KINNEY

ROTARY PISTON VACUUM PUMPS AND SYSTEMS

KINNEY

CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 KT Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 KT-LP Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 KD/KDH Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 KC Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 KTC Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Options and Accessories . . . . . . . . . .Back Page Flap

PROFILE OF OUR CAPABILITIES

Two years after it was founded in 1902, Kinney introduced the world's first rotary pump. Then in 1926, Kinney developed a vacuum pump for use in large commercial operations. Just as these pumps helped change the face of America by making it possible to mass produce products such as light bulbs, radio tubes, refrigerator and air conditioner components, constant research and innovative manufacturing techniques has continued to spearhead Kinney's leadership in the design and manufacture of oil-sealed rotary piston vacuum pumps. And today, the remarkable long life and reliability of Kinney pumps is testimony to the soundness of the basic rotary piston principle with the elimination of metal-to-metal contact in the pumping chamber. The Kinney line of oil-sealed piston pumps covers a wide range of sizes in both single stage and compound pump design and as part of Tuthill Vacuum & Blower Systems, our full line capability lets us service a host of major industries worldwide (see Application chart on pages 4-5). Our wide selection offers Kinney customers a highly reliable, single source for pumps as well as their installation, service and technical know-how. You can rely on the Kinney line!

KINNEY INTRODUCTION 1

PRINCIPLES OF OPERATION

The Efficiency and Long-Term Reliability of the Kinney Rotary Piston Pump is the Result of the Time-Tested Design. 1. The rotary piston does not spin on its axis. It moves in a circular path within the pumping chamber. 2. As it passes top dead center, it creates a constantly increasing internal space on the inlet or suction side. 3. ...and a constantly decreasing internal space on the pressure or discharge side. 4. A high-integrity seal is maintained between the suction and pressure sides by a film of oil that is captured between the piston and the cylinder. 5. There is no contact between the piston and the cylinder. 6. The oil film is maintained by oil dragged into the clearance by the moving piston which creates a hydrodynamic wedge. 7. At the end of compression cycle, the clearance volume is completely filled with oil, making very high compression ratios available.

These three facts, the oil seal, the filling of the clearance volume, and no contact between piston and wall, are what give the rotary piston pump its low blank off, high pumping speeds at low pressures and great durability.

SINGLE-STAGE OR TWO-STAGE PUMPS

Depending on your application and what vacuum level you need to attain, Kinney Pumps are available in either single-stage or two-stage design. The twostage pumps will achieve a lower vacuum level due to the two piston chambers which are arranged in series with a connecting channel.

Single-Stage

Two-Stage

KINNEY 2 APPLICATIONS

Kinney oil-sealed vacuum pumps are widely accepted as the standard equipment for applications requiring vacuum over a wide pressure range. In research and engineering laboratories, Kinney pumps provide the versatility so essential to technological progress. In production facilities, their ruggedness and compact design permit years of continuous and dependable use. For the electric power industry, Kinney produces complete vacuum systems, both stationary and portable, air cooled and water cooled, for the evacuation, drying and filling of large transformers, for cable filling, drying and impregnation, and for power station condenser evacuation.

Shown here are a few of the many applications of Kinney vacuum pumps. Aerospace and Aviation Evacuation of environmental chambers and test apparatus. Vacuum coating and brazing. Evacuation of cryogenic equipment and vessels. Agriculture Vegetable cooling, produce and berry chilling, grain drying, fumigation, tobacco curing, maple syrup gathering. Air Conditioning and Refrigeration Kinney offers high vacuum pumps specifically modified for servicing refrigeration equipment including thorough vacuum drying, degassing and fast leak detection. Of special importance to manufacturers of air conditioning and refrigeration equipment is Kinney's wide range of experience in the custom design and manufacture of vacuum pumping carts for production line evacuation and drying of systems and components. Automotive Vacuum forming and veneering of interiors, decorative and protective coatings, vacuum filling of cooling and hydraulic systems, lamp production, air conditioning system evacuation, vacuum chucking and lifting, carburetor testing, battery drying, component leak testing, mirror coating. Biologicals and Drugs Freeze-drying, distillation and filtration of biologicals, drugs, vitamins and blood plasma. Chemical Processing Vacuum dehydration, deaeration, purification, distillation and synthesizing. Vacuum evaporation, drying, concentration, deodorizing and filtration.

KINNEY APPLICATIONS 3

Electrical & Electronic Evacuation of incandescent bulbs, fluorescent, neon, electron and TV tubes, potting of electronic components, production of transistors and other semi-conductor devices. Vacuum coating, crystal growing and impregnation. Food Processing Vacuum sealing of bottles, cans and jars, film packaging of meats, poultry and cold cuts, deaeration of beverages, freeze drying of coffee, fruits, vegetables and other food products, vacuum evisceration. Laboratories House vacuum systems, chamber evacuation, research and development. Lasers Laser cooling and atmosphere control. Metallurgy Vacuum degassing, purification, melting, sintering, heat treating, welding, brazing, annealing and impregnation. Nucleonics Evacuation of nuclear reactors, accelerators, cyclotrons and bubble chambers. Paper Decorative and plastic coating, metallizing. Petroleum and Petrochemicals Vacuum distillation and refining, crude yield improvement, oil well evacuation, water deaeration for oil field flooding. Plastics Vacuum forming, molding and coating of plastic materials. Textiles Vacuum drying, dying, material handling and solvent extraction. Miscellaneous Water desalinization. Evacuation of chambers used in precision balancing of high-speed rotary components. Freeze drying of museum specimens. Vacuum coating of reflective architectural glass. Evacuation of shock tubes and wind tunnels. Specimen preparation and replication for electron microscopy. Vacuum coating of optical lenses. Evacuation of ballistic ranges.

