AP-SERIES

BASIC PA SYSTEM

AP-200P

70W MIXER AMPLIFIER

AP-300P

130W MIXER AMPLIFIER

AP-600P

260W MIXER AMPLIFIER

AP-1000P

360W MIXER AMPLIFIER

AP-70M AP-130M AP-260M AP-360M AP-811P AP-8360 AP-8460 AP-8660 AP-1000A AP-1500A

70W MIXER AMPLIFIER 130W MIXER AMPLIFIER 260W MIXER AMPLIFIER 360W MIXER AMPLIFIER 9-INPUT MIXER PRE-AMPLIFIER 360W POWER AMPLIFIER 460W POWER AMPLIFIER 660W POWER AMPLIFIER

1000W POWER AMPLIFIER 1500W POWER AMPLIFIER

AP-812M

10-CHANNEL MONITOR PANEL

AP-815E

EMERGENCY PANEL

AP-813A

16-ZONE SPEAKER SELECTOR

AP-813B

2 X 5-ZONE SPEAKER SELECTOR

AP-813D

10-ZONE SPEAKER SELECTOR

AP SERIES

Cost Effective Mixer Amp

5-INPUT MIXER AMPLIFIERS
Highly flexible mixer amplifiers for a wide variety of voice and background music applications such as retail shops, restaurants and bars, service centers, houses of worship, warehouses and many more. Main features are

AP-200P

AP-300P

3 microphone and 2 auxiliary inputs 1 line output 100V, 70V and 4-16 Ohms transformerisolated speaker outputs Automatic mute function for paging and announcements Individual input gain controls with master volume control Bass and treble tone controls LED level meter Speaker output short circuit protection

AP-600P

AP-1000P

REAR PANEL

SPECIFICATIONS
Rated Power Output Output Regulation Speaker Output Input Output Frequency Response THD S/N Ratio Tone Controls Controls Cooling Indicators Protection Power Consumption Power Requirments Dimensions Built-in Dimensions Carton Dimensions Net Weight Gross Weight Finish

AP-200P
70W

AP-300P
130W

AP-600P
260W

AP-1000P
360W

Less than 3 dB (no load to full load) 70 ohms (70V) 143 ohms (100V) Low impedance: 4-16 ohms 38 ohms (70V) 77 ohms (100V) Low impedance: 4-16 ohms 19 ohms (70V) 39 ohms (100V) Low impedance: 4-16 ohms 14 ohms (70V) 28 ohms (100V) Low impedance: 4-16 ohms

MIC 1, 2, 3: 600 ohms, 5mV, unbalanced, phone jack; AUX 1, 2: 10k ohms, 470mV, unbalanced, RCA jack 600 ohms, >650mV, RCA jack 60 - 15,000 Hz, +/- 3dB Less than 0.5% at 1kHz (1/3 Rated Power) Better than 73dB BASS: 100 Hz (+/- 10dB), TREBLE: 12k Hz (+/- 10dB) 5 input gain, 1 treble, 1 bass, 1 mute, and power switch Internal 12VDC fan, extensive heat sinking Power indicator LED, LED output level meter 0, 2, 4, 6, 8, 10dB AC Fuse: 4A AC Fuse: 6A Current limiter, short circuit and thermal protection circuits 140W 220-240V AC, 50/60 Hz 89(H) x 483(W) x 366(D) mm 2 U rack 19 inch 185(H) x 520(W) x 435(D) mm 10.04kg 11.72kg Panel: steel plate, black Case: steel plate, black 11.36kg 13.02kg 13.68kg 15.32kg 14.08kg 15.70kg 260W AC Fuse: 8A 350W AC Fuse: 8A 485W

10

AP SERIES

AP Mixer Amp Series

5-INPUT MIXER AMPLIFIERS
Highly flexible mixer amplifiers for a wide variety of voice and background music applications such as retail shops, restaurants and bars, service centers, houses of worship, warehouses and many more. Main features are

AP-70M

3 microphone and 2 auxiliary inputs 1 line output 100V, 70V and 4-16 Ohms transformerisolated speaker outputs Automatic mute function for paging and announcements Individual input gain controls with master volume control Bass and treble tone controls LED level meter Speaker output short circuit protection

AP-130M

AP-260M

AP-360M

REAR PANEL

SPECIFICATIONS
Rated Power Output Output Regulation Speaker Output Input Output Frequency Response THD S/N Ratio Tone Controls Controls Cooling Indicators Protection Power Consumption Power Requirments Dimensions Built-in Dimensions Carton Dimensions Net Weight Gross Weight Finish

