60 Hz Curves

Model 3196

2X3-6

2X3-6

2X3-6

2X3-6

1 X 1.5 - 8

1 X 1.5 - 8
34

CHEM-1A

50 Hz Curves

Model 3171

4X4-8

4X4-8

1.5 X 2 - 11

1.5 X 2 - 11

2.5 X 3 - 11
295

3 X 4 - 11

CHEM-4A

50 Hz Curves

Model 3700

4 X 6 - 13H

4 X 6 - 13L

4 X 6 - 13L

4 X 6 - 13L

4 X 6 - 13N
577

4 X 6 - 13N

API-1A

1 0 T e c h n i c a l
D a t a

VELOCITY HEAD (hv) is the energy of a liquid as a result of its motion at some velocity V. It is the equivalent head in feet through which the water would have to fall to acquire the same velocity, or in other words, the head necessary to accelerate the water. Velocity head can be calculated from the following formula:
2 hv = V 2g 2 where g = 32.2 ft/sec. V = liquid velocity in feet per second

TOTAL DYNAMIC SUCTION LIFT (hs) is the static suction lift minus the velocity head at the pump suction flange plus the total friction head in the suction line. The total dynamic suction lift, as determined on pump test, is the reading of a gauge on the suction flange, converted to feet of liquid and corrected to the pump centerline, minus the velocity head at the point of gauge attachment.

PRESSURE HEAD must be considered when a pumping system either begins or terminates in a tank which is under some pressure other than atmospheric. The pressure in such a tank must first be converted to feet of liquid. A vacuum in the suction tank or a positive pressure in the discharge tank must be added to the system head, whereas a positive pressure in the suction tank or vacuum in the discharge tank would be subtracted. The following is a handy formula for converting inches of mercury vacuum into feet of liquid. Vacuum, ft. of liquid = Vacuum, in. of Hg x 1.13 Sp. Gr.

The velocity head is usually insignificant and can be ignored in most high head systems. However, it can be a large factor and must be considered in low head systems.

TOTAL HEAD (H) or TOTAL Dynamic HEAD (TDH) is the total dynamic discharge head minus the total dynamic suction head or plus the total dynamic suction lift. TDH = hd + hs (with a suction lift) TDH = hd hs (with a suction head)

TOTAL DYNAMIC DISCHARGE HEAD (hd) is the static discharge head plus the velocity head at the pump discharge flange plus the total friction head in the discharge line. The total dynamic discharge head, as determined on pump test, is the reading of a gauge at the discharge flange, converted to feet of liquid and corrected to the pump centerline, plus the velocity head at the point of gauge attachment.

TOTAL DYNAMIC SUCTION HEAD (hs) is the static suction head plus the velocity head at the pump suction flange minus the total friction head in the suction line. The total dynamic suction head, as determined on pump test, is the reading of the gauge on the suction flange, converted to feet of liquid and corrected to the pump centerline, plus the velocity head at the point of gauge attachment.

TECH-A-2 Capacity

The above forms of head, namely static, friction, velocity, and pressure, are combined to make up the total system head at any particular flow rate. Following are definitions of these combined or Dynamic head terms as they apply to the pump.

Capacity (Q) is normally expressed in gallons per minute (gpm). Since liquids are essentially incompressible, there is a direct relationship between the capacity, or flow rate, and the pipe sze and fluid velocity. This relationship is as follows: Q = V x (ID2) x 2.445

Where

ID = inside diameter of the pipe, inches Q = capacity, gallons per minute

V = Velocity of the liquid, feet per second

STATIC DISCHG HEAD TOTAL STATIC HEAD

STATIC SUCTION LIFT

Fig. 2-a Suction Lift Showing Static Heads in a Pumping System Where the Pump is Located Above the Suction Tank. (Static Suction Head)

TECH-A

1102

TECH-A-4 Specific Speed and Pump Type

Specific speed (Ns) is a non-dimensional design index used to classify pump impellers as to their type and proportions. It is defined as the speed in revolutions per minute at which a geometrically similar impeller would operate if it were of such a size as to deliver one gallon per minute against one foot head. The understanding of this definition is of design engineering significance only, however, and specific speed should be thought of only as an index used to predict certain pump characteristics. The following formula is used to determine specific speed:

The specific speed determines the general shape or class of the impeller as depicted in Fig. 3. As the specific speed increases, the ratio of the impeller outlet diameter, D2, to the inlet or eye diameter, D1, decreases. This ratio becomes 1.0 for a true axial flow impeller.

Where N = Pump speed in RPM Q = Capacity in gpm at the best efficiency point H = Total head per stage at the best efficiency point

Ns = N Q H3/4

Radial flow impellers develop head principally through centrifugal force. Pumps of higher specific speeds develop head partly by centrifugal force and partly by axial force. A higher specific speed indicates a pump design with head generation more by axial forces and less by centrifugal forces. An axial flow or propeller pump with a specific speed of 10,000 or greater generates its head exclusively through axial forces. Radial impellers are generally low flow high head designs whereas axial flow impellers are high flow low head designs.

Values of Specific Speed, Ns

TECH-A-5 Net Positive Suction Head (NPSH) and Cavitation

The Hydraulic Institute defines NPSH as the total suction head in feet absolute, determined at the suction nozzle and corrected to datum, less the vapor pressure of the liquid in feet absolute. Simply stated, it is an analysis of energy conditions on the suction side of a pump to determine if the liquid will vaporize at the lowest pressure point in the pump. The pressure which a liquid exerts on its surroundings is dependent upon its temperature. This pressure, called vapor pressure, is a unique characteristic of every fluid and increases with increasing temperature. When the vapor pressure within the fluid reaches the pressure of the surrounding medium, the fluid begins to vaporize or boil. The temperature at which this vaporization occurs will decrease as the pressure of the surrounding medium decreases. A liquid increases greatly in volume when it vaporizes. One cubic foot of water at room temperature becomes 1700 cu. ft. of vapor at the same temperature.

Fig. 3 Impeller Design vs Specific Speed

It is obvious from the above that if we are to pump a fluid effectively, we must keep it in liquid form. NPSH is simply a measure of the amount of suction head present to prevent this excess vaporization at the lowest pressure point in the pump.

NPSH Required is a function of the pump design. As the liquid passes from the pump suction to the eye of the impeller, the velocity increases and the pressure decreases. There are also pressure losses due to shock and turbulence as the liquid strikes the impeller. The centrifugal force of the impeller vanes further increases the velocity and decreases the pressure of the liquid. The NPSH Required is the positive head in feet absolute required at the pump suction to overcome these pressure drops in the pump and maintain enough of the liquid above its vapor pressure to limit the head loss, due to the blockage of the cavitation vapor bubble, to 3 percent. The 3% head drop criteria for NPSH Required is used worldwide and is based on the ease of determining the exact head drop off point. Most standard low suction energy pumps can operate with little or no margin above the NPSH Required, without seriously affecting the service life of the pump. The NPSH Required varies with speed and capacity within any particular pump. Pump manufacturers curves normally provide this information.

TECH-A

1104

NPSH Available is a function of the system in which the pump operates. It is the excess pressure of the liquid in feet absolute over its vapor pressure as it arrives at the pump suction. Fig. 4 shows four typical suction systems with the NPSH Available formulas applicable to each. It is important to correct for the specific gravity of the liquid and to convert all terms to units of feet absolute in using the formulas.

4a SUCTION SUPPLY OPEN TO ATMOSPHERE - with Suction Lift

4b SUCTION SUPPLY OPEN TO ATMOSPHERE - with Suction Head

4c CLOSED SUCTION SUPPLY - with Suction Lift

4d CLOSED SUCTION SUPPLY - with Suction Head

VP = Vapor pressure of the liquid at maximum pumping temperature, in feet absolute. p

PB = Barometric pressure, in feet absolute.

LH = Minimum static suction head in feet. hf

Ls

= Maximum static suction lift in feet.

= Pressure on surface of liquid in closed suction tank, in feet absolute.

= Friction loss in feet in suction pipe at required capacity

Fig. 4 Calculation of system Net Positive Suction Head Available for typical suction conditions.

1105

TECH-A

In an existing system, the NPSH Available can be determined by a gauge on the pump suction. The following formula applies: NPSHA= PB Vp Gr + hv Where Gr = Gauge reading at the pump suction expressed in feet (plus if above atmospheric, minus if below atmospheric) corrected to the pump centerline.

pockets of fatigue failure on the impeller vane surfaces. This action may be progressive, and under severe (very high suction energy) conditions can cause serious pitting damage to the impeller.

Cavitation is a term used to describe the phenomenon, which occurs in a pump when there is insufficient NPSH Available. The pressure of the liquid is reduced to a value equal to or below its vapor pressure and small vapor bubbles or pockets begin to form. As these vapor bubbles move along the impeller vanes to a higher pressure area, they rapidly collapse. The collapse, or implosion, is so rapid that it may be heard as a rumbling noise, as if you were pumping gravel. In high suction energy pumps, the collapses are generally high enough to cause minute

hv = Velocity head in the suction pipe at the gauge connection, expressed in feet.

The accompanying noise is the easiest way to recognize cavitation. Besides possible impeller damage, excessive cavitation results in reduced capacity due to the vapor present in the pump. Also, the head may be reduced and/or be unstable and the power consumption may be erratic. Vibration and mechanical damage such as bearing failure can also occur as a result of operating in excessive cavitation, with high and very high suction energy pumps. The way to prevent the undesirable effects of cavitation in standard low suction energy pumps is to insure that the NPSH Available in the system is greater than the NPSH Required by the pump. High suction energy pumps require an additional NPSH margin, above the NPSH Required. Hydraulic Institute Standard (ANSI/HI 9.6.1) suggests NPSH margin ratios of from 1.2 to 2.5 times the NPSH Required, for high and very high suction energy pumps, when operating in the allowable operating range.

TECH-A-6 NPSH Suction Specific Speed and Suction Energy

In designing a pumping system, it is essential to provide adequate NPSH available for proper pump operation. Insufficient NPSH available may seriously restrict pump selection, or even force an expensive system redesign. On the other hand, providing excessive NPSH available may needlessly increase system cost. Suction specific speed may provide help in this situation. Suction specific speed (S) is defined as:
1/2 S = N (GPM) (NPSHR ) 3/4 1/2 9000 = N (2000) 30 3/4 1/2 S = N (GPM) (NPSH) 3/4

Running a pump at this speed would require a gear and, at this speed, the pump might not develop the required head. At a minimum, existing NPSHA is constraining pump selection. Same system as 1. Is a double suction pump practical? For a double suction pump, flow is divided by two.
1/2 9000 = N (1000) (30 )3/4 1/2 S = N (GPM) (NPSH) 3/4

N = 2580 RPM

Where

N GPM

= Pump speed RPM

= Pump flow at best efficiency point at impeller inlet (for double suction impellers divide total pump flow by two).

NPSH

= Pump NPSH required at best efficiency point.

For a given pump, the suction specific speed is generally a constant - it does not change when the pump speed is changed. Experience has shown that 9000 is a reasonable value of suction specific speed. Pumps with a minimum suction specific speed of 9000 are readily available, and are not normally subject to severe operating restrictions. An example: Flow 2,000 GPM; head 600 ft. What NPSH will be required? Assume: at 600 ft., 3550 RPM operation will be required.
1/2 S = N (GPM) (NPSHR ) 3/4

Using a double suction pump is one way of meeting system NPSH.

N = 3700 RPM

The amount of energy in a pumped fluid, that flashes into vapor and then collapses back to a liquid in the higher pressure area of the impeller inlet, determines the extent of the noise and/or damage from cavitation. Suction Energy is defined as: Suction Energy = De x N x S x Sg Where De Sg = Impeller eye diameter (inches)

1/2 9000 = 3550 (2000) (NPSHR ) 3/4

NPSH R 3/4 = 17.7 NPSH R = 46 ft.

High Suction Energy starts at 160 x 106 for end suction pumps and 120 x 106 for horizontal split case pumps. Very high suction energy starts at 1.5 times the High Suction Energy values. For estimating purposes you can normally assume that the impeller eye diameter is approximately 90% of the suction nozzle size, for an end suction pump, and 75% of the suction size for a double suction split case pump. An example: Suction specific speed 9,000, pump speed 3550 RPM, suction nozzle size 6 inch, specific gravity 1.0, and the pump type is end suction. De .9 x 6" = 5.4" Suction Energy = De x N x S x Sg = 5.4 x 3550 x 9,000 x 1.0 = 173 x 106

= Specific gravity of liquid (Sg - 1.0 for cold water)

Existing system: Flow 2000 GPM; head 600 ft.: NPSHA 30 ft. What is the maximum speed at which a pump can be run without exceeding NPSH available?

A related problem is in selecting a new pump, especially at higher flow, for an existing system. Suction specific speed will highlight applications where NPSHA may restrict pump selection. An example:

Since 173 x 106 > 160 x 106, this is a High Suction Energy pump.

TECH-A

1106

TECH-A-7 Centrifugal Pump Operation without NPSH Problems

Centrifugal Value with Centrifugal Pumps
General
(previously

There are many detailed publications on the subject of the NPSH value. In practice, however, mistakes are made repeatedly, with pump damage or even complete system failure as a result.

NPSHavail.)

NPSHA in m

Net positive suction headavail. in bar Gauge pressure in suction nozzle directly upstream the pump (in case of underpressure, this value is used with a negative = sign). in bar in bar abs Air pressure (normally 1.013 bar abs).

(previously ) s

This guideline is therefore intended to indicate where and how the system NPSH value can be rendered more favorable using various parameters, and the criteria which are important for pump selection. NPSH means Net Positive Suction Head. A system from which, for instance, cold water flows to a pump from a height of 1 m without a pressure drop has an NPSH value of aprox 11 m (not 1m). Here, only one pump with an NPSHR value of 10.5 m or less can normally be used, in order that a safety margin of at least 0.5 m is available. NPSHR = 10.5 m R = required NPSH = 11 m A = available

(previously ) B

amb

(previously ) D

in bar abs Vapor pressure of the fluid at working temperature. in kg/dm3 Density of the fluid at working temperature.

V1

(previously V ) S

in m/s Velocity of fluid conveyed in the suction nozzle.

NPSHA Value of the System

Here, a customary formula which is fully adequate for practice is provided. The latest symbols in accordance with DIN 24 260 Part 1, September 1986 edition, are used here. NPSHA = 10 (1 + amb - v) + v12

This data is referred directly to the center point of the suction nozzle. For the sake of simplicity, gravitational acceleration has been assumed not at 9.81 m/s2 but instead at 10.0 m/s2.

10

Example 1

1107

TECH-A

Suggestions for Remedies for NPSH Problems

NPSHR Value of the Pump This value can be roughly calculated, but is generally determined on a test rig, at a specified speed, a defined impeller diameter and a defined delivery rate. The NPSHR value is determined by ascertaining the total delivery head of the pump at various suction heads. In order to obtain various suction heads, the pressure in the suction reservoir is lowered by means of a throttling device. Combinations of these methods are frequently used in order to achieve the required vacuum. The greater the vacuum on the impeller inlet becomes, the more cavitation occurs. This impairs the pumps delivery head. The value at which the pumps total delivery head drops by 3% as a result of such cavitation is now stated as the NPSHR value. Several tests at the same delivery rate and differing pressure in the suction nozzle are necessary, until by means of repeated measurement/calculation, etc., a total delivery head drip of 3% has been ascertained. For determination of an NPSHR curve, these measurements are performed at various flows and at various impeller diameters. The compilation of such a series of curves requires high expenditures.

NPSHA<NPSHR - What can be done? 1

Referring to the system, the individual formula values can be adhered to. Increase pressure at the suction nozzle, i.e. feed more fluid, which is to say, raise the fluid level in the feed reservoir, raise the intake reservoir to a higher level or lower the pump, e.g., one floor down. On the other hand, the nominal diameter of the suction line should be adequately dimensioned, and it should be ensured that the valves/fittings in the suction line have the minimum possible friction loss coefficient in order that 1 is as high as possible at the pump. Ball valves with a fully open cross-section, for instance, are particularly suitable. No opportunities for change. In few cases, the fluid can be cooled before its entry to the pump, in order to reduce vapor pressure. Since this value accords with that of the pumps suction nozzle, it is of no significance for this observation. V1 should, naturally, be as small as possible, as already mentioned with respect to v. No opportunities for change.

amb v

V1

Example 2

TECH-A

1108

The following remedies can be applied to the pump: Reduce delivery rate Install larger impeller

Miscellaneous

The NPSHR value will generally become smaller, and the NPSHA value greater. If necessary, split delivery to several pumps, e.g., operate standby pump as well.

Plastic pumps are, generally, relatively insensitive to cavitation. It is also difficult to hear this phenomenon, since plastic is a good sound insulator.

Reduce speed Install larger impeller and reduce speed

In many cases, the NPSHR is better, but power consumption is, of course, also greater.

Pumps running at lower speeds have better NPSHR values. In many cases, however, a larger pump also becomes necessary. If a relatively small impeller is installed in the pump, this solution is ideal from a hydraulic viewpoint (smoother running, less wear).

Magnetic pumps can be treated like pumps with single mechanical seals. The temperature of the fluid should be at least 20C below its boiling point. The Influence of Vapor Pressure In this context, the significance of vapor pressure on the reliable operation of the pump should again be emphasized:

Operate pump with cavitation

Select pump with better NPSH value

In individual cases, the pump supplier and the operator of the system can agree, that total delivery head drip should be not 3%, but more. This must be determined carefully, however, in order that delivery does not collapse completely. Larger pumps in many cases have better NPSH values at the same delivery rate. If necessary, special impellers designed specifically for good suction can be installed.

Vapor pressure is a function of temperature. Fluids which are pumped close to vapor pressure are a particular hazard, since even slight increases in temperature can cause evaporation. Not only the temperature fluctuations in general, but also obstructed cooling or an uncontrolled input of heat can trip this off. Inadequate heat dissipation can, for instance, be due to an excessively low delivery rate. Heat input may occur due to increased friction in a mechanical seal, increased bearing friction in magnetic pumps, and also particularly due to heat losses (eddy currents) in metal cans on sealless pumps. Pumps with double mechanical seals are the least susceptible, since the contact surfaces are lubricated by a separate circuit. Reference: - Centrifugal pumps and centrifugal pump systems, DIN 24 260 Part 1 - NPSH in centrifugal pumps, Europump, 1981 edition

1109

TECH-A

TECH-A-8 Pump Characteristic Curves

The performance of a centrifugal pump can be shown graphically on a characteristic curve. A typical characteristic curve shows the total dynamic head, brake horsepower, efficiency, and net positive suction head all plotted over the capacity range of the pump. Figures 5, 6, & 7 are non-dimensional curves which indicate the general shape of the characteristic curves for the various types of pumps. They show the head, brake horsepower, and efficiency plotted as a percent of their values at the design or best efficiency point of the pump. Fig. 5 shows that the head curve for a radial flow pump is relatively flat and that the head decreases gradually as the flow increases. Note that the brake horsepower increases gradually over the flow range with the maximum normally at the point of maximum flow.

pump. The shut-off head is usually 150% to 200% of the design head. The brake horsepower remains fairly constant over the flow range. For a typical axial flow pump, the head and brake horsepower both increase drastically near shutoff as shown in Fig. 7. The distinction between the above three classes is not absolute, and there are many pumps with characteristics falling somewhere between the three. For instance, the Francis vane impeller would have a characteristic between the radial and mixed flow classes. Most turbine pumps are also in this same range depending upon their specific speeds.

Mixed flow centrifugal pumps and axial flow or propeller pumps have considerably different characteristics as shown in Figs. 6 and 7. The head curve for a mixed flow pump is steeper than for a radial flow

Fig. 8 shows a typical pump curve as furnished by a manufacturer. It is a composite curve which tells at a glance what the pump will do at a given speed with various impeller diameters from maximum to minimum. Constant horsepower, efficiency, and NPSHR lines are superimposed over the various head curves. It is made up from individual test curves at various diameters.

Fig. 5 Radial Flow Pump

Fig. 6 Mixed Flow Pump

TECH-A

1110

Fig. 7 Axial Flow Pump

Fig. 8 Composite Performance Curve

1111

TECH-A

TECH-A-9 Affinity Laws

1. With impeller diameter, D, held constant: A. Q1 N = 1 Q2 N2 Where: Q H BHP N

The affinity laws express the mathematical relationship between the several variables involved in pump performance. They apply to all types of centrifugal and axial flow pumps. They are as follows: = = = = Capacity, GPM Total Head, Feet Brake Horsepower Pump Speed, RPM

EXAMPLE:

B.

H1 N1 = H2 N2

( )

C.

BHP1 N1 = BHP2 N2

( )

The affinity laws listed under 1 above will be used to determine the new performance, with N1 = 1750 RPM and N2 = 2000 RPM. The first step is to read the capacity, head, and horsepower at several points on the 13 diameter curve in Fig. 9. For example, one point may be near the best efficiency point where the capacity is 300 GPM, the head is 160 ft, and the BHP is approx. 20 hp. 300 1750 = Q2 2000 160 = H2 Q2 = 343 gpm
2

To illustrate the use of these laws, refer to Fig. 8. It shows the performance of a particular pump at 1750 RPM with various impeller diameters. This performance data has been determined by actual tests by the manufacturer. Now assume that you have a 13" maximum diameter impeller, but you want to belt drive the pump at 2000 RPM.

2. With speed, N, held constant: A. Q1 D = 1 Q2 D2

B.

H1 D1 = H2 D2

( )

(2000)
1750 1750

C.

When the performance (Q1, H1, & BHP1) is known at some particular speed (N1) or diameter (D1), the formulas can be used to estimate the performance (Q2, H2, & BHP2) at some other speed (N2) or diameter (D2). The efficiency remains nearly constant for speed changes and for small changes in impeller diameter.

BHP1 D1 = BHP2 D2

( )

This will then be the best efficiency point on the new 2000 RPM curve. By performing the same calculations for several other points on the 1750 RPM curve, a new curve can be drawn which will approximate the pump's performance at 2000 RPM, Fig. 9.

20 = BHP2

( 2000)

H2 = 209 ft. BHP2 30 hp

Trial and error would be required to solve this problem in reverse. In other words, assume you want to determine the speed required to make a rating of 343 GPM at a head of 209 ft. You would begin by selecting a trial speed and applying the affinity laws to convert the desired rating to the corresponding rating at 1750 RPM. When you arrive at the correct speed, 2000 RPM in this case, the corresponding 1750 RPM rating will fall on the 13" diameter curve.

Fig. 9

TECH-A

1112

TECH-A-10 System Curves

For a specified impeller diameter and speed, a centrifugal pump has a fixed and predictable performance curve. The point where the pump operates on its curve is dependent upon the characteristics of the system in which it is operating, commonly called the System Head Curve...or, the relationship between flow and hydraulic losses* in a system. This representation is in a graphic form and, since friction losses vary as a square of the flow rate, the system curve is parabolic in shape.

The parabolic shape of the system curve is again determined by the friction losses through the system including all bends and valves. But in this case there is a positive static head involved. This static head does not affect the shape of the system curve or its steepness, but it does dictate the head of the system curve at zero flow rate.

POSITIVE STATIC HEAD

The operating point is at the intersection of the system curve and pump curve. Again, the flow rate can be reduced by throttling the discharge valve.

0
By plotting the system head curve and pump curve together, it can be determined: 1. Where the pump will operate on its curve. 2. What changes will occur if the system head curve or the pump performance curve changes. NO STATIC HEAD ALL FRICTION As the levels in the suction and discharge are the same (Fig. 1), there is no static head and, therefore, the system curve starts at zero flow and zero head and its shape is determined solely from pipeline losses. The point of operation is at the intersection of the system head curve and the pump curve. The flow rate may be reduced by throttling valve.

H 0
Fig. 2 Positive Suction Head

0
Fig. 1 No Static Head - All Friction

* Hydraulic losses in piping systems are composed of pipe friction losses, valves, elbows and other fittings, entrance and exit losses (these to the entrance and exit to and from the pipeline normally at the beginning and end not the pump) and losses from changes in pipe size by enlargement or reduction in diameter.

1113

TECH-A

NEGATIVE (GRAVITY) HEAD

In this illustration, a certain flow rate will occur by gravity head alone. But to obtain higher flows, a pump is required to overcome the pipe friction losses in excess of H the head of the suction above the level of the discharge. In other words, the system curve is plotted exactly as for any other case involving a static head and friction head, except the static head is now negative. The system curve begins at a negative value and shows the limited flow rate obtained by gravity alone. More capacity requires extra work.

MOSTLY LIFT- LITTLE FRICTION HEAD

The system head curve in this illustration starts at the static head H and zero flow. Since the friction losses are relatively small (possibly due to the large diameter pipe), the system curve is flat. In this case, the pump is required to overcome the comparatively large static head before it will deliver any flow at all.

HEAD

H (NEGATIVE)

PUMP CURVE

FLAT SYSTEM H PUMP CURVE

FLOW RATE
Fig. 4 Mostly Lift - Little Friction Head

HEAD

SYSTEM CURVE

FLOW RATE

-H
Fig. 3 Negative (Gravity) Head

TECH-A

1114

TECH-A-11 Basic Formulas and Symbols

Formulas
GPM = 0.002 x Lb./Hr. Sp. Gr. GPM = GPM = 449 x CFS H = 2.31 x psi Sp. Gr. Lbs./Hr. 500 x Sp. Gr.

Symbols
GPM = gallons per minute CFS = cubic feet per second Lb. = pounds Hr. = hour BBL = barrel (42 gallons) Sp. Gr. = specific gravity H = head in feet psi = pounds per square inch In. Hg. = inches of mercury hv = velocity head in feet V = velocity in feet per second g = 32.16 ft/sec2 (acceleration of gravity)

GPM = 0.7 x BBL /Hr. H = 1.134 x In. Hg. Sp. Gr.

2 hv = V = .0155 V2 2g

141.5 Sp. Gr. = 131.5 + degrees A.P.I. NC = 187.7 f Ns = N GPM H 3/4

2 H = v 2g 3 f = PL mEI

Eff. = GPM x H x Sp. Gr. 3960 x BHP

BHP = GPM x H x Sp. Gr. = GPM x psi 3960 x Eff. 1715 x Eff.

V = GPM x 0.321 = GPM x 0.409 A (I.D.) 2

A = area in square inches I.D. = inside diameter in inches BHP = brake horsepower Eff. = pump efficiency expressed as a decimal Ns = specific speed N = speed in revolutions per minute v = peripheral velocity of an impeller in feet per second D = Impeller in inches Nc = critical speed f = shaft deflection in inches P = total force in lbs. L = bearing span in inches m = constant usually between 48 and 75 for pump shafts E = modules of elasticity, psi 27 to 30 million for steel

v =NxD 229

DEG. C DEG. F

= (DEG. F - 32) x 5 / 9

= (DEG. C x 5 / 9) + 32

*SEE SECTION TECH-D-8C FOR SLURRY FORMULAS

1115

TECH-A

TECH-B-1 Corrosion & Materials of Construction

Selecting the right pump type and sizing it correctly are critical to the success of any pump application. Equally important is the selection of materials of construction. Choices must be made between metals and/or non-metals for pump components that come into contact with the pumpage. In addition, gaskets and O-ring material selections must be made to assure long leak-free operation of the pump's dynamic and static sealing joints. To assist in proper selection, included in this section is a brief discussion of specific types of corrosion and a general material selection guide.

Section TECH-B Pump Application Data

ing liquid resulting in a relatively uniform metal loss over the exposed surface. This is the most common type of corrosion and it can be minimized by the selection of a material which offers resistance to the corroding liquid.

Corrosion

(3) Intergranular corrosion is the precipitation of chromium carbides at the grain boundaries of stainless steels. It results in the complete destruction of the mechanical properties of the steel for the depth of the attack. Solution annealing or the use of extra low carbon stainless steels will eliminate intergranular corrosion. (4) Pitting Corrosion is a localized rather than uniform type of attack. It is caused by a breakdown of the protective film and results in rapid pit formation at random locations on the surface.

Corrosion is the destructive attack of a metal by chemical or electrachemical reaction with its environment. It is important to understand the various types of corrosion and factors affecting corrosion rate to properly select materials. TYPES OF CORROSION (1) Galvanic corrosion is the electro-chemical action produced when one metal is in electrical contact with another more noble metal, with both being immersed in the same corroding medium called the electrolyte. A galvanic cell is formed and current flows between the two materials. The least noble material called the anode will corrode while the more noble cathode will be protected. It is important that the smaller wearing parts in a pump be of a more noble material than the larger more massive parts, as in an iron pump with bronze or stainless steel trim. Following is a galvanic series listing the more common metals and alloys. Corroded End (Anodic, or least noble) Magnesium Magnesium Alloys Zinc Aluminum 2S Cadmium Aluminum 175T Steel or Iron Cast Iron Stainless Steel, 400 Series (Active) Stainless Steel, Type 304 (Active) Stainless Steel, Type 316 (Active) Lead-tin Solders Lead Tin Nickel (Active) Nickel base alloy (active) Brasses Copper Bronzes Copper-Nickel Alloy Monel Silver Solder Nickel (Passive) Nickel Base Alloy (Passive) Stainless Steel, 400 Series (Passive) Stainless Steel, Type 304 (Passive) Stainless Steel, Type 316 (Passive) Silver Graphite Gold Platinum Protected End (Cathodic, or most noble)

(5) Crevice or Concentration Cell Corrosion occurs in joints or small surface imperfections. Portions of the liquid become trapped and a difference in potential is established due to the oxygen concentration difference in these cells. The resulting corrosion may progress rapidly leaving the surrounding area unaffected. (6) Stress Corrosion is the failure of a material due to a combination of stress and corrosive environment, whereas the material would not be affected by the environment alone. (7) Erosion-Corrosion is the corrosion resulting when a metals protective film is destroyed by high velocity fluids. It is distinguished from abrasion which is destruction by fluids containing abrasive solid particles. pH VALUES

The pH of a liquid is an indication of its corrosive qualities, either acidic or alkaline. It is a measure of the hydrogen or hydroxide ion concentration in gram equivalents per liter. pH value is expressed as the logarithm to the base 10 of the reciprocal of the hydrogen ion concentration. The scale of pH values is from zero to 14, with 7 as a neutral point. From 6 to zero denotes increasing hydrogen ion concentration and thus increasing acidity, and from 8 to 14 denotes increasing hydroxide ion concentration and thus increasing alkalinity. The table below outlines materials of construction usually recommended for pumps handling liquids of known pH value

10 to 14 8 6 4 0 to to to to 10 8 6 4

pH Value

Corrosion Resistant Alloys Iron, Stainless Steel, Bronze, Carbon Steel

Material of Construction

(2) Uniform Corrosion is the overall attack on a metal by a corrod-

Corrosion Resistant Alloys

The pH value should only be used as a guide with weak aqueous solutions. For more corrosive solutions, temperature and chemical composition should be carefully evaluated in the selection of materials of construction.

TECH-B

1116

TECH-B-2 Material Selection Chart

he material selection chart (Table 1, Page 15) is intended to be a guide in the preliminary selection of economic materials. Corrosion rates may vary widely with temperature, concentration and the presence of trace elements or abrasive solids. Blank spaces in the chart indicate a lack of accurate corrosion data for those specific conditions. Maximum temperature limits are shown where data are available. Compatibility data for fluoropolymers EPDM, FKM, FFKM, PVDF and ECTFE (see code chart) were supplied by manufacturers.

A B X Steel Brz 316

Recommended Unsuitable Bronze

CODE FOR TABLE 1.

Useful resistance Carbon steel, cast iron and ductile iron Stainless steel

By Richard Blong, Global Chemical Market Manager, Goulds Pumps Inc., Seneca Falls, NY; and Brayton O. Paul, P.E., Senior Technical Editor

A-20

CD4MCu C-276 Ti Zi

Carpenter stainless

Alloy 2205 Alloy 2205 stainless steel Titanium unalloyed Zirconium

CD4MCu stainless steel

Wrought Hastelloy C-276 alloy

ETFE FP FRP

Ethylenetetrafluoroethylene (Tefzel )

Fluoropolymers (e.g., Teflon) including perfluoroalkoxy (PFA), Hyflon (MFA),polytetrafluoroethylene (PTFE) and fluorinated ethylene propylene (FEP) Fiber-reinforced plastic (vinylester resin) Ethylenepropylene rubber (Nordel )

EPDM FKM1

FKM2

FFKM PVDF ECTFE

Specialty grades; terpolymers comprising at least three of the following: HFP, VF2, tetrafluorethylene (TFE), perfluoromethylvinyl ether (PMVE) or ethylene (E). Specialty grades may have significantly improved chemical compatibility compared to standard grades in many harsh chemical environments (Viton, Tecnoflon). Copolymer of TFE and PMVE (Kalrez, Tecnoflon)

Standard grades; dipolymers of hexafluoropropylene (HFP) and vinylidene fluoride (VF2; Viton, Tecnoflon)

Polyvinylidene fluoride ( Kynar , Hylar, Solef ) Ethylene chlorotrifluoroethylene (Halar)

NOTE: Compatibility is dependent on specific form and/or grade. Contact elastomer manufacturer.