KINNEY 4 KT SERIES

SINGLE-STAGE ROTARY PISTON VACUUM PUMPS

KT-150, KT-300, KT-500, KT-850

HIGHLIGHTS Fuel Pumping Speed Down to 1 Torr Operate Continuously at any Pressure up to 100 Torr Ultimate Pressure 10 Microns (McLeod Gauge) Quiet, Vibration-Free Operation Simple Installation. No Special Preparation Necessary No Metal-to-Metal Contact in Pumping Chamber Adjustable Gas Ballast Permits Handling of Condensable Vapors Unequalled Durability Even in Dirty Applications Typical Applications: Vacuum Packaging, Vacuum Furnaces, Vacuum Coating
SPECIFICATIONS

MODEL
Nominal Displacement at Rated RPM Motor HP Oil Capacity Cooling Water (min) @ 60F (16C) @45PSI (max) Weight (Complete Pump Assy) Dry Maximum Gas Ballast Flow Typical Blank-off Pressure with 5% GB Ultimate Pressure (McLeod Gauge) Typical Noise Level @ 10 Torr cfm/m3/hr hp/kw gal/ltr gpm/lpm lbs/kg

KT-150
150/255 7.5/6 6/23 1/4 800/364 10% 2.0/3.0 0.010/0.013 71

KT-300
300/505 15/11 10/38 2/6 1525/693 5% 2.0/3.0 0.010/0.013 72

KT-500
490/840 30/22 15/57 3/9 2700/1225 5% 2.0/3.0 0.010/0.013 73

KT-850
780/1325 40/30 28/106 4/13 4400/1996 5% 2.0/3.0 0.010/0.013 75

Torr/mbar Torr/mbar dBA

All specifications and dimensions subject to change without notice.

PLUS FEATURES
TRIPLEX DESIGN MEANS VIRTUALLY VIBRATION-FREE OPERATION

Kinney KT Pumps have three sets of cams and pistons driven by a common shaft. One cam and piston set is no longer than the other two and the cams are set 180 apart. The dynamic forces produced by the rotation of the long cam and piston are balanced by opposing forces produced by the short cams and pistons on either side. The resulting out-of-balance force is very small, making it possible to mount the pump on springs or vibramounts which substantially reduce the dynamic forces transmitted to the floor. See back page flap for Options and Accessories

HIGH PRESSURE OIL PUMPS ASSURE PROPER LUBRICATIONS

Pumps are lubricated by forced oil feed at all pressures. This forced feed ensures constant oil flow even at high suction pressures.

NO ANCHOR BOLTS

KT Pumps do not require lagging, anchor bolts or special foundations and may be located on any floor that will support their weight.

KINNEY

KT SERIES 5
DIMENSIONS KT-150, KT-300, KT-500, KT-850
K P WATER INLET FAR SIDE NPT

R WATER OUTLET FAR SIDE NPT GAS BALLAST VALVE ASSEMBLY B

OIL FILL G DISCHARGE FLANGE

N SUCTION FLANGE J

C L ROTATION VIEW PLUG M F

D A

(4) VIBRATION MOUNTS

DIMENSIONS (Inches/Millimeters)
MODEL KT-150C KT-300D KT-500D KT-850D A 26.00 660 33.50 851 37.25 946 48.50 1232 B 43.00 1092 51.25 1302 63.13 1604 69.50 1765 C 8.63 219 11.00 267 11.75 298 13.38 340 D 11.75 298 15.00 381 17.00 432 24.75 629 E 12 .63 321 16.00 406 21.50 546 24.25 616 F 14.50 368 18.50 470 21.25 540 25.75 654 G 2" ANSI 3" ANSI 4" ANSI 5" ANSI J 26 .50 673 32.50 826 41.00 1041 46.00 1168 K 22.75 578 23.19 589 32.32 821 37.25 946 L 19 .13 486 22.50 572 28.00 711 33.00 838 M 1.19 30 1.69 43 1.31 33 1.38 29 N 3" ANSI 4" ANSI 6" ANSI 8" ANSI P 1/4 3/8 3/8 3/8 Q 9.38 238 12.38 314 15.38 391 18.25 464 R 3/8 1/2 1/2 1/2

The above table is not for construction purposes. Consult TVBS for certified drawings.
PERFORMANCE CURVES
PUMPING SPEED IN CUBIC MEETERS PER HOUR PUMPING SPEED IN CUBIC MEETERS PER HOUR PUMPING SPEED IN CUBIC MEETERS PER HOUR TYPICAL PUMPING SPEED CUR MODEL KT-150 150 255 TYPICAL PUMPING SPEED CUR MODEL KT-300 300 504.8 424.8
ATOMOSPHERE

PUMPING SPEED IN CFM

PUMPING SPEED IN CFM

120
ATOMOSPHERE

204

250 200 150 100 50 0 .001

339.8 254.9 169.9 85.0

90

153

60

102

30

51

0 .001

.005 010

050 100

.500 1

5 10 29.5

50 100

PRESSURE IN TORR (MB MM HG ABS)

28 26 VACUUM IN HG

0 500 1000 20 0

.005 010

050 100

.500 1

5 10 29.5

50 100

PRESSURE IN TORR (MB MM HG ABS)

