180 mm
Core
diameter
39 mm
46 mm
52 mm
60 mm
65 mm
67 mm
73 mm
78 mm
86 mm
90 mm
kg
kg
kg
kg
kg
kg
kg
kg
kg
kg
2,6
3,4
4,4
5,6
6,2
7,3
n/a
n/a
n/a
n/a
EWL in mtr
1
TLX
TLX
5,1
6,6
8,5
11,0
12,3
14,5
16,0
18,9
22,7
25,2
TLX
7,5
9,8
12,7
16,5
18,5
21,6
23,9
28,1
33,9
37,6
TLX
9,9
13,0
16,8
21,9
24,6
28,7
31,8
37,4
45,0
50,0
TLX
12,4
16,2
21,0
27,3
30,7
35,8
39,7
46,7
56,2
62,5
TLX
14,8
19,5
25,2
32,7
36,9
42,9
47,6
55,9
67,4
74,9
TLX
17,3
22,7
29,3
38,2
43,0
50,0
55,5
65,2
78,6
87,3
TLX
19,7
25,9
33,5
43,6
49,1
57,1
63,3
74,4
89,7
99,7
TLX
22,2
29,1
37,6
49,0
55,3
64,2
71,2
83,7
100,9
112,1
10
TLX
24,6
32,3
41,8
54,4
61,4
71,3
79,1
93,0
112,1
124,6
11
TLX
27,0
35,5
45,9
59,9
67,6
78,4
87,0
102,2
123,3
137,0
12
TLX
29,5
38,7
50,1
65,3
73,7
85,5
94,9
111,5
134,5
149,4
13
TLX
31,9
41,9
54,3
70,7
79,8
92,6
102,8
120,7
145,6
161,8
14
TLX
34,4
45,2
58,4
76,1
86,0
99,7
110,7
130,0
156,8
174,2
15
TLX
36,8
48,4
62,6
81,5
92,1
106,8
118,5
139,3
168,0
186,6
16
TLX
39,2
51,6
66,7
87,0
98,3
113,9
126,4
148,5
179,2
199,1
17
TLX
41,7
54,8
70,9
92,4
104,4
121,0
134,3
157,8
190,3
211,5
18
TLX
44,1
58,0
75,1
97,8
110,5
128,2
142,2
167,1
201,5
223,9
19
TLX
46,6
61,2
79,2
103,2
116,7
135,3
150,1
176,3
212,7
236,3
20
TLX
49,0
64,4
83,4
108,7
122,8
142,4
158,0
185,6
223,9
248,7
2,5
3,2
4,2
5,4
6,1
7,1
7,9
9,3
11,2
12,4
Extra per mtr.

working length
21
TLX round slings

Weight of a TLX round sling with Techlon sleeve in kg
Type
TLX0600
TLX0650
TLX0700
TLX0750
TLX0800
TLX0850
TLX0900
TLX0950
TLX1000
TLX 1150
WLL
60 t
65 t
70 t
75 t
80 t
85 t
90 t
95 t
100 t
115 t
Sleeve width
220 mm
220 mm
220 mm
320 mm
320 mm
320 mm
320 mm
320 mm
320 mm
320 mm
Core
diameter
95 mm
98 mm
101 mm
105 mm
108 mm
112 mm
116 mm
120 mm
123 mm
140 mm
kg
kg
kg
kg
kg
kg
kg
kg
kg
kg
TLX
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
TLX
27,4
29,6
31,3
n/a
n/a
n/a
n/a
n/a
n/a
n/a
EWL in mtr
TLX
40,9
44,2
46,8
51,6
54,1
57,9
60,4
64,2
66,7
84,6
TLX
54,4
58,8
62,2
68,6
72,0
77,0
80,4
85,4
88,7
122,6
TLX
67,9
73,4
77,7
85,6
89,8
96,1
100,3
106,6
110,8
140,7
TLX
81,4
88,1
93,1
102,7
107,7
115,3
120,3
127,9
132,8
168,7
TLX
94,9
102,7
108,6
119,7
125,5
134,4
140,2
149,1
154,9
196,7
TLX
108,4
117,3
124,0
136,7
143,4
153,5
160,2
170,3
176,9
224,8
TLX
121,9
131,9
139,5
153,7
161,2
172,6
180,1
191,5
199,0
252,8
10
TLX
135,4
146,5
154,9
170,7
179,1
191,7
200,1
212,7
221,0
280,8
11
TLX
148,9
161,1
170,4
187,7
196,9
210,8
220,0
233,9
243,0
309,0
12
TLX
162,4
175,7
185,9
204,8
214,8
230,0
240,0
255,2
265,1
337,0
13
TLX
175,9
190,3
201,3
221,8
232,7
249,1
260,0
276,4
287,1
365,0
14
TLX
189,4
204,9
216,8
238,8
250,5
268,2
279,9
297,6
309,2
393,0
15
TLX
202,9
219,5
232,2
255,8
268,4
287,3
299,9
318,8
331,2
421,0
16
TLX
216,4
234,1
247,7
272,8
286,2
306,4
319,8
340,0
353,3
449,0
17
TLX
229,9
248,7
263,1
289,9
304,1
325,6
339,8
361,3
375,3
477,0
18
TLX
243,4
263,4
278,6
306,9
321,9
344,7
359,7
382,5
397,4
505,0
19
TLX
256,9
278,0
294,0
323,9
339,8
363,8
378,9
403,7
419,4
535,0
TLX
270,4
292,6
309,5
340,9
357,6
382,9
399,6
424,9
441,4
565,0
Extra per mtr.

working length
13,5
14,6
15,5
17,0
17,9
19,1
20,0
21,2
22,0
30,0
20
22
TDQ Information
TDQ web slings
Material:
TDQ web slings are built up out of 4-layers polyester (PES ) and are available as three versions:
TDQ web slings are made out 100% polyester. The TDQDD and TDQDDS are manufactured with steel triangles (grade 80).
Properties:
Fysical properties
Moisture regain %
Resistance to mineral Acid*
Resistance to Alkalis*
:
:
:
:
:
:
1,38
3-4
-40C - +100C
< 0,5
Good
Poor

Application:
TDQ web slings are for general use for lifting loads from WLL 2 ton up to 40 ton. (straight lift). The width of the webbing
sling contributes to a stable and safe lift.
For special applications where the standard assortment does not fit, Technotex Industrial Supply can offer custom made
solutions.
For the standard assortment we refer to the enclosed product sheets.
Standards:
TDQ web slings comply with the Machinery Directive 2006/42/EG
TDQ web slings have a CE-mark, according to the Machinery Directive requirements. (Europe).
Techlon web slings comply with NEN-EN 1492-2 (europe), BS 3481/part2-1983 safety factor 6:1
(Middle East, asia), as 4497.1-1997 (Australia), OSHA/ASME B30.9 (USA)
23
TDQ 4-layer web slings

TDQ
TDQ: 4- layer web slings

Weight of a 4-layer TDQ web sling.
Type
TDQ150
TDQ240
TDQ300
TDQ300
TDQ500
TDQ600
WLL
10 t
12 t
15 t
20 t
25 t
30 t
40 t
Eye width
80 mm
95/105
125 mm
160 mm
160 mm
260 mm
310 mm
Eye length
650 mm
700 mm
850 mm
1100 mm
1200 mm
1500 mm
1500 mm
Webbing width
150 mm
180/200
240 mm
300 mm
300 mm
500 mm
600 mm
kg
kg
kg
kg
kg
kg
kg
7,7
10,1
12,4
16,3
19,6
26,5
41,0
EWL in mtr
4
TDQ
TDQ
9,6
12,5
15,4
20,3
24,3
32,9
50,8
TDQ
11,4
14,9
18,3
24,2
29,0
39,2
60,6
TDQ
13,3
17,3
21,3
28,1
33,7
45,6
70,4
TDQ
15,1
19,7
24,3
32,0
38,4
52,0
80,2
TDQ
17,0
22,1
27,2
35,9
43,1
58,4
90,1
10
TDQ
18,8
24,5
30,2
39,8
47,8
64,7
99,9
11
TDQ
20,7
26,9
33,2
43,7
52,5
71,1
109,7
12
TDQ
22,5
29,3
36,1
47,6
57,2
77,5
119,5
13
TDQ
24,4
31,7
39,1
51,5
61,9
83,8
129,3
14
TDQ
26,2
34,1
42,1
55,4
66,6
90,2
139,2
15
TDQ
28,1
36,5
45,1
59,4
71,3
96,6
149,0
16
TDQ
29,9
38,9
48,0
63,3
76,0
102,9
158,8
17
TDQ
31,8
41,3
51,0
67,2
80,7
109,3
168,6
18
TDQ
33,6
43,7
54,0
71,1
85,4
115,7
178,4
19
TDQ
35,5
46,1
56,9
75,0
90,1
122,1
188,3
20
TDQ
37,3
48,5
59,9
78,9
94,8
128,4
198,1
Extra per mtr.

working length*
1,9
2,4
3,0
3,9
4,7
6,4
9,8
* length above 24 meter please consult the manufacturer.
24
TDQ180/200
TDQDD 4-layer triangle web slings

TDQDD
TDQDD 4-layer web sling with triangles (MALE )

Weigth of a 4-layer TDQDD web sling with triangles (Male)
Type
TDQDD150
TDQDD180/200
TDQDD180/200
TDQDD240
TDQDD300
WLL
10 t
12 t
12 t
15 t
20 t
25 t
Webbing width
150 mm
180/200
180/200
240 mm
300 mm
300 mm
Weight Triangle
12,6
15,6
15
28,8
47,8
47,8
kg
kg
kg
kg
kg
kg
EWL in mtr
TDQDD300
TDQDD
20,3
25,7
10,1
41,2
64,1
67,4
TDQDD
22,2
28,1
12,5
44,2
68,1
72,1
TDQDD
24,0
30,5
14,9
47,1
72,0
76,8
TDQDD
25,9
32,9
17,3
50,1
75,9
81,5
TDQDD
27,7
35,3
19,7
53,1
79,8
86,2
TDQDD
29,6
37,7
22,1
56,0
83,7
90,9
10
TDQDD
31,4
40,1
24,5
59,0
87,6
95,6
11
TDQDD
33,3
42,5
26,9
62,0
91,5
100,3
12
TDQDD
35,1
44,9
29,3
64,9
95,4
105,0
13
TDQDD
37,0
47,3
31,7
67,9
99,3
109,7
14
TDQDD
38,8
49,7
34,1
70,9
103,2
114,4
15
TDQDD
40,7
52,1
36,5
73,9
107,2
119,1
16
TDQDD
42,5
54,5
38,9
76,8
111,1
123,8
17
TDQDD
44,4
56,9
41,3
79,8
115,0
128,5
18
TDQDD
46,2
59,3
43,7
82,8
118,9
133,2
19
TDQDD
48,1
61,7
46,1
85,7
122,8
137,9
TDQDD
49,9
64,1
48,5
88,7
126,7
142,6
Extra per mtr.

working length*
1,8
2,4
2,4
2,9
3,9
4,7
20
25

TDQDD

Triangle Type 2 - male
Type
W.L.L.
S in mm
Q in mm
D in mm
H in mm
E in mm
weigth in kg
DTR/10
10
180
35
100
200
320
6,3
DTR/12
12
170
40
90
200
290
7,8
DTR/15
15
300
45
150
250
440
14,4
DTR/20
20
300
50
180
300
460
19
DTR/25
25
300
55
180
300
492
23,9
DTR/30
30
300
55
180
300
492
23,9
D
D
H
26
TDQDDS 4-layer triangle web slings

TDQDDS
TdQdds 4-layer WeB slinG WiTh TrianGles (Male/FeMale)

Weigth of a 4-layer TDQDDS web sling with triangles (Male/Female)
Type
TDQDDS150
TDQDDS180/200
TDQDD180/200
TDQDDS240
TDQDDS300
TDQDDS300
WLL
10 t
12 t
12 t
15 t
20 t
25 t
Webbing width
150 mm
180/200
180/200
240 mm
300 mm
300 mm
Weight Triangle
19,3
23,3
30
41,6
71,4
71,4
kg
kg
kg
kg
kg
kg
TDQDDS
27,0
33,4
10,1
54,0
87,7
91,0
TDQDDS
28,9
35,8
12,5
57,0
91,7
95,7
TDQDDS
30,7
38,2
14,9
59,9
95,6
100,4
TDQDDS
32,6
40,6
17,3
62,9
99,5
105,1
TDQDDS
34,4
43,0
19,7
65,9
103,4
109,8
EWL in mtr
TDQDDS
36,3
45,4
22,1
68,8
107,3
114,5
10
TDQDDS
38,1
47,8
24,5
71,8
111,2
119,2
11
TDQDDS
40,0
50,2
26,9
74,8
115,1
123,9
12
TDQDDS
41,8
52,6
29,3
77,7
119,0
128,6
13
TDQDDS
43,7
55,0
31,7
80,7
122,9
133,3
14
TDQDDS
45,5
57,4
34,1
83,7
126,8
138,0
15
TDQDDS
47,4
59,8
36,5
86,7
130,8
142,7
16
TDQDDS
49,2
62,2
38,9
89,6
134,7
147,4
17
TDQDDS
51,1
64,6
41,3
92,6
138,6
152,1
18
TDQDDS
52,9
67,0
43,7
95,6
142,5
156,8
19
TDQDDS
54,8
69,4
46,1
98,5
146,4
161,5
20
TDQDDS
56,6
71,8
48,5
101,5
150,3
166,2
Extra per mtr.

working length*
1,8
2,4
2,4
2,9
3,9
4,7
27

TDQDDS

Triangle type 2 - male
Type
W.L.L.
S in mm
Q in mm
D in mm
H in mm
E in mm
Weight kg
DTR/10
10
180
35
100
200
320
6,3
DTR/12
12
170
40
90
200
290
7,8
DTR/15
15
300
45
150
250
440
14,4
DTR/20
20
300
50
180
300
460
19
DTR/25
25
300
55
180
300
492
23,9
DTR/30
30
300
55
180
300
492
23,9
Triangle type 2 - female

Type
W.L.L.
S in mm
Q in mm
D in mm
H in mm
P in mm
Weight kg
DSTR/10
10
180
35
100
340
100
13
DSTR/12
12
180
40
100
340
100
15,5
DSTR/15
15
250
45
150
466
120
27,2
DSTR/20
20
300
50
180
540
150
36
DSTR/25
25
300
55
180
540
150
47,5
DSTR/30
30
300
55
180
540
150
47,5
DS
D
P
S
28
Lashing information
The correct selection and use of lashings is an important issue.

Unitex is one of the worlds leading brand manufacturers fulfilling this important issue.
Fundamentals:
To the load securing of cargo transport vehicles are a row of EN 12195ff to be applied. Additional applicable in Germany
are the VDI guideline 2700ff and accident prevention rules like Stand der Technik.
The aim of load securing is: to protect the life and health of humans and animals, just as to protect the load for damaging.
The threats for the involved are mentioned in the various appendix of the EN 12195ff, so that an intended use can be guaranteed.
In Part 2 of EN 12195-2 lashing made of fibers (edition December 2000) in Appendix A, the following
Hazards listed (summary):
The load must not slip, roll over or tip over by loading, transporting and unloading due to improper load securing
The direct and indirect danger for man and animal must be ruled out.
Even the secured transportation needs to be guaranteed by the various modes of transport and among the various accelerations.
Vehicles must, taking into account the load distribution and load capacity of the loading area, connection rings, side walls, end
walls, etc., absorb the resulting forces (EN 12195-1 under 4 Acceleration).
If the transport vehicle is not in a position to take the required forces, then lashing systems according to EN 12195-2 and 3, and
tools for example anti-slip mats (UTX-ARM) are required. The variety of tools today is very large.
Unitex offers his customers not only a large and comprehensive program, but the customers can also qualify through training.
29
Lashing information
Basic information to load securing:

During the transportation process forces put pressure on the load, as well as on the individual load securing.
The mass and friction forces needs to be taken into account.
What everyone needs to know:
We make the set with an example:
We are loading a box of 10 t.
Centre of gravity is in the middle and the load is not in risk of tilting
For a concept for load securing certain procedures has to be followed.

Unitex would like to introduce an example of 4 stages:
1. stage:
a) Drivers log in into dispatch department and receive a shipper-briefings
b) Personal put on personal protective equipment
c) Make sure the floor of the load area is clean
d) Make sure intact lashing (web lashing, chain lashing, etc.) and additional tools (anti-slip mats, connecting rings etc.) is ready
e) Prepare the vehicle body for loading
2. stage:
a) Talk over the way of loading with the truck driver
b) Positioning (load dividing)of the load to be discussed with the driver
c) Under layers of wood to be placed, so that the vehicle will not be damaged by overload.
d) The way of lashing (closing form, closing force or in a combination) to be discuss with the driver
3. stage:
a) Safe putting on of the load with a crane or
b) Taking the load safely in forklift operation
c) achieve closing form to the front f.e. through vehicle set up, connection rings, under layers of wood or head sling
d) load may be dropped to anti slip mat
30
Lashing information
4. stage:
a) prepare lashings (web lashing, chain ashing, etc.) and additional tools for selected way of lashing and calculation for load securing
b) decline the load securing by the shipper
c) the driver is made aware of the fact that the load securing can be inspected along the road
d) The vehicle structure will be closed if needed
TIP: Unitex offers you the service to introduce load securing in your company.
In the 4 phases following actions are mentioned:
We load the 10t box under the load dividing on the truck.
1. Question we ask ourselves:

Which method of load securing can be used?
We make a split between form fitting and force fitting load securing.
closing form load securing:
Buttress of the load against connecting rings, front wall, side walls etc. The securing
can be made through a direct connection of the load or indirect connection of the load
due to direct lashing f.e. diagonal lashing, hypotenuse lashing, circumference lashing
and head lashing.
A closing force load securing is always pre-pulling.

closing force load securing:
50 % STF
100 % STF
Tensionforce
k-value: 1,5
Over the top lashing is a force fitting load securing. By increasing the contact pressure it prevents the load from shifting. By under
laying the anti slip mats the number of lashings can be reduced.
The number of lashing is depending on the mass (m), friction (D), lashing angle (alpha) and the
standard tension force (STF) of the lashings.
closing form and closing force load securing can be used in combination.
31
Lashing information
Important hold of the lashing:

LC:
LC = Lashing Capacity - to lash
L ashing Capacity (LC) Lashing force diagonal lashing in straight line.
f.e. LC 2000 daN
LC:
in circumference f.e. LC 4000 daN
Use by a head- and side sling
Top view
LC
SHF
STF
SHF:
Standard Hand Force = Regular manual force (50 daN)
Tension will be put on the lashing system with this force
STF:
Standard Tension Force pre tension force of the lashing system
f.e. from 250 daN up to 550 daN for polyester lashing systems
With lashing chain systems from appr.1000 daN up to 2500 daN
TIP: Practical Advice on the use of lashings systems according to EN 12195-2:

In the selection and in the use of lashing systems it is necessary to take in mind the lashing forces, as well as way of use and the
way it is working on the load.
32
Lashing information
2. Question:
How big are the expected forces?
According to EN 12195-1 the following forces contribute to road vehicles. These are calculated with support of the
acceleration coefficient.
c = acceleration coefficient
0.8 in forward road direction (x)
0.5 opposite of the forward road direction (rear direction) (x)
0.5 side ways of the forward road direction by a stable load(y)
0.7 for non-tilt secured cargo (side)
1.0 cz (vertical)
We count with a wooden box:
10t (centre of gravity in the middle and no danger for tilting)
c = acceleration coefficient
0.8 in forward road direction
10t x 0.8 = 8t secured forces forwards
0.5 oppoPage of the forward road direction (x)
10t x 0.5 = 5t secured forces in rear direction
0.5 in side way direction (y)
10t x 0.5 = 5t secured forces side ways to the direction
1.0 cz (vertical)
10t x 1.0 = 10t vertical forces (load vehicle floor)
From the practice spoken in metric tons, we need to calculate in forward direction with 8 tons of backup power, in rear
and side way direction with 5 tons securing forces.
8 tons = 8000 kg x 9.81 m/s2 = 78,480 N = 7848 daN securing forward road direction
5 t = 5000 kg x 9.81 m/s2 = 49,05 N = 4905 daN securing force in rear and side way direction
3. Question:
What must be observed with closing force load securing?
1. Example:
friction between the load and the transport vehicle with
wooden floors D = 0.3.
Lashing angle : 80 , Stf: 550 daN
Calculating the number of lashings
with over the top lashing (EN 12195-1, formula 5):
n>
(Cx,y - D * C Z) * m * g
k * D * sin() * FT
Results: We obtained a minimum number of lashings = 23 pieces of lashing

systems with Ergo ratchet - STF 550 daN Type 50A / 2
33
Lashing information
2. Example:
Anti slip mats between the load and transport vehicle with D = 0.6.
Lashing angle : 80 , Stf: 550daN
Calculating the number of lashings by over the top lashing
(EN 12195-1, formula 5):
(Cx,y - D * C Z) * m * g
n>
k * D * sin()* FT
Results:
We obtained a minimum number of lashings = 5 pieces of lashing systems with Ergo
ratchet - STF 550daN Type 50A / 2
and anti slip mats.
TIP: Due to the use of anti slip mats from Technotex you will get an secured and practical load securing.
3. closing form by two connection rings with a total blocking force of 2000 daN
Example:
Anti slip mats between the load and transport vehicle with D = 0.6.
Lashing angle: 80 , Stf: 550 daN
Calculating the number of lashings by over
the top lashing (EN 12195-1, formula 5):
n>
(Cx,y - D * C Z) * m * g
k * D * sin()* FT
Results:
With the blocking force forwards with 2000 daN, we obtain a
minimum number of lashing systems= 2 pieces of lashing systems with Ergo ratchet
- STF 550 daN Type 50A/2.und 2 pieces anti slip mats
Caution: The principle: By over the top lashing always use at least 2 lashing systems
Result of the load securing:
Example 2 and 3 can be implemented well in practice with products from Technotex. Still some important indications has to be
respected!
As a special service Technotex offers a CD-Rom.

