CUTOUT Fuse Holders

(Standard)

CABLE SYSTEMS

COMPONENTS

OVERHEAD LINES

RAILWAY CATENARY SYSTEMS

www.pfisterer.co.za

[email protected]

Standard Type Cutout

Application
STANDARD Cutout Pages 3 - 9 The Primary purpose of any cutout is to provide protection for your system and the various apparatus on these lines, such as transformers and capacitor banks. PFISTERER cutouts provide reliable protection for low-level, intermediate and high-level faults. With the use of a portable Loadbreak tool, PFISTERER cutouts can function much like an overhead disconnect switch. Alternatively 200 amp Solid Links are available. Ratings & Specifications Standard PFISTERER cutouts have maximum design voltage ratings to simplify the choice of cutouts. There are no restrictions to grounded star, ungrounded star or delta systems having maximum operating voltages equal to, or less than the cutout maximum design rating. In each voltage class, these are continuous current ratings of 100A using fuse links and 200A using a solid disconnect link. See the charts for other specifications.

2
CABLE SYSTEMS
Revision 1 06.09.06

COMPONENTS

OVERHEAD LINES

RAILWAY CATENARY SYSTEMS

Standard Type Cutout

Quality Construction
Efficient Current Transfer The PFISTERER cutout has an all copper single piece current path with Silver-plated contacts. Terminals are tin-plated brass for use with copper or aluminium conductor. Loadbuster Hooks Galvanised steel hooks are standard on all PFISTERER cutouts, for use with a portable Loadbuster tool. The hooks are mounted under the top contact and serve as a guide for the fuse holder when closing at an off centre angle. Top Contact The top contact is designed such that it provides a smooth self aligning action during closing, The top contact is formed from highly conductive copper and is silver-plated, which provides a continuous current path from dome nut to PG clamp. The contact is designed to maintain firm and constant pressure with the fuse holder contact surface until fault interruption is accomplished. Backing the top contact is the Loadbreak bracket, which prevents over-racking. Used in conjunction with a load break tool of the correct rating, the cutout can be opened under load. Hinge The hinge on the cutouts employs a large pivot area for the fuse holders trunnion and is manufactured from brass for its strength and superior electrical properties. The hinge contacts are of a highly conductive copper alloy and silver-plated to ensure an efficient current transfer from the trunnion casting. Insulator (Silicone) All silicone bushings are manufactured from HTV silicone and have been tested in accordance to various international aging standards including; IEC 61109 Annex C, SCSPVAC17 KIPTS & ANSI C29-13-2000 Tracking & Erosion resistance. Leakage distances range from 380mm1130mm, with BIL ratings of 110kV-200kV. The advantages of HTV silicone are numerous, namely,

1.Silicones are the only housing materials that are able to transfer their intrinsic hydrophobic behavior to pollution layers. Therefore, leakage currents are suppressed and the risk of flashover is reduced. Moreover, composite insulators with silicone housings do not require cleaning. Some other polymers such as EPDM or some special Cycloaliphatics are also hydrophobic but not able to coat the pollution layers deposited on the housing surface. 2. High tensile strength to weight ratio. 3. Improved performance in highly polluted areas. 4. An unattractive target for vandals and very resistant to projectile damage. 5. Flexibility, providing better seismic capabilities and preventing cascade failure of post units. 6. High resistance to UV degradation. 7. High resistance to thermal extremes (-35oC to +50oC) Insulator (Porcelain) These insulators of sky-glazed grey porcelain, with leakage distances range from 230mm720mm, with BIL ratings of 110kV-170kV. Fuse Holder The solid cap on the single vent fuse holder is made of silver-plated brass, which provides efficient current transfer. An integral ring is provided in the top tube casting for opening and closing the fuse holder using conventional disconnect tools from the ground, from a bucket truck or from a cherry picker. The toggle type trunnion casting is of silver-plated brass for efficient current transfer to the lower hinge contacts. Cams on the trunnion ensure high-pressure current path to the lower contacts. The pivot bosses are cast full round for smooth rotational operation in the hinge but prevent the trunnion from disengaging when closing the fuse tube. The spring operated link ejector assists with clearing low-level fault currents. A groove in the centre of the link ejector guides the fuse tail directly from the fuse tube to the attachment nut. Radii on the link ejector minimise the bending stress on the fuse tail to prevent strands breaking.