AP-70M
70W

AP-130M
130W

AP-260M
260W

AP-360M
360W

Less than 3 dB (no load to full load) 70 ohms (70V) 143 ohms (100V) Low impedance: 4-16 ohms 38 ohms (70V) 77 ohms (100V) Low impedance: 4-16 ohms 19 ohms (70V) 39 ohms (100V) Low impedance: 4-16 ohms 14 ohms (70V) 28 ohms (100V) Low impedance: 4-16 ohms

MIC 1, 2, 3: 600 ohms, 5mV, unbalanced, phone jack; AUX 1, 2: 10k ohms, 470mV, unbalanced, RCA jack 600 ohms, >650mV, RCA jack 60 - 15,000 Hz, +/- 3dB Less than 0.5% at 1kHz (1/3 Rated Power) Better than 73dB BASS: 100 Hz (+/- 10dB), TREBLE: 12k Hz (+/- 10dB) 5 input gain, 1 treble, 1 bass, 1 mute, and power switch Internal 12VDC fan, extensive heat sinking Power indicator LED, LED output level meter 0, 2, 4, 6, 8, 10dB AC Fuse: 4A AC Fuse: 6A Current limiter, short circuit and thermal protection circuits 140W 260W AC Fuse: 8A 350W AC Fuse: 8A 485W

110-120V or 220-240V AC, 50/60 Hz 24V DC 24V DC 89(H) x 483(W) x 366(D) mm 2 U rack 19 inch 185(H) x 520(W) x 435(D) mm 10.04kg 11.72kg Panel: steel plate, black Case: steel plate, black 11.36kg 13.02kg 13.68kg 15.32kg 14.08kg 15.70kg

11

AP SERIES

SPEAKERS

MIC 3 MIC 2 MIC 1

CD PLAYER

DUAL CASSETTE DECK

AP-811P
9-INPUT MIXER PRE-AMPLIFIER
The AP-811P is a versatile mixer pre-amplifier with 4 microphone inputs, 3 auxiliary inputs, 2 emergency inputs (high priority) and mute function. MIC1, EMC1, EMC2 are priority inputs, automatically muting all other signal inputs. MIC1 has the highest priority, able to suppress all other inputs. Output from the AP-815E emergency panel to EMC1 provides for alarm siren or emergency announcement to be broadcast over the public address system
POWER AMPLIFIER MIC 1 EMERGENCY PANEL AP-815E

AM/FM TUNER

AP-F508R

AP-811P

SPEAKERS

AP-8360

9 inputs, 2 outputs Automatic mute function for paging and announcements Individual input gain controls with master volume control Bass and treble tone controls
SPECIFICATIONS
Input Output Frequency Response S/N Ratio THD Tone Controls Muting Function

AP-811P
MIC 1, 2, 3, 4: 600 ohms, 5mV, unbalanced, phone jack AUX 1, 2, 3: 10k ohms, 200mV, unbalanced, RCA jack EMC 1, 2: 10k ohms, 200mV, unbalanced, phone jack 600 ohms, 775mV, 0 dB, RCA jack 60Hz - 15kHz (+/- 3dB) Better than 70dB Less than 0.1% at 1kHz BASS: 100 Hz (+/- 10dB), TREBLE: 12k Hz (+/- 10dB) MIC1 overrides other input signals with 0~30 dB attenuation EMC1 overrides other input signals except MIC 1 110-120V or 220-240V AC, 50/60 Hz; 24VDC 89(H) x 483(W) x 366(D) mm

REAR PANEL
Power Requirements Dimensions

12

AP SERIES

AP Power Amp Series

SINGLE CHANNEL POWER AMPLIFIERS
These commercial-grade power amplifiers efficiently deliver up to 660 watts of clean, reliable audio for the most demanding public address applications. Rugged and over-built to give years of dependable service, they are equipped with massive torrodial power transformers, extensive heat-sinking and fan cooling, protective circuits such as over-temperature, short circuit, RFI and soft start.

AP-8360

AP-8460

100V, 70V and 4-16 Ohms transformerisolated speaker outputs Combination XLR/RCA Line In and Line Out connectors LED status indicators Speaker output short circuit protection

AP-8660

REAR PANEL

SPECIFICATIONS
Rated Power Output Output Regulation Speaker Output Input Output Frequency Response THD S/N Ratio Slew Rate Controls Cooling Indicators Protection Power Consumption Power Requirments Dimensions Built-in Dimensions Carton Dimensions Net Weight Gross Weight Finish

AP-8360
360W Less than 3 dB (no load to full load) 13.6 ohms (70V), balanced 27.8 ohms (100V), balanced Low impedance: 4-16 ohms, balanced

