博士班資格考 電子學題庫

Download as pdf or txt
Download as pdf or txt
You are on page 1of 15

1. The following figure shows a signal source connected to the input of an amplifier.

Here Rs is the source resistance, and Ri and Ci are the input resistance and input capacitance, respectively, of the amplifier. Derive an expression for Vi(s)/Vs(s). Is this circuit a high-pass, low-pass, or band-pass filter? Find the 3-dB frequency for the case Rs = 20 k, Ri = 80 k, and Ci = 5 pF.

2. Assuming that the diodes in the circuits of the following figures are ideal, find the values of the labeled voltage and currents.

(a)

(b)

3. A particular design of a voltage regulator is shown below. Diode D1 and D2 are 10 mA units; that is, each has a voltage drop of 0.7 V at a current of 10 mA. Each has n = 1. (a) Find VO with no load. (b) What is the regular output voltage VO with the 150 load connected? (c) With the load connected, to what value can the 5 V supply be lowered while maintaining the loaded output voltage within 0.1 V of its nominal value?

4. Sketch the transfer characteristic vO versus vI for the limiter circuits shown in the following figures, assuming that the diodes are modeled with the piecewise-linear model with VD0 = 0.65 V and rD = 20 .

(a)

(b

5. For the circuits in the following figures, each utilizing an ideal diode, sketch the output for the input shown. Label the most positive and most negative output levels. Assume CR >> T. (15%)

(b) (a) 6. An n-channel device has kn' = 50 A/V2, Vt = 0.8 V, and W/L = 20. The device is to operate as a switch for small vDS, utilizing a control voltage vGS in the range 0 V to 5 V. Find the switch closure resistance, rDS, and closure voltage, VDS, obtained when vGS = 5 V and iD = 1 mA. 7. Consider a CMOS process for which Lmin = 0.8 m, ox = 3.4510-11F/m, tox = 15 nm, un = 550 cm2/V.s, and Vt = 0.7 V. (a) Find Cox and kn'. (b) For an NMOS transistor with W/L = 16 m/0.8 m, calculate the values of VOV, VGS, and VDSmin needed to operate the transistor in the saturation region with a dc current ID = 100 A. (c) For the device in (b), find the value of VOV and VGS required to cause the device to operate as a 1000 resistor for very small VDS. 8. An NMOS transistor, fabricated with W = 100 m and L = 5 m in a technology for which kn' = 50 A/V2 and Vt = 1V, is to be operated at very low values of vDS as linear resistor. For vGS varying from 1.1 V to 11 V, what range of resistor values can be obtained? What is the available range if (a) the device width is halved? (b) the device length is halved? (c) both the width and length are halved?
2

9. An NMOS transistor is fabricated in a 0.8 m process having kn' = 130 A/V2 and VA' = 20 V/m of channel length. If L = 1.6 m and W = 16 m, find VA and . Find the value of ID that results when the device is operated with an overdrive voltage of 0.5 V and VDS = 2 V. Also, find the value of r0 at this operating point. If VDS is increased by 1 V, what is the corresponding change in ID? 10. All the transistors in the circuits shown below have the same values of |Vt|, k', W/L, and . Moreover, is negligibly small. All operate in saturation at ID = I and |VGS| = |VDS| = 3 V. Find the voltages V1, V2, V3, and V4. If |Vt| = 1 V and I = 2 mA, how large a resistor can be inserted in series with each drain connection while maintaining saturation? What is the largest resistor that can be placed in series with each gate? If the current source I requires at least 2 V between its terminals to operate properly, what is the largest resistor that can be placed in series with each MOSFET source while ensuring saturated-mode operation of each transistor at ID = I? In the latter limiting situation, what do V1, V2, V3, and V4 become?

11. The PMOS transistor in the circuit below has Vt = -0.7 V, upCox = 60 A/V2, L = 0.8 m, and = 0. find the values required for W and R in order to establish a drain current of 115 A and a voltage VD of 3.5 V.

12. The NMOS transistors in the circuit below have Vt = 1 V, unCox = 120 A/V2, = 0, and L1 = L2 = L3 = 1 m. Find the required values of gate width for each of Q1, Q2, and Q3 to obtain the voltage and current values indicated.

13. Design the circuit below so that the transistor operates in saturation with VD biased 1 V from the edge of the triode region, with ID = 1 mA and VD = 3 V, for each of the following two devices ( use a 10 A current in the voltage divider): (a) |Vt| = 1 V and kp'W/L = 0.5 mA/V2 (b)|Vt| = 2 V and kp'W/L = 1.25 mA/V2 For each case specify the values of VG, VS, R1, R2, RS, and RD.