28 26 VACUUM IN HG

0 500 1000 20 0

500

850

PUMPING SPEED IN CUBIC MEETERS PER HOUR

TYPICAL PUMPING SPEED CUR MODEL KT-500

TYPICAL PUMPING SPEED CUR MODEL KT-850 800 700 PUMPING SPEED IN CFM
ATOMOSPHERE

1360 1190 1020 850 680 510 340 170 0 500 1000 20 0

PUMPING SPEED IN CFM

400
ATOMOSPHERE

680

600 500 400 300 200 100 0 .001

300

510

200

340

100

170

0 .001

.005 010

050 100

.500 1

5 10 29.5

50 100 28 20

PRESSURE IN TORR (MB MM HG ABS)

0 500 1000 0

.005 010

050 100

.500 1

5 10 29.5

50 100

26 VACUUM IN HG

PRESSURE IN TORR (MB MM HG ABS)

28 26 VACUUM IN HG

KINNEY 6 KTLP SERIES

OIL-SEALED ROTARY PISTON PUMPS

KT-170 LP, KT-275 LP, KT-505 LP, KT-840VFP, KT-1350VFP

HIGHLIGHTS Quiet, Vibration Free No Metal-to-Metal Contact Ultimate Pressure to 10 microns Full Pumping Speed Down to 1 Torr Compact Design, Easy Access for Maintenance Simple Installation

Typical Applications: Vacuum Packaging, Vacuum Furnaces, Vacuum Coating

SPECIFICATIONS

MODEL
Nominal Displacement at Rated RPM Motor HP Normal Pump Rotation Oil Capacity Cooling Water (min) @ 60F (16C) @45PSI (max) Weight (Complete Pump Assy) Dry Maximum Gas Ballast Flow Typical Blank-off Pressure with 5% GB Ultimate Pressure (McLeod Gauge) Typical Noise Level @ 10 Torr cfm/m3/hr hp/kw rpm gal/ltr gpm/lpm lbs/kg

KT-170 LP
100/170 5/3.7 1150 2.6/10 1/4 750/340 10% 2.0/3.0 0.010/0.013 71

KT-275 LP
162/275 10/7.5 1200 4.5/17 1/4 900/408 10% 2.0/3.0 0.010/0.013 72

KT-505 LP
300/505 15/11 870 10/38 2/6 1870/848 5% 2.0/3.0 0.010/0.013 72

KT-840 VFP
490/840 30/22 744 15/57 3/9 3650/1660 5% 2.0/3.0 0.010/0.013 73

KT-1350 VFP
780/1325 40/30 581 28/106 4/13 4375/1959 5% 2.0/3.0 0.010/0.013 75

Torr/mbar Torr/mbar dBA

All specifications and dimensions subject to change without notice.

PLUS FEATURES
TRIPLEX DESIGN MEANS VIRTUALLY VIBRATION-FREE OPERATION

Kinney KT Pumps have three sets of cams and pistons driven by a common shaft. One cam and piston set is no longer than the other two and the cams are set 180 apart. The dynamic forces produced by the rotation of the long cam and piston are balanced by opposing forces produced by the short cams and pistons on either side. The resulting out-of-balance force is very small, making it possible to mount the pump on springs or vibramounts which substantially reduce the dynamic forces transmitted to the floor. See back page flap for Options and Accessories

HIGH PRESSURE OIL PUMPS ASSURE PROPER LUBRICATIONS

Pumps are lubricated by forced oil feed at all pressures. This forced feed ensures constant oil flow even at high suction pressures.

NO ANCHOR BOLTS

KT Pumps do not require lagging, anchor bolts or special foundations and may be located on any floor that will support their weight.

KINNEY KTLP SERIES 7

DIMENSIONS KT-170 LP, KT-275 LP, KT-505 LP PERFORMANCE CURVES

TYPICAL PUMPING SPEED CURVE MODEL KT-505LP, KT-840VFP and KT1350VFP mBar

KT-1350VFP

1300 1200 1100 1000 900

700 PUMPING SPEED IN CFM 600 500 400 300 200 100

NEW

KT-840VFP 800
700 600

KT-505LP 500
400 300 200 100

KT-840 VFP, KT-1350 VFP

0 0.001

0.010 0.100 1 10 100 SUCTION PRESSURE, TORR MB

1000

TYPICAL PUMPING SPEED CURVE MODEL KT-170LP, KT-275LP

KT-275LP

250

140 PUMPING SPEED IN CFM 120 100 80 60 40 50 20 100 200

KT-170LP

150

DIMENSIONS (Inches/Millimeters)

MODEL
KT-170LP

B
24.63 626 25.5 648 33.88 861 67 1702 77.75 1975

C
Inlet

D
Discharge

F
21 533 21.75 552 28.25 699 61.25 1556 68.75 1746

G
37.25 946 40.5 1029 48.50 1232 33 838 39.38 1000

H
36.19 919 35 889 44.25 1124 15.38 391 18.25 464

J
0 0.001 0.010 0.100 1 10 100

0 1000 SUCTION PRESSURE, TORR MB

24.75 629 KT-275LP 28 711 KT-505LP 35.25 895 KT-840VFP 50 1270 KT-1350VFP 59 1499

3" 2" 13 NPT NPT 330 3" 2" 13.75 ANSI NPT 349 4" 3" NPT/ 16.75 ANSI 3" ANSI 425 6" 4" 21 ANSI ANSI 533 8" 5" 24.25 ANSI ANSI 616

28.50 724 32.13 816

STRONGER 4-PIECE CAGED SLIDE PINS

Slide pins in all Kinney Rotary Piston Pumps have 4-pieced caged construction, with end pieces that keep both segments in perfect alignment.