AP-8460
460W

AP-8660
660W

10.7 ohms (70V), balanced 21.7 ohms (100V), balanced Low impedance: 4-16 ohms, balanced

7.4 ohms (70V), balanced 15.1 ohms (100V), balanced Low impedance: 4-16 ohms, balanced

Less than 1V, unbalanced, XLR and phone jack 775V, 0dB, XLR and phone jack 60 - 16,000 Hz, +/- 3dB Less than 0.5% at 1kHz (1/3 Rated Power) Better than 73dB 15V/uS Volume control and power switch Internal 12VDC fan, extensive heat sinking Power, Clip, Signal, Protect, and Temp LEDs AC Fuse: 10A AC Fuse: 12A Current limiter, short circuit and thermal protection circuits 485W 110-120V or 220-240V AC, 50/60 Hz 24V DC 89(H) x 483(W) x 366(D) mm 2 U rack 19 inch 185(H) x 520(W) x 435(D) mm 15.12kg 16.76kg Panel: steel plate, black Case: steel plate, black 17.66kg 19.30kg 20.8kg 22.3kg 620W 110-120V or 220-240V AC, 50/60 Hz AC Fuse: 15A 880W 110-120V or 220-240V AC, 50/60 Hz

13

AP SERIES

AP High Power Amps

SINGLE CHANNEL POWER AMPLIFIERS

AP-1000A

All the great features of the AP power amp series but when even more power is required, these AP-series high power amps provide up to 1500 watts into low impedance or 70/100V constant voltage speaker loads.

100V, 70V and 4-16 Ohms transformerisolated speaker outputs

AP-1500A

Combination XLR/RCA Line In and Line Out connectors LED status indicators: power, clip, signal, protect and high temperature Speaker output short circuit protection

REAR PANEL

SPECIFICATIONS
Rated Power Output Output Regulation Speaker Output Input Output Frequency Response THD S/N Ratio Slew Rate Controls Cooling Indicators Protection Power Consumption Power Requirments Dimensions Built-in Dimensions Carton Dimensions Net Weight Gross Weight Finish

AP-1000A
1000W Less than 3 dB (no load to full load) 4.9 ohms (70V), balanced 10.0 ohms (100V), balanced Low impedance: 4-16 ohms, balanced Less than 1V, unbalanced, XLR and phone jack 775V, 0dB, XLR and phone jack 50 - 18,000 Hz, +/- 1.5dB Less than 0.5% at 1kHz (1/3 Rated Power) Better than 105dB 40V/uS Volume control and power switch Internal 12VDC fan, extensive heat sinking Power, Clip, Signal, Protect, and Temp LEDs AC Fuse: 20A Current limiter, short circuit and thermal protection circuits 1350W 110-120V or 220-240V AC, 50/60 Hz 133(H) x 483(W) x 366(D) mm 3 U rack 19 inch 185(H) x 520(W) x 435(D) mm 25.0kg 27.5kg Panel: steel plate, black Case: steel plate, black

AP-1500A
1500W

3.3 ohms (70V), balanced 6.7 ohms (100V), balanced Low impedance: 4-16 ohms, balanced

2000W

27.0kg 30.0kg

14

AP SERIES

AP Power Amp Series

SINGLE CHANNEL POWER AMPLIFIERS
These commercial-grade power amplifiers efficiently deliver up to 360 watts of clean, reliable audio for the most demanding public address and voice alarm applications. Rugged and over-built to give years of dependable service, they are equipped with massive torrodial power transformers, extensive heat-sinking and fan cooling, protective circuits such as over-temperature, short circuit, RFI and soft start.
AMP DC

AC

Front Panel
4

ok

ok

ok

VOLUME
5 6 7 8 9 0 10

AP-8260I
260W AMPLIFIER

3 POWER 2 4 6 8 2 1

Amplifier

DC

AC

OK

OK

OK

Pin 1,2 Pin 2,4 Pin 5,6 AC Fault DC Fault AMP Fault

100V, 70V and 4-16 Ohms transformerisolated speaker outputs Combination XLR/RCA Line In and Line Out connectors

LED indicator in front and dry contact in rear panel for amplifier fault monitor LED indicator in front and dry contact in rear panel for AC fault monitor LED indicator in front and dry contact in rear panel for DC fault monitor

Rear Panel

SPECIFICATIONS
Rated Power Output Output Regulation Speaker Output Input Output Frequency Response THD S/N Ratio Slew Rate Controls Cooling Indicators Protection Power Consumption Power Requirments Dimensions Built-in Dimensions Carton Dimensions Net Weight Gross Weight Finish