This specially developed calculation program is a
important tool for identifying the necessary
number of lashing systems.
34

25mm lashings with Ratchets
Type
1 or 2
part
Lashing capacity
Standard Tension Nr. of the endForce (STF ) by SHF fitting

50 daN
25B/1
1- part
800 daN
STF 240 daN
25B/2
2- parts
400 daN
STF 120 daN
Type
1 or 2
part
Lashing capacity

50 daN
25A/1
1- part
1500 daN
STF 270 daN
25A/2
2-part
750 daN
STF 135 daN
2, 3, 4, 5, 8, 10
3, 4, 5, 10
Tv approval for lashings with hook No. 2 and 3
10
10
*Maximum Lc Capacity
340 daN
Art.nr 23.208
Art.nr 23.207
Art.nr 23.301
Art.nr 23.525
Art.nr 23.219
Art.nr 23.229
Art.nr 23.204
35

25mm lashings with cambuckle
36
Type
1 or 2
part
Lashing capacity
IG25/1
1-part
250 daN
IG25/2
2-parts
125 daN
Standard Tension Nr. of the

Force (STF ) by SHF endfitting
50 daN
2, 3, 4, 5, 8, 10
10
10
Art.nr 23.208
Art.nr 23.207
Art.nr 23.301
Art.nr 23.525
Art.nr 23.219
Art.nr 23.229
Art.nr 23.204

35mm lashing with Ratchets
Type
1 or 2 part Lashing capacity

50 daN
35B/1
1-part
2000 daN
STF 360 daN
35B/2
2-parts
1000 daN
STF 180 daN
Type
1 or 2
part
Lashing capacity

50 daN
35A/1
1-part
3000 daN
STF 360 daN
35A/2
2-parts
1500 daN
STF 180 daN
1, 2, 3, 4, 5*, 10*
1, 2, 3, 4, 5*
Art.nr 23.305
Art.nr 23.303
Art.nr 23.202
Art.nr 23.301
10
750 daN
750 daN
Art.nr 23.525
Art.nr 23.204
37

35mm lashings with cambuckle
38
Type
1 or 2
part
Lashing capacity
IG35/1
1-part
500 daN
IG35/2
2-parts
250 daN

50 daN
1, 2, 3, 4, 5, 10
10
Art.nr 23.305
Art.nr 23.303
Art.nr 23.202
Art.nr 23.301
Art.nr 23.525
Art.nr 23.204

Type

50 daN
50L/1
1-part
2000 daN
STF 360 daN
50L/2
2-parts
1000 daN
STF 180 daN
Type

50 daN
50C/1
1-part
3000 daN
STF 420 daN
50C/2
2-parts
1500 daN
STF 210 daN
Art.nr 23.526
Art.nr 23.531
1, 2, 3, 5*, 6, 7,
8, 9
1, 2, 3, 5*, 6, 7,
8, 9
750 daN
Art.nr 23.502
Art.nr 23.506
Art.nr 23.527
Art.nr 23.528
Art.nr 23.532
Art.nr 23.525
39

50mm lashings 1-part with cambuckle
40
Type
1 or 2
part
Lashing capacity
IG50/1
1-part
1200 daN
IG50/2
2-parts
600 daN

50 daN
1, 2, 3, 4, 5, 6,
7, 8, 9
Art.nr 23.502
Art.nr 23.506
Art.nr 23.532
Art.nr 23.301
Art.nr 23.525
Art.nr 23.526
Art.nr 23.531
Art.nr 23.527
Art.nr 23.528
50mm lashing 2000/4000 daN

systems
Type
1 or 2
part
Lashing capacity

50 daN
50BS/1
1-part
4000 daN
STF 400 daN
50BS/2
2-parts
2000 daN
STF 200 daN
Type
1 or 2
part
Lashing capacity

50 daN
50B/1
1-part
4000 daN
STF 640 daN
50B/2
2-parts
2000 daN
STF 320 daN
1, 2, 3, 6, 7, 8, 9
1, 2, 3, 6, 7, 8, 9
Art.nr 23.502
Art.nr 23.506
Art.nr 23.532
Art.nr 23.526
Art.nr 23.531
Art.nr 23.527
Art.nr 23.528
41

systems
50mm lashings with Long-handle ERGO Ratchets
Type
1 or 2
part
Lashing capacity

50 daN
50BE/1
1-part
4000 daN
STF 960 daN
50BE/2
2-parts
2000 daN
STF 480 daN
1, 2, 3, 6, 7, 8, 9
50mm lashings with easy release Ratchets

Type
1 or 2
part
Lashing capacity

50 daN
50BER/1
1-part
4000 daN
STF 800 daN
50BER/2
2-parts
2000 daN
STF 400 daN
42
Art.nr 23.502
Art.nr 23.506
Art.nr 23.532
Art.nr 23.526
Art.nr 23.531
Art.nr 23.527
Art.nr 23.528
1, 2, 3, 6, 7, 8, 9

systems
Type

50 daN
50AS/1
1-part
5000 daN
STF 500daN
50AS/2
2-parts
2500 daN
STF 250 daN
Type

50 daN
50A/1
1-part
5000 daN
STF 700 daN
50A/2
2-parts
2500 daN
STF 350 daN
1, 2, 3, 6, 7, 8, 9
1, 2, 3, 6, 7, 8, 9
Art.nr 23.502
Art.nr 23.506
Art.nr 23.532
Art.nr 23.526
Art.nr 23.531
Art.nr 23.527
Art.nr 23.528
43

systems
50mm lashings with Long-handle ERGO Ratchets
Type
1 or 2
part
Lashing capacity

50 daN
50AE/1
1-part
5000 daN
STF 1100 daN
50AE/2
2-parts
2500 daN
STF 550 daN
1, 2, 3, 6, 7, 8, 9
50mm lashings with easy release Ratchets
Type
1 or 2
part
Lashing capacity

50 daN
50AER/1
1-part
5000 daN
STF 800 daN
50AER/2
2-parts
2500 daN
STF 400 daN
44
Art.nr 23.502
Art.nr 23.506
Art.nr 23.532
Art.nr 23.526
Art.nr 23.531
Art.nr 23.527
Art.nr 23.528
1, 2, 3, 6, 7, 8, 9
75/100 mm lashing systems

75mm lashing with ratchet
Type
1 or 2
part
Lashing capacity

50 daN
75A/1
1-part
10000 daN
STF 1000 daN
75A/2
2-parts
5000 daN
STF 500 daN
2, 3, 9
100mm lashing with ratchet

Type
1 or 2
part
Lashing capacity

50 daN
100A/1
1-part
10000 daN
STF 1000 daN
100A/2
2-parts
5000 daN
STF 500 daN
Art.nr 23.702
Art.nr 23.701
Art.nr 23.704
2, 3, 9
45
Lashings hooks
Lashing hooks (parts)
Art.nr 23.207
25mm Double J hook

for lashing system sb25A and B
Maximum LC Capacity 750 daN

Art.nr 23.540
Art.nr 23.303
Art.nr 23.305
Art.nr 23.204
Art.nr 23.505
Art.nr 23.704
Art.nr 23.527
50mm D-Ring
MBL 5000 kgs
for lashing systems SB50A And B
Maximum LC capacity 2500 daN
46
Art.nr 23.502
Art.nr 23.525
Art.nr 23.531
Art.nr 23.301
Forged Hook with Keeper
MBL 2500 kgs
for lashing systems SBIG, SB25
SB35B
12
Art.nr 23.558
50mm Flat D-Ring
MBL 5000 kgs
for lashing systems SB50A and B
Art.nr 23.702
75mm U-Hook
MBL 10000 kgs
for lashing system SB75A

10
Art.nr 23.229
25mm S-hook
MBL 680 kgs
for lashing system SBIG25
Art.nr 23.526
50mm Twisted Snap Hook
MBL 5000 kgs
50mm Forged Flat Hook

MBL 5000 kgs
75mm Triangel Forged Hook

MBL 10000 kgs
for lashing systems SB75A

50mm end track spring fitting

MBL 1500 kgs
for lashing systems SBIG35,
SBIG50 SB25A and B
SB35B SB50C
50mm Flat Snap Hhook

MBL 5000 kgs

Art.nr 23.506
Art.nr 23.208
25mm U-Hook
MBL 1000 kgs
for lashing system IG25 and SB25B
50mm single J-hook

MBL 5000 kgs
25mm S-Hook
MBL 1500 kgs
for lashing systems SBIG35,
SBIG50, SB25A and B
11
50mm U-hook
MBL 5000 kgs
35mm single J-hook

MBL 3000 kgs
10
Art.nr 23.701
Art.nr 23.532
50mm Double J hook
MBL 5000 kgs
and SB50A
75mm Double J hook

MBL 10000 kgs
Maximum LC Capacity
5000 daN

35mm U-hook
MBL 3000 kgs
35mm Double J hook

MBL 3000 kgs

50mm Double J hook with

keeper
MBL 5000 kgs
Art.nr 23.202
Art.nr 23.528
50mm Triangel Forged Hook
MBL 5000 kgsfor lashing systems
SB50A And B
Art.nr 23.219
25mm D-Ring
MBL 800 kgs
for lashing systems SBIG25
and B25B
Ratchets
Ratchets
Art.nr 23.706
75mm Ratchet
for system sb75

Art.nr 23.503
Art.nr 23.315
Art.nr 23.316
Art.nr 23.524
50mm Cambuckle
for system sbig50

Art.nr 23.314
Art.nr 23.201
Art.nr 23.300
35mm Cambuckle
for system sbig35
Art.nr 23.202
25mm Ratchet
for system sb25A
25mm Ratchet
for system sb25B
Art.nr 23.504
50mm Ligth Duty Ratchet
for system sb50L
35mm Ratchet
for system sb35B

25mm Stainless steelRatchet

for system sb25A

Art.nr 23.507
Art.nr 23.513
50mm Easy-Release-Ratchet
for system sb50A and B

50mm Short- Ratchet


35mm Ratchet
for system sb35A

50mm Ergo-Ratchet

50mm Ratchet

Art.nr 23.509
Art.nr 23.203
25mm Black Ratchet
for system sb25B
Art.nr 23.218
25mm Cambuckle
for system sbig25
47
One Way Lashing

The UNIFIXX One-way lashing systems offers a lashing solution by combining low cost with safe
transport.
The UNIFIXX solution is much better than the traditional way of securing loads and over the last decades
it has replaced traditional products such as ropes and chains. The UNIFIXX one-way lashing systems are
light weight load securing solutions avoiding damage risk on heavy and expensive loads. Our high tenacity
products are extremely suitable for securing loads on crates, pallets, in containers, flattracks and on
wagons. The UNIFIXX One-way lashing webbing is supplied in combination with buckles and tensioners.
The UNIFIXX One-way lashing systems are approved by the Germanischer Lloyd, one of the toughest
appprovals. The allowable working loads vary from 500daN to 4.000 daN with a width variation from
30mm to 50mm. The lashings are produced in-house ensuring a high flexibility regarding individuals
wishes. UNIFIXX can be manufactured, personalized and packed to your individual specifications.
Type
Width (mm)
MBS Lashing
(daN)
Packing
(plastic bags)
System Strength
(daN)- Buckle
W323
32
2300
250 mtr.
4000 - B3030
W435
40
3500
200 mtr.
6000 - B4040
W450
40
5000
200 mtr.
7500 - B4040
W523
50
2300
300 mtr.
3000 - B5020
W550
50
5000
200 mtr.
9000 - B5050
W560
50
6000
150 mtr.
9500 - B5050
W575
50
7500
150 mtr.
10000 - B5050
Type
Width (mm)
B3030
30
B4040
40
B5050
50
B3030S
30
B5020
50
B4050W
50
B5050W
48
H5050
50
SB10-7
32 mm
SB12-7
40 mm
SB12-8
40 mm
SBF10-7
32 mm
SBF12-7
40 mm
SBF12-8
40 mm
TENSH26
PTENS01
UR5050
One Way Lashing

User instructions Unifixx One Way Lashing
1
Thread one end of the lashing webbing

through the middle of the buckle
Make a loop around one end and

insert the lashing webbing under
the looped end
Repeat step 1 - 4 with the

opposite end
Squeeze the handle of the tensioner

and lead the webbing under the
break lever
Pull the handle wide open and place

the top lashing webbing part through
the cutter and tensioner slot
11
Lead the end back through the

middle of the buckle
Pull the lashing webbing away

from the buckle
10
Pull tight and allow a min. overlap

of 25 cm for tensioner use
Move the handle up and down to

tension the lashing webbing; keep
min. 8 cm overlap from the buckle
12
Squeeze the handle to cut the lashing webbing (10), release the break (11) and remove the tensioner (12)
49
Unitex Anti slip matting

Anti slip matting for load securing
The safe loading of vehicles is vitally in prevending injury to people and damage of property when transporting a load the
load must be restrained tidily and safely is order to prevent the load from shifting during transport The load is required to
withstand forces of at least:
80% of its weight in forward direction (braking)
50% of its weight sideways and backwards (acceleration and cornering).
20% of the weight in upwards direction ( rough roads)
Load-securing with Polyester or chain lashing is not always sufficient especially when there is low friction between
the load and baering surface at full stop surface Load restraint equipment is most efficient when there is high friction
between the vehicle and the load surface, for this you need appropriate inter layer packing. Unitex has specially
designed anti-slip rubber matting for interlayer packing UTX-ARM which increases the friction between the two
surfaces. In fact this UTX-ARM anti slip matting should belong to the standard equipment for every responsible and
professional transporter.
Unitex UTX-ARM Anti slip matting increases the friction between the surface up to at least 0,6 as a result the load can
be restrained with fewer lashings because you need less tension or lashing force to secure the load
Unitex UTX-ARM anti slip matting is also very useful for loads which cant withstand high pressure or tension forces
50
Unitex Anti slip matting

Anti slip matting special for concrete parts (UTX-ARM-9510RHS)
Unitex anti slip matting on rubber basis is special developed for concrete parts The coloured anti slip matting does not give of and
therefore is suitable for the use on concrete
Type
Colour
messurements
thickness
standard size
Material
UTD-ARM-9510RHS
Multicoloured
on rolls or cutted lengthes
from 3 mm
up to
20 mm
Rolls 250 x 8 x
5.000 mm
rubber
based matts
abrasion
restistance
( > 0,6)
FE: For rolls Rollenware 250mm x 8mm x 5.000 mm

UTD-ARM-9510RHS-02500805000
Anti slip Matting for load restraining (UTX-ARM-7210)

Unitex anti slip matting on a synthetic rubber basis (SBR/SNR) is special designed for professional load restraining Due to the black
granulate mix we are able to achieve a sliding resistance of more than 0,7 The Unitex anti slip matting is tested and certified by a
independent test institute BIA ( Berufsgenossenschaft im BG-PRFZERT institute fr Arbeitssicherheit)
Type
Colour
messurements
thickness
standard size
Material
UTD-ARM-7210
Black
on rolls or cutted lengthes
from 3 mm
up to
20 mm
Rolls 250 x 8 x
5.000 mm
on SBR/
NBR-Basis
with a
extreme
high
abrasion
resistance
( > 0,7)
FE: For rolls Rollenware 250mm x 8mm x 5.000 mm

UTD-ARM-7210-02500805000
51
Professional securing system for timber deck cargo

(in compliance with IMO 275E
Code of Safe Practice for Ships Carrying Timber Deck Cargoes)
Specifications:
Safe working load
: 133 kN
MBL
: 200 kN
Temperature range
: of 40C to +100C
Weight
: 10 kg
Webbing

: Polyester < 5% elongation,

measured from the pre-tension load
of 27 to 106.4 kN
Width
: 100 mm
Take up
: + 2 m Handling
Certificates
: Germanischer Lloyd
End connectors : hook, shackles or customised
Minimum pre-tension
: 2.700 kg
Maintenance
Length
The main advantages of Turtle Max timber lashing systems are:
load restraint using a tensioning device (ratchet)

effective and safe control of load whilst in transportation
extremely and efficient tie-down and release of load thus saving time
no damage to the load being tied down
52
: variable
: one man operation
: very low

Single and double winch arrangement.
single winch arrangement
double winch arrangement
Components of each system

1 x Ratchet Winch
1 x Web band 100% PES, fixed end / 1 reinforced eye / 1 soft eye
1 x Web band 100% PES, loose end / 1 reinforced eye / 1 open end
2 x shackles
Components of each system

2 x Ratchet Winch with 1 steel adapter each
1 x Web band 100% PES, loose end, variable length
2 x Edge controller (web band protector) - Optional
Lashing arrangement for unitized/packaged timber
Lashing arrangement for unitized/packaged timber
Lashing arrangement for logs
Lashing arrangement for logs
53
Ratched handle with

32 mm box spanner
Specification
Light weight design
IMO-lever hot dip galvanized
High quality stainless steel ratchet
One set consists of two ratchets and one extension
Low budget solution for narrow working space is available on request
Specifications Turtle Max Timber Lashing System, single winch arrangement

M.S.L
KN
Test Load
KN
M.B.L.
KN
PCS
Turtle Max Web system

TurtleWinch
Nrs: 043401 - 043410
2 x Connector bolt and nut,
lock and slip device, tensioner
100
95
200
10
Turtle fixed Side strop

L=2.00 m
PW 100/240 semi Duplex
fl.cyc/flcyc 0,35 m
100% Polyester, t = 5 mm
140
95
220
10
Turtle Variable Side strop

L=23.00 m
PW 100/240 semi Duplex
fl.cyc/flcyc 0,35 m
100% Polyester, t = 5 mm
140
95
220
10
Timber Max Lashing Shackle

Red-Pin galvanized
Pin 25 mm/ Bow 19 mm
140
95
270
20
Specification of Item
54
AirMaxx Dunnagebags
AirMaxx bags used for transport of forrest products and

break-bulk, eliminate damage caused by cargo shifting. Once
inserted into empty space, the AirMaxx bags are inflated with
compressed air. AirMaxx bags adapt themselves to almost any
shape, space or void.
Due to the high filling presure the AirMaxx bags move the cargo
to reduce the number of small voids.
The AirMaxx Bag is very easy to handle, even for one person. Only
a few minutes per bag is required for installation, thus eliminating
the need for carpenters, timber and extra dock time.
AirMaxx is manufactured of a new durable and lightweight
synthetic material. The small weight and small size after deflation
simplify storage. AirMaxx is re-usable. Proper operation is
guaranteed for one year. One year guarantee on seams and valves.
Paper reels , vertical stowage :

Every horizontal layer is lashed on the front and aft by lashing chains secured to the fixed lashing points
in the holds sides. The reels are protected by timber. Dunnage bags are used in the upper layer of reels
to fill up gaps and to avoid any movement between the reels.(subtr. CSM papercarrier)
FOUR EASY STEPS TO A TOTALLY
PROTECTED CARGO
EN
RV
AI
1. When deflated the dunnage bag is easy to load between sections.

2. Fill bag until load is secured and space completely filled.
3. Load will remain set.
4. Deflate and remove after shipment.
OTHERS
Specifications
Size empty
: 100 x 130 en 100 x 200 cm
Take up
: 55 cm
Handling
: one man operation
Automatic fillstop
: 60 80 Kn/m
Temperature
: -25 C to + 50 C
Weight
: 4.5 kg
Maintenance
: very low
Width
: 100 cm
Guarantee
: 2 year on welded seems
Length
: 100 500 cm
EN
RV
AI
AIRMAXX
55
AirMaxx Dunnagebags
1
2
ITEM
QTY.
PART NO.
DESCRIPTION
01-001
Mafa quickconnector
01-001
PVC hose / fill
01-001
Automatic fillstop
01-001
Release stop
01-001
Outerbag
01-001
Innerbag
SCALE
TITLE
1: 10
1.20
Drw no 1.01
AirMax Dunnagebag
REV.
DESCRIPTION
DATE
for internal approval
13-10-2004
FILENAME
AIRBAG 2003 DRW 1.VSD
BY
DRAWN BY
J.D. Kaptein
1.00
56
Contents protection materials
UP Protection sleeves
UPSP Corner protection
UPCP Corner protection
PU Technical information
Purtecta Color
PU-Sleeve
PU Coating
PU Cornerprotection
PU Chain protection
Protection Sleeve
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
58 - 59
60
61
62 - 63
64
65 - 66
67
68 - 69
70
71
57
ULTRAPROTECT
ULTRAPROTECT protection sleeves for UNITEX web slings

heavy duty uphd and light duty upld
Webbing width in mm
webbing layers
ultraprotect light duty
ultraprotect heavy duty
can aswell stitched as loose on the webbing
can only be stitched on a 2-ply web sling
30
UPLD-65
UPHD-65
30
UPLD-65
UPHD-65
50
UPLD-65
UPHD-65
50
UPLD-65
UPHD-65
60
UPLD-75
UPHD-75
60
UPLD-75
UPHD-75
75
UPLD-90
UPHD-90
75
UPLD-90
UPHD-90
90
UPLD-115
UPHD-115
90
UPLD-115
UPHD-115
100
UPLD-115
UPHD-115
100
UPLD-125
UPHD-125
120
UPLD-145
UPHD-145
120
UPLD-145
UPHD-145
125
UPLD-145
UPHD-145
125
UPLD-145
UPHD-145
150
UPLD-175
UPHD-175
150
UPLD-175
UPHD-175
180
UPLD-205
UPHD-205
180
UPLD-205
UPHD-205
200
UPLD-275
UPHD-275
200
UPLD-275
UPHD-275
250
UPLD-275
UPHD-275
250
UPLD-275
UPHD-275
300
UPLD335
UPHD-335
300
UPLD335
UPHD-335
UPLD - 65 =(U)ltra(P)rotect (L)igth (D)uty 65 mm inside width
58
Dyneema
is a registered
trademark of
Royal DSM N.V.
ULTRAPROTECT
ULTRAPROTECT protection sleeves for uniTex round slings

heavy duty uphd and light duty upld
Dyneema
is a registered
trademark of
Royal DSM N.V.
Tons
Over the single leg
1t
UPLD-65 / UPHD-65
UPLD-65 / UPHD-65
Over both legs
2t
UPLD-65 / UPHD-65
UPLD-65 / UPHD-65
3t
UPLD-65 / UPHD-65
UPLD-65 / UPHD-65
4t
UPLD-65 / UPHD-65
UPLD-75 / UPHD-75
5t
UPLD-75 / UPHD-75
UPLD-75 / UPHD-75=tide / UPLD-90 / UPHD-90 =loose
6t
UPLD-75 / UPHD-75
UPLD-90 / UPHD-90
8t
UPLD-115 / UPHD-115
UP-90=fest / UPLD-115 / UPHD-115=lose
10 t
UPLD-115 / UPHD-115
UPLD-115 / UPHD-115
12 t
UPLD-115 / UPHD-115
UPLD-145 / UPHD-145
15 t
UPLD-125 / UPHD-125
UPLD-145 / UPHD-145
20 t
UPLD-125 / UPHD-125
UPLD-145 / UPHD-145=fest / 100 -UPLD-175 / UPHD-175=lose
25 t
UPLD-145 / UPHD-145
UPLD-175 / UPHD-175
30 t
UPLD-175 / UPHD-175
UPLD-220 / UPHD-220
35 t
UPLD-175 / UPHD-175
UPLD-220 / UPHD-220
40 t
UPLD-175 / UPHD-175
UPLD-220 / UPHD-220
50 t
UPLD-220 / UPHD-220
UPLD-275 / UPHD-275
60 t
UPLD-220 / UPHD-220
UPLD-275 / UPHD-275
70 t
UPLD-335 / UPHD-335
UPLD-335 / UPHD-335
80 t
UPLD-335 / UPHD-335
90 t
UPLD-335 / UPHD-335
100 t
UPLD-335 / UPHD-335
UPLD - 65 =(U)ltra(P)rotect (L)igth (D)uty 65 mm inside width
59
UPSP Corner protection

The ULTRAPROTECT Sling Protection is specially developed for round- and web slings in order to protect this lifting equipment
against extreme abrasion or sharp edges.
The ULTRAPROTECT sling protection is made of the Dyneema fibre, which makes the ULTRAPROTECT sling protection both very
light, and extremely resistant against abrasion and sharp edges
Due to the firm Velcro closing this product is very practical in use and very quick to fit and adjust.
The Velcro closing enables the user to use one single ULTRAPROTECT sling protection for a various types round slings,(1 leg or 2
legs), web slings or other lifting equipment.
The ULTRAPROTECT sling protection is available is various sizes.
For extreme abrasion applications the light duty version is applicable. To protect the lifting slings against sharp edges the heavy
duty is the perfect product.
Note: Avoid sliding of the load. Also ULTRAPROTECT can be cut through sliding.
ULTRAPROTECT SLING PROTECTION (UPSPLD)

Light duty
Type
inside width
max. in mm
UPSPLD-90 mm
85 - 87,5 mm
55,7
UPSPLD-115 mm
105 - 112,5 mm
71,7
UPSPLD-125 mm
115 - 122,5 mm
78,0
UPSPLD-145 mm
135 - 142,4 mm
90,8
UPSPLD-175 mm
165 - 172,5 mm
109,9
UPSPLD-205 mm
195 - 202,5 mm
129,0
UPSPLD-275 mm
265 -272,5 mm
173,6
UPSPLD-335 mm
325 - 332,5 mm
211,8
ULTRAPROTECT SLING PROTECTION (UPSPHD)

Heavy Duty
Type
60
inside width
max. in mm
UPSPHD-90 mm
85 - 87,5 mm
55,7
UPSPHD-115 mm
105 - 112,5 mm
71,7
UPSPHD-125 mm
115 - 122,5 mm
78,0
UPSPHD-145 mm
135 - 142,4 mm
90,8
UPSPHD-175 mm
165 - 172,5 mm
109,9
UPSPHD-205 mm
195 - 202,5 mm
129,0
UPSPHD-275 mm
265 -272,5 mm
173,6
UPSPHD-335 mm
325 - 332,5 mm
211,8
Dyneema
is a registered
trademark of
Royal DSM N.V.
UPCP Corner protection

ULTRAPROTECT CORNER PROTECTION
Unitex has developed a new and unique flexible corner protection
This new flexible corner protection made out of a High Tech Dyneema
fiber adjusts itself almost 100% to the shap of the corner. The material is
very cut and abrasion resitant.
The material used for the corner protection has proven itself already in
our ULTRALIFT round slings especially on the ULTRALIFT UPNG coil sling