INTEGRAL OIL-MIST-ELIMINATOR CONVERSES OIL, PROVIDES CLEAN DISCHARGE

All Kinney KT Series Low Profile Pumps have as standard an integral three-stage oil-mist-eliminator, which captures and returns the oil to the oil reservoir. The first stage is an impingement umbrella on which the largest oil droplets are removed. The second stage is a stainless steel pad, which collects small droplets. The third and final stage is a coalescing filter of glass fibers which removes all visible oil smoke from the discharge gas. Oil collected from all three stages automatically drains back to the oil reservoir.

PUMPING SPEED IN CUBIC METERS PER HOUR

160

PUMPING SPEED IN CUBIC METERS PER HOUR

800

KINNEY 8 KD/KDH SERIES

OIL-SEALED SINGLE-STAGE ROTARY PISTON VACUUM PUMPS

KD-30, KD-50, KDH-130, KDH-150

HIGHLIGHTS Can Operate at any Pressure up to Atmosphere Absolute Pressure Down to the Low Micron Range. Ultimate Pressure of 10 Microns HG ABS or Less (McLeod Gauge) High Resistance to Abrasion and Corrosion No Small Orifices to Plug Up Adjustable Gas Ballast Permits Handling of Condensable Vapors Typical Applications: Drying Chambers, Degassifiers, Filling Machines, Evacuating Process Chambers Models KD and KDH are single stage vacuum pumps of "duplex" design. Each has a single shaft with two sets of cams and pistons mounted 180 apart, which operate in parallel. The rotary pistons do not touch the walls of the pumping chambers but are sealed by oil, which acts as both a lubricant and a sealant. KD pumps are air-cooled; KDH pumps need water cooling for most applications.
SPECIFICATIONS

These are other quality features: a controllable gas ballast to permit the handling of condensable vapors and to minimize oil changes due to vapor contamination of the sealing oil. Models KD-30 and KD-50 are equipped with an oil mist eliminator, optional on model KDH-130 & KDH-150. Each pump operates within the rating of its standard TEFC motor throughout the entire operating pressure range.

MODEL
Nominal Displacement at Rated RPM Motor HP Normal Pump Rotation Oil Capacity Cooling Water (min) @ 60F (16C) Weight (Complete Pump Assy) Dry Maximum Gas Ballast Flow Typical Blank-off Pressure with 5% GB Ultimate Pressure (McLeod Gauge) Typical Noise Level @ 10 Torr Torr/mbar Torr/mbar dBA cfm/m3/hr hp/kw rpm gal/ltr gpm/lpm lbs/kg

KD-30
33/56 1.5/1 571 1/3.8 AC 200/91 8% 1.5/2 0.010/0.013 75

KD-50
52/88 2/1.5 900 3/11.4 AC 230/104 6% 1.5/2 0.010/0.013 80

KDH-130
134/227 5/3.7 546 6/22.7 .75/3 755/331 6% 1/1.3 0.010/0.013 70

KDH-150
165/280 7.5/5.6 685 6/22.7 .75/3 840/381 6% 1/1.3 0.010/0.013 72

All specifications and dimensions subject to change without notice.

PLUS FEATURES
HIGH VAPOR HANDLING

Kinney Piston Pumps are equipped with three features to handle high vapor loads. First, the adjustable gas ballast valve can introduce air to the pumping chamber, which helps prevent vapor from condensing in the pump oil. Second, Piston Pumps have a large oil capacity, which has a higher tolerance to contamination. The large reservoir can collect a significant volume of condensed liquid, which can be drained from the pump. Third, Piston Pumps can operate as part of a vapor handling system, in which the oil reservoir is maintained under vacuum. This is made possible by the oil pump and the design of the oil reservoir to operate under vacuum. Vapor handling systems, which keep the oil dry, can operate in corrosive applications.

STRONGER 4-PIECE CAGED SLIDE PINS

Slide pins in all Kinney Rotary Piston Pumps have 4-pieced caged construction, with end pieces that keep both segments in perfect alignment.

See back page flap for Options and Accessories

KINNEY KD/KDH SERIES 9

DIMENSIONS KD-30, KD-50
F A NPT DISCHARGE 1/2" NPT OIL FILL (1 GALLON OIL CAPACITY) SEPARATOR TANK WITH FILTER ELEMENT & OIL RESERVE VIEW PORT SOLENOID VALVE 1 1/2" NPT SUCTION DRAIN VALVES D BELT GUARD

GAS BALLAST VALVE

7/16 DIA. HOLES

NPT DISCHARGE

KDH-130, KDH-150
F 3" 150# ASA FLANGE B NPT DRAIN VALVE GAS BALLAST VALVE 3/4

OIL SIGHT GUAGE 1/2" NPT OIL FILL

NPT WATER OUTLET

SOLENOID VALVE

NPT WATER INLET BELT GUARD E C A

DIMENSIONS (Inches/Millimeters)

MODEL
KD-30 KD-50 KDH-130, KDH-150

A
27 7/8 518 28 5/8 727 38 7/8 987

B
27 686 32 1/2 826 39 1/4 997

C
24 1/2 432 24 1/2 622 33 5/8 854

D
12 7/8 327 12 7/8 327 20 508

E
17 3/8 400 17 3/8 441 30 13/16 783

F
20 508 20 508 28 5/16 719

PERFORMANCE CURVES
TYPICAL PUMPING SPEED CURVE MODEL KD-30 and KD-50 TYPICAL PUMPING SPEED CURVE MODEL KDH-130 and KDH-150 PUMPING SPEED IN CUBIC MEETERS PER HOUR PUMPING SPEED IN CUBIC MEETERS PER HOUR 85 150 255

50

KD-50

KDH-150
120 PUMPING SPEED IN CFM

40 PUMPING SPEED IN CFM

ATOMOSPHERE

68

KDH-130
ATOMOSPHERE

204

30

KD-30

51

90

153

20

34

60

102

10

17

30

51

0 .001

.005 010

050 100

.500 1

5 10 29.5

50 100

PRESSURE IN TORR (MB MM HG ABS)