14. In the circuit below, the NMOS transistor has |Vt| = 0.9 V and VA = 50 V and operates with VD = 2 V. What is the voltage gain vo/vi? what do VD and the gain become for I increased to 1 mA?

15. The figure below shows a discrete-circuit CS amplifier employing the classical biasing scheme. The input signal vsig is coupled to the gate through a very large capacitor (shown as infinite). The transistor source is connected to ground at signal frequencies via a very large capacitor (shown as infinite). The output voltage signal that develops at the drain is coupled to a load resistance via a very large capacitor (shown as infinite).
4

(a) If the transistor has Vt = 1 V, and kn'W/L = 2 mA/V2, verify that the bias circuit establishes VGS = 2 V, ID = 1 mA, and VD = +7.5 V. That is, assume these values, and verify that they are consistent with the values of the circuit components and the device parameters. (b) Find gm and ro if VA = 100 V. (c) Draw a complete small-signal equivalent circuit for the amplifier assuming all capacitors behave as short circuits at signal frequencies. (d) Find Rin, vgs/vsig, vo/vgs, and vo/vsig

16. A common-gate amplifier using an n-channel enhancement MOS transistor for which gm = 5 mA/V has a 5 k drain resistance (RD) and a 2 k load resistance (RL). The amplifier is driven by a voltage source having a 200 resistance. What is the input resistance of the amplifier? What is the overall voltage gain Gv? If the circuit allows a bias-current increase by a factor of 4 while maintaining linear operation, what do the input resistance and voltage gain become? 17. The source follower below uses a MOSFET biased to have gm = 5 mA/V and ro = 20 k. Find the opencircuit voltage gain Avo and the output resistance. What will the gain become when a 1 k load resistance (RL) is connected?

18. The MOSFET in the circuit below has Vt = 1 V, kn'W/L = 0.8 mA/V2, and VA = 40 V. (a) Find the values of RS, RD, and RG so that ID = 0.1 mA, the largest possible value for RD is used while a maximum signal swing at the drain of 1 V is possible, and the input resistance at the gate is 10 M.
5

(b) Find the values of gm and ro at the bias point. (c) If terminal Z is grounded, terminal X is connected to a signal source having a resistance of 1 M, and terminal Y is connected to a load resistance of 40 k, find the voltage gain form signal source to load. (d) If terminal Y is grounded, find the voltage gain from X to Z with Z open-circuited. What is the output resistance of the source follower? (e) If terminal X is grounded and terminal Z is connected to a current source delivering a signal current of 10 A and having a resistance of 100 k, find the voltage signal that can be measured at Y. For simplicity, neglect the effect of ro.

19. The current-steering circuit below is fabricated in a CMOS technology for which unCox = 200 A/V2, upCox = 80 A/V2, Vtn = 0.6 V, Vtp = -0.6 V, VAn' = 10 V/m, and |VAp'| = 12 V/m. If all devices have L = 0.8 m, design the circuit so that IREF = 20 A, I2 = 100 A, I3 = I4 = 20 A, and I5 = 50 A. Use the minimum possible device widths while achieving proper operation of the current source Q2 for voltages at its drain as high at +1.3 V and proper operation of the current sink Q5 with voltages at its drain as low as -1.3 V. Specify the widths of all devices and the values of R. Find the output resistance of the current source Q2 and the output resistance of the current sink Q5.

20. A signal-current amplifier is illustrated below. Here Q1 is a common-source amplifier fed with vI = VGS + vi, where VGS is the gate-to-source dc bias voltage of Q1 and vi is a small signal to be amplified. Find the signal component of the output voltage vO and hence the small-signal voltage gain vo/vi.
6

21. Find the midband gain AM and the upper 3-dB frequency fH of a CS amplifier fed with a signal source having an internal resistance Rsig = 100 k. The amplifier has RG = 4.7 M, RD = RL = 15 k, gm = 1mA/V, ro = 150 k, Cgs = 1 pF, and Cgd = 0.4 pF. 22. The following figure shows the high-frequency equivalent circuit of a common-source FET amplifier. The amplifier is fed with a signal generator Vsig having a resistance Rsig. Resistance Rin is due to the biasing network. Resistance RL is the parallel equivalent of the load resistance RL, the drain bias resistance RD, and the FET output resistance ro. Capacitors Cgs and Cgd are the FET internal capacitances. For Rsig = 100k, Rin = 420k, Cgs = Cgd = 1pF, gm = 4mA/V, and RL = 3.33k, find the midband voltage gain, AM = Vo/Vsig, the upper 3-dB frequency, fH, and the gain-bandwidth product in megahertz. Moreover, find the value of RL that will result in fH = 180kHz. Find the new values of the midband gain and of the gain-bandwidth product.

