Engineering GTX

GTX LTR / Privacy Plus
900 MHz
Mobile Radio Service Manual
6880906Z19-O
Product Software License Agreement

THIS LICENSE AGREEMENT BETWEEN YOU, THE USER, AND MOTOROLA, APPLIES TO THE SOFTWARE EMBEDDED IN OR DELIVERED WITH THE ACCOMPANYING MOTOROLA PRODUCT (SOFTWARE), AND IS APPLICABLE UNLESS A SIGNED LICENSE AGREEMENT COVERING ITS SUBJECT MATTER HAS BEEN EXECUTED BETWEEN YOU AND MOTOROLA. BY USING THE PRODUCT, YOU ACKNOWLEDGE THAT THIS AGREEMENT HAS BEEN READ AND UNDERSTOOD AND THAT YOU AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. IF YOU DO NOT AGREE, YOU ARE NOT LICENSED TO USE THE PRODUCT, AND IF YOU ARE THE PURCHASER OF THE PRODUCT, YOU SHOULD IMMEDIATELY RETURN THE PRODUCT IN ITS ENTIRETY TO ITS PLACE OF PURCHASE FOR A REFUND. Motorola grants to You a non-exclusive license to use the SOFTWARE in the manner described in the documentation associated with the product. Motorola retains ownership of the SOFTWARE including all patent, copyrights, and other intellectual property rights. You may transfer this license to use the SOFTWARE as long as the transferee agrees to be bound by the terms of this Agreement. You agree not to reverse engineer or create derivative works of the SOFTWARE; not to transmit the SOFTWARE electronically; not to modify, congure, or use the SOFTWARE in any manner not authorized by MOTOROLA; and, except as an integral part of the product, not to rent, lease, or convey the SOFTWARE. MOTOROLA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF THIS SOFTWARE. With respect to the U.S. Government, if acquired under FAR policy (52.227-19), the SOFTWARE is provided with Restricted Rights, and if acquired under DFARS policy (227.7202), then the SOFTWARE is provided only with the commercial rights of this Agreement. This license is effective until terminated. It will terminate immediately and automatically if You fail to comply with any term of this Agreement. You agree that this is the complete and exclusive statement of the agreement between You and Motorola and that any modication of these terms shall be made only by mutual agreement and evidenced by written amendment signed by both parties. This Agreement shall be governed and interpreted by the laws of the State of Illinois, United States of America.
Computer Software Copyrights

This manual may not be reproduced, in whole or in part, in any form whatsoever, without the express written permission of Motorola, Inc. The Motorola products described in this manual contain one or more computer programs. These computer programs are protected by copyright law and international treaties. Unauthorized reproduction or distribution of these programs, or any part thereof, may result in severe civil and criminal penalties, and will be prosecuted to the maximum extent possible under the law. U.S. and international patents pending.
, MOTOROLA, and PRIVACY PLUS are registered trademarks of Motorola, Inc. GTX is a trademark of Motorola, Inc. LTR is a registered trademark of E.F. Johnson Company. TORX is a registered trademark of Camcar/Textron. 2000 by Motorola, Inc. All Rights Reserved.
This product is covered by one or more issued U.S. Patents. Other Patent applications pending.
Table of Contents
Foreword
Scope of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi How to Use This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Service Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Ordering Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Model Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Maintenance Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .x Radio Model Numbering System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xii
Section 1
Introduction
Notational Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Scope of this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Air Bag Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Vehicles Equipped with Air Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 LP Gas Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Section 2
Basic Maintenance
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Plastic Surfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Circuit Boards and Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Safe Handling of CMOS Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Repair Procedures and Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Parts Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Rigid Circuit Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Chip Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Chip Component Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Chip Component Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Over-Molded Pad-Array Carrier (OMPAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 OMPAC Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 OMPAC Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Shield Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Shield Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Replacement of Transistor Q6505 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
September, 2000
6880906Z19-O
Table of Contents
GTX LTR / Privacy Plus 900 MHz Mobile Radio Service Manual
Removing Faulty Transistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Preparing Main Board for New Transistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Positioning New Transistor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Soldering Transistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Installing Flange Capacitors C6567 and C6568. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Reassembly of Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Section 3
Test Equipment, Service Aids, and Tools

Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Field Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Service Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Section 4
Test Mode, Error Codes and Performance Tests

Front Panel Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Test Mode/Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Test Mode/Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Test Mode/Tx Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Fail Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Exiting Test Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Section 5
Disassembly & Reassembly For 12 W Models

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Disassemble the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Remove the Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Remove the Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Remove the Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Disassemble the Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Assemble the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Assemble the Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Replace the Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Replace the Top Cover and Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Section 6
Disassembly & Reassembly For 30 W Models

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Disassemble the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Remove the Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Remove the Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Remove the Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Disassemble the Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Assemble the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Assemble the Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Replace the Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Replace the Top Cover and Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
ii
6880906Z19-O
September, 2000
Table of Contents
Section 7
Radio Tuning Procedure

Radio Tuning Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Service Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Tuning Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Starting the Tuning Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Alignment Default Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Tx Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Reference Oscillator Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Transmitter Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Transmit Current Limit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Transmit Deviation Balance (Compensation) & Deviation Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Transmit Deviation Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Ending the Tuning Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4
Section 8
Theory of Operation
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Receiver Detailed Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Transmitter Detailed Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 12 Watt PA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 30 Watt PA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 Power Control Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Power Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Current Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Thermal Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Synthesizer Detailed Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Controller Detailed Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 Voltage Regulators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 Electronic On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 Mechanical On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Microprocessor Clock Synthesizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Serial Peripheral Interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 SBEP Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Microprocessor (Open Controller) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 One-Time Programmable (Flash) Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8 Electrically Erasable Programmable Memory (EEPROM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8 Static Random Access Memory (SRAM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Controller Audio & Signaling Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Audio Signalling Filter IC (ASFIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Audio Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9 Transmit Audio Circuits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Mic Input Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Flat Tx Audio Input Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 PTT Sensing and TX Audio Processing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Transmit Signalling Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Sub-audible Data (PL/DPL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11 High Speed Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11 Dual Tone Multiple Frequency (DTMF) Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11 Receive Audio Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12
September, 2000 6880906Z19-O
iii
Table of Contents
Audio Processing and Digital Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13 Audio Amplication Speaker (+) Speaker (-). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13 Handset Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13 External Rx Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14 Receive Signalling Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14 Sub-audible Data (PL/DPL) and High Speed Data Decoder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14 Alert Tone Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15 Hear Clear IC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15 Transmit Path for Radios with Hear Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15 Receive Path for Radios with Hear Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15 Hear Clear Routing of Data/Signalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16 Accessory Connector Congurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16 Remote Desk Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16 Public Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17 External Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17 RSSI Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17
Section 9
Troubleshooting
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Troubleshooting Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Troubleshooting Flow Chart for Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Troubleshooting Flow Chart for Synthesizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4 Troubleshooting Flow Chart for 12 W Power Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 Troubleshooting Flow Chart for 30 W Power Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7 Troubleshooting Flow Chart for Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8 Troubleshooting Flow Chart for Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Schematic Diagrams, Circuit Board Details, and Parts Lists

Schematic Diagram for HLF9003A, HLF9004A, HLF9009A & HLF9010A Main Boards, Radio Block Diagram Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Schematic Diagram for HLF9003A, HLF9004A, HLF9009A & HLF9010A Main Boards, Receiver Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Schematic Diagram for HLF9003A, HLF9004A, HLF9009A & HLF9010A Main Boards, Synthesizer Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Schematic Diagram for HLF9003A & HLF9004A Main Boards, Power Amplifier Section . . . . . . . . . . . . . . . . . .4 Schematic Diagram for HLF9003A & HLF9004A Main Boards, Power Control Section . . . . . . . . . . . . . . . . . . . .5 Schematic Diagram for HLF9009A & HLF9010A Main Boards, Power Amplifier Section . . . . . . . . . . . . . . . . . .6 Schematic Diagram for HLF9009A & HLF9010A Main Boards, Power Control Section . . . . . . . . . . . . . . . . . . . .7 Schematic Diagram for HLF9003A, HLF9004A, HLF9009A & HLF9010A Main Boards, Controller Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Schematic Diagram for HLF9003A, HLF9004A, HLF9009A & HLF9010A Main Boards, Audio & Digital Controller Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Schematic Diagram for HLF9003, HLF9004A, HLF9009A & HLF9010A Main Board, Audio PA & I/O Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Schematic Diagram for HLF9003A, HLF9004A, HLF9009A & HLF9010A Main Boards, Supply Voltage Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Schematic Diagram for HLF9003, HLF9004A, HLF9009A & HLF9010A Main Board, Hear Clear Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Circuit Board Details for HLF9003A & HLF9004A Main Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Parts List for HLF9003A & HLF9004A Main Boards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Circuit Board Details for HLF9009A & HLF9010A Main Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Parts List for HLF9009A & HLF9010A Main Boards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
iv
6880906Z19-O
September, 2000
Table of Contents
Schematic Diagram for FLN8744A Control Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Circuit Board Details & Parts List for FLN8744A Control Head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 GTX Exploded View & Mechanical Parts List, 30 W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 GTX Exploded View & Mechanical Parts List, 12 W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
September, 2000
6880906Z19-O
Foreword Scope of Manual
GTX LTR / Privacy Plus 900 MHz Mobile Service Manual
Scope of Manual
This manual is intended for use by experienced technicians familiar with similar types of equipment. It contains all service information required for the equipment described and is current as of the printing date. Changes which occur after the printing date are incorporated by service manual revisions. These revisions are added to the manuals as the engineering changes are incorporated into the equipment.
order the number of the chassis or kit which contains the part, and a detailed description of the desired component. If a Motorola part number is identified on a parts list, you should be able to order the part through Motorola Parts. If only a generic part is listed, the part is not normally available through Motorola. If no parts list is shown, generally, no user serviceable parts are available for the kit. Radius 30-Day Warranty Technical Support Radius Product Services 8000 W. Sunrise Blvd. Plantation, FL 33322 Motorola Radio Support Center Attention: Warranty Return 3761 South Central Avenue Rockford, IL 61102 USA 1-800-227-6772 (U.S. & Canada) Radius Major Component Repair Motorola Radio Support Center 3760 South Central Avenue Rockford, IL 61102 USA Motorola Parts Worldwide System and Aftermarket Products Division Attention: Order Processing 1313 E. Algonquin Road Schaumburg, IL 60196 Worldwide System and Aftermarket Products Division Attention: International Order Processing 1313 E. Algonquin Road Schaumburg, IL 60196 Customer Service 1-800-422-4210 1-847-538-8198 (FAX) Parts Identication 1-847-538-0021 1-847-538-8194 (FAX)
How to Use This Manual

This manual contains introductory material such as model charts, accessories, and specications, as well as four sections that deal with specific service aspects of the GTX Mobile Radio. Refer to the Table of Contents for a general overview of the manual, or to the Overview paragraph in each section for a specic overview of the information in that section.
Technical Support
To obtain technical support, you may call Motorolas Radius Product Services. When you call, we ask that you have ready the model and serial numbers of the respective radio or its parts.
Service Policy
If malfunctions occur within 30 days that cannot be resolved over the phone with Product Services, a defective major component should be returned. You must obtain authorization from Radius Product Services before returning the component.
Ordering Replacement Parts

You can order additional components and some piece parts directly through your Radius price pages. When ordering replacement parts, include the complete identication number for all chassis, kits, and components. If you do not know a part number, include with your
vi
6880906Z19-O
September, 2000
Foreword Model Chart
Model Chart
GTX Privacy Plus, 900 MHz, 12.5 kHz, 12 W
GTX LTR, 900 MHz, 12.5 kHz, 12 W
Main Board, Privacy Plus, 12.5 kHz, 12 W HLF9009_ X X
Description
M11WGD4CU1_N
M11WGD4CB1_N
Model
HLF90010_ X X
Item
HLN9634_
Item
X X X X X X X X X X X X X X X X X X HUF3029_ HUF3031_ HUF3030_ HUF3032_ HCN3018_ HMN3413_ GLN7317_ GKN6270_ 6880907Z66 6880907Z20 6880907Z19
Description
Radio, Privacy Plus, 12.5 kHz, 12 W Radio, LTR, 12.5 kHz, 12 W Unied Chassis, Privacy Plus, 12.5 kHz, 12 W Unied Chassis, LTR, 12.5 kHz, 12 W Control Head Compact Microphone Trunnion Power Cable Installation Manual GTX LTR Users Guide (English/French) GTX Privacy Plus Users Guide (English/French)
FLN8744_ X
Control Head Board
Hardware Kit
Freq..
GTX LTR / Privacy Plus Mobile Radio 900 MHz 12 Watts RF Power
Main Board, LTR, 12.5 kHz, 12 W
Description
September, 2000
6880906Z19-O
vii
Foreword Model Chart
GTX Privacy Plus, 900 MHz, 12.5 kHz, 30 W
GTX LTR, 900 MHz, 12.5 kHz, 30 W
Main Board, Privacy Plus, 12.5 kHz, 30 W HLF9003_ X X
Description
M11WRD4CU1_N
M11WRD4CB1_N
Model
Item
HLN9634_
HLF9004_ X X
Item
X X X X X X X X X HUF3007_ X HUF3011_ HUF3009_ X HUF3013_ X FCN3018 X HMN3413_ X HLN9640_ X HKN4191_ X 6880907Z66 X 6880907Z20 X 6880907Z19
Description
Radio, Privacy Plus, 12.5 kHz, 30 W Radio, LTR, 12.5 kHz, 30 W Unied Chassis, Privacy Plus, 12.5 kHz, 30 W Unied Chassis, LTR, 12.5 kHz, 30 W Control Head Compact Microphone Trunnion Power Cable Installation Manual GTX LTR Users Guide (English/French) GTX Privacy Plus Users Guide (English/French)
viii
6880906Z19-O
September, 2000
FLN8744_ X
Control Head Board
Hardware Kit
Freq.
GTX LTR / Privacy Plus Mobile Radio 900 MHz 30 Watts RF Power
Main Board, LTR, 12.5 kHz, 30 W
Description
Foreword Accessories
Accessories
Audio HMN3413 HMN1035_R HMN3013 AAREX4617 HLN9073 Speaker FSN5510 Installation HLN9640 GLN7317 Cables HKN4191 GKN7270 GKN6271 GKN6272 Antennas RRA4935 Control Station RLN4834 HLN3067 GLN7318 HPN4001 HPN4002 HKN9088 HMN3000 Manuals/Kits 6880907Z20 6880907Z19 6880907Z66 RVN4150
September, 2000
Compact Microphone Heavy Duty Palm Microphone DTMF Non-Backlit Microphone with Hang-Up Clip Handset with Hang-up Clip Hang-up Clip
7.5 W External Speaker
Trunnion Kit; 30 W Trunnion Kit; 12 W
Power Cable; 30 W Power Cable; 12 W Ignition Sense Cable External Alarm Relay and Cable
900 MHz, 3 dB Gain w/14 ft. Cable
Control Station Package; 30 W Control Station Package; 12 W Base Station Tray Power Supply and Cable (greater than 25 W) Power Supply and Cable (less than or equal to 25 W) Mobile Mini-U Antenna Adapter Desk Micophone
GTX LTR Users Guide (English/French) GTX Privacy Plus Users Guide (English/French) Installation Manual GTX Radio Service Software Kit
6880906Z19-O
ix
Foreword Maintenance Specifications
Maintenance Specications
GENERAL
Frequency: Model Number: RF Output: RF Output (Talkaround): FCC Description: Dimensions (H x W x L): Weight: 900 MHz M11WRD4CB1_N, M11WRD4CU1_N M11WGD4CB1_N, M11WGD4CU1_N 30 W 12 W 20 W 10 W ABZ99FT3004 AZ492FT5782 1.73 x 6.61 x 8.62 1.73 x 6.61 x 6.67 (44mm x 168mm x 219mm) (44mm x 168mm x 169mm) 4.30 lb 2.67 lb (1.95 kg) (1.21 kg) 896 941 MHz 896 902 MHz 935 941 MHz 935 941 MHz 12.5 kHz 10 Trunked Modes / 10 Conventional Channels 8 Trunked Talkgroups 1.5 ppm 13.6 V dc 13.8 V dc -30 to +60C -40 to +85C 6.0A (12 W)
Frequency Range *: Transmit Talkaround Receive Channel Spacing: Channel Capacity: Group Capacity: Frequency Stability: Input Voltage: Temperature Range: Operating Storage Tx Current: 12.0A (30 W) * 821 - 825 MHz & 866 - 870 MHz is available outside of the U.S.
TRANSMITTER
Power Output: Channel Spacing: Maximum Frequency Separation: Modulation Limiting: FM Hum & Noise: Conducted / Radiated Emission: Audio Response (300-3000 Hz): Audio Distortion: 30 W (896 902 MHz) 20 W (935 941 MHz) 12.5 kHz 6 MHz 2.5 kHz -35 dB -13 dBm +1 to -3 dB Less than 5% 12 W (896 902 MHz) 10 W (835 941 MHz)
RECEIVER
Channel Spacing: Sensitivity (12dB SINAD): Intermodulation: Adjacent Channel Selectivity: Spurious Rejection: Audio Output Power: Audio Distortion @ Rated Audio: Current Drain: OFF Standby Rated Conducted Spurious Emission: 12.5 kHz 0.35 V -65 dB -65 dB -65 dB 4W (internal speaker) 7.5W (external speaker) 5% 30 mA 450 mA 1.5A (4W internal speaker) 1.7A (7.5W external speaker) Per FCC part 90
6880906Z19-O September, 2000
Foreword Maintenance Specifications
MIL STANDARDS- THE GTX MOBILE RADIO IS DESIGNED TO MEET OR EXCEED MOST REQUIREMENTS FOR MIL STD 810 C, D, AND E
810C Applicable MIL-STD: Low Pressure High Temperature Low Temperature Temperature Shock Rain Humidity Salt Fog Dust Vibration Shock Crash Safety Shock Packaged Vibration Methods 500.1 501.1 502.1 503.1 506.1 507.1 509.1 510.1 514.2 516.2 Procedures 1 1,2 1 1 2 2 1 1 8,10 1,3,5 Methods 500.2 501.2 502.2 503.2 506.2 507.2 509.2 510.2 514.3 516.3 810D Procedures 1 1,2 1,2 1 2 2 1 1 1 1,5 Methods 500.3 501.3 502.3 503.3 506.3 507.3 509.3 510.3 514.4 516.4 516.4 514.4 810E Procedures 1 1,2 1,2 1 2 2 1 1 1 1,5 5
All specications subject to change without notice.
September, 2000
6880906Z19-O
xi
Foreword Radio Model Numbering System
Radio Model Numbering System

The model number, serial number, and Motorola FCC designation number are all on a label attached to the back of your radio. All GTX LTR and Privacy Plus radio models are synthesized, 8 trunked mode, 10-conventional channel units that come standard with Tone Private-Line (TPL)/Digital Private-Line (DPL) coded squelch or carrier squelch, which may be enabled/disabled on a per channel basis. Programming changes can be made by your local dealer.
GTX Privacy Plus

Model Number: Position:
Position 1 - Type of Unit M = Mobile Position 2 & 3 - Model Series Position 4 - Frequency Band 896-941 MHz Position 5 - Power Level 30 W Position 6 - Physical Package Standard Control with Display Position 7 - Channel Spacing 12.5 kHz
M 1
1 2
1 3
W 4
R 5
D 6
4 7
C 8
B 9
1 10
A 11
N 12
Position 12 Unique Model Variations Standard Package Position 11- Version
Version Letter (Alpha) - Major Change Position 10 - Feature Level Basic Position 9 - Primary System Type Privacy Plus Position 8 - Primary Operation Trunked Twin Type
GTX LTR
Position 1 - Type of Unit M = Mobile Position 2 & 3 - Model Series Position 4 - Frequency Band 896-941 MHz Position 5 - Power Level 30 W Position 6 - Physical Package Standard Control with Display Position 7 - Channel Spacing 12.5 kHz Position 8 - Primary Operation Trunked Twin Type
M 1
1 2
1 3
W 4
R 5
D 6
4 7
C 8
U 9
1 10
A 11
N 12
Version Letter (Alpha) - Major Change Position 10 - Feature Level Basic Position 9 - LTR
xii
6880906Z19-O
September, 2000
GTX Privacy Plus

Position 1 - Type of Unit M = Mobile Position 2 & 3 - Model Series Position 4 - Frequency Band 896-941 MHz Position 5 - Power Level 12 W Position 6 - Physical Package Standard Control with Display Position 7 - Channel Spacing 12.5 kHz
M 1
1 2
1 3
W 4
G 5
D 6
4 7
C 8
B 9
1 10
A 11
N 12
Version Letter (Alpha) - Major Change Position 10 - Feature Level Basic Position 9 - Primary System Type Privacy Plus Position 8 - Primary Operation Trunked Twin Type
GTX LTR
Position 1 - Type of Unit M = Mobile Position 2 & 3 - Model Series Position 4 - Frequency Band 896-941 MHz Position 5 - Power Level 12 W Position 6 - Physical Package Standard Control with Display Position 7 - Channel Spacing 12.5 kHz Position 8 - Primary Operation Trunked Twin Type
M 1
1 2
1 3
W 4
G 5
D 6
4 7
C 8
U 9
1 10
A 11
N 12
Version Letter (Alpha) - Major Change Position 10 - Feature Level Basic Position 9 - LTR
September, 2000
6880906Z19-O
xiii
xiv
6880906Z19-O
September, 2000
Section 1 Introduction
Notational Conventions
Throughout the text in this publication, you will notice the use of warnings, cautions, and notes. These notations are used to emphasize that safety hazards exist, and care must be taken and observed.
Safety information
Every radio, when transmitting, radiates energy into the atmosphere which may, under certain conditions, causes the generation of a spark. All users of vehicles tted with radios should be aware of the following warnings:
Warning
WARNING Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
WARNING Do not operate the radio near ammable liquids or in the vicinity of explosive devices. During normal use, the radio will subject you to radio energy substantially below the level where any kind of harm is reported. To ensure personal safety, please observe the following simple rules: WARNING
Caution
CAUTION Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. CAUTION may also be used to alert against unsafe practices and property-damage-only accident hazards.
Note
NOTE An operational procedure, practice, or condition, etc., which it is essential to emphasize.
Do not transmit when the antenna is very close to, or touching, exposed parts of the body, especially the face and eyes. Do not hold the transmit (PTT) key in when not desiring to transmit. Check the laws and regulations on the use of two-way mobile radios in the areas where you drive. Always obey them. Also, when using your radio while driving, please: give full attention to driving, use hands-free operation, if available, and pull off the road and park before making or answering a call if driving conditions so require.
Scope of this Manual

This manual includes model/kit information, specifications, disassembly/reassembly procedures, maintenance, alignment, troubleshooting, and all theory, schematic diagrams, printed circuit board details and parts lists for all parts in the equipment described. CAUTION This manual is intended for use by experienced technicians who are familiar with similar types of equipment.
September, 2000
6880906Z19-O
1-1
Introduction Air Bag Warning
GTX LTR/Privacy Plus 900 MHz Mobile Service Manual
Air Bag Warning

Vehicles Equipped with Air Bags
WARNING An air bag inflates with great force. Do not place objects, including communication equipment, in the area over the air bag or in the air bag deployment area. If the communication equipment is improperly installed and the air bag inates, this could cause serious injury. Installation of vehicle equipment should be performed by a professional installer/technician qualified in the requirements for such installations. An air bags size, shape and deployment area can vary by vehicle make, model and front compartment conguration (e.g., bench seat vs. bucket seats). Contact the vehicle manufacturers corporate headquarters, if necessary, for specific air bag information for the vehicle make, model and front compartment configuration
involved in your communication equipment installation.
LP Gas Warning
WARNING It is mandatory that radios installed in vehicles fueled by liquefied petroleum gas conform to the National Fire Protection Association standard NFPA 58, which applies to vehicles with a liquid propane (LP) gas container in the trunk or other sealed off space within the interior of the vehicle. The NFPA 58 requires the following: Any space containing radio equipment shall be isolated by a seal from the space in which the LP gas container and its ttings are located. Removable (outside) lling connections shall be used. The container space shall be vented to the outside.
1-2
6880906Z19-O
September, 2000
Section 2 Basic Maintenance
Introduction
This section of the manual describes preventive maintenance, safe handling of CMOS devices, and repair procedures and techniques. Each of these topics provides information vital to the successful operation and maintenance of your radio.
lint-free cloth or tissue should be used to remove the solution and dry the radio. Make sure that no water remains entrapped near the connectors, cracks, or crevices.
Circuit Boards and Components

Isopropyl alcohol may be applied with a stiff, nonmetallic, short-bristled brush to dislodge embedded or caked material located in hard-to-reach areas. The brush stroke should direct the dislodged material out and away from the inside of the radio. CAUTION Alcohol is a high-wetting liquid and can carry contamination into unwanted places if an excessive quantity is used. Make sure that controls or tunable components are not soaked with the liquid. Do not use high-pressure air to hasten the drying process. This could cause the liquid to puddle and collect in unwanted places. Upon completion of the cleaning process, use a soft, absorbent, lint-free cloth to dry the area. Do not brush or apply any isopropyl alcohol to the frame, front cover, or back cover. NOTE Always use a fresh supply of isopropyl alcohol and a clean container to prevent contamination by dissolved material from previous usage.
Preventive Maintenance
The radios do not require a scheduled preventive maintenance program; however, periodic visual inspection and cleaning is recommended.
Inspection
Check that the external surfaces of the radios are clean, and that all external controls and switches are functional. A detailed inspection of the interior electronic circuitry is not needed or desired.
Cleaning
CAUTION The effects of certain chemical and their vapors can have harmful results on certain plastics. Aerosol sprays, tuner cleaners, and other chemicals should be avoided. The following procedures describe the recommended cleaning agents and the methods to be used when cleaning the external and internal surfaces of the radio. External surfaces include the front cover, housing and assembly. These surfaces should be cleaned whenever a visual inspection reveals the presence of smudges, grease, and/or grime. Internal surfaces should be cleaned only when the radio is disassembled for servicing or repair. The only recommended agent for cleaning the external radio surfaces is a 0.5%solution of mild dishwashing detergent in water. the only factory recommended liquid for cleaning the printed circuits boards and their components is isopropyl alcohol (70% by volume).
Safe Handling of CMOS Devices

Complementary metal-oxide semiconductor (CMOS) devices are used in this family of radios. While the attributes of CMOS are many, their characteristics make them susceptible to damage by electrostatic or high voltage charges. Damage can be latent, resulting in failures occurring weeks or months later. Therefore, special precautions must be taken to prevent device damage during disassembly, troubleshooting, and repair. Handling precautions are mandatory for CMOS circuits and are especially important in low humidity conditions. CAUTION Do not attempt to disassemble the radio without observing the following handling precautions.
Plastic Surfaces
The detergent solution should be applied sparingly with a stiff non-metallic, short-bristled brush to work all loose dirt away from the radio. A soft, absorbent,
September, 2000
6880906Z19-O
2-1
Basic Maintenance Repair Procedures and Techniques
Precautions
1. 2. Eliminate static generators (plastics, stryofoam, etc. in the work area. Remove nylon or double-knit polyester jackets, roll up long sleeves, and remove or tie back loose hanging neckties. Store and transport all static-sensitive devices in ESD-protective containers. If at all possible, handle CMOS devices by the package and not by the leads. Prior to touching the unit, touch an electrical ground to remove any static charge that you may have accumulated. The package and substrate may be electrically common. If so, the reaction of a discharge to the case would cause the same dame as touching the leads. Disconnect all power from the unit before ESD-sensitive components are removed or inserted unless otherwise noted. Use a static safeguarded workstation, which can be accomplished through the use of an anti-static kit (Motorola part number 0180386A82). This kit includes a writ strap, two ground cords, a static-control table mat and a static-control oor mat. For additional information, refer to Service and Repair Note SRN F1052, Static Control Equipment for Servicing ESD Sensitive Products, available form Motorola Literature Distribution 2290 Hammond Drive Schaumburg, IL 60173 (847) 576-2826. When these items are not readily available, observing the following techniques will minimize chance of damage. If a static-sensitive device is to be temporarily set down, use a conductive surface for placement of the device. Make skin contact with a conductive work surface first and maintain this contact when the device is set down or picked up. 7. Always wear a conductive strip when servicing this equipment. the Motorola part number for a replacement wrist strap that connects to the table mat is 42-80385A59. When straightening CMOS pins, provide ground straps for apparatus used. When soldering, use a grounded soldering iron.
Repair Procedures and Techniques

The radio support center is at the following addresses: Motorola Radio Support Center 3651 South Central Avenue Rockford, Ill, 61102 Telephone: (800) 227-6772 (815) 847-1400 Refer to the Disassembly and Reassembly section of the manual for pertinent information prior to replacing and substituting parts.
3. 4.
Parts Replacement
Special care should be taken to be as certain as possible that a suspected component is actually the one at fault. This special care will eliminate unnecessary unsoldering and removal of parts, which could damage or weaken other components or the printed circuit board itself. When damaged parts are replaced, identical parts should be used. If the identical replacement component is not locally available, check the parts list for the proper Motorola part number and order the component from the nearest Motorola Communications Parts ofce.
5.
6.
Rigid Circuit Boards

