COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
By
Dr.Abdul-Mohsen Al-Hammad
OUTLINE
INTRODUCTION THE SYSTEMATIC APPROACH FOR THE DIAGNOSIS OF A BUILDING DEFECT CAUSES OF DETERIORATION IN BUILDINGS IN GENERAL DETAILED CAUSES OF DETERIORATIN IN BUILDINGS WITH EXAMPLES
COLLEGE OF ENVIRONMENTAL DESIGN
INTRODUCTION
Proper building maintenance should be considered during:
COLLEGE OF ENVIRONMENTAL DESIGN
* Planning * Design * Construction, and * Maintenance stages During maintenance stage, effective building maintenance requires: The correct diagnosis of defect, and implementation of the correct remedial measures all based on sound technical knowledge, otherwise waste of capital resources have to be done again.
REPAIRS WITHOUT DIAGNOSES
COLLEGE OF ENVIRONMENTAL DESIGN
THE SYSTEMATIC APPROACH FOR THE DIAGNOSIS OF A BUILDING DEFECT 1/2
COLLEGE OF ENVIRONMENTAL DESIGN
1. 2.
Problem Definition Field Survey and Inspection a. Visual Inspection, includes: Taken Photos Looking for similar defect in the same area
b.
Field Measurement, includes: Written record about the sizes and dimensions of the defect Samples of the defected material and its adjacent area are taken
THE SYSTEMATIC APPROACH FOR THE DIAGNOSIS OF A BUILDING DEFECT 2/2 3. Laboratory Testing of Field Samples Requires Test for: Strength Chemical and physical properties of the field samples Other tests relevant to the defect condition 4. Examine the AS-Built Design Drawings Obtain information relevant to the defect area 5. Analysis and Discussion Compare the Lab. And field study results with the information obtained from the As-built drawings then after that, 6. Conclusion can be withdrawn
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS IN GENERAL
COLLEGE OF ENVIRONMENTAL DESIGN
The primary source and causes of deterioration and decay in structures and buildings can be listed as follows: 1.Human 2.Chemical 3. Atmospheric 4.Structural 5. Moisture 6.Fire 7.Faulty Design 8. Faulty Construction 9. Faulty Materials 10. Faulty System 11. Faulty Systems 12. Cleaning 13. Vandalism
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
1. HUMAN
1.
COLLEGE OF ENVIRONMENTAL DESIGN
Human
Failure to clean and carry out routine maintenance Ignorance of the causes of deterioration and decay Poor planning for proper maintenance Failure to promote awareness of maintenance needs by all who use the buildings. Adopting a negative attitude of waiting until emergency measures are required.
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
2.CHEMICAL
2.
COLLEGE OF ENVIRONMENTAL DESIGN
Chemical
- Interaction of certain cleaning agents with materials and/or components causing disintegration, softening or discoloration. - Promoting Corrosion - Interaction of certain dissimilar materials in close contact with one another in a corrosion environment.
2.CHEMICAL-1-Discoloration-Concrete ages
COLLEGE OF ENVIRONMENTAL DESIGN
2.CHEMICAL 3-Alkali Aggregate Reaction
COLLEGE OF ENVIRONMENTAL DESIGN
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
3.ATMOSPHERIC
3.
COLLEGE OF ENVIRONMENTAL DESIGN
Atmospheric
- Reaction of the structure, external fabric, finishes and claddings to the atmospheric elements such as: Wind Rain Sun Frost and snow for cold weather Pollution in the atmosphere - Reaction of the building to the penetration of the above atmospheric elements.
3-ATMOSPHERIC 1.D-Cracking frost cycles
COLLEGE OF ENVIRONMENTAL DESIGN
3-ATMOSPHERIC 2-Climate
COLLEGE OF ENVIRONMENTAL DESIGN
3-ATMOSPHERIC 3-Clay Brickwork frost
cycles-Salt reaction
COLLEGE OF ENVIRONMENTAL DESIGN
3-ATMOSPHERIC 4-Clay Natural Stone
frost cycles-Salt reaction-pollution
COLLEGE OF ENVIRONMENTAL DESIGN
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
4.STRUCTURAL
4.