CABLE SYSTEMS

COMPONENTS

OVERHEAD LINES

RAILWAY CATENARY SYSTEMS

Standard Type Cutout

Quality Construction cont..
The link ejector is pinned to the trunnion with a brass pin to provide resistance to corrosive elements and assure smooth pivotal action. An interlocking device between link ejector and bottom tube casting prevents excessive tension on the fuse link during closure, which could cause link breakage during closure. The link ejector employs an impact effect to ensure toggle action of the trunnion during low fault and overload interruptions. Dropout action is assured. The link ejector provides sufficient surface area to facilitate re-fusing by a linesman wearing gloves. Interchangeability PFISTERER Fuse carriers are interchangeable with all cutouts manufactured in accordance with the IEC 282 Specification. Fuse Tube The inside diameter of the 100A fuse tube increases the internal pressure, giving superior and reliable expulsion action. During frequently encountered intermediate fault ranges, this diameter also permits higher TRV, (Transient Recovery Voltage), values to be tolerated. The liner is constructed of an arc quenching material. The tube is manufactured from fibreglass, which permits a smaller bore and provides a higher burst strength. It is protected from the weather and environment by an ultra violet resistant coating. Brackets All mounting brackets are manufactured from steel to international standards and are hot dip galvanised in accordance with ISO 1461. Stainless steel options are available on request. Higher interrupt capacities By using a copper arc-shortening rod attached to the dome nut inside the top of the fuse tube, lowering the fuse link, higher interrupt ratings are obtainable. It is necessary to use fuse links with removable button heads when using an arc-shortening rod. Creepage PFISTERER cutouts are available for use under various pollution conditions. Units are available in 20mm/kV to 31mm/kV Creepage values. Extra Corrosion protection All PFISTERER cutouts are available with components made from stainless steel and plated copper alloy, to offer greater corrosion resistance for severely aggressive environments where corrosion can become a major factor. See ordering data page. Terminals Tin plated copper alloy parallel groove type terminals are standard on all PFISTERER cutouts. They can accommodate aluminium or copper conductor sizes ranging from 6-15mm. The parallel groove terminal is designed to accommodate two different size conductors, as is the case when arrestors are being used. Eyebolt and Lug mount options are also available.

Porcelain Cutouts
KV BIL 110 125 150 170 KV BIL 110 125 V 125 150 150 200 V 200 V 200 V A 348 370 370 383 A 362 432 376 376 376 518 828 642 B 164 200 200 240 B 158 188 200 200 200 178 274 217 C 247 393 393 333 C 253 236 295 295 295 309 315 351 D 502 643 643 771 D 509 493 642 642 642 659 758 791 E 28 4.2 4.2 1 E 13 38 3 3 -7 46 48 64 Creepage 230 380 660 720 Creepage 380 480 480 480 600 750 750 1130

Silicone Cutouts

V indicates that the unit is configured in a V profile utilising two bushings.

4
CABLE SYSTEMS | COMPONENTS | OVERHEAD LINES | RAILWAY CATENARY SYSTEMS

Standard Type Cutout

All PFISTERER Cutouts meet or exceed IEC / ANSI Specifications
Tin Plated Brass-Alloy terminals for use with copper or aluminium conductor Silver plated CopperAlloy current path

Secure alignment to prevent sideways movement of hooks and contact. Stainless steel back up spring for sustained contact pressure.

Stainless steel top hood, on all cutouts

Silicone Bushing

Galvanised steel hooks for Loadbuster tool. Hook bracket acts as over-racking stop.

Galvanised steel mounting pin Cast Brass-Alloy top tube casting and pull ring. High strength fibreglass fuse tube coated with Ultra-violet resistant paint.

Brass-Alloy current path

Hole in trunnion for hot stick

Silver-to-Silver contact with stainless steel back-up springs.

Cast Brass-Alloy bottom tube casting.

Brass-Alloy Hinge for corrosion resistance Stainless steel link ejector with toggle latch to limit tension on fuse link

CABLE SYSTEMS

COMPONENTS

OVERHEAD LINES

RAILWAY CATENARY SYSTEMS

Standard Type Cutout

Specifications and ordering information
Porcelain Cutouts
(110kV BIL)
Part # Insulator Type Fuse Holder No No Yes Yes Yes Yes Yes Yes Yes Yes Fuse Break No No No No No No Yes No No Yes Arc Shortening Rod No No No 4 No 4 No 4 No 4 Earth Stud Interrupt capacity (kA) 10/16* 10/16* 10 16 10 16 10 16 10 16 1 min Power frequency withstand (wet) (kV) Minimum Creepage Distance (mm) Arcing Distance (mm) Current Rating (Amps)

146 010-001 146 010-002 146 010-003 146 010-004 146 010-005 146 010-006 146 010-007 146 010-008 146 010-009 146 010-010

Porcelain

No Yes No No Yes Yes No No Yes Yes

45

230

190

100

(125kV BIL)
Part # Insulator Type Fuse Holder No No Yes Yes Yes Yes Yes Yes Yes Yes Fuse Break No No No No No No Yes No No Yes Arc Shortening Rod No No No 6 No 6 No 6 No 6 Earth Stud Interrupt capacity (kA) 8/12* 8/12* 8 12 8 12 8 12 8 12 1 min Power frequency withstand (wet) (kV)