23. A CMOS common-source amplifier of the type shown in the following figure has W/L = 7.2m/0.36m for all transistors, nCox = 387 A/V2, pCox = 86 A/V2, IREF = 100 A, VAn = 5V/m, and |VAp| = 6V/m. For Q1, Cgs = 20fF, Cgd = 5fF, CL = 25fF, and Rsig = 10k. Assume that CL includes all the capacitances introduced by Q2 at the output node. Find fH using both the Miller equivalence and the open-circuit time constants. Also, determine the exact values of fP1, fP2, and fZ and hence provide another estimate for fH.

24. Consider an active-loaded MOS differential amplifier of the type shown in the following figure. Assume that for all transistors, W/L = 7.2m/0.36m, Cgs = 20fF, Cgd = 5fF, and Cdb = 5fF. Also, let nCox = 387 A/V2, pCox = 86 A/V2, VAn = 5 V/m, |VAp| = 6 V/m. The bias current I = 0.2mA, and the bias current source has an output resistance RSS = 25k and an output capacitance CSS = 0.2pF. In addition to the capacitances introduced by the transistors at the output node, there is a capacitance Cx of 25fF. It is required to determine the low-frequency values of Ad, Acm, and CMRR. It is also required to find the poles and zero of Ad and the dominant pole of CMRR.

25. An amplifier has the voltage transfer function 10s T ( s) = (1 + s / 102 )(1 + s / 105 ) Find the poles and zeros and sketch the magnitude of the gain versus frequency. Find approximate values for the gain at =10, 103, and 106 rad/s. Find the Bode plot for the phase of the transfer function of the amplifier . 26. The noninverting op amp configuration shown in the figure provides a direct implementation of the feedback loop. (a) Assume that the op amp has infinite input resistance and zero output resistance. Find an expression for the feedback factor . (b) If the open-loop voltage gain A=104, find R2/R1 to obtain a closed-loop voltage gain Af of 10 (c) What is the amount of feedback in decibels? (d) If Vs = 1V, find Vo, Vf, and Vi. (e) If A decreases by 20%, what is the corresponding decrease in Af ?

27. The figure below shows an op amp connected in the noninverting configuration. The op amp has an openloop gain , a differential input resistance Rid, and an output resistance ro. Here we wish to use the feedback method to analyze the circuit taking both Rid and ro into account. Find expressions for A, , the closed-loop gain Vo/Vs, the input resistance Rin (see the figure), and the output resistance Rout. Also find numerical values, given = 104, Rid = 100k, ro = 1k, RL = 2k, R1 = 1k, R2 = 1M, and Rs= 10k.

28. Because negative feedback extends the amplifier bandwidth, it is commonly used in the design of broadband amplifiers. One such amplifier is the MC1553. Part of the circuit of the MC1553 is shown in the following figure. The circuit shown (called a feedback triple) is composed of three gain stages with series-series feedback provided by the network composed of RE1, RF, and RE2. Assume that the bias circuit, which is not shown, causes IC1 = 0.6mA, IC2 = 1mA, and IC3 = 4mA. Using these values and assuming hfe = 100 and ro = , find the open-loop gain A, the feedback factor , the closed loop gain Af = Io/Vs, the voltage gain Vo/Vs, the input resistance Rin = Rif, and the output resistance Rof (between nodes Y and Y, as indicated). Now if ro of Q3 is 25k, estimate an approximate value of the output resistance Rout.

29. We want to analyze the circuit of the figure below to determine the small-signal voltage gain Vo/Vs, the input resistance Rin, and the output resistance Rout = Rof. The transistor has = 100.

30. Use the feedback method to find the voltage gain Vo/Vs, the input resistance Rin, and the output resistance Rout of the inverting op amp configuration of the figure below. Let the op amp have open-loop gain = 104, Rid = 100k, and ro = 1k.