28 26 VACUUM IN HG

0 500 1000 20 0

0 .001

.005 010

050 100

.500 1

5 10 29.5

50 100 28 20

PRESSURE IN TORR (MB MM HG ABS)

0 500 1000 0

26 VACUUM IN HG

KINNEY 10 KC SERIES

OIL SEALED TWO-STAGE ROTARY PISTON VACUUM PUMPS

KC-5, KC-8, KC-15

HIGHLIGHTS Pumping Speed at Pressures Below 10 Microns. Lower than Attainable with Single-Stage Pumps Ultimate Pressure: .2 Microns (McLeod Gauge) Can Operate at Any Pressure up to Atmosphere Adjustable Gas Ballast Permits Handling of Condensable Vapors No Metal-to-Metal Contact in Pumping Chamber Unequaled Durability, Even in Dirty Applications Air-Cooled Typical Applications: Refrigeration Systems, Liquid Gas Storage, Automotive Applications, Leak Detection Kinney Series, two-stage vacuum pumps, are designed to achieve lower pressures than can be achieved with single-stage pumps. Two sets of cams and pistons, mounted 180 apart on a single shaft, operate in series. The two pumping chambers are connected by a channel, which serves as an oil supply duct for the high vacuum side of the pump and as a gas duct between the two stages. The high vacuum side is continuously sealed with vacuum oil from its own reservoir, the vacuum conditioning being provided by the roughing (2nd) stage. Functionally vibrationless, they are well suited for portable installations. Because there is no metal
SPECIFICATIONS

contact between the pump piston and cylinder, clearances are sealed and lubricated with oil. Units are equipped with a gas ballast valve to provide vapor-handling capability. Oil mist eliminators are standard. Each pump operates within the rating of its standard TEFC motor throughout its operating pressure range. Wear is minimum. Units operate without repairs for many years. Pumps can be serviced easily in the field without special tools. Specifically manufactured refrigeration units prepared for use with POE oil, compatible with Freon R134A are also available.

MODEL
Nominal Displacement at Rated RPM Motor HP Normal Pump Rotation Oil Capacity Weight (Complete Pump Assy) Dry Maximum Gas Ballast Flow Typical Blank-off Pressure with 5% GB Ultimate Pressure (McLeod Gauge) Typical Noise Level @ 10 Torr Torr/mbar microns/mbar dBA cfm/m /hr
3

KC-5
5/8.5 .33/.25 638 0.8/.76 115/52 15% 0.020/0.027 0.2/2.7x10-4 75 hp/kw rpm qts/ltr lbs/kg

KC-8
8/13.6 .5/.38 1022 0.8/.76 120/54 15% 0.020/0.027 0.2/2.7x10-4 78

KC-15
15/25.5 1/.75 571 3/2.8 210/95 15% 0.020/0.027 0.2/2.7x10-4 75

All specifications and dimensions subject to change without notice.

SPECIAL SERVICE PUMPS

Kinney KC series pumps are ideally suited for tough, demanding applications. They can also be ordered for specific, special duty applications. Refrigeration Service Pumps these pumps are manufactured and tested using oil and seals which are compatible with the Freon used in refrigeration coils and compressors. See back page flap for Options and Accessories Automotive Brake Line Filling Pumps these pumps are manufactured and tested using oil which is compatible with brake fluid. A special shaft seal design eliminates oil leakage due to brake fluid contamination in the pump. Industrial Gas Distribution these pumps are manufactured and tested using oil which is fire resistant.

KINNEY 1 KC SERIES 1
DIMENSIONS KC-5, KC-8, KC-15

M N R OIL FILL PLUG S P U T NPT DISCHARGE GAS BALLAST VALVE BELT GUARD A V W X

Z NPT SUCTION

B
KINNEY

H F Y OIL DRAIN VALVES L G

D C

DIMENSIONS (Inches/Millimeters)

MODEL
KC-5 KC-8 KC-15

A
18.00 457 18.00 457 20.25 514

B
17.88 454 17.88 454 24.31 617

C
16.50 419 16.50 419 17.00 432

D
4.57 116 4.57 116 4.00 101

E
8.00 203 8.00 203 9.00 229

F
5.06 129 5.06 129 6.00 152

G
4.50 114 4.50 114 5.50 140

H
(9.88) 251 (9.88) 251 (10.00) 254

J
9.69 246 9.69 246 12.81 325

K
4.38 111 4.38 111 8.00 203

L
9.75 248 9.75 248 15.75 400

M
14.13 359 14.13 359 17.94 456

N
4.38 111 4.38 111 7.25 184

MODEL
KC-5 KC-8 KC-15

P
7.50 191 7.50 191 10.69 272

R
1.50 38 1.50 38 3.00 76

S
1.75 44 1.75 44 3.50 89

T
3/4 " 3/4 " 1 1/2 " -

U
1.00 25 1.00 25 0.56 14

V
7.13 181 7.13 181 7.25 184

W
3.13 80 3.13 80 3.75 95

X
1.19 30 1.19 30 -

Z
1.00 1.00 2.00 -

WT. lbs./kg
115/52 120/54 210/95

PERFORMANCE CURVES
TYPICAL PUMPING SPEED CURVE MODELS KC-5 and KC-8 PUMPING SPEED IN CUBIC MEETERS PER HOUR 7 11.9 14

TYPICAL PUMPING SPEED CURVE MODEL KC-15 PUMPING SPEED IN CUBIC MEETERS PER HOUR 23.8

6 PUMPING SPEED IN CFM

KC-8

10.2

12 PUMPING SPEED IN CFM

KC-15

20.4

8.5

10

17.0

6.8

KC-5
3 5.1

13.6

10.2

3.4

6.8

1.7

3.4

0 0001 .0005 .001 .005 .010 .050 .100 .500 1 5 10 50

0 100

0 0001 .0005 .001 .005 .010 .050 .100 .500 1 5 10 50

0 100

PRESSURE IN TORR (MB MM HG ABS)