* - Rating with 4 Arc Shortening Rod

Minimum Creepage Distance (mm)

Arcing Distance (mm)

Current Rating (Amps)

146 020-001 146 020-002 146 020-003 146 020-004 146 020-005 146 020-006 146 020-007 146 020-008 146 020-009 146 020-010

Porcelain

No Yes No No Yes Yes No No Yes Yes

50

398

230

100

(150kV BIL)
Part # Insulator Type Fuse Holder No No Yes Yes Yes Yes Yes Yes Yes Yes Fuse Break No No No No No No Yes No No Yes Arc Shortening Rod No No No 6 No 6 No 6 No 6 Earth Stud Interrupt capacity (kA) 8/12* 8/12* 8 12 8 12 8 12 8 12 1 min Power frequency withstand (wet) (kV)

* - Rating with 6 Arc Shortening Rod

Minimum Creepage Distance (mm) 545

Arcing Distance (mm)

Current Rating (Amps)

146 030-001 146 030-002 146 030-003 146 030-004 146 030-005 146 030-006 146 030-007 146 030-008 146 030-009 146 030-010

Porcelain

No Yes No No Yes Yes No No Yes Yes

50

230

100

(170kV BIL)
Part # Insulator Type Fuse Holder No No Yes Yes Yes Yes Fuse Break No No No No No Yes Arc Shortening Rod No No 6 6 6 6 Earth Stud Interrupt capacity (kA) 11.2* 11.2* 11.2* 11.2* 11.2* 11.2* 1 min Power frequency withstand (wet) (kV)

* - Rating with 4 Arc Shortening Rod

Minimum Creepage Distance (mm)

Arcing Distance (mm)

Current Rating (Amps)

146 040-001 146 040-002 146 040-003 146 040-004 146 040-005 146 040-006

Porcelain

No Yes No Yes No Yes

65

660

275

100

* - Rating with 6 Arc Shortening Rod

6
CABLE SYSTEMS | COMPONENTS | OVERHEAD LINES | RAILWAY CATENARY SYSTEMS

Standard Type Cutout

(170kV BIL)
Part # 146 050-001 146 050-002 146 050-003 146 050-004 146 050-005 146 050-006 Insulator Type Fuse Holder No No Yes Yes Yes Yes Fuse Break No No No No No Yes Arc Shortening Rod No No 8 8 8 8 Earth Stud No Yes No Yes No Yes Interrupt capacity (kA) 11.2* 11.2* 11.2* 11.2* 11.2* 11.2* 1 min Power frequency withstand (wet) (kV) Minimum Creepage Distance (mm) Arcing Distance (mm) Current Rating (Amps)

Porcelain

65

720

285

100

Silicone Cutouts
(110kV BIL)
Part # Insulator Type Fuse Holder No No Yes Yes Yes Yes Yes Yes Yes Yes Fuse Break No No No No No No Yes No No Yes Arc Shortening Rod No No No 4 No 4 No 4 No 4 Earth Stud Interrupt capacity (kA) 10/16* 10/16* 10 16 10 16 10 16 10 16 1 min Power frequency withstand (wet) (kV)

* - Rating with 8 Arc Shortening Rod

Minimum Creepage Distance (mm)

Arcing Distance (mm)

Current Rating (Amps)

146 060-001 146 060-002 146 060-003 146 060-004 146 060-005 146 060-006 146 060-007 146 060-008 146 060-009 146 060-010

Silicone

No Yes No No Yes Yes No No Yes Yes

45

380

140

100

(110kV BIL)
Part # Insulator Type Fuse Holder No No Yes Yes Yes Yes Yes Yes Yes Yes Fuse Break No No No No No No Yes No No Yes Arc Shortening Rod No No No 4 No 4 No 4 No 4 Earth Stud Interrupt capacity (kA) 10/16* 10/16* 10 16 10 16 10 16 10 16 1 min Power frequency withstand (wet) (kV)

* - Rating with 4 Arc Shortening Rod

Minimum Creepage Distance (mm)

Arcing Distance (mm)

Current Rating (Amps)

146 070-001 146 070-002 146 070-003 146 070-004 146 070-005 146 070-006 146 070-007 146 070-008 146 070-009 146 070-010

Silicone

No Yes No No Yes Yes No No Yes Yes

45

480

205

100

(125kV BIL)
Part # Insulator Type Fuse Holder No No Yes Yes Yes Yes Yes Yes Yes Yes Fuse Break No No No No No No Yes No No Yes Arc Shortening Rod No No No 6 No 6 No 6 No 6 Earth Stud Interrupt capacity (kA) 8/12* 8/12* 8 12 8 12 8 12 8 12 1 min Power frequency withstand (wet) (kV)