ULTRAPROTECT CORNER PROTECTION FOR UNITEX ROUND SLINGS (UPCP)
Type
suitable for:
suitable for:
UNITEX ROUNDSLING
UNITEX WEBSLINGS
Type
Width A
Length B
Width C
inmm
in mm
in mm
UPCP65/200
1,2 and 3 ton
30 mm
65
200
50
UPCP75/250
4,5 and 6 ton
60 mm
75
250
50
UPCP85/300
75 mm
85
300
50
UPCP100/300
90 mm
100
300
50
UPCP125/300
8t
100- 120 mm
125
300
50
UPCP 135/300
10 t - 12 t
125 mm
135
300
50
UPCP155/500
15 t
150 mm
155
500
50
UPCP 185/600
20 t -25 t.
180 mm
185
600
75
UPCP 215/600
30 t
200 mm
215
600
75
UPCP 230/800
35 t - 40 t
230
800
75
UPCP 285/800
45 t - 55 t
250 mm
285
800
100
UPCP 345/800
60 t - 65 t
300 mm
345
800
100
UPCP 370/800
70 t - 75 t
370
800
100
UPCP 430/800
80 t
430
800
100
UPCP 460/800
85 t
460
800
100
UPCP 540/800
90 t - 100 t
540
800
100
UPCP 690/800
125 t
690
800
100
C
A
UPCP - 215 =(U)ltra(P)rotect (C)orner (P)rotection 215 mm wid
Dyneema
is a registered
trademark of
Royal DSM N.V.
A
B
Typ 1
Typ 2
61
Mechanical properties
Distinguishing Characteristics
Measurements
dimensions
standard
Shore-A Hardness
80 3
Tensile strength
20
N/mm2
DIN 53504
Ultimate elongation
450
DIN 53504
Tear resistance
20
N/mm
DIN 53515
Attrition
60
mg
DIN 53516
Rebound elasticity
ca. 40
DIN 53505
Chemical properties
Chemical resistant on Unitex PU- protection material tested on a sample after 200 hours exposure at 20 degrees Celsius.
Short time exposure has normally little influence and is not comparable for following data
Concentration
Formic acid
degeneration of the
mechanical Properties
degeneration of the
mechanical Properties
2%
1)
lactic acid
45 %
2)
5%
2)
Caustic Soda
10 %
2)
10 %
2)
40 %
2)
Ammonia
5%
1)
50 %
3)
Boric acid
4%
1)
25 %
2)
chlorine-alkali
3%
1)
50 %
2)
acetic acid
2%
1)
hydrochloric acid
10 %
3)
5%
2)
nitric acid
10 %
1)
10 %
2)
sulphuric acid
10 %
1)
50 %
3)
25 %
2)
Formaldehyde
37%
3)
50 %
3)
gerb acidic solution
20 %
1)
Soda
20 %
2)
Potassium
20 %
3)
premium gasoline
saline drip
10 %
1)
hydrogen peroxide
Linseed oil acid
1)
xylene
Methanol
3)
citric acid
10 %
3)
methyl chloride
3)
sugar solution
30 %
1)
1) = degeneration of the mechanical properties 0 - 5%

2) = degeneration of the mechanical properties 5 - 15%
3) = degeneration of the mechanical properties > 15%
62
Concentration
phosphoric acid
3)
10 %
1)
3)
By using Unitex PU-protection the user still has his or her reponsibility,
care should be taken to ensure the safety of the lift and personnel during the lift
Unitex Pu-protection sleeve can be used between 0 up to 70 degrees celcius
(for a short periode only between -40 and plus 100 degrees celcius)
Maximum pressure allowed is 30N/mm2
Chemicals can effect the Polyurethane special attention is needed and the producer must be contacted
Do not dry the sleeve by force
store the Polyurtethane in a dry and ventilated room
Please note that the Polyurethane can be damaged when goods start to slide through the sleeve. The user is always
responsable for the correct use of the sling protected with a polyurtethane coating or sleeve
63
Purtecta Color
PU-coating with colour-code
PURTECTA colour web slings. A new development by Unitex

PURTECTAcolor web slings is a combination of 2 special coatings. On one side (special
for loads with sharp edges) the PURTECTA web slings have a thick and more extensive
PU coating and the other side a special emulsion coating with a colour-code according
to EN 1492-1 for an extra protection on abrasion
The PURTECTAcolor colour web slings are special for use
under following circumstances:
1.
2.
3.
4.
+ : Cut resistance combinated with flexibility of the sling

+ : Light in weight therefore easy to use
+ : Extremely cut and abrasion resistant
+ : Very mild gentle for the load ( no damages)
A unique new innovation by Unitex to make protected slings easier and safer in use
PURTECTAcolor - web slings EN 1492-1

Type
colour-code according EN 492-1
WLL in t
colour-code according EN 492-1
BPTC-30
violet
1,0
30
BPTC-60
green
2,0
60
BPTC-90
yellow
3.0
90
BPTC-120
grey
4,0
120
BPTC-150
red
5,0
150
BPTC-180
brown
6,0
180
BPTC-240
blue
8,0
240
BPTC-300
orange
10,0
300
BPTC-300/3
orange
15,0
300
BPTC-300/4
orange
20,0
300
pink
Intermediate
PU-emulsion coating with colour-code according EN 1492-1

f.i green = WLL 2t.
patent pending
Load bearing surface
64
PU-Sleeve
Dimensions
Typ BVE
Typ BVD
W
Typ
dimensions
for 2-ply
webslings
for 4 ply
webslings
for
lashings
for roundslings
1 leg
for roundslings
both legs
2 t.
1 t.
8 t.
2 t.
A/I/H/W
BVE oder BVD 35/12
45/35/12/5
BVE oder BVD 40/10
50/40/10/5
BVE oder BVD 40/20
50/40/20/5
BVE oder BVD 50/12
60/50/12/5
BVE oder BVD 60/4
66/60/4/3
BVE oder BVD 60/12
70/60/12/5
BVE oder BVD 60/17
70/60/17/5
BVE oder BVD 70/12
80/70/12/5
BVE oder BVD 75/17
85/75/17/5
60mm
BVE oder BVD 70/24
80/70/24/5
60mm
BVE oder BVD 85/12
95/85/12/5
BVE oder BVD 85/24
95/85/24/5
25mm
30mm
35mm
30mm
40mm
50mm
50mm
50mm
60mm
75mm
75mm
75mm
BVE oder BVD 100/12
110/100/12/5
BVE oder BVD 100/17
110/100/17/5
90mm
BVE oder BVD 100/24
110/100/24/5
90mm
BVE oder BVD 110/12
120/110/12/5
BVE oder BVD 120/17
130/120/17/5
BVE oder BVD 120/36
130/120/36/5
BVE oder BVD 125/17
135/125/17/5
BVE oder BVD 135/12
145/135/12/5
BVE oder BVD 135/17
145/135/17/5
120mm
BVE oder BVD 135/24
145/135/24/5
120mm
90mm
3 t.
100mm
100mm
10 t.
120mm
4 t.
120mm
1:
2:
65
PU-Sleeve
Dimensions
Typ
dimensions
for 2-ply
webslings
for 4 ply
webslings
for
lashings
for roundslings
1 leg
for roundslings
both legs
A/I/H/W
BVE oder BVD 150/36
160/150/36/5
15 t.
BVE oder BVD 150/48
160/150/48/5
20 t.
BVE oder BVD 160/12
170/160/12/5
BVE oder BVD 160/17
170/160/17/5
150mm
BVE oder BVD 160/24
170/160/24/5
150mm
BVE oder BVD 180/12
190/180/12/5
BVE oder BVD 180/17
190/180/17/5
BVE oder BVD 190/12
200/190/12/5
BVE oder BVD 190/17
200/190/17/5
180mm
BVE oder BVD 190/24
200/190/24/5
180mm
BVE oder BVD 200/17
210/200/17/5
BVE oder BVD 220/12
230/220/12/5
BVE oder BVD 220/17
230/220/17/5
BVE oder BVD 220/36
230/220/36/5
BVE oder BVD 220/45
230/220/45/5
BVE oder BVD 240/20
250/240/20/8
BVE oder BVD 250/15
260/250/15/8
240mm
BVE oder BVD 260/17
270/260/17/8
250mm
BVE oder BVD 280/15
290/280/15/8
BVE oder BVD 280/30
290/280/30/8
BVE oder BVD 320/15
330/320/15/8
BVE oder BVD 320/30
330/320/30/8
BVE oder BVD 320/45
330/320/45/8
150mm
6 t.
180mm
8 t.
200mm
200mm
10 t.
240mm
15 t.
300mm
300mm
20 t.
1:
Standard length in 2 and 4 meter
Prices will be charged on 0,5 meter length minimum length charged is 1 meter
extra for length under 2 meter 6%
extra for length between 2 and 4 meter 8%
extra for length from 4 meter up to maximum of 8 meter 12%
66
2:
PU Coating
POLYURETHANE COATING
Available for webslings from 30mm up to 300mm in as well 1 and 2 sided coating
The thickness of the coating is 5mm
Please note: coating of 1 -ply webslings is not possible
Coating of endless liftings slings will have a surcharge of 24%
Please note: PU-coating is not suitable for turning scharp edges Objects
Even Unitex PU-protection can be damaged when goods start to slide on the sleeve or coating
The user is always responsible for the correct use of the sling protected with a polyurtethane coating or sleeve
Typ BCE
Typ BCD
Band
Band
Special
webslings with D or DS fittings can be coated around the fittings in the way the fittings can still be moved or in such
way the fittings will be fixed to the sling
Webslings with eyes can be coated into the eyes
POLYURETHANE SPRAY COATING
Available for webslings from 30mm up to 300mm in as well a 1 and 2 sided coating
The thickness of the caoting is 0,5- 1mm
Lose webbing can be spray coated on rollls with a minmum length of 50 meter
Typ BCSE
Band
Typ BCSD
Band
67
PU Cornerprotection
POLYURETHANE KW CORNER PROTECTION WITH OR WITH OUT MAGNETS
Type
90
for webbing
width (b) in mm
number of
magnets
KW025
25
KW040
40
KW065
65
KW075
75
KW100
100
KW125
125
KW150
150
KW200
200
KW300
300
Other sizes are available on demand
R100
30
Type
for webbing
width (b) in mm
number of
magnets
KWLG060
60
KWLG090
90
KWLG150
150
KWLG300
300
UNITEX KWL CORNER PROTECTION
Type
for webbing width (b)

in mm
H (mm)
Ha
(mm)
KWL030
30
100
40
50
10
20
KWL060
60
100
70
80
12
30
KWL090
90
100
100
110
12
30
KWL120
120
100
135
145
12
30
KWL150
150
150
160
170
12
30
KWL180
180
150
190
200
12
30
KWL240
240
200
280
300
15
40
KWL300
300
200
320
340
20
45
H
H
68
B
B
L (mm)
B (mm) Ba (mm)
PU Cornerprotection
UNITEX KWLG CORNER PROTECTION
for webbing
width (b) in mm
Type
Joint
number of
magnets
KWLG060
60
KWLG090
90
KWLG150
150
KWLG300
300
Magnet
Perforated sheet
UNITEX DF CORNER PROTECTION
ah
l
Type
Length x Width
opening a x b
DF025
250 * 80
25 * 10
DF035
250 * 80
35 * 10
DF055
300 * 100
55 * 10
DF060
450 * 100
60 * 30
DF070
450 * 120
70 * 30
DF080
450 * 120
80 * 30
DF090
470 * 130
90 * 40
DF100
470 * 150
100 * 40
DF110
470 * 150
110 * 40
DF130
470 * 170
130 * 40
DF160
470 * 200
160 * 40
DF200
470 * 240
200 * 40
DF220
470 * 240
220 * 40
DF250
500 * 280
250 * 40
DF320
600 * 400
320 * 40
DF420
600 * 500
420 * 40
69
PU Chain Protection
PU chain protection sleeve BVC
Type
Material Thichness w
Inside Diameter Di
outside dimensions a * b
BVC 22/12
5mm
12mm
22 * 22
BVC 24/14
5mm
14mm
24 * 24
BVC 25/15
5mm
15mm
25 * 25
BVC 28/18
5mm
18mm
28 * 28
BVC 30/20
5mm
20mm
30 * 30
BVC 32/22
5mm
22mm
32 * 32
BVC 36/26
5mm
26mm
36 * 36
BVC 38/28
5mm
28mm
38 * 38
BVC 42/32
5mm
32mm
42 * 42
BVC 45/35
5mm
35mm
45 * 45
BVC 52/42
5mm
42mm
52 * 52
BVC 55/45
5mm
45mm
55 * 55
BVC 60/50
5mm
50mm
60 * 60
13mm
BVC 73/63
5mm
63m
73 * 73
16mm
BVC 85/75
5mm
75mm
85 * 85
20mm
BVC 105/85
10mm
85mm
105 * 105
22mm
BVC 140/120
10mm
120mm
140 * 140
Chain can be protected from damage

whilst lifting sharp edged loads with
UNITEX PU protective sleeves.
UNITEX PU protective sleeves are
made out of Polyurethane Elastomer,
a material unique in its resistance to
abrasion and cutting, thus offering
optimal protection of the chain. High
levels of grip on flat surfaces also
prevent load slippage. A textile lining
ensures that the inserted chain can
glide easily through the sleeve.
for chian
6mm
8mm
10mm
Material:
Polyurethane Elastomer approx. 80
Shore A, 450% stretch capacity (DIN
53 504), further stretch capacity 20
N/mm (DIN 53 515), Abrasion 60mg
(DIN 53 516).
PU corner protectionKSL
Type
Inside diameter D
Length L
Weigth per pcs.
KWS 25
KWS 40
30mm
80mm
0,3 kgs
50mm
125mm
1,0 kgs
corner protection KWS

Type
dimensions
D
KSL.2.190.120.OR
190
19
1200
0,5
KSL.2.190.600.OR
190
19
6000
0,55
Technical Specifications:
width: 190 x 190
Material: Polypropylene
70
Weight
(kg/m)
thickness: 19mm
Max. Length : 6 meter
Protection Sleeve
PVC Protection sleeve BLUE
Diameter
in mm
Width
in mm
BS50BL
38
60
BS60BL
50
BS75BL
63
BS100BL
76
120
10 t
10 t
BS150BL
100
160
120-150mm
12 - 30 t
12 - 20 t
BS180BL
127
200
180mm
35 - 50 t
25 - 30 t
BS200BL
150
235
200mm
55 - 60 t
35 -45 t
BS300BL
200
315
240-300mm
65 -100 t
50 - 70 t
Type
for web slings
for round slings single leg (1)
30-50mm
1-4 t
80
60mm
5-8 t
100
75-100mm
for round slings both legs (2)

1- 3 t
4 -5 t
5-8t
PU impregnated Protection sleeve red
Type
Diameter
in mm
Width
in mm
for web slings
for round slings single leg (1)
for round slings both legs (2)
BS50RE
38
60
30-50mm
1-4 t
1- 3 t
BS60RE
52
82
60-75mm
5-8 t
4 -5 t
BS75RE
75
118
75-100mm
10 t
5 - 10 t
BS150RE
102
160
120-150mm
12 - 30 t
12 - 20 t
BS180RE
125
196
180mm
35 - 50 t
25 - 30 t
BS200RE
152
239
200mm
55 - 60 t
35 - 45 t
1:
2:
71
UNITEX Heigth Safety contents
72
Company
Page
73
Full Body Harnesses
Page
74 - 75
Safety Lanyards
Page
76- 77
Height Safety Kits
Page
78
Fall Arrest Devices
Page
79 - 80
Karabiners & Connectors
Page
81 - 82
Belts and Work Positioning
Page
83
Confined Access, Rescue and Evacuation Equipment
Page
84
Storage Solutions and Miscellaneous
Page
85
UNITEX Heigth Safety the company
The Company
Unitex manufacturing group has for over 70 years been at the forefront of technological developments
in the design and production of innovative safety webbings from automotive seat belt to the one-piece
woven airbag.
The Equipment
Using the latest Computer Aided Design techniques coupled with the development of prototypes
through the use of rapid prototyping methods, Unitex is able to combine new designs with tried and
tested components benefiting the end user with improved functionality and the knowledge that
Unitexs products give absolute security.
The Approach
Height safety has diverse and evolving needs and its because of this and the increasing pressures
legislation is placing on the industry that Unitex boasts some of the most experienced safety
professionals.
Unitex is one of only a few companies offering a complete solution approach to its customers, with
tailored systems designed to meet individual customer needs.
73
Full Body Harnesses
Harnesses are the foundation of all fall protection systems, and its because of
this that Unitex, have developed a dynamic and functional range of harnesses
which allow unparalleled performance and comfort.
Unitex offers its range of harnesses with water repellent webbing and
rip stitch indicators as standard. Every harness is fully adjustable allowing
quick and easy adjustment using fittings made from a high tensile alloy.
74
RGH1
RGH4
EN361
EN361 and EN358
45mm water repellent webbing

Rear attachment point Rip
stitch indicators Fittings made
from high tensile steel alloy
1.05kg

Front, rear,side attachment Rip
Gear loops 1.90kg
RGH2
RGH5
EN361
EN361 and EN1497

Front and rear attachment Rip
1.20kg

Rear and front attachment points
Rip stitch indicators Fittings
made from high tensile steel alloy
Rescue strap 1.25kg
RGH3
RGH9
EN361 and EN358
EN361

Rear and side attachment Rip
from high tensile steel alloy Gear
loops 1.70kg
45mm elasticated leg straps water repellent webbing Rear

and front attachment points Rip
1.30kg
Full Body Harnesses

RGH11
RGH12
EN358 and EN361
EN361
Multi-functional harness Front

and rear attachment
Work positioning D rings
Rip stitch indicators
Water repellent webbing
Four sizes available
Weight 2.05kg
Quick connect harness

Front and rear attachment
Water repellent webbing
Sit support strap
Weight 1.60kg
RGH16
RGH18
EN358,361 and 813
EN361
Multi-task comfort harness

Ventral front D sit suspension
Rear and side attachment
Gear loops
Quick connect buckles
Weight 2.05kg
Fully elasticated harness

Rear attachment
Weight 1.20kg
RGH31
RGH32
RGHE
EN361
EN361
EN361
Economy harness
Rear attachment
Water repellent
Weight 0.90kg
Economy harness
Rear and front attachment
Water repellent
Weight 0.90kg
Economy harness
Rear attachment
Water repellent
Weight 0.75kg
RGK43
Comfort pad fits most harnesses
RGK31
Comfort leg pad fits most

harnesses
RGK56
Parking loop allows safe stowage of lanyard
75
Safety Lanyards
RGL9
Connecting your harness to the anchor point
EN354 and EN355
Its this crucial link that is often compromised by operators who routinely work
in difficult areas, subjecting the lanyard to a variety of abrasive surfaces which
may have a detrimental effect.
Unitexs response is to offer a complete range of lanyards including webbing,
rope and chain to ensure maximum choice, flexibility and most important of
all, safety.
lasticated construction
Length 1.3m and 1.8m
Shock absorber pack
Weight 1.20kg
RGL1
RGL4
EN354 and EN355
EN354
44kN polyester webbing Length

1.3m and 1.8m Shock absorber
pack Maximum arrest force <6kN
450mm extension strop
RGL5
EN354
RGL2
EN354 and EN355
12mm Kernmantel rope Length
1.3m and 1.8m Shock absorber
pack Maximum arrest force <6kN
Restraint lanyard different lengths available on request
RGL6
EN354 and EN355
RGL3
EN354 and EN355
Twin leg lanyard 44kN polyester
webbing Length 1.3m and 1.8m
Shock absorber pack Maximum
arrest force <6kN
lasticated construction
Length 1.3m and 1.8m
Shock absorber pack
Maximum arrest force <6kN
RGL7
EN355
Standard shock pack complete with delta links
76
Safety Lanyards
RGL11
RGL10
EN355
EN354 and EN355

Special mining fall arrest chain
lanyard Alloy steel to EN818-4
Length 1.8m
Fall arrest utility lanyard 12mm

kernmantel rope Length 1.7m
RGL12
RGL13
EN354
EN354 and EN355
Adjustable restraint lanyard

27mm 40kN polyester web
Steel adjuster Length 1-2m
djustable fall arrest lanyard

27mm 40kN polyester web
Steel ajuster Length 0.9-1.3m
and 1.2-1.8m
RGL14
EN354
Twin leg restraint
Lanyard 27mm 40kN
web Length on request
RGL16
RGL17
EN354/355
EN354
Adjustable twin leg fall

arrest lanyard 27mm
40kN web Length 0.91.3m and 1.2-1.8m
Twin leg rope restraint

lanyard Length on
request
RGL19
RGL20
EN354
EN354 and EN355
Adjustable twin leg restraint

Lanyard Length on request
Kinetic fall arrest lanyard

Length 1.3 and 1.8m
77
Height Safety Kits

Unitexs range of height safety kits are designed for multiple applications. Each complete kit consists of a full body harness,
a shock absorbing lanyard or restraint lanyard (or fall arrest system- RGHK3) and the connectors you need to ensure safe
working at height conditions at all time.
Every kit can be supplied either in a tough plastic container or a range of bags including pump bag or rucksack, making it
easy to keep all your height safety equipment close at hand and in one place!
RGHK1
Includes
2 point harness (RGH2) 1.8m
shock absorbing lanyard (RGL1)
with karabiner (RGK1)
RGHK2 and RGHK4

Includes
with scaffold hook (RGK11)
RGHK4 is supplied with the twin
leg lanyard version (RGL3)
RGHK3
Includes
with karabiner (RGK11) 2.5m
fall arrest block (RGA1) 1m
anchorage sling (RGK26)
RGHK5
Includes
Single point harness (RGH1)
and 2m restraint lanyard
(RGL12) RGHK5/IPAF 2 point
harness (RGH2) 1.5m adjustable
restraint lanyard (RGL12) with
karabiner (RGK1)
78
Fall Arrest Devices

When we designed our fall arrestors we had a number of key objectives.
Our benchmark goal was to design a state of the art fall arrestor which had increased functionality, was robust enough for all
environments and was a fail safe design.
The attention to detail of our design and test teams has produced a streamlined and ergonomic range of all arrest blocks.
Using the latest 3D computer modelling techniques, features such as the handle have been optimised for strength and use, even with
a gloved hand.
RGA1
RGA2 and 3
EN360
EN360
Retractable mini web block

Working length 2.5m
47mm polyester webbing
Built in shock pack
L100 x W110 x D75 (mm)
Max arrest force < 6kN
Weight 1.4kg
Multi purpose fall arrest

block
Working length 10m & 15m
5mm steel wire rope
Fall indicating connector
L325 x W200 x D80 (mm)
L340 x W228 x D80 (mm)
Weight 6.5kg and 10.5kg
RGA4
EN360 & EN1496 A & B
15m 3-way retrieval block
5mm steel wire rope
L340 x W258 x D80 (mm)
Weight 11.35kg
Xcalibre
RGA4B
The RGA4B bracket when
fitted to the RGR1 tripod
enables the RGA4 3 way
retrieval block to be safely
attached.
Material steel
Weight 1.4kg
RGA5
RGA26
EN360
EN360
Retractable mini web block

Working length 5.0m
28mm polyester webbing
Rip stitch indicator
L170 x W120 x D75 (mm)
Weight 2.0kg
Low weight fall arrest block

Working length 6.0m
5mm steel wire rope
L285 x W180 x D80 (mm)
Weight 5.2kg
Xcalibre is the latest generation Fall

Arrest Block from Unitex.
The Xcalibre3w offers the ultimate
answer in safety when working at low
levels due to its unique rapid braking
system (RBS).
Packed with unrivalled technology, super
light and finished with a sleek, compact
and contemporary design.
Ideal for working in the construction, off
shore, port safety and rigging industries.
Xcalibre
Join the revolution
79
Fall Arrest Devices
80
RGA7
RGA8
RGA9
EN360
EN360 & 341
EN360
Multi-purpose
fall arrest
block 33m
Multi-purpose fall
arrest block 33m
complete with
autodescent feature
3 way retrieval
rescue fall arrest
block 33m
RGA10R
RGA12R
RGA16E
EN352/2
EN352/2
EN353/2
16mm nylon rope

spliced at 1 end
available in 10, 20, 30m
11mm kernmantel rope

available in 10, 20, 30m
16mm nylon rope

supplied with splice
both ends
RGA10
RGA11
RGA12
EN353/2
EN353/2
EN353/2
Steel rope grab

for 16mm rope
8mm wire rope grab
11mm kernmantel
rope grab
RGA14
RGR/Tri-pulley
EN353/2
EN12278
Rocker rope grab to be used with

10.5-12.7mm kernmantel rope
Tri-pulley block to be used

with RGR1 tripod

These simple devices are often overlooked but should never be taken for granted. You will depend on them countless times during a normal
day, but how much thought do you really give them. Let Unitex offer you both the advice and choice you need.
Unitexs range of karabiners and connectors is unsurpassed and the most comprehensive available and this is for a reason. Different
applications and environments demand a specific solution and Unitex are there to bridge that technical gap.
RGK1
RGK2
EN362
EN362
Material - steel
Gate opening 19mm
Size 108mm x 58mm
Closure type screw gate
MBS 25kN
Weight 162g
Material - steel
Gate opening 17mm
Size 108mm x 58mm
Closure type twist lock
MBS 25kN
Weight 197g
RGK3
RGK4
EN362
EN362
Material - steel
Gate opening 22mm
Size 125mm x 90mm
MBS 40kN
Weight 276g
Material - aluminium
Gate opening 25mm
Size 125mm x 90mm
MBS 28kN
Weight 85g
RGK5
RGK6
EN362
EN362
Material - steel
Gate opening 55mm
Size 235mm x 130mm
MBS 35kN
Weight 751g
Gate opening 53mm
Size 235mm x 130mm
MBS 23kN
Weight 348g
RGK7 & RGK8
RGK9
EN362
EN362
Material stainless steel

