Scribd
Upload
1K views5 pages

Magnetostriction Effect

This document provides instructions for conducting an experiment to study magnetostriction in a metallic rod using a Michelson interferometer. The experiment involves applying different currents to a magnetostriction coil wrapped around the rod and counting the interference fringes that appear or disappear on a screen to calculate the change in length of the rod. Key steps include aligning the laser beam splitter and mirrors, applying current to the coil and recording the number of fringes, calculating the change in length using the fringe count and laser wavelength, and plotting graphs of change in length versus current.

Uploaded by

Julia Daniel
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
1K views5 pages

Magnetostriction Effect

This document provides instructions for conducting an experiment to study magnetostriction in a metallic rod using a Michelson interferometer. The experiment involves applying different currents to a magnetostriction coil wrapped around the rod and counting the interference fringes that appear or disappear on a screen to calculate the change in length of the rod. Key steps include aligning the laser beam splitter and mirrors, applying current to the coil and recording the number of fringes, calculating the change in length using the fringe count and laser wavelength, and plotting graphs of change in length versus current.

Uploaded by

Julia Daniel
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 5

1

(Lab Copy) Magnetostriction Experiment


Object: To study the Magnetostriction in metallic rod with the help of Michelson Interferometer. Apparatus Used: He-Ne Laser with adjustable stand, Magnetostriction set-up with mechanical and optical components to construct Michelson Interferometer, Magnetostriction coil, Constant current source, Screen, Post mount stand etc. Formula Used: A magnetostrictive coefficient is defined as the fractional change in length as magnetization increases from zero to its saturation value. Change in length l can be found by using following formula: l = n / 2 Where, l n Procedure: 1. Put the He-Ne Laser on stand at the fixed end side of the mini optical bench i.e. on right hand side of the set-up. Switch ON the laser. Align the laser such that the laser beam falls in the middle of lens L1 which spread out the beam. 2. Align the laser beam, beam splitter and mirror M 2 such that the spread laser beam from lens L1 fall on the beam splitter. 3. Adjust the beam splitter such that it reflect the 50% of the incident light to the mirror M2 which again reflected and relayed to the projection screen through beam splitter, while the other 50% part of the incident beam is transmitted through beam splitter and fall on mirror M1 which again reflected it and also proceed through beam splitter on the screen. Thus we get two luminous spot on the screen. Make them closer by adjusting Magnetostriction coil. Coincide these spots by adjusting the mirror M2 (by very slightly adjusting the screws provided at the back side of mirror M 2) until as slight flickering of the luminous spot can be seen on the screen. 4. Get the clear interference pattern on the screen by adjusting mirror M 1 and Magnetostriction coil with mirror M2. NOTE: The mirror M should be in the middle of the Magnetostriction coil. = change in length, = no. of fringes changes or band shift, = 6328 x 10-8 cm.

5. Connect the Magnetostriction coil with the constant current source and apply some current say 200 mA. The rings in the Interference pattern will appear. Note the total number of rings appearing for a definite time (say 5 minutes) corresponding to this coil current. Make table as shown below and record these readings in table. 6. Switch OFF the current source the interference ring will become start to disappear. Note the total number of rings disappearing for the definite time (same as it was in the case of counting rings appearing, say 5 minutes). Record these readings also in table. 7. Repeat the experiment for different value of coil current say 300 mA., 400 mA, 500 mA etc. 8. Calculate the change in length corresponding to different coil currents. Observations: Current I (mA) S.No. 1. 2. 3. . . . 200 300 400 . . . No. of rings appears (n1) No. of rings disappears (n1) Mean n = (n1 + n2)/2

Option: For any value of current say 200mA count the cumulative no. of rings appearing in the interval of 2 min and find l / l then plot a graph between l / l vs. time (min). Observation: Current I = . (mA) S.No. Time (min) 1. 2. . . . 2 4 . . . Cumulative no. of rings appearing (n) l (cm) l / l

3 Ray diagram: (Should be on left page by pencil)

Calculations: (Should be on left page by pen) (i) For Magnetostriction coil current, I = 300 mA The mean of no. of rings, Wavelength of laser light, n= = 6328 x 10 -8 cm

Therefore, the change in length, l = n / 2 (Putting all proper values from above, we can calculate the change in length) (ii) Similarly we can calculate l for other value of coil current

4 Results: The change in length for different coil currents due to positive Magnetostriction effect in Fe rod is shown in table.

S.No. 1. 2. 3. . . .

Magnetostriction Coil Current I (mA) 200 300 400 . . .

Change in length l (in mm)

Option: Calculate (l / l) for each value of current and plot a graph for current I (mA) or magnetic field vs. (l / l) (mm) Maximum Probable Error: (Should be on left page by pen) l = n / 2 Taking log of both sides and differentiates (l)/ l = ? Sources of error and precautions: (i) Alignment of set up should not be disturbed during this experiment. (ii) Dont see the laser source directly.

5 (iii) He-Ne laser should fall normal on lens L1. (iv) Count the no. of rings appearing and disappearing accurately.

You might also like