* - Rating with 4 Arc Shortening Rod

Minimum Creepage Distance (mm)

Arcing Distance (mm)

Current Rating (Amps)

146 080-001 146 080-002 146 080-003 146 080-004 146 080-005 146 080-006 146 080-007 146 080-008 146 080-009 146 080-010

Silicone

No Yes No No Yes Yes No No Yes Yes

60

480

177

100

* - Rating with 6Arc Shortening Rod

CABLE SYSTEMS

COMPONENTS

OVERHEAD LINES

RAILWAY CATENARY SYSTEMS

Standard Type Cutout

(150kV BIL)
Part # 146 090-001 146 090-002 146 090-003 146 090-004 146 090-005 146 090-006 146 090-007 146 090-008 146 090-009 146 090-010 Insulator Type Fuse Holder No No Yes Yes Yes Yes Yes Yes Yes Yes Fuse Break No No No No No No Yes No No Yes Arc Shortening Rod No No No 6 No 6 No 6 No 6 Earth Stud No Yes No No Yes Yes No No Yes Yes Interrupt capacity (kA) 8/12* 8/12* 8 12 8 12 8 12 8 12 1 min Power frequency withstand (wet) (kV) Minimum Creepage Distance (mm) Arcing Distance (mm) Current Rating (Amps)

Silicone

60

480

205

100

(150kV BIL)
Part # Insulator Type Fuse Holder No No Yes Yes Yes Yes Yes Yes Yes Yes Fuse Break No No No No No No Yes No No Yes Arc Shortening Rod No No No 6 No 6 No 6 No 6 Earth Stud Interrupt capacity (kA) 8/12* 8/12* 8 12 8 12 8 12 8 12 1 min Power frequency withstand (wet) (kV)

* - Rating with 6 Arc Shortening Rod

Minimum Creepage Distance (mm) 600

Arcing Distance (mm)

Current Rating (Amps)

146 100-001 146 100-002 146 100-003 146 100-004 146 100-005 146 100-006 146 100-007 146 100-008 146 100-009 146 100-010

Silicone

No Yes No No Yes Yes No No Yes Yes

62

210

100

(200kV BIL)
Part # Insulator Type Fuse Holder No No Yes Yes Yes Yes Yes Yes Yes Yes Fuse Break No No No No No No Yes No No Yes Arc Shortening Rod No No No 6 No 6 No 6 No 6 Earth Stud Interrupt capacity (kA) 8/12* 8/12* 8 12 8 12 8 12 8 12 1 min Power frequency withstand (wet) (kV)

* - Rating with 6 Arc Shortening Rod

Minimum Creepage Distance (mm)

Arcing Distance (mm)

Current Rating (Amps)

146 110-001 146 110-002 146 110-003 146 110-004 146 110-005 146 110-006 146 110-007 146 110-008 146 110-009 146 110-010

Silicone

No Yes No No Yes Yes No No Yes Yes

60

750

288

100

(200kV BIL)
Part # Insulator Type Fuse Holder No No Yes Yes Yes Yes Fuse Break No No No No No Yes Arc Shortening Rod No No 8 8 8 8 Earth Stud Interrupt capacity (kA) 11.2* 11.2* 11.2* 11.2* 11.2* 11.2* 1 min Power frequency withstand (wet) (kV)

* - Rating with 8 Arc Shortening Rod

Minimum Creepage Distance (mm)

Arcing Distance (mm)

Current Rating (Amps)

146 120-001 146 120-002 146 120-003 146 120-004 146 120-005 146 120-006

Silicone

No Yes No Yes No Yes

60

750

288

100

* - Rating with 8 Arc Shortening Rod

8
CABLE SYSTEMS | COMPONENTS | OVERHEAD LINES | RAILWAY CATENARY SYSTEMS

Standard Type Cutout

(200kV BIL)
Part # 146 130-001 146 130-002 146 130-003 146 130-004 146 130-005 146 130-006 Insulator Type Fuse Holder No No Yes Yes Yes Yes Fuse Break No No No No No Yes Arc Shortening Rod No No 8 8 8 8 Earth Stud No Yes No Yes No Yes Interrupt capacity (kA) 11.2* 11.2* 11.2* 11.2* 11.2* 11.2* 1 min Power frequency withstand (wet) (kV) Minimum Creepage Distance (mm) Arcing Distance (mm) Current Rating (Amps)

Silicone

81

1130

345

100

* - Rating with 8 Arc Shortening Rod

CABLE SYSTEMS

COMPONENTS

OVERHEAD LINES

RAILWAY CATENARY SYSTEMS