COLLEGE OF ENVIRONMENTAL DESIGN
Structural
- Reaction of the structural elements to settlement, moisture, shrinkage and thermal movements. - Reaction of the structural elements to the change of loading patterns. - Natural aging of the structural elements - Reaction to the corrosive elements in the atmosphere - Deterioration due to inadequate inspecting and maintenance
4.STRUCTURAL 1.Cracks Typesin brick and block work
COLLEGE OF ENVIRONMENTAL DESIGN
4.STRUCTURAL 2.Internal wall
settlement of the floor
COLLEGE OF ENVIRONMENTAL DESIGN
4.STRUCTURAL 3-External wallDiagonal CracksCOLLEGE OF ENVIRONMENTAL DESIGN
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
5.MOISTURE
5.
COLLEGE OF ENVIRONMENTAL DESIGN
Moisture
- Penetration of the external fabric of claddings, or through ground floor constructions giving to dampness which may create a suitable condition for fungi growth and attack. - Excessive moisture in the internal atmosphere which may lead to excessive condensation and corrosion. - Irrigation - Faculty Plumbing
5.MOISTURE 1-Dampness on CeilingsRoof leaksCOLLEGE OF ENVIRONMENTAL DESIGN
5.MOISTURE 2-EfflorescenceLeaks through cracksCOLLEGE OF ENVIRONMENTAL DESIGN
5.MOISTURE 3-External FinishingPlastering on under burnt bricksCOLLEGE OF ENVIRONMENTAL DESIGN
5.MOISTURE 4-External Finishingpresence of moisture in betweenCOLLEGE OF ENVIRONMENTAL DESIGN
5.MOISTURE 5-External Finishingpresence of moisture in betweenCOLLEGE OF ENVIRONMENTAL DESIGN
5.MOISTURE 6-External Finishingpresence of moisture in betweenCOLLEGE OF ENVIRONMENTAL DESIGN
5.MOISTURE 7-External FinishingLeaks of plumbing in bathroomsCOLLEGE OF ENVIRONMENTAL DESIGN
5.MOISTURE 8-External FinishingLeaks of plumbing in bathrooms-Enlarged
COLLEGE OF ENVIRONMENTAL DESIGN
5.MOISTURE 9-External FinishingIrrigation
COLLEGE OF ENVIRONMENTAL DESIGN
5.MOISTURE 10-External FinishingIrrigation
COLLEGE OF ENVIRONMENTAL DESIGN
5.MOISTURE 11-External FinishingIrrigation COLLEGE OF ENVIRONMENTAL DESIGN
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
6. FIRE
6.
COLLEGE OF ENVIRONMENTAL DESIGN
Fire
- Aftermath of a fire many possibilities may occur. - Need for replacement of materials directly effected by the fire - Damage can be done by the fire fighters in their efforts to control the fire - Water used during the fire fighting can not only damage but also set up deteriorating in materials not directly involved. - The heat and the combination of heat and water can lead to the swelling, distortion, spilling and cracking of nearby materials and components.
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
7.FAULTY DESIGN
7.
COLLEGE OF ENVIRONMENTAL DESIGN
Faulty Design
- Poor detailing at the design stage including: - Insufficient allowance for expansion or contraction - Absence of weathering - Incorrectly placed damp proof courses - Poor jointing between different materials or components - Poor specification - Lack of adequate consideration of future maintenance problems - Inadequate provisions for access to carry out maintenance activities.
