0% found this document useful (0 votes)
2K views4 pages

MAX232

The document discusses the MAX232 chip, which is used to convert TTL/CMOS logic levels to RS-232 voltage levels and vice versa. It allows microcontrollers to communicate with devices that use the RS-232 serial communication standard. The MAX232 generates the necessary ±10V voltages from a single 5V supply to interface with RS-232. Asynchronous serial communication transfers data one byte at a time, framing each byte with a start and stop bit.

Uploaded by

janakiram473
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
2K views4 pages

MAX232

The document discusses the MAX232 chip, which is used to convert TTL/CMOS logic levels to RS-232 voltage levels and vice versa. It allows microcontrollers to communicate with devices that use the RS-232 serial communication standard. The MAX232 generates the necessary ±10V voltages from a single 5V supply to interface with RS-232. Asynchronous serial communication transfers data one byte at a time, framing each byte with a start and stop bit.

Uploaded by

janakiram473
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

MAX 232

RS-232 WAVEFORM

TTL/CMOS Serial Logic Waveform The diagram above shows the expected waveform from the UART when using the common 8N1 format. 8N1 signifies 8 Data bits, No Parity and 1 Stop Bit. The RS-232 line, when idle is in the Mark State (Logic 1). A transmission starts with a start bit which is (Logic 0). Then each bit is sent down the line, one at a time. The LSB (Least Significant Bit) is sent first. A Stop Bit (Logic 1) is then appended to the signal to make up the transmission. The data sent using this method, is said to be framed. That is the data is framed between a Start and Stop Bit. RS-232 Voltage levels +3 to +25 volts to signify a "Space" (Logic 0) -3 to -25 volts for a "Mark" (logic 1). Any voltage in between these regions (i.e. between +3 and -3 Volts) is undefined. The data byte is always transmitted least-significant-bit first.

The bits are transmitted at specific time intervals determined by the baud rate of the serial signal. This is the signal present on the RS-232 Port of your computer, shown below.

RS-232 Logic Waveform

2.3.2 RS-232 LEVEL CONVERTER


Standard serial interfacing of microcontroller (TTL) with PC or any RS232C Standard device , requires TTL to RS232 Level converter . A MAX232 is used for this purpose. It provides 2-channel RS232C port and requires external 10uF capacitors. The driver requires a single supply of +5V.

MAX-232 includes a Charge Pump, which generates +10V and -10V from a single 5v supply. Serial communication When a processor communicates with the outside world, it provides data in byte sized chunks. Computers transfer data in two ways: parallel and serial. In parallel data transfers, often

more lines are used to transfer data to a device and 8 bit data path is expensive. The serial communication transfer uses only a single data line instead of the 8 bit data line of parallel communication which makes the data transfer not only cheaper but also makes it possible for two computers located in two different cities to communicate over telephone. Serial data communication uses two methods, asynchronous and synchronous. The synchronous method transfers data at a time while the asynchronous transfers a single byte at a time. There are some special IC chips made by many manufacturers for data communications. These chips are commonly referred to as UART (universal asynchronous receiver-transmitter) and USART (universal synchronous asynchronous receiver transmitter). The AT89C51 chip has a built in UART. In asynchronous method, each character is placed between start and stop bits. This is called framing. In data framing of asynchronous communications, the data, such as ASCII characters, are packed in between a start and stop bit. We have a total of 10 bits for a character: 8 bits for the ASCII code and 1 bit each for the start and stop bits. The rate of serial data transfer communication is stated in bps or it can be called as baud rate. To allow the compatibility among data communication equipment made by various manufacturers, and interfacing standard called RS232 was set by the Electronics industries Association in 1960. Today RS232 is the most widely used I/O interfacing standard. This standard is used in PCs and numerous types of equipment. However, since the standard was set long before the advent of the TTL logic family, its input and output voltage levels are not TTL compatible. In RS232, a 1 bit is represented by -3 to -25V, while a 0 bit is represented +3 to +25 V, making -3 to +3 undefined. For this reason, to connect any RS232 to a microcontroller system we must use voltage converters such as MAX232 to connect the TTL logic levels to RS232 voltage levels and vice versa. MAX232 ICs are commonly referred to as line drivers.

The RS232 cables are generally referred to as DB-9 connector. In labeling, DB-9P refers to the plug connector (male) and DB-9S is for the socket connector (female). The simplest connection between a PC and microcontroller requires a minimum of three pin, TXD, RXD, and ground. Many of the pins of the RS232 connector are used for handshaking signals. They are bypassed since they are not supported by the UART chip.

IBM PC/ compatible computers based on x86(8086, 80286, 386, 486 and Pentium) microprocessors normally have two COM ports. Both COM ports have RS232 type connectors. Many PCs use one each of the DB-25 and DB-9 RS232 connectors. The COM ports are designated as COM1 and COM2. We can connect the serial port to the COM 2 port of a PC for serial communication experiments. We use a DB9 connector in our arrangement.

You might also like