Gate opening 105/140mm
Size 400/400mm x
175/200mm
Closure type self spring
MBS 22kN
Weight 300/400g
Material - alloy
Gate opening 22mm
Size 108mmx 58mm
Closure type screw gate
MBS 25kN
Weight 157g
81
82
RGK10
RGK11
RGK12
EN362
EN362
EN362
Material - steel
Gate opening 20mm
Size 155mm x 60mm
Closure type double
action
MBS 22kN
Weight 300g
Gate opening 60mm
Size 255mm x
112mm
Closure type double
action
MBS 22kN
Weight 473g
Material - steel
Gate opening 11mm
Size 70mm x 55mm
Closure type screw
MBS 22kN
Weight 86g
RGK13
RGK13P
RGK14
EN362
EN362
EN362
Material - steel
Gate opening 14mm
Size 105mm x 58mm
Closure type screw
gate
MBS 30kN
Weight 174g
Material steel
Gate opening 14mm
Size 105mm x 58mm
Closure type screw
gate
MBS 30kN
Weight 176g
Material - steel
Gate opening 24mm
Size 112mm x 65mm
Closure type triple
action
MBS 45kN
Weight 266g
RGK16
RGK17
EN362
EN362
Material - steel
Gate opening 18mm
Size 130mm x 70mm
Closure type twist
lock
MBS 40kN
Weight 300g
Material light alloy

Gate opening 18mm
Size 130mm x 60mm
Closure type double
action
MBS 25kN
Weight 150g
RGK27
EN795B
Material - steel
Gate opening N/A
Size 210mm x 60mm
Closure type plunger
MBS N/A
Weight 550g
Belts and Work Positioning

It is not always possible to carry out the tasks using work restraint. In these cases whether it be due to the nature of the work area or
the task actually being carried out, Unitex have developed the most comprehensive range of work positioning products, allowing the
operator total freedom of movement.
Depending on the actual application Unitex can offer both webbing belts and rope/wire products to suit your individual needs.
RGB1
RGB2
EN358
EN358
Twin D work work positioning restraint belt
Work positioning restraint belt

Alternative buckle and gear loops
RGBE-TA
RGBE
EN358
EN358
Work positioning belt with 2 attachment restraint

points and 2 gear loops
Work positioning restraint belt with rear

attachment point
RGB180-BT
RGP1
EN358
EN358

Work positioning belt

with 2 attachment restraint
RGP2
RGP3
EN358
EN358


RGP4
RGP11
EN358
EN358
Work positioning belt

with 2 attachment restraint

83
Confined Access, Rescue and

Evacuation Equipment
RGR1
RGR3
EN795
VRS RESCUE SYSTEM
Unique elliptical design

preventing twisting Height
range 1.68m-2.67m Span
diameter of 1.80m SWL 200kg
Alloy pulleys and 11mm

kermantel rope Safe for rescuer
SWL 136kg 1 person only
Weight 17.60k
Weight 18kg in combination

with 80m rope
RGR4
RGR8
Draft 95/501316
EN341
Escape and rescue system

Steel descender with 11mm
nylon kernmantel rope. 60mm
scaffold hook SWL 200kg 1 or
2 persons
9mm rope or combination For

persons up to 150kg Descent
rate 1.5m/second Proof tested
to 1,200kg Weight 2.95kg
Available up to 100m
Weight 0.55kg descender
RGR10
RGR11
EN341
Designed tubular webbing
Ultra compact and lightweight
Weight 1.00kg in combination
with 40m of webbing
weight 6.15kg
Available up to 80m
RGK42
RGR7
EN1496 A+B
Trauma suspension straps

fit to all harnesses
84
Quick and easy method

to ascend or descend to a
position of safety
50 metre tripod winch
RGR9
EN341
Descender unit
Storage Solutions and Miscellaneous

RGK22
RGK23
RGK24
Tool frog for

fitting to harness
Tool frog for

fitting to harness
Standard holdall for

safe storage
RGK24/C
RGK24/P
RGK24/R
Standard kit box
Pump bag
Ruck sack
RGK30
RGK32
Winch bag for

use with RGR7
Rope bag
RGK29
Tripod bag
RGK25/11
Rope protective
sleeve
RGH6
RGK25/16
Rescue triangle
ope protective sleeve
RGBT1
RGHL1
Beam trolley 75-200mm flange
Temporary horizontal lifeline

10m and 20m EN795 class C
RGK26
RGJ1
Girder sling standard length

1, 2 and 4m can be made
specific length EN795
Reflective jacket For all

Unitex harnesses
85
contents
Introduction
TS / STS
TSMP / STSMP
TSU / STSU
TSEU-A and TSU-R
TSHP and TSHPU
TNMK and TNMKA
FBK / TOBK
FHX / FHSX
TDH
THSK
FHX-V and TNMH
TPH
FSV / FSVW
TSCC
TBS
TBC and TBCA
TVK and TVKH
VERTICAL CLAMPS WITH AN EXTRA HARDENED PIVOT AND CAM
STELCON PLATEHOOKS and TRC
TTL / TBLC
SPARE PARTS
SPARE PARTS TS / STS
SPARE PARTS TSMP / STSMP
SPARE PARTS TSU /STSU
SPARE PARTS TSHP(U)
SPARE PARTS FH(S)X
SPARE PARTS FSV(W)
SPARE PARTS TPH
SPARE PARTS TBLC
SPARE PARTS HARDOX
SPARE PARTS SETS
Safely lifting vertical
Safely lifting horizontal
86
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
87 - 88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
introduction
Design
- Compact design and a low own weight.
- Use of top quality steel for housing, lifting shackle, cam and pivot guarantees a high level of usage and a long life.
Quality
- Very good quality and finish.
- Usage of Exotic steel for cam an pivot.
- Simple construction, therefor easy to repair.
- All lifting clamps are tested on our own testing facilities upto 2 times its Safe Working Load (SWL).
- Each clamp is supplied with a test certificate.
General
- Always read the manual before using a clamp.
- The lifting clamps are suitable for lifting and transporting of steel plates with a maximum hardness of 37 HrC
(345 HB, 1166 N/mm2).
- The lifting clamps are suitable for usage in normal atmospheric conditions, between -40C and +100C.
- Never overload a clamp and prevent the jerking of loads.
- When loading always use the whole jaw depth.
- Never lift more than one plate at the same time.
- Always keep your distance during lifting and descending of a load.
- Prevent situations that anybody is under the load.
- Any welding to the clamp is forbidden, this can influence the hardness and toughness of the clamp.
Delivery
- All lifting clamps are supplied with an original certificate.
- All lifting clamps are conform to European Standards according to Machine Directive 98/37/EC.
- All lifting clamps have been approved after stringent test by Government Safety Authorities (No. Al: 2753A).
87
Terrier introduction
Terrier Lifting Clamps provides a 5 year warranty on its lifting clamps. This warranty is applicable to the original end user of
the lifting clamps. Only if the clamp has been inspected, checked and maintained by this instructions and by an official dealer.
This warranty period of 5 years is valid from the day of purchase, and is liable to all conditions and measurements stated in
this document.
1. Conditions
This warranty only covers failures in the lifting tools which is the consequence of production errors which occur during normal
use. The warranty covers no wear to components such as pivots, cam assemblies, lock springs etc. Should there be any kind
of failure within this guarantee period, the lifting tool will be replaced or repaired to insight of the producer.
No warranty is given to clamps due to the following failures:
- Regular wear
- Overload
- Wrong and/or carelessly use
- Damages
- Not following procedures and measures
- Hoisting differing material other then indicated on clamp or stated in the user-manual
- Adapting and/or modifying of the Terrier clamp
- The injudicious use of the clamp, and not succeeding all indications which are stated in the users manual
- When maintenance and/or revision has not been carried out by an authorised Terrier distributor
The producer is not responsible for incidental damage or damage due to use of the lifting tools as well as from violation of this
guarantee manual.
2. Procedure Safety Inspection
All inspections and repairings must be written down in the maintenance diagram. This counts not only for your own
inspections but also for inspections which are carried out by your authorised Terrier distributor. When the clamp is handed in
for maintenance and inspection you always must provide the maintenance diagram.
Defective Lifting Clamps
When a form of wear or damage is indicated, you must take the following measures.
1 Take the lifting clamp out of use. (Note the date of failure of the lifting clamp)
2 Try to recover the cause of the failure, for example (complete list is available in chapter 1):
- Overload
- Wrong and/or carelessly use
- etc
These claims stated in no.2 do not fall under the guarantee! To guarantee the security of you and your colleagues you are
obliged to follow up this procedure.
3 Return your lifting clamp (with the maintenance history) to your authorised Terrier distributor.
4 If the lifting clamp has been revis
88
TS/STS
For vertical lifting and transporting of steel plates and structures.
The TS/STS lifting clamps are equipped with a safety mechanism, ensuring theclamp does not
slip when lifting force is applied and when load is being lowered.
The clamp is locked in closed as well as in open position.-Lifting capacity and jaw opening are
clearly engraved in the body.
Type STS are supplied with enlarged jaw opening.
Ref. nr.
Type
54A010075A
54A010100A
54A020100A
54A010150A
54A020200A
0.75 TS
54A020300A
54A010450A
54A020450A
54A010600A
54A010750A
54A020750A
54A010900A
54A011200A
54A011500A
54A011700A
54A012000A
54A012500A
54A013000A
54A030600A
54A030750A
54A030900A
54A031200A
54A031500A
54A032000A
54A032500A
54A033000A
Capacity(kg)
Jawopening
(R) (mm)
Dimensions in mm
S
Weight(kg)
2 TSE
750
1000
1000
1500
2000
0 - 13
0 - 18
0 - 25
0 - 20
0 - 35
47
55
55
80
80
30
45
45
65
65
205
265
265
335
335
100
125
142
165
185
35
38
38
55
55
37
47
47
56
56
10
15
15
17
17
3 TSE
3000
0 - 35
80
65
335
185
55
56
17
6,7
4.5 TS
4500
4500
6000
7500
7500
9000
12000
15000
17000
20000
25000
30000
0 - 25
0 -45
0 - 32
0 - 40
0 - 55
0 - 55
0 - 52
0 - 76
0 - 76
0 - 80
5 - 85
10 - 90
85
85
114
112
112
112
148
159
159
195
195
195
70
70
75
75
75
75
85
86
86
100
100
100
430
430
490
530
530
530
617
760
760
880
880
880
200
230
225
245
267
267
295
375
375
465
465
465
60
60
78
76
70
70
100
135
135
150
150
145
77
77
78
86
86
86
94
105
105
140
140
140
20
20
20
20
20
20
44
50
50
66
66
66
14,8
15,9
18,6
24
25
26
42
71
71
140
140
145
6000
7500
9000
12000
15000
20000
25000
30000
40 - 90
50-100
50-100
50-100
80-150
80-150
80-150
80-150
115
110
110
153
175
185
185
185
75
75
75
86
86
100
100
100
490
525
525
615
755
875
875
880
275
315
315
345
450
640
640
640
70
70
70
100
136
153
153
153
78
82
82
94
106
140
140
155
20
20
20
44
50
66
66
62,5
15
26
27
46
77
145
145
148
1 TS
1 TSE
1.5 TS
4.5 TSE
6 TS
7.5 TS
7.5 TSE
9 TS
12 TS
15 TS
17 TS
20 TS
25 TS
30 TS
6 STS
7.5 STS
9 STS
12 STS
15 STS
20 STS
25 STS
30 STS
1,5
3,3
3,6
6,3
6,5
89
TSMP/STSMP
The Terrier lifting clamps TS and STS are also available in MP-version.
MP-version means that the lifting shackle has a three way articulated linkage
arrangement.
For lifting and transporting of all steel plates and structures.
When attached to a fixed load bearing arm (e.g. spreader bar) the clamp will
retain its flexibility and no chain is needed.
Due to length of the three way linkage arrangement the clamp can be lowered
further between standing plates or structures.
Lifting capacity and jaw opening are clearly engraved in the body.
Type STSMP is supplied with an enlarged jaw opening.
90
Ref. nr.
Type
Capacity(kg)
54A040075A
54A040100A
54A050100A
54A040150A
54A050200A
54A050300A
54A040450A
54A050450A
54A040600A
54A040750A
54A050750A
54A040900A
54A041200A
54A041500A
54A041700A
54A042000A
54A042500A
0.75 TSMP
1 TSMP
1 TSEMP
1.5 TSMP
2 TSEMP
3 TSEMP
4.5 TSMP
4.5 TSEMP
6 TSMP
7.5 TSMP
7.5 TSEMP
9 TSMP
12 TSMP
15 TSMP
17 TSMP
20 TSMP
25 TSMP
750
1000
1000
1500
2000
3000
4500
4500
6000
7500
7500
9000
12000
15000
17000
20000
25000
54A060600A
54A060750A
54A060900A
54A061200A
54A061500A
54A062000A
54A062500A
6 STSMP
7.5 STSMP
9 STSMP
12 STSMP
15 STSMP
20 STSMP
25 STSMP
6000
7500
9000
12000
15000
20000
25000
Jawopening
(R) (mm)
Dimensions in mm
S
0 - 13
0 - 18
0 - 25
0 - 20
0 - 35
0 - 35
0 - 25
0 - 45
0 - 32
0 - 40
0 - 55
0 - 55
0 - 52
0 - 76
0 - 76
0 - 80
5 - 85
47
55
55
80
80
80
85
85
114
112
112
112
148
159
159
195
195
30
45
45
65
65
65
70
70
75
75
75
75
85
86
86
100
100
40 - 90
50-100
50-100
50-100
80-150
80-150
80-150
115
110
110
153
175
185
185
75
75
75
85
90
100
100
Weight(kg)
310
405
405
515
515
515
655
655
760
800
800
800
860
980
980
1200
1200
100
125
142
165
185
185
200
230
225
245
267
267
295
373
373
465
465
35
38
38
55
55
55
60
60
78
76
70
70
100
136
136
150
150
37
47
47
56
56
56
77
77
78
86
86
86
94
106
106
140
140
10
15
15
17
17
17
20
20
20
20
20
20
26
50
50
66
66
2
4,2
4,5
7,6
7,7
8
18,1
19,2
22,8
28
30
32
46
79
79
158
158
760
800
800
860
980
1200
1200
275
315
315
345
450
640
640
70
70
70
100
136
153
153
78
82
82
94
106
140
140
20
20
20
26
50
66
66
24
28
30
47
82
161
161
TSU/STSU
For lifting and transporting of steel plates and structures from all positions
(horizontal, vertical and sidelong).
Articulated lifting shackle.
The TSU /STSU lifting clamps are equipped with a safety mechanism, ensuring
the clamp does not slip when lifting force is applied and when load is being lowered.
The clamp is locked in closed as well as in open position.
Type STSU is supplied with enlarged jaw opening.
Ref. nr.
Type
Capacity(kg)
54A070075A
54A070100A
54A080100A
54A070150A
54A080200A
54A080300A
54A070450A
54A080450A
54A070600A
54A070750A
54A080750A
54A070900A
54A071200A
54A071500A
54A071700A
54A072000A
54A072500A
54A073000A
0.75 TSU
1 TSU
1 TSEU
1.5 TSU
2 TSEU
3 TSEU
4.5 TSU
4.5 TSEU
6 TSU
7.5 TSU
7.5 TSEU
9 TSU
12 TSU
15 TSU
17 TSU
20 TSU
25 TSU
30 TSU
750
1000
1000
1500
2000
3000
4500
4500
6000
7500
7500
9000
12000
15000
17000
20000
25000
30000
54A090600A
54A090750A
54A090900A
54A091200A
54A091500A
54A092000A
54A092500A
54A093000A
6 STSU
7.5 STSU
9 STSU
12 STSU
15 STSU
20 STSU
25 STSU
30 STSU
6000
7500
9000
12000
15000
20000
25000
30000
Jawopening
(R) (mm)
Dimensions in mm
Weight(kg)
0 - 13
0 - 18
0 - 25
0 - 20
0 - 35
0 - 35
0 - 25
0 - 45
0 - 32
0 - 40
0 - 55
0 - 55
0 - 52
0 - 76
0 - 76
0 - 80
0 - 85
0 - 90
47
55
55
80
80
80
85
85
114
112
112
112
148
159
159
195
195
195
30
50
50
70
70
70
70
70
78
78
78
78
85
85
85
100
100
100
203
295
295
370
370
370
430
430
527
565
565
565
650
765
765
900
900
900
100
125
142
165
185
185
200
230
225
245
267
267
295
373
373
465
465
465
35
38
38
55
55
55
60
60
78
76
70
70
100
136
136
150
150
145
37
47
47
56
56
56
77
77
78
86
86
86
94
106
106
140
140
140
10
14
14
16
16
16
20
20
32
32
32
45
48
48
48
71
71
71
1,7
3,5
3,9
7,2
7,3
7,5
15,6
16,7
21
26
30
32
45
75
77
145
148
150
40 - 90
50-100
50-100
50-100
80-150
80-150
80-150
80-150
115
110
110
153
175
185
185
185
75
75
75
86
86
100
100
100
527
565
565
650
765
900
900
900
275
315
315
345
450
640
640
640
70
70
70
100
136
153
153
153
78
82
82
94
106
140
140
155
20
20
20
44
50
66
66
62,5
32
28
28
45
80
150
150
155
91
TSEU-A and TSU-R

TSEU-A
Only 1 clamp needed for different kind of jobs.
Also the same clamp can be used if a big jaw opening is necessary.
For lifting and transporting of steel plates and structures from all positions.
Jaw opening from 0 - 95 mm. Adjustable by steps of 0-35 / 30-60 / 60-95 mm.
Capacity 3000 kg.
Strong and lightweight construction.
S
W
Ref. nr.
Type
54A100300A
3 TSEU-A
Capacity(kg)
3000
Dimensions in mm
Jawopening
(R) (mm)
0-95
80
70
385
235-300
55
42
15
Weight(kg)
11
TSU-R
For lifting and transporting of stainless steel plates and structures a TSU-R lifting
clamp is available.
Pivot and cam are made of stainless steel.
Body and lock lever are nickel plated to prevent corrosion due to carbon contamination.
Ref. nr.
Type
54A080200A
2 TSU-R
92
Capacity(kg)
2000
Jawopening
(R) (mm)
0 - 20
Dimensions in mm
S
80
70
365
165
55
45
18
Weight(kg)
7,2
TSHP and TSHPU

TSHP
For lifting and transporting of Holland-Profile (HP) and structures with HP-profile.
Also useful as a big-jaw opening clamp.
Standard with 3 pivots for extra powerful clamping force.
The Terrier TSHP lifting clamps are equipped with a safety mechanism, ensuring
the clamp does not slip when lifting force is applied and when load is being lowered.
Ref. nr.
Type
54A110100A
54A110150A
54A130150A
1.5 TSHP
1 TSHP
1.5 TSHP-A
Capacity(kg)
1000
1500
1500
3Dimensions in mm
Jawopening
(R) (mm)
0 - 80
0 - 80
0 - 155
205
205
205
65
65
65
530
530
530
272
272
272 - 340
55
55
55
52
52
52
16
16
16
Weight(kg)
19,5
20
22,5
TSHPU
TSHPU is a follow-up of the TSHP-1 and TSHP-1.5. It is especially designed for
lifting, handling and transporting of HP-profile and construction with HP-profile.
Properties
capacity 3.0 tons. Opening 0 - 35 mm.
capacity 5.0 tons. Opening 0 - 45 mm.
Ref. nr.
Type
54A120300A
54A120500A
3 TSHPU
5 TSHPU
Capacity(kg)
3000
5000
Jawopening
(R) (mm)
0 - 35
0 - 45
Dimensions in mm
S
90
110
70
68
385
425
185
245
55
84
42
67
15
25
Weight(kg)
15
19
93
TNMK / TNMKA
TNMK
TNMK is a NON-MARKING clamp with 2 special synthetic pads. The clamp can be used for
lifting, handling and transporting (stainless) steel, aluminium, wood and marble plates.
After lifting and handling, the clamps leave no markings.
TNMKA
A min. 3 mm/max. 180 mm
V min. 220 mm/max. 400 mm
Adjustable in steps of 20 mm.
H
S
A
V
Ref. nr.
54A140050A
54A150050A
54A160050A
54A140100A
54A140150A
54A140200A
54A140300A
94
Type
0.5 TNMK
0.5 STNMK
0.5 TNMKA
1 TNMK
1.5 TNMK
2 TNMK
3 TNMK
Capacity(kg)
500
500
500
1000
1500
2000
3000
Dimensions in mm
Jaw-opening
(A) (mm)
1 - 20
17 - 37
1 - 180
1 - 30
1 - 40
1 - 50
1 - 60
200
200
223
235
235
360
360
93
93
143
95
95
120
120
65
65
65
80
80
100
100
360
360
360
400
400
660
660
220
240
220-400
275
275
380
380
48
48
66
54
54
65
65
80
80
80
80
80
80
80
Weight(kg)
5,5
5,5
10
6,5
7,2
14
15
FBK and TOBK

For lifting and transportation of steel beams, profiles and structures where the
load must stay in position.
The special shape of the lifting shackle, places the centre of the gravity of the
beam to be lifted directly beneath the lifting shackle.
This maintains the equilibrium of the beam once it has been lifted and keeps the
flanges of the vertical so that the beam can easily be stacked or positioned.
Especially recommended for transportation and stacking of steelbeams (e.g. when
sawing of steelbeams, stacking of steelbeams and building of steel contructions).
Lifting capacity and jaw-opening are clearly engraved in the body.
For lifting and transportation of steel beams, profiles and structures.

Because of the safety mechanism, the clamp is locked in closed as well as in open position.
The clamp is suitable to lift steel beams on the flange as well as on the rear ends of the beam.
Other capacity and jaw-opening on request.
D
F
A
H
C
Ref. nr.
Type
54A170100A
54A170150A
54A170300A
54A180150A
1 FBK
1.5 FBK
3 FBK
2 TOBK
Capacity
(kg/pair)
1000
1500
3000
2000
Jaw-opening
(R) (mm)
0 - 15
0 - 20
0 - 25
3 - 20
Dimensions in mm
B
200
260
380
280
120
200
200
157
250
350
410
325
21,5
65
72
64
Weight
(kg/pc)
130
170
205
168
35
45
67
67
45
65
65
65
15
15
30
17
3
8
16
9,5
95
FHX / FHSX
For horizontal lifting and transporting of steel plates.
The compact shape and relative light own weight with a high lifting capacity.
The Terrier FHX/FHSX lifting clamps must always be used in pairs (or multiples thereof).
The FHS has an enlarged jaw opening.
Ref. nr.
Type
Capacity(kg)
54B010100A
54B010200A
54B010300A
54B010400A
54B010600A
54B010800A
54B010800A
54B011200A
1 FHX
2 FHX
3 FHX
4 FHX
6 FHX
8 FHX
10 FHX
12 FHX
1000
2000
3000
4000
6000
8000
10000
12000
54B020200A
54B020300A
54B020400A
54B020600A
54B020800A
54B021000A
54B021200A
54B021500A
2 FHSX
3 FHSX
4 FHSX
6 FHSX
8 FHSX
10 FHSX
12 FHSX
15 FHSX
2000
3000
4000
6000
8000
10000
12000
15000
96
Jawopening
(R) (mm)
Dimensions in mm
Weight(kg)
0 - 35
0 - 60
0 - 60
0 - 60
0 - 60
0 - 60
0 - 60
0 - 60
193
290
293
295
330
330
330
330
140
180
220
220
225
225
225
225
68
80
90
100
120
120
120
120
10
20
20
25
30
30
30
30
100
115
140
135
130
130
130
130
25
30,5
30,5
30,5
30,5
30,5
30,4
30,5
15
15
20
30
30
30
30
30
2,6
7,7
11,4
13
13
18
20
21
0 -100
0 -100
0 -100
0 -100
0 -100
0 -100
0 -100
0 -150
380
400
410
425
425
425
425
665
180
220
220
225
225
225
225
350
80
90
100
120
120
120
120
140
20
20
25
30
30
30
30
30
115
140
135
130
130
130
130
240
30,5
30,5
30,5
30,5
30,5
30,5
30,4
45
15
15
20
30
30
30
30
30
9
14
16
22
22
22
22
50
TDH
For lifting and transporting of thin sheets that deflect when being lifted.
Compact shape and relatively low own weights, with a high lifting capacity.
The Terrier TDH horizontal lifting clamps must always be used in pairs (or multiples thereof).
Ref. nr.
54.B.05.0100.A
54.B.05.0200.A
54.B.05.0400.A
54.B.05.0600.A
Type
1 TDH
2 TDH
4 TDH
6 TDH
Capacity
(kg/pair)
1000
2000
4000
6000
Jaw-opening
(R) (mm)
0 - 15
0 - 35
0 - 50
0 - 50
Dimensions in mm
A
167
235
310
310
85
135
157
157
10
20
35
35
22,5
26
40
40
100
115
130
130
140
180
235
235
65
80
130
130
Weight
(kg/pc)
3
8
20
20
97
THSK
For lifting, handling and transporting of packages and single steel plates
The Terrier THSK horizontal lifting clamps must always be used in pairs (or multiples thereof).
Capacity 1.5 tons per pair upto 9 tons per pair.
Opening 3 - 180 mm, 3 - 300 mm and 3 - 420 mm.
Ref. nr.
Type
54B060150A
54B060150B
54B060300A
54B060300B
54B060450A
54B060450B
54B060600A
54B060600B
54B060900A
54B060900B
1,5 THSK
1,5 THSK-W
3 THSK
3 THSK-W
4,5 THSK
4,5 THSK-W
6 THSK
6 THSK-W
9 THSK
9 THSK-W
98
Capacity
(kg/pair)
1500
1500
3000
3000
4500
4500
6000
6000
9000
9000
Dimensions in mm
Jawopening
(R) (mm)
Weight
(kg/pc)
3 - 180
3 - 300
3 - 180
3 - 300
3 - 180
3 - 420
3 - 180
3 - 420
3 - 180
3 - 420
290
410
300
410
300
530
305
540
305
540
200
200
240
235
240
235
250
250
250
250
15
15
20
20
20
20
25
25
25
25
135
135
165
165
165
170
160
165
160
165
27
27
27
27
27
27
27
27
27
27
60
60
70
70
70
70
77
75
77
75
87
87
105
105
105
105
120
120
120
120
20
20
20
20
20
20
20
20
20
20
9
11,5
14,5
13
13
15
20
23
25,5
29,5
FHX-V and TNMH