This family of radios uses bonded, multi-layer, printed circuit boards. Since the inner layers are not accessible, some special considerations are required when soldering and unsoldering components. The printed-through holes may interconnect multiple layers of the printed circuit. CAUTION Therefore, care should be exercised to avoid pulling the plated circuit out of the hole. When soldering near the 16 or 18-pin connector, use care to avoid accidentally getting solder in the connector. CAUTION Be careful not to form solder bridges between the connector pins. Closely examine your work for shorts due to solder bridges.
Chip Components
Use either the RLN4062 Hot-Air Repair Station or the Motorola 0180381B45 Repair Station for chip component replacement. When using the 0180381B45 Repair Station, select the TJ-65 mini-thermojet hand piece. On either unit, adjust the temperature control to 700 F
8. 9.
2-2
6880906Z19-O
September, 2000
(370 C), and adjust the airow to a minimum setting. Airow can vary due to component density. Chip Component Removal To remove a chip component, select a hot-air hand piece and position the nozzle of the hand piece approximately 1/8 above the component to be removed. Begin applying the hot air. Once the solder reflows, remove the component using a pair of tweezers. Using solder wick and a soldering iron or a power desoldering station, remove the excess solder from the pads. Chip Component Replacement To replace a chip component using a soldering iron, select the appropriate micro-tipped soldering iron and apply fresh solder to one of the solder pads. Using a pair of tweezers, position the new chip component in place while heating the fresh solder. Once solder wicks onto the new component, remove the heat from the solder. Heat the remaining pad with the soldering iron and apply solder until it wicks to the component. If necessary, touch up the first side. All solder joints should be smooth and shiny. To replace a chip component using hot air, select the hot-air hand piece and reow the solder on the solder pads to smooth it. Apply a drop of solder paste ux to each pad. Using a pair of tweezers, position the new component in place. Position the hot- air hand piece approximately 1/8 above the component and begin applying heat. Once the solder wicks to the component, remove the heat and inspect the repair. All joints should be smooth and shiny.
OMPAC Removal To remove the OMPAC, select the R-1319A Air-Flow Station and the appropriate heat- focus head (approximately the same size as the OMPAC. Attach the heatfocus head to the chimney heater. Adjust the temperature control to approximately 415 F (215 C) 445 F (230 C) maximum. Adjust the airflow slightly above the minimum setting. Apply the solder paste flux around the edge of the OMPAC. Place the circuit board in the R-1070A's circuit board holder, and position the OMPAC under the heat-focus head. Lower the vacuum tip and attach it to the OMPAC by turning on the vacuum pump. Lower the heat-focus head until it is approximately 1/8 (0.3cm) above the carrier. Turn on the heater and wait until the OMPAC lifts off the circuit board. Once the part is off, grab it with a pair of tweezers and turn off the vacuum pump. Remove the circuit board from the R-1070A's circuit board holder. OMPAC Replacement To replace the OMPAC, the solder pads on the board must rst be cleaned of all solder to ensure alignment of the new chip carrier. Prepare the sight by using solder wick and a soldering iron to remove all solder from the solder pads on the circuit board. If a power desoldering tool is available, it can be used instead of the solder wick. Clean the solder pads with alcohol and a small brush. Dry and inspect. Ensure that all solder is removed. Once the preparation is complete, place the circuit board back in the R-1070A's circuit board holder. Add solder paste flux in the trench of the flux block and spread it using a one-inch putty knife. Flux the OMPAC by placing it in the trench of the flux block. Once the ux is applied, place the OMPAC on the circuit board, making certain that it is oriented correctly on the board. Position the heat-focus head over the OMPAC and lower it to approximately 1/8 (0.3cm) over the carrier. Using the same heat and airflow setting used to remove the OMPAC, turn on the heater and wait for the carrier to reflow (heating and reflow should take longer than 60 seconds). Once the carrier reows, raise the heat-focus head and wait approximately one minute for the part to cool. Remove the circuit board and inspect the repair. No cleaning should be necessary.
Over-Molded Pad-Array Carrier (OMPAC)

ASFIC U0201 is an OMPAC. It must be kept in a sealed bag with dessicant in the bag (in a dry box as supplied by the Motorola Parts Department prior to use. If the OMPAC is ambient for an unknown amount of time or for more than 96 hours, then it must be baked for at least eight hours at 260 F (185 C). If neighboring OMPAC components are heated above 365 F (185 C), they will suffer die-bond delamination and possible popcorn failure. During all repair procedures, heating neighboring components can be minimized by: Using upper heat only. using the correct size heat-focus head, approximately the same size as the carrier being replaced. Keeping the heat-focus head approximately 1/ 8 (0.3cm) above the printed circuit board when removing or replacing the device.
Shields
Removing and replacing the shields will be done with the R-1070A, using the same heat and airflow profile used to remove and replace OMPAC components. Shield Removal Place the circuit board in the R-1070A's holder. Select the proper heat focus head and attach it to the heater
September, 2000
6880906Z19-O
2-3
Basic Maintenance Repair Procedures and Techniques chimney. Add solder paste ux around the base of the shield. Position the shield under the heat-focus head. Lower the vacuum tip and attach it to the shield by turning on the vacuum pump. Lower the focus head until it is approximately 1/8(0.3cm) above the shield. Turn on the heater and wait until the shield lifts off the circuit board. Once the shield is off, turn off the heat, grab the part with a pair of tweezers, and turn off the vacuum pump. Remove the circuit board from the R1070A's circuit board holder. Shield Replacement To replace the shield, add solder to the shield if necessary, using a micro-tipped soldering iron. Next, rub the soldering iron tip along the edge of the shield to smooth out any excess solder. Use solder wick and a soldering iron to remove excess solder from the solder pads on the circuit board. Place the circuit board back in the R-1070A's circuit board holder. Place the shield on the circuit board using a pair of tweezers. Position the heat-focus head over the shield and lower it to approximately 1/8 above the shield. Turn on the heater and wait for the solder to reow. Once complete, turn off the heat, raise the heatfocus head, and wait approximately one minute for the part to cool. Remove the circuit board and inspect the repair. No cleaning should be necessary.
Thermal compound, 1180382B13.
Motorola
Part
No.
Transistor assembley tool 0293. 1. Remove main board from radio chassis following procedure provided in Section 6 of this service manual, Motorola Publication 6880906Z19. After main board is removed from radio chassis, clean off thermal paste from all surfaces that have thermal paste on them using low lint wipers.
2.
Removing Faulty Transistor 1. Before removing faulty transistor, observe carefully how ange capacitors C6567 and C6568 are mounted. This will help you later in mounting new capacitors. Set hot air gun for medium temperature and low air speed. This will ensure that other components in vicinity of Q6505 will not get dislodged and moved accidently. Train hot air gun on anges of transistor. After a few moments, the solder holding anges will reow enabling transistor and ange capacitors C6567 and C6568 to be lifted off main board together.
2.
3.
Replacement of Transistor Q6505

This section provides a replacement procedure for Q6505, the RF power output transistor in the 30-Watt power amplier. To replace Q6505, proceed as follows: Before proceeding, ensure that the following tools and materials are on hand: Alcohol (isopropyl). High temperature solder, SN96AG04 composition. Motorola Part No. 1180433L04. Hot air gun (600 degrees maximum temperature). Low lint wipers. Soldering station including a soldering iron with chisel-style tip which is approximately 1/ 8-inch in size. Solder ux. Solder wick. 4. Stiff brush, natural bristles approximately 1-cm high and 1-cm wide. 3. 2. 1.
Preparing Main Board for New Transistor Using solder wick, isopropyl alcohol, and stiff bristle brush, remove excess solder and clean pads on main board where transistor was soldered. Place main board, with its heavy side up, on transistor assembly tool. Heavy side is side with PA module and antenna connector. Make certain that all guide pins on transistor assembly tool are engaged into their corresponding holes in main board. Identify the six pads on main board corresponding to the six anges on transistor. The four corner pads are ground; the middle pad towards antenna connector is the transistor collector; and the opposite middle pad is the transistor emitter. NOTE In next step, be certain to tin transistor pads and ll via holes with high temperature solder, composition SN96PB04. Using solder iron, carefully tin each of the six pads so that they are covered with a thin coat of solder and all via holes are lled.
2-4
6880906Z19-O
September, 2000
Positioning New Transistor 1. Place a small spot of ux on each of the six main-board pads to which the anges of transistor are to be soldered. Insert the narrow-diameter side of a spacer, Motorola Part Number 4380545K01, into each of the two transistor mounting holes in main board. Ensure that new transistor is correct replacement type by verifying that M25C20 is printed on transistor face. NOTE Collector flange of transistor is the one with its corner cut off. 4. Position new transistor onto transceiver board with collector ange oriented towards antenna connector. Ensure that transistor is sitting snug on main board with all six anges at on their corresponding main-board pads. Lower arm of Distaco clamp on transistor assembly tool. Then lock clamp with its lever to clamp transistor in place on main board.
Installing Flange Capacitors C6567 and C6568. NOTE Capacitors C6567 and C6568 get mounted flat on transistor collector and ground anges with non-solderable edge ush against transistor body. Each capacitor is attached by soldering its outside solderable edge to one of the transistor ground flanges and its inside solderable edge to transistor collector ange. There must be a gap of approximately 2 millimeters between the two capacitors (i.e., room to insert a chisel style solder iron tip) to ensure that good solder joints can be made between capacitor leads and collector ange of transistor. 1. Ensure that both capacitors C6567 and C6568 are correct replacement type by verifying that Motorola Part Number is 2113742B23, value is 12pF, and marking is Cl. CAUTION In next two steps, to avoid damage to transistor and capacitors, ensure that soldering operations take no more than three to four seconds to accomplish. 2. Solder outside solderable edge of each capacitor to one transistor ground ange, being certain that each capacitor is at on transistor ange with non-solderable edge ush against transistor body. Place a small drop of ux on transistor collector ange between capacitors. Place chisel style solder iron tip between capacitors and onto collector ange of transistor. Feed in some high temperature solder (SN96PB04) so that inside solderable edges of both capacitors are soldered securely to collector ange of transistor. Examine soldered capacitors. Ensure that they are reasonably ush against transistor body and are not shorting transistor collector ange to transistor heat sink. Examine surrounding components to ensure that none of them have been damaged or displaced.
2.
3.
5.
Soldering Transistor 1. Place a small spot of ux on each of the six transistor anges. 3. 2. 2. Solder each transistor ange to transceiver board as follows:
2A. Set soldering iron temperature to approximately 400 degrees Centigrade. 2B. Melt a small mound of solder onto at face of soldering iron.
4.
CAUTION In next step, to avoid damage to transistor and capacitors, ensure that each soldering operation takes no more than three to four seconds to accomplish. 3. Press face of soldering iron rmly to ange for no more than three to four seconds. Inspect transistor ange carefully to ensure it is soldered securely, and that it is not shorted to any of the other anges or to the transistor heat sink.
5.
Reassembly of Radio 1. Examine face of transistor heat sink. Ensure that it is free from burrs and ux, which could prevent a good thermal contact to radio chassis.
4.
September, 2000
6880906Z19-O
2-5
Basic Maintenance Repair Procedures and Techniques 2. Spread thermal compound on heat sink of the following components:
+9.3V voltage regulator U601
Transistor Q6505 PAmoduleU6501 Audio PA module U401
3.
Install transceiver board into radio chassis following procedure provided in Section 6 of this service manual, Motorola Publication 6880906Z19.
2-6
6880906Z19-O
September, 2000
Section 3 Test Equipment, Service Aids, and Tools
Test Equipment
The list in Table 3-1 includes all standard test equipment required for servicing two-way mobile radios. Batteryoperated test equipment is recommended when available. The Characteristics column is included so that equivalent equipment may be substituted; however, when no information is provided in this column, the specic Motorola model listed is either a unique item or no substitution is recommended. Table 3-1. Model No. R2000 Series with trunking option R1053 Description Communications System Analyzer Recommended Test Equipment Characteristics Application Frequency/deviation meter and signal generator for wide-range troubleshooting and alignment 200 MHz bandwidth, For waveform measurements
Dual Trace Oscilloscope Digital Multimeter Load resistor RF Millivolt Meter 10 kHz to 1.2 GHz DC Power Supply
FLUKE 8012 T1013A S1339A
AC/DC voltage and current meter 0-1000MHz, 300 W 100 V to 3V rf For use with wattmeter RF level measurements
R1011B
0-40Vdc, 30 Amps
Bench supply for 13.8Vdc current limited
September, 2000
6880906Z19-O
3-1
Test Equipment, Service Aids, and Tools Field Programming
Field Programming
The radio can be aligned and programmed in the eld. This requires specic equipment and special instructions. refer to the Radio Service Software Users Manual for complete eld programming information. Table 3-2. Part No. RLN4008B Description Radio Interface Box Service Aids Application Enables communications between the radio and the computers serial communications adapter. Used to supply power to the RIB (240 VAC). Used to supply power to the RIB (220 VAC). Used to supply power to the RIB (110 VAC). Connects radio to RLN4008B RIB. Interconnects radio to power supply. Interconnects radio to power supply.
EPN4040A 0180358A56 0180357A57 3080070N01 GKN6270A HKN4191B
Power Supply Power Supply 110V AC-to-DC Adapter Combined Interface Cable DC Power Cable for radio 35 W Power Cable for radio Computer Interface Cable
3080369B72
Connects the computers serial communications adapter (9 pin) to the RIB. Connects the computers serial communications adapter (25 pin) to the RIB. 25 pin (F) to 9 pin (M) adapter, for use with 3080369B72 for AT applications. For GTX radio programming.
3080369B71
Computer Interface Cable
RLN4438A
Adapter
RVN4150B
Radio Service Software (RSS) GTX (RSS) Radio Service Software Manual Test Fixture Test Cable
68P02948C70
Provides detailed instruction on RSS used in GTX radios. For radio testing For connecting between the radio and RLN4460A.
RLN4460A 3008566C12
3-2
6880906Z19-O
September, 2000
Test Equipment, Service Aids, and Tools Service Tools
Service Tools
The following table lists the tools recommended for working on the radio; these are also available from Motorola. Note that the R-1070A workstation requires the use of a specic heat focus head for each of the components on which this item is used. Each of these heat focus heads must be ordered separately. Table 3-3. Part No. 0180381B45 110 VAC or 0180300E06 220 VAC 8180369E97 Description MBT250 Surface-mount/ through-hole repair station Flux holder/applicator Service Tools Application Temperature-controlled, self-contained soldering/desoldering repair station for installation and removal of surface-mounted devices. Allows for the proper amount of ux to be applied to pad grid arrays for repair. For use with ux holder/applicator 8180369E97.
1105139W02
30cc plastic syringe and ux paste Miniature digital readout soldering station (includes 1/64 micropoint tip) Illuminated magnifying glass with lens attachment Anti-static grounding kit
0180386A81
0180386A78
0180386A82
Used during all radio assembly and disassembly procedures
6684253C72 6680384A98 1010041A86
Straight prober Brush Solder (RMA type), 63/37, 0.020 diameter, 1 lb. spool Shields and surfacemounted component - IC removal/rework station Surface-Mounted Device Rework Station R1319A Reow Nozzle R1319A Reow Nozzle R1319A Reow Nozzle R1319A Reow Nozzle Transmitter Assembly Tool Removal of surface-mounted integrated circuits
R-1070A (superseded by R1319A)
R1319A 6680332E82 6680332E83 6680332E84 6680333E28 0293
Removal of surface-mounted integrated circuits For IC removal (approximate size 0.8 in. x 0.8 in.) For IC removal (approximate size 0.6 in. x 0.6 in.) For IC removal (approximate size 0.5 in. x 0.5 in.) For removal of RF PA Replacement for transisator Q6505
September, 2000
6880906Z19-O
3-3
Test Equipment, Service Aids, and Tools Service Tools
3-4
6880906Z19-O
September, 2000
Section 4 Test Mode, Error Codes and Performance Tests
Front Panel Test Mode

The functions of the radio controls for the Front Panel Test Mode are as follows:
One beep is heard to indicate operation on the rst test frequency (default). Display shows "4 1" .
CHANNEL MODE (4 IS INITIAL MODE)
Test Mode/Entry
Test Mode allows radio checks to be performed in the eld. To provide a level of protection to the Test Mode entry, proceed according to the following sequence: 1. Place radio in TRUNKING operation mode and wait for 6 seconds. (See Quick Start card for instructions on how to enter that mode.) Turn radio off. Verify that RIB is off. Turn radio power supply (13.6 V DC) on . Turn radio on.
Test Mode/Channel Selection

Use the PTT switch for channel selection. A short press and de-press on the PTT switch (button-like push) will advance the radio to the next channel (cyclical) . Seven channels are available during test mode, as shown in Table 4-1.
2. 3. 4. 5.
Test Mode/Tx Modulation

Use PTT switch for modulation type selection. A continuous press will advance the radio to the next modulation test (cyclic scroll ) and perform Tx test until PTT is released. The modulation selection is described in Table 4-2.
The radio enters Test Mode operation: Speaker unmutes.
Channel Number 1 2 3 4 5 6 7 1. 2.
Table 4-1. Test Mode/Channel Selection Rx Frequency Tx Frequency 935.0125 MHz 941.9875 MHz 938.5125 MHz CC1 (1) CC2 (1) CC3 (1) CC4 (1) 896.0125 MHz 901.9875 MHz 899.5125 MHz CC1-45 MHz CC2-45 MHz CC3-45 MHz CC4-45 MHz
Display M 1 (2) M 2 (2) M 3 (2) M 4 (2) M 5 (2) M 6 (2) M 7 (2)
CC1-CC4 are control channels programmed in association with the selected trunking system. M stands for modulation type (0-3). See Table 4-2. Table 4-2. Test Mode/Tx Modulation Internal Speaker Audio Signaling Internal Microphone Status None Busy Channel Call Back DTMF # On On Off Off
Modulation Type CSQ Low Speed High Speed DTMF # 1.
Display 0 C (1) 1 C (1) 2 C (1) 3 C (1)
C stands for the selected channel (1-7). See Table 4-1.
September, 2000
6880906Z19-O
4-1
Test Mode, Error Codes and Performance Tests Front Panel Test Mode
Fail Mode
The radio will enter Fail Mode upon detecting one of the following errors: Application startup self check error Codeplug information check error
There are two categories of errors: critical and non-critical. Critical errors will stop radio normal operation. Refer to Table 4-3.
Exiting Test Mode

To exit Test Mode, proceed as follows: Turn radio off. Turn RIB on.
Error number 1 2 5 6 7 (1)
Table 4-3. Fail Mode Failure Description Display Critical Internal RAM External RAM OTP checksum Codeplug checksum Codeplug personality F 01 F 02 F 05 E 06 E 06 Yes Yes Yes Yes No
Tone Sound Illegal tone Illegal tone Illegal tone Illegal tone Illegal Tone (when selected personality has checksum error) Ilegal tone
8 1.
Codeplug tuning error
E 06
Yes
For error no. 7, personality (system) change is allowed although the illegal tone is heard. For error no. 8 the temporary illegal tone is heard. (See the Quick Start card for instructions on how to change personality.) To exit fail mode, power radio off. Non-critical errors will be temporarily indicated as described in Table 4-2.
Test Name Reference Frequency
Table 4-4. Communication Analyzer
Transmitter Performance Checks Radio Test Set Comments
Mode: PWR MON TEST MODE, Dis- PTT to continuous Frequency error to be 2nd channel test frequency play: 2 0 (during the perfor- < 700 Hz Monitor. Frequency error inmance check) put at RF In/Out Same as Above TEST MODE, Display: 2 0 Same as Above Same as Above, meter selector to mic Refer to Maintenance Specication page x Deviation: 800 MHz: 3.6 kHz but 5.0 kHz 900 MHz: 2.5 kH
Power RF Voice Modulation
Mode: PWR MON TEST MODE, 4th channel test frequency Display: 2 0 atten to -70, input to rf In/ Out Monitor: DVM, AC Volts Set 1kHz mod Out level for 0.025Vrms at test set, 80mVrms at AC/DC test set jack. TEST MODE, Display: 2 1
Low-Speed Data Same as Above Modulation 800/900
PTT to continuous Deviation: (during the perfor- 800 MHz: mance check) 800 Hz but 1200 Hz 900 MHz: 350 Hz 650 Hz
4-2
6880906Z19-O
September, 2000
Test Name Voice Modulation (Internal)
Table 4-4. Transmitter Performance Checks (Cont'd.) Communication Analyzer Radio Test Set Mode: PWR MON 2nd channel test frequency atten to -70, input to RF In/ Out TEST MODE, Display: 2 0 Remove modulation input
Comments Press PTT switch on radio. Say four loudly into the radio mic. Measure deviation: 800 MHz: 3.8 kHz but 5.0 kHz 900 MHz: 2.5 kHz
High-Speed Data Modulation
Same as Above
TEST MODE, Display: 2 2
PTT to continuous Deviation: (during the perfor- 800 MHz: mance check) 2.3 kHz but 3.8 kHz 900 MHz : 1.2 kHz but 2 kHz Deviation: 800 MHz: 2.8 kHz but 3.8 kHz 900 MHz : 1.4 kHz but 1.9 kHz Deviation: 800 MHz: 500 Hz but 1000 Hz 900 MHz: 250 Hz but 500 Hz Deviation: 800 MHz: 3.8 kHz but 5.0 kHz 900 MHz : 1.9 kHz but 2.45 kHz
DTMF Modula- Same as Above tion 2nd channel test frequency (# SIGN)
TEST MODE, Dis- Same as Above play: 2 3 output at antenna
PL/DPL Modu- Change frequency to a lation (radios conventional transmit with convenfrequency, BW to narrow tional coded squelch operation only) Talk-around Modulation (radios with conventional talkaround operation only)
Conventional coded squelch personality
Same as Above
Change frequency to conven- Conventional tional talk-around frequency. talk-around perMode:PWR MON sonality deviation, attenuation to -70, input to RF In/Out Monitor: DVM, AC volts Set 1kHz Mod Out level for 25mVrms at test set.
Same as Above
Test Name Rated Audio
Table 4-5. Communication Analyzer Mode: GEN Output level: 1.0mV RF 1st Channel test frequency Mod: 1 kHz tone at 3 kHz deviation Monitor: DVM: AC Volts
Receiver Performance Checks Radio TEST MODE, Channel 0 Modulation Type 1 Test Set PTT to OFF (center), meter to Audio PA Comments Set volume control to 3.74 Vrms
Distortion Sensitivity (SINAD)
Same as above, except for distortion
Same as Above
Same as Above PTT to OFF (center)
Distortion <5.0% RF input to be <0.35 V
Same as above, except SINAD, Same as Above lower the rf level for 12 dB SINAD
September, 2000
6880906Z19-O
4-3
Test Name Noise Squelch Threshold (only radios with conventional system need to be tested
Table 4-5. Receiver Performance Checks (Cont'd.) Communication Analyzer Radio Test Set RF level set to 1mV RF Same as Above
Comments
PTT to OFF (center), Set volume conmeter selection to Au- trol to 3.74 Vrms dio PA, spkr/load to speaker Unsquelch to occur at <0.3 V Preferred SINAD=<12 dB
As above, except change frequency to a conventional system. Raise RF level from Zero until radio unsquelches.
out of TEST Same as Above MODE, select a conventional system
4-4
6880906Z19-O
September, 2000
Section 5 Disassembly & Reassembly For 12 W Models
Introduction
This chapter explains, step by step, how to disassemble and assemble the radio, to board level.
Disassemble the Radio

Remove the Control Head
1. 2. Turn the radio upside down. Insert a small at blade screw driver, or similar, in the recess between the control head and the chassis. Refer to Figure 5-1. Press until the side of the control head releases. Pull the control head away from the radio. Remove the speaker pad and at cable from the connector on the radio side. Refer to Figure 5-2 and Figure 5-6.
CONTROL HEAD RECESS
3. 4. 5.
Figure 5-2.
Flat Cable Removal
SIDE RECESS
Figure 5-1.
Control Head Removal
Remove the Top Cover

1. 2. 3. 4. Turn the radio upside down. Insert a small flat bladed screw driver in the side recesses between the cover and the chassis. Tilt the cover until the side snaps off the latch. Repeat the operation on the opposite side of the radio.
6880906Z19-O
Figure 5-3.
Top Cover Removal
5. 6.
Turn the radio right side up. Lift the top cover over the chassis. 5-1
September, 2000
Disassembly & Reassembly For 12 W Models Disassemble the Radio
Remove the Main Board

1. Remove the 3 screws of the PA shield using a T8 TORX driver. Remove the PA shield by gently prying up each corner of the shield. Remove the power and antenna connector retaining clips by inserting a small at blade screw driver between the clip and the top of the chassis wall and gently prying the clip upwards. Pull out the accessory clamp and connector gasket. Pull out the accessory kit. Remove the 8 screws securing the main board to the chassis. Carefully remove the main board by rotating it out of the chassis. Slowly lift the board on the front edge, the side with the connector that mates with the control head, and pull gently toward the front of the radio. CAUTION The thermal grease can act as an adhesive and cause the leads of the heat dissipating devices to be over stressed if the board is lifted too quickly. 2. 3. Figure 5-4. Main Board Removal
SHIELD CLIPS
2.
3. 4. 5. 6. 7.
truding tabs. Remove the board from the control head housing. Disconnect the speaker from the board by removing it from the socket. Remove the keypad from the control head housing by lifting it up from the board. Care should be taken not to touch or get other contaminates on the conductive pads on the under side of the keypad or conductive contacts on the printed circuit board. Take the LCD frame out of the control head.
Disassemble the Control Head

1. To pull out the circuit board from the control head housing, insert a small bladed screw driver in the side groove near the four proHOUSING
4.
PART OF LCD FRAME
SPEAKER VOLUME KNOB
LCD FRAME ZEBRA CONNECTOR
TAB
KEYPAD POTENTIOMETER
FLAT CABLE
Figure 5-5. 5-2

6880906Z19-O September, 2000
Disassembly & Reassembly For 12 W Models Assemble the Radio
Assemble the Radio

Assemble the Control Head
3.
Install the 8 screws with 0.4 -07 NM (4-6 in lbs) of torque using a T8 TORX driver. Before installing the connector retaining clips, ensure that the board is sitting ush on the chassis mounting surface. Install the PA shield and secure it with 3 screws.
4. 1. 2. Insert the LCD frame with LCD and Zebra connectors into its place. Place the keypad onto the board assembly, making sure the keypad is ush with the board. Rotate the potentiometer counterclockwise. Rotate the volume knob counterclockwise. This will allow you to insert the potentiometer smoothly into its place in the volume knob. Make sure the speaker including the gasket is well positioned into the pocket of the housing.. Connect the speaker to the circuit board. During the installation of the circuit board, ensure the four protruding tabs snap into the recesses. 2. 5.
3.
Replace the Top Cover and Control Head

1. Position the top cover over the chassis and replace. Ensure that the chassis crosses snap into the covers openings. Connect the at cable to the connector on the radio. Assemble the speaker pad by sliding the slit of the pad over the at cable. Refer to Figure 5-6. Push the speaker pad onto the chassis. Press the control head onto the chassis until the protruding taps on the chassis snap into the recesses inside the housing.
4.
5. 6.
3.
Replace the Main Board

1. 2. Inspect and if necessary, reapply thermal grease to the heatsinking pads in the chassis. Rotate the main board into the chassis and ensure that the board is ush to the chassis. 4. 5.
Figure 5-6.
September, 2000
6880906Z19-O
5-3
5-4
6880906Z19-O
September, 2000
Section 6 Disassembly & Reassembly For 30 W Models
Introduction
This chapter explains, step by step, how to disassemble and assemble the radio, to board level.
Disassemble the Radio

Remove the Control Head
1. 2. Turn the radio upside down. Insert a small at blade screw driver, or similar, in the recess between the control head and the chassis. Refer to Figure 6-1. Press until the side of the control head releases. Pull the control head away from the radio. Remove the speaker pad and at cable from the connector on the radio side. Refer to Figure 6-2 and Figure 6-7.
CONTROL HEAD RECESS
3. 4. 5.
Figure 6-2.
Flat Cable Removal
SIDE RECESS
Figure 6-1.
Remove the Top Cover

1. 2. 3. 4. Turn the radio upside down. Insert a small flat bladed screw driver in the side recesses between the cover and the chassis. Tilt the cover until the side snaps off the latch. Repeat the operation on the opposite side of the radio.
6880906Z19-O
Figure 6-3. 5. 6.
Top Cover Removal
Turn the radio right side up. Lift the top cover over the chassis. 6-1
September, 2000
Disassembly & Reassembly For 30 W Models Disassemble the Radio
Remove the Main Board

1. Remove the 4 screws of the PA shield using a T8 TORX driver. CAUTION The PA shield has sharp edges. Handle with care when removing and replacing. 2. Remove the PA shield as follows:
CLIP SHIELD
2A. Hold the shield handle with your index and middle ngers while pressing your thumb downward on the shield. Keep all ngers curled upward as shown in Figure 6-4.
Figure 6-5. 7. 8. 9.
Main Board Removal
Remove the 14 screws securing the main board to the chassis. Carefully remove the main board by rotating it out of the chassis. Slowly lift the board on the front edge, the side with the connector that mates with the control head, and pull gently toward the front of the radio. CAUTION The thermal grease can act as an adhesive and cause the leads of the heat dissipating devices to be over stressed if the board is lifted too quickly.
Figure 6-4. 2B.
Shield Removal
Keeping the other hand away from the PA shield, place your thumb on top of the front of the radio while placing your ngers underneath the chassis. Refer to Figure 6-4. Make sure this hand is away from the PA shield.
Disassemble the Control Head

1. To pull out the circuit board from the control head housing, by inserting a small bladed screw driver in the side groove near the four protruding tabs. Remove the board from the control head housing. Disconnect the speaker from the board by removing it from the socket. Remove the keypad from the control head housing by lifting it up from the board. Care should be taken not to touch or get other contaminates on the conductive pads on the under side of the keypad or conductive contacts on the printed circuit board. Take the LCD frame out of the control head.
2C. Holding the chassis rmly, remove the PA shield by pulling upward on the handle. 3. Remove the antenna connector retaining clip by inserting a small at bladed screw driver between the clip and the top of the chassis wall and gently prying the clip upwards. Pull out the accessory clamp and connector gasket. Pull out the accessory kit. Twist the sleeve of the power cable 90 degrees and lift up and out from the chassis. 4. 2. 3. 4. 5. 6.
6-2
6880906Z19-O
September, 2000

HOUSING PART OF LCD FRAME
SPEAKER VOLUME KNOB
LCD FRAME ZEBRA CONNECTOR
TAB
KEYPAD POTENTIOMETER
FLAT CABLE
Figure 6-6.
Control Head Removal 5. Install the PA shield and secure it with the 4 screws.
Assemble the Radio

Assemble the Control Head
1. 2. Insert the LCD frame with LCD and Zebra connectors into its place. Place the keypad onto the board assembly, making sure the keypad is ush with the board. Rotate the potentiometer counterclockwise. Rotate the volume knob counterclockwise. This will allow you to insert the potentiometer smoothly into its place in the volume knob. Make sure the speaker is well positioned into the pocket of the housing. Connect the speaker to the circuit board. During the installation of the circuit board, ensure the four protruding tabs snap into the recesses.
Replace the Top Cover and Control Head

1. Position the top cover over the chassis and replace. Ensure that the chassis crosses snap into the covers openings. Connect the at cable to the connector on the radio. Assemble the speaker pad by sliding the slit of the pad over the at cable. Refer to Figure 6-7. Push the speaker pad onto the chassis. Press the control head onto the chassis until the protruding taps on the chassis snap into the recesses inside the housing.
2. 3. 4. 5.
3.
4. 5. 6.
Replace the Main Board

1. 2. 3. 4. Inspect and if necessary, reapply thermal grease to the heatsinking pads in the chassis. Rotate the main board into the chassis and ensure that the board is ush to the chassis. Install the 14 screws with 0.4 -07 NM (4-6 in lbs) of torque using a T8 TORX driver. Before installing the connector retaining clip and power cable, ensure that the board is sitting ush on the chassis mounting surface.
6880906Z19-O
Figure 6-7.
September, 2000
6-3
6-4
6880906Z19-O
September, 2000
Section 7 Radio Tuning Procedure
Radio Tuning Procedure