1117

TECH-B

Guidelines for information purposes and not design guidelines* TABLE 1. MATERIAL SELECTION CHART.
Corrosive Acetaldehyde, 70F Acetic acid, 70F Acetic acid, <50%, to boiling Acetic acid, >50%, to boiling Acetone, to boiling Aluminum chloride, <10%, 70F Aluminum chloride, >10%, 70F Aluminum chloride, <10%, to boiling Aluminum chloride, >10%, to boiling Aluminum sulphate, 70F Aluminum sulphate, <10%, to boiling Aluminum sulphate, >10%, to boiling Ammonium chloride, 70F Ammonium chloride, <10%, to boiling Ammonium chloride, >10%, to boiling Ammonium fluosilicate, 70F Arsenic acid, to 225F Barium chloride, 70F <30% Barium hydroxide, 70F Barium sulphide, 70F Benzoic acid Boric acid, to boiling Brine (acid), 70F Ammonium sulphate, <40%, to boiling Barium chloride, <5%, to boiling Barium chloride, >5%, to boiling Barium nitrate, to boiling B X X X A X X X X X X X X X X X X X X X X B X X X X B B X X X X X B X X B X X X X X B B B X X X X X A A B X A B X X X B B X X X X X X X B B X X X X X X B B X X X X X X X X B B X X X B B X B X X X X A A B A A X X X X B X B X X B X X B B B X X A B B B X X X B X B X B X B B X X A A X A A B X X X A B A A A A A B B X X A B B X B B B X B B B B B A B B A X X X B B B B B X B B X X A A B A A B X B X A B Alloy Steel Brz 316 A-20 CD4MCuN 2205 C-276 A A X A B X X X X B X X X X X X X B B B X X A B B B X X X B X B X B X B B X X A A X A A B X A B A A A A A B B X X A A B B B X B B B B B X A B B B B B A X X X B B B B B B B X X X A A A A B B X X B A A A A A A A B B A A A A A B B A B B B A A B A B B B B B A A A A A B A B A A B B A A A B Ti A A A A A B B X X A A X A A X X A B A X A B A A B B X X A A A A B A A A A A A A A A A A B A A A A A B Zi A A A A A A A A A A B A A X X A B A X A B A A B A ETFE A A 104C 104C A A 104C 104C 104C 104C 104C 104C 104C A A A A 104C 104C 104C 104C A A A A A A A A A A A A A A A A FP A A A A A A A A A A A A A A A A A A A A A FRP EPDM X X X A A X X A A X A A A B A A A A A A A A A A A A A A A A A A FKM1 FKM2 FFKM PVDF ECTFE X X X B A A X A B A X X A A A A A A A A X A A A A A X B B A A A A A A A A B A A A A A X A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A B X X 40C) 40C) A A A A A A A A A A A (to A A (to A B A X A A

A A A A A A A A

A A

A A A

A A B

A A A

A A A A A A A A A A A

A A A A A A A A A A A A A A A A A

A A A A A A A A A A A A A A A A A

A A

Boron trichloride, 70F dry Bromine (dry), 70F Calcium bisulphite

A X A X X A A B B

A X A A B A A A A

A X A A A A A A A

110C A

A A

Boron trifluoride, 70F 10%, dry Bromine (wet), 70F

X A A X A A B

A X X A A X X

Calcium bisulphite, 70F Calcium chloride, 70F Calcium chloride <5%, to boiling Calcium chloride >5%, to boiling Calcium hydroxide, 70F Calcium hydroxide, <30%, to boiling Calcium hydroxide, >30%, to boiling Calcium hypochlorite, <2%, 70F Calcium hypochlorite, >2%, 70F Carbolic acid, 70F (phenol) Carbon bisulphide, 70F Carbonic acid, 70F Chloric acid, 70F

X X

A A

A A

95C A A A A

A A A A A A

104C 104C 104C 104C A A A

A A A A A A A

A A A A B A A

A B B B B A A

A A A A A A A

A A A A A A A

A A A A A

50C A A

Carbon tetrachloride, dry to boiling Chlorinated water, 70F Chloroacetic acid, 70F Chromic acid, <30% Chlorosulphonic acid, 70F

A B X A

104C 149C A A X

X A X X

B X X A

A B X A

A X X

65C

80C

TECH-B

1118

Corrosive Citric acid Copper nitrate, to 175F Cresylic acid Cupric chloride Copper sulphate, to boiling Cyanohydrin, 70F Dichloroethane Diethylene glycol, 70F Ethanolamine, 70F Ethers, 70F Dinitrochlorobenzene, 70F (dry) Ethyl alcohol, to boiling Ethyl cellulose, 70F Ethyl chloride, 70F Ethyl sulphate, 70F Ethyl mercaptan, 70F Ethylene chlorohydrin, 70F Ethylene dichloride, 70F Ethylene glycol, 70F Ethylene oxide, 70F Ferric nitrate, 70F

Steel Brz 316 A-20 CD4MCuN 2205 X X X X X X X A X B B A A X X X X X B X X X X X X B X X X X X X X X X X X X X X B X X X B X X A X X A X A X X X X X B B B X B A B B X B B B B X X X X X X B X X X X X X X B X X B B X B X X X A X X X X X A X A B X B B B X A A B A B B B B B B B B B X X B X A X X X X X B X X X X B X X B A B X A B B B B X A X X X A A B B B B B X A A B A A B A A A B B B B X X A B A B X X X B B B X B B B B X B A B X A B A B A X A B A A A A B X B B B B A B B B B B B X X B X A X X B A B X A A A B A B B B X B B A A B A A B A A A B B B B X X A B B A A B X X X B B B X X B A B B B A B X B A B A X B A A

C-276 A B A B B B B A A A B B A B A A A A B B B A B A A A A A A A

Ti A B A B A A A A A A A A A A A A A B B A A X B X A X X X

Zi A A X A A A A B A A A A A A A B X A A A A A A B A B A

ETFE A A A A 104C A A A A A

FP A A A A A A A A A A A A

FRP EPDM A A A A

FKM1 FKM2 FFKM PVDF ECTFE A A A A X A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A B

A A X X

65C A A A B A X A A A A A A A A A A A A A A X

65C A

A A X X X X X X A A X A A A B B

B X X X

A X X

23C X A A A A A A A A A A A A A A A A A A A A A B A

104C A A A A A A A A A A 104C A A A A A A

A A A A A A A A A A A

A X X B X

B B B A A A A A A

A A B A A

Ferric chloride, <5%, 70F Ferric chloride, >5%, 70F Ferric sulphate, 70F Ferrous sulphate, 70F Formic acid, to 212F Freon, 70F

A A A A A

A A A A A

Formaldehyde, to boiling Hydrochloride acid, <1%, 70F Hydrochloric acid, >20%, 70F Hydrocyanic acid, 70F

A A A A A A A A A

Hydrochloric acid, 1% to 20%, 70F Hydrochloric acid, <1/2%, 175F Hydrochloric acid, 1/2% to 2%, 175F Hydrogen peroxide, <30%, <150F Hydrofluoric acid, <20%, 70F Hydrofluoric acid, >20%, 50F Hydrofluoric acid, to boiling Hydrofluorsilicic acid, 70F Lactic acid, <50%, 70F Lactic acid, >50%, 70F Lime slurries, 70F

X X

A A A A

A X

A/X1 A A A A X

A/X1 A A B A B

A/X1 A A A A A

A/B1 A A A A A

A X A X

A A A A

B X X A B

B A B B B A A B A A A B B A A B X A

A X X A A A B A B B A A A A A X

A X X A A A B A B B A A A X

A A A A A

A A A A A

B X X A A

B B B A A

A A A A A

A A A A A A A A A A A A A A A

B A A A A

A A A A A

X X X A B X X A B A B

A A A A A A

B X A A A

A B A A A

B A

A A

Lactic acid, <5%, to boiling Magnesium chloride, 70F Magnesium chloride, <5%, to boiling Magnesium chloride, >5%, to boiling Magnesium hydroxide, 70F Magnesium sulphate Maleic acid Mercaptans

104C 104C 104C A A A A A A A A

A A A

A A

A A

A A

50C 140C 140C 135C 120C A A A A A

A A

A A

A A A

A A A A A A A

B X A

A A A

A A A

B A

A A

A X A

A A

A B A

Mercuric chloride, <2%, 70F Mercurous nitrate, 70F Methyl alcohol, 70F

1119

TECH-B

Corrosive

Naphthalene sulphonic acid, 70F Napthalenic acid Nickel chloride, 70F Nickel sulphate Nitric acid

Steel Brz 316 A-20 CD4MCuN 2205 X X X X X A A A X X X B X B X X X X X X X B X B B X B B X X X X X B X X X B B X B B B X B X B X X X B X X X X X X X A A X X X X X B X X X X X X B X X B X X X B B B X X B B X B X X B B X X A X B X X X X X X X B B X B B A A A X X B B X B B A A B X X A B X A A B B A B B X B B B B B X B B B B A B B X X X X A B B B B B B B B A A A X X B B B A B A A B B X A A B A A A B A B B B B B A B A B B A B B A B A X X X X A B B B B B X B B A A A X X B B X B B A A B X X A B X A A B B A B B X B B B B B X B B B B A B B X X X X A B B B B B B B B A A A X X B B B A B A A B B X A A B A A A B A B B A B B B B A B B A B B B A B A X X X X B A B

C-276 B B A B X A A A A B B B B B A A A A B A A B B B A A B B B A B A B A B B A A A B A A A B A B B B A B

Ti B B A A A X B X

Zi B A B A A X A

ETFE A A A A

FP A A A A

FRP EPDM A X A A X A B X B X A B B A A A A

FKM1 FKM2 FFKM PVDF ECTFE A A A X B X X X B B B A A B X A A A A B A A A B A A A A B X B A A A B A X X X B B A A A A X A A A A B A A A B A A A A B B B A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A 70%, 90%, 50C 70C A A A A B A A X A 120C A X B 50C A 120C A 50C A A X A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Nitrobenzene, 70F Nitroethane, 70F Nitropropane, 70F Nitrous acid, 70F Nitrous oxide, 70F Oleic acid Oleum acid, 70F Oxalic acid Palmitic acid Phenol (see carbolic acid) Phosgene, 70F Phosphoric acid, <10%, 70F Phosphoric acid, >10% to 70%, 70F Phosphoric acid, <20%, 175F Phosphoric acid, >20%, 175F, <85% Phosphoric acid, >10%, boil, <85% Phthalic acid, 70F Picric acid, 70F Phthalic anhydride, 70F Potassium carbonate Potassium chlorate Potassium chloride, 70F Potassium cyanide, 70F Potassium dichromate Potassium ferricyanide

A B X X A A A A A A A B B A B B B A B A A A A X A B A X

A B B X A A A A A B A A X

A A A A A A A A A A A A A A A A A A A A A

A A A A A A A A A A A A A A A A A A A A A

X X X A X X X

A X X X

A B

A A A A A

A A A A A

A A A A A A A A A A A A A

140C 95C A A A X

A A A

140C 140C 95C 120C A A A A A

Potassium ferrocyanide, 70F Potassium hydroxide, 70F Potassium hypochlorite Potassium phosphate Seawater, 70F Potassium iodide, 70F Potassium permanganate Sodium bisulphate, 70F Sodium bromide, 70F Sodium carbonate Sodium cyanide Sodium fluoride Sodium chloride, 70F Sodium dichromate Sodium ethylate Sodium hydroxide, 70F Sodium hypochlorite Sodium lactate, 70F Stannic chloride, <5%, 70F Stannic chloride, >5%, 70F Sulphite liquors, to 175F Sulphur (molten) Sulphur dioxide (spray), 70F

A B A A A

A A A

A A A

A A

X B A

X B A

A A A

A A

A A A

A A

A A A

A A

A A A

A A

A A A

A A

A A A

100C B B B A A A A A A A A

A A A A A

A A A A A

140C 135C 95C A X A 140C A

A A A A

A A B A

A B A

A A A A

A A A

A A A A

B A

A A

A 40%, 95C A A A A A

B A

A A

A A

A A

120C A

A A

TECH-B

1120

Corrosive

Sulphuric acid, <2%, 70F

SteelBrz 316 A-20 CD4MCuN 2205 X X X B X X X X X X X X X X X X X X X X B X A X B X B X X B X X X X X X X X X B B B B A B B A A B B B B B X B X X X B B B B B B A A B A B X X B X X X X X X X X X B B B B A B B A A B B B B B X B X

C-276 Ti A A A A A B X A B B X X X X X X X X

Zi A A X X B X B B X

ETFE A A A A A A A X A A A A A A A A

FP A A A A A A A

FRP EPDM A A X X A X X A B B X X B X X X

FKM1 FKM2 FFKM PVDF ECTFE A A B B A A B B B A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A

Sulphuric acid, 2%t o 40%, 70F Sulphuric acid, <10%, 175F

Sulphuric acid, 40%, <90%, 70F

Sulphuric acid, 93% to 98%, 70F Sulphuric acid, 60% to 80%, 175F Sulphuric acid, <3/4%, boiling

Sulphuric acid, 10% to 60% & >80%, 175F X Sulphuric acid, 3/4% to 40%, boiling Sulphurous acid, 70F Urea, 70F X X

Sulphuric acid, 40% to 65% & >85%, boiling Sulphuric acid, 65% to 85%, boiling Titanium tetrachloride, 70F Tirchlorethylene, to boiling Vinyl acetate Zinc chloride Vinyl chloride

X X X B X B B B X X X

X X B B B B A B A A B B

X X A A A A A B A A B B

X X A A

X X B A

A A A A A A A A

X X X

B B B B A A A

120C 120C B A A

120C 120C 95C 120C A A A 20C A B A A A 120C

B A A B A A A

A B A A A A

B A A B

120C 20C 95C A A 140C 140C A A

Water, to boiling Zinc cyanide, 70F Zinc sulphate

A A

A B

A A

A A

A A

* NOTE: The use of tables, graphs and charts, and text suggestions contained in these guidelines is provided for information purposes only. The performance of materials in services can be affected by minor variations in the operating environment and pumping operating conditions that may affect corrosion performance. It is the responsibility of the user to determine the operating conditions and suitability of selected materials. It is the users responsibility to ensure that a material will be satisfactory in the intended service and environment. Before using any material, the end user should satisfy himself as to the suitability of any material for the proposed end use.

Elastomer Selection Guide

Elastomer Natural Rubber Shore (A) Hardness 40

Please use the following chart as a general guide only. Refer to detailed selection tables or the factory for specific elastomer recommendations.
Max Temp Limit 154 F 149 F Resistance to Moderate Chemicals G (1)

pH Range 5 - 12

Abrasion E

Oils Hydrocarbons P

Polyurethane Neoprene Hypalon Nitrile

60

81

60

212 F

(1) Poor for oxidizing chemicals and strong acids. (2) Fine particles only (200 mesh or less). E = Excellent G = Good P = Poor

Chlorobutyl

50

55

220 F 300 F

3 - 12

3 - 11

E (2) G G

230 F

4 - 12

G (1) E

G (1) G (1) E

G G P E

1 - 14 3 - 12

1121

TECH-B

TECH-B-3 Piping Design

The design of a piping system can have an important effect on the successful operation of a centrifugal pump. Such items as sump design, suction piping design, suction and discharge pipe size, and pipe supports must all be carefully considered.

Selection of the discharge pipe size is primarily a matter of economics. The cost of the various pipe sizes must be compared to the pump size and power cost required to overcome the resulting friction head. The suction piping size and design is far more important. Many centrifugal pump troubles are caused by poor suction conditions. The suction pipe should never be smaller than the suction connection of the pump and, in most cases, should be at least one size larger. Suction pipes should be as short and as straight as possible. Suction pipe velocities should be in the 5 to 8 feet per second range unless suction conditions are unusually good.
ECCENTRIC REDUCER

Higher velocities will increase the friction loss and can result in troublesome air or vapor separation. This is further complicated when elbows or tees are located adjacent to the pump suction nozzle, in that uneven flow patterns or vapor separation keeps the liquid from evenly filling the impeller. This upsets hydraulic balance leading to noise vibration, possible cavitation, and excessive shaft deflection. Cavitation erosion damage, shaft breakage or premature bearing failure may result.

On pump installations involving suction lift, air pockets in the suction line can be a source of trouble. The suction pipe should be exactly horizontal, or with a uniform slope upward from the sump to the pump as shown in Fig. 1. There should be no high spots where air can collect and cause the pump to lose its prime. Eccentric rather than concentric reducers should always be used.
CHECK VALVE

LONG RADIUS ELBOW

GATE VALVE

(IF USED)

FOOT VALVE STRAINER ECCENTRIC REDUCER

(1a) CORRECT

CHECK VALVE

LONG RADIUS ELBOW SUCTION PIPE SLOPES UPWARDS FROM SOURCE OF SUPPLY GATE VALVE

(1b) CORRECT
FOOT VALVE (IF USED)

STRAINER AIR POCKET BECAUSE ECCENTRIC REDUCER IS NOT USED AND BECAUSE SUCTION PIPE DOES NOT SLOPE GRADUALLY UPWARD FROM SUPPLY

GATE VALVE

GATE VALVE SHOULD NOT BE BETWEEN CHECK VALVE AND PUMP

CHECK VALVE

(1c) WRONG

Fig. 1 Air Pockets in Suction Piping

TECH-B

1122

If an elbow is required at the suction of a double suction pump, it should be in a vertical position if at all possible. Where it is necessary for some reason to use a horizontal elbow, it should be a long radius elbow and there should be a minimum of three diameters of straight pipe between the elbow and the pump as shown in Fig. 2, for low suction energy pumps, and five pipe diameters for high suction energy pumps. Fig. 3 shows the effect of an elbow directly on the suction. The liquid will flow toward the outside of the elbow and result in an uneven flow distribution into the two inlets of the double suction impeller. Noise and excessive axial thrust will result.

There are several important considerations in the design of a suction supply tank or sump. It is imperative that the amount of turbulence and entrained air be kept to a minimum. Entrained air may cause reduced capacity and efficiency as well as vibration, noise, shaft breakage, loss of prime, and/or accelerated corrosion. The free discharge of liquid above the surface of the supply tank at or near the pump suction can cause entrained air to enter the pump. All lines should be submerged in the tank, and baffles should be used in extreme cases as shown in Fig. 4.

MUST BE AT

LEAST 5D

ECCENTRIC REDUCER-WITH TOP HORIZONTAL

ELBOW MUST BE VERTICAL WHEN NEXT TO PUMP (2b) WRONG

(2a) PERMISSABLE

Fig. 2 Elbows At Pump Suction

Fig. 3 Effect of Elbow Directly on Suction

1123

TECH-B

PUMP SUCTION

RECOMMENDED

RECOMMENDED

BAFFLE

PUMP SUCTION

PUMP SUCTION

RECOMMENDED

(4a)

(4b)

(4c)

Fig. 4 Keeping Air Out of Pump Improper submergence of the pump suction line can cause a vortex, which is a swirling funnel of air from the surface directly into the pump suction pipe. In addition to submergence, the location of the pipe in the sump and the actual dimensions of the sump are also important in preventing vortexing and/or excess turbulence. The submergence of the suction pipe must also be carefully considered. The amount of submergence required depends upon the size and capacity of the individual pumps as well as on the sump design. Past experience is the best guide for determining the submergence. The pump manufacturer should be consulted for recommendations in the absence of other reliable data.

For horizontal pumps, Fig. 5 can be used as a guide for minimum submergence and sump dimensions for flows up to approximately 5000 gpm. Baffles can be used to help prevent vortexing in cases where it is impractical or impossible to maintain the required submergence. Fig. 6 shows three such baffling arrangements. On horizontal pumps, a bell should be used on the end of the suction pipe to limit the entrance velocity to 3-8 feet per second. Also, a reducer at the pump suction flange to smoothly accelerate and stabilize the flow into the pump is desirable.

Fig. 5 Minimum Suction Pipe Submergence and Sump Dimensions

TECH-B

1124

FLAT BAFFLE

SIDE VIEW

SUCTION PIPE SUCTION PIPE

BAFFLE SMOOTHS OUT VORTEX

TOP VIEW

(6a)

(6b) Fig. 6 Baffle Arrangements for Vortex Prevention

(6c)

For larger units (over 5000 GPM) taking their suction supply for an intake sump (especially vertically submerged pumps), requires special attention. The following section (Intake System Design) addresses these larger pumps. INTAKE SYSTEM DESIGN

All of the dimensions In Figures 7 through 10 are based on the rated capacity of the pump. If operation at an increased capacity is to be undertaken for extended periods of time, the maximum capacity should be used for obtaining sump dimensions. If the position of the back wall is determined structurally, dimension B in Figures 7 to 10 may become excessive and a false back wall should be installed.

The function of the intake structure (whether it be an open channel, a fully wetted tunnel, a sump, or a tank) is to supply an evenly distributed flow to the pump suction. An uneven distribution of flow, characterized by strong local currents, can result in formation of surface or submerged vortices and with certain low values of submergence, may introduce air into the pump, causing a reduction of capacity, an increase in vibration and additional noise. Uneven flow distribution can also increase or decrease the power consumption with a change in total developed head. The ideal approach is a straight channel coming directly to the pump or suction pipe. Turns and obstructions are detrimental, since they may cause eddy currents and tend to initiate deep-cored vortices. The amount of submergence available is only one factor affecting vortex-free operation. It is possible to have adequate submergence and still have submerged vortices that may have an adverse effect on pump operation. Successful, vortex-free operation will depend greatly on the approach upstream of the sump.

Dimension S in Figures 7 and 9 is a minimum value based on the normal low water level at the pump or suction pipe bell, taking into consideration friction losses through the inlet screen and approach channel. Note that this dimension represents submergence at the intake, or the physical height of the water level above the intake relating to the prevention of eddy formations and vortexing.

The channel floor should be level for at least a distance Y (see Figures 7 through 10) upstream before any slope begins. The screen or gate widths should not be substantially less than W, and heights should not be less than the maximum anticipated water level to avoid overflow. Depending on the approach conditions before the sump, it may be necessary to construct straightening vanes in the approach channel, increase dimension A and/or conduct an intake model test to work out some other combination of these factors. Dimension W is the width of an individual pump cell or the center-tocenter distance of two pumps if no dividing wall is used. On multiple intake installations, the recommended dimensions in Figures 7 and 8 apply as noted above, and the following additional factors should be considered.

Complete analysis of intake structures can only be accurately accomplished by scale model tests. Model testing is especially recommended for larger pumping units. GENERAL DATA INFORMATION Subject to the qualifications of the foregoing statements, Figures 7 through 10 have been constructed for single and multiple intake arrangements to provide guidelines for basic sump dimensions. Since these values are composite averages for many pump types and cover the entire range of specific speeds, they are not absolute values but typical values subject to variations.

Reprinted from Hydraulic Institute Standard

1125

TECH-B

As shown in Fig. 10 (A), low velocity and straight in-line flow to all units simultaneously is a primary recommendation. Velocities in the sump should be approximately one foot per second, but velocities of two feet per second may prove satisfactory. This is particularly true when the design is based on a model study. Not recommended would be an abrupt change in the size of the inlet pipe to the sump or the inlet from one side introducing eddying. In many cases, as shown in Fig. 10 (B), pumps operate satisfactorily without separating walls below 5,000 GPM. If walls must be used for structural purposes or some pumps operate intermittently, then the walls should extend from the rear wall approximately five times the D dimension given in Fig. 7. If walls are used, increase dimension W by the thickness of the wall for correct centerline spacing and use round or ogive ends of walls. Not recommended is the placement of a number of pumps or suction pipes around the sides of a sump with or without dividing walls.

pipes in the sump leaves large vortex areas behind the intake which will cause operational trouble.

If the sump velocity, as shown in Fig. 10 (D), can be kept low (approximately one foot per second), an abrupt change from inlet pipe to sump can be accommodated if the sump length equals or exceeds the values shown. As ratio Z/P increases, the inlet velocity at P may be increased up to an allowed maximum of eight feet per second at Z/P 10. Intakes in line are not recommended unless a trench-type of intake is provided (per ANSI/HI 9.8), or the ratio of sump to intake size is quite large and intakes are separated by a substantial margin longitudinally. A sump can generally be constructed at less cost by using a recommended design. As shown in Fig. 10 (E), it is sometimes desirable to install pumps in tunnels or pipe lines. A drop pipe or false well to house the unit with a vaned inlet elbow facing upstream is satisfactory in flows up to eight feet per second. Without inlet elbow, the suction bell should be positioned at least two pipe (vertical) diameters above the top of the tunnel. The unit should not be suspended in the tunnel flow, unless the tunnel velocity Is less than two feet per second. There must be no air along the top of the tunnel, and the minimum submergence must be provided. In general: Keep inlet velocity to the sump below two feet per second. Keep velocity in sump below 1.5 foot per second. Avoid changing direction of flow from inlet to pump or suction pipe, or change direction gradually and smoothly, guiding flow.

Abrupt changes in size, as shown in Fig. 10 (C), from inlet pipe or channel to the sump are not desirable. Connection of a pipe to a sump is best accomplished using a gradually increasing taper section. The angle should be as small as possible, preferably not more than 10 degrees. With this arrangement, sump velocities less than one foot per second are desirable. Specifically not recommended is a pipe directly connected to a sump with suction intakes close to the sump inlet, since this results in an abrupt change in the flow direction. Centering pumps or suction

D = W =

(.0744Q)0.5 Recommended 2D S = Where: S Q D Fig. 7 Sump Dimensions

D + 0.574 Q / D1.5 inches Flow (GPM) inches

Y 4D A 5D C = B = .3D to .5D .75D

TECH-B

1126

Pump W/2 W/2 W W Single pump

Flow Trash Rack

Multiple sump W

Screen

Optional partial dividers (increase dimension W by the divider thickness) required above 5,000 GPM Y A

Flow

Fig. 8 Sump dimensions, plan view, wet pit type pumps

A B Y

Screen Trash Rack Min. Water Level

Note: 10 or less preferred with 1 ft./sec velocity max. at screen location shown. 15 max. with velocity reduced to 0.5 ft./sec

Fig. 9 Sump dimensions, elevation view, wet pit type pumps

1127

TECH-B

Reprinted from Hydraulic Institute Standard

Fig. 10 Multiple pump installations

TECH-B

1128

TECH-B-4A Sealing

The proper selection of a seal is critical to the success of every pump application. For maximum pump reliability, choices must be made between the type of seal and the seal environment. In addition, a sealless pump is an alternative which would eliminate the need for a dynamic type seal entirely. Sealing Area

Sealing Basics

There are two basic kinds of seals: static and dynamic. Static seals are employed where no movement occurs at the juncture to be sealed. Gaskets and O-rings are typical static seals. Dynamic seals are used where surfaces move relative to one another. Dynamic seals are used, for example, where a rotating shaft transmits power through the wall of a tank (Fig. 1), through the casing of a pump (Fig. 2), or through the housing of other rotating equipment such as a filter or screen. A common application of sealing devices is to seal the rotating shaft of a centrifugal pump. To best understand how such a seal functions, a quick review of pump fundamentals is in order. In a centrifugal pump, the liquid enters the suction of the pump at the center (eye) of the rotating impeller (Figures 3 and 4).

Rotating Shaft

Fig. 1 Cross Section of Tank and Mixer

Sealing Area

Fig. 2 Typical Centrifugal Pump

Discharge

Throat Rotary Impeller Suction Eye Shaft Stuffing Box or Seal Chamber Gland

Fig. 3 Centrifugal Pump, Liquid End

Casing

1129

TECH-B

As the impeller vanes rotate, they transmit motion to the incoming product, which then leaves the impeller, collects in the pump casing, and leaves the pump under pressure through the pump discharge.

Discharge

Discharge pressure will force some product down behind the impeller to the drive shaft, where it attempts to escape along the rotating drive shaft. Pump manufacturers use various design techniques to reduce the pressure of the product trying to escape. Such techniques include: 1) the addition of balance holes through the impeller to permit most of the pressure to escape into the suction side of the impeller, or 2) the addition of back pump-out vanes on the back side of the impeller. However, as there is no way to eliminate this pressure completely, sealing devices are necessary to limit the escape of the product to the atmosphere. Such sealing devices are typically either compression packing or end-face mechanical seals.

Casing

Impeller Vanes

Fig. 4 Fluid Flow in a Centrifugal Pump

Impeller

Suction Eye

Stuffing Box Packing

A typical packed stuffing box arrangement is shown in Fig. 5. It consists of: A) Five rings of packing, B) A lantern ring used for the injection of a lubricating and/or flushing liquid, and C) A gland to hold the packing and maintain the desired compression for a proper seal. The function of packing is to control leakage and not to eliminate it completely. The packing must be lubricated, and a flow from 40 to 60 drops per minute out of the stuffing box must be maintained for proper lubrication. The method of lubricating the packing depends on the nature of the liquid being pumped as well as on the pressure in the stuffing box. When the pump stuffing box pressure is above atmospheric pressure and the liquid is clean and nonabrasive, the pumped liquid itself will lubricate the packing (Fig. 6). When the stuffing box pressure is below atmospheric pressure, a lantern ring is employed and lubrication is injected into the stuffing box (Fig. 7). A bypass line from the pump discharge to the lantern ring connection is normally used providing the pumped liquid is clean. When pumping slurries or abrasive liquids, it is necessary to inject a clean lubricating liquid from an external source into the lantern ring

(Fig. 8). A flow of from .2 to .5 gpm is desirable and a valve and flowmeter should be used for accurate control. The seal water pressure should be from 10 to 15 psi above the stuffing box pressure, and anything above this will only add to packing wear. The lantern ring is normally located in the center of the stuffing box. However, for extremely thick slurries like paper stock, it is recommended that the lantern ring be located at the stuffing box throat to prevent stock from contaminating the packing. The gland shown in Figures 5 through 8 is a quench type gland. Water, oil, or other fluids can be injected into the gland to remove heat from the shaft, thus limiting heat transfer to the bearing frame. This permits the operating temperature of the pump to be higher than the limits of the bearing and lubricant design. The same quench gland can be used to prevent the escape of a toxic or volatile liquid into the air around the pump. This is called a smothering gland, with an external liquid simply flushing away the undesirable leakage to a sewer or waste receiver. Today, however, stringent emission standards limit use of packing to non-hazardous water based liquids. This, plus a desire to reduce maintenance costs, has increased preference for mechanical seals.

TECH-B

1130

Lantern Ring Stuffing Box Bushing

Sealing Liquid Connection

Packing Gland (Quench Type) Positive Fluid Pressure Above Atmospheric Pressure

Atmospheric Pressure

Stuffing Box Throat

Leakage Mechanical Packing

Fig. 5 Typical Stuffing Box Arrangement (Description of Parts)

Fig. 6 Typical Stuffing Box Arrangement When Stuffing Box Pressure is Above Atmospheric Pressure

Injected Fluid Atmospheric Pressure

Lantern Ring Location For Thick Slurries Including Paper Stock Leakage Into Pump

Injected Fluid From External Source Atmospheric Pressure

Leakage Into Pump

Normal Lantern Ring Connection

Mechanical Seals

Fig. 7 Typical Stuffing Box Arrangement When Stuffing Box Pressure is Below Atmospheric Pressure

Fig. 8 Typical Stuffing Box Arrangement When Pumping Slurries

A mechanical seal is a sealing device which forms a running seal between rotating and stationary parts. They were developed to overcome the disadvantages of compression packing. Leakage can be reduced to a level meeting environmental standards of government regulating agencies and maintenance costs can be lower. Advantages of mechanical seals over conventional packing are as follows:

1. Zero or limited leakage of product (meet emission regulations.) 2. Reduced friction and power loss. 4. Reduced maintenance costs. 3. Elimination of shaft or sleeve wear. 5. Ability to seal higher pressures and more corrosive environments.

6. The wide variety of designs allows use of mechanical seals in almost all pump applications.

1131

TECH-B

The Basic Mechanical Seal

All mechanical seals are constructed of three basic sets of parts as shown in Fig. 9: 1. A set of primary seal faces: one rotary and one stationary...shown in Fig. 9 as seal ring and insert.

2. A set of secondary seals known as shaft packings and insert mountings such as O-rings, wedges and V-rings.

3. Mechanical seal hardware including gland rings, collars, compression rings, pins, springs and bellows.

Coil Spring

Insert

Insert Mounting

Gland Ring Shaft Packing Seal Ring Gland Gasket

Fig. 9 A Simple Mechanical Seal

How A Mechanical Seal Works

The primary seal is achieved by two very flat, lapped faces which create a difficult leakage path perpendicular to the shaft. Rubbing contact between these two flat mating surfaces minimizes leakage. As in all seals, one face is held stationary in a housing and the other face is fixed to, and rotates with, the shaft. One of the faces is usually a non-galling material such as carbon-graphite. The other is usually a relatively hard material like silicon-carbide. Dissimilar materials are usually used for the stationary Insert and the rotating seal ring face in order to prevent adhesion of the two faces. The softer face usually has the smaller mating surface and is commonly called the wear nose. There are four main sealing points within an end face mechanical seal (Fig. 10). The primary seal is at the seal face, Point A. The leakage path at Point B is blocked by either an O-ring, a V-ring or a wedge. Leakage paths at Points C and D are blocked by gaskets or O-rings.

POINT C Gland Gasket

POINT D Insert Mounting

POINT A Face

The faces in a typical mechanical seal are lubricated with a boundary layer of gas or liquid between the faces. In designing seals for the desired leakage, seal life, and energy consumption, the designer must consider how the faces are to be lubricated and select from a number of modes of seal face lubrication. To select the best seal design, its necessary to know as much as possible about the operating conditions and the product to be sealed. Complete information about the product and environment will allow selection of the best seal for the application.

POINT B Shaft Packing

Fig. 10 Sealing Points for Mechanical Seal

TECH-B

1132

Mechanical Seal Types

Mechanical seals can be classified into several types and arrangements:

PUSHER:

Incorporate secondary seals that move axially along a shaft or sleeve to maintain contact at the seal faces. This feature compensates for seal face wear and wobble due to misalignment. The pusher seals advantage is that its inexpensive and commercially available in a wide range of sizes and configurations. Its disadvantage is that it's prone to secondary seal hang-up and fretting of the shaft or sleeve.

NON-PUSHER:

The non-pusher or bellows seal does not have to move along the shaft or sleeve to maintain seal face contact. The main advantages are its ability to handle high and low temperature applications, and does not require a secondary seal (not prone to secondary seal hang-up). A disadvantage of this style seal is that its thin bellows cross sections must be upgraded for use in corrosive environments.

UNBALANCED:

They are inexpensive, leak less, and are more stable when subjected to vibration, misalignment, and cavitation. The disadvantage is their relative low pressure limit. If the closing force exerted on the seal faces exceeds the pressure limit, the lubricating film between the faces is squeezed out and the highly loaded dry running seal fails.

BALANCED:

Balancing a mechanical seal involves a simple design change which reduces the hydraulic forces acting to close the seal faces. Balanced seals have higher pressure limits, lower seal face loading, and generate less heat. This makes them well suited to handle liquids with poor lubricity and high vapor pressures such as light hydrocarbons.

CONVENTIONAL:

Examples are ones which require setting and alignment of the seal (single, double, tandem) on the shaft or sleeve of the pump. Although setting a mechanical seal is relatively simple, today's emphasis on reducing maintenance costs has increased preference for cartridge seals.

CARTRIDGE:

Examples are ones which have the mechanical seal premounted on a sleeve including the gland and fit directly over the Model 3196 shaft or shaft sleeve (available single, double, tandem). The major benefit, of course, is no requirement for the usual seal setting measurements for their installation. Cartridge seals lower maintenance costs and reduce seal setting errors.

1133

TECH-B

Mechanical Seal Arrangements

SINGLE INSIDE: This is the most common type of mechanical seal. These seals are easily modified to accommodate seal flush plans and can be balanced to withstand high seal environment pressures. Recommended for relatively clear non-corrosive and corrosive liquids with satisfactory lubricating properties where cost of operation does not exceed that of a double seal. SINGLE OUTSIDE: If an extremely corrosive liquid has good lubricating properties, an outside seal offers an economical alternative to the expensive metal required for an inside seal to resist corrosion. The disadvantage is that it is exposed outside of the pump which makes it vulnerable to damage from impact and hydraulic pressure works to open the seal faces so they have low pressure limits (balanced or unbalanced).

DOUBLE GAS BARRIER (PRESSURIZED DUAL GAS):

Very similar to cartridge double seals...sealing involves an inert gas, like nitrogen, to act as a surface lubricant and coolant in place of a liquid barrier system or external flush required with conventional or cartridge double seals. This concept was developed because many barrier fluids commonly used with double seals can no longer be used due to new emission regulations. The gas barrier seal uses nitrogen or air as a harmless and inexpensive barrier fluid that helps prevent product emissions to the atmosphere and fully complies with emission regulations. The double gas barrier seal should be considered for use on toxic or hazardous liquids that are regulated or in situations where increased reliability is the required on an application.

DOUBLE (DUAL PRESSURIZED):

This arrangement is recommended for liquids that are not compatible with a single mechanical seal (i.e. liquids that are toxic, hazardous [regulated by the EPA], have suspended abrasives, or corrosives which require costly materials). The advantages of the double seal are that it can have five times the life of a single seal in severe environments. Also, the metal inner seal parts are never exposed to the liquid product being pumped, so viscous, abrasive, or thermosetting liquids are easily sealed without a need for expensive metallurgy. In addition, recent testing has shown that double seal life is virtually unaffected by process upset conditions during pump operation. A significant advantage of using a double seal over a single seal. The final decision between choosing a double or single seal comes down to the initial cost to purchase the seal, cost of operation of the seal, and environmental and user plant emission standards for leakage from seals. TANDEM (DUAL UNPRESSURIZED): Due to health, safety, and environmental considerations, tandem seals have been used for products such as vinyl chloride, carbon monoxide, light hydrocarbons, and a wide range of other volatile, toxic, carcinogenic, or hazardous liquids. Tandem seals eliminate icing and freezing of light hydrocarbons and other liquids which could fall below the atmospheric freezing point of water in air (32F or 0C). (Typical buffer liquids in these applications are ethylene glycol, methanol, and propanol.) A tandem also increases online reliability. If the primary seal fails, the outboard seal can take over and function until maintenance of the equipment can be scheduled.

TECH-B

1134

Mechanical Seal Selection

1. Liquid 2. Pressure 3. Temperature 4. Characteristics of Liquid 5. Reliability and Emission Concerns

The proper selection of a mechanical seal can be made only if the full operating conditions are known:

2. Pressure. The proper type of seal, balanced or unbalanced, is based on the pressure on the seal and on the seal size.

3. Temperature. In part, determines the use of the sealing members. Materials must be selected to handle liquid temperature. 4. Characteristics of Liquid. Abrasive liquids create excessive wear and short seal life. Double seals or clear liquid flushing from an external source allow the use of mechanical seals on these difficult liquids. On light hydrocarbons balanced seals are often used for longer seal life even though pressures are low.

Seal Environment

1. Liquid. Identification of the exact liquid to be handled is the first step in seal selection. The metal parts must be corrosion resistant, usually steel, bronze, stainless steel, or Hastelloy. The mating faces must also resist corrosion and wear. Carbon, ceramic, silicon carbide or tungsten carbide may be considered. Stationary sealing members of Buna, EPR, Viton and Teflon are common.

5. Reliability and Emission Concerns. The seal type and arrangement selected must meet the desired reliability and emission standards for the pump application. Double seals and double gas barrier seals are becoming the seals of choice.

The number one cause of pump downtime is failure of the shaft seal. These failures are normally the result of an unfavorable seal environment such as improper heat dissipation (cooling), poor lubrication of seal faces, or seals operating in liquids containing solids, air or vapors. To achieve maximum reliability of a seal application, proper choices of seal housings (standard bore stuffing box, large bore, or large tapered bore seal chamber) and seal environmental controls (CPI and API seal flush plans) must be made. STANDARD BORE STUFFING BOX COVER Designed thirty years ago specifically for packing. Also accommodates mechanical seals (clamped seat outside seals and conventional double seals.) CONVENTIONAL LARGE BORE SEAL CHAMBER Designed specifically for mechanical seals. Large bore provides increased life of seals through improved lubrication and cooling of faces. Seal environment should be controlled through use of CPI or API flush plans. Often available with internal bypass to provide circulation of liquid to faces without using external flush. Ideal for conventional or cartridge single mechanical seals in conjunction with a flush and throat bushing in bottom of chamber. Also excellent for conventional or cartridge double or tandem seals.