The FHX-V lifting clamp has a spring attached to the cam assembly. The spring
makes sure that the clamp will be closed on any desired spot.
One of the major advantages of this clamp is that only one person is able to place
the clamps and to guide the hoist.
These clamps are available with a capacity from 1000 kg per pair till 3000 kg per pair.
G
F
D
B
Ref. nr.
Type
Capacity
(kg/pair)
54.B.03.0100.A
54.B.03.0100.A
54.B.03.0300.A
54.B.03.0400.A
54.B.03.0600.A
1 FHX-V
2 FHX-V
3 FHX-V
4 FHX-V
6 FHX-V
1000
2000
3000
4000
6000
Dimensions in mm
Jaw-opening
(R) (mm)
0 - 35
0 - 60
0 - 60
0 - 60
0 - 60
Weight
(kg/pc)
193
290
293
310
310
140
180
180
220
220
85
125
125
165
165
10
15
20
30
30
100
115
115
140
140
25
30,5
30,5
30,5
30,5
15
16
16
20
20
3
9
10
15
15
The TNMH lifting clamp is suited for transporting and lifting objects with a fragile
surface. Like stainless steel, wood panels, aluminium etc.
The jaw and cam is covered with a high quality pressure resistant fabric.
These clamps are available with a capacity from 1000 kg per pair till 6000 kg per pair.
Ref. nr.
Type
54B040100A
54B040200A
54B040300A
54B040400A
54B040600A
1 TNMH
2 TNMH
3 TNMH
4 TNMH
6 TNMH
D
B
Capacity
(kg/pair)
1000
2000
3000
4000
6000
Jaw-opening
(R) (mm)
0 - 25
0 - 45
0 - 45
0 - 50
0 - 50
Dimensions in mm
A
Weight
(kg/pc)
154
270
275
305
310
140
225
225
250
250
65
90
90
105
120
15
23
28
28
33
95
150
160
160
160
20
30,5
30,5
30,5
30,5
15
15
15
20
20
3
8
16
9,5
17
99
TPH
For horizontal lifting and transporting of steel and concrete pipes.
Compact shape and relatively low own weight with a high lifting capacity.
The surface is equipped with special plastic.
The Terrier TPH will be delivered per pair.
Plastic cover is easy to change.
TPH can be delivered with Berglock-coupling BL.
Dimensions in mm
Ref. nr.
Type
Capacity
(kg/pair)
Jawopening
(R) (mm)
Weight
(kg/pc)
54B070150A
54B070300A
54B070400A
54B070600A
54B070800A
54B071000A
54B071200A
54B071500A
54B072000A
1.5 TPH
3 TPH
4 TPH
6 TPH
8 TPH
10 TPH
12 TPH
15 TPH
20 TPH
1500
3000
4000
6000
8000
10000
12000
15000
20000
40
40
50
50
70
70
70
70
70
120
120
120
120
120
120
120
120
120
32
32
32
32
32
32
32
32
32
175
175
195
195
195
215
215
215
215
70
70
70
70
70
70
70
70
70
25
25
25
25
25
45
45
60
60
15
15
25
25
26
26
26
26
26
1,6
1,6
2
3,3
3,6
5
6
10
16
100
FSV / FSVW
For horizontal lifting and transporting of steel beams and structures.
Can also be attached upside down and be used as a (temporary) lifting point.
Has equal opening and closing of both jaws for simple and quick assembly.
Type FSVW is identical to type FSV but is delivered without a lifting eye so you
can choose your own means of fixation.
Ref. nr.
Type
Capacity
(kg/pcs)
54C010100A
54C010200A
54C010300A
54C010400A
54C010500A
54C011000A
1 FSV
2 FSV
3 FSV
4 FSV
5 FSV
10 FSV
1000
2000
3000
4000
5000
10000
Ref. nr.
Type
Capacity
(kg/pcs)
54C020100A
54C020200A
54C020300A
54C020400A
54C020500A
1 FSVW
2 FSVW
3 FSVW
4 FSVW
5 FSVW
1000
2000
3000
4000
5000
Jaw-opening
(R) (mm)
75 - 190
75 - 190
75 - 190
150 - 300
150 - 300
350 - 450
Dimensions in mm
B
C-max
D-Max
30
30
30
50
50
130
285
285
285
460
460
670
310
310
310
430
430
670
73
73
73
79
79
85
120
120
120
180
180
200
Dimensions in mm
Jaw-opening
(R) (mm)
C-max
D-Max
75 - 190
75 - 190
75 - 190
150 - 300
150 - 300
30
30
30
30
30
285
285
285
460
460
150
150
150
245
245
73
73
73
79
79
120
120
120
180
180
Weight(kg)
4
5
5
13
14
35
Weight(kg)
3
4
4
12
12
101
TSCC
Universal screw clamp for vertical and horizontal lifting and transporting of a
large variety of steel structures.
The TSCC screw clamp is fitted with a moveable cam on the thread spindle which
provides a powerful clamping force on the workpiece.
The articulated lifting eye ensures an effective clamping force in every position.
Ref. nr.
Type
54.C.03.005.0A
54.C.03.0075.A
54.C.03.0100.A
54.C.03.0150.A
54.C.03.0300.A
54.C.03.0600.A
54.C.03.0100.B
54.C.03.0300.B
0.5 TSCC
0.75 TSCC*
1 TSCC
1.5 TSCC
3 TSCC
6 TSCC
1 TSCC-W
3 TSCC-W
*is runniing out
102
Capacity(kg)
500
750
1000
1500
3000
6000
1000
3000
Dimensions in mm
Jawopening
(R) (mm)
0 - 28
0 - 22
0 - 30
0 - 32
0 - 50
0 - 75
50 - 100
25 - 75
156
167
175
187
224
291
258
250
113
201
204
229
265
365
273
291
89
120
126
135
165
215
155
165
26
42
42
42
49
63
42
49
76
125
128
143
165
214
190
191
30
46
46
46
54
69
46
54
17
38
38
45
50
80
45
50
Weight(kg)
0,8
3
3,2
4
7
18
3,2
7,8
TBS
For use as a temporary lifting point in any room where HP-profile is being used,
such as sectional ship parts and ship engine rooms.
The clamp is used for HP-100 to HP-240.
Ref. nr.
Type
54C040150A
54C040300A
1.5 TBS
3 TBS
Capacity(kg)
1500
3000
Dimensions in mm
Jaw-opening
(R) (mm)
HP100 - 240
HP100 - 240
170
200
70
70
149
149
16
16
44
44
70
70
40
80
Weight(kg)
3
6,5
103
TBC and TBCA

TBC
For vertical lifting and transporting of concrete pipe and wells.
The TBC clamps must always be used in pairs or per three clamps.
Higher capacities or other jaw opening upon request.
The moveable side is fitted with a special high pressure plastic surface.
TBCA
R min. 60 mm/max. 220 mm.
Adjustable in steps of 25 mm.
104
Ref. nr.
Type
54E020050A
54E020050A
54E030100A
54E040100A
0.5 TBC
1 TBC
1 TBCT
1 TBC-A
Capacity(kg)
500
1000
1000
1000
Dimensions in mm
Jaw-opening
(R) (mm)
Weight
(kg/pc)
60-120
60-120
60-120
50-230
170
170
235
170
110
110
60
110
160
160
75
160
12
12
16
12
12
12
12
12
25
25
35
25
60
60
35
60
10
10
8,5
11
TVK and TVKH

TVK
For safe lifting and transporting of steel (oil) drums.
With automatic locking mechanism.
The TVK steel drum clamps are supplied with an original certificate.
The TVK steel drum clamps can be used singleary or per pair as well.
Ref. nr.
Type
54D010050A
TVK
Capacity(kg)
Dimensions in mm
Jawopening
(R) (mm)
500
0 - 17
129
12
96
15
28
Weight(kg)
1,6
TVKH
For lifting, handling and transporting of (oil)drums, where the drums have to stay
in a horizontal position.
Capacity 0.6 tons.
Ref. nr.
Type
Capacity(kg)
54D020060A
TVKH
600
Dimensions in mm
A
300
375
290
80
50
12
Weight(kg)
105
VERTICAL CLAMPS WITH AN EXTRA

HARDENED PIVOT AND CAM
Equiped with an extra hardened pivot and cam for lifting and transporting steel
plates with a hardnes of max. 50 HRC. (for Hardox 400 and 500)
Can be delivered as TS, TSMP and TSU model.
Please ask for special specifications.
For dimensions and loading diagrams see page 5, page 6 and page 7.
Other capacity and jaw-opening on request.
Ref. nr.
106
Type
Capacity(kg)
Jaw-opening
(R) (mm)
Dimensions in mm
S
Weight(kg)
54A010075H
54A020100H
54A020100H
54A020300H
54A020450H
54A010600H
54A020750H
0.75 TS-H
1 TSE-H
2 TSE-H
3 TSE-H
4.5 TSE-H
6 TS-H
7.5 TSE-H
750
1000
2000
3000
4500
6000
75000
0 - 13
0 - 25
0 - 35
0 - 35
0 - 45
0 - 32
0 - 55
47
55
78
78
85
114
112
30
44
65
65
68
75
75
205
240
350
350
430
490
540
100
142
185
185
245
255
245
37
35
43
54
67
69
70
37
35
46
54
67
69
70
10
15
17
17
22
25
25
1,3
3,6
6,5
6,7
15,9
18,6
24
54A040075H
54A050100H
54A050200H
54A050300H
54A050450H
54A040600H
54A050750H
0.75 TSMP-H
1 TSEMP-H
2 TSMP-H
3 TSEMP-H
4.5 TSEMP-H
6 TSMP-H
7.5 TSEMP-H
750
1000
2000
3000
4500
6000
7500
0 - 13
0 - 25
0 - 35
0 - 35
0 - 45
0 - 32
0 - 55
47
55
80
80
85
114
112
30
45
65
65
68
74
75
260
425
510
515
705
760
820
100
142
180
185
245
240
245
25
38
58
55
64
71
58
37
35
43
42
67
69
70
10
15
17
15
22
25
25
2
4,5
7,7
5
19,2
22,8
28
54A070075H
54A080100H
54A080200H
54A080300H
54A080450H
54A070600H
54A080750H
0.75 TSU-H
1 TSEU-H
2 TSEU-H
3 TSEU-H
4.5 TSEU-H
6 TSU-H
7.5 TSEU-H
750
1000
2000
3000
4500
6000
7500
0 - 13
0 - 25
0 - 35
0 - 35
0 - 45
0 - 32
0 - 55
47
55
80
80
85
115
112
30
48
70
70
68
80
80
210
285
380
385
425
520
560
100
142
180
185
245
245
245
25
38
58
55
64
64
58
37
35
43
42
67
69
70
10
18
18
15
25
32
32
1,7
3,9
7,3
7,5
16,7
21
26
STELCON PLATEHOOKS and TRC

STELCON PLATEHOOKS
For vertical transport of rail profiles.

The TRC is equiped with a safety mechanism, ensuring the clamp does not slip
when lifting force is applied and when load is being lowered.
The clamp is locked in closed as well in open position.
Other capacities or other profile dimensions on request.
Dimensions in mm
Ref. nr.
Type
Capacity(kg)
Jawopening
(R) (mm)
54E050150A
TRC
1500
40 - 75
63
65
390
170
70
48
16
Weight(kg)
107
TTL / TBLC
TTL
For vertical lifting of tubes, bundles of tubes and solid round material.
Ref. nr.
Type
54E060050A
54E060100A
54E060200A
54E060300A
0.5 TTL
1 TTL
2 TTL
3 TTL
Capacity(kg)
500
1000
2000
3000
Jaw-opening
(R) (mm)
48,3 - 114,3
114,3 - 219,1
219,1 - 368
368 - 508
Dimensions in mm
B max
215
345
610
720
47
51
60
60
42
42
65
65
Weight(kg)
5
9
31
40
TBLC
For vertical lifting and transporting without marking of products with parallel
sides in various materials as steel, wood, plastic, concrete, marble etc.
The clamp is locked in the open position. To perform lifting, the operator must
activate the handle and hold it up while the force on the lifting eye is going
upwards. When laying down the load, the clamp automaticly locksitself open.
De pads are covered with special plastic to avoid dammaging of the load.
D
F
R
B
Ref. nr.
54.E.07.0050.A
54.E.07.0100.A
54.E.07.0200.A
54.E.07.0300.A
108
Type
0,5 TBLC
1 TBLC
2 TBLC
3 TLC
Capacity(kg)
Jaw-opening
(A) (mm)
500
1000
2000
3000
30-110
100-230
220-360
350-500
Dimensions in mm
B min-max
C min-max
E min-max
275-325
440-530
600-675
740-840
270-420
360-610
400-680
490-840
45
45
45
65
100
140
170
200
70*80
100*120
100*120
100*120
15
17
17
20
Weight(kg)
7
12
18
32
SPARE PARTS
All spare parts are available either separately or as repair sets. It is recommended
when any parts are damaged to replace them straight away and not to take any risk.
When ordering spare parts always give: model, lifting capacity, jaw opening and
serial number as well as the needed spare parts.
A Cam assembly
B Lock lever assembly
C Lock spring
D Cam pin
E Pivot complete
F Shackle pin
G Lifting eye for TS, STS, MP model
H Lifting eye for TSU, STEU model
I Linkage arr. STMP, STSMP model
J Link pin for MP model
L Cam for FHX model
M Cam pin for FHX model
N Cam for FHSX model
O Cam pin for FHSX model
For every vertical clamps are
revision- sets and repairsets available.
The repair sets contain :
A Cam assembly
C Lock spring
D Cam pin
E Pivot set
The revision sets contain :
A Cam assembly
B Lock lever assembly
C Lock spring
D Cam pin
E Pivot complete
109
Spareparts - TS / STS
All spare parts are available either separately or as repair sets. It is recommended when any parts are damaged to replace them straight away and not
to take any risk.
When ordering spare parts always give: model, lifting capacity, jaw opening
and serial number as well as the needed spare parts
Type
110
Cam assy
Lock leverassy
Spring
Campin
Pivot
Shackle pin
Lifting shackle
0.75 TS
55.550020
55.550031
55.250000
55.550029
55.550019
55.550058
55.550050
1 TS
55.550820
55.550831
55.250800
55.550829
55.550819
55.550858
55.550850
1 TSE
55.550880
55.550831
55.250800
55.550829
55.550819
55.550858
55.550850
1.5 TS
55.550120
55.550131
55.250100
55.550129
55.550119
55.550158
55.550150
2 TSE
55.550920
55.550131
55.250100
55.550129
55.550119
55.550158
55.550150
3 TSE
55.550920
55.550131
55.250100
55.552929
55.550119
55.550158
55.550150
4.5 TS
55.550220
55.550231
55.250200
55.550329
55.550219
55.550258
55.550250
4.5 TSE
55.552220
55.552431
55.250200
55.550329
55.550219
55.550258
55.550250
6 TS
55.550320
55.550331
55.250300
55.550329
55.550219
55.550358
55.550350
7.5 TS
55.550420
55.550431
55.250400
55.550429
55.550219
55.550458
55.550450
7.5 TSE
55.552620
55.550431
55.250400
55.550429
55.550219
55.550458
55.550450
9 TS
55.552620
55.550531
55.250400
55.551029
55.550219
55.550458
55.550450
12 TS
55.550520
55.550531
55.250400
55.550529
55.550219
55.550558
55.550550
15 TS
55.550620
55.550631
55.250600
55.550629
55.550619
55.550658
55.550650
17 TS
55.550620
55.550631
55.250600
55.550629
55.550619
55.550658
55.550650
20 TS
55.550720
55.550731
55.250700
55.550729
55.550719
55.550758
55.550750
25 TS
55.550720
55.550731
55.250700
55.550729
55.550719
55.550758
55.550750
30 TS
55.550720
55.550731
55.250700
55.550929
55.550719
55.550758
55.550750
Spareparts - TSMP / STSMP
Type
Cam assy
Lock leverassy
Spring
Campin
Pivot
Shackle pin
Lifting shackle
Link arr.
Link pin
0.75 TSMP
55.250000
55.550029
55.550019
55.550058
55.550050
55.550060
55.550059
55.550060
55.550059
1 TSMP
55.250800
55.550829
55.550819
55.550858
55.550850
55.550860
55.570128
55.550860
55.570128
1 TSEMP
55.250800
55.550829
55.550819
55.550858
55.550850
55.550860
55.570128
55.550860
55.570128
1.5 TSMP
55.250100
55.550129
55.550119
55.550158
55.550150
55.550160
55.550129
55.550160
55.550158
2 TSEMP
55.250100
55.550129
55.550119
55.550158
55.550150
55.550160
55.550129
55.550160
55.550158
3 TSEMP
55.250100
55.552929
55.550119
55.550158
55.550150
55.550160
55.550129
55.550160
55.550158
4.5 TSMP
55.250200
55.550329
55.550219
55.550258
55.550250
55.550260
55.550259
55.550260
55.550259
4.5 TSEMP
55.250200
55.550329
55.550219
55.550258
55.550250
55.550260
55.550259
55.550260
55.550259
6 TSMP
55.250300
55.550329
55.550219
55.550358
55.550350
55.550360
55.550329
55.550360
55.550329
7.5 TSMP
55.250400
55.550429
55.550219
55.550458
55.550450
55.550460
55.550329
55.550460
55.550329
7.5 TSEMP
55.250400
55.550429
55.550219
55.550458
55.550450
55.550460
55.550329
55.550460
55.550329
9 TSMP
55.250400
55.551029
55.550219
55.550458
55.550450
55.550460
55.550329
55.550460
55.550329
12 TSMP
55.250400
55.550529
55.550219
55.550558
55.550551
55.550560
55.550559
55.550560
55.550559
15 TSMP
55.250600
55.550629
55.550619
55.550658
55.550651
55.550660
55.550659
55.550660
55.550659
17 TSMP
55.250600
55.550629
55.550619
55.550658
55.550651
55.550660
55.550659
55.550660
55.550659
20 TSMP
55.250700
55.550729
55.550719
55.550758
55.550751
55.550760
55.550759
55.550760
55.550759
25 TSMP
55.250700
55.550729
55.550719
55.550758
55.550751
55.550760
55.550759
55.550760
55.550759
111
Spareparts - TSU / STSU
All spare parts are available either separately or as repair sets. It is