General
An IBM PC (personal computer) and RSS (Radio Service Software) are required to align the radio. Refer to the applicable RSS Manual for installation and setup procedures for the software. To perform the alignment procedures, the radio must be connected to the PC, RIB (Radio Interface Box), and Test Set as shown in Figure 7-1.
CAUTION Do NOT switch radios in the middle of any SERVICE procedure. Always use the EXIT key to return to the MAIN menu screen before disconnecting the radio. Improper exits from the SERVICE screens may leave the radio in an improperly congured state and result in seriously degraded radio or system performance. The SERVICE screens use the concept of the Softpot, an analog SOFTware controlled POTentiometer used for adjusting all transceiver alignment controls. Each SERVICE screen provides the capability to increase or decrease the softpot value with the keyboard UP/DOWN arrow keys respectively. A graphical scale is displayed indicating the minimum, maximum, and proposed value of the softpot, as shown in Figure 7-3.
Service Menu
Figure 7-2 illustrates the Main Service Menu structure. All SERVICE screens read and program the radio codeplug directly; you do NOT have to use the RSS GET/ SAVE functions to program new tuning values.
30 dB PAD TRANSMIT 30 dB PAD BNC RF GENERATOR Mini-U BNC 58-80348B33 RECEIVE
SERVICE MONITOR or COUNTER
WATTMETER
AUDIO IN MIC IN RADIO TEST CABLE 3008566C12 Note: Battery can be used in RIB making power supply optional. PROGRAM or TEST CABLE 3080070N01 25-PIN RIB RLN4008B 15-PIN TEST SET RLN4460A
TX RX
AUDIO GENERATOR SINAD METER AC VOLTMETER
COMPUTER DATA GND
COMPUTER INTERFACE CABLE 30-80369B72 (IBM AT, 9-PIN ONLY) 30-80369B71 (IBM XT, 25-PIN ONLY) RIB POWER SUPPLY 0180357A57, 110 V, USA 0180358A56, 110 V, USA
Figure 7-1.
Radio Alignment Test Setup 7-1
September, 2000
6880906Z19-O
Radio Tuning Procedure Tuning Procedure

Service Menu
F2 Alignment Menu
F6 Board Replacement Menu F2 Logic or RF Board Replacement F3 Tx Power F4 Warp Reference Frequency F5 Tx Power Calibration F6 Tx Deviation Calibration F9 Squelch Adjustment
F3 Deviation Adjustment F5 Reference Oscillator Warp F7 Transmitter Power F8 Squelch Adjustment
Figure 7-2.
Service Menu Structure
4. 0 15
Press F6 again to dekey the radio, and then press F8 to program the softpot value.
Reference Oscillator Alignment

Min. Value Max. Value
MAEPF-22858-O
NOTE The frequency of the transmitter must be checked on installation and at least annually. Adjustment of the reference oscillator is critical for proper radio operation. Improper adjustment will not only result in poor operation, but also a misaligned radio that will interfere with other users operating on adjacent channels. For this reason, the reference oscillator should be checked every time the radio is serviced. The frequency counter used for this procedure must have a stability of 0.1 ppm (or better). 1. 2. 3. 4. 5. Press F4 to select the REFERENCE OSCILLATOR softpot. Press F6 to key the radio. The screen will indicate that the radio is transmitting. Measure the transmit frequency that appears on the screen of your frequency counter. Use the UP/DOWN arrow keys to adjust the reference oscillator. Press F6 again to dekey the radio and then press F8 to program the softpot value.
Figure 7-3.
Softpot Concept
Tuning Procedure
Starting the Tuning Procedure
1. 2. From the SERVICE menu, press F6 to select BOARD REPLACEMENT. Press F2 for LOGIC OR RF BOARD replacement. NOTE Perform the following procedures in the sequence indicated.
Alignment Default Data

1. 2. Press F2 to select ALIGNMENT DEFAULT DATA. Press F8 for PROGRAM VALUE.
Tx Power
1. 2. 3. Press F3 to select Tx POWER. Press F6 to key the radio. The screen will indicate that the radio is transmitting. Adjust the transmit power value with the UP/ DOWN arrow keys.
Transmitter Power
NOTE During Tx POWER tuning, measure and note the DC transmit current (ITx ) for each channel in the high power band.
7-2
6880906Z19-O
September, 2000
Radio Tuning Procedure Tuning Procedure
1.
Press F5 to select the Tx POWER calibration softpot. The screen will indicate the transmit test frequencies to be used. Press F6 to key the radio. Use the UP/DOWN arrow keys to adjust the transmit power value. Press Enter to select next softpot frequency.
1.
Press F6 to select TX DEVIATION CALIBRATION. The screen will indicate the transmit test frequencies to be used. Begin with the lowest test frequency shown on the screen. Press F6 to key the radio. Record this measurement. Press F4 to select 2.5 kHz. Use the UP/DOWN arrow keys to adjust the deviation to within 0.5 dB of the value recorded in step 3. Press Enter to move to next softpot value. Repeat steps 5 and 6 for the remaining frequencies. Press F8 to program the softpot value.
2. 3. 4. 5. 6. 7.
2. 3. 4.
Repeat steps 3 and 4 for the remaining test frequencies. Press F6 to dekey the radio. Press F8 to program the value.
5.
6. 7. 8.
Transmit Current Limit

NOTE Larger Softpot values yields increased CUTBACK resulting in LOWER POWER. 1. After Tx POWER tuning the TRANSMIT CURRENT LIMIT screen will appear. Select the frequency with the highest DC transmit current (ITx) measured during the Tx POWER tuning procuedure. Press F6 to key the radio. Use the UP/DOWN arrow keys to adjust the DC transmit current value per Table 7-1. Transmit Current Limit Tune Windows Min 4.60 A ITx + 0.4 A Max 5.10 A
Transmit Deviation Limit

The transmit deviation limit softpot sets the maximum deviation of the carrier. Tuning is performed for 12.5 kHz channel spacing. 1. 2. 3. 4. 5. 6. Begin with the lowest test frequency shown on the screen. Press F6 to key the radio. With Test Box 4460A: inject a 1 kHz tone, 2000 mVrms. Use the UP/DOWN arrow keys to adjust the deviation to between 2.2 kHz and 2.4kHz. Press Enter to move to the next softpot value. Repeat steps 4 and 5 for the remaining frequencies shown on the screen. Press F6 to dekey the radio. Press F8 to program the softpot value.
2. 3.
Table 7-1. Model 900_12W 900_30W
ITx + 1.0 A 7.
4. 5.
Press F6 to dekey the radio. Press F8 to program the value.
8.
Squelch
The squelch softpots set the signal to noise ratio at which the squelch opens. 1. 2. 3. Press F9 to select SQUELCH Adjustment. Adjust the UP/DOWN arrow key to the minimum squelch value. Apply a standard RF input level of -47 dBm to the radio on the test frequency.
Transmit Deviation Balance (Compensation) & Deviation Limit

Compensation alignment balances the modulation sensitivity of the VCO and reference modulation (synthesizer low frequency port) lines. Compensation algorithm is critical to the operation of signaling schemes that have very low frequency components (e.g. DPL) and could result in distorted waveforms if improperly adjusted.
September, 2000
6880906Z19-O
7-3
Radio Tuning Procedure Tuning Procedure 4. Adjust the radios volume control to obtain rated audio power at the external speaker of the accessory connector. Reduce the RF input level until 10 dB SINAD is measured. Adjust the UP/DOWN arrow key until the squelch just closes. Monitor for squelch chatter and adjust UP as required. 7.
When no chatter is detected press F8 to program.
5.
Ending the Tuning Procedure

1. 2. Press F2 to continue. Press F10, F10 to return to the Service menu
6.
7-4
6880906Z19-O
September, 2000
Section 8 Theory of Operation
Introduction
This section provides theory of operation information for the radio. It starts with a block diagram level functional description of the entire radio. This is followed by a detailed functional description for each of the four major functions that make up the radio.
The control head is mounted directly on the front of the radio. The control head contains a speaker, LED indicators, a microphone connector and buttons which provide the user with interface control over the various features of the radio and a display. In addition to the power cable and antenna cable, an accessory cable can be attached to a connector on the rear of the radio. The accessory cable provides the necessary connections for items such as external speaker, foot operated PTT, ignition sensing, public address, remote desk set and data modem.
AUDIO & LOGIC
AUDIO PA
Overview
The main radio is a single board design, consisting of the transmitter, receiver, and controller circuits.
RECEIVER MIXER
3-POLE CERAMIC PRE-SELECTOR RF AMP 3-POLE CERAMIC PRE-SELECTOR LO SIGNAL 2-POLE IF BACK-END 2.1 MHZ ASFIC MOD
CPU CLOCK CPU
SPI
MEMORY
DIRECTIONAL COUPLER
KEYBOARD DISPLAY PENDULUM HARMONIC FILTER 16.8 MHZ
RF PA
SYNTHESIZER
FRAC N RX/TX VCO T/R SWITCH PA LINEUP IC
SYNTHESIZER LINEUP
MOD TA VCO LOOP FILTER POWER CONTROL
Figure 8-1.
900-MHz Radio Functional Block Diagram
September, 2000
6880906Z19-O
8-1
Theory of Operation Receiver Detailed Functional Description
Receiver Detailed Functional Description

The receiver is composed of four sections: receiver front end, receiver IF, receiver back end and the Audio Signal Filter IC (ASFIC) that is part of the controller section. The RF signal from the antenna switch in the PA section enters the first bandpass filter (FL5203). The first bandpass filter has three poles, a 938-MHz center frequency, a 6-MHz wide passband and a 35-dB rejection for image frequencies (857 to 863MHz). After the rst bandpass lter, the signal passes to a pair of hot-carrier limiting diodes (D5303) placed in front of RF preamplifier Q5301. The hot-carrier diodes limit strong signals to prevent them from overdriving the RF preamplier and damaging it. The RX front end is a Low Noise Amplier (LNA) that consists of Q5301. Its main purpuse is to set the noise gure of the receiver. The front end amplier as well as the IF amplifiers are shut off during transmit by K9.1 line via switch Q5230, to provide isolation in talkaround mode. After the LNA, the signal enters a second bandpass lter (FL5204), which is identical to FL5203. The bandpass lters are xed tuned from 935 to 941 MHz. After the second bandpass filter, mixer U5211 downconverts the signal to the IF frequency. The mixer is a passive double-balance mixer that gets a local oscillator signal in the range of 895.9 to 901.9 MHz from the synthesizer and works on 4-dBm power. The IF frequency is 45.1 MHz. A diplexer matches the
mixer IF port to 50 Ohm out of the IF frequency band. The diplexer consists of R5401, C5404, L5402. The IF signal is fed to rst crystal lter Y5201 through matching network L5401, C5200. Crystal lter Y5201 has two poles. The crystal lter is followed by matching elements, that match the filter output impedance to the input impedance of IF amplier Q5201. Following the IF amplier is a matching network that matches the IF amplier output impedance to the input impedance of a second 45.1-MHz crystal lter (Y5202). The second crystal filter is followed by matching elements that match the output of the second crystal lter to the input of the receiver back end circuits. After the matching circuit, the signal passes a pair of hot-carrier limiting diodes (D5201) placed in front of the back end circuit. The receiver back end consists of BBR IC (U5201) that contains the following functions: Preamplier & mixer to convert the signal to a second IF frequency of 455 kHz. Second LO circuit Second IF ampliers FM Demodulator Audio amplier In addition to BBR IC, the back end contains the following components: Second LO resonator for 44.645 MHz (Y5211) Crystal lters for 455 kHz (FL5201, FL5202) Demodulator lter (C5224)
BPF 455 kHz LOSS = 6 dB BW = 9 kHz GAIN = 14 dB NF = 2 dB GAIN = 21 dB NF = 3.3 dB IIP3 = 3 dBm
BPF 455 kHz LOSS = 4 dB BW = 12 kHz
LO_INJ
DET_AUDIO PRE-SELECTOR 3 ELEMENTS CERAMIC FILTER LOSS = 2.0 dB REJ = -35 dB @ IMAGE RF AMP PRE-SELECTOR 3 ELEMENTS CERAMIC FILTER LOSS = 2.0 dB REJ = -35 dB @ IMAGE IF BPF CRYSTAL 2-POLE IF AMP IF BPF CRYSTAL 2-POLE LOSS = 2.5 dB REJ = 10 dB @ 12.5KHz 2ND LO 44.654 MHZ K9.1 SW 5 V BBR RSSI
C. LOSS = 7.5 dB LOSS = 2.5 dB REJ = 10 dB @ 12.5KHz NF = 7.5 dB
5V_REG 9V3 ADAPT
Figure 8-2.
Receiver Functional Block Diagram
8-2
6880906Z19-O
September, 2000
Theory of Operation Transmitter Detailed Functional Description
The IF signal routed to BBR IC is amplied, converted to 455 kHz, ltered, limited and demodulated. Demodulated audio comes out of BBR IC at U5201-28 and is fed to the ASFIC, which is part of the radio controller section. In addition to the audio output signal, the receiver section provides an RSSI (Receiver Signal Strength Indicator) at U5201-11. The RSSI signal is fed to the ASFIC and accessory connector. ADAPT signal into U5201-22 controls the BBR IC. The normally low (0 VDC) ADAPT signal is high (5 VDC) during change of radio channels, transition from transmit to receive or at turn-on. The ADAPT signal is used to control precharge of capacitor C5231 at DEMOD_OUT. This is done in order to eliminate the transient during frequency change or when the radio goes from transmit to receive mode.
impedance looking into the transmitter. Therefore, energy coming in the receive mode is channeled to the RX port. Harmonics of the transmitter are attenuated by the harmonic lter. The harmonic lter is formed by inductors L6513 and L6518 as well as capacitors C6540-C6542, C6551-C6553. This network forms a low-pass filter to attenuate harmonic energy of the transmitter to specications level. A forward-power detector follows the harmonic lter. This forward-power detector is a microstrip printed circuit, which couples a small amount of the forward energy and to diode CR6506 where it is rectied. This rectied signal (VFORWARD) forms the forward voltage which the power control circuit holds constant. Holding this voltage constant (which is proportional to the RF rectified energy appearing across the diode) ensures the forward-power out of the radio is held to a constant value. Thermistor R6519 senses temperature in the area of the power module. This signal is fed back into the power control circuit to protect the power amplifier against over-temperature conditions. Resistor R6520, in series with the A+ line supply, feeds voltage to the power module. The voltage across R6520 is monitored and the difference voltage is channeled to the power control circuit. The power control circuit monitors the voltage drop across the resistor which is determined by the magnitude of the drain current in U6501. It uses this as a limiting mechanism whereby the power control circuit limits the magnitude of current that can be drawn by U6501. This protects the device from over dissipation. Bias voltage reverse polarity protection for the transmitter is provided by diode CR6508. Under reverse polarity conditions to the radio, this diode conducts and protects the radio from damage. This diode also provides transient over-voltage protection by breaking down when the supply voltage to the radio exceeds 24 V.
Transmitter Detailed Functional Description

12 Watt PA
The 12-W PA is a three-stage radio frequency (RF) power amplifier used to amplify the output from the TX injection lineup to the radio transmit level. It consists of driver stage Q6501 followed by a two-stage power module U6501. The two stages of the power module operate from the A+ supply voltage. The module is switched on/off by the K9.1 line through switch U6502 (which connects the A+ line to pin 2 of U6501 when transmit is enabled). The RF drive, which is routed into transistor Q6501, is controlled from Q6506 via the PA control line. The rising control voltage on the PA control line causes a rising collector voltage on Q6501. This causes more power out of the stage. Conversely, a decreasing control line voltage decreases the power delivered into the next stage. By controlling the drive power to U6501 and the following stages in the power amplier lineup, ALC loop is able to regulate the output power of the transmitter. The antenna switch is switched synchronously with the keyed 9.1 voltage. In the transmit mode, this 9.1 voltage is highturning on diodes CR6502, CR6503 and CR6504. When CR6502 is turned on, it forms a low impedance to the RF transmit path and allows the signal to pass through. Diodes CR6503 and CR6504 short the ends of quarter wavelength lines to ground, presenting a high impedance towards the receiver. In this way no power is delivered into the receiver, the transmit path remains undisturbed, and the receiver is protected during transmission. In the receive mode, all these diodes are off. The off capacitance of CR6502 is tuned by L6508 to form a high
30 Watt PA
The 30-Watt PA is a four stage radio frequency (RF) power amplifier used to amplify the output from the TX injection lineup to the radio transmit level. It consists of driver stage Q6501, two-stage power module U6501 and RF final device transistor Q6505. Q6505 and U6501 operate from the A+ supply voltage. U6501 is switched on/off by the K9.1 line through switch U6502 (which connects the A+ line to pin 2 of U6501 when transmit is enabled). The RF drive, which is routed into transistor Q6501, is controlled from Q6506 via the PA control line. The rising control voltage on the PA control line causes a rising collector voltage on Q6501. This causes more power out of the stage. Conversely, a decreasing control line voltage decreases the
September, 2000
6880906Z19-O
8-3
Theory of Operation Synthesizer Detailed Functional Description power delivered into the next stage. By controlling the drive power to U6501 and the following stages in the power amplifier lineup, ALC loop is able to regulate the output power of the transmitter. The antenna switch is switched synchronously with the keyed 9.1 voltage. In the transmit mode, this 9.1 voltage is highturning on diodes CR6502, CR6503 and CR1. When CR6502 is turned on, it forms a low impedance to the RF transmit path and allows the signal to pass to the antenna via harmonic filter hybrid H6502. Diode CR1 in H6502 forms a low impedance that is transformed up to an open circuit through a quarter wavelength transmission line. This prevents transmitter power from being delivered into the receiver. Diode CR6503 is also turned on in transmit mode further isolating the receiver from transmitter energy. The transmitter power from the antenna switch passes to the antenna via harmonic filter hybrid module H6502. H6502 incorporates a low pass filter, which attenuates harmonic energy out of the transmitter to specifications level. In receive mode, diodes CR6502, CR6403 and CR1 are all off. The off capacitance of CR6502 is tuned by L6512 to form a high impedance network looking into the transmitter. Therefore, received signal energy from the antenna is channeled to the input of the receiver with minimal loss maximizing sensitivity. A forward power detector utilizing a directional coupler is included in the harmonic filter hybrid. This forwardpower detector is a microstrip printed circuit, which couples a small amount of the forward energy to diode CR2 where it is rectified. This rectified signal (VFORWARD) forms the forward voltage which the power control circuit holds constant. Holding this voltage constant (which is proportional to the RF rectified energy appearing across the diode) ensures the forward-power out of the radio is held to a constant value. Thermistor R6519 senses temperature in a location near Q6505. This signal is fed back into the power control circuit to protect Q6505 against over-temperature conditions. Resistor R6520, in series with the A+ line supply, feeds voltage to Q6505. The voltage across R6520 is monitored and the difference voltage is channeled to the power control circuit. The power control circuit monitors the voltage drop across the resistor, which is determined by the magnitude of the collector current in Q6505. It uses this as a limiting mechanism whereby the power control circuit limits the magnitude of current that can be drawn by Q6505. This protects the device from over dissipation. Bias voltage reverse polarity protection for the transmitter is provided by diode CR6508. Under reverse polarity conditions to the radio, this diode conducts and protects the radio from damage. This diode also provides transient over-voltage protection by breaking down when the supply voltage to the radio exceeds 24 VDC.
Power Control Circuitry

The power control circuitry consists of three mechanisms: Power Set The control loop compares the power output level to the pre-set value. The VFORWARD voltage from the forward power detector is amplied by U701 pins 5 -7, and compared to D/A U702-2 & 4. Should a difference be detected, an error current is generated in the loop integrator U702-8 & 9, until equilibrium is obtained. The use of 2 D/A outputs for power set enables fine tuning where pin 2 is coarse tune through resistor R703 and pin 4 is ne tune through resistor R706. Current Limit Current to the power module U6501 (or RF nal device Q6505) is monitored using R6520 and compared to a pre-set limit D/A U702-11 and U701-(1-3). When the limit is exceeded, an error current is generated through diode CR721 to the loop integrator, which lessens the PA_CNTRL line and reduces the power amplier output. Thermal Protection When the power module U6501 (or RF final device Q6505) overheats, the resistance of thermistor R6519 drops. Because of the voltage divider formed by R721, R725, and R6519, this resistance drop is sensed and amplied through U701-(12-14). This causes a current error through diode CR721 to flow into the loop integrator and reduce transmitted output power. When controller U101-45, detects a voltage proportional to 85 degrees Centigrade through R726-727 it reduces transmit power by 50 percent during subsequent Tx key-ups.
Synthesizer Detailed Functional Description

The complete synthesizer subsystem consists of reference oscillator U5700, Fractional-N Synthesizer IC U5702, two on-board voltage controlled oscillators, buffer stage U5701, and two discrete buffer ampliers Q5707, and Q5705. Reference oscillator U5700 contains a temperature compensated crystal which operates at a frequency of 16.8 MHz. The output of the oscillator U5700-10 is applied to U5702-14 via R5715 and C5733. There are two varactor tuned VCOs. The oscillator frequency is controlled by the voltage applied via L5701 and L5702. This control voltage ranges from 2.5 to 10.5 VDC. A lower control voltage produces a lower fre-
8-4
6880906Z19-O
September, 2000
Theory of Operation Synthesizer Detailed Functional Description
quency and a higher control voltage produces a higher frequency respectively. The RX/TX VCO (896 - 902MHz band) provides the rst LO injection frequency which is 39 MHz below the RX carrier frequency and TX injection for conventional mode. The RX/TX VCO is selected by pulling U5702-1 low. The Talk-Around (TA) VCO (935 - 941MHz band) provides the transmit frequency in TA mode. The TA VCO is selected by pulling U5702-1 high. The buffer stage U5701 and feedback amplier Q5703 provide the necessary gain and isolation for the synthesizer loop. Fractional-N Synthesizer IC U5702 consists of: Prescaler, Programmable loop divider, Control divider logic, Phase detector, Charge pump, A/D Converter for low frequency digital modulation, Balance attenuator to balance the high and low frequency analog modulation, 13-V positive voltage multiplier, Serial interface for control, Super lter for the regulated 9.3 V DC C5712 is the super lter capacitor. The output voltage of the super filter U5702-18, drops from 9.3 VDC to about 8.5 VDC. This ltered 8.5 VDC supplies voltage for the VCOs, the VCO switching units U5704 & U5705, feedback amplifier Q5703, and synthesizer charge pump resistor network R5707- R5709. The synthesizer supply voltage is provided by the 5 VDC regulator U5703. The 2.1 MHz reference signal at U5702-11 is generated by dividing down the signal of reference oscillator U5700 after it is applied to U570214. In order to generate a high voltage that supplies the charge pump output stage at VCP (U5702-32), 13 V DC is generated at pin 3 of CR5700 by the positive voltage multiplier circuitry. This voltage multiplier is a diode capacitor network driven by two 1.05 MHz, 180-degree out-of-phase signals from U5702-9 &10. The serial interface (SPI_DATA) is connected to the microprocessor via the data line (U5702-5), clock line (U5702-6), and chip enable line (U5702-5). Proper
enabling of these lines allows the microprocessor to program the synthesizer. The output of the VCO is fed to the buffer input port of U5701-1. The output of the buffer U5701-5 is applied to the input of the feedback amplifier Q5703 through an attenuator network consisting of R5735, R5733 and R5732. To close the synthesizer loop, the output of Q5703 is connected to PREIN (U5702-20) of the synthesizer. The buffer output U5701-5 also provides the signal for receiver LO injection and transmit injection lineup. The charge pump current is present at U5702-31. The loop lter (which consists of R5716, R5717, R5734, C5750, C5744, C5745, C5736, C5746, C5747, C5794, C5795, C5796, C5797, C5798, C5799) will then transform this current into a voltage that will, in turn, be applied to Vcontrol of the VCOs and steer the output frequency. In order to modulate the PLL a two-point modulation method is utilized. The audio signal is applied to both the A/D converter (low frequency path) as well as the balance attenuator (high frequency path) via U5702-8. The A/D converter will convert the low-frequency, analog modulating signal into a digital code that will in turn be applied to the loop divider. This will cause the carrier to deviate. The balance attenuator is used to adjust the VCO deviation sensitivity to high frequency modulating signals. The output of the balance attenuator is present at the MODOUT port U5702-28. The transmit injection line-up consists of two amplier stages, Q5707 & Q5705, used to provide a constant output to drive the RF transmitter and provide isolation. The Q5705 stage is actively biased through Q5701, and Q5707 has passive biasing. The TX injection line-up is on only during the transmit mode (K 9.1V line is at 9.1 V). The rst VCO is used for receive LO_INJ and TX_INJ in the conventional 896-902 MHz transmit band. The second VCO is used for TX_ INJ in the talk-around 935941 MHz transmit band. The VCOs get their control voltage through L5701 and L5702. Q5704 and Q5706 are the oscillation transistors. C5793, C5792 and C5785, C5784 are the oscillator feedback capacitors. U5706 and U5707 are micro strip resonators. CR5701 and CR5702 are the varactors. C5790 and C5782 determine the VCO KV. C5703 and C5704 determine the VCO operation frequency. C5791 and C5783 are the coupling capacitors between the tank and the oscillation transistor. The two VCOs are coupled to buffer amplifier Q5702 through C5789 and C5786. The buffer amplier output signal is fed to U5701-pin 1 through C5770 & R5736.
September, 2000
6880906Z19-O
8-5
Theory of Operation Controller Detailed Functional Description
Controller Detailed Functional Description

General
The radio controller consists of four main subsections: Digital Control Audio Processing Power Control Voltage Regulation The digital section consists of a microprocessor, memory ICs, glue logic circuitry, signal MUX ICs, On/Off circuit, and general purpose Input/Output circuitry. The controller is based on the Motorola 68HC11K1 microprocessor-U101, 8-Kbyte SRAM-U103, 32 KbyteFlash memory-U102, and 8 Kbyte EEPROM -U104. NOTE From this point on, the 68HC11K1 microprocessor will be referred to as K1P or P. References to a Control Head will be to type P+ (Display radio).
UNSW_+5V_CL is only used by a few circuits, which draw low current and require 5 VDC while the radio is off. UNSW_+5V_CL is used to save the internal U103 RAM data. C622 allows the battery voltage to be disconnected for a couple of minutes without losing RAM parameters. Diode D621 prevents radio circuitry from discharging this capacitor. The SW_+B voltage is monitored by the P through voltage divider R641-642. Diode VR641 limits the divided voltage to 5.1 VDC in order to protect the P. Diode CR6508 located in the PA section acts as protection against transients and reverse polarity of the supply voltage.
Electronic On/Off
The radio has circuitry which allows radio software and/or external triggers to turn the radio on or off without direct user action. This allows, for example, automatic turn-on when ignition is sensed and off when ignition is off. Q611 is used to provide SW_B+ to the various radio circuits. Q611 acts as an electronic on/off switch controlled by Q612 (the switch is on while Q612 is on). When the radio is turned on, the voltage at the base of Q612 is high (about 0.6 V). Q612 switches on (saturation) and pulls down the voltage at Q611-base. This turns on Q611 and supplies SW_B+ to the radio. The on resistance of Q611 is very low (less than 1 OHM), so the voltage level at SWB+ is essentially the same as A+. The electronic on/off circuitry can be enabled by the microprocessor (through ASFIC, B+ _CONTROL), the mechanical On/Off button on the control head (ON_OFF_CONTROL), or the ignition sense circuitry (IGNITION_CONTROL). If one of the three paths causes a low at the collector of Q612, the electronic ON process is engaged.
Voltage Regulators
Voltage regulation for the controller is provided by 3 separate devices: +5 VDC U631, +9.3 VDC U601, and UNSW 5V (R621 and VR621). An additional regulator is located in the RF section. 5 VDC regulation for the digital circuitry is provided by U631. Input and output capacitors C631, C632 and C633-635 are used to reduce high-frequency noise and provide additional charge during short battery transients. This regulator provides a reset output U631-5 that drops to 0 VDC when the regulator output goes out of regulation. This is used to reset the controller in order to prevent improper operation. Diode D631 prevents discharge of C632 by negative spikes on the 9.3 voltage. Regulator U601 is used to generate the 9.3 VDC required by some audio circuits, the RF circuitry and power control circuitry. Input and output capacitors C601-603 and C604-605 are used to reduce high-frequency noise. R602-603 set the regulator output voltage. If the voltage at U601-1 is greater than 1.3 VDC the regulator output decreases and if the voltage is less than 1.3 VDC, the regulator output increases. This regulator output is electronically disabled by a 0 VDC signal on U601-2. Q601 and associated circuitry R601, R604-605 disable the regulator when the radio is turned off.
Mechanical On/Off
This refers to the typical on/off button which is located on the control head and turns the radio on and off. While the on/off button is turned on, line ON_OFF_ CONTROL goes high during the short pulse generated by the ON_OFF one-shot circuitry in the control head. This switches the radio on. The microprocessor is alerted through line ANALOG_ 3 which is pulled to low by Q925 (in Control Head Model P+) while the on/ off button is turned on. If the software detects a low state, it asserts B+_CONTROL via ASFIC-GCB2, which keeps Q612 and Q611 on, and in turn the radio is switched on. When the on/off button is turned off, the software detects the line ANALOG_3 changing to low and switches the radio off by setting B+_CONTROL to low.
8-6
6880906Z19-O
September, 2000
Theory of Operation Controller Detailed Functional Description
Ignition
Ignition sense is used to prevent the radio from draining the vehicles battery while the engine is not running. When the IGNITION input goes above 1.3VDC, Q450, Q612 and Q611 turn on, supplying SW_B+ to the radio and enabling U601 and U631 to supply the regulated voltage (+5 VDC and 9.3 VDC) to all the circuitry. The P s t a r t s t o ru n t h e s o f t w a re , re a d s t h e l i n e IGNITION_SENSE, determines from the level that the IGNITION input is active and sets the B+_CONTROL (via the ASFIC-GCB2) to high and latches SW_B+ on. When the IGNITION line drops below 1.3 VDC, Q450 switches off and R441 pulls line IGNITION_SENSE high. The software is alerted by line IGNITION_SENSE to switch off the radio by setting B+ CONTROL line to low. Whenever the IGNITION line goes above 1.3 VDC, the above process will be repeateddepending if the radio was previously on or off. The ignition sense capability can be disabled by turning switch S401-2 & 4 on. This supplies FLT_A+ via R452 to the ignition sense pin continuously. The radio is shipped with ignition sense disabled.
this clock source interfere with the specific radio receive frequency. The ASFIC synthesizer loop components (C228, C229 and R222) set the switching time and jitter of the clock output. If the synthesizer cannot generate the required clock frequency it will switch back to its default 3.6864 MHz frequency.
Serial Peripheral Interface (SPI)

The P communicates with the other programmable ICs through its SPI port. This port consists of SPI TRANSMIT DATA U101-1, SPI RECEIVE DATA U10180, SPI CLK U101-2 and chip select lines going to the various programmable ICs. This BUS is a synchronous bus (the timing clock signal CLK is sent with SPI TRANSMIT DATA or SPI RECEIVE DATA). In the controller section, there are three ICs on the SPI BUS: ASFIC (U201-E3), EEPROM (U104-1) and D/A (U731-6). In the RF sections, there are 2 ICs on the SPI BUS: Pendulum (Reference Oscillator U5702-24) and Synthesizer (U5701-7). The SPI TRANSMIT DATA and CLK lines going to the RF section are ltered with L131 and L132 to minimize noise. The chip select lines for the ICs are decoded by the address decoder U105. The SPI BUS is also used for the control head. U106 buffers the SPI TRANSMIT DATA and CLK lines to the control head. U106 serves also to switch off the CLK signal for the LCD display while it is not selected via LCD_CE signal. When the P needs to program any of these ICs, it drops down the chip select line of the specific IC to a logic 0 and then sends the proper data and clock signals. The data sent to the various ICs are different. For example the ASFIC receives 21 bytes (168 bits) while the DAC needs 3 bytes (24 bits). After the data has been sent the chip select line is returned to a logic 1.
Hook
The HOOK line is used to inform the P when the Microphones hang-up switch is engaged. Depending on the radios programing , the P turns the audio PA on or off. The signal is routed from J101-3 and J400-14 through transistor Q101 to the K1P U101-23. The voltage range of HOOK in normal operating mode is 0-5 VDC.
Microprocessor Clock Synthesizer