LARGE BORE SEAL CHAMBERS

Introduced in the mid-80s, enlarged bore seal chambers with increased radial clearance between the mechanical seal and seal chamber wall, provide better circulation of liquid to and from seal faces. Improved lubrication and heat removal (cooling) of seal faces extend seal life and lower maintenance costs.

BigBoreTM Seal Chamber

TaperBoreTM Seal Chamber

1135

TECH-B

Large Tapered Bore Seal Chambers

Provide increased circulation of liquid at seal faces without use of external flush. Offers advantages of lower maintenance costs, elimination of tubing/piping, lower utility costs (associated with seal flushing) and extended seal reliability. The tapered bore seal chamber is commonly available with ANSI chemical pumps. API process pumps use conventional large bore seal chambers. Paper stock pumps use both conventional large bore and large tapered bore seal chambers. Only tapered bore seal chambers with flow modifiers provide expected reliability on services with or without solids, air or vapors. Conventional Tapered Bore Seal Chamber: Mechanical Seals Fail When Solids or Vapors Are Present in Liquid

Many users have applied the conventional tapered bore seal chamber to improve seal life on services containing solids or vapors. Seals in this environment failed prematurely due to entrapped solids and vapors. Severe erosion of seal and pump parts, damaged seal faces and dry running were the result.

Modified Tapered Bore Seal Chamber with Axial Ribs: Good for Services Containing Air, Minimum Solids

This type of seal chamber will provide better seal life when air or vapors are present in the liquid. The axial ribs prevent entrapment of vapors through improved flow in the chamber. Dry running failures are eliminated. In addition, solids less than 1% are not a problem.

The new flow pattern, however, still places the seal in the path of solids/liquid flow. The consequence on services with significant solids (greater than 1%) is solids packing the seal spring or bellows, solids impingement on seal faces and ultimate seal failure. Goulds Standard TaperBoreTM PLUS Seal Chamber: The Best Solution for Services Containing Solids and Air or Vapors

To eliminate seal failures on services containing vapors as well as solids, the flow pattern must direct solids away from the mechanical seal, and purge air and vapors. Goulds Standard TaperBoreTM PLUS completely reconfigures the flow in the seal chamber with the result that seal failures due to solids are eliminated. Air and vapors are efficiently removed eliminating dry run failures. Extended seal and pump life with lower maintenance costs are the results.

Goulds TaperBoreTM Plus : How It Works

The unique flow path created by the Vane Particle Ejector directs solids away from the mechanical seal, not at the seal as with other tapered bore designs. And the amount of solids entering the bore is minimized. Air and vapors are also efficiently removed. On services with or without solids, air or vapors, Goulds TaperBoreTM PLUS is the effective solution for extended seal and pump life and lower maintenance costs.

1 2 3 4 1 5 2
1 3 2 4 3 5 4 5

1 1 2 2 1 3 3 1 2 4 4 1 2 3 5 5 2 3 4 3 4 5 5 4 5

Solids/liquid mixture flows toward mechanical seal/seal chamber. Turbulent zone. Some solids continue to flow toward shaft. Other solids are forced back out by centrifugal force (generated by back pump-out vanes). Clean liquid continues to move toward mechanical seal faces. Solids, air, vapors flow away from seal. Low pressure zone create by Vane Particle Ejector. Solids, air, vapor liquid mixture exit seal chamber bore. Flow in TaperBoreTM PLUS seal chamber assures efficient heat removal (cooling) and lubrication. Seal face heat is dissipated. Seal faces are continuously flushed with clean liquid.

1 2 3 4 5

1 2 3 4 5

TECH-B

1136

Patented Cyclone Seal Chamber Design

Heres How It Works:

At the heart of our program is the patented cyclone seal chamber that not only provides the optimum seal environment in the presence of solids and vapors, but also improves maintainability and reduces installation cost by eliminating seal flush piping.

1 2

Cast helical ribs act as a barrier to particles traveling within the inward boundary layer flow found on the tapered walls of the seal chamber.

Solids removal is key to prevent seal and seal chamber wear as well as clogging of the mechanical seal for guaranteed reliability.

Once caught in the grooves of the helical ribs, the cyclone-like rotational velocity created by the impeller carries particles out of the seal chamber away from the seal.

JACKETED STUFFING BOX COVER

Stuffing Box Cover and Seal Chamber Guides

Standard Bore Stuffing Box Cover Jacketed Stuffing Box Cover Conventional Large Bore Jacketed Large Bore Tapered Large Bore with Axial Ribs Tapered Large Bore with Patented Vane Particle Ejector (Alloy Construction) Stuffing Box Cover Seal Chamber

Designed to maintain proper temperature control (heating or cooling) of seal environment. (Jacketed covers do not help lower seal face temperatures to any significant degree). Good for high temperature services that require use of a conventional double seal or single seal with a flush and API or CPI plan 21.

JACKETED LARGE BORE SEAL CHAMBER

Maintains proper temperature control (heating or cooling) of seal environment with improved lubrication of seal faces. Ideal for controlling temperature for services such as molten sulfur and polymerizing liquids. Excellent for high temperature services that require use of conventional or cartridge single mechanical seals with flush and throat bushing in bottom of seal chamber. Also, great for conventional or cartridge double or tandem seals.

The following two selection guides are designed to assist selection of the proper seal housing for a pump application. Stuffing Box and Seal Chamber Application Guide Application

Use for soft packing. Outside mechanical seals. Double seals. Also, accommodates other mechanical seals.

Same as above, but used in high temperature applications when the temperature of the seal area needs to be controlled.

Use for all mechanical seal applications where the seal environment requires use of CPI or API seal flush pans. Cannot be used with outside type mechanical seals Same as Large Bore but also need to control temperature of liquid in seal area. Clean services that require use of single mechanical seals. Can also be used with cartridge double seals. Also, effective on services with light solids up to 1% by weight. Paper stock to 1% by weight. Services with light to moderate solids up to 10% by weight. Paper stock to 5% by weight. Ideal for single mechanical seals. No flush required. Also, accommodates cartridge double seals. Cannot be used with outside mechanical seals.

1137

TECH-B

Selection Guide
Goulds engineered seal chambers provide best seal environment for selected sealing arrangements/services.

TYPE 1

Standard Bore Conventional Large Tapered Bore Lower seal face temperStuffing Box Cover Bore
Designed for packing. Also accommodates mechanical seals. Enlarged chamber for increased seal life through improved lubrication and cooling. Seal environment should be controlled through use of CPI flush plans.

TYPE 2

TYPE 3

TYPE 4

A B C

Ideally Suited Acceptable Not Recommended

atures, self-venting and draining. Solids and vapors circulated away from seal faces wtih VPE and cyclone seal chamber designs. Often no flush required. Superior patented design maximizes seal life with or without solids and vapor in liquid.

Jacketed Stuffing Box

TYPE 5

Jacketed Large Bore

Maintains proper temperature control (heating or cooling) of seal environment with improved lubrication of seal faces. Ideal for controlling temperatures on services such as molten sulfur and polymerizing liquids.

Maintains proper temperature control (heating or cooling) of seal environment.

Service Acceptable Ideally Suited

Entrained Air or Vapor Ambient Water With Flush C B A A B A A A A A A A A C B B A -

Solids 0-10%, No Flush

Slurries 0-5%, No Flush Temperature Control High Boiling Point Liquids, no flush

Solids up to and greater than 10% With Flush Paper Stock 0-5%, With No Flush Paper Stock 0-5%, With Flush

C C C A

C C B

Self-Venting and Draining Seal Face Heat Removal Molten or Polymerizing Liquid, No Flush Molten or Polymerizing Liquid With Flush

C C

C C C B A

C A A

C C C B

C C C A A A

TECH-B

1138

Environmental Controls
1. Corrosion 2. Temperature Control CORROSION 3. Dirty or Incompatible Environments

Environmental controls are necessary for reliable performance of a mechanical seal on many applications. Goulds Pumps and the seal vendors offer a variety of arrangements to combat these problems:

Corrosion can be controlled by selecting seal materials that are not attacked by the pumpage. When this is difficult, external fluid injection of a non-corrosive chemical to lubricate the seal is possible. Single or double seals could be used, depending on if the customer can stand delusion of his product. TEMPERATURE CONTROL As the seal rotates, the faces are in contact. This generates heat and if this heat is not removed, the temperature in the stuffing box or seal chamber can increase and cause sealing problems. A simple by-pass of product over the seal faces will remove the heat generated by the seal (Fig. 25). For higher temperature services, by-pass of product through a cooler may be required to cool the seal sufficiently (Fig. 26). External cooling fluid injection can also be used. DIRTY or INCOMPATIBLE ENVIRONMENTS Mechanical seals do not normally function well on liquids which contain solids or can solidify on contact with the atmosphere. Here, by-pass flush through a filter, a cyclone separator or a strainer are methods of providing a clean fluid to lubricate seal faces. Strainers are effective for particles larger than the openings on a 40 mesh screen. Cyclone separators are effective on solids 10 micron or more in diameter, if they have a specific gravity of 2.7 and the pump develops a differential pressure of 30-40 psi. Filters are available to remove solids 2 microns and larger. If external flush with clean liquid is available, this is the most fail proof system. Lip seal or restricting bushings are available to control flow of injected fluid to flows as low as 1/8 GPM. Quench type glands are used on fluids which tend to crystallize on exposure to air. Water or steam is put through this gland to wash away any build up. Other systems are available as required by the service.

Fig. 25

Fig. 26

1139

TECH-B

API and CPI Plans

API and CPI mechanical seal flush plans are commonly used with API and CPI process pumps. The general arrangement of the plans are similar regardless of the designation whether API or CPI. The difference between the flush plans is the construction which provides applicable pressure-temperature capability for each type of pump. API plans have higher pressure and temperature capability than CPI plans. Each plan helps provide critical lubrication and cooling of seal faces to maximize seal reliability. Plan No. Recommended Applications 01 02 11 12 13 21 22 23 31 32 33 41 51 52 53 54

Single mechanical seals and TDH less then 125 feet.

Used with some outside seals. In most cases not recommended.

Single and tandem seals. Always consider a plan 11 with balanced seals. Apply when TDH is greater than 125 ft.

Same application as 11. Additionally, a 12 will strain particles from the flush liquid. This helps prevent solid impingement on seal faces. Single and tandem seals. Use when difference in pressure between the seal chamber or stuffing box and pump suction exceed 35 psi. Single and tandem seals. Required when the flush needs to be cooled before flushing at the seal faces. (ex. water above 200F, light hydrocarbons or any other liquids with poor lubricating qualities and high vapor pressures.)

Same application as 21. Additionally, a plan 22 will strain particles from the flush liquid. This helps prevent solid impingement on seal faces. Single and tandem seals. Use when difference in pressure between the seal chamber or stuffing box and pump suction exceed 35 psi. 3600 RPM only. Single and tandem seals. Apply when strainers are inadequate to clean flushing liquid. Used with double seals when external system is available from user.

Single and tandem seals. Required when pumpage is not suitable to lubricate seal faces. Use of bushing or lip seal is also recommended. Apply with liquids that require simultaneous cyclone separation and cooling. (Single and tandem seals).

Single seals. Required when sealed liquid will crystallize, coke, solidify, etc. at seal faces if contact with air. Common blankets are isopropyl alcohol, glycol, and water. Normally used with FVD gland and bushing or packed auxiliary box. Double seals. Plan provides flushing and cooling to both sets of seal faces. Pumping ring recommended. Double seals or packed auxiliary stuffing box.

Tandem seals. Plan provides buffer liquid for outside seal. A plan 01 or plan 11 is also recommended with tandem seals to properly flush inboard seal. Pumping rings recommended.

Maximum Sealing Flexibility - Dynamic Seal

For Elimination of Mechanical Seal Problems and Reduced Maintenance
Goulds Dynamic Seal pumps are designed to handle the tough applications where conventional mechanical seals or packing require outside flush and constant, costly attention. The major advantage is that through Goulds patented design (No. 5,344,163) external seal water is not required, thus eliminating leakage, pumpage contamination, product dilution and problems associated with piping from a remote source.
Stuffing Box Cover Repeller Packed Box Design

Shaft Sleeve Repeller Plate

TECH-B

1140

TECH-B-4B Magnetic Drive Pumps

INTRODUCTION Environmental concerns and recurring mechanical seal problems have created a need for sealless pumps in the chemical and petrochemical industries. In some cases, more stringent regulations by the EPA, OSHA and local agencies are mandating the use of sealless pumps. One type of sealless pump is the magnetic drive pump which uses a permanent magnetic coupling to transmit torque to the impeller without the need for a mechanical seal for packing. PRINCIPLES OF OPERATION Magnetic drive pumps use a standard electric motor to drive a set of permanent magnets that are mounted on a carrier or drive assembly located outside of the containment shell. The drive magnet assembly is mounted on a second shaft which is driven by a standard motor. The external rotating magnetic field drives the inner rotor. The coaxial synchronous torque coupling consists of two rings of permanent magnets as shown in Fig. 1. A magnetic force field is established between the north and south pole magnets in the drive and driven assemblies. This provides the no slip or synchronous capability of the torque coupling. The magnetic field is shown as dashed lines and shaded areas in Fig. 3.

Fig. 1 Typical Magnetic Drive Pump Driven Magnet Drive Magnet Carrier Assembly Carrier Assembly Containment Shell

Bearing Frame Assembly

Bearings

A MOTOR (DRIVE) PUMP (DRIVEN)

Drive Magnet Assembly

Driven Magnet Assembly

Fig. 2. Coaxial Synchronous Magnetic Torque Coupling

Fig. 3

1141

TECH-B

Containment Shell Designs

The containment shell is the pressure containing barrier which is fitted between the drive and the driven magnet assembly. It must contain full working pressure of the pump, since it isolates the pumped liquid from the atmosphere. One-piece formed shells offer the best reliability, eliminating welds used for two-piece shells. Since the torque coupling magnetic force field must pass through the shell, it must be made of a non-magnetic material. Non-magnetic metals such as Hastelloy and 316SS are typical choices for the containment shell. The motion of the magnets past an electrically conductive containment shell produces eddy currents, which generate heat and must be removed by a process fluid recirculation circuit.

Sleeve and Thrust Bearings

The eddy currents also create a horsepower loss, which reduces the efficiency of the pump. Metals with low electrical conductivity have lower eddy current losses, providing superior pump efficiency. Hastelloy has a relatively low electrical conductivity and good corrosion resistance, thus is an excellent choice for metal containment shells. Electrically non-conductive materials such as plastic and ceramics are also good choices for containment shells, since the eddy current losses are totally eliminated. This results in pump efficiencies equal to conventionally sealed pumps. Plastic containment shells are generally limited to lower pressures and temperatures due to the limited strength of plastics.

Magnetic drive pumps utilize process lubricated bearings to support the inner drive rotor. These bearings are subject to the corrosive nature of the liquids being pumped, thus need to be made from corrosion resistant materials. Two commonly used materials are hard carbon and silicon carbide (SIC). Pure sintered SIC is superior to reaction bonded SIC, since reaction bonded SIC has free silicon left in the matrix, resulting in lower chemical resistance and lower strength.

Hard carbon against silicon carbide offers excellent service life for many chemical applications and also offers the advantage of short term operation in marginal lubrication conditions.

Silicon carbide against silicon carbide offers excellent service life for nearly all chemical applications. Its hardness, high thermal conductivity, and strength make it an excellent bearing material. Silicon carbide must be handled carefully to prevent chipping. Silicon carbide against silicon carbide has very limited capability in marginal lubrication conditions.

TECH-B

1142

TECH-B-5 Field Testing Methods

A. Determination of total head The total head of a pump can be determined by gauge readings as illustrated in Fig. 1. WATER hd Datum hs h h hd Pressure hs hs hd MERCURY Fig. 3 Manometer Indicating Pressure

Vacuum

Fig. 2 Manometer Indicating Vacuum

B. Measurement of capacity a.) Magnetic Flow Meter A calibrated magnetic flow meter is an accurate means of measuring flow in a pumping system. However, due to the expense involved, magnetic flow meters are only practical in small factory test loops and in certain process pumping systems where flow is critical. b.) Volumetric Measurement Pump capacity can be determined by weighing the liquid pumped or measuring its volume in a calibrated vessel. This is often practical when pumping into an accurately measured reservoir or tank, or when it is possible to use small containers which can be accurately weighed. These methods, however, are normally suited only to relatively small capacity systems. c.) Venturi Meter A venturi meter consists of a converging section, a short constricting throat section and then a diverging section. The object is to accelerate the fluid and temporarily lower its static pressure. The flow is then a function of the pressure differential between the full diameter line and the throat. Fig. 4 shows the general shape and flow equation. The meter coefficient is determined by actual calibration by the manufacturer and, when properly installed, the Venturi Meter is accurate to within plus or minus 1%. H 1 R4 C = Instrument Coefficient D1 = Entrance Diameter in Inches D2 = Throat Diameter in Inches R = D2/ D1 H = Differential Head in Inches = h1 h2 Q(GPM) = 5.67 CD22 h2 D2 D1

Fig. 1 Determination of Total Head From Gauge Readings Negative Suction Pressure: TDH = Discharge gauge reading converted to feet of liquid + vacuum gauge reading converted to feet of liquid + distance between point of attachment of vacuum gauge and the centerline of the discharge 2 2 gauge, h, in feet + Vd Vs 2g 2g

Positive Suction Pressure:

In using gauges when the pressure is positive or above atmospheric pressure, any air in the gauge line should be vented off by loosening the gauge until liquid appears. This assures that the entire gauge line is filled with liquid and thus the gauge will read the pressure at the elevation of the centerline of the gauge. However, the gauge line will be empty of liquid when measuring vacuum and the gauge will read the vacuum at the elevation of the point of attachment of the gauge line to the pipe line. These assumptions are reflected in the above definitions.

or TDH = Discharge gauge reading converted to feet of liquidpressure gauge reading in suction line converted to ft. of liquid + distance between center of discharge and suction gauges, h, in feet 2 2 + Vd Vs 2g 2g

The final term in the above definitions accounts for a difference in size between the suction and discharge lines. The discharge line is normally smaller than the suction line and thus the discharge velocity is higher. A higher velocity results in a lower pressure since the sum of the pressure head and velocity head in any flowing liquid remains constant. Thus, when the suction and discharge line sizes at the gauge attachment points are different, the resulting difference in velocity head must be included in the total head calculation.

D1

h1

Fig. 4 Venturi Meter d.) Nozzle

Manometers can also be used to measure pressure. The liquid used in a manometer is normally water or mercury, but any liquid of known specific gravity can be used. Manometers are extremely accurate for determining low pressures or vacuums and no calibration is needed. They are also easily fabricated in the field to suit any particular application. Figs. 2 & 3 illustrate typical manometer set ups.

A nozzle is simply the converging portion of a venturi tube with the liquid exiting to the atmosphere. Therefore, the same formula can be used with the differential head equal to the gauge reading ahead of the nozzle. Fig. 5 lists theoretical nozzle discharge flows.

1143

TECH-B

Theoretical Discharge of Nozzles in U.S. GPM

Head Lbs.
10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 175 200 250 300 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 175 200 250 300

Feet
23.1 34.6 46.2 57.7 69.3 80.8 92.4 103.9 115.5 127.0 138.6 150.1 161.7 173.2 184.8 196.3 207.9 219.4 230.9 242.4 254.0 265.5 277.1 288.6 300.2 311.7 323.3 334.8 346.4 404.1 461.9 577.4 692.8 23.1 34.6 46.2 57.7 69.3 80.8 92.4 103.9 115.5 127.0 138.6 150.1 161.7 173.2 184.8 196.3 207.9 219.4 230.9 242.4 254.0 265.5 277.1 288.6 300.2 311.7 323.3 334.8 346.4 404.1 461.9 577.4 692.8

Velocy of Disch. Feet per Sec.

38.6 47.25 54.55 61.0 66.85 72.2 77.2 81.8 86.25 90.4 94.5 98.3 102.1 105.7 109.1 112.5 115.8 119.0 122.0 125.0 128.0 130.9 133.7 136.4 139.1 141.8 144.3 146.9 149.5 161.4 172.6 193.0 211.2

Diameter of Nozzle in Inches

1

/16

1/8

3/16

1/4

3/8

1/2

5/8

3/4

7/8

1
94.5 116. 134. 149 164. 177. 189. 200. 211. 221. 231. 241. 250. 259. 267. 276. 284. 292. 299. 306. 314. 320. 327. 334. 341. 347. 354 360 366. 395. 423 473. 517. 1915 2345 2710 3025 3315 3580 3830 4055 4275 4480 4685 4875 5060 5240 5410 5575 5740 5900 6050 5900 6350 6490 6630 6760 6900 7030 7160 7280 7410 8000 8550 9570 10480 41/2

11/8
120 147 169 189 207 224 239 253 267 280 293 305 317 327 338 349 359 369 378 388 397 406 414 423 432 439 448 455 463 500 535 598 655 2365 2890 3340 3730 4090 4415 4725 5000 5280 5530 5790 6020 6250 6475 6690 6890 7090 7290 7470 7290 7840 8010 8180 8350 8530 8680 8850 8990 9150 9890 10580 11820 12940 5

11/4
148 181 209 234 256 277 296 313 330 346 362 376 391 404 418 431 443 456 467 479 490 501 512 522 533 543 553 562 572 618 660 739 808 2855 3490 4040 4510 4940 5340 5280 6050 6380 6690 6980 7270 7560 7820 8080 8320 8560 8800 9030 8800 9470 9680 9900 10100 10300 10490 10690 10880 11070 11940 12770 14290 15620 51/2

13/8
179 219 253 283 309 334 357 379 339 418 438 455 473 489 505 521 536 551 565 579 593 606 619 632 645 656 668 680 692 747 799 894 977 3405 4165 4810 5380 5895 6370 6380 7210 7600 7970 8330 8670 9000 9320 9630 9920 10210 10500 10770 10500 11300 11500 11800 12030 12290 12510 12730 12960 13200 14250 15220 17020 18610 6

0.37 0.45 0.52 0.58 0.64 0.69 0.74 0.78 0.83 0.87 0.90 0.94 0.98 1.01 1.05 1.08 1.11 1.14 1.17 1.20 1.23 1.25 1.28 1.31 1.33 1.36 1.38 1.41 1.43 1.55 1.65 1.85 2.02 213 260 301 336 368 398 425 451 475 498 521 542 563 582 602 620 638 656 672 689 705 720 736 751 767 780 795 809 824 890 950 1063 1163 11/2

1.48 1.81 2.09 2.34 2.56 2.77 2.96 3.13 3.30 3.46 3.62 3.77 3.91 4.05 4.18 4.31 4.43 4.56 4.67 4.79 4.90 5.01 5.12 5.22 5.33 5.43 5.53 5.62 5.72 6.18 6.61 7.39 8.08 289 354 409 458 501 541 578 613 647 678 708 737 765 792 818 844 868 892 915 937 960 980 1002 1022 1043 1063 1082 1100 1120 1210 1294 1447 1582 13/4

3.32 4.06 4.69 5.25 5.75 6.21 6.64 7.03 7.41 7.77 8.12 8.45 8.78 9.08 9.39 9.67 9.95 10.2 10.5 10.8 11.0 11.2 11.5 11.7 12.0 12.2 12.4 12.6 12.9 13.9 14.8 16.6 18.2 378 463 535 598 655 708 756 801 845 886 926 964 1001 1037 1070 1103 1136 1168 1196 1226 1255 1282 1310 1338 1365 1390 1415 1440 1466 1582 1691 1891 2070 2

5.91 7.24 8.35 9.34 10.2 11.1 11.8 12.5 13.2 13.8 14.5 15.1 15.7 16.2 16.7 17.3 17.7 18.2 18.7 19.2 19.6 20.0 20.5 20.9 21.3 21.7 22.1 22.5 22.9 24.7 26.4 29.6 32.4 479 585 676 756 828 895 957 1015 1070 1121 1172 1220 1267 1310 1354 1395 1436 1476 1512 1550 1588 1621 1659 1690 1726 1759 1790 1820 1853 2000 2140 2392 2615 21/4

13.3 16.3 18.8 21.0 23.0 24.8 26.6 28.2 29.7 31.1 32.5 33.8 35.2 36.4 37.6 38.8 39.9 41.0 42.1 43.1 44.1 45.1 46.0 47.0 48.0 48.9 49.8 50.6 51.5 55.6 59.5 66.5 72.8 591 723 835 934 1023 1106 1182 1252 1320 1385 1447 1506 1565 1619 1672 1723 1773 1824 1870 1916 1961 2005 2050 2090 2132 2173 2212 2250 2290 2473 2645 2955 3235 21/2

23.6 28.9 33.4 37.3 40.9 44.2 47.3 50.1 52.8 55.3 57.8 60.2 62.5 64.7 66.8 68.9 70.8 72.8 74.7 76.5 78.4 80.1 81.8 83.5 85.2 86.7 88.4 89.9 91.5 98.8 106. 118. 129. 714 874 1009 1128 1236 1335 1428 1512 1595 1671 1748 1819 1888 1955 2020 2080 2140 2200 2255 2312 2366 2420 2470 2520 2575 2620 2670 2715 2760 2985 3190 3570 3900 23/4

36.9 45.2 52.2 58.3 63.9 69.0 73.8 78.2 82.5 86.4 90.4 94.0 97.7 101. 104. 108. 111. 114. 117. 120. 122. 125. 128. 130. 133. 136. 138. 140. 143. 154. 165. 185. 202. 851 1041 1203 1345 1473 1591 1701 1802 1900 1991 2085 2165 2250 2330 2405 2480 2550 2625 2690 2755 2820 2885 2945 3005 3070 3125 3180 3235 3295 3560 3800 4250 4650 3

53.1 65.0 75.1 84.0 92.0 99.5 106. 113. 119. 125. 130. 136. 141. 146. 150. 155. 160. 164. 168. 172. 176. 180. 184. 188. 192. 195. 199. 202. 206. 222. 238. 266. 291. 1158 1418 1638 1830 2005 2168 2315 2455 2590 2710 2835 2950 3065 3170 3280 3375 3475 3570 3660 3750 3840 3930 4015 4090 4175 4250 4330 4410 4485 4840 5175 5795 6330 31/2

72.4 88.5 102. 114. 125. 135. 145. 153. 162. 169. 177. 184. 191. 198. 205. 211. 217. 223. 229. 234 240 245. 251. 256. 261. 266. 271. 275. 280. 302. 323. 362. 396. 1510 1850 2135 2385 2615 2825 3020 3200 3375 3540 3700 3850 4000 4135 4270 4440 4530 4655 4775 4655 5010 5120 5225 5340 5450 5550 5650 5740 5850 6310 6750 7550 8260 4

NOTE: The actual quantities will vary from these figures, the amount of variation depending upon the shape of nozzle and size of pipe at the point where the pressure is determined. With smooth taper nozzles the actual discharge is about 94% of the figures given in the tables.

38.6 47.25 54.55 61.0 66.85 72.2 77.2 81.8 86.25 90.4 94.5 98.3 102.1 105.7 109.1 112.5 115.8 119.0 122.0 125.0 128.0 130.9 133.7 136.4 139.1 141.8 144.3 146.9 149.5 161.4 172.6 193.0 211.2

TECH-B

Fig. 5

1144

e.) Orifice

An orifice is a thin plate containing an opening of specific shape and dimensions. The plate is installed in a pipe and the flow is a function of the pressure upstream of the orifice. There are numerous types of orifices available and their descriptions and applications are covered in the Hydraulic Institute Standards and the ASME Fluid Meters Report. Orifices are not recommended for permanent installations due to the inherent high head loss across the plate.

f.) Weir

A weir is particularly well suited to measuring flows in open conduits and can be adapted to extremely large capacity systems. For best accuracy, a weir should be calibrated in place. However, when this is impractical, there are formulas which can be used for the various weir configurations. The most common types are the rectangular contracted weir and the 90 V-notch weir. These are shown in Fig. 6 with the applicable flow formulas.

(6a) - Rectangular Weir With Complete End Contractions Q(G.P.M.) = 1495 H 3/2 (B-O.2H) H = Head in Feet Above Weir B = Crest Width in Feet

Q(G.P.M.) = 1140 H 5/2 H = Head in Feet Above Weir

(6b) - 90 V-Notch Weir

Fig. 31 Weirs

g.) Pitot tube

A pitot tube measures fluid velocity. A small tube placed in the flow stream gives two pressure readings: one receiving the full impact of the flowing stream reads static head + velocity head, and the other reads the static head only (Fig. 7). The difference between the two readings is the velocity head. The velocity and the flow are then determined from the following well known formulas. V= C 2ghv where C is a coefficient for the meter determined by calibration, and hv = velocity head,

Total head

Static head

Small holes on both sides of outer tube

Capacity = Area x Average Velocity

Since the velocity varies across the pipe, it is necessary to obtain a velocity profile to determine the average velocity. This involves some error but, when properly applied, a calibrated pitot tube is within plus or minus 2% accuracy.

Fig. 7 Pitot Tube

1145

TECH-B

TECH-B-6 Vibration Analysis

Vibration analysis equipment enables you to tell when "normal" vibration becomes "problem" vibration or exceeds acceptable levels. It may also allow you to determine the source and cause of the vibration, thus becoming an effective preventive maintenance and troubleshooting aid.

By analyzing the tabulated vibration data one or several causes may be found. Each must be checked, starting with the most likely cause or easiest to check.

A vibration analyzer measures the amplitude, frequency and phase of vibration. Also when vibration occurs at several frequencies, it separates one frequency from another so that each individual vibration characteristic can be measured. The vibration pickup senses the velocity of the vibration and converts it into an electrical signal. The analyzer receives this signal, converting it to the corresponding amplitude and frequency. The amplitude is measured in terms of peak-to-peak displacement in mils (1 mil = .001") and is indicated on the amplitude meter. Some instruments are equipped with a frequency meter which gives a direct readout of the predominant frequency of the vibration. Other instruments have tunable filters which allow scanning the frequency scale and reading amplitude at any particular frequency, all others being filtered out.

For example, assume the axial vibration is 50% or more of the radial vibration and the predominant frequency is the same as the RPM of the pump. The chart indicates probable misalignment or bent shaft. Coupling misalignment is probably the most common single cause of pump vibration and is one of the easiest to check. If after checking, the alignment proves to be good, then inspect for flange loading. Finally, check for a bent shaft. Cavitation in a pump can cause serious vibration. Vibration at random frequencies can also be caused by hydraulic disturbances in poorly designed suction or discharge systems. The use of vibration equipment in preventive maintenance involves keeping a vibration history on individual pieces of equipment in a plant. A form similar to that shown in Fig. 4 can be used to record the vibration data on a periodic routine basis. Abrupt changes are a sign of impending failure. A gradual increase in vibration can also be detected and corrective measures can be taken before it reaches a dangerous level.

A strobe light is used to determine the phase of vibration. It can be made to flash at the frequency of the vibration present or at any arbitrary frequency set on an internal oscillator.

A reference mark on a rotating part viewed under the strob light flashing at the vibration frequency may appear as a single frozen (or rotating) mark, or as several frozen (or rotating) marks. The number of marks viewed is useful in determining the source of the vibration. The location of the mark or marks is used in balancing rotating parts.

The first step in vibration analysis is to determine the severity of the vibration, then, if the vibration is serious, a complete set of vibration readings should be taken before attempting to analyze the cause. Fig. 1 is the general guide for horizontal centrifugal pumps as published by the Hydraulic Institute. The amplitudes shown are the overall maximum obtained without filtering to specific frequencies. Amplitudes at specific frequencies, such as vane pass frequency with multi-vane impellers, should be less than 75% of the unfiltered amplitudes allowed in Fig. 1 at the operating RPM. For horizontal non-clog and vertical submerged pumps, refer to Hydraulic Institute standards or pump manufacturer. Severity of vibration is a function of amplitude and pump speed; however, it should be noted that a change in severity over a period of time is usually a warning of impending failure. This change is often more important than vibration in the "slightly rough" or "rough" ranges which does not change with time. Complete pump vibration analysis requires taking vibration readings at each bearing in three planes (horizontal, vertical and axial). Readings at the pump suction and discharge flanges may also be useful in some cases.

Fig. 1 Acceptable field vibration limits for horizontal or vertical in-line pumps (Figures 1.107 to 1.109) - clear liquids
Reprinted from HYDRAULIC INSTITUTE STANDARDS. 1994 Edition, Copyright by Hydraulic Institute.

After all data has been tabulated, it can be analyzed to determine the most likely cause or causes of vibration and the identifying characteristics of each.

TECH-B

1146

Vibration Analysis Continued

Unbalance

Cause

Misalignment of coupling or bearings and bent shaft Bad Anti-friction bearings Mechanical looseness

Largest in radial direction. Proportional to unbalance

Amplitude

1 x RPM

Frequency

Single reference mark single, double, or triple

Phase

Unbalance

Remarks

Axial direction vibration 50% or more of radial

1 x RPM normally

Unsteady

2 x RPM Erratic or pulsing Disappears when power is turned off.

Very high. Several times RPM

Erratic Two reference marks. Slightly erratic.

Easily recognized by large axial vibration. Excessive flange loading can contribute to misalignment Largest high-frequency vibration near the bad bearing.

Bad drive belts Electrical Hydraulic forces

1 or 2 x synchronous frequency No. of impeller vanes x RPM

1, 2, 3 & 4 x RPM of belts

Unsteady

Single or rotating double mark

3600 or 7200 cps for 60 cycle current.

Use strobe light to freeze faulty belt.

Check grouting and bed plate bolting.

Rarely a cause of serious vibration

TECH-B-7 Vertical Turbine Pumps

Turbine Nomenclature
1. DATUM OR GRADE - The elevation of the surface from which the pump is supported. 2. STATIC LIQUID LEVEL - The vertical distance from grade to the liquid level when no liquid is being drawn from the well or source. 3. DRAWDOWN - The distance between the static liquid level and the liquid level when pumping at required capacity. 4. PUMPING LIQUID LEVEL - The vertical distance from grade to liquid level when pumping at rated capacity. Pumping liquid level equals static water level plus drawdown.

Fig. 3 Vibration Identification Chart

Fig. 4 Vibration Data Sheet

DISCHARGE LINE FRICTION LOSSES

HEAD ABOVE DISCHARGE GRADE STATIC LEVEL HEAD BELOW DISCHARGE DRAWDOWN

5. SETTING - The distance from grade to the top of the pump bowl assembly. 6. TPL (TOTAL PUMP LENGTH) - The distance from grade to lowest point of pump.

PUMP SETTING

SPECIFIED PUMP HEAD

TOTAL PUMP 8. COLUMN AND DISCHARGE HEAD FRICTION LOSS - Head LENGTH (TPL) loss in the pump due to friction in the column assembly and discharge head. Friction loss is measured in feet and is dependent upon column size, shaft size, setting, and discharge head size. Values given in appropriate charts in Data Section. 9. BOWL HEAD - Total head which the pump bowl assembly will deliver at the rated capacity. This is curve performance.

7. RATED PUMP HEAD - Lift below discharge plus head above discharge plus friction losses in discharge line. This is the head for which the customer is responsible and does not include any losses within the pump.

PUMPING LEVEL

SUBM.

10. BOWL EFFICIENCY- The efficiency of the bowl unit only. This value is read directly from the performance curve. BOWL HP = Bowl Head x Capacity 3960 x Bowl Efficiency

14. PUMP BRAKE HORSEPOWER - Sum of bowl horsepower plus shaft loss (and the driver thrust bearing loss under certain conditions).

11. BOWL HORSEPOWER- The horsepower - required by the bowls only to deliver a specified capacity against bowl head.

15. TOTAL PUMP EFFICIENCY (WATER TO WATER) -The efficiency of the complete pump, less the driver, with all pump losses taken into account. Efficiency = Specified Pump Head x Capacity 3960 x Brake Horsepower

12. TOTAL PUMP HEAD - Rated pump head plus column and discharge head loss. NOTE: This is new or final bowl head. 13. SHAFT FRICTION LOSS - The horsepower required to turn the lineshaft in the bearings. These values are given in appropriate table in Data Section.

17. SUBMERGENCE - Distance from liquid level to suction bell.

16. OVERALL EFFICIENCY (WIRE TO WATER) - The efficiency of the pump and motor complete. Overall efficiency = total pump efficiency x motor efficiency.