7.FAULTY DESIGN 1-Wall cracksPoor detailing-strong bond vertical crackCOLLEGE OF ENVIRONMENTAL DESIGN
7.FAULTY DESIGN 2-Wall cracksPoor detailing-weak bond diagonal stepped crackCOLLEGE OF ENVIRONMENTAL DESIGN
7.FAULTY DESIGN 3-Wall cracksVertical crack-cavity clay brick work-restrained by columns
COLLEGE OF ENVIRONMENTAL DESIGN
7.FAULTY DESIGN 4-Wall cracksPoor detailing-Parapets cracking-Extreme weather
COLLEGE OF ENVIRONMENTAL DESIGN
7.FAULTY DESIGN 5-Wall cracksPoor detailing-Diagonal crack-Expansion and shrinkage
COLLEGE OF ENVIRONMENTAL DESIGN
7.FAULTY DESIGN 6-Clay tilesPoor detailing-No allowance for E&CCOLLEGE OF ENVIRONMENTAL DESIGN
7.FAULTY DESIGN 7-External wall Poor detailing-Spilling of brickwork cladding-compression of the
concrete wall
COLLEGE OF ENVIRONMENTAL DESIGN
7.FAULTY DESIGN 8-Slab with WallsPoor detailing-Random cracks near wallsCOLLEGE OF ENVIRONMENTAL DESIGN
7.FAULTY DESIGN 9-Wall cracksPoor detailing-Horizontal cracks -No allowance for E&CCOLLEGE OF ENVIRONMENTAL DESIGN
7.FAULTY DESIGN 10-Plumbing designDirect to the wallCOLLEGE OF ENVIRONMENTAL DESIGN
7.FAULTY DESIGN 11-A/C unit on the roofWithout proper design for drainageCOLLEGE OF ENVIRONMENTAL DESIGN
7.FAULTY DESIGN 12-A/C unit on the roofWithout proper design for drainage- COLLEGE OF ENVIRONMENTAL DESIGN
7.FAULTY DESIGN 13-A/C unit on the roofWithout proper design for drainageCOLLEGE OF ENVIRONMENTAL DESIGN
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
8.FAULTY CONSTRUCTION
8.
COLLEGE OF ENVIRONMENTAL DESIGN
Faulty Construction
- Lack of supervision during construction period - Failure to understand or follow exactly the specification and/or drawings - Failure to replace defective work - Failure of Designer/Architect/or Engineer monitor works in progress - Lack of skilled labor - Over emphasis or need for quantity rather than quality - Failure to fully appreciate the consequences of shady or poor and/or materials
8.FAULTY CONSTRUCTION 1-CrazingA pattern of fine shallow random cracks-Spreading
COLLEGE OF ENVIRONMENTAL DESIGN
dry cement on concrete or wetting dry concrete for finishing
8.FAULTY CONSTRUCTION 2-CrazingEnlarged-Spreading dry cement on concrete or wetting dry
concrete for finishing
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION 3-Plastic CrackingOccurs while concrete in plastic state-rapid loss of water or settlement of aggregates
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -4-Plastic CrackingEnlarged-rapid loss of water or settlement of aggregates
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -5-Honey combingImproper consolidation of concrete by vibration
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -6-Honey combingImproper consolidation of concrete by vibration
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -7-Honey combingSand streak-loss of cement grout from the form
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -8-Sticking to forms
Damage caused during stripping of formwork from concrete
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -9-Cold joints
Due to pouring concrete in different times
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -10-Floors tiles
Workmanship-base concrete-grading of aggregate
COLLEGE OF ENVIRONMENTAL DESIGN
8 8.FAULTY CONSTRUCTION -11-Floors tiles
Workmanship-base concrete-grading of aggregate
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -12-Corrosion
Workmanship-inadequate concrete cover
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -13-Corrosion
Workmanship-inadequate concrete cover
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -14-Corrosion
Workmanship-inadequate concrete cover
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -15-Corrosion
Workmanship-inadequate concrete cover
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -16-Plasterwork
Workmanship-plasterwork on dense concrete
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -17-External Finishing
Workmanship-Cracking of the base wall or shrinkage of the plaster