The clock source for the controllers microprocessor system is generated by the ASFIC (U201). Upon powerup the synthesizer (U5701) generates a 2.1 MHz waveform that is routed from the RF section (via C202) to the ASFIC (on U201 XTAL_IN). For the main board controller, the ASFIC uses 2.1 MHz as a reference input clock signal for its internal synthesizer. The ASFIC, in addition to audio circuitry, has a programmable synthesizer which can generate a synthesized signal ranging from 1200 Hz to 32.769 MHz with steps of 1200 Hz. While the radio is turned on, the ASFIC generates a default 3.6864 MHz CMOS square wave P CLK (on U201-UPCLK) which is routed to the P (U101EXTAL). After the P starts operation, it reprograms the ASFIC synthesizer clock to a higher P CLK frequency (usually 7.3728 or 14.7456 MHz) and continues operation. The ASFIC synthesizer clock is controlled by the software, and may slightly be changed while harmonics of
SBEP Serial Interface

The SBEP serial interface line allows the radio to communicate with the Radio Service Software (RSS). This interface connects to the Microphone connector (J902) via Control Head connector (J101) and comprises BUS+ (J101-15). The line is bi-directional, meaning that either the radio or the DPS can drive the line. The connection from the Control Head is made through the BUS+ line, via L421 (SCI_RSS line) and diode CR151 to the U101-78-RxD and U101-79-TxD ports.
Microprocessor (Open Controller)

For this radio, the K1P is congured to operate in the expanded or bootstrap modes. In expanded mode the K1P uses external memory ICs, whereas in bootstrap mode it uses only its internal memory. In normal radio
September, 2000
6880906Z19-O
8-7
Theory of Operation Controller Detailed Functional Description operation, the K1 P is operating in the expanded mode. In the radio expanded mode, the K1 P (U101) has access to three external memory ICs: U102 (Flash memory), U103 (SRAM), U104 (EEPROM). Also, within the K1P there are 768 bytes of internal RAM and 640 bytes of internal EEPROM, as well as glue logic circuitry to select external memory ICs. The external EEPROM (U104) as well as the K1Ps own internal EEPROM contain the radio information which is customer specic, referred to as the codeplug. This information consists of items such as: 1) frequency operating band, 2) channel frequencies, and 3) general tuning information. General tuning information and other more frequently accessed items are stored in the internal EEPROM (within the 68HC11K1), while the remaining data is stored in the external EEPROM. (See the particular IC subsection for more details.) The external SRAM (U103) as well as the K1Ps own internal RAM are used for temporary calculations required by the software during normal radio operation. All of the data stored in both of these locations is lost when the radio is powered off. (See the particular IC subsection for more details.) The Flash memory contains the actual Radio Operating Software. This software is common to all radios for the same model type. For example, Privacy Plus models have a different version of software in Flash memory than an LTR model. (See the particular IC subsection for more details.) The K1P has an address bus of 16 address lines (A0A15), a data bus of 8 data lines (D0-D7). and three control lines; CSPROG (U101-29) to select U102-30 (OTP memory), CSGP2 (U101-28) to select U103-20 (SRAM) and PG7_R_W for read and write. All other chips (ASFIC/PENDULLUM/DAC/FRACN/LCD/LED/ EEPROM) are selected by 3 lines of the K1P using chip select decoder U105. When the K1P is functioning normally, the address and data lines should be within CMOS logic levels. The low-order address lines (A0-A7) and the data lines (D0-D7) should change. On the K1P the lines XIRQ (U101-30), MODA LIR (U101-77), MODB VSTPY (U101-76) and RESET (U10175) should be logic high during all normal K1P operation. Whenever a data or an address line becomes unloaded or shorted to an adjacent line, a common symptom is that short negative pulses occur on the RESET line, with a period of 20 msec. When two lines are short-circuited, mid logic level (around 2.5 V) may be observed, while these lines are opposite driven by two different ICs. The MODA LIR (U101-77) and MODB VSTPY (U101-76) inputs to the K1P must be at a logic 1 level
for proper operation. After the K1P starts execution, it will periodically pulse these lines to determine the desired operating mode. While the Central Processing Unit (CPU) is running a new instruction, MODA LIR (as an open-drain CMOS output) drops low. However, since it is an open-drain output, the signal waveform rise has an exponential shape, like an RC circuit. The P has eight analog-to-digital converter ports (A/ D): PE0 to PE7. These lines may measure voltage levels in the range of 0 to 5 VDC and convert that level to a number ranging from 0 to 255 which can be read by the software to take appropriate action. For example, U101-46 is the battery voltage detect line. R641 and R642 form a resistor divider on SW_B+. With 47.5K and 16.2 K and a voltage range of 11 V to 17 V, the A/D port would see 2.74 V to 4.24 V which would then be converted to a digital value in the range of 140 to 217 respectively. U101-51 is the high reference voltage for the A/D ports on the K1P. Resistor R106 and capacitor C106 lter the +5 VDC reference. If this voltage is lower than +5 VDC the A/D readings will be incorrect. Likewise U101-50 is the low reference for the A/D ports. This line is normally tied to ground. If this line is not connected to ground, the A/D readings will be incorrect. Capacitors C104, C105 serve to lter out any AC noise which may ride on +5VDC at U101.
One-Time Programmable (Flash) Memory

The 32-KByte Flash memory (U102) contains the radios operating software. This memory is read-only. The memory access signals (EN_CE, EN_OE and EN_WE) are generated by the P. Capacitor C131 serves to lter out any AC noise which may ride on +5V at U101, and C132 lters out any AC noise on Vpp.
Electrically Erasable Programmable Memory (EEPROM)

EEPROM (U104) contains the radios operating parameters such as operating frequency and signalling features, commonly known as the codeplug. It is also used to store radio operating state parameters such as current mode and volume. U104 is a 8 Kbyte device. This memory can be written to in excess of 100,000 times and will retain the data when power is removed from the radio. The memory access signals (SI, SO and SCK) are generated by the K1P and chip select (CS_) is generated by address decoder U105. Additional EEPROM is contained in the K1P (U101). This EEPROM is used to store radio tuning and alignment data. Like the external EEPROM this memory can
8-8
6880906Z19-O
September, 2000
Theory of Operation Controller Audio & Signaling Circuits
be programmed multiple times and will retain the data when power is removed from the radio. NOTE The external EEPROM plus the 640 bytes of internal EEPROM in the 68HC11K1 comprise the complete codeplug.
DATA BUF is shifted into the display driver by clock signal LCD CLCK BUF.
Controller Audio & Signaling Circuits

General
Audio Signalling Filter IC (ASFIC) The ASFIC (U201) used in the controller has four functions; RX/TX audio shaping, i.e. ltering, amplication, attenuation RX/TX signalling, PL/DPL/HST/LST Squelch detection Microprocessor clock signal generation (see Microprocessor Clock Synthesizer Description Block). The ASFIC is programmable through the SPI BUS (U201-E3/F1/F2), normally receiving 21 bytes. This programming sets up various paths within the ASFIC to route audio and/or signalling signals through the appropriate filtering, gain and attenuator blocks. The ASFIC also has 6 General Control Bits GCB0-5 which are CMOS level outputs. They are used for AUDIO _PA _ENABLE (GCB0) to switch the audio PA on and off, EXTERNAL_ALARM (GCB1) to toggle the EXTERNAL_ALARM pin on the accessory connector J400-4, B+_CONTROL (GCB2) to switch the voltage regulators (and the radio) on, HIGH_LOW_BAND (GCB4) to enable/disbale HearClear and FAST_OFF_IGN (GCB5) which forces the radio-on latch to the off condition. GCB3 is not used. Audio Ground VAG is the dc bias used as an audio ground for the opamps that are external to the Audio Signalling Filter IC (ASFIC). U251 forms this bias by dividing 9V3Vwith resistors R251, R252, and buffering the 4.65 VDC result with a voltage follower. VAG emerges at pin 1 of U251. C235 is a bypass capacitor for VAG. The ASFIC generates its own 2.5V bias for its internal circuitry. C221 is the bypass for the ASFICs audio ground dc bias. NOTE While there are ASFIC VAG, and BOARD VAG (U201-1), each of these are separated. They are not connected together.
Static Random Access Memory (SRAM)

The SRAM (U103) contains temporary radio calculations or parameters that can change very frequently, and which are generated and stored by the software during its normal operation. The information is lost when the radio is turned off. The device allows an unlimited number of write cycles. SRAM accesses are indicated by the EN_CS signal U103-20 (which comes from U101-28) going low. U103 is commonly referred to as the external RAM as opposed to the internal RAM which is the 768 bytes of RAM which is part of the 68HC11K1. Both RAM spaces serve the purpose. However, the internal RAM is used for the calculated values which are accessed most often. Capacitor C133 serves to lter out any AC noise which may ride on +5VDC at U103.
Control Head
Control Head is available for user interface. The Control Head contains the internal speaker, the microphone connector, several buttons to operate the radio and several indicator LEDs to inform the user about the radio status. Additionally Control Head uses a 3 digit LCD (Liquid Crystal Display) for the channel number. When turned on, the On/Off switch turns the voltage regulators on by pulling ON_OFF_CONTROL to high and connects the base of Q925(P), Q825(K) to FLT_A+. This transistor pulls the line ANALOG_3 to low to inform the P that the On/Off button is pressed. If the radio is switched off, the P will switch it on and vice versa. All other buttons work the same way. If a button is pressed, it will connect one of the 3 lines ANALOG_ 1,2,3 to a resistive voltage divider connected to +5VDC. The voltages of the lines are A/D converted inside the P and specify the pressed button. All the back light and indicator LEDs are driven by current sources and controlled by the P via SERIAL PERIPHERAL INTERFACE (SPI) interface. The LED status is stored in shift register U941(P). Line LED CE enables the serial write process via Q941(P), while line LED CLCK BUF shifts the data of line SPI DATA BUF into the shift register. In addition Control Head contains the LCD H931, the display driver U932 and a transistor Q953 to switch the display driver on and off. Q953 is controlled by the P via shift register U941, The display data of line SPI
September, 2000
6880906Z19-O
8-9
Transmit Audio Circuits.

Mic Input Path The radio provides two microphone inputs, one on the control head (internal mic audio) routed through J10116), and one on the accessory connector J400-2 (external mic audio). The two inputs are connected in parallel. The dc bias required by the microphone is provided by resistor R205, derived from the 9V3 source and ltered by R204 and C209. The microphone audio signal is applied via R206 and C211, to the ASFIC at U201-B8. Filter capacitor C210 provides low-pass filtering to eliminate frequency components above 3 kHz, and C211 serves as a DC blocking capacitor. The audio signal at U201-B8 should be approximately 80mV for 60% of full system deviation. Flat Tx Audio Input Path The FLAT_TX_AUDIO signal from accessory connector J400-5 is buffered by op-amp U202-(1-3) and fed via C205 to the ASFIC U201-D7. PTT Sensing and TX Audio Processing MIC PTT is sensed by the P. PTT can also be generated by grounding pin 3 on the radio accessory connector, J400. When microphone PTT is sensed, the P will always configure the ASFIC to enable the mic audio
path. PTT can be configured to enable the EXT_MIC audio path when J400-2 is connected with an external mic audio input. Data PTT is congured to enable the at transmit audio path (when J400-5 is congured for FLAT_TX_AUDIO). Inside the ASFIC, the mic audio is ltered to eliminate components outside the 300-3000Hz voice band and pre-emphasize. The capacitor, C231, between ASFIC pre-emphasis out U201-C8 and ASFIC limiter in U201E8 AC couples the signal between ASFIC blocks and prevents the DC bias at the ASFIC output U0201-H8 from shifting when the ASFIC transmit circuits are enabled. The signal is then limited to prevent the transmitter from over deviating. The limited mic audio is then routed through a summer which is used to add in signalling data, and then to a splatter lter to eliminate high frequency spectral components that could be generated by the limiter. The audio is then routed to the VCO attenuator, which is tuned in the factory or the eld to set the proper amount of FM deviation. The TX audio emerges from the ASFIC at U201-H8 MOD IN, and is routed to the RF section as MOD IN.
Transmit Signalling Circuits

See Figure 8-4 for reference for the following sections. From a hardware point of view, there are three types of signalling:
D3 COMP BUF IN HEARCLEAR IC U350 COMP OUT F3 A6 C7 TX IN ASFIC U201 MIC IN B8 FILTERS & PREEMPHASIS
CONTROL HEAD CONNECTOR
HPF
J101 16
MIC AMP OUT
MIC
ACCESSORY CONNECTOR
EXT MIC J400 FLAT TX AUDIO
2 5 D7 AUX TX IN
LS SUMMER SPLATTER FILTER HS SUMMER LIMITER ATTENUATOR VCO ATN H8 MOD IN
TO RF SECTION (SYNTHESIZER)
PRE EMP OUT C8
LIM IN E8
Figure 8-3.
Transmit Audio Paths
8-10
6880906Z19-O
September, 2000
Sub-audible data (PL/DPL/LST/Connect tone) that gets summed with transmit voice or signalling, DTMF data for telephone communication in trunked and conventional systems, and Audible signalling High speed Trunking. NOTE The hardware supports all three types while the radio software determines which signalling type is available. Sub-audible Data (PL/DPL) Sub-audible data implies signalling whose bandwidth is below 300Hz. PL and DPL waveforms are used for conventional operation and connect tones for trunked voice channel operation. The trunking connect tone is simply a PL tone at a higher deviation level than PL in a conventional system. Although it is referred to as sub-audible data, the actual frequency spectrum of these waveforms may be as high as 250 Hz, which is audible to the human ear. However, the radio receiver filters out any audio below 300Hz, so these tones are never heard in the actual system. Only one type of sub-audible data can be generated by U201 (ASFIC) at any one time. The process is as follows, using the SPI BUS, the P programs the ASFIC to set up the proper low-speed data deviation and select the PL or DPL filters. The P then generates a square wave which strobes the ASFIC PL/DPL encode input PL CLK U201-C3 at twelve times the desired data rate. For example, for a PL frequency of 103 Hz, the frequency of the square wave would be 1236 Hz. This drives a tone generator inside U201 which generates a staircase approximation to a PL sine wave or
ASFIC U201
DPL data pattern. This internal waveform is then lowpass filtered and summed with voice or data. The resulting summed waveform then appears on U201H8 (MOD IN), where it is sent to the RF board as previously described for transmit audio. A trunking connect tone would be generated in the same manner as a PL tone. High Speed Data High speed data refers to the 3600 baud data waveforms, known as Inbound Signalling Words (ISWs) used in a trunking system for high speed communication between the central controller and the radio. To generate an ISW, the P first programs the ASFIC (U201) to the proper filter and gain settings. It then begins strobing U201-G1 (TRK CLK IN) with a pulse when the data is supposed to change states. U201s 53-2 State Encoder (which is in a 2-state mode) is then fed to the post-limiter summer block and then the splatter lter. From that point it is routed through the modulation attenuator and then out of the ASFIC to the RF board. Microphone audio is muted during High Speed Data signalling. Dual Tone Multiple Frequency (DTMF) Data DTMF data is a dual tone waveform used during phone interconnect operation. It is the same type of tones which are heard when using a Touch Tone telephone. There are seven frequencies, with four in the low group (697, 770, 852, 941Hz) and three in the high group (1209, 1336, 1477Hz). The high-group tone is generated by the P (U101-5) strobing U201-G1 at six times the tone frequency for
HS SUMMER
G1 HIGH SPEED CLOCK IN
5-3-2 STATE ENCODER DTMF ENCODER
SPLATTER FILTER
7 MICRO CONTROLLER U101 6
G2
DTMF CLOCK
C3
LOW SPEED CLOCK
PL/DPL/LST ENCODER
LS SUMMER H8 ATTENUATOR MOD IN TO RF SECTION (SYNTHESIZER)
Figure 8-4.
Transmit Signalling Paths
September, 2000
6880906Z19-O
8-11
Theory of Operation Controller Audio & Signaling Circuits tones less than 1440Hz or twice the frequency for tones greater than 1440Hz. The low group tone is generated by the P (U101-7) strobing U201-G2 (DTMF CLCK) at six times the tone frequency. Inside U201 the lowgroup and high-group tones are summed (with the amplitude of the high group tone being approximately 2 dB greater than that of the low group tone) and then pre-emphasized before being routed to the summer and splatter filter. The DTMF waveform then follows the same path as was described for high-speed data.
DET_AUDIO is routed to the ASFICs squelch detect circuitry input SQIN (U201-H7). All of the squelch detect circuitry is contained within the ASFIC. Therefore from a users point of view, DET_AUDIO enters the ASFIC, and the ASFIC produces two CMOS logic outputs based on the result. They are CHACT (U201-H2) and SQDET (U201-H1). The squelch signal entering the ASFIC is amplied, ltered, attenuated, and rectied. It is then sent to a comparator to produce an active high signal on CHACT. A squelch tail circuit is used to produce SQDET (U201-H1) from CHACT. The state of CHACT and SQ DET is high (logic 1) when carrier is detected, otherwise low (logic 0). CHACT is routed to U101-25 while SQDET adds up with LOCK_DET, weighted by resistors R113 and R114,
ACCESSORY CONNECTOR J400 11 13 EXT RX AUDIO INT SPKR+ JUMPER
Receive Audio Circuits

Squelch Detect
The radios RF circuits are constantly producing an output at the discriminator (U5201-28). This signal
1 U401 AUDIO PA 9 4 6 SPKR+ SPKR16 1
EXTERNAL SPEAKER
INT SPKR+
INT SPKRCONTROL HEAD CONNECTOR
ATTEN.
J101
2 1 14 HANDSET AUDIO INTERNAL SPEAKER
C1 EXP IN U350 HEARCLEAR H5 UNAT RX OUT A2 EXP OUT F4 FF OUT FFIN E4 J5 EXP AUDIO IN H6 RX IN
FILTER & DEEMPHASIS PL LIM VOLUME ATTEN.
J4
RX AUD OUT
ASFIC U201
J7 PL IN
LIMITER, RECTIFIER FILTER, COMPARATOR
PL FILTER LIMITER SQUELCH CIRCUIT SQ DET
A4
FROM RF SECTION (IFIC)
SQ IN
CH ACT
H7
DET AUDIO (DISCRIMINATOR AUDIO)
H2 25 68 MICRO CONTROLLER U101
H1
10
Figure 8-5. 8-12
Receive Audio Paths

September, 2000
6880906Z19-O
and is routed to an A/D converter input U101-43. From the voltage weighted by the resistors the P determines whether SQDET, LOCK_DET or both are active. SQDET is used to determine all audio mute/unmute decisions except for Conventional Scan. In this case CHACT is a pre-indicator as it occurs slightly faster than SQDET. Audio Processing and Digital Volume Control The receiver audio signal enters the controller section from the IF IC (U5201-28) on DET_AUDIO and passes through RC filter R203 and C208 which filters out IF noise. The signal is AC coupled by C207 and enters the ASFIC via PLIN U201-J7. Inside the ASFIC, the signal goes through two paths in parallel, the audio path and the PL/DPL path. The audio path has a programmable amplier, whose setting is based on the channel bandwidth being received, then a LPF filter to remove any frequency components above 3000Hz and then an HPF to strip off any sub-audible data below 300Hz. Next, the recovered audio passes through a De-emphasis lter to compensate for Pre-emphasis which is used to reduce the effects of FM noise. The IC then passes the audio through the 8-bit programmable attenuator whose level is set depending on the value of the volume control. Finally the ltered audio signal passes through an output buffer within the ASFIC. The audio signal exits the ASFIC at RX_AUDIO (U201-J4). The P programs the attenuator, using the SPI bus, based on the volume setting. The minimum /maximum settings of the attenuator are set by codeplug parameters. Since sub-audible signalling is summed with voice information on transmit, it must be separated from the voice information before processing. Any sub-audible signalling enters the ASFIC from the IF IC at PLIN U201-J7. Once inside it goes through the PL/DPL path. The signal rst passes through one of 2 low pass lters, either PL low pass filter or DPL/LST low pass filter. Either signal is then ltered and goes through a limiter and exits the ASFIC at PLLIM (U201-A4). At this point the signal will appear as a square wave version of the sub-audible signal which the radio received. The microprocessor, U101-10 will decode the signal directly to determine if it is the tone/code which is currently active on that mode. Audio Amplication Speaker (+) Speaker (-) The ASFICs received audio signal output, U201-J4, is routed through a voltage divider formed by R401 and R402 to set the correct input level to the audio PA (U401). This is necessary because the gain of the audio PA is 46 dB, and the ASFIC output is capable of overdriving the PA unless the maximum volume is limited.
The audio then passes through C401 which provides AC coupling and low frequency roll-off. C402 provides high frequency roll-off as the audio signal is routed to pins 1 and 9 of the audio power amplier U401. The outputs of the Audio PA (U401 pins 4 and 6) are routed to the external speaker via the accessory connector (J400-16 EXT SPKR+, and J400-1 EXT SPKR-, respectively). One terminal of the radios internal speaker (+) is connected to J400-13 (INT SPKR+), and the other (-) to U401-6. To enable the internal speaker, a jumper plug is inserted into J400 which connects pins 13 and 16 together. This completes the path between the audio power amp U401-4 and the internal speakers (+) terminal. The audio power amplifier has one inverted and one non-inverted output that produces the differential audio output OUT1 and OUT2 (U401-4 & 6). The inputs for each of these amplifiers are pins 1 and 9 respectively; these inputs are both tied to the received audio. The audio PAs DC bias is not activated until the audio PA is enabled at pin 8. The audio PA is enabled via AUDIO_PA_ENABLE signal from the ASFIC (U201-B5). When the base of Q401 is low, the transistor is off and U401-8 is high, using pull up resistor R406, the audio PA is ON. The U401-8 must be above 8.5VDC to properly enable the device. If the voltage is between 3.3 and 6.4V, the device will be active but has its input (U401-1/9) off. This is a mute condition which is not employed in this radio design. R404 ensures that the base of Q401 is high on power up. Otherwise there may be an audio pop due to R406 pulling U401-8 high before the software can switch on Q401. The audio PA can also be muted externally when in the Data Modem mode, which is selected by turning switch S401 (1-3) off. This forces analog switch control line U402-9 high via R442, changing its state. If J400-12 is pulled low, this is transferred via pins 14 and 1 of U402 to the base of Q415, turning it on and, in turn, Q401 on. This pulls U401-B low, muting the audio PA. The EXT_SPKR+ and EXT_SPKR- outputs of the audio PA have a DC bias which varies proportionately with FLT A+ (U401-7). FLT A+ of 11V yields DC offset of 5V, and FLT A+ of 17V yields a DC offset of 8.5V. If either of these lines is shorted to ground, it is possible that the audio PA will be damaged. The audio PA contains internal short-circuit protection, however this situation should be avoided. EXT_SPKR+ and EXT_SPKR- are routed to the accessory connector (J400-16 & 1) and, via the jumper plug connecting J400-16 to 13, to the control head (connector J101-1 & 2). Handset Audio Certain hand-held accessories have a speaker within them which require a different voltage level than that provided by U401. For those devices HANDSET
September, 2000
6880906Z19-O
8-13
Theory of Operation Controller Audio & Signaling Circuits AUDIO is available at control head microphone jack J903-8. The received audio from the output of the ASFICs digital volume attenuator (U201-J4) is also routed to U202-9 where it is amplified 15 dB; this is set by the 10k/68k combination of R233 and R232. This signal is routed from the output of the op amp U202- 8 to J10114. The control head sends this signal directly out to the microphone jack. The maximum value of this output is 6.6Vp-p. External Rx Audio RX Audio is also routed to the accessory connector J400-11. This audio level is xed and not affected by the setting of the digital volume attenuator. The source of this audio is selectable as follows: In the Data Modem mode (switch S401, 1-3 off), U4029 is high, and FLAT_ RX_AUDIO, directly from detector U5201-28 via C230 and R236, is routed from U402 pin 10 to pin 5, amplied by U403 and applied to J40011 via R419 and C419. In Normal mode (switch S401 1-3 on), U402-9 is low, and GATED_RX_AUDIO, from ASFIC U201-H5 via C237 and R235, is routed from U402 pin 6 to pin 5, amplified by U403 and applied to J0400-11 via R419 and C419. The values of R235 and R236 provide the correct audio levels for GATED and FLAT_RX _AUDIO paths, respectively. The GATED_RX_AUDIO signal is PL-ltered, de-emphasized, and controlled by the squelch mute gate. The FLAT_ RX_AUDIO signal is non-de-emphasized, unmuted, and is flat between
0.6 Hz and 3 kHz. The radio is shipped congured for Normal mode operation.
Receive Signalling Circuits

Sub-audible Data (PL/DPL) and High Speed Data Decoder The ASFIC (U201) is used to lter and limit all received data. The data enters the ASFIC at U201-J7. Inside U201 the data is filtered according to data type (HS or LS), then it is limited to a 0-5V digital level. The trunking high speed data appears at U201-G4, where it connects to the P U101-11. The low speed limited data output (PL, DPL, and LST) appears at U201-A4, where it connects to the P U10110. While receiving low speed data, the P may output a sampling waveform depending on the sampling technique to U201-C3 between 1 and 2 kHz. The low speed data is read by the P at twice the frequency of the sampling waveform; a latch configuration in the ASFIC stores one bit every clock cycle. The external capacitors C223, C225, and C226 set the low frequency pole for a zero crossings detector in the limiters for PL and HS data. The hysteresis of these limiters is programmed based on the type of received data. NOTE During HS data, the P may generate a sampling waveform seen at U0201-G1.
G1 HIGH SPEED CLOCK DATA FILTER & DEEMPHASIS J7 PL IN DET AUDIO DISCRIMINATOR AUDIO FROM RF SECTION (IFIC)
C3 LOW SPEED CLOCK LIMITER G4 RX LIM OUT A4 PL LIM 10 11
ASFIC U201
FILTER LIMITER
MICRO CONTROLLER U101
LOW SPEED LIM CAP C5
RX LIM CAP J3
Figure 8-6.
Receive Signalling Path
8-14
6880906Z19-O
September, 2000
Alert Tone Circuits When the software determines that it needs to give the operator an audible feedback (for a good key press, or for a bad key press), or radio status (trunked system busy, phone call, circuit failures), it sends an alert tone to the speaker. It does so by sending SPI BUS data to U201 which sets up the audio path to the speaker for alert tones. The alert tone itself can be generated in one of two ways: internally by the ASFIC, or externally using the P and the ASFIC. The allowable internal alert tones are 304, 608, 911, and 1823Hz. In this case a code contained within the SPI BUS load to the ASFIC sets up the path and determines the tone frequency, and at what volume level to generate the tone. (It does not have to be related to the voice volume setting). For external alert tones, the P can generate any tone within the 100-3000Hz audio band. This is accomplished by the P generating a square wave which enters the ASFIC at U201-C3. Inside the ASFIC, this signal is routed to the alert tone generator; the output of the generator is summed into the audio chain just after the RX audio de-emphasis block. Inside U201 the tone is amplified and filtered, then passed through the 8-bit digital volume attenuator, which is typically loaded with a special value for alert tone audio. The tone exits at U201-J4 and is routed to the audio PA like receive audio. Hear Clear IC Hear Clear (HC) is used for 900 MHz radios. The HC has three functions within the IC which are used by the radio: 1) Compressor, 2) Flutter Fighter, and 3) Expander Circuits. There are six enable/control lines on the Hear Clear IC which determine its mode of operation. The IC ENAB line U350-C4 is tied to 9.3 so whenever the IC is placed on the board, it is always active. The remaining five lines are contolled by the ASIFIC General Control Bit Line. Table 8.1 below summarizies the logic control and the IC states. Transmit Path for Radios with Hear Clear For transmit, the audio signal comes from the appropriate microphone and enters the ASFIC at U200-B8. After entering the ASFIC, the signal is internally routed to U200-A6 ASFIC MIC AMP OUT, where it leaves the ASFIC and enters the Hear Clear compressor at U350-D3. The signal then exits the compressor at U350-F3, where it is routed back to the ASFIC U200-C7. C361 provides AC coupling. Inside the ASFIC, the signal goes through LPF and HPF that limits the signal between 0.3-3 kHz . The signal is then pre-emphasized and exits the ASFIC at U200-C8 and enters the ASFIC at U200-E8. Again inside the ASFIC, the signal goes
through a limiter, splatter filter, and an attenuator which sets the amplitude (deviation level) of the signal. The purpose of having a compressor in the transmit mode is twofold: 1) improve S/N ratio for low level audio, and 2) maintain the same dynamic range of 12.5 kHz bandwidth channel as obtained in the 25 KHz bandwidth. The compresssor raises low level signals and lowers high level signals. The compressor circuit produces a signal whose output voltage at pin U350-F3 is based on the input voltage level (0200-A6) of the signal. The voltage transfer function is: 20 mV input == 40 mV output 80 mV input == 80 mV output 50 mV input == 110 mV output Receive Path for Radios with Hear Clear The audio signal enters the Hear Clear controller from BBR signal on DISC. The discriminated audio DISC enters the Hear Clear Flutter Fighter through C300 and C367. C300 connects the signal to FF IN (U350-E4). C367 is a beginning of a noise sampling circuit consisting of components: C367, R356, R353, C364, C363, R354 and R355, R357, and C365; and Hear Clear ports Ref, Noise Filter In, and Noise Filter Out, Noise Hold. After exiting Hear Clear at the FF OUT (U350-F4), the signal enters ASFIC at RX IN (U200-H6). Within the ASFIC, the signal passes through a low lter and high pass lter limiting the audio band width to 0.3-3 kHz. It then goes through de-emphasis and exits the ASFIC at U200-H5 FILTERED AUDIO. After exiting the ASFIC at FILTERED AUDIO, the signal passes through capacitor C350, which provides AC coupling. The signal then enters the HEAR CLEAR at EXP IN (U350-C1) and exits the HEAR CLEAR Expander at EXP OUT (U350-A2). The normalized signal is then routed back to the ASFIC through C360 for volume adjustment, entering at U200-J5 and exiting the ASFIC at U200-J4 as RX AUDIO. The audio is trhen routed to the Audio PA in the same manner as standard receive audio. The purpose of Flutter Fighter is to sample the amount of Noise in the receive audio between 10 - 20 Khz using the Noise Filter in (U350-B5, Noise Filter Out (U350C6) and Noise Hold (U350-D5). In addition, it monitors the rate of change of RSSI (Receive Signal Strength In) (U350-F5). The discriminated audio DISC enters into the Hear Clear Ic at FF IN (U350-E4). The circuit then reduces the amount of popping Noise associated with fading. The improved audio exits the IC at FF OUT(U350-F4). The expander is used after de-emphasis but before the ASFIC volume attenuation. The purpose of the
September, 2000
6880906Z19-O
8-15
Theory of Operation Controller Audio & Signaling Circuits Table 8-1.
Hear Clear Enable Lines Conguration Logic State
Name IC Enable Flutter Fighter Enable LO Clamp Disable LO Clamp Disable HCI Disable LO Clamp Disable
Ref. Des UC350-C4 UC350-E3 UC350-A5 UC350-C2 UC350-B6 UC350-D1
Set By 9V3 U000-A2 U200-A2 U200-A2 U200-A2 U200-A2
TX1 1 X 1 0 1 0
RX1 1 1 1 0 1 0
TX2 X X 1 X X X
RX2 0 X 0 1 0
TX1: transmit mode with carrier squelch, PL or DPL RX1: receive voice with carrier squelch, PL or DPL TX2: transmit mode with all other data HST/MDC/DTMF etc. RX2: refers to receive mode with all other data HST/MDC/DTMF Logic State X means either 1 or a 0, i.e. dont care. expander is to transpose the compressed audio back to normal audio. As with the compressor circuit, the expander circuit adjusts the amplitude of a signal based upon its input amplitude, NOT its frequency. The voltage transfer function is: EXPOUT= 0.41*(EXPIN/0.28)2. Example : 100 mV EXPIN == 52 mV EXPOUT 191 mV EXPIN == 191 mV EXPOUT 250 mV EXPIN == 327 mV EXPOUT NOTE This operation is NOT a function of frequency between 300 Hz and 3 kHz . Hear Clear Routing of Data/Signalling While transmitting, all data and signalling bypasses the Hear Clear Compressor. While receiving, subaudible signals PL/DPL go through the Flutter Fighter along with the audio, and is unaffected by the Flutter Fighter operation. On entering the ASFIC, the sub-audible signaling is separated from the voice and decoded. Sub-audible signaling never goes through the expander. While receiving, data and high speed signalling (not sub-audible), the Flutter Fighter is set to pass through mode. In this mode, the Flutter Fighter is routed from FF IN to FF OUT without any adjustment.
Accessory Connector Congurations