1147

TECH-B

Vertical Turbine Pumps - Calculating Axial Thrust

Under normal circumstances Vertical Turbine Pumps have a thrust load acting parallel to the pump shaft. This load is due to unbalanced pressure, dead weight and liquid direction change. Optimum selection of the motor bearing and correct determination of required bowl lateral for deep setting pumps require accurate knowledge of both the magnitude and direction (usually down) of the resultant of these forces. In addition, but with a less significant role, thrust influences shaft H.P. rating and shaft critical speeds. IMPELLER THRUST DEAD WEIGHT In addition to the impeller force, dead weight (shaft plus impeller weight less the weight of the liquid displaced) acts downward. On pumps with settings less than 50 feet, dead weight may be neglected on all but the most critical applications as it represents only a small part of the total force. On deeper setting pumps, dead weight becomes significant and must be taken into account. NOTE: We normally only take shaft weight into consideration as dead weight, the reason being that impeller weight less its liquid displacement weight is usually a small part of the total. SHAFT SLEEVES Finally, there can be an upward force across a head shaft sleeve or mechanical seal sleeve. In the case of can pumps with suction pressure, there can be an additional upward force across the impeller shaft area. Again, for most applications, these forces are small and can be neglected; however, when there is a danger of upthrusts or when there is high discharge pressure (above 600 psi) or high suction pressure (above 400 psi) these forces should be considered. MOTOR BEARING SIZING Generally speaking a motor for a normal thrust application has, as standard, a bearing adequate for shutoff thrust. When practical, motor bearings rated for shutoff conditions are preferred. For high thrust applications (when shutoff thrust exceeds the standard motor bearing rating) the motor bearing may be sized for the maximum anticipated operating range of the pump.

Impeller Thrust in the downward direction is due to the unbalanced discharge pressure across the eye area of the impeller. See diagram A. Counteracting this load is an upward force primarily due to the change in direction of the liquid passing through the impeller. The resultant of these two forces constitutes impeller thrust. Calculating this thrust using a thrust constant (K) will often produce only an approximate thrust value because a single constant cannot express the upthrust component which varies with capacity.

To accurately determine impeller thrust, thrust-capacity curves based on actual tests are required. Such curves now exist for the "A" Line. To determine thrust, the thrust factor "K" is read from the thrust-capacity curve at the required capacity and given RPM. "K" is then multiplied by the Total Pump Head (Final Lab Head) times Specific Gravity of the pumped liquid. If impeller thrust is excessively high, the impeller can usually be hydraulically balanced. This reduces the value of "K". Balancing is achieved by reducing the discharge pressure above the impeller eye by use of balancing holes and rings. See diagram B.

Should the pump operate below minimum flow for a short period of time, anti-friction bearings such as angular contact or spherical roller can handle the overload. It should be remembered, however, that bearing life is approximately inversely proportional to the cube of the load. Should the load double, motor bearing life will be cut to 1/8 of its original value. Although down thrust overloading is possible, the pump must never be allowed to operate in a continuous upthrust condition even for a short interval without a special motor bearing equipped to handle it. Such upthrust will fail the motor bearing. CALCULATING MOTOR BEARING LOAD As previously stated, for short setting non-hydraulic balanced pumps below 50 feet with discharge pressures below 600 psi and can pumps with suction pressures below 100 psi, only impeller thrust need be considered. Under these conditions: Motor Bearing Load (lbs.) Timp = KHL x SG Impeller Thrust (lbs.) K=Thrust factors (lbs./ft.) HL, = Lab Head (ft.) SG = Specific Gravity Where:

(A)

(B) Suction Pressure Discharge Pressure

NOTE:

Although hydraulic balancing reduces impeller thrust, it also decreases efficiency by one to five points by providing an additional path for liquid recirculation. Of even greater concern is that should the hydraulic balancing holes become clogged, (unclean fluids, fluids with solid content, intermittent services, etc.), the impeller thrust will increase and possibly cause the driver to fail. Hydraulically balanced impellers cannot be used in applications requiring rubber bowl bearings because the flutes on the inside diameter of the bearings provide an additional path to the top side of the impeller, thus creating an additional down thrust. Hydraulically balanced impellers should be used as a ''last resort" for those situations where the pump thrust exceeds the motor thrust bearing capabilities.

For more demanding applications, the forces which should be considered are impeller thrust plus dead weight minus any sleeve or shaft area force. Motor Bearing Load = Timp + Wt(1) sleeve force(2) shaft area force(3) =Tt In equation form:

TECH-B

1148

CALCULATING AXIAL THRUST - CONTINUED Shaft Dia (in) 1 1 /16 11/2

11 3 3

Shaft Dead Wt. (lbs/ft.) Open Closed Lineshaft Lineshaft 2.3 3.3 5.3 6.7 8.8 2.6 3.8 6.0 7.6

Shaft Area (in2) 1.1 1.8 .78

Sleeve Area (in) 1.0 1.1 1.1 1.5

(1) Wt.= Shaft Dead Wt. x Setting In Ft. (2) Sleeve Force=Sleeve area x Discharge pressure (3) Shaft Area Force = Shaft area x Suction pressure *Oil Lube shaft does not displace liquid above the pumping water level and therefore has a greater net weight. THRUST BEARING LOSS Thrust bearing loss is the loss of horsepower delivered to the pump at the thrust bearings due to thrust. In equation form: Tt LTB = .0075 BHP 100 1000

1 /16 115/16 2 /16

11.2

12.8

10.0

2.2

3.7

2.9

2.0

1.8

where:

( )(
= = = =

LTB BHP Tt

Vertical Turbine Bearing Material Data

Material Description 1.** 2.** 3. 4. 5. 6.** Standard Bronze (Federalloy III) 7% Tin/2-4% Zinc /85-89% Cu -50 to 180F Min. S. G. of 0.6 -50 to 300F All gravities -380 to 700F All gravities -50 to 250F All gravities 32 to 180F Min. S.G. of 0.6 32 to 150F Temperature and Specific Gravity Limits

Thrust bearing loss (HP) Brake horsepower Motor Bearing Load (Lbs.) Timp+ Wt(1) sleeve force(2) shaft area force(3)

(For specific applications where a given bearing material is specified and these limitations are exceeded, refer to factory.)
Remarks General purpose material for fresh/salt water light abrasive services up to 50 ppm. This is a non-leaded bronze material that will not dezincify in seawater because of low zinc content. Not suitable in ammonia, hydrogen sulfide and acetylene services. Good corrosion resistant material suitable for light abrasive services up to 10 ppm. Special materials available for temperatures beyond 300F. Good for low specific gravity fluids (e.g. ethane, propane, butane, ethylene) because the carbon is self-lubricating. Excellent corrosion resistant except for strong oxidizing solutions(1). Suitable for abrasive services up to 50 ppm. Special materials available for severe acid services. Good for low specific gravity fluids because the carbon is self-lubricating.

Resin Impregnated Carbon Metal (e.g. Nickel) impregnated carbon bearings Teflon (metal backed) 25% Graphite with 75% Teflon Cast Iron ASTM-A-48 CL30 (I. D. Electroless Nickel Coated)

Excellent corrosion resistant except for strong oxidizing solutions(1). Suitable for abrasive services up to 5 ppm. (Glass filled Teflon also available.) Limited applications - Call V.P.O.

Rubber (Nitrile Butadiene or Neoprene) with phenolic (3) or metal backing

First choice in abrasive fresh/salt water services up to 5000 ppm. Shafting should also be hardfaced for abrasive content above 100 ppm. Bearings must be wet prior to start-up if nonsubmerged ("dry column") length is greater than 50 ft. Do not use in oil, hydrocarbon services, and strong oxidizing agent(1). Contact the factory If the pumpage is other than fresh/salt water. Do not use for stuffing box or mechanical seal housing bushings; instead, use standard bronze for light abrasive service up to 50 ppm or hard faced bearing and shaft over 50 ppm. Do not use with hydraulically balanced impellers. Alternate for corrosive/abrasive services up to 5000 ppm. Coating or hardfacing material is typically chromium oxide. Contact factory if the bearing shell and/or coating need to be upgraded for better corrosion/abrasion resistance. Always use in combination with hardfaced shaft journals.

Limited to mildly caustic (2) and light abrasive services up to 10 ppm & some petroleum products (e.g. tar, heavy crude) with good lubricity.

7.** 8. 9. 10.

Stainless shell with hardfacing Boron diffusion coated 30% carbon fiber reinforced and compression molded PEEK Continuous carbon fiber reinforced PEEK Nitronic 60 Thordon

-100 to 300F Min. S.G. of 0.6 up to 400F -80 to 300F -80 to 600F

Recommended only for geothermal-brine services without the present of oxygen. Hardfaced coated surfaces typically in the range of Rc75. High temp. chemical vapor deposition (CVD). Hardness penetrates into various parent material (substrates), and will not flake, chip, or separate under severe applications (with no O2 presence). Good for services that are corrosive + high temp + abrasives up to 250 ppm. Good chemical resistance (not as good as carbon and Teflon.) Low coefficient of friction and impact/ thermal shock resistance. Not suitable for strong acids, halogens or hot solvents services. Difficult to machine.

11. 12.

** Denotes bearing materials which are included in Prism cost database. (1) Example of strong oxidizing agents: hydrochloric acid HCl, nitric acid HNO3, and sulfuric acid H2SO4(hot). (2) Common name for sodium hydroxide NaOH is lye or caustic soda. (3) Rubber with phenolic backing will be furnished unless other backing is specified by customer.

32 to 150F Min. S.G. of 0.6

-50 to 300F Min. S.G. of 0.6

Good for services that are corrosive + high temp + abrasives up to 1,000 ppm. Good chemical resistance (not as good as carbon and Teflon.) Low coefficient of friction and impact/ thermal shock resistance. Not suitable for strong acids, halogens or hot solvents services. Difficult to machine. This material is very difficult to install for high temperature (over 300F) service. For seawater service. Good for abrasives up to 50 ppm. For use ONLY with nitronic 50 shaft. Snap rings must be used. Absorbs water, tends to swell. Used at customer request only.

1149

TECH-B

TECH-B-8 Self Priming Pump System Guidelines

Self-priming pumps are inherently designed to allow the pump to re-prime itself typically under lift conditions. These pumps are very effective to the end user in that they will eliminate the need for foot valves, vacuum and ejector pumps which can become clogged or be impractical to use for prolonged or remote operation. Although the pump itself is designed to accomplish this task, it is important to understand the principle of how self-priming is achieved so that the piping system can be designed so as not to conflict with this function. A self-priming pump, by definition, is a pump which will clear its passages of air if it becomes air bound and resume delivery of the pumpage without outside attention. To accomplish this, a charge of

liquid sufficient to prime the pump must be retained in the casing (See Fig. A) or in an accessory priming chamber. When the pump starts, the rotating impeller creates a partial vacuum; air from the suction piping is then drawn into this vacuum and is entrained in the liquid drawn from the priming chamber. This air-liquid mixture is then pumped into the air separation chamber (within the casing) where the air is separated from the liquid with the air being expelled out the discharge piping (Fig. B) and the liquid returning to the priming chamber. This cycle is repeated until all of the air from the suction piping has been expelled and replaced by pumpage and the prime has been established (Fig. C).

Fig. A The following considerations should be made when designing a piping system for which a self-priming pump is to be used:

Fig. B

Fig. C

Care should be exercised to insure that adequate liquid is retained in the priming chamber. For outdoor/remote installations a heating element may be required to prevent freezing. For dirty services a strainer may be required to keep solids from accumulating in the priming chamber, thus displacing priming liquid.

The static lift and suction piping should be minimized to keep priming time to a minimum. Excessive priming time can cause liquid in the priming chamber to vaporize before prime is achieved. All connections in the suction piping should be leak-free as air could be sucked in, thus extending/compromising priming of the pump. (Pumps sealed with packing should be flushed to prevent air from being introduced.)

A priming bypass line (See Fig. D) should be installed so that back pressure is not created in the discharge piping during priming which would prevent the pump from priming itself. (Self-priming pumps are not good air compressors!)

Fig. D

The suction piping should be designed such that no high points are created where air can be trapped/accumulated which can prevent priming. Historically this has been problematic on top unloading of rail cars. (See Fig. E)

NOTE: Goulds Model 3796 self-priming process pump is outlined in Section CHEM 1-E.

TECH-B

1150

NOT RECOMMENDED

RECOMMENDED

TECH-B-9 Priming Time Calculations

To calculate the total priming time for a given system:

Fig. E Tank Car Unloading

Priming time data for each Model 3796 pump size and speed is displayed on the individual performance curves where priming time is plotted versus effective static lift for maximum, minimum and intermediate impeller diameters. This data is for suction piping of the same nominal diameter as the pump suction, i.e. 3" piping and 3" pump suction, and must be corrected for suction pipe diameters different from the pump suction and for suction pipe lengths greater than the effective static lift. 1. Select the correct size and speed pump from the performance curve for the given rating. 2. Calculate the NPSH Available for the system. The available NPSH must be equal to or greater than the NPSH Required by the selected pump at the rating point. where: P = Pressure on surface of liquid in feet absolute NPSHA = P - (Ls + Vp + hf) 5. Insert the priming time from Step 4 into the following formula to calculate the total system priming time: Priming Time - Seconds 2 PTT = PTLes x SPL x Dp Les Ds = Total system priming time.

where:

PTT

()

Ls = Maximum static lift in feet from free surface of the liquid to the centerline of the impeller. hf

SPL = Total suction pipe length above the free surface of the liquid in feet. Les Dp Ds = Effective static lift. = Nominal pipe diameter.

PTLes = Priming time in seconds for the effective static lift (Step 4.)

Vp = Vapor pressure of the liquid at maximum pumping temperature in feet absolute. = Suction pipe friction loss in feet at the required capacity.

= Nominal pump suction diameter.

Sample Priming Time Curve

3. Determine the effective static lift. where: Les = Effective static lift in feet. EFFECTIVE STATIC LIFT FT. (STATIC LIFT X S.G.) Les = Ls x Sp. Gr.

Sp. Gr. = Specific gravity of the liquid.

Ls = Maximum static lift in feet from free surface of the liquid to the centerline of the pump suction, or the highest point in the suction piping, whichever is greater.

4. Enter the priming time curve at the effective static lift calculated in Step 3. Proceed across to the impeller diameter selected for the specified rating and then downward to the bottom coordinate to determine the priming time (PTLes) to achieve the given lift.

PRIMING TIME SECONDS

1151

TECH-B

TECH-C-1 Friction Loss for Water Sched 40 Steel Pipe

1 U.S. /8 In. (0.269" I.D.) Gallons per V V2 hf Minute (Ft./Sec.) 2g (Ft./100 ft.) 0.2 1.13 0.020 2.72 0.4 2.26 0.079 16.2 0.6 3.39 0.178 33.8 0.8 4.52 0.317 57.4 1.0 5.65 0.495 87.0 1.5 8.48 1.12 188 2.0 11.3 1.98 324 2.5 3.0 3.5 4.0 4.5 5 6 7 8 9 10 12 14 1

Section TECH-C Water Data

V 1.23 1.85 2.47 3.08 4.62 6.17 7.17 9.25 10.79 12.33 13.87 15.42 2g 0.024 0.053 0.095 0.148 0.332 0.591 0.923 1.33 1.81 2.36 2.99 3.69 V2

/4 In. (0.364" I.D.) hf 3.7 7.6 12.7 19.1 40.1 69.0 105 148 200 259 326 398 V

/8 In. (0.493" I.D.) 2g 0.016 0.028 0.044 0.099 0.176 0.274 0.395 0.538 0.702 0.889 1.10 1.58 2.15 2.81 3.56 4.39 V2 hf 1.74 2.89 4.30 8.93 15.0 22.6 31.8 42.6 54.9 68.4 83.5 118 158 205 258 316

/2 In. (0.622" I.D.) 2g V2 hf

1.01 1.34 1.68 2.52 3.36 4.20 5.04 5.88 6.72 7.56 8.40 10.1 11.8 13.4 15.1 16.8

1.06 1.58 2.11 2.64 3.17 3.70 4.22 4.75 5.28 6.34 7.39 8.45 9.50 10.6 12.7 14.8

0.017 0.039 0.069 0.108 0.156 0.212 0.277 0.351 0.433 0.624 0.849 1.11 1.40 1.73 2.49 3.40

1.86 2.85 4.78 7.16 10.0 13.3 17.1 21.3 25.8 36.5 48.7 62.7 78.3 95.9 136 183

U.S. Gallons per Minute 0.2 0.4 0.6 0.8 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5 6 7 8 9 10 12 14

U.S. Gallons per Minute 4 5 6 7 8 9 10 12 14 16 18 20 25 30 35 40 45 50 60 70 80 90 100 120 140

/4 In. (0.824" I.D.) 2g 0.090 0.141 0.203 0.276 0.360 0.456 0.563 0.810 1.10 1.44 1.82 2.25 3.54 5.06 V2 4.21 6.32 8.87 11.8 15.0 18.8 23.0 32.6 43.5 56.3 70.3 86.1 134 187 hf V

1 In. (1.049" I.D.) 1.48 1.86 2.23 2.60 2.97 3.34 3.71 4.45 5.20 5.94 6.68 7.42 9.29 11.1 13.0 14.8 16.7 18.6 22.3 26.0 2g 0.034 0.053 0.077 0.105 0.137 0.173 0.214 0.308 0.420 0.548 0.694 0.857 1.34 1.93 2.62 3.43 4.33 5.35 7.71 10.5 V2 1.29 1.93 2.68 3.56 4.54 5.65 6.86 9.62 12.8 16.5 20.6 25.1 37.4 54.6 73.3 95.0 119 146 209 283 hf

1 1/4 In. (1.3880" I.D.) V 2g 0.026 0.035 0.046 0.058 0.071 0.103 0.140 0.183 0.232 0.286 0.448 0.644 0.879 1.14 1.45 1.79 2.57 3.50 4.58 5.79 7.15 10.3 V2 hf 0.70 0.93 1.18 1.46 1.77 2.48 3.28 4.20 5.22 6.34 9.66 13.6 18.5 23.5 29.5 36.0 51.0 68.8 89.2 112 138 197

1 1/2 In. (1.610" I.D.) V 2g V2

V 2.41 3.01 3.61 4.21 4.81 5.42 6.02 7.22 8.42 9.63 10.8 12.0 15.1 18.1

1.29 1.50 1.72 1.93 2.15 2.57 3.00 3.43 3.86 4.29 5.37 6.44 7.52 8.58 9.66 10.7 12.9 15.0 17.2 19.3 21.5 25.7

1.26 1.42 1.58 1.89 2.21 2.52 2.84 3.15 3.94 4.73 5.52 6.30 7.10 7.88 9.46 11.0 12.6 14.2 15.8 18.9 22.1

0.025 0.031 0.039 0.056 0.076 0.99 0.125 0.154 0.241 0.347 0.473 0.618 0.783 0.965 1.39 1.89 2.47 3.13 3.86 5.56 7.56

U.S. Gallons hf per Minute 4 5 6 7 0.56 8 0.69 9 0.83 10 1.16 12 1.53 14 1.96 16 2.42 18 2.94 20 4.50 25 6.26 30 8.38 35 10.8 40 13.5 45 16.4 50 23.2 60 31.3 70 40.5 80 51.0 90 62.2 100 88.3 120 119 140

TECH-C

1152

U.S. Gallons per Minute 30 35 40 50 60 80 100 120 140 160 180 200 220 240 260 280 300 350 400 500 600 700 800 1000

2 In. (2.067" I.D.) V 2.87 3.35 3.82 4.78 5.74 7.65 9.56 11.5 13.4 15.3 17.2 19.1 21.0 22.9 24.9 26.8 28.7 V2 2g 0.128 0.174 0.227 0.355 0.511 0.909 1.42 2.05 2.78 3.64 4.60 5.68 6.88 8.18 9.60 11.1 12.8 1.82 2.42 3.10 4.67 6.59 11.4 17.4 24.7 33.2 43.0 54.1 66.3 80.0 95.0 111 128 146 hf

21/2 In. (2.469" I.D.) V 2.01 2.35 2.68 3.35 4.02 5.36 6.70 8.04 9.38 10.7 12.1 13.4 14.7 16.1 17.4 18.8 20.1 23.5 26.8 33.5 V2 2g 0.063 0.085 0.112 0.174 0.251 0.447 0.698 1.00 1.37 1.79 2.26 2.79 3.38 4.02 4.72 5.47 6.28 8.55 11.2 17.4 0.75 1.00 1.28 1.94 2.72 4.66 7.11 10.0 13.5 17.4 21.9 26.7 32.2 38.1 44.5 51.3 58.5 79.2 103 160 hf V

3 In. (3.068" I.D.) V2 2g hf

3 1/2 In. (3.548" I.D.) V V2 2g hf

2.17 2.60 3.47 4.34 5.21 6.08 6.94 7.81 8.68 9.55 10.4 11.3 12.2 13.0 15.2 17.4 21.7 26.0 30.4 34.7

0.073 0.105 0.187 0.293 0.421 0.574 0.749 0.948 1.17 1.42 1.69 1.98 2.29 2.63 3.57 4.68 7.32 10.5 14.3 18.7

0.66 0.92 1.57 2.39 3.37 4.51 5.81 7.28 8.90 10.7 12.6 14.7 16.9 19.2 26.3 33.9 52.5 74.8 101 131

1.95 2.60 3.25 3.89 4.54 5.19 5.84 6.49 7.14 7.79 8.44 9.09 9.74 11.3 13.0 16.2 19.5 22.7 26.0 32.5

0.059 0.105 0.164 0.236 0.321 0.419 0.530 0.655 0.792 0.943 1.11 1.28 1.47 2.00 2.62 4.09 5.89 8.02 10.5 16.44

0.45 0.77 1.17 1.64 2.18 2.80 3.50 4.27 5.12 6.04 7.04 8.11 9.26 12.4 16.2 25.0 35.6 48.0 62.3 96.4

U.S. Gallons per Minute 30 35 40 50 60 80 100 120 140 160 180 200 220 240 260 280 300 350 400 500 600 700 800 1000

U.S. Gallons per Minute 140 160 180 200 240 280 320 360 400 450 500 600 700 800 900 1000 1200 1400 1600 1800 2000 2400 2800 3200 3600 4000

4 In. (4.026" I.D.) V 3.53 4.03 4.54 5.04 6.05 7.06 8.06 9.07 10.1 11.3 12.6 15.1 17.6 20.2 22.7 25.2 30.2 35.3 2g 0.193 0.253 0.320 0.395 0.569 0.774 1.01 1.28 1.58 2.00 2.47 3.55 4.84 6.32 8.00 9.87 14.2 19.3 V2 1.16 1.49 1.86 2.27 3.21 4.30 5.51 6.92 8.47 10.5 13.0 18.6 25.0 32.4 40.8 50.2 72.0 97.6 hf V

5 In. (5.047" I.D.) 2.25 2.57 2.89 3.21 3.85 4.49 5.13 5.77 6.41 7.23 8.02 9.62 11.2 12.8 14.4 16.0 19.2 22.5 25.7 28.8 32.1 2g 0.078 0.102 0.129 0.160 0.230 0.313 0.409 0.518 0.639 0.811 0.999 1.44 1.96 2.56 3.24 4.00 5.76 7.83 10.2 12.9 16.0 V2 0.38 0.49 0.61 0.74 1.03 1.38 1.78 2.22 2.72 3.42 4.16 5.88 7.93 10.2 12.9 15.8 22.5 30.4 39.5 49.7 61.0 hf V

6 In. (6.065" I.D.) 2g V2 hf V

8 In. (7.981" I.D.) 2g V2 hf

2.22 2.66 3.11 3.55 4.00 4.44 5.00 5.55 6.66 7.77 8.88 9.99 11.1 13.3 15.5 17.8 20.0 22.2 26.6 31.1 35.5

0.077 0.110 0.150 0.196 0.240 0.307 0.388 0.479 0.690 0.939 1.23 1.55 1.92 2.76 3.76 4.91 6.21 7.67 11.0 15.0 19.6

0.30 0.42 0.56 0.72 0.90 1.09 1.37 1.66 2.34 3.13 4.03 5.05 6.17 8.76 11.8 15.4 19.4 23.8 34.2 46.1 59.9

2.57 2.89 3.21 3.85 4.49 5.13 5.77 6.41 7.70 8.98 10.3 11.5 12.8 15.4 18.0 20.5 23.1 25.7

0.102 0.129 0.160 0.230 0.313 0.409 0.518 0.639 0.920 1.25 1.64 2.07 2.56 3.68 5.01 6.55 8.28 10.2

0.28 0.35 0.42 0.60 0.80 1.02 1.27 1.56 2.20 2.95 3.82 4.79 5.86 8.31 11.2 14.5 18.4 22.6

U.S. Gallons per Minute 140 160 180 200 240 280 320 360 400 450 500 600 700 800 900 1000 1200 1400 1600 1800 2000 2400 2800 3200 3600 4000

1153

TECH-C

U.S. Gallons per Minute 800 900 1000 1200 1400 1600 1800 2000 2500 3000 3500 4000 4500 5000 6000 7000 8000 9000 10,000 12,000 14,000 16,000 18,000 20,000

10 In. (10.020" I.D.) V 3.25 3.66 4.07 4.88 5.70 6.51 7.32 8.14 10.2 12.2 14.2 16.3 18.3 20.3 24.4 28.5 32.5 36.6 V2 2g 0.165 0.208 0.257 0.370 0.504 0.659 0.834 1.03 1.62 2.32 3.13 4.12 5.21 6.43 9.26 12.6 16.5 20.8 0.328 0.410 0.500 0.703 0.940 1.21 1.52 1.86 2.86 4.06 5.46 7.07 8.88 10.9 15.6 21.1 27.5 34.6 hf

12 In. (11.938" I.D.) V 2.58 2.87 3.44 4.01 4.59 5.16 5.73 7.17 8.60 10.0 11.5 12.9 14.3 17.2 20.1 22.9 25.8 28.7 34.4 40.1 V2 2g 0.103 0.128 0.184 0.250 0.327 0.414 0.511 0.799 1.15 1.55 2.04 2.59 3.19 4.60 6.26 8.17 10.3 12.8 18.3 25.0 hf 0.173 0.210 0.296 0.395 0.609 0.636 0.776 1.19 1.68 2.25 2.92 3.65 4.47 6.39 8.63 11.2 14.1 17.4 24.8 33.5 V

14 In. (13.124" I.D.) V2 2g 0.087 0.126 0.171 0.224 0.283 0.349 0.546 0.786 1.07 1.40 1.77 2.18 3.14 4.28 5.59 7.08 8.74 12.6 17.1 22.4 28.3 hf 0.131 0.185 0.247 0.317 0.395 0.483 0.738 1.04 1.40 1.81 2.27 2.78 3.95 5.32 6.90 8.7 10.7 15.2 20.7 26.8 33.9

16 In. (15.000" I.D.) V V2 2g hf

2.37 2.85 3.32 3.79 4.27 4.74 5.93 7.11 8.30 9.48 10.7 11.9 14.2 16.6 19.0 21.3 23.7 28.5 33.2 37.9 42.7

2.90 3.27 3.63 4.54 5.45 6.35 7.26 8.17 9.08 10.9 12.7 14.5 16.3 18.2 21.8 25.4 29.0 32.7 36.3

0.131 0.166 0.205 0.320 0.461 0.627 0.820 1.04 1.28 1.84 2.51 3.28 4.15 5.12 7.38 10.0 13.1 16.6 20.5

0.163 0.203 0.248 0.377 0.535 0.718 0.921 1.15 1.41 2.01 2.69 3.498 4.38 5.38 7.69 10.4 13.5 17.2 21.2

U.S. Gallons per Minute 800 900 1000 1200 1400 1600 1800 2000 2500 3000 3500 4000 4500 5000 6000 7000 8000 9000 10,000 12,000 14,000 16,000 18,000 20,000

U.S. Gallons per Minute 2000 3000 4000 5000 6000 8000 10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000 26,000 28,000 30,000 34,000 38,000 42,000 46,000 50,000

18 In. (16.876" I.D.) V 2.87 4.30 5.74 7.17 8.61 11.5 14.3 17.2 20.1 22.9 25.8 28.7 31.6 34.4 37.3 40.2 43.0 2g 0.128 0.288 0.512 0.799 1.15 2.05 3.20 4.60 6.27 8.19 10.4 12.8 15.5 18.4 21.6 25.1 28.8 V2 0.139 0.297 0.511 0.781 1.11 1.93 2.97 4.21 5.69 7.41 9.33 11.5 13.9 16.5 19.2 22.2 25.5 hf V 3.46 4.62 5.77 6.92 9.23 11.5 13.8 16.2 18.5 20.8 23.1 25.4 27.7 30.0 32.3 34.6 39.2 43.9

20 In. (18.812" I.D.) 2g 0.186 0.331 0.517 0.745 1.32 2.07 2.98 4.06 5.30 6.71 8.28 10.0 11.9 14.0 16.2 18.6 23.9 29.9 V2 hf 0.174 0.298 0.455 0.645 1.11 .70 2.44 3.29 4.26 5.35 6.56 7.91 9.39 11.0 12.7 14.6 18.7 23.2 V

24 In. (22.624" I.D.) 2g 0.158 0.247 0.356 0.633 0.989 1.42 1.94 2.53 3.21 3.96 4.79 5.70 6.69 7.76 8.91 11.4 14.3 17.5 20.9 24.7 V2 hf 0.120 0.181 0.257 0.441 0.671 0.959 1.29 1.67 2.10 2.58 3.10 3.67 4.29 4.96 5.68 7.22 9.00 11.0 13.2 15.5

3.19 3.99 4.79 6.38 7.98 9.58 11.2 12.8 14.4 16.0 17.6 19.2 20.7 22.3 23.9 27.1 30.3 33.5 36.7 39.9

U.S. Gallons per Minute 2000 3000 4000 5000 6000 8000 10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000 26,000 28,000 30,000 34,000 38,000 42,000 46,000 50,000

Reprinted from PIPE FRICTION MANUAL, Third Edition. Copyright 1961 by Hydraulic Institute.

TECH-C

1154

U.S. Gallons per Minute 5,000 6,000 7,000 8,000 9,000 10,000 12,000 14,000 16,000 18,000 20,000 25,000 30,000 35,000 40,000 45,000 50,000 60,000 70,000 80,000 90,000 100,000 120,000 140,000 160,000 180,000

30 In. V 2.43 2.91 3.40 3.89 4.37 4.86 5.83 6.80 7.77 8.74 9.71 12.1 14.6 17.0 19.4 21.9 24.3 29.1 34.0 38.9 V2 2g 0.0917 0.132 0.180 0.235 0.297 0.367 0.528 0.719 0.939 1.19 1.47 2.29 3.30 4.49 5.87 7.42 9.17 13.2 18.0 23.5 0.0535 0.0750 0.100 0.129 0.161 0.196 0.277 0.371 0.478 0.598 0.732 1.13 1.61 2.17 2.83 3.56 4.38 6.23 8.43 11.0 hf V

36 In. V2 2g hf V

42 In. V2 2g hf

2.52 2.84 3.15 3.78 4.41 5.04 5.67 6.30 7.88 9.46 11.03 12.6 14.1 15.8 18.9 22.1 25.2 28.4 31.5 37.8

0.0988 0.125 0.154 0.222 0.303 0.395 0.500 0.618 0.965 1.39 1.89 2.47 3.13 3.86 5.56 7.56 9.88 12.5 15.4 22.2

0.0442 0.0551 0.0670 0.0942 0.126 0.162 0.203 0.248 0.378 0.540 0.724 0.941 1.18 1.45 2.07 2.81 3.66 4.59 5.64 8.05

2.78 3.24 3.71 4.17 4.63 5.79 6.95 8.11 9.26 10.42 11.6 13.9 16.2 18.5 20.8 23.2 27.8 32.4 37.1 41.7

0.120 0.163 0.213 0.270 0.333 0.521 0.750 1.02 1.33 1.69 2.08 3.00 4.08 5.33 6.75 8.33 12.0 16.3 21.3 27.0

0.0441 0.0591 0.0758 0.0944 0.115 0.176 0.250 0.334 0.433 0.545 0.668 0.946 1.27 1.66 2.08 2.57 3.67 4.98 6.46 8.12

U.S. Gallons per Minute 5,000 6,000 7,000 8,000 9,000 10,000 12,000 14,000 16,000 18,000 20,000 25,000 30,000 35,000 40,000 45,000 50,000 60,000 70,000 80,000 90,000 100,000 120,000 140,000 160,000 180,000

U.S. Gallons per Minute 16,000 18,000 20,000 25,000 30,000 35,000 40,000 45,000 50,000 60,000 70,000 80,000 90,000 100,000 120,000 140,000 160,000 180,000 200,000 250,000 300,000 350,000

48 In. V 2.84 3.19 3.55 4.43 5.32 6.21 7.09 7.98 8.87 10.64 12.4 14.2 16.0 17.7 21.3 24.8 28.4 31.9 35.5 2g 0.125 0.158 0.195 0.305 0.440 0.598 0.782 0.989 1.221 1.76 2.39 3.13 3.96 4.89 7.03 9.57 12.5 15.8 19.5 V2 0.0391 0.0488 0.0598 0.0910 0.128 0.172 0.222 0.278 0.341 0.484 0.652 0.849 1.06 1.30 1.87 2.51 3.26 4.11 5.05 hf V

54 In. 2g 0.122 0.191 0.274 0.374 0.488 0.618 0.762 1.098 1.49 1.95 2.47 3.05 4.39 5.98 7.81 9.88 12.2 19.1 27.4 V2 hf 0.0333 0.0504 0.0713 0.0958 0.124 0.155 0.189 0.267 0.358 0.465 0.586 0.715 1.02 1.38 1.80 2.26 2.77 4.32 6.19 V

60 In. 2g V2 hf

2.80 3.50 4.20 4.90 5.60 6.30 7.00 8.40 9.81 11.21 12.6 14.0 16.8 19.6 22.4 25.2 28.0 35.0 42.0

2.84 3.40 3.97 4.54 5.11 5.67 6.81 7.94 9.08 10.21 11.3 13.6 15.9 18.2 20.4 22.7 28.4 34.0 39.7

0.125 0.180 0.245 0.320 0.405 0.500 0.720 0.980 1.28 1.62 2.00 2.88 3.92 5.12 6.48 8.00 12.5 18.0 24.5

0.0301 0.0424 0.0567 0.0730 0.0916 0.112 0.158 0.213 0.275 0.344 0.420 0.600 0.806 1.04 1.32 1.62 2.52 3.60 4.88

U.S. Gallons per Minute 16,000 18,000 20,000 25,000 30,000 35,000 40,000 45,000 50,000 60,000 70,000 80,000 90,000 100,000 120,000 140,000 160,000 180,000 200,000 250,000 300,000 350,000

1155

TECH-C

TECH-C-2 Resistance Coefficients for Valves and Fittings

BELL-MOUTH INLET OR REDUCER K = 0.05 REGULAR THREADED 45 ELL.

SQUARE EDGED INLET K = 0.5

LONG RADIUS FLANGED 45 ELL.

INWARD PROJECTING PIPE K = 1.0

THREADED RETURN BEND

NOTE: K DECREASES WITH INCREASING WALL THICKNESS OF PIPE AND ROUNDING OF EDGES

FLANGED RETURN BEND

REGULAR THREADED 90 ELL.

LINE FLOW THREADED TEE BRANCH FLOW

LONG RADIUS THREADED 90 ELL.

REGULAR FLANGED 90 ELL. FLANGED TEE

LINE FLOW

LONG RADIUS FLANGED 90 ELL.

BRANCH FLOW V2 h = K 2g g = 32.17 Feet/Second/Second K = Resistance Coefficient For Valve or Fitting

Chart 1 Where: h = Frictional Resistance in Feet of Liquid V = Average Velocity in Feet/Second in a Pipe of Corresponding Diameter

TECH-C

1156

SCREWED

BASKET STRAINER

GLOBE VALVE FLANGED

FOOT VALVE

SCREWED

GATE VALVE FLANGED COUPLINGS AND UNIONS

SCREWED

SWING CHECK VALVE

REDUCING BUSHING AND COUPLING V2 h=K 2 2g USED AS A REDUCER K = 0.05 2.0 SEE ALSO FIG. 3 USED AS INCREASER LOSS IS UP TO 40% MORE THAN THAT CAUSED BY A SUDDEN ENLARGEMENT

FLANGED

SCREWED

SUDDEN ENLARGEMENT

ANGLE VALVE FLANGED Chart 2 V2 h = K 2g

2g SEE ALSO EQUATION(5) IF A2 SO THAT V2 = 0 h = V12 FEET OF FLUID 2g

h = (V1 V2)2 FEET OF FLUID

Reprinted from PIPE FRICTION MANUAL, Third Edition, Copyright 1961 by Hydraulic Institute.

1157

TECH-C

TECH-C-3 Resistance Coefficients for Increasers and Diffusers

TECH-C-4 Resistance Coefficients for Reducers

Reprinted from PIPE FRICTION MANUAL, Third Edition. Copyright 1961 by Hydraulic Institute.

