1.105 Solid Mechanics Laboratory Fall 2003: Experiment 6 The Linear, Elastic Behavior of A Beam
1.105 Solid Mechanics Laboratory Fall 2003: Experiment 6 The Linear, Elastic Behavior of A Beam
To experimentally study the linear elastic behavior of beams under four point bending. To compare the stiffness of beams of the same length and cross-sectional area but having different proles. To measure the extensional strain in the top and bottom bers of the beam specimens and compare with the prediction of engineering beam theory.
Each beam specimen, made of Aluminum and 24 inches long, will be simply supported at its ends and loaded at two points symmetrically disposed with respect to midspan, each 3 inches off cen ter. This four point bending produces pure bending (no shear) over the midspan section. Two dial gages will be employed, one to measure midspan deection, the other will be positioned to measure vertical displacement roughly half the distance between midspan and one of the ends. Two strain gages are mounted on the top and on the bottom at midspan. The beams will be loaded using dead weights as in the previous experiment. You will compare bending strain and beam stiff ness to theory.
Beam Specimens
The gure below shows a beam specimen under four point bending. To the right we show the cross sections of the two Aluminum specimens. The material is 6061-T6 as is clearly indicated on the beams sides.
Same areas
The two have the same cross sectional area as you can verify. Measure all the relevant dimensions, e.g., the length of the span between the supports, all crosssection dimensions, the location of the two load points relative to the supports. You will test the I beam in one orientation, as indicated in the gure. You will test the beam with rectangular cross section in two orientations - in the orientation indicated in the gure and with the beam lying at on the supports. You will make a total of three runs minimum. Multiple runs are suggested, especially with the rst specimen, to acclimate yourself to the beams behavior and instrumentation performance.
eo op amp output
bridge pot
amp pot
Turn on the power supply and, with the Digital Multimeter, check the voltages at the strain gage input terminals. One should read +10v, another approximately +5v and the third should read 0v. Balance the bridge. Null the amplier. Calibrate the amplier by resetting the bridge balancing pot so that the output of the bridge (which is the input to the amplier) is on the order of 10 mv, then measure the output of the amplier to obtain the gain. Repeat this for a bridge output of approximately 20mv.
Fall 2003
lbs. total.
When done, turn off the power supply but leave all connections as is.
Report
Start with a one paragraph executive summary of the purpose, the method, the results of the lab tests. Include a short section on experiment proceedure which, rather than reproduce the steps set out above, makes note of any particular difculties you encountered and how you managed to over come them. Included in this section your op-amp calibration data and your calculation of amplier gain. In your section on "results", you will compare experiment with engineering beam theory. The rela tionships summarized in the Appendix will allow you to deduce and evaluate:
The bending stiffness, EI The bending moment, hence the normal stress, hence the extensional strain
at the top and bottom of the beams.
Fall 2003
A plot of displacement versus load for each of the three beam specimens.1
Plot also the off center displacement versus midspan load. Show on each plot the results of engineering beam theory.
Plot the strain at the top (or bottom) versus load for each of the three speci
mens. Show on each plot the results of engineering beam theory.
A table showing the bending stiffnesses obtained from the strain measures.
(From the strain you can compute the curvature. From the load values and lengths measured you can compute the bending moment in the mid section. The ratio is the bending stiffness). Include in the table the "theoretical values". In a "conclusions" section, include recommendations for improvement of the experience.
1. We consider the two orientations of the beam of rectangular cross-section as two different beam speci mens.
Fall 2003 November 13, 2003 4
Appendix
Engineering Beam Theory Engineering beam theory shows that the most signicant stress is the normal stress component on an x face; x in the example at the right. It is related to the applied loads by
y
Mb
x
x , x L P a y, v P a x
Mb y x = -------------I
where y is the distance from the neutral axis which, for a doubly symmetric beam, is at the center of the cross-section and I is the moment of inertia of the cross section.
I = y d
A
A
For a rectangular cross-section of width b and height h, this is I = bh3/12 The applied loads come in through the bend ing moment Mb. The convention for positive shear and bending moment is shown in the gure. The extensional strain, from the stress/strain relations is just:
Mb.
Mb.
x = x E
The bending stiffness is dened as the product E I as it appears in the moment-curvature relation ship
1 M b = ( EI ) - R
displacement of the neutral axis by, (1/R) = d2v/dx2 . An integration of the differential equation obtained from the moment curvature relation gives, for the case where the beam is loaded as shown, the mid-span deection
midspan
Pa 2 2 (3L 4a ) = ---------- 24 EI
Fall 2003
While this is not required of you, to deter mine the displacement at some point other than the mid-span, you can use the relationships below and the superpositioning of two symmetrically placed, loads P, to obtain an expression for v(x). Note that the origin of the x axis is located at the left end of the beam. For x < a:
L v a P b
x
Pb 3 2 2 - [ x + (L b ) x] v ( x ) = ----------- 6 LEI
For x > a:
Pb L 3 3 2 2 - -- ( x a) x + (L b ) x v ( x ) = ----------- 6 LEI b
Later in the semester we will make use of the program, Fameworks, to model these three beams, then compare the computer results with experiment.
Fall 2003
Strain-gage Circuit. Two strain gages are xed to top and bottom anges. The top will experience contraction, the bot tom extension. The bridge circuit is used to avoid attempting to measure the small difference of two large numbers and their placement in the bridge effectively doubles the sensitivity. The assumption is that the beam shows a doubly symmetric section so the magnitudes of the two strains are equal. The circuit you used in Experiment 3 has been altered to give us the measures we seek. The values of the resistances are: Vsupply = +10 v Ra = 348 +/- 5% ohms Rb = 561 +/- 5% ohms Rg - R e1 e2 Rb Rg+R Rpot Ra Rg = 350 +/-0.2% ohms Rpot = 1 kohm (max) The ouput of the bridge as a function of the change in resistance, R, e1 - e2 = (Vsupply /2)(R/Rg) The strain as a function of change in resistance is given by
= (1/Fgage)(R/Rg)
where Fgage is the "gage factor" stated by the manufacturer1 to be Fgage =2.07 +/- 0.5%
With these, you can compute the strain in the member, given the voltage difference e1-e2.
The voltage difference e1 - e2 is obtained from your measured values at the op-amp output by dividing by the amplier gain.