The configuration of the pins of accessory connector J400 can be changed to support different accessories by changing the settings of dual switch S401. S401 (pins 2-4) is turned ON if external Ignition Sense is not used, and turned OFF if an external Ignition Sense cable is installed. The operation of the Ignition Sense circuitry is described above in the Electronic On/Off and Ignition sections of the Controller Detailed Functional Description. S401 (pins 1 and 3) is turned ON to support Remote Desk Set, Public Address and External Alarm, and is turned OFF to configure the accessory connector for External Data Modem applications. NOTE The radio is shipped with Ignition Sense disabled. and Remote Desk Set, Public Address and External Alarm enabled. Remote Desk Set For Remote Desk Set applications, switch S401 (1-3) should be ON. This pulls the analog switch control line U402-9 low, and the switch positions of U402 are as shown in the schematic. The PTT signal from the desk set at U400-3 is routed via U402-4 and 2 and via U203 1 and 2 (U203 is ON since pin 4 is high via R433 and R431) to P port U101-22. The hook signal at U400-14 is inverted by Q101 and applied to P port U101-23. Transmit audio at U400-2 (EXTERNAL_MIC_ AUDIO) is connected in parallel with the front panel mic audio input and applied to ASFIC U201-B8. DC bias required by microphone is provided by R204 and R205. GATED_RX_AUDIO which is de-emphasized and controlled by the squelch mute gate is obtained from
8-16
6880906Z19-O
September, 2000
ASFIC U201-H5, buffered and amplied by U403 and sent to the desk set at J400-11. Public Address Public address operation requires an accessory HLN9322 Public Address Switch Box and one or more HSN1000 amplified speakers. In the Public Address mode, the radio functions simply as a junction box which routes microphone audio from the front panel connector directly to the switch box via J400-2, where it is further amplied and routed to the amplied speakers. Additionally, the microphone PTT does not key the transmitter, and the microphone off-hook condition is ignored, appearing to be on-hook. For Public Address operation, switch S401 (1-3) should be ON. This pulls the analog switch control line U402-9 low, and the switch positions of U402 are as shown in the schematic. When Public Address mode is turned on using the Switch Box, the switch box pulls J400-12 low. This signal is passed through switch U402 from pin 14 to 15, which also goes low. The hook line is pulled low by D401, forcing the microphone to appear on-hook. The control line to gate U203-4, normally high via R433, is pulled low, turning off U203 and preventing MIC PTT from being applied to the P. Thus, microphone audio is routed to the public address speakers but the radio does not transmit, and receiver operation is maintained in the same condition it was when the microphone was on-hook. SW_B+ from J400-9 is supplied to the switch box, where it powers the internal amplier stages and also turns on a rely which applies battery voltage to the external amplified speakers. Thus, when the radio is turned off, all PA circuits and amplified speakers are turned off as well. External Alarm For External Alarm installations, switch S401 (1-3) should be ON. This pulls the analog switch control line U402-9 low, and the switch positions of U402 are as shown in the schematic. When the radios alarm mode is enabled and the proper code has been received, ASFIC port U201-A3 goes high, turning on Q411 via U402-(11-13) and R411, saturating Q411 and pulling J400-4 low. For External Alarm installations, switch S401 (1-3) should be OFF. This pulls the analog switch control line U402-9 high via R442, and the switch positions of U402 are the opposite from those shown in the schematic. Data Modem For Data Modem installations, switch S401 (1-3) should be OFF. This pulls the analog switch control line U4029 high and the switch positions of U402 are thrown opposite of that shown in the schematic.
NOTE All Data Modem I/O functions are active low, 0 VDC. The reconfigured pin functions of accessories connector J400 are as follows: J400-12 is an input to the radio which allows the data modem to mute the radios speaker audio while data bursts are being received. The modem pulls J400-12 low, which is routed through switch U402 from pin 14 to 1, and turns on Q415 and, therefore, Q401. This pulls U401-8 low, muting the audio power amplier. J400-4 is an output from the radio which tells the modem that the radio is transmitting by pulling J400-4 low. Two non-simultaneous conditions are summed to recognize transmit mode under all timing conditions. If PTT is low, Q410 is off and a high is provided via R440, D403, U402 pins 12-13, and R411, to turn on Q411 and pull J400-4 low. If the transmit-enable voltage K9V1_ENABLE is high, a high is provided via D403, U402 pins 12-13, and R411, to turn on Q411 and pull J0400-4 low. J400-15 provides system busy indication by observing the status of the AUDIO_PA_ENABLE line, which is low during active receive conditions. This low is provided to J400-15 via D402, indicating a signal is being received. J400-3 is DATA_PTT input to the radio, routed via switch U402 pins 4 to 3, to U101-8. The ASFIC (U201) is congured for FLAT_TX_AUDIO when DATA_PTT is asserted at U101--8. J400-5 provides a FLAT_TX_AUDIO input to the radio, via C418 and gain-reduction buffer U202 (pins 1, 2, 3), to U201-D7. This connection is always provided and is not recongured by the setting of switch S401 (1-3). J400-11 provides a Flat/Unmuted RX Audio Output from the radio. This audio is obtained directly from detector U5201-28 via C230 and R236, is routed from U402 pin 10 to pin 5, amplied by U403 and applied to J400-11 via R419 and C419. RSSI Buffer For special applications, a DC voltage proportional to received signal strength can be provided to J400-15. This requires removal of resistor R430 and diode D402, and insertion of resistor R215. The DC signal-strength voltage is provided by detector U5201-11, buffered by U202 (pins 12, 13, 14), and routed via R215 to J400-15.
September, 2000
6880906Z19-O
8-17
8-18
6880906Z19-O
September, 2000
Section 9 Troubleshooting
Overview
This section contains six troubleshooting tables for the following GTX components: Receiver Synthesizer 12W/30W Power Amplier Controller Control Head
Troubleshooting Charts
September, 2000
6880906Z19-O
9-1
Troubleshooting Troubleshooting Charts
Start
Yes
Is AUDIO_DET AC level 0.1Vrms, 1KHz?
No
Check controller circuit.
Is RF_REG_5V present at Q5320 E-2? Yes Is K9.1 0 V at Q7420-C? Yes
No
Check DC circuit.
No
Check logic circuit.
NOTE: RF input level is -47dBm. All the levels indicated have a tolerance of 10%.
Check RX_INJ level.
<-50dBm
Check Rx/Tx switch.
>-50dBm Check LO_INJ level. >0dBm >-35dBm Check IF level on L5401. <-35dBm <0dBm Check synthesizer Circuit.
Check Y5201.
Yes
Is <-35dBm present on Y5201-3? No
Check Q5201.
Yes
Is <-20dBm prsent on Y5202-1? No
No
Is <-38dBm present at C5312?
Yes
Check Y5202.
Yes
Is <-22dBm present on Y5202-3? No
Yes
Is <-48dBm, No 45.1MHz, present at U5211-5?
Yes
Is DC present across R5302?
No
Replace U5211.
End
Replace Q5301.
Replace R5302.
Troubleshooting Flow Chart for Receiver 9-2

6880906Z19-O September, 2000
B Start
>-18 dBM Check RF level at C5208. Check RF & IF circuit.
>-18 dBM
Check 9.3 VDC at U5201-13. 9.3V
<9V
Check DC circuit.
Check DC at C5251.
<4.7V
Check DC circuit.
5V Check ADAPT at U5201-22. >1V
Check control circuit.
OV -3 dBm 2dB DIFFERENCE BETWEEN IN & OUT Is RF level on Y5211 at 44.645MHz? Yes -13 dBm 2dB DIFFERENCE BETWEEN IN & OUT Is RF level No on FL5201 IN & OUT at 455KHz? Yes -3 dBm 2dB DIFFERENCE BETWEEN IN & OUT Is RF level No on FL5202 IN & OUT at 455KHz? Yes Check U5201. Troubleshooting Flow Chart for Receiver (cont.)
September, 2000 6880906Z19-O
No
Check Y5211 circuit.
Check FL5201 circuit.
Check FL5202 circuit.
9-3

SYNTHESIZER DEVIATION Start
Controller
No
Is AUDIO MOD present at C5700? Yes Is there 212mV on C5750? Yes Check synthesizer loop lter.
No Replace U5702.
SYNTHESIZER PENDULUM Start
Is 2.1 MHz present at R5731? No
Yes
Replace R5731.
Is 16.8 MHz present at U5700-10? No
Yes
Is 16.8MHz present at U5700-10? Yes Replace U5702.
No
Check C5733 and R5715.
Yes Replace U5700.
Is 5V present at U5700-13? No Yes Replace L5700.
Is 5V present at L5700? No
Is 5V present at U5703-2? No No Is 9.3V present at U5703-1?
Yes
Check L5704.
Check C5738, C5724, C5713, L5709.
Yes
Replace U5703.
Troubleshooting Flow Chart for Synthesizer 9-4

6880906Z19-O September, 2000
NO Tx INJECTION
Start
Is 5V present at Q5707-C?
Check Q5707 DC circuit.
Is 2.1 MHz present at R5731?
Check Q5701 and Q5705 DC circuits.
Check RF path line-up.
Troubleshooting Flow Chart for Synthesizer (cont.) 9-5
September, 2000
6880906Z19-O
START
Yes
Is Red light on?
No
Is control head OK? Yes Yes
No
Go to control head troubleshooting.
Is K9.1 OK?
No
Is there 5V at K9.1 ENB? Yes Is there 9.3V at Q741 or Q742? Yes
No
Go to controller troubleshooting.
No
Replace Q741 and Q742.
No
Is PA control at ~0V?
Yes
Go to synthesizer troubleshooting.
No
Is TX_INJ >2dBm? Yes
Is there 5V at PA_ENABLE? No
Yes
PA RF SECTION FAULT
PA LOGIC SECTION FAULT
Check CR6501, Q6506, Q6501, L6503, L6502.
No
Is RF at U6501 ~2dBm? Yes
Is there ~2V No at U702-2 (PA_PWR_SET) ? Yes No
Faulty power setting DAC or software
Check U6502, R6520, L6519, L6504 ,L6505, L6506,VR6501.
No
Are voltages at U6501* OK? Yes
Is there ~ 0V at U701-7? Yes Is U701-14 at <4.5V? Yes Is U701-1 at <4.5V? Yes Is U701-10 ~4.6V? Yes Faulty integrator. Replace U701.
Faulty coupler. Check CR6509, R6515, CR6506, R6514, L6516, R6512.
No Replace U6501.
Is RF at U6501 output ~24dBm? Yes
No
Check R6519, U701, L6515, R725, R721, R722, R723.
Check CR6502, CR6503, CR6504, R6538, R6539, R6537.
No
Is RF after Tx switch at ~24dBm? Yes
No
Faulty current sense mechanism. Check R6520, U701 DAC (U702-11).
Check L6513, L6513, C6543.
No
Is RF after Harmonic Filter at ~23dBm? Yes Replace Antenna connector.
No
Faulty REF voltage. Check R251, R252, U251.
RF Levels were measured with an RF probe in series with 0.5pF capacitor.
*U6501 DC voltages: Pins 3 and 4: A+-0.1V Pin 2: 9.1V (during Tx only)
Troubleshooting Flow Chart for 12 W Power Amplier 9-6

6880906Z19-O September, 2000
START
Yes
Is Red light on?
No
Is control head OK? Yes Yes
No
Go to control head troubleshooting.
Is K9.1 OK?
No
Is there 5V at K9.1 ENB? Yes Is there 9.3V at Q741 or Q742? Yes
No
No
Replace Q741 and Q742.
No
Is PA control at ~0V?
Yes
No
Is TX_INJ >2dBm? Yes
Is there 5V at PA_ENABLE? No
Yes
PA RF SECTION FAULT
PA LOGIC SECTION FAULT
Check CR6501, Q6506, Q6501, L6503, L6502.
No
Is RF at U6501 ~2dBm? Yes
Is there ~2V No at U702-2 (PA_PWR_SET) ? Yes No
Faulty power setting DAC or software
Check U6502, R6520, L6519, L6504 ,L6505, L6506,VR6501.
No
Are voltages at U6501* OK? Yes
Is there ~ 0V at U701-7? Yes Is U701-14 at <4.5V? Yes Is U701-1 at <4.5V? Yes Is U701-10 ~4.6V? Yes Faulty integrator. Replace U701.
Faulty coupler. Check CR6509, R6515, CR6506, R6514, L6516, R6512.
No Replace U6501.
Is RF at U6501 output ~24dBm? Yes
No
Check R6519, U701, L6515, R725, R721, R722, R723.
Check C6555, CR6502, CR6503, Q6505.
No
Is RF after Tx switch at ~24dBm? Yes
No
Faulty current sense mechanism. Check R6520, U701 DAC (U702-11).
Check H6502, L2,L3,L4.
No
Is RF after Harmonic Filter at ~29dBm? Yes Replace Antenna connector.
No
Faulty REF voltage. Check R251, R252, U251.
RF Levels were measured with an RF probe in series with 0.5pF capacitor.
*U6501 DC voltages: Pins 3 and 4: A+-0.1V Pin 2: 9.1V (during Tx only)
Troubleshooting Flow Chart for 30W Power Amplier

September, 2000 6880906Z19-O
9-7
Start
Apply power to radio and turn on.
No/Dont know
Are alert tones enabled with RSS?
Was good or bad power-on beep present?
Yes
Yes
Use RSS to enable tones. Was good power-on beep present? Yes Are alert tones enabled with RSS? End No Check radio connection to RIB and computer.
No
Reprogram radio with RSS. Apply power to radio and turn on.
Yes
No
Was good poweron beep present?
Yes Main radio board must be replaced. No RIB/radio connections OK? Done No With power connected to radio and the radio turned on, check the following: 1) 5 V at pin 1 of U631 and pin 71,12,31,41 of U101. 2) Check for 14.7456 MHz at pin 73 of U101. 3) Check DC at pin 75 of U101. If < 4.5V DC check C202 for 2.1 MHz signal. 4) Check for typical voltages of U101 and U201. Done
Yes
Are tones present on power up at U202, pin 8?
Yes Audio problem. Troubleshoot audio circuitry. Done
Troubleshooting Flow Chart for Controller
9-8
6880906Z19-O
September, 2000
Start
Is the display on? Yes
No
Is SPI communication OK? No
Yes
Check LCD, U932, Q953, and ZEBRA connectors.
Check controller.
No Do the LEDs light?
Check U941, Q942-4, D942-4.
Yes No Is backlight OK?
Check U941, Q951, Q952,D951-D970.
Yes No Is volume OK? Check U942, and U970.
Yes No
Check R915-922, R955, and R958.
Is keypad OK? Yes End
Troubleshooting Flow Chart for Control Head

September, 2000 6880906Z19-O
9-9
9-10
6880906Z19-O
September, 2000
PA_CNTR CONTROLLER
LOCK_DET CURRENT_SENSEPEND_CE ADAPT MOD_IN SPI_CLK RSSI DET_AUDIO SPI_DATA DAC_CE DAC_CE VAG FLT_A+ K9.1_ENABLE SW_B+ PA_ENABLE TEMP PA_TEMP K9V1_ENABLE SPI_CLCK_SRC SPI_CLCK_SRC SPI_DATA_SRC PA_ENABLE SW_B+ 2_1MHZ FRACN_CE SPI_DATA_SRC VAG 9V3 VFORWARD TEMP PA_CNTRL K9.1 9V3 CURRENT_SENSE+
PA
FLT_A+ K9.1 CURRENT_SENSEPA_TEMP PA_CNTRL
CURRENT_SENSE+ RX_IN VFORWARD PA_K9.1 TX_INJ
SYNTH
9V3 2.1MHZ K9.1 LO_INJ MOD_IN RF_REG_5V PEND_SEL SPI_CLK SPI_DATA SYNT_LOCK SYNT_SEL TX_INJ
RX
9V3 ADAPT K9.1 DET_AUDIO LO_INJ PA_K9.1 RF_REG_5V RSSI RX_IN
Schematic Diagram for HLF9003A, HLF9004A, HLF9009A & HLF9010A Main Boards, Radio Block Diagram Section
September, 2000
6880906Z19-O
RF_REG_5V
LO_INJ
K9.1 9V3 5R R5230 47K FL5201 1 RF_REG_5V LNA SHIELD MIXER SHIELD 5R IN 455KHz GND 2 OUT 3 1 IN FL5202 455KHz GND 2 OUT 3
9V3
R5311 13K
C5321 39PF
C5326 0.01UF
R5302 220
Q5230
RF_REG_5V
C5323 0.01UF R5312 13K L5321 4.2NH L5302 6.8n R5306 150 C5310 39PF C5311 0.01UF
R5325 390 R5322 10 C5224 R5240 K9.1 100 1500PF C5231
K9.1
PA_K9.1
K9.1
R5324 L5322 390 68NH C5312 C5325 0.01UF C5308 Q5301 6.8pF 3 D5303
4 MIXER_OUT 3 IF_AMP_IN 36 35 IF_AMP_OUT LIM_IN
DET_AUDIO
0.47UF
RSSI
3pF
33 32 DEMODE_FILT DEMOD_FILT 31 29 DEMOD_OUT AUDIO_IN
RX_IN
FL5203 938MHz IN OUT CASE
FL5204 938MHz IN OUT CASE
U5211 3
RF
R5241
MIXER
GND1 GND2 GND3 IF
2
6 5 PREAMP_IN PREAMP_OUT
ADAPT
AUDIO_OUT RSSI_OUT 28 11 25 23 20 22 15 18 30
6
LO
1 4 5 R5326 0NU R5321 220 C5322 39PF C5324 0.01UF R5323 300 R5327 0 R5328 0NU
C5223
8 7
MIXER_IN LO_IN OSC_OUT OSC_FB T_R
0.1UF
10 9
U5201 IFIC
RSSI_BYP SQ_LIM_OUT SQ_RECT_IN ADAPT SQ_OUT CHAN_DET RIPPLE_FILT SQ_TAIL_TC SQ_NOISE SQ_LIM_IN ICO_TUNE
RF_REG_5V
27 13 14 B+ 2.5V_REG 5V_REG1 5V_REG2 5V_REG 5V_REG3 DRIVE
1 C5214 3.9PF 9V3
GND
21 2 12 17 34
19 16 26 24
R5223 7.5K
C5235 39PF
C5239 39PF
C5234 0.1UF
L5401 0.47M IF AMP SHIELD C5204 R5204 5R 0.1UF R5205 2K R5202 33K C5203 R5231 R5203 6.8K Q5201 IN 15PF L5201 1200NH C5201 3PF R5201 13K C5206 .00 L5202 .00H C5205 20PF 0NU R5211 820 100 C5404 27PF L5402 0.47M C5200 22PF R5401 51
C5213 36PF
R5212 5.6K
C5227 4.7UF
R5224 13K
C5229 39PF
C5236 39PF
C5233 39PF
C5237 39PF
C5228 0.1UF
C5212 13PF
Y5211 44.6450M
C5226 .039UF
R5221 130K
C5225 3.3UF
Y5201 45.1MHz IN GND OUT C5202
0.1UF
RF_REG_5V Y5202 45.1MHz OUT GND 0 L5203 1.0UH C5207 .00 2 D5201 R5207 3 0.1UF L5211 1200NH C5208 C5211 16PF C5251 10UF C5252 0.1UF SH5201 SHIELD SH5202 SHIELD SH5203 SHIELD
Schematic Diagram for HLF9003A, HLF9004A, HLF9009A & HLF9010A Main Boards, Receiver Section 2
6880906Z19-O September, 2000
SW_RX C5727 0.1UF C5764 39PF 3 U5704 SW_RX 5V_REG
+V 2 AUX_OUT AUX_IN 1 NC GND 5
NC
C5709 100PF C5741 22NF C5765 39PF 8V5 R5739 51
C5701 0.1UF
C5705 39PF 8V5
L5705 150NH
SYNT_LOCK SPI_CLK SPI_DATA SYNT_SEL MOD_IN

C5743 22NF C5811 39pF C5729 0.1UF 5V_REG
C5763 39PF
L5707 1.0UH R5747 6.8K
R5702 0NU L5703 1.0UH VCC R5705 10K C5770 C5793 2.2pF R5746 10K C5703 1.6pF CR5702 OUT C5789 Q5702 2.4PF R5736 51 1 8 C5708 39PF L5706 150NH
C5760 39PF
C5726 0.1UF
C5715 4.7uF
R5711 4.7K
C5728 0.1UF
C5767 39PF 3 U5705 SW_TX
C5716 4.7uF
C5791 Q5706 U5707 M_LIN IN 1PF
C5788 100PF
U5701
NC
39PF
5V_REG C5766 39PF 5V_REG L5700 1.0UH 12-13.5V DC CR5700 TRIPLE_DIODE 6 C5722 0.1UF 30 31 32 1 2 3 4 C5754 1 5 C5755 2 4 C5756 3 C5723 0.1UF C5757 39PF C5718 4.7UF C5737 22NF 8 7 6 5 4 3 2 1 C5700 22NF C5762 39PF
GND 5
C5742 22NF
C5768 39PF
L5702 GND 1.0UH
2 3 4 6 7 C5759 39PF
C5792 2.2pF
R5745 180
R5703 10K
C5711 100PF
R5706 510
SW_TX
39PF
39PF C5802 0.1UF
39PF C5803 0.1UF 9
MODIN CEX CLK DATA GND4 DC5V3 LOCK AUX3
GND GND1 GND2 GND3 GND4
Q5700
+V 2 AUX_OUT AUX_IN 1 NC
C5790 2.7pF
INPUT OUTPUT
N.C. N.C. N.C. N.C. N.C. N.C. N.C.
R5737 22 R5738 R5717 C5710 100PF C5702 0.1UF C5707 39PF 22 C5761
PEND_SEL
NC
17 18 SUPFCAP 19 SUPFOUT 20 SUPIN 21 PREIN 22 GND1 23 DC5V1 24 DC5V2 TEST1
N.C. N.C. N.C. N.C. N.C. N.C. VDD
29 N.C. 28 N.C. 27 N.C. 26 YSSD|YSSA 25 S1 U5700 24 SS PENDULLUM 23 CE 22 SCK 21 S0
N.C. N.C. C_EXT DET DE F_OUT V_REG V_OPT VDD
5 6 7 8 9 10 11 12 13
R5715 2.2K
C5733
5V_REG
22NF C5804 0.1UF
NC NC
32 VMULT2 VCP 10 31 VMULT1 IADAPT 30 11 FREFOUT GND2 U5702 12 29 DC5V QFP_FRACTIONAL_N IOUT 28 13 MODOUT GND 14 27 XTAL1 CPB|AS1 15 26 XTAL2 CPB|AS2 16 25 WARP TEST2 NC R5708 200K NC 5V_REG 8V5 C5749 R5700 2.2K NU C5720 0.1UF C5750 R5709 200K
LO_INJ
39PF
2.7K
C5795 100PF R5716 2.4K C5745 10NF C5746 10NF C5747 10NF C5744 10NF R5701 R5742 6.8K 0NU R5729 150 R5741 10 C5783 R5734 51 C5736 NU U5706 M_LIN C5782 3.3pF L5701 1.200N 1.0UH CR5701 C5796 0.1UF C5797 0.1UF C5798 0.1UF C5799 0.1UF OUT GND C5704 1.8pF C5784 2.2pF R5744 180 2.4PF 8V5 IN Q5704 C5787 100PF C5775 39PF C5719 4.7uF C5794 39PF R5740 51 R5748 22
K9.1
5V SQ WAVE (1.05MHz) C5734 22NF C5752 39PF C5753 39PF C5751 33NF C5735 22NF
20 19 18 17 16 15 14
9.3V
R5719 0NU R5712 4.7K
R5720 0NU
R5721 0NU
R5722 0NU
R5723 0NU
R5724 510
R5725 510
R5726 510
R5727 510
C5721 0.1UF R5731
5V_REG
1.2pF
C5785 2.2pF R5743 10K C5786
C5810 39PF L5708 150NH R5754 330 R5752 330 C5778 39PF R5713 4.7K Q5701
C5730 0.1UF
C5774 39PF
2.1MHZ
100 C5769 39PF
C5712 10UF C5805 0.1UF C5806 0.1UF C5732 22NF C5717 4.7uF
R5707 3.3K
C5748
TX_INJ
0.01UF R5714 2.7K
RF_REG_5V
9.3V 5V_REG U5703 L5709 C5772 O GND 3 C5738 22NF C5724 0.1UF C5713 10UF C5725 0.1UF 2 L5704 1.0UH C5739 22NF C5714 4.7uF C5740 22NF C5758 39PF MIMIC LINE UP SWITCH VCO E5700 SHIELD E5703 SHIELD E5702 SHIELD E5701 SHIELD E5704 SHIELD 39PF Q5703
R5728 330
C5771 39PF
R5704 330
Q5705
R5710 10K C5773
C5706 39PF
R5750 2.7K Q5707
C5814
R5755 22
C5779
9V3
39PF R5756 270
39PF R5757 270 C5776 39PF C5731 0.1UF
560NH
R5735 51 R5732 100 R5733 100 R5751 2.7K C5813 39PF R5753 33
39PF R5718 1.5K
Schematic Diagram for HLF9003A, HLF9004A, HLF9009A & HLF9010A Main Boards, Synthesizer Section
September, 2000
6880906Z19-O
C6549 0.1UF L6517 Q6506 C6501 0.1UF R6540 C6533 39PF C6550 0.1UF C6507 0.1UF 100 C6505 39PF L6503 68nH 1 L6502 7.66NH U6501 MHW2821-2 RF_INPUT RF_OUTPUT 3 +DC|SUP. 4 +DC|SUPP. +DC|BIAS C6506 R6505 10 R6504 560 R6506 560 R6532 100K C6508 C6509 C6510 R6509 0.01UF L6501 68nH 0.01UF 0.01UF 100K C6554 C6511 C6512 C6513 39pF 0.1UF 0.1UF 0.1UF R6508 4.7 C6526 39PF C6564 1000pF R6503 2 1 CR6501 NC 10 C6503 39PF L6504 L6505 L6506 1UF 1UF 1UF C6538 .01uF C6565 0.1uF C6553 1uF MA4P1250 L6511 C6523 7.5pF C6545 .01uF C6546 0.1uF C6552 1uF C6566 0.1uF C6548 .01uF C6519 39pF R6531 22 R6530 39 3 LAMBDA/4 Line R6515 3.3K L6521 3.85nH L6508 57R01 L6510 57R01 GND 6 39PF C R6526 C6520 2.2pF R6528 560 C6502 1.2pF L6507 2.5nH B E C MRF8372 Q6501 E E E 39pF C6551 NC C6529 39PF 2 1 CR6509 GND1 7 5 2 C6563 2.7pF C6542 10pF L6513 4.2NH C6567 12pF C6539 10pF C6541 10pF Q6505 C6568 12pF C6540 12pF 1 R6514 100K C6555 GND OUT 2 130pF 1000PF CR6502 C6525 L6512 23.75NH This inductor (L6520) is to prevent build-up of electro-static charge at the output. H6502 07L01 1
RFOUT GND VFRWD SWDC RCVR
PA_CNTRL
68nH
H6501 04H03 IN
J6501 ANTENNA CONNECTOR 3
MA4P1250
L6523 82nH
L6509 82nH
L6522 82nH C6522
4 5 6 2
L6516 68nH C6535 39PF
TX_INJ
10 R6527 560
VFORWARD
.01uF
R6523 1.5K R6524
C6514
C6515
C6516
CR6503
K9.1
1.5K R6525 C6532 39PF 1.5K C6517 3 39PF NC VR6501 12V R6555 220 SH6501 SHIELD CR6508 2 1 1.639m R6520 3 4 C6537 39PF 39PF C6518
PA_K9.1
68nH
RX_IN
L6515
CURRENT_SENSER6519 47K
68nH C6534 39PF
PA_TEMP
3 2
U6502
24V L6518 57R01 L6519 57R01
+V 1 C6524 .022uF NC AUX_OUT AUX_IN 1 NC GND 5 L6514 68nH 4
C6571 39PF
C6569 0.1UF C6570 39pF
CURRENT_SENSE+
Power Connector
FLT_A+
Schematic Diagram for HLF9003A & HLF9004A Main Boards, Power Amplier Section 4
6880906Z19-O
September, 2000
C714 R711
VAG
22K R705 560 C702 39PF R702 2.4K 6 5 11 C701 39PF U701 LM2902 SW_B+ 4 7 C711
.00 R712 0 SW_B+ 9 10 11 U701 LM2902 4 8
C703 39PF R704 22K
0.1uF
R713
VFORWARD
PA_CNTRL
510 C712 0.1uF
SW_B+ C727 R728 100K R729 100K R717 SW_B+ 10K CR721 R714 100 VAG U701 LM2902 1 3 11 R716 10K R715 4 2 C713 39PF 1K R719
SW_B+ TEMP
0.1uF R726 10K C724 0.1uF R727 22K
R706 100K C726 39PF C723 39PF
R703 22K
R718 10.0K
CURRENT_SENSE-
CURRENT_SENSE+
1K R720 10.0K C722 39PF 11 R722 12 13 R723 100K 0.1uF U702 16 MC144111 VDD 2 Q1-OUT 4 Q2-OUT 11 Q3-OUT 13 Q4-OUT 3 R1-OUT 5 R2-OUT 12 R3-OUT 14 R4-OUT DOUT VSS 7 15 2.2K R734 4.7K 14 4 LM2902 U701 R724 3.3K C731 PA_PWR_SET R740 9V3 R731 100K R730 100K
9V3
9V3
R725 10K
R721 5.6K
PA_TEMP
22K C725 39PF
SPI_DATA_SRC DAC_CE SPI_CLCK_SRC