PRESSURE IN TORR (MB MM HG ABS)

KINNEY 12 KTC
OIL-SEALED TWO-STAGE ROTARY PISTON VACUUM PUMPS
KTC-21, KTC-60, KTC-112

HIGHLIGHTS Triplex Piston Design for Quiet, Vibration-Free Operation High Pumping Speed at Pressure Below 10 Microns, Lower than Attainable with Single-Stage Pumps Ultimate Pressure: .2 Microns (McLeod Gauge) Can Operate at Any Pressure up to Atmosphere Adjustable Gas Ballast Permits Handling of Condensable Vapors No Metal-to-Metal Contact in Pumping Chambers Unequalled Durability, Even in Dirty Applications Typical Applications: Brake Filling Systems, Low Pressure Chemical Vapor, Silicon Crystal Growing, Air Conditioning
The KTC series two-stage high vacuum pumps are of "triplex" design, a single shaft with three sets of cams and pistons, one set larger than the other. Pumps in this series maintain lower pressures than are attainable with single-stage pumps. In operation, one of the smaller pumping chambers is in series with (backing) the other two, which function in parallel. A unique internal balancing technique reduces the magnitude of pump movement (deflection) to 0.0002'' while simultaneously reducing the dynamic forces transmitted through the flexible mounting pads furnished with each pump to less than one pound. These pumps are vibration-free, air-cooled, (except the KTC-12 which is water-cooled), and equipped with an adjustable gas ballast providing vapor handling capability while reducing oil changes by preventing condensable vapors from contaminating the oil.
SPECIFICATIONS

(Explosion proof option shown)

Other superior quality features include a special umbrella type discharge baffle to reduce oil loss to levels not attainable in other pumps, solenoid valves to protect against oil flooding and the single gas ballast adjustment that assures balanced air flow and simple regulation. The pump operates within the rating of its standard TEFC motor throughout the complete operating pressure range.

MODEL
Nominal Displacement at Rated RPM Motor HP Normal Pump Rotation Oil Capacity Cooling Water (min) @ 60F (16C) Weight (Complete Pump Assy) Dry Maximum Gas Ballast Flow Typical Blank-off Pressure with 5% GB Ultimate Pressure (McLeod Gauge) Typical Noise Level @ 10 Torr cfm/m /hr
3

KTC-21
21/36 1.5/1.1 1725 .5/1.9 AC 170/77 10% 0.020/0.027 0.2/2.7x10-4 72

KTC-60
60/102 3/2.3 972 2/7.5 AC 515/234 10% 0.020/0.027 0.2/2.7x10-4 70

KTC-112
107/182 7.5/5.6 1055 4/15 1.5/5.5 765/347 10% 0.020/0.027 0.2/2.7x10-4 70

hp/kw rpm gal/ltr gpm/lpm lbs/kg Torr/mbar microns/mbar dBA

All specifications and dimensions subject to change without notice.

PLUS FEATURES
TRIPLEX DESIGN MEANS VIRTUALLY VIBRATION-FREE OPERATION

Kinney Piston Pumps have three sets of cams and pistons driven by a common shaft. One cam and piston set is no longer than the other two and the cams are set 180 apart. The dynamic forces produced by the rotation of the long cam and piston are balanced by opposing forces produced by the short cams and pistons on either side. The resulting out-of-balance force is very small, making it possible to mount the pump on springs or vibramounts which substantially reduce the dynamic forces transmitted to the floor. See back page flap for Options and Accessories

NO ANCHOR BOLTS

KT Pumps do not require lagging, anchor bolts or special foundations and may be located on any floor that will support their weight.

KINNEY KTC 13

DIMENSIONS KTC-21
M SUCTION NPT N DISCHARGE NPT K NPT OIL FILL GAS BALLAST VALVE J NPT SUCTION 150# ASA FLANGE XP MTR ONLY B

KTC-60, KTC -112

H F R

SIGHT GLASS

G NPT DISCHARGE (FAR SIDE) GAS BALLAST VALVE OIL FILL OIL FILL P NPT WATER OUTLET N SUCTION FLANGE 150# ASA P NPT WATER INLET

OIL LEVEL VIEW PORT J (2) OIL DRAINS

C H G L

D A L K M

C A

DIMENSIONS (Inches/Millimeters)

MODEL A
KTC-21 KTC-60 KTC-112

C
2 1/2 64 8 3/4 213 9 1/2 241

D
12 3/8 314 10 254 10 254

E
6 1/4 159 19 5/8 498 12 5/8 321

F
5 127 13 3/4 349 14 1/2 368

G
9 9/16 243 1 1/2 NPT 2 FLG

H
7 178 7 5/8 194 9 1/2 241

L
15 5/8 397 11 1/2 292 12 1/4 311

M
2 1/2 64 3 1/8 79

N
1 NPT 3 ANSI 3 ANSI

P
1/4 NPT

R
6 3/16 159 7 178

25 1/8 20 1/8 638 511 23 1/4 36 1/2 591 927 26 43 660 1092

2 3/4 21 3/4 18 3/4 552 476 27 3/8 20 3/4 695 527

PERFORMANCE CURVES TYPICAL PUMPING SPEED CURVE MODELS KTC-112, KTC-60, KTC-21 140 120 PUMPING SPEED IN CFM 100 KTC-112 80 60 KTC-60 40 20 KTC-21 0 0001 .0005 .001 .005 .010 .050 .100 .500 1 5 10 50 100 500 PRESSURE IN TORR (MM HG ABS) 0 1000 50 100 150 200