Reprinted from PIPE FRICTION MANUAL, Third Edition. Copyright 1961 by Hydraulic Institute.

TECH-C

1158

TECH-C-5 Properties of Water at Various Temperatures from 32 to 705.4F

Temp. F 32 40 45 50 55 Temp. C 0 4.4 7.2 10.0 12.8 SPECIFIC GRAVITY 60 F Reference 1.002 1.001 1.001 1.001 1.000 1.000 .999 .999 .998 .998 Wt. in Lb/Cu Ft 62.42 62.42 62.40 62.38 62.36 Vapor Pressure Psi Abs 0.0885 0.1217 0.1471 0.1781 0.2141 Vapor Pressure* Feet Abs. (At Temp.) 0.204 0.281 0.340 0.411 0.494 0.591 0.706 0.839 0.994 1.172 1.379 1.167 1.890 2.203 2.965

85 90 95 100 110 120 130 140 150 160

60 65 70 75 80

15.6 18.3 21.1 23.9 26.7

29.4 32.2 35.0 37.8 43.3 48.9 54.4 60.0 65.5 71.1

.997 .996 .995 .994 .992 .990 .987 .985 .982 .979

62.34 62.31 62.27 62.24 62.19 62.16 62.11 62.06 62.00 61.84 61.73 61.54 61.39 61.20 61.01

0.2653 0.3056 0.3631 0.4298 0.5069 0.5959 0.9682 0.8153 0.9492 1.275 1.692 2.223 2.889 3.718 4.741

320 340 360 380 400

220 240 260 280 300

170 180 190 200 212

420 440 460 480 500 520 540 560

160.0 171.1 182.2 193.3 204.4

104.4 115.6 126.7 137.8 148.9

76.7 82.2 87.7 93.3 100.0

215.6 226.7 237.8 248.9 260.0 271.1 282.2 293.3

.909 .898 .886 .874 .860

.956 .948 .939 .929 .919

.975 .972 .968 .966 .959

.847 .833 .818 .802 .786 .766 .747 .727

56.66 55.96 55.22 54.47 53.65

59.63 59.10 58.51 58.00 57.31

60.79 60.57 60.35 60.13 59.81

52.80 51.92 51.02 50.00 49.02 47.85 46.51 45.3 43.9 42.3 40.5 38.5

89.66 118.01 153.04 195.77 247.31

17.186 24.97 35.43 49.20 67.01

5.992 7.510 9.339 11.526 14.696

660 680 700 705.4

580 600 620 640

304.4 315.6 326.7 337.8

* Vapor pressure in feet of water (Abs.) Converted from PSIA using sp. gr. at temperature.

348.9 360.0 371.1 374.1

.704 .679 .650 .618

680.8 812.4 962.5 1133.1

308.83 381.59 466.9 566.1

841.17 1056.8 1317.8 1628.4 1998.2 2446.7 2972.5 3595.7 4345. 5242. 6341. 7689.

227.55 303.17 398.49 516.75 663.42

41.343 60.77 87.05 122.18 168.22

14.178 17.825 22.257 27.584 35.353

3.943 5.196 6.766 8.735 11.172

.577 .526 .435 .319

36.0 32.8 27.1 19.9

1325.8 1524.9 1786.6 2059.7

2365.4 2708.1 3039.7 3206.2

9458. 11878. 16407. 23187.

1159

TECH-C

TECH-C-6 Atmospheric Pressure, Barometric Reading and Boiling Point of Water at Various Altitudes
Altitude 1000 500 0 500 I I 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 8500 9000 9500 10000 15000 Feet Meters I 304.8 152.4 0.0 152.4 304.8 457.2 609.6 762.0 914.4 1066.8 1219.2 1371.6 1524.0 1676.4 1828.8 1981.2 2133.6 2286.0 2438.4 2590.8 2743.2 2895.6 3048.0 4572.0 Barometric Reading In. Hg. 31.0 30.5 29.9 29.4 28.9 28.3 27.8 27.3 26.8 26.3 25.8 25.4 24.9 24.4 24.0 23.5 23.1 22.7 22.2 21.8 21.4 21.0 20.6 16.9 Mm. Hg. 788 775 760 747 734 719 706 694 681 668 655 645 633 620 610 597 587 577 564 554 544 533 523 429 Atmospheric Pressure psia 15.2 15.0 14.7 14.4 14.2 13.9 13.7 13.4 13.2 12.9 12.7 12.4 12.2 12.0 11.8 11.5 11.3 11.1 10.9 10.7 10.5 10.3 10.1 8.3 Ft. Water 35.2 34.6 33.9 33.3 32.8 32.1 31.5 31.0 30.4 29.8 29.2 28.8 28.2 27.6 27.2 26.7 26.2 25.7 25.2 24.7 24.3 23.8 23.4 19.2 Boiling Pt. Of Water F 213.8 212.9 212.0 211.1 210.2 209.3 208.4 207.4 206.5 205.6 204.7 203.8 202.9 201.9 201.0 200.1 199.2 198.3 197.4 196.5 195.5 194.6 193.7 184.0

TECH-C

1160

TECH-C-7 Saturation: Temperatures Steam Data

Temp. Ft Abs. press. Specific Volume Lb Sat. Sat. Sq. In. Liquid Evap Vapor p vf vfg vg 0.08854 0.09995 0.12170 0.14752 0.17811 0.2563 0.3631 0.5069 0.6982 0.9492 1.2748 1.6924 2.2225 2.8886 3.718 4.741 5.992 7.510 9.339 11.526 14.123 14.696 17.186 20.780 24.969 29.825 35.429 41.858 49.203 57.556 67.013 89.66 118.01 153.04 195.77 247.31 308.83 381.59 466.9 566.1 680.8 812.4 962.5 1133.1 1325.8 1542.9 1786.6 2059.7 2365.4 2708.1 3093.7 3206.2 0.01602 0.01602 0.01602 0.01602 0.01603 0.01604 0.01606 0.01608 0.01610 0.01613 0.01617 0.01620 0.01625 0.01629 0.01634 0.01639 0.01645 0.01651 0.01657 0.01663 0.01670 0.01672 0.01677 0.01684 0.01692 0.01700 0.01709 0.01717 0.01726 0.01735 0.01745 0.01765 0.01787 0.01811 0.01836 0.01864 0.01894 0.01926 0.0196 0.0200 0.0204 0.0209 0.0215 0.0221 0.0228 0.0236 0.0247 0.0260 0.0278 0.0305 0.0369 0.0503 3306 2947 2444 2036.4 1703.2 1206.6 867.8 633.1 468.0 350.3 265.3 203.25 157.32 122.99 97.06 77.27 62.04 50.21 40.94 33.62 27.80 26.78 23.13 19.365 16.306 13.804 11.746 10.044 8.628 7.444 6.449 4.896 3.770 2.939 2.317 1.8447 1.4811 1.1979 0.9748 0.7972 0.6545 0.5385 0.4434 0.3647 0.2989 0.2432 0.1955 0.1538 0.1165 0.0810 0.0392 0 Enthalpy Sat. Liquid hf Evap hfg Sat. Vapor hg Sat. Liquid sf Entropy Sfg sfg Sat Vapor sg Temp Ft 32 35 40 45 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 212 220 230 240 250 260 270 280 290 300 320 340 360 380 400 420 440 460 480 500 520 540 560 580 600 620 640 660 680 700 705.4 3306 2947 2444 2036.4 1703.2 1206.7 867.9 633.1 468.0 350.4 265.4 203.27 157.34 123.01 97.07 77.29 62.06 50.23 40.96 33.64 27.82 26.80 23.15 19.382 16.323 13.821 11.763 10.061 8.645 7.461 6.446 4.914 3.788 2.957 2.335 1.8633 1.5000 1.2171 0.9944 0.8172 0.6749 0.5594 0.4649 0.3868 0.3217 0.2668 0.2201 0.1798 0.1442 0.1115 0.0761 0.0503 0.00 3.02 8.05 13.06 18.07 28.06 38.04 48.02 57.99 67.97 77.94 87.92 97.90 107.89 117.89 127.89 137.90 147.92 157.95 167.99 178.05 180.07 188.13 198.23 208.34 218.48 228.64 238.84 249.06 259.31 269.59 290.28 311.13 332.18 353.45 374.97 396.77 418.90 441.4 464.4 487.8 511.9 536.6 562.2 588.9 617.0 646.7 678.6 714.2 757.3 823.3 902.7 1075.8 1074.1 1071.3 1068.4 1065.6 1059.9 1054.3 1048.6 1042.9 1037.2 1031.6 1025.8 1020.0 1041.1 1008.2 1002.3 996.3 990.2 984.1 977.9 971.6 970.3 965.2 958.8 952.2 945.5 938.7 931.8 924.7 917.5 910.1 894.9 879.0 862.2 844.6 826.0 806.3 785.4 763.2 739.4 713.9 686.4 656.6 624.2 588.4 548.5 503.6 452.0 390.2 309.9 172.1 0 1075.8 1077.1 1079.3 1081.5 1083.7 1088.0 1092.3 1096.6 1100.9 1105.2 1109.5 1113.7 1117.9 1122.0 1126.1 1130.2 1134.2 1138.1 1142.0 1145.9 1149.7 1150.4 1153.4 1157.0 1160.5 1164.0 1167.3 1170.6 1173.8 1176.8 1179.7 1185.2 1190.1 1194.4 1198.1 1201.0 1203.1 1204.3 1204.6 1203.7 1201.7 1198.2 1193.2 1186.4 1177.3 1165.5 1150.3 1130.5 1104.4 1067.2 995.4 902.7 0.0000 0.0061 0.0162 0.0262 0.0361 0.0555 0.0745 0.0932 0.1115 0.1295 0.1471 0.1645 0.1816 0.1984 0.2149 0.2311 0.2472 0.2630 0.2785 0.2938 0.3090 0.3120 0.3239 0.3387 0.3531 0.3675 0.3817 0.3958 0.4096 0.4234 0.4369 0.4637 0.4900 0.5158 0.5413 0.5664 0.5912 0.6158 0.6402 0.6645 0.6887 0.7130 0.7374 0.7621 0.7872 0.8131 0.8398 0.8679 0.8987 0.9351 0.9905 1.0580 2.1877 2.1709 2.1435 2.1167 2.0903 2.0393 1.9902 1.9428 1.8972 1.8531 1.8106 1.7694 1.7296 1.6910 1.6537 1.6174 1.5822 1.5480 1.5147 1.4824 1.4508 1.4446 1.4201 1.3901 1.3609 1.3323 1.3043 1.2769 1.2501 1.2238 1.1980 1.1478 1.0992 1.0519 1.0059 0.9608 0.9166 0.8730 0.8298 0.7868 0.7438 0.7006 0.6568 0.6121 0.5659 0.5176 0.4664 0.4110 0.3485 0.2719 0.1484 0 2.1877 2.1770 2.1597 2.1429 2.1264 2.0948 2.0647 2.0360 2.0087 1.9826 1.9577 1.9339 1.9112 1.8894 1.8685 1.8485 1.8293 1.8109 1.7932 1.7762 1.7598 1.7566 1.7440 1.7288 1.7140 1.6998 1.6860 1.6727 1.6597 1.6472 1.6350 1.6115 1.5891 1.5677 1.5471 1.5272 1.5078 1.4887 1.4700 1.4513 1.4325 1.4136 1.3942 1.3742 1.3532 1.3307 1.3062 1.2789 1.2472 1.2071 1.1389 1.0580 32 35 40 45 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 212 220 230 240 250 260 270 280 290 300 320 340 360 380 400 420 440 460 480 500 520 540 560 580 600 620 640 660 680 700 705.4

1161

TECH-C

TECH-C-8 Saturation: Pressures Steam Data

Abs. press. Lb Temp. Sq. In. Liquid p t 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10 14.696 15 20 30 40 50 60 70 80 90 100 120 140 160 180 200 250 300 350 400 450 500 550 600 700 800 900 1000 1100 1200 1300 1400 1500 2000 2500 3000 3206.2 101.74 126.08 141.48 152.97 162.24 170.06 176.85 182.86 188.28 193.21 212.00 213.03 227.96 250.33 267.25 281.01 292.71 302.92 312.03 320.27 327.81 341.25 353.02 363.53 373.06 381.79 400.95 417.33 431.72 444.59 456.28 467.01 476.93 486.21 503.10 518.23 531.98 544.61 556.31 567.22 577.46 587.10 596.23 635.82 668.13 695.36 705.40 0.01614 0.01623 0.01630 0.01636 0.01640 0.01645 0.01649 0.01653 0.01656 0.01659 0.01672 0.01672 0.01683 0.01701 0.01715 0.01727 0.01738 0.01748 0.01757 0.01766 0.01774 0.01789 0.01802 0.01815 0.01827 0.01839 0.01865 0.01890 0.01913 0.0193 0.0195 0.0197 0.0199 0.0201 0.0205 0.0209 0.0212 0.0216 0.0220 0.0223 0.0227 0.0231 0.0235 0.0257 0.0287 0.0346 0.0503 Specific Volume Sat. Sat. Vapor Liquid vf vg 333.6 173.73 118.71 90.63 73.52 61.98 53.64 47.34 42.40 38.42 26.80 26.29 20.089 13.746 10.498 8.515 7.175 6.206 5.472 4.896 4.432 3.728 3.220 2.834 2.532 2.288 1.8438 1.5433 1.3260 1.1613 1.0320 0.9278 0.8422 0.7698 0.6554 0.5687 0.5006 0.4456 0.4001 0.3619 0.3293 0.3012 0.2765 0.1878 0.1307 0.0858 0.0503 Enthalpy Sat. Liquid hr Evap hfg Sat. Vapor hg Sat. Liquid sf Entropy Evap s fg Sat Vapor sg 69.70 93.99 109.37 120.86 130.13 137.96 144.76 150.79 156.22 161.17 180.07 181.11 196.16 218.82 236.03 250.09 262.09 272.61 282.02 290.56 298.40 312.44 324.82 335.93 346.03 355.36 376.00 393.84 409.69 424.0 437.2 449.4 460.8 471.6 491.5 509.7 526.6 542.4 557.4 571.7 585.4 598.7 611.6 671.7 730.6 802.5 902.7 1036.3 1022.2 1031.2 1006.4 1001.0 996.2 992.1 988.5 985.2 982.1 970.3 969.7 960.1 945.3 933.7 924.0 915.5 907.9 901.1 894.7 888.8 877.9 868.2 859.2 850.8 843.0 825.1 809.1 794.2 780.5 767.4 755.0 743.1 731.6 709.7 688.9 668.8 649.4 630.4 611.7 593.2 574.7 556.3 463.4 360.5 217.8 0 1106.0 1116.2 1122.6 1127.3 1131.1 1134.2 1136.9 1139.3 1141.4 1143.3 1150.4 1150.8 1156.3 1164.1 1169.7 1174.1 1177.6 1180.6 1183.1 1185.3 1187.2 1190.4 1193.0 1195.1 1196.9 1198.4 1201.1 1202.8 1203.9 1204.5 1204.6 1204.4 1203.9 1203.2 1201.2 1198.6 1195.4 1191.8 1187.8 1183.4 1178.6 1173.4 1167.9 1135.1 1091.1 1020.3 902.7 0.1326 0.1749 0.2008 0.2198 0.2347 0.2472 0.2581 0.2674 0.2759 0.2835 0.3120 0.3135 0.3356 0.3680 0.3919 0.4110 0.4270 0.4409 0.4531 0.4641 0.4740 0.4916 0.5069 0.5204 0.5325 0.5435 0.5676 0.5879 0.6056 0.6214 0.6356 0.6487 0.6608 0.6720 0.6925 0.7108 0.7275 0.7430 0.7575 0.7711 0.7840 0.7963 0.8082 0.8619 0.9126 0.9731 1.0580 1.8456 1.7451 1.6855 1.6427 1.6094 1.5820 1.5586 1.5383 1.5203 1.5041 1.4446 1.4115 1.3962 1.3313 1.2844 1.2474 1.2168 1.1906 1.1676 1.1471 1.1286 1.0962 1.0682 1.0436 1.0217 1.0018 0.9588 0.9225 0.8910 0.8630 0.8378 0.8147 0.7934 0.7734 0.7371 0.7054 0.6744 0.6467 0.6205 0.5956 0.5719 0.5491 0.5269 0.4230 0.3197 0.1885 0 1.9782 1.9200 1.8863 1.8625 1.8441 1.8292 1.8167 1.8057 1.7962 1.7876 1.7566 1.7549 1.7319 1.6993 1.6763 1.6585 1.6438 1.6315 1.6207 1.6112 1.6026 1.5878 1.5751 1.5640 1.5542 1.5453 1.5263 1.5104 1.4966 1.4844 1.4734 1.4634 1.4542 1.4454 1.4296 1.4235 1.4020 1.3897 1.3780 1.3667 1.3559 1.3454 1.3351 1.2849 1.2322 1.1615 1.0580 Internal Energy Sat. Liquid Evap uf ufg 69.70 93.98 109.36 120.85 130.12 137.94 144.74 150.77 156.19 161.14 180.02 181.06 196.10 218.73 235.90 249.93 261.90 272.38 281.76 290.27 298.08 312./05 324.35 335.39 345.42 354.68 375.14 392.79 408.55 422.6 435.5 447.6 458.8 469.4 488.8 506.6 523.1 538.4 552.9 566.7 580.0 592.7 605.1 662.2 717.3 783.4 872.9 974.6 957.9 947.3 939.3 933.0 927.5 922.7 918.4 914.6 911.1 897.5 896.7 885.8 869.1 856.1 845.4 836.0 827.8 820.3 813.4 807.1 795.6 785.2 775.8 767.1 759.0 740.7 724.3 709.6 695.9 683.2 671.0 659.4 648.3 627.5 607.8 589.0 571.0 553.5 536.3 519.4 502.7 486.1 403.4 313.3 189.3 0 1044.2 1051.9 1056.7 1060.2 1063.1 1065.4 1067.4 1069.2 1070.8 1072.2 1077.5 1077.8 1081.9 1087.8 1092.0 1095.3 1097.9 1100.2 1102.1 1103.7 1105.2 1107.6 1109.6 1111.2 1112.5 1113.7 1115.8 1117.1 1118.0 1118.5 1118.7 1118.6 1118.2 1117.7 1116.3 1114.4 1112.1 1109.4 1106.4 1103.0 1099.4 1095.4 1091.2 1065.6 1030.6 972.7 872.9 Abs. Sat press. Lb Vapor Sq. In. ug P 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10 14.696 15 20 30 40 50 60 70 80 90 100 120 140 160 180 200 250 300 350 400 450 500 550 600 700 800 900 1000 1100 1200 1300 1400 1500 2000 2500 3000 3206.2

TECH-C

1162

TECH-D-1 Viscosity

Section TECH-D Properties of Liquids

The viscosity of a fluid is that property which tends to resist a shearing force. It can be thought of as the internal friction resulting when one layer of fluid is made to move in relation to another layer. Consider the model shown in Fig. 1, which was used by Isaac Newton in first defining viscosity. It shows two parallel planes of fluid of area A separated by a distance dx and moving in the same direction at different velocities V1 and V2.

Fig. 1 The velocity distribution will be linear over the distance dx, and dv experiments show that the velocity gradient, dx , is directly f proportional to the force per unit area, a .

Fig. 3 shows graphically the three most common types of NonNewtonian liquids. Group A shows a decreasing viscosity with an increasing rate of shear. This is known as a pseudo-plastic material. Examples of this type are grease, molasses, paint, soap, starch, and most emulsions. They present no serious pumping problems since they tend to thin out with the high rates of shear present in a pump. Group B shows a dilatant material or one in which the viscosity increases with an increasing rate of shear. Clay slurries and candy compounds are examples of dilatant liquids. Pumps must be selected with extreme care since these liquids can become almost solid if the shear rate is high enough. The normal procedure would be to oversize the pump somewhat and open up the internal clearances in an effort to reduce the shear rate. Group C shows a plastic material, The viscosity decreases with increasing rate of shear. However, a certain force must be applied before any movement is produced. This force is called the yield value of the material. Tomato catsup is a good example of this type of material. It behaves similar to a pseudo-plastic material from a pumping standpoint. Group A Group B Group C

Fig. 2 Newtonian Liquid

dv The velocity gradient, dx , describes the shearing experienced by the intermediate layers as they move with respect to each other. Therefore, it can be called the "rate of shear." S. Also, the F force per unit area, A , can be simplified and called the "shear force" or "shear stress," F. With these simplified terms, viscosity can be defined as follows: F= nXS Viscosity = n = F = shear stress S rate of shear

f = n x dv Where n is constant for a given liquid and A dx is called its viscosity.

Isaac Newton made the assumption that all materials have, at a given temperature, a viscosity that is independent of the rate of shear. In other words, a force twice as large would be required to move a liquid twice as fast. Fluids which behave this way are called Newtonian fluids. There are, of course, fluids which do not behave this way, in other words their viscosity is dependent on the rate of shear. These are known as Non-Newtonian fluids. Fig. 2 shows graphically the relationships between shear Stress (F,) rate of shear (S,) and viscosity (n) for a Newtonian liquid. The viscosity remains constant as shown in sketch 2, and in absolute units, the viscosity is the inverse slope of the line in sketch 1. Water and light oils are good examples of Newtonian liquids.

Pseudo-Plastic

Dilitant Fig. 3 Non-Newtonian Liquids

Plastic

1163

TECH-D

The viscosity of some Non-Newtonian liquids is dependent upon time as well as shear rate. In other words, the viscosity at any particular time depends upon the amount of previous agitation or shearing of the liquid. A liquid whose viscosity decreases with time at a given shear rate is called a thixotropic liquid. Examples are asphalts, glues, molasses, paint, soap, starch, and grease. Liquids whose viscosity increases with time are called rheopectic liquids, but they are seldom encountered in pumping applications.

viscosity. The basic unit of kinematic viscosity is the stoke which is equal to a square centimeter per second in the Metric system. The corresponding English unit is square foot per second. The centistoke which is one-hundredth of a stoke is normally used in the charts. The following formula is used to obtain the kinematic viscosity when the dynamic or absolute viscosity is known: centistokes = centipoise sp. gr.

There are two basic viscosity parameters: dynamic (or absolute) viscosity and kinematic viscosity. Dynamic viscosities are given in terms of force required to move a unit area a unit distance. This is usually expressed in pound-seconds per square foot in the English system which is equal to slugs per foot-second. The Metric system is more commonly used, however, in which the unit is the dyne-second per square centimeter called the Poise. This is numerically equal to the gram per centimeter-second. For convenience, numerical values are normally expressed in centipoise, which are equal to onehundredth of a poise. Most pipe friction charts and pump correction charts list kinematic

There are numerous types of viscometers available for determining liquid viscosities, most of which are designed for specific liquids or viscosity ranges. The Saybolt viscometers are probably the most widely used in the United States. The Saybolt Universal Viscometer measures low to medium viscosity, and the Saybolt Furol Viscometer measures high viscosities. The corresponding units are the SSU (Seconds Saybolt Universal) and the SSF (Seconds Saybolt Furol). These units are found on most pipe friction and pump correction charts in addition to centistokes. A conversion chart for these and other units is shown in Figs. 4A and 4B.

TECH-D-2A Viscosity Conversion Table

The following table will give an approximate comparison of various viscosity ratings so that if the viscosity is given in terms other than Saybolt Universal, it can be translated quickly by following horizontally to the Saybolt Universal column. Seconds Kine- Seconds Seconds Seconds Saybolt matic Saybolt RedRedDegrees Degrees Seconds Seconds Seconds Seconds Seconds Seconds Universal Viscosity Furol wood 1 wood 2 Engler Barbey Parlin Parlin Parlin Parlin Ford Ford ssu Centissf (Stan(AdmirCup #7 Cup #10 Cup #15 Cup #20 Cup #3 Cup #4 stokes* dard) alty) 31 35 40 50 1.00 2.56 4.30 7.40 29 32.1 36.2 44.3 5.10 5.83 1.00 1.16 1.31 1.58 6200 2420 1440 838 618 483 404 348 -

100 150 200 250

60 70 80 90

8000 9000 10000

4000 5000 6000 7000

1500 2000 2500 3000

700 800 900 1000

300 400 500 600

65.0 87.60 110.0 132 154 176 198 220

20.6 32.1 43.2 54.0

10.3 13.1 15.7 18.2

15.24 19.30 23.5 28.0 32.5 41.9 51.6 61.4

12.95 13.70 14.44

85.6 128 170 212 254 338 423 508

52.3 60.9 69.2 77.6

10.12 14.48 18.90 23.45 28.0 37.1 46.2 55.4

6.77 7.60 8.44 9.30

15000 20000

1760 1980 2200 3300 4400

880 1100 1320 1540

330 440 550 660

71.1 81.0 91.0 100.7 150 200 250 300

800 900 1000

400 500 600 700

1500 2000

13700 18400

6770 7620 8460

3380 4230 5080 5920

1270 1690 2120 2540

592 677 762 896

138.2 184.2 230 276 368 461 553 645

64.6 73.8 83.0 92.1

8.79 11.70 14.60 17.50

3.02 4.48 5.92 7.35

1.88 2.17 2.45 2.73

20.45 23.35 26.30 29.20 43.80 58.40 73.0 87.60

95 70.8 56.4 47.0

307 195 144 114

40.3 35.2 31.3 28.2 18.7 14.1 11.3 9.4

52.5 66 79 92 106 120 135 149 -

40 46

15 21 25 30

737 829 921 -

233.5 263 292 438 584

117.0 146 175 204.5

3.52 3.13 2.82 2.50 1.40

7.05 5.64 4.70 4.03

344 387 430 650 860

172 215 258 300

65 86 108 129

35 39 41 43

9.0 9.8 10.7 11.5

6.0 7.2 7.8 8.5

3.0 3.2 3.4 3.6

15.2 19.5 24 28.5 37 47 57 67

3.9 4.1 4.3 4.5 6.3 7.5 9 11 14 18 22 25

30 42 50 58

Fig. 4A

TECH-D

Reprinted from PIPE FRICTION MANUAL. Third Edition Copyright 1961 by Hydraulic Institute

147 203

76 86 96

29 32 35

53 70

1280 1715

680 780 850

337 425 520 600

132 172 218 258

67 74 82 90

20 28 34 40

860 1150

465 520 575

230 290 350 410

90 118 147 172

45 50 57 62

1164

When the Metric System terms centistokes and centipoises are used, the density is numerically equal to the specific gravity. Therefore, the following expression can be used which will be sufficiently accurate for most calculations: *Kinematic Viscosity (in centistokes) = Absolute Viscosity (in centipoises) Specific Gravity

*Kinematic Viscosity (in centistokes) = Absolute Viscosity (in centipoises) Density

For values of 70 centistokes and above, use the following conversion: Above the range of this table and within the range of the viscosimeter, multiply the particular value by the following approximate factors to convert to SSU: Saybolt Furol Redwood Standard Redwood Admiralty Engler Degrees Viscosimeter Factor 10. 1.095 10.87 34.5 Parlin cup #15 Parlin cup #20 Ford cup #4 Viscosimeter Factor 98.2 187.0 17.4 SSU = centistokes x 4.635

TECH-D-2B Viscosity Conversion Table

Seconds Kine- Approx. Approx. Saybolt matic Seconds Gardner Universal Viscosity Mac Holt ssu Centi- Michael Bubble stokes* 31 35 40 50 60 70 80 90 100 150 200 250 300 400 500 600 700 800 900 1000 1500 2000 2500 3000 4000 5000 6000 7000 8000 9000 10000 15000 20000 1.00 2.56 4.30 7.40 10.3 13.1 15.7 18.2 20.6 32.1 43.2 54.0 65.0 87.0 110.0 132 154 176 198 220 330 440 550 660 880 1100 1320 1540 1760 1980 2200 3300 4400 125 145 165 198 225 270 320 370 420 470 515 570 805 1070 1325 1690 2110 2635 3145 3760 4170 4700 5220 7720 10500 A A B C D F G H I M Q T U V W X Y Z Z2 Z3

When the English System units are used, the density must be used rather than the specific gravity.

The following table will give an approximate comparison of various viscosity ratings so that if the viscosity is given in terms other than Saybolt Universal, it can be translated quickly by following horizontally to the Saybolt Universal column. Seconds Seconds Seconds Seconds Seconds Seconds Seconds Approx. Seconds Zahn Zahn Zahn Zahn Zahn Demmier Demmier Seconds Pratt Cup #1 Cup #2 Cup #3 Cup #4 Cup #5 Cup #1 Cup #10 Stormer and 100 gpm Lambert Load "F" 38 47 54 62 73 90 18 20 23 26 29 37 46 55 63 72 80 88 22.5 24.5 27 29 40 51 63 75 18 20 28 34 41 48 63 77 13 18 24 29 33 43 50 65 75 86 96 1.3 2.3 3.2 4.1 4.9 5.7 6.5 10.0 13.5 16.9 20.4 27.4 34.5 41 48 55 62 69 103 137 172 206 275 344 413 481 550 620 690 1030 1370 1.0 1.4 1.7 2.0 2.7 3.5 4.1 4.8 5.5 6.2 6.9 10.3 13.7 17.2 20.6 27.5 34.4 41.3 48 55 62 69 103 137 2.6 3.6 4.6 5.5 6.4 7.3 11.3 15.2 19 23 31 39 46 54 62 70 77 116 154 193 232 308 385 462 540 618 695 770 1160 1540 7 8 9 9.5 10.8 11.9 12.4 16.8 22 27.6 33.7 45 55.8 65.5 77 89 102 113 172 234

Fig. 4B Above the range of this table and within the range of the viscosimeter, multiply the particular value by the following approximate factors to convert to SSU: Viscosimeter Mac Michael Demmier #1 Demmier #10 Stormer Factor 1.92 (approx.) 14.6 146. 13. (approx.)

1165

TECH-D

TECH-D-3 Determination of Pump Performance When Handling Viscous Liquids

The performance of centrifugal pumps is affected when handling viscous liquids. A marked increase in brake horsepower, a reduction in head, and some reduction in capacity occur with moderate and high viscosities. Fig. 5 provides a means of determining the performance of a conventional centrifugal pump handling a viscous liquid when its performance on water is known. It can also be used as an aid in selecting a pump for a given application. The values shown in Fig. 5 are averaged from tests of conventional single stage pumps of 2-inch to 8inch size, handling petroleum oils. The correction curves are, therefore, not exact for any particular pump. When accurate information is essential, performance tests should be conducted with the particular viscous liquid to be handled.

Reprinted from HYDRAULIC INSTITUTE STANDARDS. Twelfth Edition. Copyright 1969 by Hydraulic Institute.

Limitations on Use of Viscous Liquid Performance Correction Chart

Reference is made to Fig. 5. This chart is to be used only within the scales shown. Do not extrapolate. Use only for pumps of conventional hydraulic design, in the normal operating range, with open or closed impellers. Do not use for mixed flow or axial flow pumps or for pumps of special hydraulic design for either viscous or non-uniform liquids. Use only where adequate NPSH is available in order to avoid the effect of cavitation. Use only on Newtonian (uniform) liquids. Gels, slurries, paper stock and other non-uniform liquids may produce widely varying results, depending on the particular characteristics of the liquids.

Fig. 5 Performance Correction Chart

TECH-D

1166

Symbols and Definitions Used in Determination of Pump Performance When Handling Viscous Liquids. These symbols and definitions are: Qvis Hvis Evis bhpvis QW HW sp gr CQ CH CE = Viscous Capacity, gpm The capacity when pumping a viscous liquid. = Viscous Head, feet The head when pumping a viscous liquid. = Viscous Efficiency, per cent The efficiency when pumping a viscous liquid. = Viscous Brake Horsepower The horsepower required by the pump for the viscous conditions. = Water Capacity, gpm The capacity when pumping water. = Water Head, feet The head when pumping water. = Specific Gravity = Capacity correction factor = Head correction factor = Efficiency correction factor

The viscous efficiency and the viscous brake horsepower may then be calculated. This procedure is approximate as the scales for capacity and head on the lower half of Fig. 5 are based on the water performance. However, the procedure has sufficient accuracy for most pump selection purposes. Where the corrections are appreciable, it is desirable to check the selection by the method described below.

EXAMPLE. Select a pump to deliver 750 gpm at 100 feet total head of a liquid having a viscosity of 1000 SSU and a specific gravity of 0.90 at the pumping temperature. Enter the chart (Fig. 5) with 750 gpm, go up to 100 feet head, over to 1000 SSU, and then up to the correction factors: CQ CH CE Qw Hw = = = = = 0.95 0.92 (for 1.0 Qnw) 0.635 750 = 790 gpm 0.95 100 = 108.8 109 feet head 0.92

1.0 Qw

The following equations are used for determining the viscous performance when the water performance of the pump is known: Qvis = CQ X Qw = CH x Hw = CE x Ew

= Water Capacity at which maximum efficiency is obtained.

Select a pump for a water capacity of 790 gpm at 109 feet head. The selection should be at or close to the maximum efficiency point for water performance. If the pump selected has an efficiency on water of 81 per cent at 790 gpm, then the efficiency for the viscous liquid will be as follows: The brake horsepower for pumping the viscous liquid will be: bhpvis = 750 x 100 x 0.90 = 33.1 hp 3960 x 0.515 Evis = 0.635 x 81% = 51.5 per cent

Hvis Evis

For performance curves of the pump selected, correct the water performance as shown below. Instructions for Determining Pump Performance on a Viscous Liquid When Performance on Water is Known Given the complete performance characteristics of a pump handling water, determine the performance when pumping a liquid of a specified viscosity.

CQ, CH and CE are determined from Fig. 5 which is based on the water performance.

bhpvis = Qvis x Hvis x sp gr 3960 x Evis

The following equations are used for approximating the water performance when the desired viscous capacity and head are given and the values of CQ and CH must be estimated from Fig. 5 using Qvis and Hvis, as: QW(approx.) = Qvis CQ HW(approx.) = Hvis CH

From the efficiency curve, locate the water capacity (1.0 x Qw) at which maximum efficiency is obtained. From this capacity, determine the capacities (0.6 x Qw). (0.8 x Qw) and (1.2 x Qw). Enter the chart at the bottom with the capacity at best efficiency (1.0 x Qw), go upward to the head developed (in one stage) (Hw) at this capacity, then horizontally (either left or right) to the desired viscosity, and then proceed upward to the various correction curves. Read the values of (CE) and (CQ), and of (CH) for all four capacities.

Instructions for Preliminary Selection of a Pump for a Given Head-Capacity-Viscosity Condition Given the desired capacity and head of the viscous liquid to be pumped and the viscosity and specific gravity at the pumping temperature, Fig. 5 can be used to find approximate equivalent capacity and head when pumping water.

Multiply each head by its corresponding head correction factor to obtain the corrected heads. Multiply each efficiency value by (CE) to obtain the corrected efficiency values which apply at the corresponding corrected capacities. Plot corrected head and corrected efficiency against corrected capacity. Draw smooth curves through these points. The head at shut-off can be taken as approximately the same as that for water.

Divide the viscous head (Hvis) by the head correction factor (CH) from the curve marked "1.0 x Qw" to get the approximate equivalent water head (Hw approximately). Using this new equivalent water headcapacity point, select a pump in the usual manner.

Enter the chart (Fig. 5) at the bottom with the desired viscous capacity, (Qvis) and proceed upward to the desired viscous head (Hvis) in feet of liquid. For multi-stage pumps, use head per stage. Proceed horizontally (either left or right) to the fluid viscosity, and then go upward to the correction curves. Divide the viscous capacity (Qvis) by the capacity correction factor (CQ) to get the approximate equivalent water capacity (Qw approximately).

Calculate the viscous brake horsepower (bhpvis) from the formula given above.

Plot these points and draw a smooth curve through them which should be similar to and approximately parallel to the brake horsepower (bhp) curve for water.

1167

TECH-D

EXAMPLE. Given the performance of a pump (Fig. 6) obtained by test on water, plot the performance of this pump when handling oil with a specific gravity of 0.90 and a viscosity of 1000 SSU at pumping temperature. On the performance curve (Fig. 6) locate the best efficiency point which determines (Qw). In this sample this is 750 gpm. Tabulate capacity, head and efficiency for (0.6 x 750), (0.8 x 750) and (1.2 x 750).

Using 750 gpm, 100 feet head and 1000 SSU, enter the chart and determine the correction factors. These are tabulated in Table 6 of Sample Calculations. Multiply each value of head, capacity and efficiency by its correction factor to get the corrected values. Using the corrected values and the specific gravity, calculate brake horsepower. These calculations are shown on Table 6. Calculated points are plotted in Fig. 6 and corrected performance is represented by dashed curves.