AP-8260I
260W

AP-8360I
360W

Less than 3 dB ( From no signal to full working situatio ) 10.7 ohms (70V), balanced 21.7 ohms (100V), balanced Low impedance: 4-16 ohms, balanced Less than 1V, unbalanced, XLR and phone jack 775V, 0dB, XLR and phone jack 60 - 16,000 Hz, +/- 3dB Less than 0.5% at 1kHz (1/3 Rated Power)
>70 dB >70 dB

13.6 ohms (70V), balanced 27.8 ohms (100V), balanced Low impedance: 4-16 ohms, balanced Less than 1V, unbalanced, XLR and phone jack 775V, 0dB, XLR and phone jack 60 - 16,000 Hz, +/- 3dB

15V/uS Volume control and power switch Internal 12VDC fan, extensive heat sinking Power, Clip, Signal, Protect, and Temp LEDs

15V/uS

AC Fuse: 8A AC Fuse: 10A AC FUSE1, Short circuit, high temperature , over voltage protection 520W 110-120V or 220-240V AC, 50/60 Hz 24V DC
89(H) 483(W) 366( D) mm

720W

89(H) x 483(W) x 366(D) mm 2 U rack 19 inch 185(H) x 520(W) x 435(D) mm 18.6kg 20.1kg Panel: steel plate, black Case: steel plate, black

2 U rack 19 inch
185(H) 520(W) 435(D) mm

15.6kg 17.1kg Panel: steel plate, black Case: steel plate, black

Additional features than normal amp:

Speaker output short circuit protection

15

AP SERIES

Amplifier/Speaker Connections

LOW IMPEDANCE (CONSTANT IMPEDANCE) - 4-16 OHMS

SINGLE SPEAKER - SPEAKER LOAD= 8 OHMS
8 SPEAKER

TWO SPEAKERS IN SERIES - SPEAKER LOAD= 16 OHMS

SPEAKER

SPEAKER

SPEAKER

SPEAKER

TWO SPEAKERS IN PARALLEL - SPEAKER LOAD= 4 OHMS

SPEAKER

SPEAKER

SPEAKER

SPEAKER

FOUR SPEAKERS IN SERIES/PARALLEL - SPEAKER LOAD= 8 OHMS

HIGH IMPEDANCE (CONSTANT VOLTAGE) 70/100V

70V SPEAKER 70V SPEAKER

70V - SPEAKER LOAD= 80% AMPLIFIER Rated Power

100V SPEAKER

100V SPEAKER

100V - SPEAKER LOAD= 80% AMPLIFIER Rated Power

16

AP SERIES

Monitor Panel

Emergency Panel

AP-812M
10-CHANNEL MONITOR PANEL
Monitor up to 10 speaker channels audibly by using the built-in loudspeaker. 5-LED dB level meter visually indicates the channels signal level

AP-815E
EMERGENCY PANEL
Outputs siren or user-recorded announcement automatically or manually in the event of an emergency. With the built-in 60second digital IC, it can record and playback a voice message or alarm sound
Playback either built-in siren or pre-recorded message Triggered by external signal or manual pushbutton MIC and LINE inputs for recording messages Audio output for amplifier or other PA equipment

Built-in high fidelity loudspeaker 5-element LED signal level meter Monitor volume control 10-position channel selector switch

REAR PANEL

REAR PANEL

AP-812M
ZONE 1

AP-815E

SPEAKER SELECTOR

AP-813D
RECORDING MIC

MIXER PRE-AMPLIFIER

AP-811P

POWER AMPLIFIER

AP-8660 POWER AMPLIFIER ZONE 10 AP-8660

SPECIFICATIONS
Input Monitored Channels Audible Monitor Visual Monitor Controls Indicators Protection Power Consumption Power Requirements Dimensions Built-in Dimensions Net Weight Gross Weight Finish

AP-812M
70/100V audio signal 10 Full-range loudspeaker, 500mW 6-element LED display, infinite, 0, 2, 4, 6, 8, 10 dB Monitor volume, channel select and power switch Power LED AC Fuse: 0.5A 10-15 watts 110-120V or 220-240V AC, 50/60 Hz; 24VDC 89(H) x 483(W) x 366(D) mm 2 U rack 19 inch 6.1kg 7.88kg Panel: steel plate, black Case: steel plate, black

SPECIFICATIONS
Input Output Frequency Response THD ADC/DAC Controls Protection Power Consumption Power Requirements Dimensions Built-in Dimensions Net Weight Gross Weight Finish