HIGH VAPOR HANDLING

Kinney KT Pumps are equipped with three features to handle high vapor loads. First, the adjustable gas ballast valve can introduce air to the pumping chamber, which helps prevent vapor from condensing in the pump oil. Second, KT Pumps have a large oil capacity, which has a higher tolerance to contamination. The large reservoir can collect a significant volume of condensed liquid, which can be drained from the pump. Third, KT Pumps can operate as part of a vapor handling system, in which the oil reservoir is maintained under vacuum. This is made possible by the oil pump and the design of the oil reservoir to operate under vacuum. Vapor handling systems, which keep the oil dry, can operate in corrosive applications.

STRONGER 4-PIECE CAGED SLIDE PINS

Slide pins in all Kinney Rotary Piston Pumps have 4-pieced caged construction, with end pieces that keep both segments in perfect alignment.

PUMPING SPEED IN CUBIC MEETERS PER HOUR

Customized Vacuum Pump Systems

All Kinney Piston Pumps can be combined with booster pumps, liquid ring pumps, or in a variety of customized pumping packages.

Please contact us.

KINNEY OPTIONS AND ACCESSORIES

CUSTOMIZED OPTIONS Explosion-proof Motors All Kinney piston pumps can be equipped with any special motor. Special Oils We can manufacture any of our pumps with special, application specific oils. Pumps will be manufactured from scratch with the precise oil to avoid contamination. CUSTOM ACCESSORIES Oil Mist Eliminator 99.95% filtering efficiency Some w/oil storage capacity & built-in check valve Oil Filtration System Self-priming positive displacement pump Welded steel construction Epoxy-coated internals Variety of filtration element options Single or three-stage TEFC motors Air-cooled Heat Exchanger Available for KT & KTC models Bronze circulation pump w/closed-coupled TEFC motor Interconnection hoses Single or three-stage models available Electrical Control Custom engineered control panels
7.5 HP 1L1
20A F1

3PH 60HZ

460V L1 L2 L3
1L1
1 RED
E-STOP

1L2
1A

3Amp F7 3Amp F8

1
1PB

H2 X1

460V

1A

8Amp F9

H1
120V

1T 500VA
WHITE

1
CYCLE STOP SYSTEM 2PB

2 2 3LT POWER ON (E-STOP)

1 3
3

START

F.O. : 905501

1L2

3PB

1L3

G
4 1

4LT SYSTEM 3CR PUMP SHUT DOWN RELAY START

CONTRO

3CR2
4 4

L SEQUEN

4
4

CE:

1S0L
2

3CR1
1
B1 A1 2TR A2

18

VENT VALVE (N.O.) (OPTIONAL)

2TR
15

20A F2

18

2 13

1OL

15A F4

15A F5

(NO CONTACTS)

PUMP SHUT (OFF DELAY OFF TIMER 20 SEC.)

1) BEFORE TURNING ON THE FLOW MUST SYSTEM, BE ESTABLIS COOLING (THE OIL HED AND WATE LEVELS CONFIRM MUST BE THE MANUAL ED. CHECKED ISOLATIO DAILY.) SHOULD BE CLOSED. N VALVE (LOCATED ELSEWHE RE 2) TO START

20A F3

15A F6

(OFF DELAY

2L1

5 Min.)

2L2

14

14

2L3

1M
14

3L1

3L3

1M 2M 1OL 2OL

3L2

MECHANICAL PUMP MOTOR STARTER 1LT PUMP RUN

A
4

OFF & RESET

4

1SS SELECTOR SW. (2POS.) AUTO

1TAS

(NC)
TEMP SW.

21 21

(OPEN

ABOVE

235 Deg.

F)

5CR CONTROL
5

RELAY

1M1

2T1

2T3

5CR1

6CR1

1 MTR
PUMP MOTOR 1800 RPM 460V

2 MTR
BOOSTER MOTOR 5HP 3600 RPM 460V

6CR CONTROL RELAY

2CR1
7

2CR2
12

4LT HIGH TEMP.