TECH-D-4 Viscosity Corrections for Capacities of 100 GPM or Less

Fig. 5A

TECH-D

1168

Fig. 6 Sample Performance Chart

TABLE 6

1169

TECH-D

TECH-D-5A Viscosity of Common Liquids

Glycol: Propylene Triethylene Diethylene Ethylene Hydrochloric Acid(31.5) Mercury Phenol (Carbonic Acid) Silicate of soda Freon Glycerine (100%) Liquid 1.37 to 1.49 @ 70 F 1.26 @ 68F 1.038 @ 68F 1.125@ 68 F 1.12 1.125 1.05 @ 68 F 13.6 .95 to 1.08 40 Baume 42 Baume 1.83 *Sp Gr at 60 F

Reprinted from PIPE FRICTION MANUAL, Third Edition. Copyright 1961 by Hydraulic Institute.

VISCOSITY SSU 2,950 813 Centistokes .27-.32 648 176 52 40 32 17.8 1.9 .118 .11 11.7 79 138 14.6

At F 70 68.6 100 70 70 70 70 68 70 100 65 100 100 68

240.6 185.7 149.7 88.4 65 365 637.6 75.7

Sulfric Acid (100%) FISH AND ANIMAL OILS: Bone Oil Lard Cod Oil

Mineral Oils: Automobile Crankcase Oils (Average Midcontinent Parrafin Base) SAE 10 SAE 30 SAE 20

Whale Oil

Sperm Oil

Neatsfoot Oil

Menhaddden Oil

Lard Oil

.925

.883

.917

.933

.912 to .925

.96

.928

.918

220 65 150 95 287 160 190 to 220 112 to 128 140 90 230 130 110 78 163 to 184 97 to 112 165 to 240 90 to 120 240 to 400 120 to 185 400 to 580 185 to 255 580 to 950 255 to 80 950 to 1,600 80 to 105 1,600 to 2,300 105 to 125 2,300 to 3,100 125 to 150 5,000 to 10,000 10,000 to 40,000 100,000 max 800 To 1,500 300 to 500 950 to 2,300 120 to 200 Over 2,300 Over 200 40 to 783 34.2 to 210 74 to 1,215 46 to 320 40 to 4,480 34 to 700 46 to 216 38 to 86 165 to 240 90 to 120

47.5 11.6 32.1 19.4 62.1 34.3 41 to 47.5 23.4 to 27.1 29.8 18.2 49.7 27.5 23.0 15.2 35 to 39.6 19.9 to 23.4 35.4 to 51.9 18.2 to 25.3 51.9 to 86.6 25.3 to 39.9 86.6 to 125.5 39.9 to 55.1 125.5 to 205.6 55.1 to 15.6 205.6 to 352 15.6 to 21.6 352 to 507 21.6 to 26.2 507 to 682 26.2 to 31.8 1,100 t o2,200 2,200 TO 8,800 22,000 max 173.2 to 324.7 64.5 to 108.2 205.6 to 507 25.1 to 42.9 Over 507 Over 42.9 4.28 to 169.5 2.45 to 4.53 14.1 to 263 6.16 to 69.3 4.28 to 1,063 2.4 to 151.5 6.16 to 46.7 3.64 to 17.2 35.4 to 51.9 18.2 to 25.3

130 212 100 130 100 130 100 130 100 130 100 130 100 130 100 130 100 130 100 130 100 130 100 130 210 100 210 100 210 100 210 0 0

SAE 40 SAE 50

**.880 to .935 **.880 to .935

**.880 to .935

**.880 to .935

**.880 to .935

SAE 10W SAE 20W Automobile Transmission Lubricants: SAE 80 SAE 90 SAE 250 SAE 140

SAE 70

SAE 60

**.880 to .935 **.880 to .935

**.880 to .935

**.880 to .935

**.880 to .935 **.880 to .935 **.880 to .935

Crude Oils: Texas, Oklahoma California

**.880 to .935 .81 to .916

Wyoming, Montana

* Unless otherwise noted.

Diesel Engine Lubricating Oils (Based on Average Midcontinent Parafin Base): Federal Specefication No. 9110

Pennsylvania

.8 to .85

.78 to .92

.86 to .88

**.880 to .935

60 100 60 100 60 100 60 100 100 130

0 100 130 130 210 130 210

TECH-D

** Depends on origin or percent and type of solvent.

1170

VISCOSITY Diesel Engine Lubricating Oils (Based on Average Midcontinent Parafin Base): Federal Specification No.9170 Liquid *Sp Gr at 60 F **.880 to .935 SSU 300 to 410 140 to 180 470 to 590 200 to 255 800 to 1,100 320 to 430 490 to 600 92 to 105 32.6 to 45.5 39 45.5 to 65 39 to 48 140 max 70 max 400 max 165 max Centistokes 64.5 to 88.8 29.8 to 38.8 101.8 to 127.8 43.2 to 55.1 173.2 to 238.1 69.3 to 93.1 106.1 to 129.9 18.54 to 21.6 2 to 6 1 to 3.97 6 to 11.75 3.97 to 6.78 29.8 max 13.1 max. 86.6 max 35.2 max

At F 100 130 100 130 100 130 130 210

Federal Specification No. 9500 Diesel Fuel Oils: No. 2 D No.4 D No.5 D No.3 D

Federal Specification No. 9370

Federal Specification No. 9250

**.880 to .935 **.82 to .95

**.880 to .935

**.880 to .935

**.82 to .95 **.82 to .95 **.82 to .95 **.82 to .95

**.82 to .95

Fuel Oils: No. 1 No.3 No. 2

**.82 to .95

No.5B No.6

No.5A

**.82 to .95 **.82 to .95

**.82 to .95

Machine Lubricating Oil (Average Pennsylvania Parafin Base): Federal Specification No.8 Federal Specification No. 20 Federal Specification No. 10

Insulating Oil: Transformer, switches and Circuit breakers Kerosene

Gasoline (Natural) Gas Oil

Gasoline

Fuel Oil Navy II

Fuel Oil Navy Specification

76.5 degrees API 28 degrees Api

.68 to .74

1.0 max

**.989 max

34 to 40 32 to 35 36 to 50 33 to 40 35 to 45 32.8 to 39 50 to 125 42 to 72 125 to 400 72 to 310 450 to 3,000 175 to 780 110 to 225 63 to 115 1,500 max 480 max 73 50 65 max 35 32.6 112 to 160 70 to 90 160 to 235 90 to 120 235 to 385 120 to 185 385 to 550 185 to 255 140 to 190 86 to 110 190 to 220 110 to 125 100 77

2.39 to 4.28 2.69 3.0 to 7.4 2.11 to 4.28 2.69 to .584 2.06 to 3.97 7.4 to 26.4 4.91 to 13.73 26.4 to 86.6 13.63 to 67.1 97.4 to 660 37.5 to 172 23 to 48.6 11.08 to 23.9 324.7 max 104 max .46 to .88 .40 to .71 .41 13.9 7.4 11.75 max 2.69 2 23.4 to 34.3 13.1 to 18.2 34.3 to 50.8 18.2 to 25.3 50.8 to 83.4 25.3 to 39.9 83.4 to 119 39.9 to 55.1 29.8 to 41 17.22 to 23 41 to 47.5 23 to 26.4 20.6 14.8

70 100 70 100 100 130 100 130 100 122 130 122 160 122 160 122 160 60 100 68 70 100 100 68 100 100 130 100 130 100 130 100 130

100 130 100 130 100 130 122 160

.78 to .82 **.880 to .935

Mineral Lard Cutting Oil: Federal Specefication Grade 1 Petrolatum Federal Specification Grade 2

Federal Specification No. 30

**.880 to .935

**.880 to .935

**.880 to .935

Turbine Lubricating Oil: Federal Specification (Penn Base) VEGETABLE OILS: Castor Oil China Wood Oil Cocoanut Oil Corn Oil

.825 .91 Average .96 @ 68 F .943 .925 .924 .88 to .925

Cotton Seed Oil

* Unless otherwise noted.

** Depends on origin or percent and type of solvent.

1,200 to 1,500 450 to 600 1,425 580 140 to 148 76 to 80 135 54 176 100

400 to 440 185 to 205

259.8 to 324.7 97.4 to 129.9 308.5 125.5 29.8 to 31.6 14.69 to 15.7 28.7 8.59 37.9 20.6

86.6 to 95.2 39.9 to 44.3

100 130 69 100 100 130 130 212 100 130

100 130

100 130 100 130 130 160

1171

TECH-D

VISCOSITY VEGETABLE OILS: Linseed Oil, Raw Palm oil Olive oil Liquid *Sp Gr at 60 F .925 to .939 SSU 143 93 200 115 221 125 195 112 250 145 1,500 600 500 to 20,000 1,000 to 50,000 184 110 165 96 33 32.6 Centistokes 30.5 18.94 43.2 24.1 47.8 26.4 42 23.4 54.1 31 324.7 129.9 108.2 to 4,400 216.4 to 11,000 39.6 23 35.4 19.64 2.11 2.0

At F 100 130 100 130 100 130 100 130 100 130 100 130 200 190 100 130 100 130 60 100 100 130 100 150 100 100 130 100 130 100 130

Rosin (Wood) Soja Bean Oil Sesame Oil

Rosin Oil

Rape Seed Qil

Peanut Oil

1.09 Avg .927 to.98 .923

.980

.919

.920

.924

.912 to .918

SUGARS, SYRUPS, MOLASSES, ETC. Corn Syrups Honey (Raw) Molasses A (First) MolassesB (Second) Molasses C (Blackstrap or final) Sucrose Solutions(Sugar Syrups) 60 Brix 62 Brix 64 Brix 66 Brix 68 Brix 70 Brix 72 Brix 74 Brix TARS: Tar Coke Oven Road Tar: Grade RT-2 Grade RT-4 Grade RT-6 Grade RT-10 Grade RT-8 Tar Gas House 76 Brix Glucose

Turpentine

.86 to .87

1.4 TO 1.47

1.35 to 1.44 140.6 to 146 1.46 to 1.49 1.29 1.43 to 1.48

5,000 to 500,000 1,500 to 60,000 35,000 to 100,000 4,000 to 11,000 340 1,300 to 23,00 700 to 8,000 6,500 to 60,000 3,000 to 15,000 17,00 to 250,000 6,000 to 75,00 230 92 310 111 440 148 650 195 1,000 275 1,650 400 2,700 640 5,500 1,100 10,000 2,000

1,1000 324.7 7,700 880

to 110.000 to 13,200 to 22,000 to 2420 73.6 281.1 to 5,070 151.5 to 1,760 1,410 to 13,200 660 to 3,300 2,630 to 5,500 1,320 to 16,500 49.7 18.7 67.1 23.2 95.2 31.6 140.7 42.0 216.4 59.5 364 86.6 595 138.6 1,210 238 2,200 440

1.30 1.31

1.326 1.338 1.35 1.36 1.39

1.376

1.12+

1.16 to 1.30 1.07+ 1.08+ 109+ 1.13+

3,000 to 8,000 650 to 1,400 15,000 to 300,000 2,000 to 20,000 200 to 300 55 to 60 400 to 700 65 to 75 1,000 to 2,000 85 to 125 3,000 to 8,000 150 to 225 20,000 to 60,000 250 to 400 114,000 to 456,000 500 to 800 2,500 500 150 130 600 440

Grade RT-12 Pine Tar

1.15+ 1.06 1.18 1.20

1.14+

MISCELLANEOUS Corn Starch Solutions: 22 Baume 24 Baume

* Unless otherwise noted.

43.2 to 64.9 8.77 to 10.22 86.6 to 154 11.63 to 14.28 216.4 to 440 16.83 to 26.2 660 to 1,760 31.8 to 48.3 4,400 to 13,200 53.7 to 86.6 25,000 to 75,000 108.2 to 173.2 559 108.2 32.1 27.5 129.8 95.2

600 to 1,760 140.7 to 308 3,300 to 66,000 440 to 4,400

71 100 70 100

70 100 70 100 70 100 70 100 70 100 70 100 70 100 70 100 70 100

122 212 122 212 122 212 122 212 122 212 122 212 100 132

70 100 70 100

TECH-D

1172

VISCOSITY MISCELLANEOUS Corn Starch Solutions: 25 Baume Liquid *Sp Gr at 60 F 1.2 SSU 1400 800 2,500 to 10,000 1,100 to 3,000 56 1425 650 Centistokes 303 17.2 550 to 2,200 238.1 to 660 9.07 1.13 313 143 1.13 .55

At F 70 100 100 130 212 68 68 100 60 130

Water- Fresh

Tallow Milk Varnish Spar

Ink- Printers

1.0

.918 Avg. 1.02 to 1.05 .9

1.00 to 1.38

TECH-D-5B Physical Properties of Common Liquids

* Unless otherwise noted.

Liquid Acetic Acid Glacial 8.8% (1N) .88% (.1N) .09 (.01N) Acetone

Sp. Gr. 60 F (16C) 1.05

Melting Point F (C) 63 (17)

Boiling pH Point At 77 F F (C) (25C) 244 (118) 133 (56) 2.4 2.9 3.4 3.2 11.6 11.1 10.6

40F

80F

SSU

VISCOSITY 120F 160F 4C 1.6

Centipoise 27C 49C 1.2 .8

71C .6

1.01 .79

Alum, 0.6% (0.1N) Ammonia 100% 26% 1.7% (1N) .17% (0.1N) .02% (.01N) Asphalt Unblended RS1 RC2 RC5 Emulsion Benzene

.77

- 137 (-94) -108 (-78)

.4 .14 1.8

.3 .1

.3 .08

.2 .06

.91

-27 (-33)

1.2

1.1-1.5 1.0 1.0 1.0 1.0 .84

Benzoic Acid 0.1% (.01N) Black liquor, 50% 70%

42 (6)

176 (80)

500,000 1 ,000-7,000 3.1

155-1,000

160 2,400-5,000 45,000

(12,000 at 250F) 85 8,000 .8

86 .6

34 .5

17 .3

1.3

Borax

Calcium Hydroxide Sat. (Slaked Lime) Carbolic Acid (Phenol)

0.2% (0.1N) Butane Calcium Carbonate Sat. Calcium Chloride 25%

1% (0.1N) Boric Acid

1.7 (75)

1.5

5,000

167 338 (171)

(80-150 at 250F) (6,300 at 250F)

(15-37 at 121C) 1,400 at 121C)

9.2 5.2 9.4 .18

.59

1.23

-21 (-29)

4.5 12.4 360 (182) 14.5

2.1

.9

.5

1.07

Reprinted with permission of the Durametallic Corporation.

109 (43)

60

7.3

3.9

2.1

1173

TECH-D

Liquid Carbonic Acid Sat. Carbon Tetrachloride Citric Acid .6% (1n) Corn Oil Corn Starch, 22 Baume 25 Baume Corn Syrup

Sp. Gr. 60 F (16C)

Melting Point F (C)

Boiling pH Point At 77 F F (C) 25C) 3.8

40F

80F

SSU

VISCOSITY 120F 160F 4C

Centipoise 27C 49C

71C

1.58 .92

-95 (-71)

170 (77)

1.3 135

.9

.7

.6

2.2 150 1,400

Cotton Seed Oil Crude Oil Pennsylvania Wyoming 48 API 32.6 API Dowtherm A Ethane Dowtherm C

1.18 1.21 1.4 .8 .9 .79 .86 .99 .9

200 1,100 54 (12) 70 (21) - 173 (- 144) 9 (- 13) 47 (8) 500 (260) 600 (316) 173 (78) 387 (198) 2.3 185 86

130 800 5,000500,000 176 86 320 2.8 20.0

Ethyl Alcohol

.37

1.1 .79 .81 1.1

Ethyl Alcohol 95% Ethylene Glycol

1.6 53 39 2.0 44 2.4 40 43 84 100 200 15,000 30 36 36 52 4,50020,000 53 80 2,000 31 33 41 680- 1,900 40 50 400 30 32 37 180500 35 40 160 3.3 4.6 15

(.05 at 16 C.) 1.0 1.3 19

.7 .8 9 1.4 1.6 4 155

.5 .6 4 .8 0.9 1.2 3 40

Ethyl Acetate Formic Acid, 1.22 100% .5% (.1N) Fuel Oil No. 1 (Kerosene) No. 2 No. 3 No. 6 (Bunker C) Diesel 2D 3D 5D Gasoline Glucose

.9 122 1.0 .81 .86 .89 .96

213 (100) -

.49 1.5 2.1 2.6 7 1,00

Glycerine (Glycerol) 50% Hydrochloric Acid, 38% 3.6% (1N) .36% (0.1N) .04% (.01N) Jet Fuel Lactic Acid Methyl Alcohol 80% Milk, 3.5% Molasses A Molasses C 31.5%

.82-.95 .82-.95 .82-.95 .6-.7 1.4 1.26 1.13 64 (18) 554 (290)

25,000

3,100

35,000100,000 700

.7 6,260 11 2.5

.6 490 5.4 1.8

.4 130 2.8 1.4

.3 56 1.5 1.1

230

1.20 1.15

- 13 (-25) -115 (-46)

.7-.8 .80 .82 1.03 1.40 1.49

63 (17) - 144 (-98)

252 (122) 149 (65)

0.1 1.1 2.0 2.4 6.3-6.6

35 .8 1.0 .5 .7 1.1 .4 .5

300,000

10,000

2,60060,000 25,000250,000

.4

TECH-D

1174

Liquid Nitric Acid, 95% Oil, 5W 10W 20W 30W 50W 70W Oleic Acid 60%

Sp. Gr. 60 F (16C) 1.50

Melting Point F (C) -44 (-44) -9 (-23)

Boiling pH Point At 77 F F (C) 25C) 187 (86)

40F

80F

SSU

VISCOSITY 120F 160F 4C 1.4

Centipoise 27C 49C 1.0 .8

71C .6

1.37 .9 .9 .9 .9 .9 0.89

Olive Oil Palmetic Acid Peanut Oil Propane Propylene Gylcol Potassium Hydroxide 5.7% (1N) 0.57% (0.1N) 0.06% (0.01N) Rosin Sodium Bicarbonate 0.4% (0.1N) Sodium Chloride, 25% Sodium Hydroxide, 50% 30% 4% (1N) 0.4% (0.1N) .04% (.01N) Stearic Acid Sucrose, 60% 40 % Parafin

.9 0.85 .9 .51 1.0 .9

13 (-11) 146 (63) 100 (38)

547 (286)

550 1,500 2,900 5,000 23,000 120,000 1,500

160 265 500 870 3,600 10,000 320

74 120 170 260 720 1,800 150

51 64 80 110 225 500 80

110 170 580 1,200 -

3.4

30 50 98 200 400 4,000 26

2.2

12 22 33 60 100 -

1.5

1.0 7 11 14 25 45 -

520 (271) 660 (349)

1,200

300

241

150

80

.12

1.09

14.0 13.0 12.0 8.4 950 240 58 84

500-20,000

1.53 1.33 .85

1.19

Sugar Syrup 60 Brix 70 Brix 76 Brix Sulfur Molten Sulfric Acid 110% (Fuming, Oleum) 100% 60% 98%

1.18

1.29

1.29 1.35 1.39 2.06 1.83 1.50 1.84

157 (69) 10 (- 12) 25 (-4)

721 (383) 218 (103) 214 (101)

14.0 13.0 12.0

46

250

3.3

2.1 77 10

26 4.5

1.3

10 2.5

.9

500

150

68

156

120

41 5

2.5

14

1.6

239 (115) 50 (10) 37 (3) -83 (-64) 8 (-13) -139 (-95) -99 (-72) 140 (-10) 32 (0) 1.03 92

832 (445) 342 (33) (172)

230 1,650 10,000 280 118 100 75 68

92 400 2,000 55 45 37

(11 at 123C) 82 46

(9 at 159C) 41 23

(22 at (16,000 at 160C) 184C) 22 12 12 6

4.9% (1N) .49% (.1N) .05 (.01N) Toluene Turpentine Vinegar Water Wines

20%

1.14 .86

554 (290) 282 (139) 218 (103) 231 (111) 189 (87) 320 (160)

8.9

0.3 1.2 2.1

2.5 .8

5.8

1.4 .6

3.9

0.8 .4

2.7

0.6 .4

Trichloroethylene

1.62 .86

1.0

212 (100)

2.4-3.4 6.5-8.0

34 32

33

32

32

1.9 1.6

.7

1.4 .9

.6

.5

.9 .6

.4

.7 .4

2.8-3.8

1175

TECH-D

TECH-D-6 Friction Loss for Viscous Liquids. Loss in Feet of Liquid per 100 Feet of New Schedule 40 Steel Pipe
GPM 3 5 10 15 20 30 40 60 80 100 125 150 175 200 250 300 400 600 800 1000 Nom. Pipe Size 1 /4 1 11/4 1 11/4 11/2 1 11/4 11/2 1 11/2 2 11/2 2 21/2 11/2 2 21/2 2 21/2 3 21/2 3 4 21/2 3 4 3 4 6 3 4 6 3 4 6 3 4 6 4 6 8 6 8 10 6 8 10 6 8 10 6 8 10 8 10 12
3 1 /2 3 /4

Kinematic Viscosity Seconds Saybolt Universal 10.0 2.50 0.77 6.32 1.93 0.51 6.86 1.77 0.83 14.6 3.72 1.73 25.1 2.94 0.87 6.26 1.82 0.75 10.8 3.10 1.28 6.59 2.72 0.92 4.66 1.57 0.41 7.11 2.39 0.62 3.62 0.94 0.12 5.14 1.32 0.18 6.9 1.76 0.23 8.90 2.27 0.30 3.46 0.45 0.12 1.09 0.28 0.09 1.09 0.28 0.09 2.34 0.60 0.19 4.03 1.02 0.33 1.56 0.50 0.21 Water 25.7 8.5 3.2 14.1 5.3 1.8 11.2 3.6 1.9 26 6.4 2.8 46 5.3 1.5 11.6 3.2 1.4 19.6 5.8 2.5 11.6 5.1 1.8 8.3 3.0 0.83 12.2 4.4 1.2 6.5 1.8 0.25 9.2 2.4 0.34 11.7 3.2 0.44 15.0 4.2 0.58 6.0 0.83 0.21 8.5 1.2 0.30 1.9 0.53 0.18 4.2 1.1 0.37 6.5 1.8 0.60 2.5 0.88 0.39 100 54.4 17.5 6.6 29.3 11.0 3.7 22.4 7.5 4.2 34 11.3 6.2 46 8.1 3.0 12.2 4.4 2.2 20.8 5.8 3.0 13.4 5.5 1.8 9.7 3.2 0.83 14.1 5.1 1.3 7.8 2.1 0.28 10.4 2.9 0.39 13.8 4.0 0.52 17.8 5.1 0.69 7.4 0.99 0.28 9.9 1.4 0.39 2.3 0.62 0.21 5.1 1.3 0.42 8.1 2.2 0.69 3.2 1.0 0.46 200 83 108 135 162 26.7 35.5 44 53 10.2 13.4 16.6 20.0 44 59 74 88 16.8 22.4 28 33 5.5 7.6 9.5 11.1 33.5 45 56 66 11.2 14.9 19.1 22.4 6.0 8.1 10.2 12.3 50 67 85 104 16.9 22.4 29 34 9.2 12.4 15.3 18.4 67 90 111 133 12.2 16.2 20.3 25 4.4 6.0 7.4 9.0 18.2 24.3 30 37 6.7 9.0 11.1 13.2 3.2 4.4 5.5 6.5 24 32 40 50 9.0 11.8 14.8 17.7 4.4 5.8 7.4 8.8 13.4 17.8 22.2 27 6.5 8.8 10.9 13.1 2.8 3.7 4.6 5.6 9.7 11.8 14.6 17.6 3.7 4.8 6.2 7.3 1.2 1.7 2.1 2.5 14.8 14.8 18.5 22 5.1 6.2 7.6 9.1 1.5 2.1 2.5 3.1 8.1 8.1 9.7 11.5 2.1 2.6 3.2 3.9 0.39 0.52 0.63 0.78 11.5 11.5 11.5 13.7 2.9 3.1 3.9 4.6 0.46 0.62 0.77 0.9 15.8 15.8 15.8 15.9 4.0 4.0 4.6 5.4 0.54 0.7 0.9 1.1 20.3 20.3 20.3 20.3 5.1 5.1 5.1 6.2 0.69 0.81 1.0 1.2 8.0 8.0 8.0 8.0 1.0 1.0 1.2 1.5 0.28 0.35 0.42 0.51 11.6 11.6 11.6 11.6 1.5 1.5 1.5 1.8 0.39 0.42 0.51 0.61 2.5 2.8 2.8 2.8 0.67 0.67 0.67 0.81 0.23 0.23 0.28 0.32 5.3 5.5 6.0 6.2 1.4 1.5 1.5 1.5 0.46 0.51 0.51 0.51 8.5 9.2 9.7 11.1 2.3 2.5 2.8 2.8 0.78 0.88 0.92 0.92 3.5 3.7 4.2 4.4 1.2 1.3 1.4 1.4 0.51 0.55 0.58 0.58 300 400 500 600 218 71 26.6 117 44 14.8 89 30 16.5 137 45 25 180 33 11.9 50 17.8 8.8 65 24 11.8 36 17.8 7.3 24 9.7 3.3 29 12.1 4.1 15.3 5.2 1.0 18.4 6.2 1.2 21.4 7.4 1.4 25 8.3 1.6 10.2 2.1 0.67 12.4 2.5 0.82 3.2 1.1 0.43 6.2 1.7 0.65 11.1 2.8 0.92 4.4 1.4 0.58 800 273 88 34 147 56 18.5 112 37 20.3 172 57 30 220 40 14.8 61 22.2 10.9 81 30 14.6 45 22.0 9.2 29 12.2 4.2 36 15.2 5.1 19.4 6.4 1.3 23 7.8 1.5 27 9.2 1.8 31 10.4 2.0 12.9 2.5 0.83 15.5 3.0 1.0 3.9 1.3 0.53 6.2 2.0 0.81 11.1 2.8 1.1 4.4 1.4 0.67 1000 411 131 50 219 83 28 165 55 31 84 46 61 22.4 91 33 16.6 121 44 22.2 67 34 13.8 44 18.3 6.2 55 23 7.8 29 9.8 1.9 35 11.5 2.3 40 13.7 2.6 46 15.5 3.0 19.4 3.7 1.2 23 4.6 1.5 6.0 2.0 0.81 9.0 3.0 1.2 12.0 3.9 1.6 5.1 2.0 1.0 1500 545 176 67 293 111 37 223 74 41 112 61 81 30 122 45 22.0 162 59 29 89 44 18.5 58 24 8.3 73 31 10.4 39 12.7 2.6 46 15.4 3.0 53 18.2 3.5 61 20.6 3.9 26 5.1 1.7 31 6.0 2.0 8.1 2.8 1.1 12.0 3.9 1.6 16.0 5.3 2.1 6.7 2.8 1.3 2000 820 1350 265 440 880 100 167 440 740 1470 167 56 94 187 112 190 62 102 207 167 92 152 122 203 45 74 147 182 67 178 222 33 55 110 243 400 810 89 148 44 73 145 134 220 66 109 220 27 46 92 87 145 37 61 122 12.5 20.6 41 109 183 46 77 150 15.5 26 51 58 97 193 19.3 32 65 3.9 6.4 13.0 69 115 230 23 39 78 4.6 7.6 15.2 80 133 28 46 92 5.3 8.8 17.8 91 152 31 51 103 6.2 9.9 20.1 39 64 130 7.6 12.5 2.5 4.2 8.3 46 77 155 9.1 15.0 30 3.0 5.1 9.9 12.1 20.1 4.1 6.7 13.5 1.6 2.8 5.3 18.5 6.2 9.9 20 2.4 4.2 8.1 8.2 13.4 3.2 5.3 10.9 10.2 16.6 4.0 6.7 13.4 2.0 3.5 6.7 3000 5000 10,000

Extracted from PIPE FRICTION MANUAL. Third Edition. Copyright 1961 by Hydraulic Institute.

TECH-D

1176

TECH-D-7 Pumping Liquids with Entrained Gas

Pump applications in many industrial processes involve handling liquid and gas mixtures. The entrained gas may be an essential part of an industrial process, or it may be unwanted. The Pulp and Paper industry, for example, injects from between 4% and 10% air into a dilute pulp slurry as part of the ink removal process in a flote cell used in paper recycling. Many chemical and petrochemical processes also involve pumping a two phase flow. Unwanted entrained gas can result from excess agitation or vortexing due to inadequate submergence on the suction of a pump. The proper selection of a centrifugal pump for liquid and gas (two phase) mixtures is highly dependent on the amount of gas and the characteristics of the liquid. The presence of entrained gases will reduce the output of centrifugal pumps and can potentially cause loss of prime. Conventional pump designs can be used for low percentages by volume (up to 4%), while special modified impellers can be used effectively for up to 10% gas by volume. Performance corrections are required in all cases with gas content above approximately 2%. Gas concentrations above 10% can also be handled, but only with special design pumps (pumps with inducers, vortex pumps, or pumps with gas extraction). Virtually any type of centrifugal pump can handle some amount of entrained gas. The problem to be addressed is the tendency for the

gas to accumulate in the pump suction inhibiting flow and head generation. If gas continues to accumulate, the pump may lose prime. Fig. 1 shows how the performance of a standard end suction pump is affected by various amounts of air. With a minor performance correction, this type of pump is reasonably efficient in handling up to approximately 4% entrained gas.

As the percentage of gas exceeds 4% by volume, the performance of a conventional pump begins to degrade drastically (Fig. 1) until the pump becomes unstable, eventually losing prime. It has been found beneficial to increase the impeller running clearance (0.090 to 0.180 in.) allowing for greater leakage. This is effective in preventing loss of prime with gas concentrations up to 10%. Fig. 2 shows a standard end suction open impeller pump with clearances opened for gas handling. Numerous tests have been conducted in an effort to quantify the performance corrections for various gas concentrations for both standard pumps and pumps with open clearances. The performance corrections are affected by many variables, including pump specific speed, operating speed, impeller design and number of vanes, operating point on the curve, and suction pressure. Performance correction charts are not presented here due to the numerous variables, but Goulds Applications Engineers can make recommendations and selections for most specific applications.

Standard Clearance (Typically .015") Increased Running Clearance (Typically .090" - .180")

Fig. 1 Head and Power vs Capacity Zero to Ten Percent Air by Volume for Normal Running Clearance

Fig. 2 Open Impeller End Suction Pump with Normal Running Clearance and Increased Running Clearance.

1177

TECH-D

TECH-D-8A Solids and Slurries - Definition of Terms

APPARENT VISCOSITY The viscosity of a non-Newtonian slurry at a particular rate of shear, expressed in terms applicable to Newtonian fluids. CRITICAL CARRYING VELOCITY The mean velocity of the specific slurry in a particular conduit, above which the solids phase remains in suspension, and below which solid-liquid separation occurs. EFFECTIVE PARTICLE DIAMETER The single or average particle size used to represent the behavior of a mixture of various sizes of particles in a slurry. This designation is used to calculate system requirements and pump performance. FRICTION CHARACTERISTIC A term used to describe the resistance to flow which is exhibited by solid-liquid mixtures at various rates of flow. HETEROGENEOUS MIXTURE A mixture of solids and a liquid in which the solids are net uniformly distributed. HOMOGENEOUS FLOW (FULLY SUSPENDED SOLIDS) A type of slurry flow in which the solids are thoroughly mixed in the flowing stream and a negligible amount of the solids are sliding along the conduit wall. HOMOGENEOUS MIXTURE A mixture of solids and a liquid in which the solids are uniformly distributed. NON-HOMOGENEOUS FLOW (PARTIALLY SUSPENDED SOLIDS) A type of slurry flow in which the solids are stratified, with a portion of the solids sliding along the conduit wall. Sometimes called "heterogeneous flow or flow with partially suspended solids. NON-SETTLING SLURRY A slurry in which the solids will not settle to the bottom of the containing vessel or conduit, but will remain in suspension, without agitation, for long periods of time. PERCENT SOLIDS BY VOLUME The actual volume of the solid material in a given volume of slurry, divided by the given volume of slurry, multiplied by 100. NOTE: PERCENT SOLIDS BY WEIGHT The weight of dry solids in a given volume of slurry, divided by the total weight of that volume of slurry, multiplied by 100. SALTATION A condition which exists in a moving stream of slurry when solids settle in the bottom of the stream in random agglomerations which build up and wash away with irregular frequency. SETTLING SLURRY A slurry in which the solids will move to the bottom of the containing vessel or conduit at a discernible rate, but which will remain in suspension if the slurry is agitated constantly. SETTLING VELOCITY The rate at which the solids in a slurry will move to the bottom of a container of liquid that is not in motion. (Not to be confused with the velocity of a slurry that is less than the critical carrying velocity as defined above.) SQUARE ROOT LAW A rule used to calculate the approximate increase in critical carrying velocity for a given slurry when pipe size is increased. It states: 1/ 2 VL = Vs = DL Ds Where: VL DL Vs Ds = Critical carrying velocity in larger pipe = Diameter of larger pipe = Critical carrying velocity in smaller pipe = Diameter of smaller pipe

()

This rule should not be used when pipe size is decreased.

VISCOSITY TYPES

(For definitions of the various types of viscosities applicable to slurries, see Rheological Definitions.) YIELD VALUE (STRESS) The stress at which many non-Newtonian slurries will start to deform and below which there will be no relative motion between adjacent particles in the slurry.

TECH-D-8B Solids and Slurries - Slurry Pump Applications

Determining the when to use a slurry style centrifugal pump can be a challenging decision. Often the cost of a slurry pump is many times that of a standard water pump and this can make the decision to use a slurry pump very difficult. One problem in selecting a pump type is determining whether or not the fluid to be pumped is actually a slurry. We can define a slurry as any fluid which contains more solids than that of potable water. Now, this does not mean that a slurry pump must be used for every application with a trace amount of solids, but at least a slurry pump should be considered. Slurries to be handled by centrifugal pumps may be placed into 4 categories, numbered 1, 2, 3 and 4. Class 1 slurries are least severe in terms of wear and effect on pump performance, while class 4 slurries produce the most rapid, severe pump wear and require the greatest correction to clear water performance. The class of the slurry in question is determined using the following method: 1. Determine the following: a. Slurry d50 (50% passing solids diameter) b. Slurry Sm (mixture specific gravity) 2. c. Miller abrasivity index of solids (Miller numbers for common materials are listed in the table found in Fig. F) Adjust the slurry specific gravity for Miller number effect:

Where M = Miller abrasivity index of solids in question (based on ASTM G75-95)

TECH-D

1178

3. Use Fig. 1 below to determine which class the slurry in question falls into.

Although selecting the proper slurry pump for a particular application can be quite complex, the selection task can be broken down into a simplified three-step process:

1. Determine which group of possible pump selections best matches your specific application. 2. Plot the system curve depicting the required pump head at various capacities. 3. Correct pump performance for slurry effects (if necessary).

4. Match the correct pump performance curve with the system curve.

Slurry pumps can be broken down into two main categories: the rubber-lined pump and the hard metal pump. Because of the elastomer lining, the rubber-lined pumps have a somewhat limited application range. Below is a general guideline which helps distinguish when to apply the rubber-lined pumps.
Solids < 1/4 inch (6mm) for SRL, SRL-C, Solids < 1/2 (13mm) SRL-XT Low Head service < 150 feet (46m) Rounded particles

Rubber Lined

Solids > 1/4 inch (13mm)

Hard Metal Pump

Slurry pumps sold by ITT IP/Goulds Pumps are categorized as follows: AF HS HSUL VHS JC JCU VJC CV 3196 Class 1 AF HS HSUL VHS JC JCU VJC CWX SRL-S SRL Class 1 and 2 SRL-C SRL-CM RX Class 3 SRL-XT SRL-XTM RXA CW 5500 5500S 5500LS CKX Class 4

Fig. 1 Slurry Classification Graph (Courtesy of Hydraulic Institute, www.pumps.org)

Temperature < 300 F (150C)

Temperature < 250 F (120C) Heads above 150 feet (46m) Sharp/Jagged particles pH range from 4 to 12 Hydrocarbon based slurry

Complete pH range

It should be noted, however, that a hard metal pump can also be used for some services that are outlined for the rubber-lined pump. After a decision has been made whether to use a hard metal pump or a rubber-lined pump, it is then time to select a particular pump model. A pump model should be selected by reviewing the application and determining which model pump will work best in the service. NOTES: The Model HS pump is a unique pump in that it is a recessed impeller or vortex" pump. This style pump is well suited to handle light pulpy or fibrous slurries. The recessed impeller used in the HS family of pumps will pass large stringy fibers and should be considered when pump plugging is a concern. The Model AF is a specialized pump with an axial flow design. This design of pump is built specifically for high flow, low head applications. In general, slurry pumps have been designed to handle fluids with abrasive solids and will give extended lives over standard water or process pumps. Although many features have been designed into the slurry pump, there are still two factors which directly relate to the pump's life that can be determined. The first choice to make is determining the metallurgy of the pump. In most cases, a hard metal slurry pump will be constructed of some hardened metal with a Brinell hardness of at least 500. Goulds standard slurry pump material is a 28% chrome iron with a minimum hardness of 600 Brinell. This material is used for most abrasive services and can also be used in some corrosive fluids as well. If a more corrosive resistant material is required, then the pump may be constructed out of a duplex Stainless Steel such as CD4MCu. Please check with your nearest Goulds sales office if you are unsure what material will be best suited for a particular application. PUMP RUNNING SPEED

While selecting a pump from a higher rating for a lower rated duty is acceptable (e.g. using a class 4 rated 5500 in a class 1 rated duty to fill a gap in JC hydraulics), it is not recommended to use a lighter duty pump in a heavy service (e.g. using a class 1 rated JC in a class 4 service). Other considerations in selecting a slurry pump are: Particle shape/angularity (angular or rounded?) Particle velocity and direction Maximum solids size Presence of tramp solids (e.g. unintended metal or wood scraps) Slurry pH and chloride content Petroleum or hydrocarbon content Froth/entrained air content Derating due to slurry effects on pump head and efficiency SLURRY PUMP DESIGN Thick Wear Sections Larger Impellers Specialty Materials Semi Volute or Concentric Casing Design Feature Longer component life Slower pump speeds longer Longer component life Improved pump life Improved bearing lives Benefit Compromise Heavier, more expensive parts Heavier, more expensive parts component life Expensive parts Loss in efficiency

Extra Rigid Power Ends

More expensive shafts and bearings

The other factor that can be controlled by the sales or end user engineer is the pump running speed. The running speed of a slurry pump is one of the most important factors which determines the life of the pump. Through testing, it has been proven that a slurry pump's wear rate is proportional to the speed of the pump raised to the 21/2 power.