NC NC
DIN
6 10
NC NC NC NC NC NC R732 4.7K R733 4.7K
ENABLE_ CLOCK
8 NC1 9 NC2
R736
PA_ENABLE
4.7K R737 4.7K
Q731
9V3 R741 Q741 Q742 1.5K
K9.1 K9.1_ENABLE
R742 1.5K R743 1K C741 39PF
Schematic Diagram for HLF9003A & HLF9004A Main Boards, Power Control Section
September, 2000
6880906Z19-O
C6549 0.1UF L6517 Q6506 C6501 0.1UF L6503 C6533 39PF C6550 0.1UF C6505 39PF C6507 0.1UF L6502 7.66NH C6506 R6506 22 R6502 22 R6538 47 C6508 C6509 C6510 C6560 3.3pF 0.01UF 0.01UF 0.01UF 1 R6523 1.5K R6524 R6503 10 2 1 CR6501 NC C6514 C6503 39PF 1UF 1UF 1UF C6515 C6516 0.1UF 0.1UF 0.1UF L6519 C6529 39PF R6514 3.3K R6515 3.3K NC 2 CR6509 C6517 R6537 47 39PF 3 C6523 15pF 1 C6511 C6512 C6513 CR6508 J6502 POWER CONNECTOR C6526 2 (+) (-) LAMBDA/4 Line C6562 30pF NC CR6506 R6539 47 R6504 510 R6505 1K 68nH U6501 MHW2821-2 1 RF_INPUT RF_OUTPUT 3 +DC|SUP. 4 +DC|SUPP. +DC|BIAS GND 6 GND1 7 CR6502 5 7.66NH 2 L6507 82nH 23.75NH 1000PF L6508 MA4P1250 C6525 C6542 1.8PF C6540 3.9pF C6541 1.8PF 7.66NH 39PF C6551 1.5pF L6513 C6553 3.3PF L6518 C6552 1.5pF C6543 Microstrip Coupler J6501 ANTENNA CONNECTOR This inductor (L6520) is to prevent build-up of electro-static charge at the output.
PA_CNTRL
68nH
Coplanar Match R6526 B B C6502 5.6PF
39PF C C Q6501 MRF8372 E E E E
R6532 100
R6531 100
R6512 100
L6520 82nH
TX_INJ
10 R6527 560 R6528 560 L6501 68nH
K9.1
1.5K R6525 C6532 39PF 1.5K
10PF C6535 39PF L6516
FLT_A+
C6519 39PF
CR6503
VFORWARD
MA4P1250 L6511 68nH 68nH 3 L6504 L6505
L6506
CURRENT_SENSE+
C6518 1 39PF R6520 1.639m 2 C6536 39pF LAMBDA/4 Line R6519 47K
L6515 68nH C6534 39PF
PA_TEMP
CURRENT_SENSEC6537 39PF C6527
NC
VR6501 12V R6555
RX_IN
39PF CR6504
220 3 U6502 +V AUX_OUT AUX_IN 1 NC GND 5 L6514 68nH 2 4 C6520 10pF C6538 39PF C6544 0.1UF C6545 39PF C6546 0.1UF L6509 68nH
PA_K9.1
C6524 22NF
NC
Schematic Diagram for HLF9009A & HLF9010A Main Boards, Power Amplier Section 6
6880906Z19-O September, 2000
C714 R711
VAG
22K R705 3.3K C702 39PF R702 22K 6 5 11 C701 39PF U701 LM2902 SW_B+ 4 7 C703 39PF R704 22K C711
39PF R712 2.2K SW_B+ 9 10 11 4
22NF
VFORWARD
8 U701 LM2902
R713
PA_CNTRL
510 C712 0.1uF
SW_B+ C727 R728 100K R729 100K R717 SW_B+ 3.74K 4 1 3 100 VAG U701 LM2902 11 R716 3.74K R715 2 C713 39PF 1K
SW_B+ TEMP
0.1uF R726 10K C724 0.1uF R727 22K
R706 200K C726 39PF CR721 R714 C723 39PF
R703 22K
R718 10.0K R719
CURRENT_SENSE-
CURRENT_SENSE+
1K R720 10.0K C722 39PF 12 13 R723 100K 0.1uF U702 16 MC144111 VDD 2 Q1-OUT 4 Q2-OUT 11 Q3-OUT 13 Q4-OUT 3 R1-OUT 5 R2-OUT 12 R3-OUT 14 R4-OUT DOUT VSS 7 15 2.2K R734 4.7K 11 14 4 LM2902 U701 R724 3.3K C731 PA_PWR_SET R740 9V3 R731 100K R730 100K
9V3
9V3
R725 10K
R721 5.6K
R722
PA_TEMP
22K C725 39PF
SPI_DATA_SRC DAC_CE SPI_CLCK_SRC

NC NC
DIN
6 10
NC NC NC NC NC NC R732 4.7K R733 4.7K
ENABLE_ CLOCK
8 NC1 9 NC2
R736
PA_ENABLE
4.7K R737 4.7K
Q731
R741 Q741 1.5K
9V3 Q742
K9.1 K9.1_ENABLE
R742 1.5K R743 1K C741 39PF
Schematic Diagram for HLF9009A & HLF9010A Main Boards, Power Control Section
September, 2000
6880906Z19-O
SPI_DATA_SRC K9V1_ENABLE SPI_DATA LOCK_DET PEND_CE ADAPT MOD_IN SPI_CLK 2_1MHZ SPI_DATA LOCK_DET PEND_CE ADAPT MOD_IN SPI_CLK 2_1MHZ HIGH_LOW_BAND DET_AUDIO RSSI FRACN_CE DET_AUDIO RSSI FRACN_CE SCI_TX INT_SPKR+ INT_SPKRFILTERED_AUDIO ASFIC_MIC_AUD_OUT HC_CNTL EXP_AUDIO DISC RSSI RX_IN TX_IN 9V3 FLT_A+ FLAT_TX_AUDIO PTT HOOK_RSS GATED_RX_AUDIO RSSI_BUF RX_AUDIO AUDIO_PA_ENABLE IGNITION_SENSE FLAT_TX_AUDIO PTT HOOK_RSS GATED_RX_AUDIO RSSI_BUF RX_AUDIO B+_CONTROL 9V3 +5V FLT_A+ SW_B+ FILTERED_AUDIO EXTERNAL_ALARM ASFIC_MIC_AUD_OUT BUS+ EXP_AUDIO PUBLIC_ADDRESS RX_IN DATA_PTT TX_IN MIC EXTERNAL_ALARM BUS+ PUBLIC_ADDRESS DATA_PTT MIC SPI_CLCK_SRC PA_ENABLE TEMP VAG DAC_CE FLAT_RX_AUDIO FAST_OFF_IGN VPP FLAT_RX_AUDIO FAST_OFF_IGN VPP K9V1_ENABLE SCI_TX INT_SPKR+ INT_SPKRVAG
SPI_DATA_SRC K9V1_ENABLE SPI_CLCK_SRC PA_ENABLE TEMP VAG DAC_CE
HEAR_CLEAR
ON_OFF_CONTROL B+_CONTROL RESET BATTERY_VOLTAGE +5V USW_+5V_CL 9V3
9V3
FLT_A+ SW_B+
AUDIO_PA_ENABLE IGNITION_CONTROL IGNITION_SENSE
AUDIO_&_DIGITAL
AUDIO_PA_&_I/O
SUPPLY_VOLTAGE
USW_+5V_CL +5V BATTERY_VOLTAGE RESET FLT_A+
IGNITION_CONTROL 9V3 SW_B+
B+_CONTROL ON_OFF_CONTROL
Schematic Diagram for HLF9003A, HLF9004A, HLF9009A & HLF9010A Main Boards, Controller Block Diagram
6880906Z19-O
September, 2000
+5V
J100
TP103
9 17 18 15 4 16 14 10 11 13 12
U203 5
+5V FLT_A+ ON_OFF_CONTROL BUS+ PTT MIC HANDSET_AUDIO ANALOG_1 ANALOG_2 ANALOG_3 LED_CE INT_SPKR+ INT_SPKRSPI_CLCK_BUF
L418 L419 L420 L421 L422 L423 L424 L425 L426 L427 L428 L429
FLT_A+
+5V FLT_A+
+5V
K9V1_ENABLE
R109 270 R110 270 C104 .01uF
+5V
PTT
VDD VSS CNTL 3 4
R100 2 4.7K R101 200K R102 200K R103 200K C113 C114 C105 .01uF .01uF 3.3uF
PA_ENABLE
TP133
ON_OFF_CONTROL
SCI_RSS MIC HANDSET_AUDIO
C106 R106
+5V
PUBLIC_ADDRESS
R132
D102 VPP VAG
10K R104
0.1uF C111 22K R133
0 1 2
C109 39pF
C110 39pF
VAG
C132 1uF
+5V 9V3
+5V
LED_CE
+5V C101 0.1uF C102 0.1uF C103 0.1uF
47K
.01uF C131 0.1uF
100K
INT_SPKR+
L430
R122 9 8 U106 10 47K
VAG 9V3
+5V
INT_SPKRL431 L432
AN_3_OFF C133
R147
NC
4 6 U106 5 +5V
R105 4.7K
1 2 PD3_MOSI PD4_SCK
IN IN IN IN IN
NC
+5V
R251
9V3
2 1 3 U251
8 270 VCC
34
0.1uF VCC
28 20 EN_CS EN_OE EN_WE 22 27 10 A0 U103 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 GND 14 A14 9 8 7 6 5 4 3 25 24 21 23 2 26 1
0 1 2 3
47.5K NC NC 5 U202 7 6 R252 47.5K NC
41
22
23
24
25
26
27
28
29
74
12
31
71
51
50
73
SPI_DATA_BUF
IN
IN
IN
PH5_CSGP1
PH6_CSGP2
PH0_PW1
PH1_PW2
PH2_PW3
PH3_PW4
PH4_CSIO
VRL
VDD
VDD
VDD
VRH
PG6
PH7_CSPROG
AVDD
XTAL
C644
C645
C646
C647
C652
C648
C649
C651
EXTAL
C650
R114 SQDET 68K
C147 .00
62
0 1 2 3 4 5 6 7 0 1 2 3 4 5 6
30 32 7 EN_CE EN_OE EN_WE 20 19 18 17 16 15 14 13 3 2 31 1 12 4 5 11 10

AM28F010-120
39PF
39PF
39PF
39PF
39PF
39PF
39PF
39PF
39PF
14 11 VCC U106 GND 12
BATTERY_VOLTAGE TEMP
RSSI
3 4 5 6
R107 2.2K
R108 10K
R127 4.7K
72 NC 61
30 75
E IRQ XIRQ RESET PD5_SS

PG7_R_W
PC0_DATA0 PC1_DATA1 PC2_DATA2 PC3_DATA3 PC4_DATA4 PC5_DATA5 PC6_DATA6 PC7_DATA7
11 12 13 15 16 17 18 19 IO1 IO2 IO3 IO4 IO5 IO6 IO7 IO8
63A21
C252 10uF
C253 1uF
63 64 65 66 67 68 69 49
A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16
U102
D0 D1 D2 D3 D4 D5 D6 D7 A17 VPP
21 22 23 25 26 27 28 29 6 9
0 1 2 3 4 5 6 7
1 2 3 4 5 6 7
R113
13
LOCK_DET
LCD_CE 33K C100 39PF C108 .001uF
L433
LCD_CE_BUF HOOK_RSS GND
IGNITION_SENSE RESET
3
33 77 60
0 1 2 3
MODA_LIR
+5V PF0_ADDR0 PF1_ADDR1 PF2_ADDR2 PF3_ADDR3 PF4_ADDR4 PF5_ADDR5 PF6_ADDR6 PF7_ADDR7 PB0_ADDR8 PB1_ADDR9 PB2_ADDR10 PB3_ADDR11 MODB_VSTBY
U101 68HC11K1_QFP
68HC11K4_TAU
+5V
4 5 6 7 8 9 10
EEPROM_X25040
L434
3 +5V 7 C643
C151 0.1uF
59 58 57 56 55 54 53 21 20 19 18 17 16 15
0 1 2 3 4 5 6 7
7 8 9
PE0_AN0 PE1_AN1 PE2_AN2 PE3_AN3 PE4_AN4 PE5_AN5 PE6_AN6 PE7_AN7
39PF
C642 39PF
48 47 46 45 44 43 42 40 39 38 37 36 35
8
+5V
5 2
VCC SI SO HOLD_ 7
C134 0.1uF
R111 4.7K
R112 4.7K
4 5 6 7
R117 0NU
10 11 12 13 14 15
11 12 13 14
R134 0NU R131 4.7K
1 CS_ U104 6 3 WP_ SCK VSS 4
HOOK_RSS
Q101
8 9 10 11
PG0_XA13 PG1_XA14 PA6_OC2_OC1 PA5_OC3_OC1 PA4_OC4_OC1 PA7_PA1_OC1 PA3_IC4_OC5 PG2_XA15 PD1_TxD PD2_MISO PD0_RxD PA2_IC1 PA1_IC2 PA0_IC3 PG3_XA16 PG4_XA17 PG5_XA18
3
14 15 16 17
16 17
R136 GND 24 10K
R155 47K
C107 .01uF +5V
+5V
+5V
12 13
PB4_ADDR12 PB5_ADDR13 PB6_ADDR14 PB7_ADDR15
U106
VSS
VSS
VSS
NC
R116 10K R145 10K
14
AVSS
NC
+5V
C135
SPI_CLCK_SRC SPI_DATA_SRC
76
32
52
70
78
79
10
13
11
80
0.1uF
R115 10K Q103
16 VCC
L131 270nH
SPI_DATA
1 2
Q102
+5V
A0 A1
74HC138A
U105
Y0 Y1 Y2 Y3
15 14 13 12 11 10 9 7
L132 NC 270nH
SPI_CLK
3 R135 10K
R200
A2
D101
9V3
6 4 5
DAC_CE FRACN_CE
LED_CE Q141 LCD_CE C136 C137 39PF 39PF R142 10K
CS1 CS2 CS3 GND 8
Y4 Y5 Y6 Y7
VPP
VR101 10V Q200 10K D200 NC C200 R222 47K C229 0.1uF +5V
PEND_CE
L200 33uH C228
.1uF C227
R146 270
C146 24PF
+5V
R121
USW_+5V_CL
4.7K
47UF R223 47.5K 33pF C234 R233 R232 68K VAG C221 0.1uF 9 10 U202 8 10uF R231
R150 +5V 9V3
.01uF
C233
FAST OFF CIRCUIT: POT DETECTOR

C254
DATA_PTT SCI_TX BUS+

+5V 33uF C225 .01uF C223 R221 0 R153 33K R123 10K
0.1uF
47K
10K 0.1uF
0NU C232 HANDSET_AUDIO

+5V
VCC
7
B+_CONTROL R152 Q150 2K
AN_3_OFF 5
R151
U251
MC33072D
200K
4 VEE
C222
SQDET
R126 10K
RESET
1uF
SCI_RSS
CR151 NC 0.1uF C226
4.7uF
C224
R237 68K
R238 68K 2 VPOS U204 NC 4 5
CR150
NC
C202
COM 6 C5 D6 H1 H3 A5 H2 B2 B6 E7 F8 J3 J2 1 IN MDCREF UPCLK XTALOUT PLLIM RXLIMOUT RXAUDOUT UNATRXOUT MICAMPOUT VOXO DACO REFATN PREMP VAGOUT VCOATN GCB0 GCB1 GCB2 GCB3 GND11 GND12 GND10 GND13 GCB4 GCB5 A4 G4 J4 H5 A6 C6 F7 G7 C8 D8 H8 B5 A3 B4 B3 A2 C4 C243 NC NC NC NC NC 39PF C242 B1 D1 E2 NC 39PF .033uF C241 GND 3 C237 NO
C2
DCAP
LOOPCAP
TIMINGCAP
LOWSPCAP
VAGCAP
RXLIMCAP
BIASRES
LCAP
SQDET
UNIVIO
BUFFDISC
CHACT
2_1MHZ
9V3
C1
35U45
VDD
R204
R205 1K C209 10uF
R206 470 C210 .022uF
C211 C201 39PF
470pF
F1 C3 E1 G1 G2 F2 E3
RESET
CLK PLCLK XTALIN TRKCLKIN DTMFCLK PGMENAB DATA EXTVOLIN EXPAUDIO RXIN AUXRXIN EXTMICIN TXIN AUXTXIN SQIN PLIN MICIN GNDD LIMIN RSSI
FAST_OFF_IGN GATED_RX_AUDIO ADAPT RX_AUDIO FILTERED_AUDIO ASFIC_MIC_AUD_OUT
100
0.1uF
VAG 3 U202 2 0.22uF 1 C205
EXP_AUDIO RX_IN
H4
C212
NC
J5 H6 J6
U201
MIC
R201 R202
0.1uF
NC NC
A7 C7 D7 H7 J7
FLAT_TX_AUDIO
100K 10K C206 R203 0.1uF C207
DET_AUDIO
B8 E8 G8
0.22uF
MOD_IN AUDIO_PA_ENABLE EXTERNAL_ALARM B+_CONTROL HIGH_LOW_BAND
GND3
GND4
GND5
GND6
GND7
GND8
TX_IN
10K
GND9
G3
G5
G6
F3
F4
D2
D3
F5
D4
D5
E6
F6
E4
RSSI
9V3 C251 C203 39PF C204 39PF 0.1uF 14 4 U202 11 R215 R210 1K R209 10K R208 10K 13 12
C208 330pF
C231 .01uF
E5
B7
GNDA
GND1
GND2
39PF
C230 R236
FLAT_RX_AUDIO
4.7uF 100K
RSSI_BUF
0NU
Schematic Diagram for HLF9003A, HLF9004A, HLF9009A & HLF9010A Main Boards, Audio & Digital Controller Section
September, 2000
6880906Z19-O
FLT_A+ +5V FLT_A+ R460 IGNITION ONE SHOT 200K R463 1M 8 R465 6 5 R461 47K R462 200K R464 470K R449 33K R450 4.7K Standard/Data Ignition C460 2.2UF R468 10K R467 10K Q460 2 1 U460 3 1 2 +5V S401 SWITCH 63V 500mA C442 39PF VR441 33V FAST OFF CIRCUIT: IGN DETECTOR R442 47K R452 10K SW_B+
J400
B+_CONTROL
F401
Q461
L414
9 SWB+
IGNITION_CONTROL
4.7K R466 4.7K
U460 4
3 4 Q450 R451 4.7K VR451 5.1V L403 BLM21A05
FAST_OFF_IGN
10 IGNITION_SENSE
C451 39PF
IGNITION_SENSE VPP
R433 VR430 5.1V
+5V
FLT_A+ R421 L404 BLM21A05 C421 39PF

14 W W1 X0 X X1 Y0 Y Y1 Z0 Z Z1 CNTL VSS 9 13 5 4
SCI_TX
NC R431 4.7K
15 1 2 3
SCI_DATA_OUT
U402
16 VDD
560
PUBLIC_ADDRESS
10K
W0
VR421 14V
PTT GATED_RX_AUDIO FLAT_RX_AUDIO EXTERNAL_ALARM K9V1_ENABLE