1CR2

1CR CONTROL RELAY

1CR4
9

12

2CR 6CR2 2CR4

8 10

CONTROL

RELAY

PRESSURE 1PS

SW.
11

(NO) (CLOSED
6

4CR

BELOW

BOOSTER

30 Torr) (29.4 Hg.)

SHUT DOWN

RELAY

6CR3
20

4CR1
19
B1

THE SYSTEM, SWITCH (SET AT THE BOOSTER "B") MUST BE IN THE WHEN SELECTO "OFF/RES THE START R ET" POSITION BUTTON IS ENERGIZE IS PUSHED, . D AND THE RELAY THE MECHNIC STARTS TO RUN. 3CR AL PUMP THE VENT CLOSED MOTER VALVE WHEN CLOSES THE MOTOR AND STAYS IS RUNNING 3) AFTER . 20 Sec. THE BOOSTER SHOULD BE TURNED SELECTO THE MANUAL TO "AUTO" R SWITCH POSITION ISOLATIO MAY BE . N VALVE OPENED. (LOCATED ELSEWHE RE) 3) WHEN THE VACUUM 30 TORR PRESSUR (mm E DROPS AND STARTS Hg. Abs.), THE DOWN THE BOOSTER PRESSURE SWITCH TO GETS DEPLETED . IF THE CLOSES AND THE VACUUM ABOVE 30 TORR, VACUUM PRESSUR THE PRESSUR E A 30 SECOND BOOSTER E RISES SHUTS DELAY. OFF AFTER WHEN THE VACUUM THE BOOSTER PRESSUR E DROPS STARTS BELOW AGAIN. 30 TORR 4) IF THE EXHAUST TEMPERA 235 Deg. F., THE TURE RISES BOOSTER WHEN ABOVE SHUTS THE BOOSTER DOWN. BY TURNING COOLS THE SELECTO DOWN IT CAN AND THEN BE STARTED R SWITCH TO "AUTO" TO "OFF" POSITION POSITION . 6) TO SHUT DOWN THE SYSTEM, SELECTO R SWITCH THE BOOSTER SHOULD POSITION BE . THEN THE MANUAL TURNED TO SHOULD "OFF/RES BE CLOSED. ISOLATIO ET" N VALVE 5) WHEN THE STOP SHUTS BUTTON OFF AND IS THE MECHANI PUSHED, THE RUN AND BOOSTER THE VENT CAL PUMP (20 Sec.). VALVE CONTINUE OPENS AFTER S TO FOR PURGE THE PURGE THE PUMP CYCLE SHUTS CYCLE IS OVER, DOWN. 6) E-STOP MUST BE PUSHED THE SYSTEM. IN TO SHUT DOWN

1T1

1T2

1T3

2T2

A1 1TR

A2

1TR
15 18

16

6CR4
17

PRESSURE SW. (1PS) STABILITY TIMER (OFF DELAY 30 SEC.)

2OL
15

(NO CONTACTS) (OFF DELAY 30 Sec.)

(SET AT

"B")

15

2M
15 A

BOOSTER MOTOR STARTER 2LT BOOSTER RUN

REF. DWG.

NOTICE

REV. ECN DATE DESCRIPT ION BY

OF CONFIDENTIAL INFORMATION

CHECKED REVIEWED

INFORMATION CONTAINED AND IS THE PROPERTY HEREIN WHERE IS CONFIDENTIAL FURNISHED OF THE SHALL KINNEY WITH A USE IT PROPOSAL VACUUM DIVISION. SOLELY WHERE TO EVALUATE THE SOLELY FURNISHED TO A CUSTOMER THE RECIEPIENT FOR THE OR MAINTAINENCE. PROPOSAL. PURPOSES IT SHALL OF INSPECTION, IT SHALL BE USED BE USED WHERE FURNISHED WORK INSTALLATION, CONTRACTEDSOLELY TO A SUPPLIER IN INFORMATION FOR BY THE PERFORMANCE RECIPIENT THE SHALL OF FOR ANY NOT BE USEDCOMPANY. THE OTHER OR PURPOSE DISCLOSED BY THE WHATSOEVER.

MATL. DRAWN BY DATE

ENCLO
TD

SURE :

NEMA-

6/26/01

BY BY DATE DATE
R

TUTHIL
CORPORAT

WIRING DIAGRAM KMBD540 / KT-150 (PUMP & BOOST ER)

Kinney
Division

4 24X24X
SCALE NEXT ASSY. REV. NO.
1

ION

Vacuum

Canton Massachusetts USA

DWG. NO. 577473

Many more available

LOCATIONS WORLDWIDE Manufacturing & Service

Americas
Tuthill Vacuum & Blower Systems 4840 West Kearney Street Springfield, Missouri USA 65803-2602 Tel (417) 865-8715 (800) 825-6937 Fax (417) 865-2950 http://vacuum.tuthill.com

Europe/Middle East/Africa
Tuthill Vacuum & Blower Systems/Europe Pennine Business Park, Pilsworth Road Heywood, Lancashire, 0L10 2TL, England Tel (44) 01706 362 400 Fax (44) 01706 362 444

Asia/Pacific
Shanghai Kinney Vacuum Equipment Co. Ltd. 3516 Wai Qing Song Highway Shanghai, China 201709 Tel 86-21-5974 5418 Fax 86-21-5974 4905

International Sales Offices

Tuthill Europe
Parc Industriel Wavre Nord Avenue Vsale, 30 1300 Wavre Belgium Phone: 32.10.22.83.34 Fax: 32.10.22.83.38 Email: [email protected]

Tuthill Asia Pacific

19-21 Milton Park, 128 Canterbury Road Box 71, Kilsyth, Victoria 3137 Australia Phone: 61.3.9720.6533 Fax: 61.9.9720.6880 Email: [email protected]

Tuthill China Tuthill Latin America

1320 South Dixie Highway, Suite 761 Coral Gables, Florida 33146 USA Phone: 305-740-3381 Fax: 305-740-9328 Email: [email protected] Room 1507 Harbour Ring Plaza No. 18 Xizang Zhong Road Shanghai 200001 China Phone: 86.21.5385.3369 Fax: 86.21.5385.3365 Email: [email protected]

Tuthill Vacuum & Blower Systems (TVBS) is a pioneer in the development of vacuum pump technology. Introduced in 1926, the Kinney rotary piston vacuum principle still sets the industry standard for high performance, reliability, low maintenance and quiet operation in a mechanical vacuum pump design. These same performance features are demonstrated in all the TVBS vacuum pump product lines: liquid ring pumps, dry pumps, vane pumps and our main line of rotary piston pumps. In addition, all pump designs can be incorporated in complete TVBS-engineered vacuum systems. For information and specifications on other Kinney Vacuum Pumps and Systems, please contact us at 1-800-825-6937.

1148 R05/LP