1179

TECH-D

EXAMPLE:

With the above ratio in mind, it can be shown that by cutting a slurry pump speed in half, you get approximately 6 times the wear life. For this reason, most slurry pumps are V-belt driven with a full diameter impeller. This allows the pump to run at the slowest possible running speed and, therefore, providing the maximum pump life. WHY USE A V-BELT DRIVE? In most ANSI pump applications it is a reasonable practice to control condition point by trimming the impeller and direct connecting the motor. However, this is not always sound practice in slurry applications. The abrasive solids present, wear life is enhanced by applying the pump at the slowest speed possible. Another situation where V-belts are beneficial is in the application of axial flow pumps. Axial flow pumps cannot be trimmed to reduce the

then the life factor for Pump (B) as compared to Pump (A) is (1000/800)2.5 or Pump (B) will last 1.75 times as long as Pump (A).

If Pump (A) is running at 1000 RPM and Pump (B) is running at 800 RPM,

condition point because they depend on close clearances between the vane tips and the casing for their function. The generally low RPM range for axial flow application also makes it beneficial to use a speed reduction from the point of view of motor cost. The types of V-belt drives available for use in pump applications are termed fixed speed, or fixed pitch, and variable speed. The fixed pitch drive consists of two sheaves; each machined to a specific diameter, and a number of belts between them to transmit the torque. The speed ratio is roughly equal to the diameter ratio of the sheaves. The variable speed drive is similar to the fixed speed except that the motor sheave can be adjusted to a range of effective or pitch diameters to achieve a band of speed ratios. This pitch adjustment is made by changing the width of the Vgrooves on the sheave. Variable speed drives are useful in applications where an exact flow rate is required or when the true condition point is not well defined at the time that the pump is picked. V-belt drives can be applied up to about 500 horsepower, but pump applications are usually at or below 350 HP.

TECH-D-8C Solids and Slurries - Useful Formulas

where, a. The formula for specific gravity of a solids-liquids mixture or slurry, Sm is: Ss x S1 Sm = Ss + Cw (S1 Ss ) Sm = S1 = Ss = Cw = Cv = specific gravity of mixture or slurry specific gravity of liquid phase specific gravity of solids phase concentration of solids by weight concentration of solids by volume

See nomograph for the relationship of concentration to specific gravity of dry solids in water shown in Fig. B. c. Slurry flow requirements can be determined from the expression: Qm = 4 x dry solids (tons per hour) Cw = Sm Qm = slurry flow (U.S. gallons per minute) 1 ton = 2000 lbs. EXAMPLE: 2,400 tons of dry solids is processed in 24 hours in water with a specific gravity of 1.0 and the concentration of solids by weight is 30% with the solids having a specific gravity of 2.7 then: 2.7 x 1.0 Sm = = .123 2.7 + .3 (1-2.7) Qm = 4 x 100 = 1,084 U.S. GPM .3 x 1.23 where,

EXAMPLE: if the liquid has a specific gravity of 1.2 and the concentration of solids by weight is 35% with the solids having a specific gravity of 2.2, then: 2.2 x 1.2 Sm = = 1.43 2.2 + .35 (1.2 2.2) b. Basic relationships among concentration and specific gravities of solid liquid mixtures are shown below: In Terms of Cv Ss, Sm, S1 Sm-S1 Ss-S1 Cv Cw Sm Ss Cw

Cw

(Sm S1)

S x s (Ss S1) Sm

Cv Ss Sm

Where pumps are to be applied to mixtures which are both corrosive and abrasive, the predominant factor causing wear should be identified and the materials of construction selected accordingly. This often results in a compromise and in many cases can only be decided as a result of test or operational experience. For any slurry pump application, a complete description of the mixture components is required in order to select the correct type of pump and materials of construction. weight of dry solids CW = weight of dry solids + weight of liquid phase volume of dry solids volume of dry solids + volume of liquid phase

d. Abrasive wear: Wear on metal pumps increases rapidly when the particle hardness exceeds that of the metal surfaces being abraded. If an elastomer lined pump cannot be selected, always select metals with a higher relative hardness to that of the particle hardness. There is little to be gained by increasing the hardness of the metal unless it can be made to exceed that of the particles. The effective abrasion resistance of any metal will depend on its position on the Mohs or Knoop hardness scale or Miller abrasivity index. The relationships of various common ore minerals and metals is shown in Fig. A. Wear increases rapidly when the particle size increases. The life of the pump parts can be extended by choosing the correct materials of construction. Sharp angular particles cause about twice the wear of rounded particles. Castable ceramic materials have excellent resistance to cutting erosion but impeller tip velocities are usually restricted to 100 ft./sec.

Cv =

Hard irons are used to resist erosion and, to a lesser extent, impact wear.

TECH-D

1180

Solids and Slurries

Several elastomers are available for different applications. Hypalon is acceptable in the range of 1-14 pH. There is a single stage head limitation of about 150 due to tip speed limitations of elastomer

Elastomer lined pumps offer the best wear life for slurries with solids under 1/4" for the SRL/SRL-C and under 1/2" for the SRL-XT.

impellers, and of about 190 with metal impellers and elastomer liners due to liner degradation issues. See the Classification of Pumps according to Solids Size chart (Fig. C) and Elastomer Quick Selection Guide (Section TECH-B-2) for more information.

Approximate Comparison of Hardness Values of Common Ores and Minerals

Fig. A

1181

TECH-D

Solids and Slurries

Nomograph of the Relationship of Concentration to Specific Gravity in Aqueous Slurries

Cv % Solids by Volume

Ss Solids Specific Gravity

Cw % Solids by Weight Fig. B

Sm Slurry Specific Gravity

TECH-D

1182

Solids and Slurries

Tyler Standard Sieve Series Aperture Inch mm 160 4060 80 2030 40 1016 20 508 10 254 3 76.2 2 50.8 1.5 38.1 1.050 26.67 .883 22.43 .742 18.85 .624 15.85 .524 13.33 .441 11.20 .371 9.423 .321 7.925 .263 6.680 .221 5.613 .185 4.699 .156 3.962 .131 3.327 .110 2.794 .093 2.362 .078 1.981 .065 1.651 .055 1.397 0.46 1.168 0.39 .991 0.328 .833 0.276 .701 .0232 .589 .0195 .495 .0164 0.417 .0138 .351 .116 .295 .0097 .248 .0082 .204 .0069 .175 .0058 .147 .0049 .124 .0041 .104 .0035 .089 .0029 .074 .0024 .061 .0021 .053 .0017 .043 .0015 .038 .025 .020 .10 .005 .001 .0005 .0024 Mesh

Classification of Pumps According to Solid Size

Grade Very large boulders Large boulders Medium boulders Small boulders Large cobbles Small cobbles Very coarse gravel Coarse Gravel Austenetic Manganese Steel

2.5 3 3.5 4 5 6 7 8 9 10 12 14 16 20 24 28 32 35 42 48 60 65 80 100 115 150 170 200 250 270 325 400 *500 *625 *1250 *2500 *12500

Dredge Pump

Medium Gravel Fine Gravel Very Fine Gravel Very Coarse Sand Coarse Sand Medium Sand

Hard Iron SRL-XT Sand & Gravel Pump Severe Pump

SRL-C

Duty Slurry

Sand Pump SRL/ SRL-C Slurry Pump

Fine Sand Silt Slimes

Pulverized

Ceramic Lined

Mud Clay

* Theoretical values Micron = .001 mm

NOTE: This tabulation is for general guidance only since the selection of pump type and materials of construction also depends on the total head to be generated and the abrasivity of the slurry i.e. concentration, solids specific gravity, etc. Fig. C

1183

TECH-D

Solids and Slurries

U.S. Bureau of Standard Screens Aperture

Standard Screen Sizes Comparison Chart

Tyler Screens Aperture Mesh Double Tyler Series 31/2 5 7 9 12 5 6 7 8 10 12 14 16 24 32 42 60 80 115 170 250 325 Fig. D 16 18 22 25 30 36 44 52 60 72 85 100 120 150 170 200 240 300 .1320 .1107 .0949 .0810 0.660 .0553 .0474 .0395 .0336 .0275 .0236 .0197 .0166 .0139 .0166 .0099 .0083 .0070 .0060 .0049 .0041 .0035 .0030 .0026 .0021 3.34 2.81 2.41 2.05 1.67 1.40 1.20 1.00 .85 .70 .60 .50 .421 .353 .295 .252 .211 .177 .152 .125 .105 .088 .076 .065 .053 British Standard Screens Apeture I.M.M. Screens Aperture

Mesh 3 31/2 4 5 6 7 8 10 12 14 16 18 20 25 30 35 40 45 50 60 70 80 100 120 140 170 200 230 270 325

Inches .265 .223 .187 .157 .132 .111 .0937 .0787 .0661 .0555 .0469 .0394 .0331 .0280 .0232 .0197 .0165 .0138 .0117 .0098 .0083 .0070 .0059 .0049 .0041 .0035 .0029 .0024 .0021 .0017

mm 6.73 5.66 4.76 4.00 3.36 2.83 2.38 2.00 1.68 1.41 1.19 1.00 .84 .71 .59 .50 .42 .35 .297 .250 .210 .177 .149 .125 .105 .088 .074 .062 .053 .044

Mesh 21/2 3 4 6 8 10

Inches .321 .263 .221 .185 .156 .131 .110 .093 .078 .065 .055

mm 7.925 6.680 5.613 4.699 3.962 3.327 2.794 2.362 1.981 1.651 1.397 1.168 .991 .883 .701 .589 .495 .417 .351 .295 .246 .208 .175 .147 .124 .104 .088 .074 .061 .053 .043 .037

Mesh

Inches

mm

Mesh

Inches

mm

5 8 10 12 16 20 25 30 35 40 50 60 70 80 90 100 120 150 170 200

.100 .062 .050 .0416 .0312 .025 .020 .0166 .0142 .0125 .01 .0083 .0071 .0062 .0055 .0050 .0042 .0033 .0029 .0025

2.54 1.574 1.270 1.056 .792 .635 .508 .421 .361 .317 .254 .211 .180 .157 .139 .127 .107 .084 .074 .063

14 20

.046 .039 .0328 .0276

28 35 48 65 100 150 200 270 400

.0232 .0195 .0164 .0138 .0116 .0097 .0082 .0069 .0058 .0049 .0041 .0035 .0029 .0024 .0021 .0017 .0015

TECH-D

1184

Solids and Slurries

Aluminum Amber Ambylgonite Andesine Aragonite, CaCO3 Argentite Asbestos Asphaltum Asphalt Rock Barite Basalt Bauxite Bentonite Bertrandite Beryl Biotite Bone Borax Bornite Braggite Braunite Brick Calcite Carnotite Cassiterite Material

Specific Gravities of Rocks, Minerals and Ores

Specific Gravity Mohs Hardness 2.55- 2.75 1.06-1.11 3-3.1 2.66- 2.94 2.94-2.95 7.2-7.4 2.1-2.4 1.1-1.5 2.41 4.5 2.4-3.1 2.55-2.73 1.6 2.6 2.66- 2.83 2.7-3.1 1.7-2 1.71-1.73 5.06-5.08 10 4.72- 4.83 1.4-2.2 2.72-2.94 2.47 6.99-7.12 5.5-6 6-6.5 3.5-4 2-2.5 2 3-3.5 8-9 6 7.5-8 2.5-3 1-2 Hessite Ice Ilmenite Iron, Slag Lepidolite Lime, slaked Limestone Limonite Linnaeite Magnetite Manganite Marble Marl Millerite Monazite Molybdenite Muscovite Niccolite Orpiment Pentlandite Petalite Phosophite Phosphorus, white Polybasite Material Specific Gravity Mohs Hardness 8.24- 8.45 0.917 4.68-4.76 2.5-3 2.8-2.9 1.3- 1.4 2.4-2.7 3.6-4 4.89 4.9-5.2 4.3-4.4 2.5-2.78 2.23 5.3-5.7 5.1 4.62-4.73 2.77- 2.88 7.784 3.5 4.8 2.412-2.422 3.21 1.83 6-6.2 Porphyry 2.2 4.21-4.25 5.57 4.71 0.37-0.9 5.85 4.95-5.1 4.8 2.5-2.8 2.68 3.56 3.7 3.57-3.76 4.2-5.5 1.7-3.2 2-3.2 6.08-6.12 2.6-3 2.5 1.6-2.9 3.9-4 2.21 2-3.9 2.8-2.9 6.48 2.6-2.8 2.2 10.58 3.03-3.22 3.9-4.1 4.3-4.5 1.53 4.61-4.65 1.59 1.93-2.07 8.161 3.18 0.94 7.9-8 4.6-5.1 3.5 2.79 8-11 4.29-4.3 7.12-7.51 4.02 5.64-5.68 5-6 2-3

2-5

2.5-4

Celluloid Cerussite Chalcocite Chalcopyrite Chalk Charcoal, Pine Charcoal, Oak Chromite Chrysoberyl Cinnabar Clay Coal, Anthracite Coal, Bituminous Coal, Lignite Cobaltite Coke Colemanite Columbite Copper Cork Covellite Cuprite Diabase Diatomaceous Earth Diorite Dolomite Enargite Epidote Feldspar Fluorite Fly Ash Galena Glass Goethite Gold Granite Graphite Gravel, Dry Gravel, Wet Gypsum Halite Hausmannite Helvite Hematite

Carbon, Amorphous Graphitic

1.4 6.5- 6.57 5.5-5.8 4.1-4.3 1.9-2.8 0.28-0.44 0.47-0.57 4.5 3.65-3.85 8.09 1.8-2.6 1.4-1.8 1.2-1.5 1.1-1.4 6.2 1-1.7 1.73 5.15-5.25 8.95 0.22-0.26 4.6-4.76 6 2.94 0.4-0.72 2.86 2.8-2.86 4.4-4.5 3.25-3.5 2.55-2.75 3.18 2.07 7.3-7.6 2.4-2.8 3.3-4.3 19.3 2.6-2.9 2.2-2.72 1.55 2 2.3-2.37 2.2 4.83-4.85 3.2-3.44 4.9-5.3

1.88-2.25

3 1-2 6-7

6-6.5

2-2.5 3

3-3.5 5 1-1.5 2.5-3 5-5.5 1.5-2 2.5-3 6.5

5.5-6.5 4 4

3-3.5 2.5-3 3.5-4 5.5 8.5 2-2.5 2 2 5.5

4.5 6 2.5-3 1.5-2 3.5-4 3.5-4 3 6

2 2.5 5.5 6 5-6

1-2 4-5

2.5-2.75 7 5-5.5 2.5-3

Fig. E

Potash Powellite Proustiie Psilomelane Pumice Pyragyrite Pyrites Pyrolusite Quartz Quartzite Realgar Rhodochrosite Rhodonite Rutile Sand (see Quartz) Sandstone Scheelite Schist Serpentine Shale Siderite Silica, fused trans. Slag, Furnace Slate Smaltite Soapstone, talc Sodium Nitrate Sperrylite Spodumene Sphalerite Stannite Starch Stibnite Sugar Sulfur Sylvanite Taconite Tallow, beef Tantalite Tetrahedrite Titanite Trap Rock Uraninite Witherite Wolframite Zinc Blende Zincite

2.3 2.6-2.9 3.5-4 2-2.5 5-6

4-4.5

2.5-3.5

2.5 3.5-4.5 6-6.5 7-8 7 1.5-2 3.5-4 5.5-6.5 6-6.5 7 7 4.5-5

1.5-2.5 1.5-2 6.5 3-4.5 5-6 3.5 4-4.5 4 4

6-7 6.5-7 3.5-4 4

1185

TECH-D

Solids and Slurries

Miller Number Data
Miller Number
15 22 34 35 39 41 Kaolin Coal (clean) Limestone Clay Bauxite Gypsum

Material

Miller Number
49 56 70 84 90 103

Hardness Conversion Table for Carbon and Alloy Steels

Brinell Hardness Number (Carbide Ball) 722 688 654 615 577 543 512 481 455 443 432 421 409 400 309 381 371 362 353 344 336 327 319 311 301 294 286 279 271 264 258 253 247 243 240 234 222 210 200 195 185 176 169 C Scale 66 64 62 60 58 56 54 52 50 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A Scale 84.5 83.4 82.3 81.2 80.1 79 78 76.8 75.9 74.7 74.1 73.6 73.1 72.5 72 71.5 70.9 70.4 69.9 69.4 68.9 68.4 67.9 67.4 66.8 66.3 65.8 65.3 64.6 64.3 63.8 63.3 62.8 62.4 62 15N Scale Superficial 92.5 91.8 91.1 90.2 89.3 88.3 87.4 86.4 85.5 84.5 83.9 83.5 83 82.5 82 81.5 80.9 80.4 79.9 79.4 78.8 78.3 77.7 77.2 76.6 76.1 75.6 75 74.5 73.9 73.3 72.8 72.2 71.6 71

Ash (fly) Shale, Raw Coal Copper Conc. Magnite Phosphate Iron Ore Fig. F

Material

Miller Number
112 194 219 287

Material

Clean Sand Pyrite Tailings (various) Copper Ore

Rockwell Hardness Numbers 30T Scale Superficial

Tensile Strength

B Scale

ksl

MPa

100 99 97 95 93 92 90 88 86 Fig. G

83.1 82.5 81.1 79.8 78.4 77.8 76.4 75.1 73.8

313 292 273 255 238 229 221 215 208 201 194 188 182 177 171 166 161 156 152 149 146 141 138 135 131 128 125 123 119 117 116 114 104 100 94 92 89 86 83

2160 2010 1880 1760 1640 1580 1520 1480 1430 1390 1340 1300 1250 1220 1180 1140 1110 1080 1050 1030 1010 970 950 930 900 880 860 850 820 810 800 785 715 690 650 635 615 590 570

TECH-D

1186

Solids and Slurries

Slurry Pump Materials
MTL CODE 1002 1228 COMMON NAME Cast Iron HC600 CD4MCu 316SS ASTM NUMBER A48 CI. 35B A532 CI. III Type A A743 GR. CF-8M A734 Gr. CD4MCu BRINELL HARDNESS 196-228 550-650 Offers moderate resistance to abrasion and corrosion. It is suitable for light slurry applications, particularly those for intermittent service. Used for high corrosive, mildly abrasive applications. This is a high strength corrosion resistant alloy for mildly abrasive applications. Hardened HC600 (High Chromium Iron) CHARACTERISTICS AND TYPICAL APPLICATIONS pH RANGE 6-9 5-12

1247

1245

159-190 224-325

3-11

MTL CODE 1002 1228 1245 1247

23.0-28.0 18.0-21.0 25.0-27.0

Cr

15 Max 9.0-12.0 5.0-6.0

Ni

3.25-3.35 2.3-3.0 0.08 Max 0.4 Max

PRINCIPAL ALLOYING ELEMENTS (%, Bal Fe) C Mn Si 0.45-0.70 0.5-1.5 1.5 Max 1.70-1.90 1.0 Max 2.0 Max -

1.5 Max 2.0-3.0 2.0

Mo

Others Cu 3.0

Slurry Pump Application Guidelines

Solid Size Larger 1/4" Solids Size 1/2" Smaller Impeller Tip Speed > 5500 FPM (High Head) Solids Size Larger than 1/2"

Fig. H

Slurry
Slurry Contains Entrained Air (Froth)

Solids Size 1/4" Smaller Solids Sharp & Angular Solids Round in Shape

Slurry Contains Stringy Material

5500/5500S/ 5500LS

5500/5500S/ 5500LS, JC, SRL-XT (with metal Inpeller)

SRL, SRL-C (with froth factor sizing)

SRL-S (Shearpeller), HS

Solids Round in Shape

Solids Sharp & Angular

Class 3

Class 1, 2

SRL-XT 5500/5500S/ 5500LS

5500/5500S/ 5500LS

SRL-C

SRL SRL-C

SRL-C/SRL-XT With Metal or Urethane Impellers or Series Operation

1187

TECH-D

TECH-D-8D Abrasive Slurries and Pump Wear

The rate of wear is directly affected by the system operating point relative to the selected pumps best efficiency point. Operating the pump outside of the recommended range relative to the BEP can cause excessive wear due to recirculation or high velocity within the pump that would not be present if the pump was sized properly relative to the system. The following chart specifies the recommended operating range as a % of BEP (by flow) by slurry class: Slurry Class 1 30-130% Slurry Class 2 40-120% Slurry Class 3 50-110% Slurry Class 4 60-100% THE EFFECTS OF OPERATING AT DIFFERENT ZONES ON THE PUMP CHARACTERISTIC CURVE Reduced Capacity Operation: The velocities within the pump are low, separation and recirculation occurs, causing excessive wear. Reducing the capacity should be limited because a certain minimum velocity must be maintained to avoid settling out; with the consequence of increased wear and clogging. The hydraulic radial loads will increase and the pump efficiency will decrease. This is the point of zero flow, and pump should not be operated at this point for any length of time. Wear and tear will be rapid due to separation and recirculation, the hydraulic forces will be at their highest, and settlement and plugging will occur. The pump will rapidly heat up, which is particularly serious in rubber constructed pumps.

Recommended operating point (% BEP)

Shut Valve Operation:

In addition to operating range, wear in slurry pumps is also dependent upon tip speed and the resulting head generated by the pump in question. As impeller tip speed increases, wear due to slurry abrasion and erosion increases. The following tables provide guidelines for total head generated per pump and maximum tip speed by slurry class: Slurry Class 1 8500 (43) Slurry Class 2 7500 (38) Slurry Class 3 6500 (33) Slurry Class 4 5500 (28)

PRINCIPAL WEAR AREAS

As the abrasive mixture passes through the pump, all the wetted surfaces which come in contact will be subject to varying degrees of wear. It is very important to note that the performance of a conventional centrifugal pump, which has been misapplied to a slurry service, will be significantly effected by a relatively small degree of abrasive wear. The areas most prone to wear, in order of increasing severity, are: 1. Suction sideplate, particularly at the nozzle region.

Metal pump maximum impeller tip speed, ft/min (m/s)

2. Impeller, particularly at the eye vane inlets, suction side impeller shroud, and the vane tips. 3. Casing cutwater and side walls adjacent to the impeller tip. 4. Stuffing box packing and sleeve.

Elastomer pump maximum impeller tip speed, ft/min (m/s)

6000 (31)

5500 (28)

5000 (26)

4500 (23)

NOTE: In the case of a conventional pump with radial wear rings on the impeller, this is where the worst wear occurs.

NOTE: Check maximum operating speed of pump and impeller prior to selecting operating point. An additional application rule is that slurry pumps with elastomer liners and metal impellers should not be applied to duties requiring more than 190 ft (58m) of head per stage. If more than 190 ft of head per stage is required, an all-metal pump should be selected. Overcapacity Operation: The velocities within the pump are usually very high and recirculation occurs causing excessive wear. The radial hydraulic loads on the impeller increase.

Elastomer liner, metal impeller maximum impeller tip speed, ft/min (m/s)

6250 (32)

5750 (29)

5250 (27)

4750 (24)

On severely abrasive services where there are high concentrations of hard, larger, sharp particles, the suction side liner life can be increased if it is rotated periodically to equalize the effects of wear. Regular impeller adjustment also assists in mitigating suction side liner wear. In hard iron pumps applied to severely abrasive service, the relative wear rates of the suction side liner, casing, and impeller are in the order of 3 to 1.5 to 1, e.g. the life of the casing is three times that of a suction side wear plate.

Recognizing that due to the nature of the mixtures being pumped, the complete elimination of wear is impossible, the life of the parts can be appreciably prolonged and the cost of maintenance reduced by a good pump design and selection, e.g.: Construct the pump with good abrasion resistant materials Provide generous wear allowances on all parts subject to excessive wear Adopt a hydraulic design which will minimize the effects causing wear

Recommended The velocities within the pump are reduced (but not Operation: enough to cause settlement). Recirculation is minimal and the flow in the suction nozzle should be axial (no induced vortex). The radial hydraulic loads are minimized.

Adopt a mechanical design which is suitable for the materials of construction and has ready access to the parts for renewal Limit the head to be generated and select a low speed pump Adjust pump regularly to compensate for wear

TECH-D

1188

TECH-D-9 Vapor Pressure Various Liquids

1189

TECH-D

ABSOLUTE PRESSURELBS. PER SQ. IN.

TECH-D-9 Vapor Pressure Various Liquids

TECH-D
VACUUMINCHES OF MERCURY GAUGE PRESSURELBS. PER SQ. IN.

1190

TECH-E-1 Paper Stock Discussion

SUCTION PIPING

Section TECH-E Paper Stock

AIR IN STOCK Entrained air is detrimental to good operation of any centrifugal pump, and can result in reduced capacity, increased erosion and shaft breakage. Obviously every effort must be made to prevent the over-entrainment of air throughout the process. EXCESSIVE DISCHARGE THROTTLING While it is realized that excess capacity is normally required over the paper machine output in tons per day, "over-selection" of pumps on the basis of capacity and head usually results in the necessity of throttling the pump at the valve in the discharge line. Since the valve is normally located adjacent to the pump, the restriction of the valve and the high velocity within the valve will result in some dehydration and cause vibration due to slugs of stock. Vibration at the valve due to throttling is transmitted to the pump and may reduce the normal life of the pump-rotating element. Centrifugal pumps operating at greatly reduced capacity have more severe loading internally due to hydraulic radial thrust. Hence pumps selected too greatly oversize in both capacity and head have the combination of the vibration due to throttling plus the greater internal radial load acting to reduce the life of the rotating element. As a general rule, stock pumps should not be operated for extended periods at less than one quarter of their capacity at maximum efficiency. When excessive throttling is required, one of the two methods below should be employed. 1. Review capacity requirements and check the static and friction head required for the capacity desired. Reduce the impeller diameter to meet the maximum operating conditions. This will also result in considerable power saving.

Centrifugal pumps are used with complete success in handling paper stock and other fibrous suspensions. However, the nature of a stock suspension requires certain special considerations. All of the factors affecting pump operation discussed below must be carefully considered for a good installation. The stock must be delivered freely to the impeller for the pump to operate. The suction pipe should be as short and direct as possible. The suction pipe and entrance from the stock chest should never be smaller than the pump suction connection, and should be level with no air pockets. Always keep the direction of flow in a straight line. Inadequate suction design with undersize pipe and excessive fittings can prevent the pump from delivering rated capacity, or from operating at all on high consistency stocks. SUCTION HEAD

Stock pumps will not operate when a vacuum is required to maintain flow into the pump. Thus, there must be a static suction head sufficient to overcome suction line friction losses. PERCENT CONSISTENCY The consistency of a pulp and water suspension is the percent by weight of pulp in the mixture. Oven Dry (O.D.) consistency is the amount of pulp left in a sample after drying in an oven at 212F. Air Dry (A.D.) consistency is an arbitrary convention used by papermakers, and is the amount of pulp left in a sample after drying in atmosphere. Air Dry stock contains 10% more moisture than Bone Dry stock, i.e. 6% O.D. is 6.67% A.D. Traditional paper stock pumps will handle stock up to approximately 6% O.D. consistency. The absolute maximum limit is a function of many factors including stock fiber length, pulping process, degree of refining, available suction head, etc. In certain situations, consistencies as high as 8% O.D. can be successfully handled with a standard paper stock pump.

Recent testing on various types of stock has indicated that pump performance is the same as on water for stock consistencies up to 6% O.D. In other words, water curves can be used to select stock pumps, as the capacity, head and efficiency are the same as for water. Medium consistency paper stock is a term generally used to describe stock between 7% and 15% O.D. consistency. Pumping of medium consistency paper stock with a centrifugal pump is possible, but requires a special design due to the fiber network strength and the inherently high air content.

2. Install a by-pass line upstream from the discharge valve back to the suction chest below the minimum chest level, if possible, and at a point opposite the chest opening to the pump suction. This by-pass line should include a valve for flow regulation. This method is suggested where mill production includes variation in weight of sheet. FILLERS AND ADDITIVES The presence of fillers and chemical additives such as clay, size and caustics can materially increase the ability of paper stock to remain in suspension. However, overdosing with additives such as alum may cause gas formation on the stock fibers resulting in interruption of pumping.

1191

TECH-E

TECH-E-2 Conversion Chart of Mill Output in Tons per 24 Hours

To U.S. Gallons per Minute of Paper Stock of Various Densities

EXAMPLE:

Find the capacity in gallons per minute of a pump handling 4% stock for a mill producing 200 tons per 24 hours.

Enter chart at 200 tons per day, read horizontally to 4% stock, then downward to find pump capacity of 840 GPM.

TECH-E-2.1 Definitions / Conversion Factors

A.D. = Air Dry stock (Contains 10% Water) A.D. = 1.11 x O.D. O.D. = 0.90 x A.D. O.D. = Oven Dry stock (All Water Removed) Also Called Bone Dry (B.D.) A.D. = 1.11 O.D.T/ D

T/ D or TPD or S. T/ D = Short Tons Per Day M. T/ D = Metric Tons per Day One Short Ton = 2000 lbs.

A.D.S. T/ D = Air Dry Short Tons/Day S. T/ D = 1.1025 x M. T/ D

One Metric Ton = 2205 lbs.

O.D. = 0.90 x A.D. T/ D

A.D.M. T/ D = Alr Dry Metric Tons/Day Production in A. D. S. T/ D x 15 = Flow in GPM % O.D. Cons. Production in A. D. S. T/ D x 16.67 = Flow in GPM % A.D. Cons.

A.D. Consistency = 1.11 x O.D. Consistency

O.D. Consistency = 0.90 x A.D. Consistency

TECH-E

1192

TECH-E-3 Friction Loss of Pulp Suspensions in Pipe

I. INTRODUCTION In any stock piping system, the pump provides flow and develops hydraulic pressure (head) to overcome the differential in head between two points. This total head differential consists of pressure head, static head, velocity head and total friction head produced by friction between the pulp suspension and the pipe, bends, and fittings. The total friction head is the most difficult to determine because of the complex, nonlinear nature of the friction loss curve. This curve can be affected by many factors. The following analytical method for determining pipe friction loss is based on the published TAPPI Technical Information Sheet

(TIS) 408-4 (Reference 1), and is applicable to stock consistencies (oven-dried) from 2 to 6 percent. Normally, stock consistencies of less than 2% (oven-dried) are considered to have the same friction loss characteristic as water. The friction loss of pulp suspensions in pipe, as presented here, is intended to supersede the various methods previously issued.

Fig. 1 and Fig. 2 show typical friction loss curves for two different consistencies (C2>C1) of chemical pulp and mechanical pulp, respectively.

II. BACKGROUND

Fig. 1 Friction loss curves for chemical pulp (C2 > C1). The friction loss curve for chemical pulp can be conveniently divided into three regions, as illustrated by the shaded areas of Fig. 3.

Fig. 2 Friction loss curves for mechanical pulp (C2 > C1).

Fig. 3 Friction loss curves for chemical pulp, shaded to show individual regions.

Fig. 4 Friction loss curves for mechanical pulp, shaded to show individual regions.

1193

TECH-E

These regions shown in Fig. 3 may be described as follows:

Region 2 (Curve BCD) shows an initial decrease in friction loss (to Point C) after which the friction loss again increases. The intersection of the pulp friction loss curve and the water friction loss curve (Point D) is termed the onset of drag reduction. The velocity at this point is designated Vw.

Region 1 (Curve AB) is a linear region where friction loss for a given pulp is a function of consistency, velocity, and pipe diameter. The velocity at the upper limit of this linear region (Point B) is designated Vmax.

IV. PIPE FRICTION ESTIMATION PROCEDURE

The bulk velocity (V) will depend on the daily mass flow rate and the pipe diameter (D) selected. The final value of V can be optimized to give the lowest capital investment and operating cost with due consideration of future demands or possible system expansion.

Region 3 (Curve DE) shows the friction loss curve for pulp fiber suspensions below the water curve. This is due to a phenomenon called drag reduction. Reference 2 describes the mechanisms which occur in this region. Regions 2 and 3 are separated by the friction loss curve for water, which is a straight line with a slope approximately equal to 2. Regions 1 and 3. For this pulp type, the friction loss curve crosses the water curve at VW and there is no true Vmax. The friction loss curve for mechanical pulp, as illustrated in Fig. 4, is divided into only two regions:

The bulk velocity will fall into one of the regions previously discussed. Once it has been determined in which region the design velocity will occur, the appropriate correlations for determining pipe friction loss value(s) may be selected. The following describes the procedure to be used for estimating pipe friction loss in each of the regions. Region 1 The upper limit of Region 1 in Figure 3 (Point B) is designated Vmax. The value of Vmax is determined using Equation 1 and data given in Table I or IA. Vmax = K' C (ft/s), where K' = numerical coefficient (constant for a given pulp is attained from Table I or IA. 1

III. DESIGN PARAMETERS

To determine the pipe friction loss component for a specified design basis (usually daily mass flow rate), the following parameters must be defined: a) Pulp Type - Chemical or mechanical pulp, long or short fibered, never dried or dried and reslurried, etc. This is required to choose the proper coefficients which define the pulp friction curve.

It the proposed design velocity (V) is less than Vmax, the value of flow resistance (H/ L) may be calculated using Equation 2 and data given in Table II or IIA, and the appendices. where F = factor to correct for temperature, pipe roughness, pulp type, freeness, or safety factor (refer to Appendix D), V = bulk velocity (ft/s), H/L = F K V C Dy (ft/100 ft), 2

= exponent (constant for a given pulp), obtained from Table I or IA.

C = consistency (oven-dried, expressed as a percentage, not decimally), and

b)

c)

Consistency, C (oven-dried) - Often a design constraint in an existing system. NOTE: If air-dried consistency is known, multiply by 0.9 to convert to oven-dried consistency. Internal pipe diameter, D - Lowering D reduces initial capital investment, but increases pump operating costs. Once the pipe diameter is selected, it fixes the velocity for a prespecified mass flow rate.

K = numerical coefficient (constant for a given pulp), obtained from Table II or IIA, C = consistency (oven-dried, expressed as a percentage, not decimally),

d) e) f) g)

Bulk velocity, V - Usually based on a prespecified daily mass flow rate. Note that both V and D are interdependent for a constant mass flow rate.

Stock temperature, T - Required to adjust for the effect of changes in viscosity of water (the suspending medium) on pipe friction loss. Freeness - Used to indicate the degree of refining or to define the pulp for comparison purposes. Pipe material - Important to specify design correlations and compare design values.

For mechanical pumps, there is no true Vmax. The upper limit of the correlation equation (Equation 2 ) is also given by Equation 1 . In this case, the upper velocity is actually Vw. Region 2 The lower limit of Region 2 in Fig. 3 (Point B) is Vmax and the upper limit (Point D) is Vw. The velocity of the stock at the onset of drag reduction is determined using Equation 3 where C = consistency (oven-dried, expressed as a percentage, not decimally). 3

, , y =exponents (constant for a given pulp), obtained from Table II or IIA.