+5V +5V R423 D403 4.7K R424 R440 4.7K
R422
L405 BLM21A05 VR422 14V
6 10 11 12
BUS+
4.7K C422 39PF
SCI_DATA_IN
7
FLT_A+
VEE
GROUND
C431 39PF R412 4.7K Q410 Q411 R411 10K C412 39PF VR412 33V C410 39PF VR410 5.1V NC
VR431 14V L406 BLM21A05 L413 BLM21A05 L407 BLM21A05 L415
DATA_PTT
560
12 4 15 16 1 2 14 3 5 11 13
PUBLIC_ADDRESS/SPEAKER_MUTE EXTERNAL_ALARM/TX_SENSE SYS_BUSY/RSSI_BUF EXT_SPKR+ INTERNAL EXT_SPKREXTERNAL_MIC_AUDIO HOOK PTT/DATA_PTT FLAT_TX_AUDIO EXT_RX_AUDIO INT_SPK+ SPEAKER JUMPER
+5V
R427 100K
C411 .01uF
L416
L408 R430 4.7K BLM21A05 L409
RSSI_BUF
C416 39PF R401 C401 FLT_A+ 0.1UF R402 1K C402 .0033uF C415 39PF C409 .1uF U401
VCC 7
BLM21A05 VR416 14V R435 560 C425 39PF VR415 14V VR425 5.1V L410 BLM21A05 L411 BLM21A05 L412 BLM21A05 L435 NC SW_B+ C418
RX_AUDIO
4.7K +5V D402
FLAT_TX_AUDIO
C405 .001uF C407 .01uF VR426 14V 4.7uF R417 100K C426 39PF
C423 39PF
+5V R406 22K R404 10K R405 R428 10K Q401 C404 47UF 10K C403 NU NC D401
2 9 1 3 8 INV NINV RR M_SS GND1
OUT1
C413
C414
FLT_A+
OUT2 GND2 6
FLT_A+ SW_B+ 9V3 +5V VAG
39pF R418
1000pF R426
SW_B+ 9V3
R419 100 C419
AUDIO_PA_ENABLE
200K
9V3 10K
+5V VAG
R420 100K C427 39PF
C406 .001uF
C408 .01uF
2 3 U403
8 1 4 VAG
R425 10K
6 5 U403
8 7 4
NC
47uF VR427 14V
INT_SPKRINT_SPKR+ MIC HOOK_RSS
Schematic Diagram for HLF9003, HLF9004A, HLF9009A & HLF9010A Main Board, Audio PA & I/O Sections 10
6880906Z19-O
September, 2000
1 NC 3 D621 R621 FLT_A+ 2.2K VR621 5.1V C621 39PF C622 47uF 2 USW_+5V_CL
U601 4 5 R606 9V3 0 C601 39PF C602 .1uF C603 10uF R601 10K 6 2 3 1 R602 7.5K C604 33uF C605 .1uF R631 10 D631 R632 R603 1.2K Q601 10 2 C631 .1uF C632 33uF 1 3
8 7 6 5
U631
IN FDBK 5V_TAP _ERORR OUT SENSE SHDN GND 1 2 3 4
+5V C633 .022uF C634 47uF C635 .1uF
R604 6.8K
R605 22K RESET
Q611 SW_B+ C613 39PF TP601 BATTERY_VOLTAGE R613 3.3K R617 ON_OFF_CONTROL 3.3K R642 16.2K C641 0.1uF VR641 5.1V R641 47.5K
R611 1.2K
R612 3.3K
B+_CONTROL
2 3 D611 1 1K 10K C611 47uF R616 10K C612 0.1uF R614 R615 Q612
IGNITION_CONTROL
Schematic Diagram for HLF9003A, HLF9004A, HLF9009A & HLF9010A Main Boards, Supply Voltage Section
September, 2000 6880906Z19-O
11
C374
9V3
0.01UF C360
EXP_AUDIO
B3 VCC C4 D1 E3 C2 C350 C1 C362 100NF 100NF D3 F5 E4 B5 B1 B4 E5 D6 E6 NFILOUT C6 F4 A2 F2 F3 A5 C3 E1 A4 D4 E2 C5 D5 D2 B6 B2 NC C358 0.33UF C365 0.1UF R355 1K 3300PF R357 100K C363 3300PF C364 NC 3.3UF C355 0.33UF C353 C361 0.1UF
HC_CNTL
ICENAB FFOUT U350 CPNENAB 35U50 EXPOUT FFENAB CBUFOUT HIENAB EXPIN CBUFIN RSSIIN FFIN NFILIN NC NC1 NC2 NC3 NC4 GND A3 COMPOUT LODSAB EXPBYP COMPCAP VAG FFCNTL CFBBYP CLIPREF NOISHLD COMPBYP HCIDSAB EXPADJ
RX_IN
TX_IN
0.1UF
FILTERED_AUDIO RSSI
NC C300 .220UF NC NC NC NC
DISC
C367 3300PF
C356 3.3UF
R356 10.0K
R354 100K C357
ASFIC_MIC_AUD_OUT
0.01UF
R353 1.5K
C354 R351 22K R350 100K 0.01UF C351 470PF C352 470PF R352 47.5K
Schematic Diagram for HLF9003, HLF9004A, HLF9009A & HLF9010A Main Board, Hear Clear Section 12
6880906Z19-O
September, 2000
Circuit Board Details for HLF9003A & HLF9004A Main Boards
September, 2000
6880906Z19-O
13
Parts List
HLF9003 & HLF9004 Radio, 900 MHz, 30 W REFERENCE SYMBOL MOTOROLA PART NO. PL-201021-O DESCRIPTION capacitor, xed: uF +/-15%; 50 V: unless otherwise stated 39 pF ceramic 0.1 0.01 tantalum 3.3 10%; 6 V ceramic 0.1 0.01 1000 pF 39 pF 0.01 0.01 ceramic 0.1 tantalum 1 10%; 16 V ceramic 0.1 39 pF 24 pF ceramic 0.1 ceramic 0.1 39 pF 470 pF 39 pF ceramic 0.22 ceramic 0.1 ceramic 0.22 330 pF tantalum 10 20%; 16 V .022 10% 0.1 10% ceramic 0.1 ceramic 0.1 tantalum 1 10%; 16 V 33 nF tantalum 4.7 10%; 16 V 0.01 ceramic 0.1 tantalum 47 20%; 10 V tantalum 0.1 10%; 35 V 0.01 tantalum 4.7 10%; 16 V 0.01 10 33 pF ceramic 0.1 .033 39 pF ceramic 0.1 tantalum 10 10%; 7 V tantalum 1 10%; 16 V ceramic 0.1 0.220 100 nF 470 pF 0.33 0.01 tantalum 3.3 10%; 6 V 0.01 0.33 ceramic 0.1 100 nF 3300 pF ceramic 0.1 3300 pF 0.01 ceramic 0.1 3.3 nF tantalum 47 20%; 10 V 1000 pF 0.01 ceramic 0.1; low DIST 39 pF 0.01 39 pF 1000 pF 39 pF tantalum 4.7 10%; 16 V 47 39 pF 39 pF 39 pF 39 pF 39 pF tantalum 2.2 10%; 20 V HLF9003 & HLF9004 Radio, 900 MHz, 30 W REFERENCE SYMBOL C601 C602 C603 C604 C605 C611 C612 C613 C621 C622 C631 C632 C633 C634 C635 C641 C642 thru 652 C701 thru 703 C711, 712 C713 C722, 723 C724 C725, 726 C727 C731 C741 C5200 C5201 C5202 C5203, 5204 C5205 C5208 C5211 C5212 C5213 C5214 C5223 C5224 C5225 C5226 C5227 C5228 C5229 C5231 C5233 C5234 C5235 thru 5237 C5239 C5251 C5252 C5308 C5310 C5311 C5312 C5321, 5322 C5323 thru 5326 C5404 C5700 C5701, 5702 C5703 C5704 C5705 thru 5708 C5709 thru 5711 C5712, 5713 C5714 thru 5717 C5718 C5719 C5720 thru 5731 C5732 thru 5735 C5737 thru 5743 C5744 thru 5747 C5748 C5750 C5751 C5752 thru 5776 C5778, 5779 C5782 C5783 C5784, 5785 C5786 C5787, 5788 C5789 C5790 MOTOROLA PART NO. 2113740F41 2109720D14 2380090M24 2311049J40 2109720D14 2311049C05 2113743K15 2113740F41 2113740F41 2311049J44 2109720D14 2311049J40 2113743E07 2311049J44 2109720D14 2113743K15 2113740F41 2113740F41 2113743K15 2113740F41 2113740F41 2113743K15 2113740F41 2113743K15 2113743K15 2113740F41 2113740F35 2113740F14 2113740F31 2113743K15 2113740F34 2113743K15 2113740F32 2113740F30 2113740F40 2113740F17 2113743K15 2113741F29 2311049A11 2113743K05 2311049J11 2113743K15 2113740F41 2311049A05 2113740F41 2113743K15 2113740F41 2113740F41 2311049A57 2113743K15 2113740F23 2113740F41 2113741F49 2113740F14 2113740F41 2113741F49 2113740F37 2113743E07 2113743K15 2113740F08 2113740F09 2113740F41 2113740F51 2311049J26 2311049J11 2311049A14 2311049J11 2113743K15 2113743E07 2113743E07 2109720D01 2113741F49 2105248W02 2113741A57 2113740F41 2113740F41 2113740F15 2113740F05 2113740F11 2113740F12 2113740F51 2113740F12 2113740F13 PL-201021-O DESCRIPTION 39 pF ceramic 0.1; low DIST 10 20%; 50 V SMT tantalum 33 20%; 16 V ceramic 0.1; low DIST tantalum 47 10%; 16 V ceramic 0.1 39 pF 39 pF tantalum 47 20%; 10 V ceramic 0.1; low DIST tantalum 33 20%; 16 V 22 nF tantalum 47 20%; 10 V ceramic 0.1; low DIST ceramic 0.1 39 pF 39 pF ceramic 0.1 39 pF 39 pF ceramic 0.1 39 pF ceramic 0.1 ceramic 0.1 39 pF 22 pF 3 pF 15 pF ceramic 0.1 20 pF ceramic 0.1 16 pF 13 pF 36 pF 3.9 pF ceramic 0.1 1500 pF tantalum 3.3 10%; 16 V ceramic .039 tantalum 4.7 10%; 16 V ceramic 0.1 39 pF tantalum 0.47 10%; 25 V 39 pF ceramic 0.1 39 pF 39 pF 10 ceramic 0.1 6.8 pF 39 pF 0.01 3 pF 39 pF 0.01 27 pF ceramic .022 ceramic 0.1 1.6 pF 1.8 pF 39 pF 100 pF tantalum 10 20%; 16 V tantalum 4.7 10%; 16 V tantalum 4.7 10%; 20 V tantalum 4.7 10%; 16 V ceramic 0.1 ceramic 22 nF ceramic 22 nF ceramic 10 nF; low DIST 0.01 1.2 nF 33 nF 39 pF 39 pF 3.3 pF 1.2 pF 2.2 pF 2.4 pF 100 pF side, entry 2.4 pF 2.7 pF HLF9003 & HLF9004 Radio, 900 MHz, 30 W REFERENCE SYMBOL C5791 C5792, 5793 C5794 C5795 C5796 thru 5799 C5802, 5803 C5804 thru 5806 C5810, 5811 C5813, 5814 C6501 C6502 C6503 C6505, 6506 C6507 C6508 thru 6510 C6511 thru 6513 C6514 thru 6516 C6517 thru 5719 C6520 C6522 C6523 C6524 C6525 C6526 C6529 C6532 thru 6535 C6537 C6538 C6539 C6540 C6541, 6542 C6545 C6546 C6548 C6549, 6550 C6551 C6552, 6553 C6554 C6555 C6563 C6564 C6565, 6566 C6567, 6568 C6569 C6570, 6571 CR150, 151 CR721 CR5700 CR5701, 5702 CR6501 CR6502, 6503 CR6508 CR6509 D101, 102 D200 D401, 402 D403 D611 D621 D631 D5201 D5303 F401 FL5201 FL5202 FL5203, 5204 H6501 H6502 J100 J400 J6500 J6501 J6502 L131, 132 MOTOROLA PART NO. 2113740F03 2113740F11 2113740F41 2113740F51 2109720D14 2109720D14 2113743K15 2113740F41 2113740F41 2113743K15 2113740F05 2113740F41 2113740F41 2113743K15 2113741F49 2311049A01 2311049A08 2113740F41 2113740F11 2113740F41 2113740F24 2113743E07 2113741F25 2113740F41 2113740F41 2113740F41 2113740F41 2113741F49 2113742B22 2113742B23 2113742B22 2113741F49 2311049A01 2113741F49 2113743K15 2113741F49 2311049A08 2113740B39 2111078B45 2111078A15 2113741F25 2311049A01 2113742B23 2113743K15 2113740F41 4813833C02 4813833C02 4802233J09 4862824C01 4813833C02 4802482J02 4813832B35 4805218N57 4813833C02 4813833C02 4880939T01 4813833C02 4813833C02 4813833C02 4813833C02 4880154K03 4880154K03 6585711L05 9185747L01 9180098D14 9102603S25 0108704H03 5185807L01 0902636Y01 2804503J01 3080562V01 0905901V06 3080562V01 2462587Q40 PL-201021-O DESCRIPTION 1 pF 2.2 pF 39 pF 100 pF ceramic 0.1; low DIST ceramic 0.1; low DIST ceramic 0.1 39 pF 39 pF ceramic 0.1 1.2 pF 39 pF 39 pF ceramic 0.1 0.01 tantalum 0.1 10%; 35 V tantalum 1 10%; 35 V 39 pF 2.2 pF 39 pF 7.5 pF ceramic .022 1000 pF 39 pF 39 pF 39 pF 39 pF .01 10 pF 12 pF 10 pF .01 tantalum 0.1 10%; 35 V .01 ceramic 0.1 .01 1 39 pF 130 pF 2.7 pF 1000 pF tantalum 0.1 10%; 35 V 12 pF ceramic 0.1 39 pF diode: (see note 1) dual 70 V common cathode dual 70 V common cathode triple SOT 143-RH varactor dual 70 V common cathode pin diode SMD transient suppressor SMT dual Schottky common cathode dual 70 V common cathode dual 70 V common cathode silicon SMT dual 70 V common cathode dual 70 V common cathode dual 70 V common cathode dual 70 V common cathode dual Schottky dual Schottky fuse: 63 V, 500 mA SMT lter: 455 kHz ceramic lter 455 kHz ceramic lter 938 MHz ceramic lter hybrid: matching hybrid harmonic lter hybrid connector, receptacle: exible cable, side entry accessory 16-pin power cable antenna power cable coil, rf: inductor 270 nH 10% R100 R101 thru 103 R104 R105 R106 R107 R108 R109, 110 R111, 112 R113 R114 R115, 116 R121 R122 R123 R126 R127 0662057A65 0662057B05 0662057A89 0662057A65 0662057A73 0662057A57 0662057A73 0662057A35 0662057A65 0662057A85 0662057A93 0662057A73 0662057A65 0662057A89 0662057A73 0662057A73 0662057A65 HLF9003 & HLF9004 Radio, 900 MHz, 30 W REFERENCE SYMBOL L200 L403 thru 413 L414 thru 416 L418 L419 L420 thru 428 L429, 430 L431 thru 434 L435 L5201 L5203 L5211 L5302 L5321 L5322 L5401, 5402 L5700 thru 5704 L5705, 5706 L5707 L5708 L5709 L6501 L6502 L6503 L6504 thru 6506 L6507 L6508 L6509 L6510 L6511 L6512 L6513 L6514 thru 6517 L6518, 6519 L6521 L6522, 6523 Q101 thru 103 Q141 Q150 Q200 Q401 Q410, 411 Q415 Q450 Q460, 461 Q601 Q611 Q612 Q731 Q741 Q742 Q5201 Q5230 Q5301 Q5700 Q5701 Q5702 thru 5704 Q5705 Q5706, 5707 Q6501 Q6505 Q6506 MOTOROLA PART NO. 2462587P30 2402601S05 2484657R01 2402601S05 2484657R01 2402601S05 2484657R01 2402601S05 2484657R01 2462587M19 2462587T30 2483411T74 2413926E09 2460591A01 2462587T12 2483411T69 2462587T30 2462587T17 2462587T30 2462587T17 2462587Q44 2462587T13 2460591A11 2462587T13 2484657R01 2484562T01 2484657R01 2460591R53 2484657R01 2462587T13 2460591E24 2460591A01 2462587T13 2484657R01 2409348J03 2460591R53 4880048M01 4880048M01 4882033T01 4880214G02 4880214G02 4880048M01 4880494U01 4880048M01 4880048M01 4880214G02 4805128M27 4880214G02 4880214G02 4880048M01 4805128M27 4813827A07 4813824A17 4813827A18 4880048M01 4813824A17 4809527E01 4804188K01 4809527E01 4813827A26 4880225C20 4813824B01 PL-201021-O DESCRIPTION inductor 33 uH 10% inductor BLM21A05 ferrite bead inductor BLM21A05 ferrite bead inductor BLM21A05 ferrite bead inductor BLM21A05 ferrite bead 5% inductor 1200 nH 5%, low PRO inductor 1.0 uH inductor 1.2 mH inductor 6.8 nH 5% inductor 4.2 nH inductor 56 nH 5%, low PRO inductor 0.47 mH inductor 1.0 uH 5%, low PRO inductor 150 nH 5%, low PRO inductor 1.0 uH 5%, low PRO inductor 150 nH 5%, low PRO inductor 560 nH 10% inductor 68 nH 5%, low PRO inductor 7.66 nH air wound inductor 68 nH 5%, low PRO ferrite bead inductor 2.5 nH ferrite bead inductor 82 nH ferrite bead inductor 68 nH 5%, low PRO inductor 23.75 nH air wound inductor 4.2 nH inductor 68 nH 5%, low PRO ferrite bead inductor 3.85 nH inductor 82 nH air wound transistor: (see note 1) NPN DTC144EK NPN DTC144EK NPN DTC114YK NPN MMBT3904 NPN MMBT3904 NPN DTC144EK PNP DTA144EKA NPN DTC144EK NPN DTC144EK NPN MMBT3904 PNP BSR33 NPN MMBT3904 NPN MMBT3904 NPN DTC144EK PNP BSR33 NPN MMBR941T1 PNP 3906L NPN MRF9411LT1 NPN DTC144EK PNP 3906L NPN RF NE85663 NPN RF NE85634 NPN RF NE85663 NPN RF MRF8372 NPN RF MRF847 NPN 2222AT1 resistor, xed: +/-5%; 1/8 W: unless otherwise stated 4.7k 200k 47k 4.7k 10k 2.2k 10k 270 ohm 4.7k 33k 68k 10k 4.7k 47k 10k 10k 4.7k HLF9003 & HLF9004 Radio, 900 MHz, 30 W REFERENCE SYMBOL R131 R132 R133 R135, 136 R142 R145 R146, 147 R150 R151 R152 R153 R155 R200 R201 R202, 203 R204 R205 R206 R208, 209 R210 R221 R222 R223 R232 R233 R236 R237, 238 R251, 252 R350 R351 R352 R353 R354 R355 R356 R357 R401 R402 R404, 405 R406 R411 R412 R417 R418 R419 R420 R421 R422, 423 R424 R425, 426 R427 R428 R430 R431 R433 R435 R440 R442 R449 R450, 451 R452 R460 R461 R462 R463 R464 R465, 466 R467, 468 R601 R602 R603 R604 R605 R606 R611 R612, 613 R614 R615, 616 R617 R621 R631, 632 R641 R642 MOTOROLA PART NO. 0662057A65 0662057A81 0662057A97 0662057A73 0662057A73 0662057A73 0662057A35 0662057A89 0662057B05 0662057A56 0662057A85 0662057A89 0662057A73 0662057A97 0662057A73 0662057A25 0662057A49 0662057A41 0662057A73 0662057A49 0662057B47 0662057A89 0662057R92 0662057A93 0662057A73 0662057A97 0662057A93 0662057R92 0662057G13 0662057A81 0662057R92 0662057A53 0662057G13 0662057R30 0662057R60 0662057A97 0662057A65 0662057A49 0662057A73 0662057A81 0662057A73 0662057A65 0662057A97 0662057B05 0662057A25 0662057A97 0662057A43 0662057A65 0662057A43 0662057A73 0662057A97 0662057A73 0662057A65 0662057A73 0662057A65 0662057A43 0662057A65 0662057A89 0662057A85 0662057A65 0662057A73 0662057B05 0662057A89 0662057B05 0662057B22 0662057B14 0662057A65 0662057A73 0662057A73 0662057R55 0662057R31 0662057A69 0662057A81 0662057B47 0662057A51 0662057C87 0662057A49 0662057A73 0662057C87 0662057A57 0662057A01 0662057R92 0662057R67 PL-201021-O DESCRIPTION 4.7k 22k 100k 10k 10k 10k 270 47k 200k 2k 33k 47k 10k 100k 10k 100 ohm 1k 470 ohm 10k 1k 0 ohm 47k 47.5k 1%; 1/10 W 68k 10k 100k 68k 47.5k 1%; 1/10 W 100k 22k 47.5k 1.5k 100k 1k 10.0k 100k 4.7k 1k 10k 22k 10k 4.7k 100k 200k 100 ohm 100k 560 ohm 4.7k 560 ohm 10k 100k 10k 4.7k 10k 4.7k 560 ohm 4.7k 47k 33k 4.7k 10k 200k 47k 200k 1M 470k 4.7k 10k 10k 7.50k 1%; 1/10 W 1.21k 6.8k 22k 0 ohm 1.2k 3.3k 1k 10k 3.3k 2.2k 10 ohm 47.5k 16.2k HLF9003 & HLF9004 Radio, 900 MHz, 30 W REFERENCE SYMBOL R702 R703, 704 R705 R706 R711 R712 R713 R714 R715 R716 thru 718 R719 R720 R721 R722 R723 R724 R725, 726 R727 R728 thru 731 R732 thru 734 R736, 737 R740 R741, 742 R743 R5201 R5202 R5203 R5204 R5205 R5207 R5211 R5212 R5221 R5223 R5224 R5230 R5240 R5241 R5302 R5306 R5311, 5312 R5321 R5322 R5323 R5324, 5325 R5327 R5401 R5700 R5703 R5704 R5705 R5706 R5707 R5708, 5709 R5710 R5711 thru 5713 R5714 R5715 R5716 R5717 R5718 R5724 thru 5727 R5728 R5729 R5731 thru 5733 R5734 thru 5736 R5737, 5708 R5739, 5740 R5741 R5742 R5743 R5744, 5745 R5746 R5747 R5748 R5750, 5751 R5752 R5753 R5754 R5755 R5756, 5757 R6503 R6504 MOTOROLA PART NO. 0662057A58 0662057A81 0662057A43 0662057A97 0662057A81 0662057B47 0662057A42 0662057A25 0662057R30 0662057R60 0662057R30 0662057R60 0662057A67 0662057A81 0662057A97 0662057A61 0662057A73 0662057A81 0662057G13 0662057A65 0662057A65 0662057A57 0662057A53 0662057A49 0662057A76 0662057A85 0662057A69 0662057A25 0662057A56 0662057B47 0662057A47 0662057A67 0662057B01 0662057A70 0662057A76 0662057A89 0683962T49 0662057B47 0662057A33 0662057A29 0662057A76 0662057A33 0662057A01 0662057A36 0662057A39 0662057B47 0662057A18 0662057A57 0662057A73 0662057A37 0662057A73 0662057A42 0662057A61 0662057B05 0662057A73 0662057A65 0662057A59 0662057A57 0662057A58 0662057A59 0662057A53 0662057A42 0662057A37 0662057A29 0662057A25 0662057A18 0662057A09 0662057A18 0662057A01 0662057A69 0662057A73 0662057A31 0662057A73 0662057A69 0662057A09 0662057A59 0662057A37 0662057A13 0662057A37 0662057A09 0662057A35 0662057A01 0662057C69 PL-201021-O DESCRIPTION 2.4k 22k 560 ohm 100k 22k 0 ohm 510 ohm 100 ohm 1k 1%; 1/10 W 10.0k 1%; 1/10 W 1k 1%; 1/10 W 10.0k 1%; 1/10 W 5.6k 22k 100k 3.3k 10k 22k 100k 1% 4.7k 4.7k 2.2k 1.5k 1k 13k 33k 6.8k 100 2k 0 ohm 820 ohm 5.6k 130k 7.5k 13k 47k 100 ohm 0 ohm 220 ohm 150 ohm 13k 220 ohm 10 ohm 300 ohm 390 ohm 0 ohm 51 ohm 2.2k 10k 330 ohm 10k 510 ohm 3.3k 200k 10k 4.7k 2.7k 2.2k 2.4k 2.7k 1.5k 510 ohm 330 ohm 150 ohm 100 ohm 51 ohm 22 ohm 51 ohm 10 ohm 6.8k 10k 180 ohm 10k 6.8k 22 ohm 2.7k 330 ohm 33 ohm 330 ohm 22 ohm 270 ohm 10 ohm 560 ohm HLF9003 & HLF9004 Radio, 900 MHz, 30 W REFERENCE SYMBOL R6505 R6506 R6508 R6509 R6514 R6515 R6519 R6520 R6523 thru 6525 R6526 R6527, 6528 R6530 R6531 R6532 R6540 R6555 S401 E5700 E5701 E5702, 5703 E5704 SH5201 SH5202, 5203 SH6501 U101 U102 U103 U104 U105 U106 U201 U202 U203 U204 U251 U350 U401 U402 U403 U460 U601 U631 U701 U702 U5201 U5211 U5700 U5701 U5702 U5703 U5704, 5705 U5706, 5707 U6501 U6502 VR101 VR410 VR412 VR415, 416 VR421, 422 VR425 VR426, 427 VR430 VR431 VR441 VR451 VR621 VR641 VR650 Y5201 Y5202 MOTOROLA PART NO. 0662057C27 0662057C69 0683962T17 0662057G13 0662057G13 0662057A61 0680361L01 1705603W01 0662057A53 0662057A01 0662057A43 0662057A15 0662057A09 0662057G13 0680195M25 0662057A33 4085797L01 2602660J02 2604668E02 2602660J02 2680524L01 2605261V01 2605417V01 2680567V01 5180421V01 5108444S61 5185963A21 5108444S49 5113805A30 5113808A07 5105835U45 5113819A04 5109522E13 5109781E79 5113818A03 5105835U50 5109699X01 5180173M02 5113818A10 5113818A03 5105625U25 5105469E65 5113819A02 5113811G02 5180207R01 5185670L01 5105279V31 5105109Z59 5105457W46 5113816A07 4805921T02 4804122K04 5113829D23 4805921T02 4813830A23 4813830A14 4813830A40 4813830A27 4813830A27 4813830A14 4813830A27 4813830A14 4813830A27 4813830A40 4813830A14 4813830A14 4813830A14 14813830A25 9102651Y01 9102651Y02 PL-201021-O DESCRIPTION 10 ohm 560 ohm 4.7 ohm 100k 100k 3.3k therm 47k shunt, 1.639 mH 1.5k 10 560 39 22 100k 100 220 switch: 2-position shield: MMIC shield VCO shield buffer shield synthesizer shield LNA shield mixer shield RF power module shield integrated circuit: (see note 1) MC68HC11K1 FLASH memory SRAM EEPROM 1 of 8 DCD/demux 74HC138 AND quad 2 INP MC74AC08D ASFIC quad op-amp switch SPDT switch SDT dual op-amp hear clear IC audio PA switch SPDT dual op-amp dual op-amp 9.3 V regulator LM2941 voltage regulator LP2951AC quad op-amp D/A converter 6-bit 4-ch. with SPI IFIC mixer DBL balanced 16.8 MHz ref. oscillator mode MMIC frac-N syntheizer regulator 5 V 500 mA MC78M05BDT switch FMC2 microstrip line resonator 890-950 MHz, 18 W, 12.5 V switch FMC2 Zener diode: (see note 1) 10 V 5%; 225 mW MMBZ5240BL 5.1 V 5%; 225 mW MMBZ5231B 33 V 5%; 225 mW MMBZ5257B 14 V 5%; 225 mW MMBZ5244L 14 V 5%; 225 mW MMBZ5244L 5.1 V 5%; 225 mW MMBZ5231B 14 V 5%; 225 mW MMBZ5244B 5.1 V 5%; 225 mW MMBZ5231B 14 V 5%; 225 mW MMBZ5244L 33 V 5%; 225 MMBZ5257B 5.1 V 5%; 225 mW MMBZ5231B 5.1 V 5%; 225 mW MMBZ5231B 5.1 V 5%; 225 mW MMBZ5231B 12 V 5%; 225 mW MMBZ5242B crystal: (see note 2) lter 45.1 MHz lter 45.1 MHz HLF9003 & HLF9004 Radio, 900 MHz, 30 W REFERENCE SYMBOL MOTOROLA PART NO. PL-201021-O DESCRIPTION Y5211 4802653Y01 resonator 44.6450 MHz notes: 1. For optimum performance, diodes, transistors and integrated circuits must be ordered by MOTOROLA part numbers. 2. When ordering quartz crystal units or ceramic resonators, specify carrier frequency, crystal (or resonator) frequency, and crystal (or resonator) type number.
Parts List for HLF9003A & HLF9004A Main Boards 14

6880906Z19-O September, 2000
C100 C101 thru 103 C104 C105 C106 C107 C108 C109, 110 C111 C113, 114 C131 C132 C133 thru 135 C136, 137 C146 C151 C200 C201 C202 C203, 204 C205 C206 C207 C208 C209 C210 C211 C212 C221 C222 C223 C224 C225 C226 C227 C228 C229 C230 C231 C232 C233 C234 C237 C241 thru 243 C251 C252 C253 C254 C300 C350 C351, 352 C353 C354 C355, 356 C357 C358 C360, 361 C362 C363, 364 C365 C367 C374 C401 C402 C404 C405, 406 C407, 408 C409 C410 C411 C412, 413 C414 C415, 416 C418 C419 C421 thru 423 C425 thru 427 C431 C442 C451 C460
2113740F41 2113743K15 2113741F49 2311049A42 2113743K15 2113741F49 2113741F25 2113740F41 2113741F49 2113741F49 2113743K15 2311049A07 2113743K15 2113740F41 2113740F36 2113743K15 2113743K15 2113740F41 2113741F17 2113740F41 2113743F08 2113743K15 2113743F08 2113741F13 2311049J26 2113741A53 2113743A19 2113743K15 2113743K15 2311049A07 2113741A57 2311049J11 2113741F49 2113743K15 2311049J44 2311049A01 2113741F49 2311049J11 2113741F49 2311049J26 2113740F39 2113743K15 2113741A57 2113740F41 2113743K15 2311049J23 2311049A07 2113743K15 2113743A23 2113743A19 2113741F17 2311049A04 2113741F49 2311049A42 2113741F49 2311049A04 2113743K15 2113743A19 2113741A33 2113743K15 2113741A33 2113741F49 2113743K15 2113741F37 2311049J44 2113741F25 2113741F49 2109720D14 2113740F41 2113741F49 2113740F41 2113741F25 2113740F41 2311049J11 2311049J44 2113740F41 2113740F41 2113740F41 2113740F41 2113740F41 2311049A09
Circuit Board Details for HLF9009A & HLF9010A Main Boards