recommended when any parts are damaged to replace them straight
away and not to take any risk.
When ordering spare parts always give: model, lifting capacity, jaw
opening and serial number as well as the needed spare parts
112
Type
Cam assy
Lock leverassy
Spring
0.75 TSU
55.550020
55.550031
55.250000
1 TSU
55.550820
55.550831
55.250800
1 TSEU
55.550880
55.550831
1.5 TSU
55.550120
2 TSEU
55.550920
Campin
Pivot
Shackle pin
Lifting shackle
55.550029
55.550019
55.550058
55.555050
55.550829
55.550819
55.550858
55.555850
55.250800
55.550829
55.550819
55.550858
55.555850
55.550131
55.250100
55.550129
55.550119
55.550158
55.555150
55.550131
55.250100
55.550129
55.550119
55.550158
55.555150
3 TSEU
55.550920
55.550131
55.250100
55.552929
55.550119
55.550158
55.555150
4.5 TSU
55.550220
55.550231
55.250200
55.550329
55.550219
55.550258
55.555250
4.5 TSEU
55.552220
55.552431
55.250200
55.550329
55.550219
55.550258
55.555250
6 TSU
55.550320
55.550331
55.250300
55.550329
55.550219
55.550358
55.555350
7.5 TSU
55.550420
55.550431
55.250400
55.550429
55.550219
55.550458
55.555450
7.5 TSEU
55.552620
55.550431
55.250400
55.550429
55.550219
55.550458
55.555450
9 TSU
55.552620
55.550531
55.250400
55.551029
55.550219
55.550458
55.555450
12 TSU
55.550520
55.550531
55.250400
55.550529
55.550219
55.550558
55.555550
15 TSU
55.550620
55.550631
55.250600
55.550629
55.550619
55.550658
55.555650
17 TSU
55.550620
55.550631
55.250600
55.550629
55.550619
55.550658
55.555650
20 TSU
55.550720
55.550731
55.250700
55.550729
55.550719
55.550758
55.555750
25 TSU
55.550720
55.550731
55.250700
55.550729
55.550719
55.550758
55.555750
30 TSU
55.550720
55.550731
55.250700
55.550929
55.550719
55.550758
55.555950
2 TSU-R
55.562120
55.562131
55.250100
55.562129
55.562119
55.550158
55.555150
3 TSEU-A
55.550920
55.550131
55.250100
55.552929
55.550119
55.550158
55.555150
Spareparts - TSHP(U)
When ordering spare parts always give: model, lifting capacity, jaw opening and serial
number as well as the needed spare parts.
Type
G/H
Cam assy
Lock leverassy
Spring
Campin
Pivot
Shackle pin
Lifting shackle
1 TSHP
55.560120
55.560131
55.260100
55.555129
55.550119
55.550158
55.560150
1.5 TSHP
55.560120
55.560131
55.260100
55.555129
55.550119
55.550158
55.560150
3 TSHPU
55.550920
55.550131
55.250100
55.555129
55.550119
55.550158
55.555150
5 TSHPU
55.552220
55.552431
55.250200
55.550329
55.550219
55.550258
55.555250
Spareparts - TNMK
Type
Upper -
Under -
Push plate
Lock leverassy
Spring
Campin
Push plate
Shackle pin
Lifting shackle
0.5 TNMK
55.562013
55.550831
55.250800
55.555129
55.562014
55.262351
55.262350
1 TNMK
55.562013
55.562433
55.250100
55.552929
55.562014
55.262351
55.262350
1.5 TNMK
55.562013
55.562433
55.250100
55.552929
55.562014
55.262351
55.262350
2 TNMK
55.562013
55.562633
55.250200
55.562618
55.562014
55.290160
55.290159
3 TNMK
55.562013
55.562633
55.250200
55.562618
55.562014
55.290160
55.290159
Spareparts - FBK
Type
Cam assy
Lock leverassy
Spring
Campin
Pivot
Shackle pin
Lifting shackle
1 FBK
55.550820
55.550831
55.250800
55.550829
55.550819
55.551008
55.551015
1.5 FBK
55.550120
55.555131
55.250100
55.555129
55.550119
55.551058
55.551050
3 FBK
55.550220
55.550231
55.250200
55.550329
55.550219
55.551158
55.551150
113
Spareparts - FH(S)X
All spare parts are available either separately or as repair sets. It is recommended when
any parts are damaged to replace them straight away and not to take any risk.
number as well as the needed spare parts
Type
Type
Cam
Cam pin
1 FHX
55.5621123
2 FHX
3 FHX
Cam
Cam pin
55.561129
2 FHSX
55.561523
55.553029
55.561023
55.553029
3 FHSX
55.561523
55.553029
55.561023
55.553029
4 FHSX
55.561723
55.553229
4 FHX
55.561223
55.553229
6 FHSX
55.561723
55.553229
6 FHX
55.561223
55.553229
8 FHSX
55.561823
55.553429
8 FHX
55.561423
55.553429
10 FHSX
55.561823
55.553429
10 FHX
55.561423
55.553429
12 FHSX
55.561823
55.553429
12 FHX
55.561423
55.223429
15 FHSX
55.520120
55.553629
Spareparts - THD
Type
Cam
Cam pin
1 TDH
570123
561129
2 TDH
570223
553029
Spareparts - THSK
Type
114
Connecting -
Cam
Cam pin
Adjustable pin
plate
1.5 THSK
55.530159
55.260358
55.260329
55.515160
3 THSK
55.530159
55.260358
55.260329
55.530160
4.5 THSK
55.530159
55.260358
55.260329
55.530160
6 THSK
55.530159
55.260358
55.260629
55.560160
9 THSK
55.530159
55.260358
55.260629
55.560160
Spareparts - FSV(W)
Type
Lifting eye
Shackle pin
Spindel compl.
1 FSV(W)
55.551550
55.551558
55.251530
2 FSV(W)
55.551550
55.551558
55.251530
3 FSV(W)
55.551650
55.551658
55.251530
4 FSV(W)
55.551750
55.551758
55.251730
5 FSV(W)
55.551850
55.551858
55.251730
10 FSV
55.551950
55.551958
55.251930
Spareparts - TBS
Type
Lifting eye
Shackle pin
Spindel compl.
1.5 TBS
55.550850
55.562429
55.562423
3 TBS
55.550150
55.562429
55.562423
Spareparts - TSCC
Cam
Spindel compl.
Pivot
0.5 TSCC
Type
55.562015
55.562017
55.562016
0.75 TSCC
55.562515
55.562517
55.562516
1.5 TSCC
55.562515
55.562517
55.562516
55.562315
55.562317
55.562316
55.562615
55.562617
55.562616
3 TSCC
6 TSCC
Lifting eye
55.562.350
115
spareparts - TPH
All spare parts are available either separately or as repair sets. It is recommended when any parts are damaged to replace them straight away and not
to take any risk.
When ordering spare parts always give: model, lifting capacity, jaw opening
and serial number as well as the needed spare parts.
Type
Total width
Plastic coverset
1.5 TPH
37 mm
55.560301
3 TPH
37 mm
55.560301
4 TPH
42 mm
55.560401
6 TPH
42 mm
55.560401
8 TPH
45 mm
55.560801
10 TPH
85 mm
55.560810
Total width
Plastic coverset
67 mm
55.560813old
12 TPH
85 mm
55.560810
67 mm
55.560813old
15 TPH
100 mm
55.560820
67 mm
55.560813old
20 TPH
100 mm
55.560820
67 mm
55.560813old
Spareparts - TBC
Type
Hinge pin (small)
Hinge pin (large)
Cam
0.5 TBC
55.570128
55.570129
55.570120
1 TBC
55.570128
55.570129
55.570120
Spareparts - TVK
116
Type
Hinge pin
Lifting eye
Ratchet
0.5 TVK
55.570128
55.528002
55.528001
spareparts - TBLC
Type
Lifting eye
Jaw blocks
0.25 TBLC
55.550050
55.501255
0.5 TBLC
55.550050
55.501255
1 TBLC
55.550850
55.501255
1.5 TBLC
55.550150
55.501105
2 TBLC
55.550850
55.501255
3 TBLC
55.550150
55.501105
Spareparts - TBC
Type
Lifting eye
0.5 TTL
55.550050
1 TTL
55.550850
2 TTL
55.550150
3 TTL
55.550150
117
Spareparts - Hardox
Type
Cam assy
Lock leverassy
Spring
0.75 TS-H
55.550020.5
55.550031
55.250000
1 TSE-H
55.550880.5
55.550831
55.250800
2 TSE-H
55.550920.5
55.550131
55.250100
Campin
Pivot
Shackle pin
Lifting shackle
55.550029
55.550019.5
55.550058
55.550050
55.550829
55.550819.5
55.550858
55.550850
55.550129
55.550119.5
55.550158
55.550150
3 TSE-H
55.550920.5
55.550131
55.250100
55.552929
55.550119.5
55.550158
55.550150
4.5 TSE-H
55.552220.5
55.552431
55.250200
55.550329
55.550219.5
55.550258
55.550250
6 TS-H
55.550320.5
55.550331
55.250300
55.550329
55.550219.5
55.550358
55.550350
7.5 TSE-H
55.552620.5
55.550431
55.250400
55.550429
55.550219.5
55.550458
55.550450
Type
Cam assy
Lock leverassy
Spring
Campin
Pivot
Shackle pin
Lifting shackle
0.75 TSU-H
55.550020.5
55.550031
55.250000
55.550029
55.550019.5
55.550058
55.555050
1 TSEU-H
55.550880.5
55.550831
55.250800
55.550829
55.550819.5
55.550858
55.555850
2 TSEU-H
55.550920.5
55.550131
55.250100
55.550129
55.550119.5
55.550158
55.555150
3 TSEU-H
55.550920.5
55.550131
55.250100
55.552929
55.550119.5
55.550158
55.555150
4.5 TSEU-H
55.552220.5
55.552431
55.250200
55.550329
55.550219.5
55.550258
55.555250
6 TSU-H
55.550320.5
55.550331
55.250300
55.550329
55.550219.5
55.550358
55.555350
7.5 TSEU-H
55.552620.5
55.550431
55.250400
55.550429
55.550219.5
55.550458
55.555450
Type
Cam assy
Lock leverassy
Spring
Campin
Pivot
Shackle pin
Lifting shackle
Link arr.
Link pin
0.75 TSMP-H
55.550020.5
55.550031
55.250000
55.550029
55.550019.5
55.550058
55.550050
55.550060
55.550059
1 TSEMP-H
55.550880.5
55.550831
55.250800
55.550829
55.550819.5
55.550858
55.550850
55.550860
55.570128
2 TSEMP-H
55.550920.5
55.550131
55.250100
55.550129
55.550119.5
55.550158
55.550150
55.550160
55.550129
3 TSEMP-H
55.550920.5
55.550131
55.250100
55.552929
55.550119.5
55.550158
55.550150
55.550160
55.550129
4.5 TSEMP-H
55.552220.5
55.552431
55.250200
55.550329
55.550219.5
55.550258
55.550250
55.550260
55.550259
6 TSMP-H
55.550320.5
55.550331
55.250300
55.550329
55.550219.5
55.550358
55.550350
55.550360
55.550329
7.5 TSEMP-H
55.552620.5
55.550431
55.250400
55.550429
55.550219.5
55.550458
55.550450
55.550460
55.550329
118
Spareparts Sets
Repair Sets.
Capacity
Set nr.
Jaw opening
Cam assy
Spring
Cam pin
Pivot
0.75 T
55.RS650000
0 - 13 mm
55.550020
55.250000
55.550029
55.550019
1T
55.RS650801
0 - 18 mm
55.550820
55.250800
55.550829
55.550819
1 TSE
55.RS650811
0 - 25 mm
55.550880
55.250800
55.550829
55.550819
1.5 T
55.RS650101
0 - 20 mm
55.550120
55.250100
55.550129
55.550119
2T
55.RS650901
0 - 35 mm
55.550920
55.250100
55.550129
55.550119
3T
55.RS650911
0 - 35 mm
55.550920
55.250100
55.552929
55.550119
4.5 T
55.RS650201
0 - 25 mm
55.550220
55.250200
55.550329
55.550219
4.5 TSE
55.RS650221
0 - 45 mm
55.552220
55.250200
55.550329
55.550219
6T
55.RS650301
0 - 32 mm
55.550320
55.250300
55.550329
55.550219
7.5 T
55.RS650401
0 - 40 mm
55.550420
55.250400
55.550429
55.550219
7.5 TSE
55.RS650611
0 - 55 mm
55.552620
55.250400
55.550429
55.550219
9T
55.RS650612
0 - 55 mm
55.552620
55.250400
55.555529
55.550219
12 T
55.RS650501
0 - 52 mm
55.550520
55.250500
55.550529
55.550219
15 T - 17 T
55.RS650601
0 - 76 mm
55.550620
55.250600
55.550629
55.550619
20 T - 25 T
55.RS650701
0 - 80 mm
55.550720
55.250700
55.550729
55.550719
30 T
55.RS650711
10 - 90 mm
55.550720
55.250700
55.550929
55.550719
All spare parts are available either separately or as repair sets.

It is recommended when any
parts are damaged to replace
them straight away and not to
take any risk.
When ordering spare parts
always give: model, lifting
capacity, jaw opening and serial
number as well as the needed
spare parts.
Revision Sets.
Capacity
Set nr.
Lock leverassy
Cam assy
Spring
Cam pin
Pivot
0.75 T
55.RV650000
55.550031
55.550020
55.250000
55.550029
55.550019
1T
55.RV650801
55.550831
55.550820
55.250800
55.550829
55.550819
1 TSE
55.RV650811
55.550831
55.550880
55.250800
55.550829
55.550819
1.5 T
55.RV650101
55.550131
55.550120
55.250100
55.550129
55.550119
2T
55.RV650901
55.550131
55.550920
55.250100
55.550129
55.550119
3T
55.RV650911
55.550131
55.550920
55.250100
55.552929
55.550119
4.5 T
55.RV650201
55.550231
55.550220
55.250200
55.550329
55.550219
4.5 TSE
55.RV650221
55.552431
55.552220
55.250200
55.550329
55.550219
6T
55.RV650301
55.550331
55.550320
55.250300
55.550329
55.550219
7.5 T
55.RV650401
55.550431
55.550420
55.250400
55.550429
55.550219
7.5 TSE
55.RV650611
55.552431
55.552620
55.250400
55.550429
55.550219
9T
55.RV650612
55.552531
55.552620
55.250400
55.555529
55.550219
12 T
55.RV650501
55.550531
55.550520
55.250500
55.550529
55.550219
15 T - 17 T
55.RV650601
55.550631
55.550620
55.250600
55.550629
55.550619
20 T - 25 T
55.RV650701
55.550731
55.550720
55.250700
55.550729
55.550719
30 T
55.RV650711
55.550731
55.550720
55.250700
55.550929
55.550719
Repair Sets - Hardox.

Capacity
Set nr.
Jaw opening
Cam assy
Spring
Cam pin
Pivot
0,75 T
55.RS650000.5
0 - 13 mm
55.550020.5
55.250000
55.550029
55.550019.5
1T
55.RS650801.5
0 - 18 mm
55.550820.5
55.250800
55.550829
55.550819.5
1 T TSE
55.RS650811.5
0 - 25 mm
55.550880.5
55.250800
55.550829
55.550819.5
1.5 T
55.RS650101.5
0 - 20 mm
55.550120.5
55.250100
55.550129
55.550119.5
2T
55.RS650901.5
0 - 35 mm
55.550920.5
55.250100
55.550129
55.550119.5
3T
55.RS650911.5
0 - 35 mm
55.550920.5
55.250100
55.552929
55.550119.5
4.5 TSE
55.RS650221.5
0 - 45 mm
55.552220.5
55.250200
55.550329
55.550219.5
6T
55.RS650301.5
0 - 32 mm
55.550320.5
55.250300
55.550329
55.550219.5
7.5 T TSE
55.RS650611.5
0 - 55 mm
55.552620.5
55.250400
55.550429
55.550219.5
119
Safely lifting vertical
120
Safely lifting horizontal
121
ELD contents
122
Contents
Page 122
Introduction ELD
Page 123
Certificates
Page
124
Quality control
Page
125
Markings
Page
126
Working load table
Page
127
Product overview
Page
128 - 131
Alloy steel chains Grade 8
Page
132
Master links
Page
133
Connecting links
Page
134
Web sling connecting links
Page
134
Eye hooks
Page
135
Clevis hooks
Page
136
Self locking hooks
Page
137
Shortening hooks
Page
138
Shortening hooks with safety
Page
139
Self locking swivel hooks
Page
140
Swivel hooks
Page
141 - 142
Swivels
Page
142 - 143
Sliding choker hooks
Page
144
Ramshorn swivel hooks
Page
144
Shank self locking hooks
Page
145
Shank hooks
Page
145
Machined shank self-locking hook
Page
146
Machined shank hooks
Page
146
Lifting Points
Page
147
Swivel basket
Page
147
Weld-on bucket hooks
Page
148
Load binders
Page
149
Tags for slings
Page
150
Chain assemblies
Page
151 - 152
Round sling assemblies
Page
153
Lashing chains
Page
154
Spare parts
Page
155 - 157
General instruction for use
Page
158 - 160
Load Capacity DIN 15402 and DIN 15401 hooks
Page
161
Products overview DIN hooks and blocks
Page
162
ELD introduction
ELD division of the Feat Group SpA is leader in design, application engineering and production of wire rope fittings,
grade 8 chain accessories, blocks and OEM components. The art of forging steel is a tradition at Feat Group S.p.A.
The heritage as a forging shop has enabled the company to become a worldwide supplier of a wide range of products
that are used directly or indirectly in petrochemical, nuclear, automotive, agricultural, earth moving and lifting industries.
The core of our business is drop forgings up to 100 kg, hammer forgings up to 500 kg and open die forgings for bigger sizes.
The strength of the company lies in the highly qualified staff of technicians. Starting from the specific enquiries of our
customers, draughtsman and engineers analyze the production problem beforehand through FMEA techniques, and by
means of computerized simulations of the forging dynamics they are able to realize prototypes of the items to be forged
(rapid prototyping) in very short time periods.
All products are certified (TUV, Lloyds Register, Nippon Kaiji Kyokai, DNV, BG) and covered by a specific insurance for
product liability. The certified quality system ISO 9001 permits the monitoring of all the aspects of the organization,
and the identification and traceability of the main documents of the company, with a view to achieving a continual and
consolidated improvement. In 2009 ELD obtained the H-88 approval by BGM Nord Sd.
123
Certificates
124
Quality control
Design
Rapid prototyping
Raw materials inspection
CNC machining
Dyes making
Forging lines
Heat treatment
Spectographic analysis
Metallographic test
Magnaflux control
Cycle testing
150 tons tensile testing
125
Markings
According to the EN818-4 all Grade 80 chain slings should be equipped with an octagonal tag.
All required markings are shown below.

Inspection interval
Individual identification mark
manufacturer symbol
CE marking
Grade
Nr of legs
Angle
Nominal thickness of the chain (mm)
Working load limit (t)
126
Working load table

Working load limit Grade 80 chain slings in t
Nominal thickness of the
chain in mm
1-leg
Angle
Load factor
6
7
8
10
13
16
19
20
22
26
32
2-leg
0
1
1,12
1,5
2
3,15
5,3
8
11,2
12,5
15
21,2
31,5
3- and 4-leg
Endless sling in choke
0<45
45<60
0<45
45<60
1,4
1,6
2,12
2,8
4,25
7,5
11,2
16
17
21,2
30
45
1
1,12
1,5
2
3,15
5,3
8
11,2
12,5
15
21,2
31,5
2,1
2,36
3,15
4,25
6,7
11,2
17
23,6
26,5
31,5
45
67
1,5
1,7
2,2
3
4,75
8
11,8
17
19
22,4
31,5
47,5
1,6
1,8
2,5
3,15
5
8,5
12,5
18
20
23,6
33,5
50
The table gives WLL information based on normal use conditions. In case of more demanding conditions such as edge loading, high temperatures
asymmetric loading, the given WLL values have to be reduced using the reducing factors mentioned below.

Inclinations >60 are prohibited
Reduced Working Load under unfavorable circumstances

The WLL of a chain sling should be reduced if used at temperatures >200according to the table:
Temperatur
-40C < T < +200C
+200C < T < +300C
+300C < T < +400C
Load factor
0,9
0,75
In case of temperatures below -40C, the manufacturer has to be consulted before using the chain.
In case of asymetric loading (individual chain legs have various angles or the different legs are unevenly loaded),
the Working Load has to be reduced with 50%.
Asymmeteric loading
2-leg
Load factor
3- and 4-leg
0<45
45<60
0<45
45<60
1,4
The use under unfavorable conditions (chemical, abrasive environment) should be negotiated with the producer.
The sling chains must not be placed in acid solutions nor be subjected to acid steams.
127
Product overview

Chain size
181
191
101
100
Page 134
Page 135
Page 135
Page 132
Page 133
Page 133
Page 134
41.01.06.0000
41.02.12.0707
41.10.34.0606
41.19.06.0000
41.22.06.0000
41.01.07.0000
41.02.12.0707
41.10.34.0707
41.19.08.0000
41.20.08.0000
41.22.07.0000
41.23.08.0000
41.01.08.0000
41.02.12.0807
41.10.34.0808
41.19.08.0000
41.20.08.0000
41.22.08.0000
41.23.08.0000
10
41.01.10.0000
41.02.12.1008
41.10.34.1010
41.19.10.0000
41.20.10.0000
41.22.10.0000
41.23.10.0000
13
41.01.13.0000
41.02.12.1310
41.10.34.1313
41.19.13.0000
41.20.13.0000
41.22.13.0000
41.23.13.0000
16
41.01.16.0000
41.02.12.1613
41.10.34.1616
41.19.16.0000
41.20.16.0000
41.22.16.0000
41.23.16.0000
18
41.01.18.0000
41.02.12.1816
41.10.34.1818
19
41.01.19.0000
41.02.1.22318
41.10.34.2020
41.19.20.0000
41.22.19.0000
20
41.01.20.0000
41.02.12.0020
41.10.34.2020
41.19.20.0000
41.22.22.0000
41.23.20.0000
22
41.01.22.0000
41.02.12.2823
41.10.34.2222
41.19.22.0000
41.22.26.0000
26
41.01.26.0000
41.02.12.3228
41.10.34.2626
41.19.26.0000
32
41.01.32.0000
41.02.12.3632
41.19.32.0000
179
102
103
183
184
105
106
Page 136
Page 137
Page 137
Page 138
Page 138
Page 140
Page 140
41.21.06.0000
41.25.06.0000
41.24.06.0000
41.26.06.0000
41.30.06.0000
41.31.06.0000
41.21.08.0000
41.25.08.0000
41.24.08.0000
41.27.08.0000
41.26.08.0000
41.30.08.0000
41.31.08.0000
41.21.08.0000
41.25.08.0000
41.24.08.0000
41.27.08.0000
41.26.08.0000
41.30.08.0000
41.31.08.0000
10
41.21.10.0000
41.25.10.0000
41.24.10.0000
41.27.10.0000
41.26.10.0000
41.30.10.0000
41.31.10.0000
13
41.21.13.0000
41.25.13.0000
41.24.13.0000
41.27.13.0000
41.26.13.0000
41.30.13.0000
41.31.13.0000
16
41.21.16.0000
41.25.16.0000
41.24.16.0000
41.27.16.0000
41.26.16.0000
41.30.16.0000
41.31.16.0000
18
19
20
41.21.20.0000
41.26.20.0000
Chain size
128
Product overview
Chain size
167
168
169
117
118
119
145
Page 141
Page 142
Page 143
Page 143
Page 144
Page 142
Page 141
41.32.06.0000
41.33.06.0000
41.32.07.0000
41.33.07.0000
41.37.08.0000
41.32.08.0000
41.33.08.0000
10
41.32.10.0000
41.33.10.0000
13
41.32.13.0000
41.33.13.0000
16
41.32.16.0000
41.33.16.0000
18
19
20
41.32.19.0000
-
41.33.19.0000
-
41.38.08.0000
41.37.08.0000
41.38.08.0000
41.37.100000
41.38.10.0000
41.37.13.0000
41.38.13.0000
41.37.16.0000
41.38.16.0000
41.34.16.0000
41.34.19.0000
-
41.37.19.0000
-
41.38.19.0000
-
41.39.16.0000
41.39.19.0000
-
41.35.005400
41.35.008000
41.35.011500
-
22
41.32.22.0000
41.33.22.0000
41.34.22.0000
41.37.22.0000
41.38.22.0000
41.39.22.0000
41.35.016000
26
41.32.26.0000
41.33.26.0000
41.34.26.0000
41.37.26.0000
41.38.26.0000
41.39.26.0000
41.35.022000
32
41.32.32.0000
41.33.32.0000
41.34.32.0000
41.37.32.0000
41.38.32.0000
41.39.32.0000
41.35.031500
104
121
521
504
113
Page 145
Page 145
Page 146
Page 146
Page 147
41.40.06.0000
41.41.06.0000
41.43.06.0000
41.42.06.0000
41.44.06.0000
41.40.08.0000
41.41.07.0000
41.43.07.0000
41.42.08.0000
41.40.08.0000
41.41.08.0000
41.43.08.0000
41.42.08.0000
41.44.08.0000
10
41.40.10.0000
41.41.10.0000
41.43.10.0000
41.42.10.0000
41.44.10.0000
13
41.40.13.0000
41.41.13.0000
41.43.13.0000
41.42.13.0000
41.44.13.0000
16
41.40.16.0000
41.41.16.0000
41.43.16.0000
41.42.16.0000
41.44.16.0000
Chain size
18
19
20
22
41.41.22.0000
41.43.22.0000
41.44.22.0000
26
41.41.26.0000
41.43.26.0000
41.44.26.0000
32
41.41.32.0000
41.43.32.0000
41.44.32.0000
41.41.19.0000
-
41.43.19.0000
-
41.44.19.0000
-
129
Product overview
WLL
112
700C
700U
115
Page 144
Page 148
Page 148
Page 147
0,3t
41.73.08.0000
0,5t
41.71.000500
0,6t
41.73.10.0000
1t
41.70.001000
41.71.001000
41.73.12.0000
1,5t
41.36.001500
1,6t
41.73.16.0000
2t
41.36.002000
41.70.002000
41.71.002000
2,5t
41.73.20.0000
3t
41.36.003000
41.70.003000
41.71.003000
4t
41.70.004000
41.71.004000
41.73.24.0000
5t
41.36.005000
41.70.005000
6t
41.70.006000
41.71.006000
6,3t
41.73.30.0000
8t
41.70.008000
41.71.008000
10t
41.70.010000
18t
41.70.018000
Chain size
183L
184L
1PELP
Page 139
Page 139
41.29.08.0000
41.28.08.0000
30.08.08.001
30.08.08.000
41.80.000081
30.00.08P
10
41.29.10.0000
41.28.10.0000
30.08.10.001
30.08.10.000
41.80.000082
30.00.10P
13
41.29.13.0000
41.28.13.0000
30.08.13.001
30.08.13.000
41.80.000083
30.00.13P
16
41.29.16.0000
41.28.16.0000
Page 149
Page 149
30.08.16.000
20
Page 157
Page 157
41.80.000084
41.80.000085

Spare parts
For hooks
RC
1DS5
RU
1PE
1SPEN
1DSEN
102KR
Page 155
Page 155
Page 155
Page 156
Page 156
Page 156
Page 157
112
103/179/184
179/100
101/121/167/
168/169/521
102/103/104/
105/106/504
130
Product overview
Tags
Page 150
Page 150
Page 150
Page 150
Page 150
Page 150
41.99.000001
41.99.000002
41.99.000003
41.99.000004
41.99.000005
41.99.000010
Chain
assemblies
Page 151
Page 151
Page 151
Page 151
Page 153
Page 153
Page 153
Page 153
Roundsling
assemblies
Lashing
chains
Page 154
Page 154
Corner
protection
Page 70
Page 70
Page 68
Page 68
Page 70
131
Alloy steel chains Grade 8

Alloy steel chains Grade 8, EN818-2
d
p
w1
w2
Ref. nr.
black painted
Chain size
WLL
Breaking load
Proof test
(kg)
kN
kN
Dimensions (mm)
d
Weight
Standard
length
w1
w2
(kg/m)
(m)
41.01.06.0000
6-8
1120
45,2
28,3
18
7,8
19,8
0,8
100
41.01.07.0000
7-8
1500
61,6
38,5
21
9,1
23,1
1,1
100
41.01.08.0000
8-8
2000
80,4
50,3
24
10,4
26,4
1,4
100
41.01.10.0000
10-8
3150
126
78,5
10
30
13,0
33
2,2
100
41.01.13.0000
13-8
5300
212
133
13
39
16,9
42,9
3,8
100
41.01.16.0000
16-8
8000
322
201
16
48
20,8
52,8
5,7
100
41.01.18.0000
18-8
10000
407
254
18
54
23,4
59,4
7,3
100
41.01.20.0000
20-8
12500
503
314
20
60
26,0
66
100
41.01.22.0000
22-8
15000
608
380
22
66
28,6
72,6
10,9
100
41.01.26.0000
26-8
21200
849
531
26
78
33,8
85,8
15,2
50
41.01.32.0000
32-8
31500
1290
804
32
96
41,6
105,6
23
50
Elongation at break is min 20%

Relation of WLL : Breaking load : Proof test = 1 : 2,5 : 4 (200 : 500 : 800 Mpa)