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -18-External Finishing
Workmanship-Cracking of the base wall or shrinkage of the plaster
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -19-Internal Finishing
Workmanship-Ceramic tiles, loss of adhesion-inadequate space fixing
COLLEGE OF ENVIRONMENTAL DESIGN
8.FAULTY CONSTRUCTION -20-Roofs Blistering
occurs between layers of felts due to water vapor underneath
COLLEGE OF ENVIRONMENTAL DESIGN
7/8.FAULTY DESIGN/CONSTRUCTION 1-Floor
deflection :Cracks at the wall bottom due to floor deflection
COLLEGE OF ENVIRONMENTAL DESIGN
7/8.FAULTY DESIGN/CONSTRUCTION 2-Internal
Finishing :plaster Cracks due to shrinkage-base wall movementuse of different materials
COLLEGE OF ENVIRONMENTAL DESIGN
7/8.FAULTY DESIGN/CONSTRUCTION 3-Internal
wall finishing:Blistering due to dampness-chemical-water vapor
COLLEGE OF ENVIRONMENTAL DESIGN
7/8.FAULTY DESIGN/CONSTRUCTION 4-Ceiling
Finishing: Flaking-dampness-chemical-incompatibility of the paint
with that of the ceiling
COLLEGE OF ENVIRONMENTAL DESIGN
7/8.FAULTY DESIGN/CONSTRUCTION 5-Plumbing
leaks at joints: Due to use of different metalsexpansion from hot water
COLLEGE OF ENVIRONMENTAL DESIGN
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
9.FAULTY MATERIALS and 10.FAULTY COMPONENTS
9.
COLLEGE OF ENVIRONMENTAL DESIGN
Faulty Materials
- Failure of client, builder, designer or architect to reject sub-standard materials. - In adequate inspection of materials by supplier or receiver - Inadequate storage facilities on site - Inadequate/or inconsistent mixing of materials on site
10. Faulty Components
Similar condition to those given above for faulty material can lead to deterioration and decay of the fabric, services or finishes of the structure of building.
9.FAULTY MATERIALS -1-Popouts
Due to expansion of soft aggregate or present of glass in the aggregate
COLLEGE OF ENVIRONMENTAL DESIGN
9.FAULTY MATERIALS -2-Popouts
Due to expansion of soft aggregate or present of glass in the aggregate
COLLEGE OF ENVIRONMENTAL DESIGN
10.FAULTY COMPONENTS -1-Services
Failure of insulation-Overheating/overload
COLLEGE OF ENVIRONMENTAL DESIGN
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
11.FAULTY SYSTEMS
11. Faculty Systems
COLLEGE OF ENVIRONMENTAL DESIGN
- Inadequate knowledge on the part of the designer or architect leading to an unsatisfactory design, detail of system. - Inability of the installer to follow the specification and/or drawings - Inadequate testing of the system before commissioned - Failure of owner to follow maintenance instructions provided by manufacturer or designer. - Inability of the owner to operate the system as instructed.
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
12.CLEANING
12. Cleaning
COLLEGE OF ENVIRONMENTAL DESIGN
- Failure to carry out routing cleaning operations - Use of incorrect cleaning materials and/or techniques - Inadequate supervision of cleaners to ensure that cleaning is thorough - Failure of owner to tenant to provide sufficient space, enough time or the correct equipment and materials for cleaning operations - Failure to employ specialists for cleaning special fittings and equipment.
12. CLEANING -1-Cleaning
Use of unsuitable detergent
COLLEGE OF ENVIRONMENTAL DESIGN
COLLEGE OF ENVIRONMENTAL DESIGN
CAUSES OF DETERIORATION IN BUILDINGS
13.VANDALISIM
13. Vandalism
COLLEGE OF ENVIRONMENTAL DESIGN COLLEGE OF ENVIRONMENTAL DESIGN
- Lack of security - Failure to promote awareness among occupants of the consequences of vandalism - Incorrect selection of materials and finishes in circulation areas which are prone to vandalism - Failure to maintain or repair areas of damage by vandals thus encouraging more vandalism.
Conclusion
It is impossible to control all the above factors during design, construction and occupations stages of buildings. However, considering these factors and minimizing their effect will definitely reduce the amount and need for maintenance.