September, 2000 6880906Z19-O
15
Parts List
HLF9009A & HLF9010A Radio, 900 MHz, 12 W REFERENCE SYMBOL MOTOROLA PART NO. PL-201022-O DESCRIPTION capacitor, xed: uF +/-15%; 50 V: unless otherwise stated 39 pF ceramic 0.1 0.01 tantalum 3.3 10%; 6 V ceramic 0.1 0.01 1000 pF 39 pF 0.01 0.01 0.1 tantalum 1 10%; 16 V ceramic 0.1 39 pF 24 pF ceramic 0.1 0.1 39 pF 470 pF 39 pF ceramic 0.22 ceramic 0.1 ceramic 0.22 330 pF tantalum 10 20%; 16 V .022 10% 0.1 10% ceramic 0.1 tantalum 1 10%; 16 V 33 nF tantalum 4.7 20%; 10 V 0.01 ceramic 0.1 tantalum 47 20%; 10V tantalum 0.1 10%; 35 V 0.01 tantalum 4.7 10%; 16 V 0.01 10 33 pF ceramic 0.1 .033 39 pF ceramic 0.1 tantalum 10 10%; 7 V tantalum 1 10%; 16 V ceramic 0.1 0.220 100 nF 470 pF 0.33 0.01 3.3 0.01 0.33 ceramic 0.1 100 nF 10% 3300 pF ceramic 0.1 3300 pF 0.01 ceramic 0.1 3.3 nF tantalum 47 20%; 10 V 1000 pF 0.01 ceramic 0.1; low DIST 39 pF 0.01 39 pF 1000 pF 39 pF tantalum 4.7 10%; 16 V tantalum 47 20%; 10 V 39 pF 39 pF 39 pF 39 pF 39 pF tantalum 2.2 10%; 20 V 39 pF HLF9009A & HLF9010A Radio, 900 MHz, 12 W REFERENCE SYMBOL C602 C603 C604 C605 C611 C612 C613 C621 C622 C631 C632 C633 C634 C635 C641 C642 thru 652 C701 thru 703 C711 C712 C713, 714 C722, 723 C724 C725, 726 C727 C731 C741 C5200 C5201 C5202 C5203, 5204 C5205 C5208 C5211 C5212 C5213 C5214 C5223 C5224 C5225 C5226 C5227 C5228 C5229 C5231 C5233 C5234 C5235 thru 5237 C5239 C5251 C5252 C5308 C5310 C5311 C5312 C5321, 5322 C5323 thru 5326 C5404 C5700 C5701, 5702 C5703 C5704 C5705 thru 5708 C5709 thru 5711 C5712, 5713 C5714 thru 5717 C5718 thru 5731 C5732 thru 5735 C5737 thru 5743 C5744 thru 5747 C5748 C5750 C5751 C5752 thru 5779 C5782 C5783 C5784, 5885 C5786 C5787, 5788 C5789 C5790 C5791 C5792, 5793 C5794 MOTOROLA PART NO. 2109720D14 2380090M24 2311049J40 2109720D14 2311049C05 2113743K15 2113740F41 2113740F41 2311049J44 2109720D14 2311049J40 2113743E07 2311049J44 2109720D14 2113743K15 2113740F41 2113740F41 2113743E07 2113743K15 2113740F41 2113740F41 2113743K15 2113740F41 2113743K15 2113743K15 2113740F41 2113740F35 2113740F14 2113740F31 2113743K15 2113740F34 2113743K15 2113740F32 2113740F30 2113740F40 2113740F17 2113743K15 2113741F29 2311049A11 2113743K05 2311049J11 2113743K15 2113740F41 2311049A05 2113740F41 2113743K15 2113740F41 2113740F41 2311049A57 2113743K15 2113740F23 2113740F41 2113741F49 2113740F14 2113740F41 2113741F49 2113740F37 2113743E07 2113743K15 2113740F08 2113740F09 2113740F41 2113740F51 2311049J26 2311049J11 2311049A14 2113743E07 2113743E07 2109720D01 2113741F49 2105248W02 2113741A57 2113740F41 2113740F15 2113740F05 2113740F11 2113740F12 2113740F51 2113740F12 2113740F13 2113740F03 2113740F11 2113740F41 PL-201022-O DESCRIPTION ceramic 0.1; low DIST 10 20%; 50 V SMT tantalum 33 20%; 16 V ceramic 0.1; low DIST tantalum 47 10%; 16 V ceramic 0.1 39 pF 39 pF tantalum 47 10%; 16 V ceramic 0.1 tantalum 33 20%; 16 V 22 nF tantalum 47 20%; 16 V ceramic 0.1 ceramic 0.1 39 pF 39 pF 22 nF ceramic 0.1 39 pF 39 pF ceramic 0.1 39 pF ceramic 0.1 ceramic 0.1 39 pF 22 pF 3 pF 15 pF ceramic 0.1 20 pF ceramic 0.1 16 pF 13 pF 36 pF 3.9 pF ceramic 0.1 1500 pF tantalum 3.3 10%; 16 V .039 tantalum 4.7 10%; 16 V ceramic 0.1 39 pF tantalum 0.47 10%; 25 V 39 pF ceramic 0.1 39 pF 39 pF 10 ceramic 0.1 6.8 pF 39 pF 0.01 3 pF 39 pF 0.01 27 pF ceramic .022 ceramic 0.1 1.6 pF 1.8 pF 39 pF 100 pF tantalum 10 20%; 16 V tantalum 4.7 10%; 16 V tantalum 4.7 10%; 20 V ceramic 22 nF ceramic 22 nF ceramic 10 nF; low DIST 0.01 1.2 nF 33 nF 39 pF 3.3 pF 1.2 pF 2.2 pF 2.4 pF 100 pF 2.4 pF 2.7 pF 1 pF 2.2 pF 39 pF HLF9009A & HLF9010A Radio, 900 MHz, 12 W REFERENCE SYMBOL C5795 C5796 thru 5799 C5802, 5803 C5804 thru 5806 C5810, 5811 C5813, 5814 C6501 C6502 C6503 C6505, 6506 C6507 C6508 thru 6510 C6511 thru 6513 C6514 thru 6516 C6517 thru 6519 C6520 C6523 C6524 C6525 C6526 C6527 C6529 C6532 thru 6538 C6540 C6541, 6542 C6543 C6544 C6545 C6546 C6549, 6550 C6551, 6552 C6553 C6560 C6562 MOTOROLA PART NO. 2113740F51 2109720D14 2109720D14 2113743K15 2113740F41 2113740F41 2113743K15 2113740F21 2113740F41 2113740F41 2113743K15 2113741F49 2311049A01 2311049A08 2113740F41 2113740F27 2113740F31 2113743E07 2113741F25 2113740F27 2113740F41 2113740F41 2113740F41 2111078A19 2111078A09 2113742B29 2113743K15 2113740F41 2113743K15 2113743K15 2111078A06 2111078A17 2113740F15 2113740F38 PL-201022-O DESCRIPTION 100 pF ceramic 0.1; low DIST ceramic 0.1; low DIST 0.1 39 pF 39 pF ceramic 0.1 5.6 pF 39 pF 39 pF ceramic 0.1 0.01 tantalum 0.1 10%; 35 V tantalum 1 10%; 35 V 39 pF 10 pF 15 pF ceramic 22 nF 1000 pF 10 pF 39 pF 39 pF 39 pF 3.9 pF 1.8 pF 39 pF ceramic 0.1 39 pF ceramic 0.1 ceramic 0.1 1.5 pF 3.3 pF 3.3 pF 30 pF diode: (see note 1) dual 70 V common cathode dual 70 V common cathode triple SOT 143-RH varactor dual 70 V common cathode pin diode SMD dual dual transient suppressor SMT dual dual 70 V common cathode dual 70 V common cathode silicon SMT dual 70 V common cathode dual 70 V common cathode dual 70 V common cathode dual 70 V common cathode dual Schottky dual Schottky fuse: 6.3 V, 500 mA SMT lter: 455 kHz ceramic lter 455 kHz ceramic lter 938 MHz ceramic lter connector, receptacle: exible cable, side entry accessory 16-pin antenna connector power coil, rf: inductor, 270 nH inductor, 33 uH 10% inductor BLM21A05 ferrite bead inductor BLM21A05 ferrite bead inductor BLM21A05 ferrite bead inductor BLM21A05 ferrite bead 5% inductor, 1200 nH 5%, low PRO inductor, 1.0 uH 5%, low PRO HLF9009A & HLF9010A Radio, 900 MHz, 12 W REFERENCE SYMBOL L5211 L5302 L5321 L5322 L5401, 5402 L5700 thru 5704 L5705, 5706 L5707 L5708 L5709 L6501 L6502 L6503 L6504 thru 6506 L6507 L6508 L6509 L6511 L6513 L6514 thru 6517 L6518 L6519 L6520 MOTOROLA PART NO. 2483411T74 2413926E09 2460591A01 2462587T12 2483411T69 2462587T30 2462587T17 2462587T30 2462587T17 2462587Q44 2462587T13 2460591A11 2462587T13 2484657R01 2460591R53 2460591E24 2462587T13 2462587T13 2460591A11 2462587T13 2460591A11 2484657R01 2460591R53 PL-201022-O DESCRIPTION inductor, 1.2 mH 5%, low PRO inductor, 6.8 nH 5%, low PRO inductor, 4.2 nH 5%, low PRO inductor, 56 nH 5%, low PRO inductor, 0.47 mH 5%, low PRO inductor, 1.0 uH 5%, low PRO inductor, 150 nH 5%, low PRO inductor, 1.0 uH 5%, low PRO inductor, 150 nH 5%, low PRO inductor, 560 nH 10% inductor, 68 nH 5%, low PRO inductor, 7.66 nH air wound inductor, 68 nH, 5%, low PRO ferrite bead inductor, 82 nH inductor, 23.75 nH air wound inductor, 68 nH 5%, low PRO inductor, 68 nH 5%, low PRO inductor, 7.66 nH air wound inductor, 68 nH 5%, low PRO inductor, 7.66 nH air wound ferrite bead inductor, 82 nH transistor: (see note 1) NPN DTC144EK NPN DTC144EKA NPN DTC114YK NPN MMBT3904 NPN MMBT3904 NPN DTC144EKA NPN RXT_A28_T200 PNP DTA144EKA NPN DTC144EKA NPN DTC144EK NPN MMBT3904 PNP BSR33 NPN MMBT3904 NPN MMBT3904 NPN DTC144EK PNP BSR33 NPN MMBR941LT1 PNP 3906L NPN MRF9411LT1 NPN DTC144EK PNP 3906L NPN RF NE85633-T2B_R25 NPN RF NE85634 NPN RF NE85633-T2B_R25 NPN RF MRF8372 NPN 2222AT resistor, xed: +/-5%; 1/8 W: unless otherwise stated 4.7k 200k 47k 4.7k 10k 2.2k 10k 270 4.7k 33k 68k 10k 4.7k 47k 10k 10k 4.7k 4.7k 22k 100k 10k 10k 10k 270 47k 200k 2k 33k 47k HLF9009A & HLF9010A Radio, 900 MHz, 12 W REFERENCE SYMBOL R200 R201 R202, 203 R204 R205 R206 R208, 209 R210 R221 R222 R223 R232 R233 R236 R237, 238 R251, 252 R350 R351 R352 R353 R354 R355 R356 R357 R401 R402 R404, 405 R406 R411 R412 R417 R418 R419 R420 R421 R422, 423 R424 R425, 426 R427 R428 R430 R431 R433 R435 R440 R442 R449 R450, 451 R452 R460 R461 R462 R463 R464 R465, 466 R467, 468 R601 R602 R603 R604 R605 R606 R611 R612, 613 R614 R615, 616 R617 R621 R631, 632 R641 R642 R702 thru 704 R705 R706 R711 R712 R713 R714 R715 R716, 717 R718 R719 R720 MOTOROLA PART NO. 0662057A73 0662057A97 0662057A73 0662057A25 0662057A49 0662057A41 0662057A73 0662057A49 0662057B47 0662057A89 0662057R92 0662057A93 0662057A73 0662057A97 0662057A93 0662057R92 0662057G13 0662057A81 0662057R92 0662057A53 0662057G13 0662057R30 0662057R60 0662057A97 0662057A65 0662057A49 0662057A73 0662057A81 0662057A73 0662057A65 0662057A97 0662057B05 0662057A25 0662057A97 0662057A43 0662057A65 0662057A43 0662057A73 0662057A97 0662057A73 0662057A65 0662057A73 0662057A65 0662057A43 0662057A65 0662057A89 0662057A85 0662057A65 0662057A73 0662057B05 0662057A89 0662057B05 0662057B22 0662057B14 0662057A65 0662057A73 0662057A73 0662057R55 0662057R31 0662057A69 0662057A81 0662057B47 0662057A51 0662057C87 0662057A49 0662057A73 0662057C87 0662057A57 0662057A01 0662057R92 0662057R67 0662057A81 0662057A61 0662057A97 0662057A81 0662057A57 0662057A42 0662057A25 0662057R30 0662057R45 0662057R60 0662057R30 0662057R60 PL-201022-O DESCRIPTION 10k 100k 10k 100 ohm 1k 470 ohm 10k 1k 0 ohm 47k 47.5k 1%; 1/10 W 68k 10k 100k 68k 47.5k 1%; 1/10 W 100k 22k 47.5k 1.5k 100k 1k 10.0k 100k 4.7k 1k 10k 22k 10k 4.7k 100k 200k 100 ohm 100k 560 ohm 4.7k 560 ohm 10k 100k 10k 4.7k 10k 4.7k 560 4.7k 47k 33k 4.7k 10k 200k 47k 200k 1M 470k 4.7k 10k 10k 7.50k 1%; 1/10 W 1.21k 1%; 1/10 W 6.8k 22k 0 ohm 1.2k 3.3k 1k 10k 3.3k 2.2k 10 ohm 47.5k 16.2k 22k 3.3k 100k 22k 2.2k 510 ohm 100 ohm 1k 1%; 1/10 W 3.74k 1%; 1/10 W 10k 1%; 1/10 W 1k 1%; 1/10 W 10k 1%; 1/10 W HLF9009A & HLF9010A Radio, 900 MHz, 12 W REFERENCE SYMBOL R721 R722 R723 R724 R725, 726 R727 R728 thru 731 R732 thru734 R736, 737 R740 R741, 742 R743 R5201 R5202 R5203 R5204 R5205 R5207 R5211 R5212 R5221 R5223 R5224 R5230 R5240 R5241 R5302 R5306 R5311, 5312 R5321 R5322 R5323 R5324, 5325 R5327 R5401 R5700 R5703 R5704 R5705 R5706 R5707 R5708, 5709 R5710 R5711 thru 5713 R5714 R5715 R5716 R5717 R5718 R5724 thru 5727 R5728 R5729 R5731 thru 5733 R5734 thru 5736 R5737, 5738 R5739, 5740 R5741 R5742 R5743 R5744, 5745 R5746 R5747 R5748 R5750, 5751 R5752 R5753 R5754 R5755 R5756, 5757 R6502 R6503 R6504 R6505 R6506 R6512 R6514, 6515 R6519 R6520 R6523 thru 6525 R6526 R6527, 6528 R6531, 6532 R6537 thru 6539 MOTOROLA PART NO. 0662057A67 0662057A81 0662057A97 0662057A61 0662057A73 0662057A81 0662057G13 0662057A65 0662057A65 0662057A57 0662057A53 0662057A49 0662057A76 0662057A85 0662057A69 0662057A25 0662057A56 0662057B47 0662057A47 0662057A67 0662057B01 0662057A70 0662057A76 0662057A89 0683962T49 0662057B47 0662057A33 0662057A29 0662057A76 0662057A33 0662057A01 0662057A36 0662057A39 0662057B47 0662057A18 0662057A57 0662057A73 0662057A37 0662057A73 0662057A42 0662057A61 0662057B05 0662057A73 0662057A65 0662057A59 0662057A57 0662057A58 0662057A59 0662057A53 0662057A42 0662057A37 0662057A29 0662057A25 0662057A18 0662057A09 0662057A18 0662057A01 0662057A69 0662057A73 0662057A31 0662057A73 0662057A69 0662057A09 0662057A59 0662057A37 0662057A13 0662057A37 0662057A09 0662057A35 0662057A09 0662057A01 0662057A42 0662057A49 0662057A09 0662057A25 0662057A61 0680361L01 1705603W01 0662057A53 0662057A01 0662057A43 0662057A25 0662057A17 PL-201022-O DESCRIPTION 5.6k 22k 100k 3.3k 10k 22k 100k 4.7k 4.7k 2.2k 1.5k 1k 13k 33k 6.8k 100 ohm 2k 0 ohm 820 ohm 5.6k 130k 7.5k 13k 47k 100 ohm 0 ohm 220 ohm 150 ohm 13k 220 ohm 10 ohm 300 ohm 390 ohm 0 ohm 51 ohm 2.2k 10k 330ohm 10k 510 3.3k 200k 10k 4.7k 2.7k 2.2k 2.4k 2.7k 1.5k 510 ohm 330 ohm 150 ohm 100 ohm 51 ohm 22 ohm 51 ohm 10 ohm 6.8k 10k 180 10k 6.8k 22 ohm 2.7k 330 ohm 33 ohm 330 ohm 22 ohm 270 ohm 22 ohm 10 ohm 510 ohm 1k 22 ohm 100 ohm 3.3k therm 47k shunt, 1.639 mH 1.5k 10 ohm 560 ohm 100 ohm 47 ohm HLF9009A & HLF9010A Radio, 900 MHz, 12 W REFERENCE SYMBOL R6555 MOTOROLA PART NO. 0662057A33 220 ohm switch: 2-position shield: LNA shield mixer shield IF amplier shield MMIC shield VCO shield buffer shield synthesizer shield integrated circuit: (see note 1) MC68HC11K1 FLASH memory SRAM EEPROM 1 of 8 DCD/demux 74HC138A AND quad 2 INP MC74AC08D ASFIC quad op-amp switch, SPDT switch, SPDT dual op-amp hear clear IC audio PA switch SPDT dual op-amp dual op-amp 9.3 V regulator LM2941 voltage regulator LP2951AC quad op-amp D/A converter 6-bit 4-ch. with SPI IFIC mixer DBL balanced 16.8 MHz ref. oscillator MMIC frac-N sythesizer regulator 5 V 500 mA MC78M05BDT switch FMC2 microstrip line resonator 890-950 MHz, 18 W; 12.5 V switch FMC2 Zener diode: (see note 1) 10 V 5%; 225 mW MMBZ5240BL 5.1 V 5%; 225 mW MMBZ5231B 33 V 5%; 225 mW MMBZ5257B 14 V 5%; 225 mW MMBZ5244L 14 V 5%; 225 mW MMBZ5244L 5.1 V 5%; 225 mW MMBZ5231B 14 V 5%; 225 mW MMBZ5244B 5.1 V 5%; 225 mW MMBZ5231B 14 V 5%; 225 mW MMBZ5244L 33 V 5%; 225 mW MMBZ5257B 5.1 V 5%; 225 mW MMBZ5231B 5.1 V 5%; 225 mW MMBZ5231B 5.1 V 5%; 225 mW MMBZ5231B 12 V 5%; 225 mW MMBZ5242B crystal: (see note 2) lter 45.1 MHz lter 45.1 MHz resonator 44.6450 MHz PL-201022-O DESCRIPTION
Parts List for HLF9009A & HLF9010A Main Boards
C100 C101 thru 103 C104 C105 C106 C107 C108 C109, 110 C111 C113, 114 C131 C132 C133 thru 135 C136, 137 C146 C151 C200 C201 C202 C203, 204 C205 C206 C207 C208 C209 C210 C211, 212 C221 C222 C223 C224 C225 C226 C227 C228 C229 C230 C231 C232 C233 C234 C237 C241 thru 243 C251 C252 C253 C254 C300 C350 C351, 352 C353 C354 C355, 356 C357 C358 C360, 361 C362 C363, 364 C365 C367 C374 C401 C402 C404 C405, 406 C407, 408 C409 C410 C411 C412, 413 C414 C415, 416 C418 C419 C421 thru 423 C425 thru 427 C431 C442 C451 C460 C601
2113740F41 2113743K15 2113741F49 2311049A42 2113743K15 2113741F49 2113741F25 2113740F41 2113741F49 2113741F49 2113743K15 2311049A07 2113743K15 2113740F41 2113740F36 2113743K15 2113743K15 2113740F41 2113741F17 2113740F41 2113743F08 2113743K15 2113743F08 2113741F13 2311049J26 2113741A53 2113743A19 2113743K15 2311049A07 2113741A57 2311049J11 2113741F49 2113743K15 2311049J44 2311049A01 2113741F49 2311049J11 2113741F49 2311049J26 2113740F39 2113743K15 2113741A57 2113740F41 2113743K15 2311049J23 2311049A07 2113743K15 2113743A23 2113743A19 2113741F17 2311049A04 2113741F49 2311049A42 2113741F49 2311049A04 2113743K15 2113743A19 2113741A33 2113743K15 2113741A33 2113741F49 2113743K15 2113741F37 2311049J44 2113741F25 2113741F49 2109720D14 2113740F41 2113741F49 2113740F41 2113741F25 2113740F41 2311049J11 2311049J44 2113740F41 2113740F41 2113740F41 2113740F41 2113740F41 2311049A09 2113740F41
S401
4085797L01
SH5201 SH5202 SH5203 E5700 E5701 E5702, 5703 E5704
2605261V01 2605417V01 2605417V01 2602660J02 2604668E02 2602660J02 2680524L01
CR150, 151 CR721 CR5700 CR5701, 5702 CR6501 CR6502, 6503 CR6504 CR6506 CR6508 CR6509 D101, 102 D200 D401, 402 D403 D611 D621 D631 D5201 D5303
4813833C02 4813833C02 4802233J09 4862824C01 4813833C02 4802482J02 4805129M96 4805218N57 4813832B35 4805218N57 4813833C02 4813833C02 4880939T01 4813833C02 4813833C02 4813833C02 4813833C02 4880154K03 4880154K03
Q101 thru 103 Q141 Q150 Q200 Q401 Q410 Q411 Q415 Q450 Q460, 461 Q601 Q611 Q612 Q731 Q741 Q742 Q5201 Q5230 Q5301 Q5700 Q5701 Q5702 thru 5704 Q5705 Q5706, 5707 Q6501 Q6506
4880048M01 4880048M01 4882033T01 4880214G02 4880214G02 4880048M01 4880052M01 4880494U01 4880048M01 4880048M01 4880214G02 4805128M27 4880214G02 4880214G02 4880048M01 4805128M27 4813827A07 4813824A17 4813827A18 4880048M01 4813824A17 4809527E01 4804188K01 4809527E01 4813827A26 4813824B01
U101 U102 U103 U104 U105 U106 U201 U202 U203 U204 U251 U350 U401 U402 U403 U460 U601 U631 U701 U702 U5201 U5211 U5700 U5701 U5702 U5703 U5704, 5705 U5706, 5707 U6501 U6502
5180421V01 5108444S61 5185963A21 5108444S49 5113805A30 5113808A07 5105835U45 5113819A04 5109522E13 5109781E79 5113818A03 5105835U50 5109699X01 5180173M02 5113818A10 5113818A03 5105625U25 5105469E65 5113819A02 5113811G02 5180207R01 5185670L01 5105279V31 5105109Z59 5105457W46 5113816A07 4805921T02 4804122K04 5113829D23 4805921T02
F401
6585711L05
FL5201 FL5202 FL5203, 5204
9185747L01 9180098D14 9102603S25
J100 J400 J6501 J6502
0902636Y01 2804503J01 0905901V06 0905902V04
L131, 132 L200 L403 thru 413 L414 thru 416 L418 L419 L420 thru 428 L429, 430 L431 thru 434 L435 L5201 L5203
2462587Q40 2462587P30 2402601S05 2484657R01 2402601S05 2484657R01 2402601S05 2484657R01 2402601S05 2484657R01 2462587M19 2462587T30
R100 R101 thru 103 R104 R105 R106 R107 R108 R109, 110 R111, 112 R113 R114 R115, 116 R121 R122 R123 R126 R127 R131 R132 R133 R135, 136 R142 R145 R146, 147 R150 R151 R152 R153 R155
0662057A65 0662057B05 0662057A89 0662057A65 0662057A73 0662057A57 0662057A73 0662057A35 0662057A65 0662057A85 0662057A93 0662057A73 0662057A65 0662057A89 0662057A73 0662057A73 0662057A65 0662057A65 0662057A81 0662057A97 0662057A73 0662057A73 0662057A73 0662057A35 0662057A89 0662057B05 0662057A56 0662057A85 0662057A89
VR101 VR410 VR412 VR415, 416 VR421, 422 VR425 VR426, 427 VR430 VR431 VR441 VR451 VR621 VR641 VR650
4813830A23 4813830A14 4813830A40 4813830A27 4813830A27 4813830A14 4813830A27 4813830A14 4813830A27 4813830A40 4813830A14 4813830A14 4813830A14 4813830A25
Y5201 Y5202 Y5211
9102651Y01 9102651Y02 4802653Y01
notes: 1. For optimum performance, diodes, transistors, and integrated circuits must be ordered by Motorola part numbers. 2. When ordering quartz crystal units or ceramic resonators, specify carrier frequency, crystal (or resonator) frequency, and crystal (or resonator) type number.
16
6880906Z19-O
September, 2000
J101
1 2 INT_SPKR+ INT_SPKR-
J901
18 17
J902
1 INT_SPKR+ 2 INT_SPKR+5V
R980 0
15 4 3 16 14
4 BUS+ 15 PTT 16 HOOK 3 MIC 5 HANDSET_AUDIO C901 470pF C902 470pF
R901 270
J903
7 BUS+ 6 PTT 3 HOOK 5 MIC_HI 8 HANDSET_AUDIO TP901 1 N.C. 2 N.C. R902 4 GND 1K R931 N.U.
Q953 N.U.
R981 200K
U932
22 VDD 20 19 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29
DISPLAY UNCATALOGED !!!
R933 R932 N.U. 100K C934 0.1UF C935 0.01UF
21
OUTPUT_B-1 OSC-IN OUTPUT_B-2 OUTPUT_B-3 OUTPUT_B-4 OUTPUT_B-5 OUTPUT_B-6 OUTPUT_B-7 OUTPUT_B-8 OUTPUT_B-9 OUTPUT_B-10 CLOCK-IN DATA-IN N.C N.C N.C N.C OUTPUT_B-11 OUTPUT_B-12 OUTPUT_B-13 OUTPUT_B-14 OUTPUT_B-15 OUTPUT_B-16 OUTPUT_B-17 OUTPUT_B-18 OUTPUT_B-19 OUTPUT_B-20 OUTPUT_B-21 OUTPUT_B-22 OUTPUT_B-23 OUTPUT_B-24 OUTPUT_B-25 OUTPUT_B-26 OUTPUT_B-27 OUTPUT_B-28 BACKPLANE-IN BACKPLANE-OUT OUTPUT_B-29 OUTPUT_B-30 OUTPUT_B-31 OUTPUT_B-32 OUTPUT_B-33
H931
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 1 2 3 4 5 6 7 8 9 10 11 12 13 14
9 17 7
10 +5V 2 FLT_A+ 12 GND +5V FLT_A+
VR901 5.1v
VR902 5.1v
VR903 14V
VR904 14V
VR905 14V
FLT_A+
24 25
TP902 6 5 8 12 13 SPI_DATA_BUF 14 SPI_CLCK_BUF 11 LCD_CE 7 LED_CE C903 NU C904 NU C972 NU C973 NU VR906 5.1v VR0907 5.1v VR908 5.1V VR909 NU
NC NC NC NC
28 23 18 1
27 26
FLEX
10 ANALOG_1
VSS
9 +5V C911 NU FLT_A+ U942 R974 1M R973 200K C970 2.2UF 2 6 5 R971 200K R970 47K 2.2K R956 47K VR993 14V 1 U970 3 ON/OFF R982 5 FLT_A+ 3 4 VOLUME DOWN 1 VOLUME UP 2
CONTROLLER
FLT_A+
8 18 1 ON_OFF_CONTROL R925 CR925 4.7K C971 NU NC R926 4.7K R972 470K 4 7 U970
D951 green
D955 green
D959 green
D963 green
D967 green
FLT_A+ ON OFF D952 green D956 green D960 green D964 green LED (POT) +5V D941 yellow D953 green D942 yellow 1
TOUCH_SW
Q925 R919 4.7K R957 24K R955 4.7K PB915 2

TOUCH_SW
R920 4.7K PB916 2

TOUCH_SW
R921 4.7K PB917 2

TOUCH_SW
R922 4.7K PB918 2 4 6 D943 red D944 green
D957 green
D961 green
D965 green
D969 green
1 3 5
1 3 5
1 3 5
4 6 6 ANALOG_3
4 6
4 6
3 5 R941 +5V
Q942
Q943
Q944
D954 green
D958 green
D962 green
D966 green
D970 green
GOLD_SW_6P PHONE C925 NU R958 4.7K PB925 1

TOUCH_SW
GOLD_SW_6P SCAN
GOLD_SW_6P CALL
GOLD_SW_6P 10K MENU +5V Q941 R942 47K C941 0.1UF R943 47K R944 270 R945 47K R946 270 R947 47K R948 270 R951 20K R952 U941
16
13
Q951 Q952
R915 4.7K PB913 2 4 6 2

TOUCH_SW
R916 4.7K PB914 1 3 5 2

TOUCH_SW
R917 4.7K PB921 1 3 5 2

TOUCH_SW
R918 4.7K PB922 1 3 5 2

TOUCH_SW
20K
VDD 4 Q1 5 6 7 14 13 12 11 10 9
1
1
R953 10K
R954 10
Q2 Strobe Q3 Q4 OE Clock Data QS_ QS VSS 8 Q5 Q6 Q7 Q8
3 5 8 ANALOG_2
4 6
4 6
4 6
4 6
3
15
5
3
NC NC
GOLD_SW_6P
GOLD_SW_6P
GOLD_SW_6P
GOLD_SW_6P_SHORT
GOLD_SW_6P_SHORT
2
11
MON C915 NU
HM
SEL C942 10uF
NC NC
Schematic Diagram for FLN8744A Control Head

September, 2000 6880906Z19-O
17
Parts List
FLN8744A Control Head Board REFERENCE SYMBOL MOTOROLA PART NO. PL-201002-O DESCRIPTION capacitor, xed: uF +/-5%; 50 V: unless otherwise stated 2.2 470 pF ceramic 0.1 pF 0.01 pF ceramic 0.1 tantalum 10 10%; 7 V diode: (see note) dual 70 V common cathode light emitting diode: (see note) yellow red green green green display_LCD connector, receptacle: connector, ex cable, side entry SMT header mic connector transistor: (see note) NPN DIG 47k/47k NPN DIG 47k/47k NPN 40 V 0.2A general purpose NPN 25 V 5A NPN_MJD200T4 resistor, xed: +/-5%; 1/8 W: unless otherwise stated 4.7k 47k 24k 4.7k 47k 200k 470k 200k 1 Meg. 0 ohm 200k 2.2k 270 ohms 1k 4.7k 4.7k 100k 10k 47k 270 ohms 47k 270 ohms 47k 270 ohms 20k 20k 10k 10 ohms integrated circuit: (see note) potentiameter switch high performance single supply MM5453VX MC14094B Zener diode: (see note) 5.1 V 5% 225 mW MMBZ5231B 14 V 5% 225 mW MMBZ5244L 14 V 5% 225 mW MMBZ5244L
VIEWED FROM SIDE 1
C970 C901, 902 C934 C935 C941 C942
2311049A09 2113741F17 2113743K15 2113741F49 2113743K15 2311049J23
PB922
1
D943 D953 D957 D961 D965 D969 D964 D956
U942
D942 D941
PB913 PB921
D954 D958 D962 D966
CR925
4813833C02
D941, 942 D943 D944 D951 thru 967 D969, 970 H931
4805729G73 4805729G74 4805729G75 4805729G75 4805729G75 7202662Y01
D970
D944
D960
H931
PB914
J901 J902 J903
0902636Y01 2809926G01 2805924V01
J903
D951 D955 D959 D963 D967
Q925 Q941 Q942 thru 944 Q951 Q952
4880048M01 4880048M01 4813824A10 4813824A10 4813822A20
PB925
PB915
PB916
PB917
PB918
C792 C793
R955 R956 R957 R958 R970 R971 R972 R973 R974 R980 R981 R982 R901 R902 R915 thru 922 R925, 926 R933 R941 R942, 943 R944 R945 R946 R947 R948 R951 R952 R953 R954
0662057A65 0662057A89 0662057A82 0662057A65 0662057A89 0662057B05 0662057B14 0662057B05 0662057B22 0662057B47 0662057B05 0662057A57 0662057C61 0662057A49 0662057A65 0662057A65 0662057A97 0662057A73 0662057A89 0662057C61 0662057A89 0662057C61 0662057A89 0662057C61 0662057A80 0662057A80 0662057A73 0680194M01
VIEWED FROM SIDE 2
CR925 R926 C925
C791
D952
R925 VR909
C901 VR993 R956 R982 VR901
39
R958
29
VR908 R981 R980
R918
R917 R946
R945 Q925 Q943 R943 Q942 R957
C903 C915 C911 C904 R915
40
28
C934
Q953 R931 R941 R932 R944 C941
VR903 VR904 R901
J901
VR906
R916
R933
Q941
U932
C935 1
+
R942
R947 C942 R948 R970 TP901 1 R973
16
Q952
R951 R952 R953 Q951
Q944
VR907
J902
U942 U970 U932 U941
1805642V01 5113818A03 5105625U61 5113806A35
7 18
R922 R921 R920
17
R955 R919 8 9
R095
5 R971
R902
18
U941
U970
TP902
C902
R972 R974 C970
VR902
VR905
VR908 4813830A14 VR901 thru 907 4813830A27 VR993 4813830A27
note: For optimum performance, diodes, transistors, and integrated circuits must be ordered by Motorola part numbers.
Circuit Board Details & Parts List for FLN8744A Control Head 18
6880906Z19-O September, 2000
Parts List
GTX Mechanical Parts List; 30 W PL-201019-O DESCRIPTION exterior volume knob logo label interior volume knob housing LCD frame gasket keypad LCD display connector LCD frame control head board exible circuit control head gasket assembly, cover main board PA shield mechanical screw, M3x0.5x18 power cable PM shield clip spring accessory kit accessory connector gasket accessory clamp chassis FCC label speaker pad connector speaker trunnion kit LABEL
18 17 15 19 23 21 16 20 22
REFERENCE SYMBOL 1 2 3 4 5 6 7 8 9 10 11 12 13, 14, 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30, 31, 32
MOTOROLA PART NO. 3605422W02 5480643K01 3608147K01 1580356K01 3280511L01 7580358K01 7202631Y01 2802638Y02 0780360K01 FLN8744 8402618Y01 3202620Y01 0185808L01 ---0185787M01 0310907A20 3080562V02 2680567V01 4205938V01 FHN5875 3202606Y01 4280587L01 2680547V01 ---7585697M01 2802638Y01 5080442U02 HLN9640 54-85743M01
24
14
non-referenced items
25
13 12
11 10 9 8 7 6 5 4 2 1
31 32
27 30
26
28
29
RPD-20118-0
GTX Exploded View & Mechanical Parts List, 30 W

September, 2000 6880906Z19-O
19
Parts List
GTX Mechanical Parts List; 12 W REFERENCE SYMBOL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28, 29 MOTOROLA PART NO. 3605422W02 5480643K01 3608147K01 1580356K01 3280511L01 7580358K01 7202631Y01 2802638Y02 0780360K01 FLN8744 8402618Y01 3202620Y01 2680439K01 3202619Y01 1580355K01 ---2680519K01 0310907A20 4205938V01 4280587L01 3202606Y01 FHN5875 2780354K01 ---7585697M01 2802638Y01 5080442U02 GLN7317 PL-201020-O DESCRIPTION exterior volume knob logo label interior volume knob housing LCD frame gasket keypad LCD display connector LCD frame control head board exible circuit control head gasket cover shield cover gasket cover assembly main board PA shield mechanical screw, M3x0.5x10 clip spring accessory clamp accessory connector gasket accessory kit chassis FCC label speaker pad connector speaker trunnion kit
15
18 17
19 20 21
16
22
14
23 13 12
10
11
9 8 7 6 5 4 2 1 3 26 28 29 25 24
27 RPD-20102-0
GTX Exploded View & Mechanical Parts List, 12 W 20

6880906Z19-O September, 2000
REPLACEMENT PARTS ORDERING

ORDERING INFORMATION When ordering replacement parts or equipment information, the complete identication number should be included. This applies to all components, kits, and chassis. If the component part number is not known, the order should include the number of the chassis or kit of which it is a part, and sufcient description of the desired component to identify it. Crystal and channel element orders should specify the crystal or channel element type number, crystal and carrier frequency, and the model number in which the part is used. Orders for active lters, Vibrasender and Vibrasponder resonant reeds should specify type number and frequency, should identify the owner/operator of the communications system in which these items are to be used, and should include any serial numbers stamped on the components being replaced. MAIL ORDERS Send written orders to the following addresses:
Replacement Parts/ Test Equipment/Manuals Crystal Service Items: Motorola Inc. Americas Parts Division Attention: Order Processing 1313 E. Algonquin Road Schaumburg, IL 60196
Federal Government Orders: Motorola Inc. Americas Parts Division Attention: Order Processing 7230 Parkway Drive Landover, MD 21076
International Orders: Motorola Inc. Americas Parts Division Attention: International Order Processing 1313 E. Algonquin Road Schaumburg, IL 60196
TELEPHONE ORDERS Americas Parts Division: 1-800-826-1913 (For Federal Government Orders) Call: 847-576-8012 1-847-538-8023 (International Orders) TELEX/FAX ORDERS Americas Parts Division:FAX: 847-538-8198 (Domestic) 847-576-3023 (International) Parts ID: 847-538-8194 Telex: 280127 (Domestic) 403305 (International) Federal Government Orders: FAX: 410-712-4991
PARTS CUSTOMER SERVICE
PRODUCT CUSTOMER SERVICE
Americas Parts Division: Call: 1-800-422-4210 Parts Identication: Call: 847-538-0021
Customer Response Center (Sales and Service Assistance): Call: 1-800-247-2346 FAX: 1-800-232-9272
Motorola, Inc. Radio Products Group 1000 W. Washington St. Mt. Pleasant, IA 52641 Copyright 2000 Motorola, Inc. All Rights Reserved Printed In U.S.A.
6880906Z19-O

Engineering GTX

Uploaded by

Copyright:

Available Formats

Engineering GTX

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Engineering GTX

Uploaded by

Copyright:

Available Formats

What is the purpose of the document?

What is the purpose of the document?

What rights does the license grant to the user?

What rights does the license grant to the user?

GTX LTR / Privacy Plus

Product Software License Agreement

Computer Software Copyrights

Test Equipment, Service Aids, and Tools

Test Mode, Error Codes and Performance Tests

Disassembly & Reassembly For 12 W Models

Disassembly & Reassembly For 30 W Models

Radio Tuning Procedure

Schematic Diagrams, Circuit Board Details, and Parts Lists

Foreword Scope of Manual

GTX LTR / Privacy Plus 900 MHz Mobile Service Manual

How to Use This Manual

Ordering Replacement Parts

GTX LTR / Privacy Plus 900 MHz Mobile Service Manual

Foreword Model Chart

GTX LTR, 900 MHz, 12.5 kHz, 12 W

Main Board, Privacy Plus, 12.5 kHz, 12 W HLF9009_ X X

Control Head Board

Main Board, LTR, 12.5 kHz, 12 W

Foreword Model Chart

GTX LTR / Privacy Plus 900 MHz Mobile Service Manual

GTX Privacy Plus, 900 MHz, 12.5 kHz, 30 W

GTX LTR, 900 MHz, 12.5 kHz, 30 W

Main Board, Privacy Plus, 12.5 kHz, 30 W HLF9003_ X X

Control Head Board

Main Board, LTR, 12.5 kHz, 30 W

GTX LTR / Privacy Plus 900 MHz Mobile Service Manual

7.5 W External Speaker

Trunnion Kit; 30 W Trunnion Kit; 12 W

900 MHz, 3 dB Gain w/14 ft. Cable

Foreword Maintenance Specifications

GTX LTR / Privacy Plus 900 MHz Mobile Service Manual

GTX LTR / Privacy Plus 900 MHz Mobile Service Manual

Foreword Maintenance Specifications

All specications subject to change without notice.

Foreword Radio Model Numbering System

GTX LTR / Privacy Plus 900 MHz Mobile Service Manual

Radio Model Numbering System

GTX Privacy Plus

GTX LTR / Privacy Plus 900 MHz Mobile Service Manual

Foreword Radio Model Numbering System

GTX Privacy Plus

Foreword Radio Model Numbering System

GTX LTR / Privacy Plus 900 MHz Mobile Service Manual

Scope of this Manual

Introduction Air Bag Warning

GTX LTR/Privacy Plus 900 MHz Mobile Service Manual

Air Bag Warning

involved in your communication equipment installation.

Section 2 Basic Maintenance

Circuit Boards and Components

Safe Handling of CMOS Devices

Basic Maintenance Repair Procedures and Techniques

GTX LTR/Privacy Plus 900 MHz Mobile Service Manual

Repair Procedures and Techniques