See Working load table for details regarding WLL for different applications and WLL reducing factors.
132
Master links
Master links
Master links according to EN 1677-4 (former DIN 5688-8), red epoxy painted, without flatpoint
WLL
1-leg
2-leg
41.02.12.0707
6/7
41.02.12.0807
41.02.12.1008
41.02.12.1310
Dimensions (mm)
Weight
(kg)
(kg)
A13
1600
13
110
60
0,34
A16
2120
16
110
60
0,53
10
A18
3150
18
135
75
0,80
13
10
A22
5300
22
160
90
1,50
41.02.12.1613
16
13
A26
8000
26
180
100
2,30
41.02.12.1816
18
16
A32
11200
32
200
110
3,90
41.02.1.22318
20/22/23
18
A36
16000
36
260
140
6,35
20
A40
18000
40
300
160
9,00
41.02.12.0020
41.02.12.2823
26/28
22/23
A45
25000
45
340
180
12,80
41.02.12.3228
32
26/28
A51
35500
51
350
190
17,2
41.02.12.3632
36
32
A57
45000
57
400
200
24,2
Ref. nr.
Dimensions (mm)
Chain size
Chain size
WLL
Weight
3- and 4-legs
(kg)
(kg)
2360
18
135
75
13
54
25
1.16
41.10.34.0707
AK18
3150
18
135
75
13
54
25
1.16
41.10.34.0808
AK22
4250
22
160
90
16
70
34
2.22
41.10.34.1010
10
AK26
6700
26
180
100
18
85
40
3.36
41.10.34.1313
13
AK32
11200
32
200
110
22
115
50
6.02
41.10.34.1616
16
AK36
17000
36
260
140
26
140
65
9.94
41.10.34.1818
18
AK45
21200
45
340
180
32
150
70
18.90
41.10.34.2020
20
AK51
26500
51
350
190
32
150
70
23.3
41.10.34.2222
22/23
AK51
35500
51
350
190
36
170
75
25.8
41.10.34.2626
26
AK57
45000
57
400
200
40
170
80
35.20
AK18
bx
A00
41.10.34.0606
Ref. nr.
133
Connecting links
Web sling connecting links
Connecting link, serie 181 (according to EN1677-1)
Ref. nr.
Chain size
WLL
Dimensions (mm)
(t)
Weight
LU
(kg)
41.19.06.0000
6-8
1,12
11
13
16
16,5
43
0,07
41.19.08.0000
7/8-8
9,5
13,5
18
20
23
55
0,16
41.19.10.0000
10-8
3,15
12
17
22
25
28
67
0,30
41.19.13.0000
13-8
5,3
17
22
26
30
34
84
0,60
41.19.16.0000
16-8
22
28
32
36
41
104
1,10
41.19.20.0000
20-8
12,5
25
33
40
44
49
120
1,90
41.19.22.0000
22-8
15
28
38
45
50
58
142
2,80
41.19.26.0000
26-8
21,2
32
48
50
54
65
170
4,90
41.19.32.0000
32-8
31,5
38
62
56
68
80
190
8,50
B
1
18
EL
XX
X-
3/4"
20-8
LU
Cmax
3/4"
X-
1
18
D
EL
XX
20-8
Web sling connecting link, serie 191 (according to EN1677-1)

Ref. nr.
Chain size
WLL
Dimensions (mm)
(t)
Weight
LU
41.20.08.0000
7/8-8
10,5
24
40
20
62
0,3
41.20.10.0000
10-8
3,15
12
28
50
25
78
0,6
41.20.13.0000
13-8
5,3
17
33
60
30
97
1,0
41.20.16.0000
16-8
21
42
75
36
118
2,0
1
18
XXX
D
EL
X
X-X
LU
7/8-8
191
ELD
7/8-8
134
(kg)
Eye hooks
Eye hook with safety latch, serie 101 (according to EN1677-2)
Ref. nr.
Chain size
WLL
Dimensions (mm)
Weight
(t)
D1
(kg)
41.22.06.0000
6-8
1,25
9,5
19
77
23
20
21
15
15
31
82
0,33
41.22.07.0000
7-8
1,6
11
25
82
26
22
23
18
18
34
93
0,45
41.22.08.0000
8-8
2,5
13
27
94
27
23
27
23
23
38
105
0,76
41.22.10.0000
10-8
3,2
15
32
106
31
27
31
23
24
42
121
1,08
41.22.13.0000
13-8
5,4
18
38
132
40
35
37
29
30
50
146
1,82
41.22.16.0000
16-8
23
51
165
51
43
49
37
37
62
187
3,80
41.22.19.0000
19-8
11,5
29
64
198
58
53
60
43
46
75
230
7,40
41.22.22.0000
22-8
16
33
70
222
66
58
67
52
57
84
255
10,70
41.22.26.0000
26-8
22
39
90
283
87
78
80
64
65
110
320
18,50
D1
Eye hook with safety latch, serie 100 (according to EN1677-2)

Ref. nr.
Chain size
WLL
Dimensions (mm)
(t)
A1
Weight
(kg)
41.23.08.0000
7/8-8
29
27
36
17
30
12
24
94
0,52
41.23.10.0000
10-8
3,15
40
37
45
24
35
16
32
122
1,05
41.23.13.0000
13-8
5,3
48
45
54
30
43
18
38
152
1,95
41.23.16.0000
16-8
56
53
70
35
50
24
50
202
4,40
41.23.20.0000
20-8
12,5
65
62
88
42
64
27
60
240
8,00
A1
135
Clevis hooks
Clevis chain hook with safety latch, serie 179 (according to EN1677-2)
Ref. nr.
Chain size
WLL
Dimensions (mm)
(t)
Weight
A1
(kg)
41.21.06.0000
6-8
1,12
24
21,5
23
13
22
7,8
20
68
21
0,25
41.21.08.0000
7/8-8
29
27
36
20
31
10
28
85
22
0,70
41.21.10.0000
10-8
3,15
38
35
45
24
35
12,5
35
105
28
1,25
41.21.13.0000
13-8
5,3
46
42
58
30
42
16
38
132
36
2,20
41.21.16.0000
16-8
53
48
64
35
48
20
50
148
42
3,10
41.21.20.0000
20-8
12,5
66
60
80
44
58
24
60
187
49
5,90
L
G
A1
136
Self locking hooks

Eye self locking hook, serie 102 (according to EN1677-3)
Ref. nr.
Chain size
WLL
Dimensions (mm)
(t)
Weight
(kg)
41.25.06.0000
6-8
1,12
22
28
20
14
139
35
107
11
0,5
41.25.08.0000
7/8-8
25
33
25
20
172
45
135
12
0,85
41.25.10.0000
10-8
3,15
10
32
44
35
27
218
58
168
14
1,6
41.25.13.0000
13-8
5,3
13
40
54,5
40
31
267
71
208
18
2,9
41.25.16.0000
16-8
16,5
50
67
52
40
330
84
254
22
5,9
E.
L.D
. 5 /8"
102
-8
16
XXX
-8
16
Clevis self locking hook, serie 103 (according to EN1677-3)

Ref. nr.
Chain size
WLL
Dimensions (mm)
(t)
Weight
(kg)
41.24.06.0000
6-8
1,12
14
28
20
20
2,5
35
99
135
0,55
41.24.08.0000
7/8-8
20
33
25
10
28
45
122
165
0,9
41.24.10.0000
10-8
3,15
27
44
35
12,5
35
58
151
207
1,65
41.24.13.0000
13-8
5,3
31
54,5
40
16
38
71
184
255
3,1
41.24.16.0000
16-8
40
67
52
20
50
84
212
300
6,1
E.
L.D
-8
16
. 5 /8"
10 3
-8
16
XXX
137
Shortening hooks
Eye grab hook, serie 183 (according to EN1677-1)
Ref. nr.
Chain size
WLL
Dimensions (mm)
(t)
Weight
(kg)
41.27.08.0000
7/8-8
35
15
54
25
63
95,5
30
0,31
41.27.10.0000
10-8
3,15
46
20
75
35
79
124
43
0,75
41.27.13.0000
13-8
5,3
57
25
93
40
98
154
52
1,52
41.27.16.0000
16-8
68
30
108
52
116
179
64
2,20
E
3
18
16
-8
X-X
X
D
EL
5/8
"
Clevis grab hook, serie 184 (according to EN1677-1)

Ref. nr.
Chain size
WLL
Dimensions (mm)
(t)
Weight
(kg)
41.26.06.0000
6-8
1,12
30
17
41
39,5
7,8
20
72
27
0,16
41.26.08.0000
7/8-8
36
22
54
54
10
28
96
30
0,33
41.26.10.0000
10-8
3,15
46
28
75
70
12,5
35
124
43
0,80
41.26.13.0000
13-8
5,3
57
36
93
86
16
38
154
52
1,60
41.26.16.0000
16-8
70
42
108
101
20
50
179
64
2,30
41.26.20.0000
20-8
12,5
80
79
134
123
24
60
219
90
4,8
d
A
138
4
18
16
-8
X-X
X
D
EL
5/8
"
Shortening hooks with safety

Eye grab hook with safety, serie 183L (according to EN1677-1)
Ref. nr.
Chain size
WLL
Dimensions (mm)
(t)
Weight
(kg)
41.29.08.0000
7/8-8
35
15
54
10
63
95,5
30
0,31
41.29.10.0000
10-8
3,15
46
20
75
13
79
124
43
0,75
41.29.13.0000
13-8
5,3
57
25
93
16
98
154
52
1,52
41.29.16.0000
16-8
68
30
108
20
116
179
64
2,20
E
3
13
18
-8
X-X
X
D
EL
1 /2
"
Suitable for lifting and lashing purposes
Clevis grab hook and safety, serie 184L (according to EN1677-1)

Ref. nr.
Chain size
WLL
(t)
Dimensions (mm)
A
Weight
(kg)
41.28.08.0000
7/8-8
36
22
54
54
10
28
96
30
0,33
41.28.10.0000
10-8
3,15
46
28
75
70
12,5
35
124
43
0,80
41.28.13.0000
13-8
5,3
57
36
93
86
16
38
154
52
1,60
41.28.16.0000
16-8
70
42
108
101
20
50
179
64
2,30
d
A
4
18
13
-8
X-X
D
EL
X1
/2"
Suitable for lifting and lashing purposes
139
Self locking swivel hook

Self locking swivel hook (rotation under load), serie 105 (according to EN1677-3)
Ref. nr.
Chain size
WLL
Dimensions (mm)
Weight
(t)
(kg)
1,25
10
34
27
20
16
35
162
38
63
39
12,5
0,9
41.30.06.0000
6-8
41.30.08.0000
7/8-8
10
31
33
26
20
45
188
38
63
39
12,5
1,3
41.30.10.0000
10-8
3,2
12,5
40
44
35
27
58
228
47
79
48
16
41.30.13.0000
13-8
5,4
15
50
54
41
30
71
285
58
96
60
19
41.30.16.0000
16-8
17,5
65
66
53
35
84
337
72
120
60
24
6,5
. WLL
8 t
4
10
-8
16
113
16-8
E.
L.D
XXX
-8
16
Self locking swivel hook (no rotation under load), serie 106 (according to EN1677-3)
Ref. nr.
Chain size
WLL
Dimensions (mm)
Weight
(t)
(kg)
41.31.06.0000
6-8
1,25
10
34
27
20
16
35
162
38
63
39
12,5
0,9
41.31.08.0000
7/8-8
10
31
33
26
20
45
188
38
63
39
12,5
1,3
41.31.10.0000
10-8
3,2
12,5
40
44
35
27
58
228
47
79
48
16
41.31.13.0000
13-8
5,4
15
50
54
41
30
71
285
58
96
60
19
41.31.16.0000
16-8
17,5
65
66
53
35
84
337
72
120
60
24
6,5
113
16-8
4
10
WLL 8 t
D.
E.
-8
16
140
-8
16
XXX
Swivel hooks
Swivel hook (rotation under load, light duty), serie 168 (according to EN1677-1)
Ref. nr.
Chain size
WLL
Dimensions (mm)
Weight
(t)
D1
(kg)
10
34
77
24
20
21
15
31
133
38
63
39
12,5
0,75
41.33.06.0000
6-8
1,25
41.33.07.0000
7-8
1,6
10
31
82
26
22
23
18
34
140
38
63
39
12,5
0,9
41.33.08.0000
8-8
2,5
12,5
42
94
27
23
27
23
38
163
47
79
48
16
1,3
41.33.10.0000
10-8
3,2
12,5
40
106
32
27
31
23
42
172
47
79
48
16
1,6
41.33.13.0000
13-8
5,4
15
50
132
40
35
37
29
50
213
58
96
60
19
3,5
41.33.16.0000
16-8
17,5
65
165
51
43
49
37
62
266
72
120
70
24
6,5
41.33.19.0000
19-8
11,5
22
68
198
58
53
60
43
75
310
82
136
82
27
8,5
41.33.22.0000
22-8
16
24
84
222
66
58
67
52
84
352
92
154
92
31
15
41.33.26.0000
26-8
22
29
107
283
87
78
80
64
110
434
115
191
108
38
24,5
41.33.32.0000
32-8
31,5
34
117
339
97
87
94
80
120
512
132
222
132
45
54
See drawing below
Swivel hook (rotation under load, heavy duty), serie 169 (according to EN1677-1)
Ref. nr.
Chain size
WLL
Dimensions (mm)
Weight
(t)
D1
(kg)
41.34.16.0000
16-8
17,5
65
165
51
43
49
37
62
266
72
120
70
24
6,5
41.34.19.0000
19-8
11,5
22
68
198
58
53
60
43
75
310
82
136
82
27
8,5
41.34.22.0000
22-8
16
24
84
222
66
58
67
52
84
352
92
154
92
31
15
41.34.26.0000
26-8
22
29
107
283
87
78
80
64
110
434
115
191
108
38
24,5
41.34.32.0000
32-8
31,5
34
117
339
97
87
94
80
120
512
132
222
132
45
54
N
M
Lubrication nipple on demand (from sizes 19 to 32)
D1
113
19-8
141
Swivel hooks
Swivel hook (no rotation under load), serie 167 (according to EN1677-1)

Ref. nr.
Chain size
WLL
Dimensions (mm)
Weight
(t)
D1
(kg)
41.32.06.0000
6-8
1,25
27
77
24
20
21
15
31
116
31
51
30
10
0,75
41.32.07.0000
7-8
1,6
10
31
82
26
22
23
18
34
140
38
63
39
12,5
0,9
41.32.08.0000
8-8
2,5
12,5
42
94
27
23
27
23
38
163
47
79
48
16
1,3
41.32.10.0000
10-8
3,2
12,5
40
106
32
27
31
23
42
172
47
79
48
16
1,6
41.32.13.0000
13-8
5,4
15
50
132
40
35
37
29
50
213
58
96
60
19
3,5
41.32.16.0000
16-8
17,5
65
165
51
43
49
37
62
266
72
120
70
24
6,5
41.32.19.0000
19-8
11,5
22
68
198
58
53
60
43
75
310
82
136
82
27
8,5
41.32.22.0000
22-8
16
24
84
222
66
58
67
52
84
352
92
154
92
31
15
41.32.26.0000
26-8
22
29
107
283
87
78
80
64
110
434
115
191
108
38
24,5
41.32.32.0000
32-8
31,5
34
117
339
97
87
94
80
120
512
132
222
132
45
54
N
M
D1
113
19-8
Swivel (no rotation under load), serie 117 (according to EN1677-1)
(kg)
7/8-8
63
31
38
12,5
149
174
39
1,1
41.37.10.0000
10-8
3,2
79
40
47
16
180
212
48
1,5
41.37.13.0000
13-8
5,4
96
50
58
19
224
262
60
3,5
41.37.16.0000
16-8
120
65
72
24
280
328
70
41.37.19.0000
19-8
11,5
136
68
82
27
308
362
82
7,5
41.37.22.0000
22-8
16
154
84
92
31
370
432
92
12
41.37.26.0000
26-8
22
191
107
115
38
447
523
108
21
41.37.32.0000
32-8
31,5
222
117
132
45
527
617
132
36
D
G
X-XX
(t)
41.37.08.0000
142
A
C
Weight
Dimensions (mm)
22-8
WLL
113
Chain size
Ref. nr.
Swivels
Swivel (rotation under load, light duty), serie 118 (according to EN1677-1)
Ref. nr.
Chain size
WLL
Dimensions (mm)
Weight
(t)
(kg)
41.38.08.0000
7/8-8
63
31
38
12,5
149
174
39
1,1
41.38.10.0000
10-8
3,2
79
40
47
16
180
212
48
1,5
41.38.13.0000
13-8
5,4
96
50
58
19
224
262
60
3,5
41.38.16.0000
16-8
120
65
72
24
280
328
70
41.38.19.0000
19-8
11,5
136
68
82
27
308
362
82
7,5
41.38.22.0000
22-8
16
154
84
92
31
370
432
92
12
41.38.26.0000
26-8
22
191
107
115
38
447
523
108
21
41.38.32.0000
32-8
31,5
222
117
132
45
527
617
132
36
A
C
113
22-8
Lubrication nipple on demand (sizes 19-32 mm)
X-XX
Swivel (rotation under load, heavy duty), serie 119 (according to EN1677-1)
Dimensions (mm)
(t)
(kg)
41.39.16.0000
16-8
120
65
72
24
280
328
70
41.39.19.0000
19-8
11,5
136
68
82
27
308
362
82
7,5
41.39.22.0000
22-8
16
154
84
92
31
370
432
92
12
41.39.26.0000
26-8
22
191
107
115
38
447
523
108
21
41.39.32.0000
32-8
31,5
222
117
132
45
527
617
132
36
A
C
Weight
G
22-8
WLL
113
Chain size
Ref. nr.
X-XX
Lubrication nipple on demand (sizes 19-32 mm)
143
Sliding choker hooks

Ramshorn swivel hook
Sliding choker hook, serie 112
Ref. nr.
Wire rope (mm)
Size (inch)
41.36.001500
10-13
41.36.002000
14-16
41.36.003000
17-18
41.36.005000
19-25
WLL
Dimensions (mm)
Weight
(t)
D1
(kg)
1,5
15
50
208
50
40
250
96
60
19
19
0,55
/8
17,5
65
238
60
48
293
120
70
24
13
24
0,9
/4
22
68
238
60
48
304
136
82
27
14
27
1,4
/8-1
24
84
301
75
60
371
154
92
31
23
31
3,5
/8 - /2
Ramshorn swivel hook (rotation under load, light duty), serie 145
Ref. nr.
Chain size
WLL
Dimensions (mm)
Weight
(t)
D1
(kg)
41.35.005400
2,5V
5,4
15
50
208
50
40
250
96
60
19
19
3,5
41.35.008000
4-V
17,5
65
238
60
48
293
120
70
24
13
24
6,5
41.35.011500
4-V
11,5
22
68
238
60
48
304
136
82
27
14
27
8,5
41.35.016000
6-V
16
24
84
301
75
60
371
154
92
31
23
31
15
41.35.022000
8-V
22
29
107
337
85
67
445
191
108
38
35
38
24,5
41.35.031500
10-V
31,5
34
117
377
95
75
485
222
132
45
60
45
54
N
M
Lubrication nipple on demand (sizes 11.5 to 31.5)
D1
F
C
144
Shank self locking hooks

Shank hooks
Shank self locking hook, serie 104 (according to EN1677-3)
Ref. nr.
Chain size
WLL
Dimensions (mm)
Weight
(t)
(kg)
41.40.06.0000
6-8
1,25
20
40
28
20
14
143
35
83
0,55
41.40.08.0000
7/8-8
20
42
33
25
20
181
45
114
0,9
41.40.10.0000
10-8
3,15
24
51
44
35
27
224
58
138
1,65
41.40.13.0000
13-8
5,3
28
64
54
40
31
277
71
173
3,1
41.40.16.0000
16-8
33
77
67
52
40
330
84
201
6,05
E.
L.D
. WLL
8 t
-8
10
16
XXX
-8
16
Shank hook, serie 121 (according to EN1677-1)

Ref. nr.
Chain size
WLL
(t)
Dimensions (mm)
A
D1
Weight
F
(kg)
41.41.06.0000
6-8
1,25
15
49
77
24
20
21
15
15
31
59
0,35
41.41.07.0000
7-8
1,6
17
57
82
26
22
23
18
18
34
67
0,55
41.41.08.0000
8-8
2,5
19
64
94
27
23
27
23
23
38
73
0,78
41.41.10.0000
10-8
3,2
23
69
106
32
27
31
23
24
42
82
1,1
41.41.13.0000
13-8
5,4
29
84
132
40
35
37
29
30
50
101
1,9
41.41.16.0000
16-8
36
92
165
51
43
49
37
37
62
126
3,8
41.41.19.0000
19-8
11,5
43
101
198
58
53
60
43
46
75
157
7,3
41.41.22.0000
22-8
16
48
112
222
66
58
67
52
57
84
167
10,5
41.41.26.0000
26-8
22
59
135
283
87
78
80
64
65
110
210
18,5
41.41.32.0000
32-8
31,5
85
244
339
97
87
94
80
80
120
250
39
D1
145
Machined shank self-locking hook

Machined shank hook
Machined shank self locking hook, serie 504 (according to EN1677-3)
Ref. nr.
Chain size
WLL
Dimensions (mm)
Weight
(t)
(kg)
41.40.06.0000
6-8
1,25
M14
17
39
28
24
21
35
122
0,55
41.40.08.0000
7/8-8
M16
17
42
33
24
24
45
156
0,9
41.40.10.0000
10-8
3,2
M20
20
50
44
29
30
58
188
1,65
41.40.13.0000
13-8
5,4
M24
25
63
54
37
36
71
236
3,1
41.40.16.0000
16-8
M30
30
76
67
45
46
84
272
6,05
E.
L.D
. WLL
8 t
4
10
-8
16
XX
-8
16
Machined shank hook, serie 521 (according to EN1677-1)

Dimensions (mm)
Weight
(t)
D1
(kg)
1,25
M12
12
29
88
20
17.5
19
0,3
41.41.07.0000
7-8
1,6
M16
16
42
109
22
25
24
0,5
41.41.08.0000
8-8
2,5
M18
18
48
121
23
29
27
0,7
41.41.10.0000
10-8
3,2
M20
20
50
132
27
29
30
41.41.13.0000
13-8
5,4
M24
25
62
163
35
37
36
1,7
41.41.16.0000
16-8
M30
30
75
201
43
44.5
46
3,5
41.41.19.0000
19-8
11,5
M36x3
40
86
242
53
48.5
55
6,8
41.41.22.0000
22-8
16
M42x3
45
101
268
58
58
65
9,5
41.41.26.0000
26-8
22
M52x3
55
117
327
78
62.5
80
17
41.41.32.0000
32-8
31,5
M64x4
65
145
395
87
78
100
35
6-8
D1
41.41.06.0000
WLL
Chain size
Ref. nr.
146
Lifting Point
Swivel basket
Lifting Point, SERIE 115
Ref.Nr.
Size
41.73.08.0000
41.73.10.0000
(t)
Fi
Lu
0,3
M8
14
0,6
M10
17
M12
21
41.73.12.0000
41.73.16.0000
41.73.20.0000
41.73.24.0000
41.73.30.0000
Dimensions (mm)
WLL
1,6
M16
27
2,5
M20
30
M24
36
6,3
M30
45
180
Ch
Weight
(kg)
0,24
17
30,5
31
40
10
49
30
0,25
0,26
22
45
42,5
56
16,5
72
13,3
45
32
60,5
59
85
25
113
20
60
0,91
0,95
2,91
3,03
Sicherheidsfaktor 5:1
360
Lu
Ch
Fi
Swivel basket, serie 113

Ref. nr.
Chain size
WLL
Dimensions (mm)
Hole
Thread
Weight
(t)
mm
mm
(kg)
41.44.06.0000
6-8
1,25
51
40
31
10
65,5
30
12,5
M12
0,75
41.44.08.0000
7/8-8
63
50
38
12,5
10
39
17,25
M16
0,9
41.44.10.0000
10-8
3,2
79
62
47
16
106
12,5
48
20,5
M20
1,3
41.44.13.0000
13-8
5,4
96
75
58
19
131
15
60
25,5
M24
1,6
41.44.16.0000
16-8
120
95
72
24
164
17,5
70
30,5
M30
3,5
41.44.19.0000
19-8
11,5
136
106
82
27
181
22
82
40,5
M36x3
6,5
41.44.22.0000
22-8
16
154
127
92
31
216
24
92
45,5
M42x3
8,5
41.44.26.0000
26-8
22
191
159
115
38
264
29
108
55,5
M52x3
15
41.44.32.0000
32-8
31,5
222
188
132
45
312
34
132
66
M64x4
24,5
113
16-8
X-XX
147
Weld-on bucket hooks

Weld-on bucket hook, C serie
Weight
(t)
L1
D1
(kg)
C201
105
67
76
30
21
0,75
41.70.002000
C202
130
83
93
35
25
1,15
41.70.003000
C203
133
84
100
35
25
1,25
41.70.004000
C204
177
110
125
42
38
2,70
41.70.005000
C205
185
113
133
44
40
3,00
41.70.006000
C206
198
120
141
50
40
3,50
41.70.008000
C208
250
150
169
60
45
7,10
41.70.010000
C210
10
262
160
170
65
50
8,00
41.70.018000
C218
18
290
180
190
80
50
10
10,80
41.70.001000
Dimensions (mm)
D1
B1
WLL
Size
Ref. nr.
L1
Weld-on bucket hook, U serie