AP-815E
MIC: <5mV, 600 ohms; LINE: <400mV, 10k ohms >200mV, siren or pre-recorded voice message 100 Hz - 3.4kHz, +/- 3dB Less than 0.01% at 1kHz Sampling frequency: 8kHz, 5-bit; 60 seconds Play/rec controls, volume, rec level and power AC Fuse: 0.5A 10-15 watts 110-120V or 220-240V AC, 50/60 Hz; 24VDC 89(H) x 483(W) x 382(D) mm 2 U rack 19 inch 6.1kg 7.78kg Panel: steel plate, black Case: steel plate, black

17

AP SERIES

16-Zone AP Speaker Selectors

16-ZONE SPEAKER SELECTOR
Flexible multi-input speaker selector arranged in a 4 x 4 matrix with priority override. 16 speaker zones are divided into 4 groups, each group can have a separate audio source. A priority bus is provided to mute background music for zone paging and emergency alarms

2 x 5-Zone

10-Zone Speaker Selector

AP-813A

SPECIFICATIONS

AP-813A
4 program and 1 priority channels, 70/100V audio signal 4 groups of 4 zones, 70/100V audio signal 16 channels, activated by 0V signal 1.5kW total capacity, 375W per channel 0V signal 16 pushbutton zone selectors, 1 power switch 110-120V or 220-240V AC, 50/60 Hz; 24VDC 89(H) x 483(W) x 366(D) mm

16-channel priority bus Support for up to 4 audio sources

Input Speaker Output Priority Bus Power Handling Alarm Output Controls Power Requirements

REAR PANEL

Dimensions

2 X 5-ZONE SPEAKER SELECTOR

With 2 amplifier inputs and 2 groups of speaker outputs, the AP-813B can be used as two 5-zone speaker selectors with separate audio sources or as a 10-zone selector with a single audio source

AP-813B

Use as two 5-zone selectors or as one 10-zone selector Supports up to two audio sources

SPECIFICATIONS
Input Speaker Output Priority Bus Power Handling Alarm Output Controls

AP-813B
2 program channels, 70/100V audio signal 2 groups of 5 zones, 70/100V audio signal N/A 1.5kW total capacity, 150W per zone N/A 10 pushbutton zone selectors, 1 power switch 110-120V or 220-240V AC, 50/60 Hz; 24VDC 89(H) x 483(W) x 366(D) mm

REAR PANEL

Power Requirements Dimensions

10-ZONE SPEAKER SELECTOR

The AP-813D is an essential component for a public address system. It has two amplifier inputs (A and B) and controls up to ten speaker zones. It has the ability to select zones when receiving an alarm signal to switch from Input A (background music signal) to Input B (alarm sound signal) to the corresponding zones automatically

AP-813D

SPECIFICATIONS
Input Speaker Output Priority Bus

AP-813D
1 program and 1 priority channels, 70/100V audio signal 1 group of 10 zones, 70/100V audio signal 10 channels, activated by 0V signal 1.5kW total capacity, 150W per zone 0V signal 10 pushbutton zone selectors, 1 power switch 110-120V or 220-240V AC, 50/60 Hz; 24VDC 89(H) x 483(W) x 366(D) mm

10-channel priority bus 2 alarm activation outputs

Power Handling Alarm Output Controls Power Requirements Dimensions

REAR PANEL

18

AP SERIES

AP-813A
PROGRAM
CD PLAYER AP-CD12

AP-813B

AP-813D Examples AP-813A

ZONES 1-4 ZONES 5-8

MIXER AMPLIFIER MIC 1

AP-70M

AM/FM TUNER

AP-F508R

MIXER AMPLIFIER AP-130M MIC 1 CASSETTE DECK AP-W228K

A B C D E PRIORITY
POWER AMPLIFIER

AP-813A

MIXER AMPLIFIER AP-260M MIC 1 CD PLAYER AP-CD12

AP-8660

EMERGENCY PANEL MIXER AMPLIFIER AP-360M MIC 1

AP-815E

ZONES 9-12

ZONES 13-16

AP-813B
PROGRAM A
CD PLAYER AP-CD12 MONITOR PANEL AP-812M

ZONES 1-5

ZONES 6-10

MIXER AMPLIFIER MIC 1

AP-130M

AP-813B
PROGRAM B
AM/FM TUNER AP-F508R

A B

MIXER AMPLIFIER MIC 1

AP-360M

PROGRAM
AM/FM TUNER CASSETTE DECK AP-F508R AP-W228K

AP-813D

ZONE 1
MIXER PRE-AMPLIFIER AP-811P MIC 1 POWER AMPLIFIER AP-8460 MONITOR PANEL AP-812M

ZONE 10

AP-813D
A PRIORITY
POWER AMPLIFIER AP-8660

EMERGENCY PANEL AP-815E

19