31. A 12-bit dual-slope ADC of the type illustrate in the figure below utilizes a 1-MHz clock and has VREF = 10V. Its analog input voltage is in the range 0 to -10V. The fixed interval T1 is the time taken for the counter to accumulate a count of 2N. What is the time required to convert an input voltage equal to the full-scale value? If the peak voltage reached at the output of the integrator is 10V, what is the integrator time constant? If through aging, R increase by 2% and C decreases by 1%, what does VPEAK become? Does the conversion accuracy change?

(a)
10

(b) The dual-slope A/D conversion method. Note that vA is assumed to be negative. 32. Consider the DAC circuit of the figure below for the cases N = 2, 4, and 8. What is the tolerance, expressed as x% , to which the resistors should be selected to limit the resulting output error to the equivalent of 1 2 LSB% .

An N-bit D/A converter using a binary-weighted resistive ladder network. 33. For a Flip-flop of the type shown in the figure below, determine the minimum width required of the set (S) and reset (R) pulse. Let M1~M4 be minimum-size devices for which W/L = 2m/1m and all other devices have W/L = 4m/1m. VDD = 5V, |VT| = 1V, kn = 2.5kp = 100 A/V2, and the total capacitance at each of nodes Q and Q is 30fF.

CMOS implementation of a clocked SR flip-flop.


11

34. In a particular 1G-bit memory of the dynamic type (called DRAM) under development by Samsung, using a 0.16 m, 2-V technology, the cell array occupies about 50% of the area of the 21 mm 31 mm chip. Estimate the cell area. If two cells form a square, estimate the cell dimensions. 35. For a particular DRAM design, the cell capacitance Cs = 50pF, VDD = 5V, and VT = 1.4V. Each cell represents a capacitive load on the bit line of 2-fF. The sense amplifier and other circuitry attached to the bit line has a 20-fF capacitance. What is the maximum number of cells that can be attached to a bit line while ensuring a minimum bit-line signal of 0.1V? How many bits of row addressing can be used? If the senseamplifier gain is increased by a factor of 5, how many word-line address bits can be accommodated? 36. Consider the write operation of the SRAM cell of the figure below. Specifically, refer to relevant parts of the circuit, as depicted in the figure. Let the process technology be characterized by n/p = 2.5, p Cox = 20 A/V2, |Vt0| = 0.8V, 2f = 0.6V, = 0.5V0.5, VDD = 5V. Also let each of the two inverters be matched and (W/L)1 = (W/L)3 = n, where n denoted the W/L ratio of a minimum-size device. (a) Using the circuit in Fig. (a), find the minimum required (W/L) of Q5 (in terms of n) so that node Q can be pulled to VDD/2, that is, at v Q = 2.5V, I5 = I1.
(b) Using the circuit of Fig. (b), find the minimum required (W/L) of Q6 (in terms of n) so that node Q can be pulled down to VDD/2, that is, at v Q = 2.5V, I6 = I4. (c) Since Q5 and Q6 are designed to have equal W/L ratios, which of the two values found in (a) and (b) would you choose for a conservative design? (d) For the value found in (c) and for n = 2, and nCox = 50A/V2, determine the time for vQ to reach VDD/2. Let CQ = 50fF.

CMOS SRAM Cell

Write Operation
12

37. Find the frequency of oscillation of the circuit shown in the figure below for the case R1 = 10K, R2 = 16K, C = 10nF, and R = 62K.

38. Consider the Pierce crystal oscillator of the figure below. The quartz crystal is specified to have L = 0.52H, Cs = 0.012pF, Cp = 4pF, and r = 120. Let C1 be variable in the range 1pF to 10pF, and Let C2 be fixed at 10pF. Find the range over which the oscillation frequency can be tuned.

Pierce crystal oscillator 39. Using a 680pF capacitor, design the astable circuit of the figure below to obtain a square wave with a 50kHz frequency and a 75% duty cycle. Specify the values of RA and RB.

13

An astable multivibrator implemented by the 555 timer. 40. Consider the operation of the differential sense amplifier of the figure below following the rise of the sense control signal s. Assume that a balanced differential signal of 0.1V is established between the bit lines each of which has a 1-pF capacitance. For VDD = 3V, what is the value of Gm of each of the inverters in the amplifier required to cause the outputs to reach 0.1 VDD and 0.9 VDD (from initial values of 0.5VDD + (0.1/2) and 0.5VDD (0.1/2) volts, respectively) in 2 ns? If for the matched inverters, |Vt| = 0.8V and kn = 3kp = 75 A/V2, what are the device widths required? If the input signal is 0.2V, what does the amplifier response time become?

14

A differential sense amplifier

15

You might also like