Size
WLL
Dimensions (mm)
Weight
(t)
L1
D1
(kg)
41.71.000500
U200
0,5
95
87
63
23
20
0,75
41.71.001000
U201
105
99
75
25
23
1,15
41.71.002000
U202
123
109
86
30
27
1,25
41.71.003000
U203
145
133
101
35
31
2,70
41.71.004000
U204
152
142
107
35
31
3,00
41.71.006000
U206
205
185
127
40
40
3,50
41.71.008000
U208
216
205
139
50
40
7,10
D
1
Ref. nr.
B1
PEJO U 8TON
L1
148
Load binders
Ratchet type load binder with hooks, following EN12195-3
Ref. nr.
Chain size
Lashing
capacity
Min. breaking
strength
(kN)
(kN)
30.08.08.001
8-8
40
80,4
30.08.10.001
10-8
63
126
30.08.13.001
13-8
100
212
Dimensions (mm)
F
355
118
Weight
A1
A2
(kg)
588
752
4,9
602
766
5,3
710
870
7,4
Ratchet type load binder without hooks, following EN12195-3

Ref. nr.
Chain size
Lashing
capacity
Min. breaking
strength
(kN)
(kN)
A1
A2
(kg)
Dimensions (mm)
Weight
30.08.08.000
8-8
40
80,4
355
118
340
520
4,2
30.08.10.000
10-8
63
126
355
118
340
520
4,3
30.08.13.000
13-8
100
212
355
118
362
562
4,6
30.08.16.000
16-8
160
322
355
118
362
562
5,6
149
Tags for slings

Tag for lashing chain, without ring, galvanized
Ref. nr.
Type
41.99.000001
VDI2701 / EN 12195-3
Standard packing
1
Tags for chain slings, without ring, galvanized

Ref. nr.
Type
41.99.000002
Einstrang
41.99.000003
Mehrstrang
Single leg
Standard packing
Multi leg
BackPage
Tags for chain slings with welded ring 5x40, red painted RAL 3000 with next inspection marking
Ref. nr.
Type
41.99.000004
Einstrang
41.99.000005
Mehrstrang
Single leg
Multi leg
Standard packing
BackPage
Non-welded ring 5x40 for tags, galvanized
150
Ref. nr.
Standard packing
41.99.000010
Chain assemblies
Chain assEmblies grade 80
eye grab hook connected with ta serie 181

connecting link.
Clevis grab hook with 3 chain links
Grab hook available with or without safetypin
Grab hook available with or without safetypin
Explanation Article structure

42
08
01
250
Articlegroup
chain assemblies
Nen diameter
6/7/8/10
Grade type
A=G80
Number of legs
1/2/3/4
Hook type
Working length
in cm
Masterlink
A= standard type
Shorting
Number of
shorting
possibiliteis
0/1/2/3/4
Clevis Hook type 179
A = Without
Eye hook type 100
B = Eye grab hook type 183
Eye hook type 101
C = Eye grab hook with pin type 183L
Self locking clevis hook type 103
D = Clevis grab hook type 184
Self locking eye hook type 102
E = Clevis grab hook with pin type 184L
Eye grab hook type 183
Clevis grab hook type 184
Eye grab hook with pin type 183L
Clevis grab hook with pin type 184L
10
Self locking swivel hook (rotation under load) type 105
11
Self locking swivel hook (no rotation under load) type 106
12
Swivel hook (no rotation under load) type 167
13
Swivel hook (rotation under load) type 168
14
Connecting link type 181
15
Round sling connecting link type 191
16
Masterlink
151
Chain assemblies
Chain assEmblies grade 80
179
WLL
(kg)
101
103
102
167/168
105/106
chain
(mm)
Inside width of standard

master link (mm)
= 90
Total length of only the fittings in mm

incl. master link, connecting link(s) and hook(s)
1120
110 x 60
221
278
252
303
312
358
2000
110 x 60
250
314
325
287
355
383
408
3150
10
135 x 75
307
391
390
353
437
441
497
5300
13
160 x 90
376
480
474
428
536
541
613
8000
16
180 x 100
432
590
575
496
642
654
725
12500
20
260 x 140
567
740
0 45
152
100
45 60
1600
1120
110 x 60
221
278
252
303
312
358
2800
2000
135 x 75
275
339
350
312
380
408
433
4250
3150
10
160 x 90
332
416
415
378
462
466
522
7500
5300
13
180 x 100
396
500
494
448
556
561
633
11200
8000
16
200 x 110
452
610
595
516
662
674
745
17000
12500
20
300 x 160
607
780
0 45
45 - 60
2360
1700
135 x 75
300
357
331
382
391
437
4250
3000
160 x 90
370
434
445
407
475
503
528
6700
4750
10
180 x 100
437
521
520
483
567
571
627
11200
8000
13
200 x 110
531
635
629
583
691
696
768
17000
11800
16
260 x 140
652
810
795
716
862
874
945
26500
19000
20
350 x 190
807
980
0 45
45 - 60
2360
1700
135 x 75
300
357
331
382
391
437
4250
3000
160 x 90
370
434
445
407
475
503
528
6700
4750
10
180 x 100
437
521
520
483
567
571
627
11200
8000
13
200 x 110
531
635
629
583
691
696
768
17000
11800
16
260 x 140
652
810
795
716
862
874
945
26500
19000
20
350 x 190
807
980
TLX Round sling with on each leg a PES-TLX sleeve
TLX Round sling with on each leg a PVC protection sleeve
EXPLANATION ARTICLE STRUCTURE

43
Article group
Round sling
assemblies
02
WLL of the indiviQuality

Number of legs:
dual Round sling:
1/2/3/4
1/2/3/4/5T...

C=Round sling Techlon (TLX)

03
250
Hook type
Working length
in cm
Master link
A = Standard
Sleeve type
Free
Eye hook, 100 Serie
C = Techlon (TLX)
Eye hook, 101 Serie
D = PVC
Self locking eye hook, 102 Serie

100
WLL
(kg)
101
102
Type of Round
sling
b = 90
Inside width of standard master

link (mm)
110 x 60
-
Total length of only the fittings in mm

incl. master link, connecting links and hook(s)
327
369
1000
1000 kg
2000
2000 kg
110 x 60
328
339
369
3000
3000 kg
135 x 75
413
412
459
4000
4000 kg
160 x 90
506
500
562
5000
5000 kg
180 x 100
515
500
562
353
438
327
364
437
369
369
484
b 0 45
b 45 60
1400
2800
4200
1000
2000
3000
1000 kg
2000 kg
3000 kg
110 x 60
135 x 75
160 x 90
5600
4000
4000 kg
180 x 100
526
520
582
7000
5000
5000 kg
200 x 110
535
520
582
b 0 45
b 45 - 60
2100
1500
1000 kg
135 x 75
406
448
4200
3000
2000 kg
160 x 90
448
459
489
6300
4500
3000 kg
180 x 100
543
542
589
8400
6000
4000 kg
200 x 110
661
655
717
10500
7500
5000 kg
260 x 140
670
655
717
b 0 45
b 45 - 60
2100
1500
1000 kg
135 x 75
406
448
4200
3000
2000 kg
160 x 90
448
459
489
6300
4500
3000 kg
180 x 100
543
542
589
8400
6000
4000 kg
200 x 110
661
655
717
10500
7500
5000 kg
260 x 140
670
655
717
153
Lashing chains
lashing chains according the EN 12195-3
Lashing chain 1-part
Detail grab hook with safety pin
1 x Eye-eye ratchet, one side a clevis

grab hook and clevis hook with 5 chain links
(see detail picture). On the other side only a clevis
hook Total standard length 3 meter
1 x separate Ratchet with grab hooks

1 lashing chain both sides with clevis hook
Explanation Article structure

44
08
01
350
Article group
Chain size
Grade type
1 or 2-part
Hook type
Working length
Ratchet type
Shorting
Free
Clevis Hook type 179
Eye hook type 100
Eye hook type101
Eye grab hook with pin type 183L
9 Clevis grab hook with pin type 184L

A= Ratchet with grab hooks

B= Eye-eye ratchet
C= Without ratchet

A = Without
C = Eye grabhook with pin type 183L
E = Clevis grab hook with pin type 184L
Lashing chain grade 80

Chain (mm)
LC (kN)
40

1 x Ratchet grab hook /grab hook
1 x lashing chain both sides Clevis hook L=3mr
10
63
13
100
40
10
63
13
100
16
160

1 x Eye-eye ratchet, one side a clevis grab hook
and clevis hook with 5 chain links
On the other side only a clevis hook
Total standard length 3 meter
154
Spare parts
Safety latch kit weld-on bucket hook, type C
Dimensions (mm)
A
41.80.000060
C201
38
32,5
20
41.80.000061
C202-C203
43
37
25,5
41.80.000062
C204-C205-C206
62
55
34
41.80.000063
C208-C210-C218
84
74
44
PEJO
C2-3
Standard packing
For hooks
Ref. nr.
Safety latch kit weld-on bucket hook, type U

Dimensions (mm)
B
41.80.000070
U200-U201
46,5
41,5
20
41.80.000071
U202
57
50
26
41.80.000072
U203-U204
71,5
63
35
41.80.000073
U206-U208
86
74
42
10
Standard packing
PEJO
For hooks
Ref. nr.
Safety latch kit Sliding choker hook, series 112

Standard packing
Dimensions (mm)
A
41.80.000020
112 3/8"-1/2"
47
39
24
41.80.000021
112 5/8"
52
40
28
41.80.000022
112 3/4"
52
40
32
41.80.000023
112 7/8"-1"
62
41
35
For hooks
Ref. nr.
155
Spare parts
Safety latch kit for hooks, series 101, 121, 167, 168, 169, 521
Standard packing
Dimensions (mm)
A
41.80.000000
6-8
D1
39,5
32,5
17
41.80.000001
7-8
D2
43,5
35,5
23
41.80.000002
8-8 & 10-8
D3
49
41
25
41.80.000003
13-8
D4
61,5
51,5
29
41.80.000004
16-8
D5
77,5
67,5
35
41.80.000005
19-8
D6
87
76
37
41.80.000006
22-8
D7
96
85,5
49
41.80.000007
26-8
D8
131
116
54
41.80.000008
32-8
D9
152,5
135
64
Marking
For hooks
Ref. nr.
Safety latch kit for hooks, series 179

Standard packing
Dimensions (mm)
A
6-8
41,5
36
17
41.80.000041
7/8-8
52
44,5
22
41.80.000042
10-8
63,5
55
28
41.80.000043
13-8
79,5
69
30
41.80.000044
16-8
92
79,5
36
41.80.000045
20-8
111
96
45
41.80.000040
10-8
WARNING
THIS LATCH
NOT TO
CARRY LOAD
For hooks
Ref. nr.
Spare part kit for clevis hooks, series 103, 179, 184
For hooks
Standard packing
156
Dimensions (mm)
G
41.80.000030
6-8
20
2,5
41.80.000031
7/8-8
10
28
41.80.000032
10-8
12,5
35
41.80.000033
13-8
16
38
41.80.000034
16-8
20
50
41.80.000035
20-8
24
60
Ref. nr.
Spare parts
Spare part kit for safety hooks, series 102, 103, 104, 105, 106, 504
Ref. nr.
For hooks
Standard packing
41.80.000045
6-8
41.80.000046
7/8-8
41.80.000047
10-8
41.80.000048
13-8
41.80.000049
16-8
Safety pin kit for hooks, series 183L, 184L

Ref. nr.
For hooks
Standard packing
Dimensions (mm)
A
41.80.000081
7/8-8
41
41.80.000082
10-8
52,5
41.80.000083
13-8
63
41.80.000084
16-8
74
41.80.000085
20-8
92
Safety pin kit for load binder hooks

Ref. nr.
For load binder
Standard packing
30.00.08P
8-8
30.00.10P
10-8
30.00.13P
13-8
157
GENERAL INSTRUCTIONS FOR USE

For sling accessories with single arm this corresponds to the
values indicated in the table below:
1. General notices
Maximum work load
With reference to the contents of these instructions for use, ELD

Division of Feat Group SpA and Technotex/Unitex refuses any
responsibility in the event of:
The use of accessories in a manner contrary to national
safety and accident prevention legislation.

Incorrect choice or predisposition of the lifting apparatus
with which they shall be connected.
Failure to observe correctly these instructions for use.
Unauthorised modifications to the accessories.
Improper use or lack of ordinary maintenance
Use combined with non-conforming accessories
Diameter of grade 8 chain 8 (mm)
WLL
10
13
16
20
22
26
32
1,12
1,5
3,15
5,3
12.5
15
21,2
31,5
B. The grade
The grade must be determined in accordance with the compatibility with the component to which it will be connected. Each grade
is identified with a number and/or letter as indicated in the table
below.
Grade
2. Criteria of choice and life of accessory
Letter
Number
C
(carbon steel)
(lightly alloyed steel)
A
(alloyed steel)
ELD products can be used as indicated in the following table:

Criterion of choice
Series
Sling accessories
Lifting accessories
101
102
103
105
106
112
117
118-119
122-123
145
151
167
168-169
179
181
183
184
302
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
-
The parameters which must be carefully considered in choosing

are as follows
C. Temperature of use:
The temperature of use shall be included in the range indicated in the
table below, bearing in mind the variation of the lifting capacity on the
basis of the temperature
Climatic conditions of use

Load expressed as a % of maximum load
Grade
Temperature, t., C
-20< t 200
200< t 300
300< t 400
-40< t 200
100
90
75
100
90
75
90
75
100
A. Maximum work load (WLL or lifting capacity)
D. Life span and frequency of use:
If the hook is used as a sling accessory, the maximum
The life span of this accessory is anticipated as being for 20,000

operational cycles at full load.
work load depends on the grade and configuration
If the hook is used as a lifting accessory, the maximum

work load is indicated on the part (WLL)
158
3. Marking
Marking and/or nameplates are set out in an indelible manner
concerning the anticipated use as indicated below.

6. Preliminary checks
Marking
Relative indication
Before starting up and/or assembling:
Sling accessories
Lifting accessories
Identification of manufacturer
Identification of product
(excluding series 112,122,123)
Identification of production lot
Diameter of chain in inches

(only series 102,103,179,181,183,184)
Diameter of rope in inches

(only series 112)
7. Installation, assembly instructions
See the instructions for use for each product available

on our website.
Maximum work load (lifting capacity)

(einschlielich Serie 112)
Angabe Gteklasse mit der Nummer
oder Buchstaben
(excluding series 122,123)
CE Logo
You are advised to read the instructions
ATTENTION ! for use specific to each product on our

website
The following loads cannot

be moved:
check the accessory to ensure especially that there are no
cuts,bends, incisions, abrasions, cracks, corrosion, or parts

missing such as, for example, the load-bearing pin and the
elastic blocking pin.
check for the presence of markings.
8. Suitability for use

The accessory has been subjected to testing by the manufacturer, in
order to assess its functional response and performance. The certificate, which is supplied with the accessory, attests to a successful
outcome of the tests carried out.
The user must, in every case and before carrying out operations,
check this functional response and performance of the accessory
when installed in order to confirm the suitability of the whole installation for use.
those whose weight exceeds the lifting capacity of the
accessory.
those whose surface temperature exceeds that admissible.
those whose surface is not sufficiently resistant to the
pressure exerted by the action of pick-up.
those classified as dangerous (e.g.: inflammable or
explosive materials, etc.).
those which could change their static configuration
and/or their centre of gravity, or their physical-chemical state.
those immersed in acid or exposed to acidic vapours
5. Restrictions on installation
If used with chains, sling accessories must only be used in
connection with chains of average tolerance for sling chain
conforming to EN 818-2 with the help of a connecting link.
For different uses, contact the manufacturer.
If used with ropes, sling accessories must only be used in connection with metal ropes suitable for the purpose, considering
the lifting capacity and dimensions.
Lifting accessory can only be used if installed in connection
with pick-up or hook-up units suitable for the purpose, bearing
in mind the lifting capacity and dimensions; the suspension or
pick-up of the accessory must be carried out in such a way as
to ensure its mobility around a supporting point thereby constituting
an articulated hinge; and no force, interference or rigid connection
must exist between the suspension element and the hook or
hook-up point with the lifting pick-up unit.
9. Using the accessory pick-up and manoeuvre

Use, load pick-up and manoeuvre with the accessory must be made
with great attention, delicately and without jerking. The possible safety latch opens manually by applying pressure to the device itself and
it closes automatically as a result of the strength of the spring. This
closing device does not hold the load under tension, that is the pickup element is slack, precisely to permit unhooking. For this reason,
always check that it is the hook which supports the load.
ATTENTION !
The latch must never support the load
Do not introduce more than two arms into our products and the
maximum angle compared to the vertical must never exceed
those indicated below.
45
45
45
45
45
45
45
45
ma
x6
45
45
45
45
x6
ma
ma
x6
x6
ma
159

For products where hook rotation is possible, take care that it is
permitted when loaded
ATTENTION !
Rotation when loaded is not
permitted for series 106+117+167
10. Restrictions on use.

Using the accessory for purposes which are not anticipated, its
improper use, its use in dangerous conditions and the failure to
carry out maintenance can all lead to situations of serious danger
to persons thus exposed as well as to the work setting, and can
also affect the functioning and safety of the accessory negatively.
The actions indicated below, which obviously do not cover all
possible examples of bad use of the accessory, are however
those which could reasonably be predicted. So:
NEVER use the accessory to lift and move persons,
animals and things different from those which the hook

is designed to be used.
NEVER raise loads with the point of the hook.
NEVER raise or move loads in flight (i.e. aircraft) nor use
the accessory to drag bound loads.
NEVER operate in areas where the use of non-flammable/
spark-proof components is required or in the presence of
strong electromagnetic fields.
NEVER weld metallic elements to the accessory, add
welded elements or use it as a weight for welding purposes.
11. Inspection and maintenance.

This includes operations of maintenance, carried out by personnel
who have been trained for the purpose, concerning checks during
use and possible actions as anticipated in the Table of maintenance and check-up operations.
The accessory must be subjected to the following checks:
Records of these checks must be kept safe
visual: check for the presence of surface defects such as

cracks, incisions, cuts or fissures, abrasions.
functional: check the accessory and the connecting link can

move freely, the latch carries out the function of unhooking,
and especially the spring keeps the blocking mechanism
functioning.
160
dimensional control: take and record the critical dimensions
as indicate in the specific instruction for use available in our

website before the first putting into service.
deformation: check that the accessory does not lose its shape
by measuring critical dimensions as indicated in the specific
instruction for use available in our website
wear and tear: check that points of contact are not worn out by
measuring critical dimensions as indicated in the specific
instruction for use available in our website.
lubrication: apply a grease film on moving parts within the
accessory.
state of preservation: check for the presence of excessive
oxidisation and corrosion, above all in cases where it is used
in the open air; check for the presence of cracks with suitable
methods (e.g. penetrating liquids) .
12. Demolition and scrapping of the accessory

If the accessory should turn out to be deformed, worn out or at the
end of its life span as indicated by the manufacturer, and therefore
no longer usable, it must be demolished and scrapped.
Table of maintenance and check-up operations
Description of check-up
Ordinary
Day
Visual
Functional
Deformation
Wear and tear and
lubrication
State of preservation
Periodical
Week
Month
Year
X
X
X
Replace the accessory when it is permanently deformed or there are section reductions as indicated in the instructions for use for each
product which you can find on our website.
Load Capacity DIN 15402

and DIN 15401 hooks
Load Capacity according UNI 9465 - DIN 15400
class
Driving Gear Group
M
P
S
1Bm M3
1Bm M3
1Am M4
2m M5
3m M6
4m M7
1Bm M3
1Am M4
2m M5
3m M6
4m M7
5m M8
1Am M4
2m M5
3m M6
4m M7
5m M8
4m M7
5m M8
1Bm M3
1Am M4
2m M5
3m M6
1Bm M3
1Am M4
2m M5
3m M6
4m M7
012
630
500
400
320
250
200
160
125
100
020
1.000
800
630
500
400
320
250
200
160
125
025
1.250
1.000
800
630
500
400
320
250
200
160
04
2.000
1.600
1.250
100
800
630
500
400
320
250
05
2.500
2.000
1.600
1.250
1.000
800
630
500
400
320
08
4.000
3.200
2.500
2.000
1.600
1.250
1.000
800
630
500
Hook
Load Capacity in Kg
5.000
4.000
3.200
2.500
2.000
1.600
1.250
1.000
800
630
1,6
8.000
6.300
5.000
4.000
3.200
2.500
2.000
1.600
1.250
1.000
2,5
12.500
10.000
8.000
6.300
5.000
4.000
3.200
2.500
2.000
1.600
20.000
16.000
12.500
10.000
8.000
6.300
5.000
4.000
3.200
2.500
25.000
20.000
16.000
12.500
10.000
8.000
6.300
5.000
4.000
3.200
32.000
25.000
20.000
16.000
12.500
10.000
8.000
6.300
5.000
4.000
40.000
32.000
25.000
20.000
16.000
12.500
10.000
8.000
6.300
5.000
50.000
40.000
32.000
25.000
20.000
16.000
12.500
10.000
8.000
6.300
12
63.000
50.000
40.000
32.000
25.000
20.000
16.000
12.500
10.000
8.000
16
80.000
63.000
50.000
40.000
32.000
25.000
20.000
16.000
12.500
10.000
20
100.000
80.000
63.000
50.000
40.000
32.000
25.000
20.000
16.000
12.500
25
125.000
100.000
80.000
63.000
50.000
40.000
32.000
25.000
20.000
16.000
32
160.000
125.000
100.000
80.000
63.000
50.000
40.000
32.000
25.000
20.000
40
200.000
160.000
125.000
100.000
80.000
63.000
50.000
40.000
32.000
25.000
50
250.000
200.000
160.000
125.000
100.000
80.000
63.000
50.000
40.000
32.000
63
320.000
250.000
200.000
160.000
125.000
100.000
80.000
63.000
50.000
40.000
80
400.000
320.000
250.000
200.000
160.000
125.000
100.000
80.000
63.000
50.000
100
500.000
400.000
320.000
250.000
200.000
160.000
125.000
100.000
80.000
63.000
500.000
400.000
320.000
250.000
200.000
160.000
125.000
100.000
80.000
125
This table estabishes a general classification of cranes based on the number of operating cycles to be carried out during the
expected life of the crane and a load spectrum factor which represents a nominal state of loading. Classification considers only
the operating conditions which are independent of the type of crane and the way it is driven.
161
Products overview DIN

hooks and blocks
DIN15402
DIN15401
Overhead crane blocks
Special blocks
Special blocks
162
Disclaimer: The information contained in this brochure has been prepared for promotional purposes and should only be used for guidance.
This information should not be considered as a guarantee under any circumstances. Technotex/unitex makes no warranty, expressed or implied,
and assumes no legal liability or responsibility for the accuracy, completeness or usefulness of any information contained herein. If additional
information is required, please contact your local Technotex sales representative.
163

Catalogo Eslingas y Cables TENSO

Uploaded by

Copyright:

Available Formats

Catalogo Eslingas y Cables TENSO

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Catalogo Eslingas y Cables TENSO

Uploaded by

Copyright:

Available Formats

General Catalogue

Web Slings Round Slings & lashings

Height Safety Products

Lifting Clamps & Equipment

Chains & Fittings

Web Slings Round Slings & lashings

Height Safety Products

Lifting Clamps & Equipment

Chains & Fittings

Wll capacity table for webbing and roundsling

Working Load Limits with 1 webbing sling or roundsling

Working Load Limits with 2 webbing slings

Wll capacity table for ULTRALIFT roundslings

Working Load Limits with 2 webbing slings

Web slings Round slings

Web slings Roundslings

3) Lifting of loads (WLL Capacity table and lifting angle)

Thick- Eye length

Eye length Standard

Folded eye width from one side

Folded eye width from two sides

Folded eye 1/3 width

MCEE / MCED endless web slings

Weight 1 meter in kg (L1)

MCED ENDLESS WEB SLINGS 2-LAYER

Weight 1 meter in kg (L1)

MCDDS 2-layer web slings with triangles (Male/Female)

Weight 2 meter in kg (L1)

Weight per Piece in kg

Technical information for MCDDS female triangles

Weight per Piece in kg

TE/ DT Round slings

Weight of round sling o,5 m

Weight per 0,5 m

DT round slings with double sleeve

cross section of a DT roundsling sleeve

Weight of round sling o,5 m

Weight per 0,5 m

TLX Premium round slings

the high tech round sling made from polyester

Weight of round sling o,5 m

Weight per 0,5 m

* Always consult the producer.

ULLD Round slings

ULTRALIFT LD Round slings are produced out of a Dyneema

ULTRALIFT LD RONDSLINGS (ULLD)

sleeve type 0,5 up to 2,0 Mtr

Sleeve type from 2 mtr and up

ULLD Round slings

ULTRALIFT LD ROUND SLINGS With LIGHT DUTY SLEEVE (ULLD)

ULCS coil slings

Sleeve width actual ULLD Roundsling

Sleeve width extra UPHD protection sleeve actual Roundsling

* Always consult the producer.

Techlon round slings comply with the Machinery Directive 2006/42/EG

TLX round slings

Weight of a TLX round sling with Techlon sleeve in kg

Extra per mtr.

TLX round slings

Extra per mtr.