D = pipe inside diameter (in), and

VW = 4.00 C1.40 (ft/s),

If V is between Vmax and Vw, Equation 2 may be used to determine H/ L at the maximum point (Vmax). Because the system must cope with the worst flow condition, H/ L at the maximum point (Vmax) can be used for all design velocities between Vmax and Vw.

TECH-E

1194

Region 3 A conservative estimate of friction loss is obtained by using the water curve. (H/ L)w can be obtained from a Friction Factor vs. Reynolds Number plot (Reference 3, for example), or approximated from the following equation (based on the Blasius equation). where V = bulk velocity (ft/s), and D = pipe diameter (in). (H/ L)w = 0.58. V1.75 D-1.25 (ft/100 ft), 4

APPENDIX A

When metric (SI) units are utilized, the following replace the corresponding equations in the main text. where K = numerical coefficient (constant for a given pulp), obtained from Table I or IA, Vmax = K' C (m/s)
1M

Previously published methods for calculating pipe friction loss of pulp suspensions gave a very conservative estimate of head loss. The method just described gives a more accurate estimate of head loss due to friction, and has been used successfully in systems in North America and world-wide.

C = consistency (oven-dried, expressed as a percentage, not decimally), and

Please refer to Appendix A for equivalent equations for use with metric (SI) units. Tables I and IA are located in Appendix B; Tables II and IIA are located in Appendix C. Pertinent equations, in addition to those herein presented, are located in Appendix D. Example problems are located in Appendix E. V. HEAD LOSSES IN BENDS AND FITTINGS The friction head loss of pulp suspensions in bends and fittings may be determined from the basic equation for head loss, Equation 5 . H = K V12/ 2g (ft), where K = loss coefficient for a given fitting, V1 = inlet velocity (ft/s), and g = acceleration due to gravity (32.2 ft/s2). 5

where F = factor to correct for temperature, pipe roughness, pulp type, freeness, or safety factor (refer to Appendix D), K = numerical coefficient (constant for a given pulp), obtained from Table II or IIA, V = bulk velocity (m/s),

H/ L = F K V C D y (m/100m),

= exponent (constant for a given pulp), obtained from Table I or IA.

2M

C = consistency (oven-dried, expressed as a percentage, not decimally),

, , y = exponents (constant for a given pulp), obtained from Table II or IIA.

VW = 1.22 C1.40 (m/s), where C = consistency (oven-dried, expressed as a percentage, not decimally). (H/ L)w = 264 V1.75 D -1.25 (m/100m),

D = pipe inside diameter (mm), and

3M

Values of K for the flow of water through various types of bends and fittings are tabulated in numerous reference sources (Reference 3, for example). The loss coefficient for valves may be obtained from the valve manufacturer.

where V = bulk velocity (m/s), and

4M

D = pipe inside diameter (mm).

The loss coefficient for pulp suspensions in a given bend or fitting generally exceeds the loss coefficient for water in the same bend or fitting. As an approximate rule, the loss coefficient (K) increases 20 percent for each 1 percent increase in oven-dried stock consistency. Please note that this is an approximation; actual values of K may differ, depending on the type of bend or fitting under consideration (4).

H = K V12/ 2g (m), where K = loss coefficient for a given fitting, g = acceleration due to gravity (9.81 m/s2). V1 = inlet velocity (m/s), and

5M

1195

TECH-E

APPENDIX B
TABLE I Data for use with Equation 1 or Equation 1M to determine velocity limit, Vmax (1). Unbeaten aspen sulfite never dried Long fibered kraft never dried CSF = 725 (6) Long fibered kraft never dried CSF = 650 (6) Long fibered kraft never dried CSF = 550 (6) Long fibered kraft never dried CSF = 260 (6) Bleached kraft never dried and reslurried (6) Long fibered kraft dried and reslurried (6) Kraft birch dried and reslurried (6) Stone groundwood CSF = 114 Refiner groundwood CSF = 150 Newsprint broke CSF = 75 Refiner groundwood (hardboard) Refiner groundwood (insulating board) Hardwood NSSC CSF = 620 Pulp Type Stainless Steel PVC Stainless Steel PVC PVC PVC PVC Stainless Steel PVC PVC PVC PVC PVC PVC PVC PVC Pipe Material 0.85 (0.26) 0.98 (0.3) 0.89 (0.27) 0.85 (0.26) 0.75 (0.23) 0.75 (0.23) 0.79 (0.24) 0.59 (0.18) 0.49 (0.15) 0.69 (0.21) 4.0 (1.22) 4.0 (1.22) 4.0 (1.22) 4.0 (1.22) 4.0 (1.22) 0.59 (0.18) K' 1.6 1.85 1.5 1.9 1.65 1.8 1.5 1.45 1.8 1.3 1.40 1.40 1.40 1.40 1.40 1.8

NOTES: 1. When metric (SI) units are utilized, use the value of K' given in parentheses. When the metric values are used, diameter (D) must be in millimeters (mm) and velocity (V) in meters per second (m/s). 2. Original data obtained in stainless steel and PVC pipe. PVC is taken to be hydraulically smooth pipe. 3. Stainless steel may be hydraulically smooth although some manufacturing processes may destroy the surface and hydraulic smoothness is lost. 4. For cast iron and galvanized pipe, the K' values will be reduced. No systematic data are available for the effects of surface roughness. 5. If pulps are not identical to those shown, some engineering judgement is required. 6. Wood is New Zealand Kraft pulp.

TABLE IA Data (5, 6) for use with Equation 1 or Equation 1M determine velocity limit, Vmax. Unbleached sulphite Bleached sulphite Kraft Bleached straw Unbleached straw Pulp Type (5) Pipe Material Copper Copper Copper Copper Copper 0.98 0.98 0.98 0.98 0.98 K' (0.3) (0.3) (0.3) (0.3) (0.3) 1.2 1.2 1.2 1.2 1.2

Estimates for other pulps based on published literature. Pulp Type (5, 6)

Cooked groundwood Soda NOTE:

Pipe Material Copper Steel

When metric (SI) units are utilized, use the value of K' given in parentheses. When the metric values are used, diameter (D) must be millimeters (mm) and velocity (V) in meters per second (m/s)

0.75 (0.23) 4.0 (1.22)

K'

1.8 1.4

TECH-E

1196

APPENDIX C
TABLE II Data for use with Equation 2 or Equation 2M to determine head loss, H/ L (1). Pulp Type K

NOTES: 1. When metric (SI) units are utilized, use the value of K given in parentheses. When the metric values are used, diameter (D) must be in millimeters (mm) and velocity must be in meters per second (m/s). 2. Original data obtained in stainless steel and PVC pipe (7,8, 9). 3. No safety factors are included in the above correlations. 4. The friction loss depends considerably on the condition of the inside of the pipe surface (10). 5. Wood is New Zealand Kraft pulp. TABLE IIA Data (5, 6) for use with Equation 2 or Equation 2M to determine head loss, H/ L. Pulp Type (5) K

Unbeaten aspen sulfite never dried Long fibered kraft never dried CSF = 725 (5) Long fibered kraft never dried CSF = 650 (5) Long fibered kraft never dried CSF = 550 (5) Long fibered kraft never dried CSF = 260 (5) Bleached kraft bleached and reslurred (5) Long fibered kraft dried and reslurred (5) Kraft birch dried and reslurred (5) Stone groundwood CSF = 114 Refiner groundwood CSF = 150 Newspaper broke CSF = 75 Refiner groundwood CSF (hardboard) Refiner groundwood CSF (insulating board) Hardwood NSSF CSF = 620

5.30 (235) 11.80 (1301) 11.30 (1246) 12.10 (1334) 17.00 (1874) 8.80 (970) 9.40 (1036) 5.20 (236) 3.81 (82) 3.40 (143) 5.19 (113) 2.30 (196) 1.40 (87) 4.56 (369)

0.36 0.31 0.31 0.31 0.31 0.31 0.31 0.27 0.27 0.18 0.36 0.23 0.32 0.43

2.14 1.81 1.81 1.81 1.81 1.81 1.81 1.78 2.37 2.34 1.91 2.21 2.19 2.31

-1.04 -1.34 -1.34 -1.34 -1.34 -1.34 -1.34 -1.08 -0.85 -1.09 -0.82 -1.29 -1.16 -1.20

Estimates for other pulps based on published literature.

Unbleached sulfite Bleached sulfite Kraft Bleached straw Unbleached straw

12.69 (1438) 11.40 (1291) 1140 (1291) 11.40 (1291) 5.70 (646)

0.36 0.36 0.36 0.36 0.36

1.89 1.89 1.89 1.89 1.89

-1.33 -1.33 -1.33 -1.33 -1.33

Cooked groundwood Soda NOTE:

Pulp Type (5, 6)

When metric (SI) units are utilized, use the value of K given in parentheses. When the metric values are used, diameter (D) must be millimeters (mm) and velocity (V) in meters per second (m/s) Where T.P.D. = mill capacity (metric tons per day), and C = consistency (oven-dried, expressed as a percentage, not decimally). 2. Bulk velocity, V V = 0.321 Q (ft/s), or A V = 0.4085 Q D2 (ft/s), (ii) (ii)

6.20 (501) 6.50 (288)

0.43 0.36

2.13 1.85

-1.20 -1.04

APPENDIX D

The following gives supplemental information to that where I.P.D. mill capacity (metric tons per day), provided in the main text. 1. Capacity (flow), Q Q = 16.65 (T.P.D.) (U.S. GPM), C (i)

Where T.P.D. = mill capacity (short tons per day), and C = consistency (oven-dried, expressed as a percentage, not decimally). If SI units are used, the following would apply: -3 Q = 1.157 (10 ) (T.P.D.) (m3/s), C (iM)

Where Q = capacity (U.S. GPM) A = inside area of pipe (in2), and D = inside diameter of pipe (in)

1197

TECH-E

The following would apply if SI units are used: 6 V = 1 (10 ) Q (m/s), or A

6 V = 1.273 (10 ) Q (m/s), D2

(iiM) (iiM)

APPENDIX E

The following are three examples which illustrate the method for determination of pipe friction loss in each of the three regions shown in Figure 3. Example 1. Determine the friction loss (per 100 ft of pipe) for 1000 U.S. GPM of 4.5% oven-dried unbeaten aspen sulfite stock, never dried, in 8 inch schedule 40 stainless steel pipe (pipe inside diameter = 7.981 in). Assume the pulp temperature to be 95 F. Solution: a) The bulk velocity, V, is V = 0.4085 Q, D2 (ii)

3.Multiplication Factor, F (.included in Equation 2 ) -

Where Q = capacity (m3/s), A = inside area of pipe (mm2), and D = inside diameter of pipe (mm)

F = F1 F2 F3 F4 F5, (iv) where F1 =correction factor for temperature. Friction loss calculations are normally based on a reference pulp temperature of 95 F (35C). The flow resistance may be increased or decreased by 1 percent for each 1.8F (1C) below or above 95F (35C), respectively. This may be expressed as follows: F1 = 1.528 - 0.00556 T, (v) where T = pulp temperature ( F), or F1 = 1.35 - 0.01 T, (vM) where T = pulp temperature (C). F2 = correction factor for pipe roughness. This factor may vary due to manufacturing processes of the piping, surface roughness, age, etc. Typical values for PVC and stainless steel piping are listed below: F2 = 1.0 for PVC piping, F2 = 1.25 for stainless steel piping. Please note that the above are typical values; experience and/or additional data may modify the above factors.

Vmax = K' C,

b) It must be determined in which region (1, 2, or 3) this velocity falls. Therefore, the next step is to determine the velocity at the upper limit of the linear region, Vmax. and K' = numerical coefficient = 0.85 (from Appendix B, Table I), C = consistency = 4.5%, 1

and Q = flow = 1000 U.S. GPM. D = pipe inside diameter = 7.981 in. 0.4085 (1000) = 6.41 ft/s. V= 7.9812

F4 = correction factor for beating. Data have shown that progressive beating causes, initially, a small decrease in friction loss, followed by a substantial increase. For a kraft pine pulp initially at 725 CSF and F4 = 1.0, beating caused the freeness to decrease to 636 CSF and F4 to decrease to 0.96. Progressive beating decreased the freeness to 300 CSF and increased F4 to 1.37 (see K values in Table II). Some engineering judgement may be required. F5 = design safety factor. This is usually specified by company policy with consideration given to future requirements.

F3 = correction factor for pulp type. Typical values are listed below: F3 = 1.0 for pulps that have never been dried and reslurried, F3 = 0.8 for pulps that have been dried and reslurried. NOTE: This factor has been incorporated in the numerical coefficient, K, for the pulps listed in Table II. When using Table II, F3 should not be used.

c) Since Vmax exceeds V, the friction loss, H/ L, falls within the linear region, Region 1. The friction loss is given by the correlation: and F = correction factor = F1 F2 F3 F4 F5, F1 = correction factor for pulp temperature. Since the pulp temperature is 95 F, F1 = 1.0, H/L =F K V C Dy

Vmax = 0.85 (4.51.6) = 9.43 ft/s.

= exponent = 1.6 (from Appendix B, Table I).

F2 = correction factor for pipe roughness. For stainless steel pipe, F2 = 1.25 (from Appendix D), F3 = correction factor for pulp type. Numerical coefficients for this pulp are contained in Appendix C, Table II, and have already incorporated this factor. F4 = 1.0 (from Appendix D), F5 = 1.0.

F4 = correction factor for beating. No additional beating has taken place, therefore F5 = design safety factor. This has been assumed to be unity. F = (1.0) (1.25) (1.0) (1.0) (1.0) = 1.25, K = numerical coefficient = 5.30 (from Appendix C, Table II), V, C, D have been evaluated previously. , , y = exponents = 0.36, 2.14, and -1.04, respectively (from Appendix C, Table II),

TECH-E

1198

H/ L

= (1.25) (5.30) (1.952) (25.0) (0.1153) = 37.28 ft head loss/100 ft of pipe.

= (1.25) (5.30) (6.410.36) (4.52.14) (7.981-1.04)

Example 3.

This is a rather substantial head loss, but may be acceptable for short piping runs. In a large system, the economics of initial piping costs versus power costs should be weighed, however, before using piping which gives a friction loss of this magnitude. Example 2. Determine the friction loss (per 100 ft of pipe) of 2500 U.S. GPM of 3% oven-dried bleached kraft pine, dried and reslurried, in 12 inch schedule 10 stainless steel pipe (pipe inside diameter = 12.39 in). Stock temperature is 1250F. Solution: a) V, the bulk velocity, is V = 0.4085 Q, D2

Determine the friction loss (per 100 ft of pipe) for 2% oven-dried bleached kraft pine, dried and reslurried, through 6 inch schedule 40 stainless steel pipe (inside diameter = 6.065 in). The pulp temperature is 90 F; the flow rate 1100 U.S. GPM. Solution: a)The bulk velocity is V = 0.4085 Q, D2

b) The velocity at the upper limit of the linear region, Vmax, is Vmax = K' C , and K' = 0.59 (from Appendix B, Table I), Vmax = 0.59 (3.01.45) = 2.90 ft/s. = 1.45 (from Appendix B, Table I).

= 0.4085 (2500) = 6.65 ft/s. 12.392

(ii)

Vmax = K' C ,

b) It must be determined in which region (1, 2 or 3) this velocity falls. To obtain an initial indication, determine Vmax. and K' = 0.59 (from Appendix B, Table I), Vmax = 0.59 (201.40) = 1.61 ft/s. 1 = 1.45 (from Appendix B, Table I).

= 0.4085 (1100) = 12.22 ft/s. 6.0652

(ii)

VW = 4.00 C1.40

c) Since V exceeds Vmax, Region 1 (the linear region) is eliminated. To determine whether V lies in Region 2 or 3, the velocity at the onset of drag reduction, Vw, must be calculated. = 4.00 (2.01.40) = 10.56 ft/s.

The next step requires calculation of Vw. VW = 4.00 C1.40 = 4.00 (3.01.40) = 18.62 ft/s.

c) Region 1 (the linear region) has been eliminated, since the bulk velocity, V, exceeds Vmax. 3

d) V exceeds Vw, indicating that it falls in Region 3. The friction loss is calculated as that of water flowing at the same velocity. (H/ L) w = 0.579 V1.75 D-1.25, = 0.579 (12.221.75) (6.065-1.25)

d) V exceeds Vmax, but is less than Vw, indicating that it falls in Region 2. The friction loss in this region is calculated by 2 . substituting Vmax into the equation for head loss, Equation H/ L = F K (Vmax) C Dy, and F1 F2 F3 F4 F5; F1 = 1.528 - 0.00556T, and T = stock temperature = 125 F (iv) (v)

This will be a conservative estimate, as the actual friction loss curve for pulp suspensions under these conditions will be below the water curve. REFERENCES (1) (3) (4) (5) (6) (7) (8) (9)

= 4.85 ft head loss/100 ft of pipe.

F2 = 1.25 (from Appendix D), F3 = F4 = F5 = 1.0,

F1 = 1.528 - 0.00556 (125) = 0.833,

TAPPI Technical Information Sheet (TIS) 408-4. Technical Association of the Pulp and Paper Industry, Atlanta, Georgia (1981). (2) K. Molter and G.G. Duffy, TAPPI 61,1, 63 (1978). Hydraulic Institute Engineering Data Book. First Edition, Hydraulic Institute, Cleveland, Ohio (1979). K. Molter and G. Elmqvist, TAPPI 63. 3,101 (1980). W. Brecht and H. Helte, TAPPI 33, 9, 14A (1950).

F = 0.833 (1.25) (1.0) = 1.041, , , y = H/L

K = 8.80 (from Appendix C, Table II),

Vmax, C, and D have been defined previously. = 3.19 ft head loss/100 ft of pipe.

0.31,1.81, and -1.34, respectively (from Appendix C, Table II),

R.E. Durat and L.C. Jenness. TAPPI 39, 5, 277 (1956)

K. Molter, G.G. Duffy and AL Titchener, APPITA 26, 4, 278 (1973) G.G. Duffy and A.L. Titchener, TAPPI 57, 5, 162 (1974) G.G. Duffy, K. Molter, P.F.W. Lee. and S.W.A. Milne, APPITA 27, 5, 327 (1974).

= 1.041 (8.80) (1.391) (7.304) (0.03430)

= 1.041 (8.80) (2.900.31) (3.01.81) (12.39-1.34)

(10) G.G. Duffy, TAPPI 59, 8, 124 (1976).

(11) G.G. Duffy, Company Communications. Goulds Pumps. Inc.. (1980-1981)

1199

TECH-E

TECH-E-4 Pump Types Used in the Pulp & Paper Industry

Mill Area Woodyard Typical Services Log Flume Log/Chip Pile spray Chip Washer Typical Pump Construction Al/316SS Trim AI/316SS trim Al/316SS Trim Mixed Flow Vertical Turbine Stock ANSI Double Suction Stock ANSI Double Suction Medium Consistency Hi Temp/Press Stock Pump Type MF VIT 3175, 3180/85 3196 3410, 3415, 3420 3175, 3180/85 3196 3410, 3415, 3420 3500 3181/86 Goulds Model

Pulp Mill

Bleach Plant

Stock Prep Paper Machine (Wet End) Paper Machine (Dry End) Coater

Kraft Recovery

Utility (Power House) Miscellaneous

Shower Supply Dilution Supply Screen Supply Cleaner Supply Decker Supply Hi/Med. Density Storage Transfer Medium Cons. Storage Chip Chute Circulation White Liquor Circulation Condensate Wash Liquor Circulation Brown Stock Storage Bleach Tower Storage Bleach Chemical Mixing High Density Storage Chemical Feed Washer Supply Washer Shower Water Dilution Water Medium Consistency O2 Reactor CI02 Generator Circulation Refiner Supply Deflaker Supply Machine Chest Supply Fan Pumps Couch Pit Saveall Sweetner Shower Dryer Drainage Condensate Trim Squirt Broke Chest Coating Slurries Kaolin Clay (Fillers) Weak Black Liquor Evaporator Circulation Concentrated Black Liquor Condensate Injection Black Liquor Transfer Pumps Smelt Spout Cooling Water Collection Weak Wash Scrubber Green Liquor (Storage Transfer) Lime Mud Dregs Feedwater Condensate Deaerator Booster Mill Water Supply Sump Pumps Hole/Slot Screen Supply Rejects Float Cell Medium Consistency Storage Hydro Pulper Dilution Water

Al/31SS Al316SS Al316SS 316SS 316SS/317SS 316SS/317SS Various 316SS/317SS CD4MCu CD4MCu Al/316SS 316SS 316SS 316SS 317SS, 254 SMO, Titanium 316SS/317SS 316SS 316SS 316SS 316SS 316SS Titanium 316SS 316SS 316SS Al/316SS Trim, All 316SS Al/316SS Trim, All 316SS Al/316SS Trim, All 316SS Al/316SS Trim, All 316SS A/316SS Trim, All 316SS Al/316SS Trim, Al/316SS Trim Al/316SS Trim Al/316SS Trim 316SS/CD4MCu 316SS/CD4MCu 316SS 316SS 316SS 316SS 316SS CD4MCu Al/316SS Trim Al/316SS Trim 316SS/CD4MCu/28% Chrome 316SS/CD4MCu/28% Chrome 316SS/CD4MCu/28% Chrome 316SS/CD4MCu/28% Chrome CS/Chrome Trim/All Chrome 316SS 316SS Al/316SS Trim Al/316SS Trim 316SS/CD4MCu 316SS/CD4MCu 316SS 316SS/317SS 316SS/CD4MCu Al/316SS Trim

Stock ANSI Medium Consistency Axial Flow Non-metallic

3175, 3180/85 3196 3500 AF NM 3196

ANSI 3196 Medium Duty Slurry JC ANSI 3196 Stock 3175, 3180/85 Medium Duty Slurry JC High Temp/Pressure Stock 3181/86 High Pressure 3316 Multi Stage

Double Suction Stock Low Flow High Pressure Two-Stage ANSI Low Flow Stock

Stock ANSI

3415, 3420 3175, 3180/85 LF3196 3310H 3316 3196 LF 3196 3175, 3180/85

3175, 3180/85 3196

Recycle

Multi-Stage ANSI High Pressure Vertical Can Double Suction Vertical Turbine Self-Priming Vertical Sumps Vertical Sump; Recessed Submersible Stock Recessed ANSI Medium Consistency

3700, VIC 3410, 3415, 3420 VIT 3796 3171 VHS HSU 3175, 3180/85 CV 3196,HS 3196 3500

3310H, 3600 3196

TECH-E

1200

TECH-F-1 Standard Weights and Dimensions of Mechanical Joint Cast Iron Pipe, Centrifugally Cast
Wall Weight Per Foot* 11.9 12.9 13.8 16.1 17.3 18.4 19.6 25.4 27,2 29.0 31.3 33.6 36.2 38.6 41.8 45.0 48.1 51.2 48.0 52.0 55.9 59.9 63.8 68.6 62.3 67.1 59.9 76.6 82.5 88.3 95.2 73.6 77.8 83.4 89.0 95.9 102.7 110.9 118.9 Average Thickness Class 22 23 24 22 23 24 25 22 23 24 25 26 22 23 24 25 26 27 22 23 24 25 26 27 22 23 25 25 26 27 28 21 22 23 24 25 26 27 28 Wall Weight Per Foot* 87.6 94.0 100.3 108.3 116.2 124.0 133.3 142.7 106.0 113.2 122.2 131.0 140.0 150.6 161.0 173.2 124.2 134.2 144.2 154.1 165.9 177.6 191.2 214.8 164.2 176.2 188.2 202.6 216.8 233.2 249.7 268.2

Section TECH-F Mechanical Data

Extracted from USA Standard Cast Iron Pipe Flanges and Flanged Fittings (USAS B16. 11967), with the permission of the publisher. The American Society of Mechanical Engineers, United Engineering Center, 345 East 47th Street, New York, New York 10017.

Nom. Size & (Outside Diam), In. 3 (3.96)

Thickness, In. 0.32 0.35 0.38 0.35 0.38 0.41 0.44 0.38 0.41 0.44 0.48 0.52 0.41 0.44 0.48 0.52 0.56 0.60 0.44 0.48 0.52 0.56 0.60 0.65 0.48 0.52 0.56 0.60 0.65 0.70 0.76 0.48 0.51 0.55 0.59 0.64 0.69 0.75 0.81

Nom. Size & (Outside Diam), In. 16 (17.40)

Thickness, In. 0.50 0.54 0.58 0.63 0.68 0.73 0.79 0.85 0.54 0.58 0.63 0.68 0.73 0.79 0.85 0.92 0.57 0.62 0.67 0.72 0.78 0.84 0.91 0.98 0.63 0.68 0.73 0.79 0.85 0.92 0.99 1.07

Average Thickness Class 21 22 23 24 25 26 27 28 21 22 23 24 25 26 27 28 21 22 23 24 25 26 27 28 21 22 23 24 25 26 27 28

4 (4.80) 6 (6.90)

8 (9.05)

18 (19.50)

10 (11.10)

20 (21.60)

12 (13.20)

24 (25.80)

14 (15.30)

Chart 1

*Based on 20 Ft. Laying Length of Mech. Joint Pipe including Bell.

1201

TECH-F

TECH-F-2 125 Lb. & 250 Lb. Cast Iron Pipe Flanges and Flanged Fittings
Nomi- Diam. nal of Pipe Flange Size

1 11/4 11/2 2 21/2 3 31/2 4 5 6 8 10 12 14 16 18 20 24 30 36 42 48

41/4 4 5/8 5 6 7 71/2 81/2 9 10 11 131/2 16 19 21 231/2 25 271/2 32 383/4 46 53 591/2

Thickness of Flange (Min.)

7/16 1/2 9 /16 5 /8 11 /16 3/4 13/16 15 /16 15 /16

Diam. of Bolt Circle

1 11/8 13/16 11/4 13/8 17/16 19/16 111/16 17/8 21/8 23/8 25/8 23/4

31/8 31/2 37/8 43/4 51/2 6 7 71/2 81/2 91/2 113/4 141/4 17 183/4 211/2 223/4 25 291/2 36 423/4 491/2 56

Number of Bolts

Diam. of Bolts
1 /2 1 /2 1 /2 5 /8 5 /8 5 /8 5 /8 5 /8 3 /4 3 /4 3 /4 7 /8 7 /8

4 4 4 4 4 4 8 8 8 8 8 12 12 12 16 16 20 20 28 32 36 44

Diam. of Length Drilled of Bolt Bolts Holes

5/8 5/8 5/8 3/4 3/4 3/4 3/4 3/4 7/8 7/8 7/8

1 1 11/8 11/8 11/4 11/4 11/2 11/2 11/2

1 1 11/8 11/8 11/4 11/4 13/8 13/8 13/8 13/8 13/8

13/4 2 2 21/4 21/2 21/2 23/4 3 3 31/4 31/2 33/4 33/4 41/4 41/2 43/4 5 51/2 61/4 7 71/2 73/4

ThickNomi- Diam. ness nal of of Pipe Flange Flange3 Size (Min.)

1 11/4 11/2 2 21/2 3 31/2 4 5 6 8 10 12 14 16 18 20 24 *30 *36 *42 *48

47/8 51/4 61/8 61/2 71/2 81/4 9 10 11 121/2 15 171/2 201/2 23 251/2 28 301/2 36 43 50 57 65

1 11/8 13/16 11/4 13/8 17/16 15/8 17/8 2 21/8 21/4 23/8 21/2 23/4 3 33/8 311/16 4

11/16 3/4 13/16 7/8

Diam. of Bolt Circle

31/2 37/8 41/2 5 57/8 65/8 71/4 77/8 91/4 105/8 13 151/4 173/4 201/4 221/2 243/4 27 32 391/4 46 523/2 603/4

Diam. of Bolt Holes1

3/4 3/4 7/8 3 /4 7/8 7/8 7/8 7/8 7/8 7/8

Number of Bolts1

Size of Bolt
5 /8 5 /8 3 /4 5 /8 3 /4 3 /4 3 /4 3 /4 3 /4 3 /4 7 /8

Length of Bolts2

1 11/8 1 1 /4 11/4 13/8 13/8 13/8 15/8 2 21/4 1 2 /4 21/4

4 4 4 8 8 8 8 8 8 12 12 16 16 20 20 24 24 24 28 32 36 40

1 11/8 11/8 11/4 11/4 11/4 11/2 11/2 2 2 2

21/2 21/2 23/4 23/4 31/4 31/2 31/2 3 3/4 4 4 41/2 51/4 51/2 6 61/4 61/2 63/4 73/4 81/2 91/2 101/4 103/4

Chart 2 American Standard Class 125 Cast Iron Pipe Flanges (ASA B16.1)
Nominal Pipe Size Center to Face A B C D E Face to Face F Body Wall Thick nesst
5 /16 5 /16 5 /16 5 /16 5/16 3 /8 7/16 1 /2 1 /2 9 /16 5 /8 3 /4 13/16 7 /8

Chart 3 American Standard Class 250 Cast Iron Pipe Flanges (ASA B16b)
Nomi- Inside Wall Diam. nal Diam. Thickof Pipe of ness Raised Size Fitting of Face (Min.) Body* Center to Face A B C D E Face to Face F

1 11/4 11/2 2 21/2 3 31/2 4 5 6 8 10 12 14 16 18 20 24 30 36 42 48

31/2 33/4 4 41/2 5 51/2 6 61/2 71/2 8 9 11 12 14 15 161/2 18 22 25 28* 31* 34*

5 51/2 6 61/2 7 73/4 81/2 9 101/4 111/2 14 161/2 19 211/2 24 261/2 29 34 411/2 49 561/2 64

13/4 2 21/4 21/2 3 3 31/2 4 41/2 5 51/2 61/2 71/2 71/2 8 81/2 91/2 11 15 18 21 24

53/4 61/4 7 8 1 9 /2 10 111/2 12 131/2 141/2 171/2 201/2 241/2 27 30 32 35 401/2 49 . . .

13/4 13/4 2 2 1/2 21/2 3 3 3 31/2 31/2 41/2 5 51/2 6 61/2 7 8 9 10 . . .

. . . 5 51/2 6 61/2 7 8 9 11 14 14 16 18 19 20 24 30 36 42 48

1 11/16 11/8 11/4 17/16 15/8 113/16 2

A

2 2 21/2 21/2 3 3 31/2 31/2 4 4 5 5 6 6 8 8 10 10 12 12 14 131/4 16 151/4 18 17 20 19 24 23

7 /16 1/2 9 /16 9/16 5 /8 11 /16 3 /4 13 /16 15 /16

1 11/8 11/4 13/8 11/2 15/8

4 3/16 4 15/16 5 11/16 6 5/16 615/16 8 5/16 911/16 1115/16 141/6 167/16 1815/16 211/16 235/16 259/16 301/4

5 51/2 6 61/2 7 8 81/2 10 111/2 13 15 161/2 18 191/2 221/2

6 1/2 7 73/4 81/2 9 101/4 111/2 14 16 1/2 19 211/2 24 261/2 29 34

3 31/2 31/2 4 41/2 5 51/2 6 7 8 81/2 91/2 10 101/2 12

9 101/2 11 121/2 131/2 15 171/2 201/2 24 271/2 31 341/2 371/2 401/2 471/2

21/2 21/2 3 3 3 31/2 4 5 51/2 6 61/2 71/2 8 8 1/2 10

5 51/2 6 6 1/2 7 8 9 11 12 14 16 18 19 20 24

Chart 5 American Standard Class 250 Cast Iron Flanged Fittings (ASA B16b)
A B 90 ELBOW 90 LONG RADIUS ELBOW 45 ELBOW B C C SIDE OUTLET ELBOW A

Chart 4 American Standard Class 125 Cast Iron Flanged Fittings (ASA B16.1)

A A A A TEE

A A A

A A A SIDE OUTLET TEE OR CROSS F F

90

D
E

45

DOUBLE BRANCH ELBOW

CROSS

REDUCER

ECCENTRIC REDUCER

TRUE Y

45 LATERAL

TECH-F

1202

TECH-F-3 Steel Pipe, Dimensions and Weights

Size: Nom. & (Outside Diam.), In.*
1 /8 (0.405) 1 /4 (0.540) 3 /8 (0.675) 1 /2 (0.840)

Wall Thickness, In. 0.068 0.095 0.088 0.119 0.091 0.126 0.109 0.147 0.188 0.294 0.113 0.154 0.219 0.308 0.133 0.179 0.250 0.308 0.140 0.191 0.250 0.382 0.145 0.200 0.281 0.400 0.154 0.218 0.344 0.436 0.203 0.276 0.375 0.552 0.216 0.300 0.438 0.600 0.226 0.318 0.237 0.337 0.438 0.531 0.674 0.258 0.375 0.500 0.625 0.750 0.280 0.432 0.562 0.719 0.864 0.250 0.277 0.322 0.406 0.500 0.594 0.719 0.812 0.875 0.906 0.250 0.307 0.365 0.500 0.594 0.719 0.844 1.000 1.125

Weight per Foot, Plain Ends, Lb. 0.24 0.31 0.42 0.54 0.57 0.74 0.85 1.09 1.31 1.71 1.13 1.47 1.94 2.44 1.68 2.17 2.84 2.44 2.27 3.00 3.76 5.21 2.72 3.63 4.86 6.41 3.65 5.02 7.46 9.03 5.79 7.66 10.01 13.70 7.58 10.25 14.31 18.58 9.11 12.51 10.79 14.98 18.98 22.52 27.54 14.62 20.78 27.04 32.96 38.55 18.97 28.57 36.42 45.34 53.16 22.36 24.70 28.55 35.66 43.39 50.93 45.34 67.79 72.42 74.71 28.04 34.24 40.48 54.74 64.40 77.00 89.27 104.13 115.65

Schedule No. 40 80 40 80 40 80 40 80 160 S XS S XS S XS S XS

Size: Nom. & (Outside Diam.), In.*

Wall Thickness, In. 0.250 0.330 0.375 0.406 0.500 0.562 0.688 0.844 1.000 1.125 1.312 0.250 0.312 0.375 0.438 0.500 0.594 0.750 0.938 1.094 1.250 1.406 0.250 0.312 0.375 0.500 0.656 0.844 1.031 1.219 1.438 1.594 0.250 0.312 0.375 0.438 0.500 0.562 0.750 0.938 1.156 1.375 1.562 1.781 0.250 0.375 0.500 0.594 0.812 1.031 1.281 1.500 1.750 1.969 0.250 0.375 0.500 0.875 1.125 1.375 1.625 1.875 2.125 0.250 0.375 0.250 0.375 0.500 0.562 0.688 0.969 1.219 1.531 1.812 2.062 2.344

Weight per Foot, Plain Ends, Lb. 33.38 43.77 49.56 53.56 65.42 73.22 88.57 107.29 125.49 139.68 160.33 36.71 45.68 54.57 63.37 72.09 85.01 106.13 130.79 150.76 170.22 189.15 42.05 52.36 62.58 82.77 107.54 136.58 164.86 192.40 223.57 245.22 47.39 59.03 70.59 82.06 93.45 104.76 138.17 170.84 208.00 244.14 274.30 308.55 47.39 78.60 93.45 123.06 166.50 208.92 256.15 296.37 341.10 379.14 58.07 86.61 114.81 197.42 250.82 302.88 353.61 403.01 451.07 63.41 94.62 63.41 94.62 125.49 140.80 171.17 238.29 296.53 367.45 429.50 483.24 542.09

Schedule No. 20 30

12 (12.750)

/4 (1.050)
3

1 (1.315) 11/4 (1.660) 11/2 (1.900) 2 (2.375) 21/2 (2.875) 3 (3.500)

31/2 (4.000) 4 (4.500)

5 (5.563) 6 (6.625)

8 (8.625)

10 (10.750)

XXS 40 S 80 XS 160 XXS 40 S 80 XS 160 XXS 40 S 80 XS 160 XXS 40 S 80 XS 160 XXS 40 S 80 XS 160 XXS 40 S 80 XS 160 XXS 40 S 80 XS 160 XXS 40 S 80 XS 40 S 80 XS 120 160 XXS 40 S 80 XS 120 160 XXS 40 S 80 XS 120 160 XXS 20 30 40 S 60 80 XS 100 160 140 XXS 160 20 30 40 S 60 XS 80 100 120 140 XXS 160

14 (14.000)

16 (16.000)

18 (18.000)

20 (20.000)

22 (22.000)

24 (24.000)

XS 60 80 100 120 XXS 140 160 10 20 30 S 40 XS 60 80 100 120 140 160 10 20 30 S 40 XS 60 80 100 120 140 160 10 20 S 30 XS 40 60 80 100 120 140 160 10 20 S XS 40 60 80 100 120 140 160 10 20 S 30 XS 60 80 100 120 140 160 10 20 S 10 20 S XS 30 40 60 80 100 120 140 160

40

1203

TECH-F

TECH-F-4 150 Lb. and 300 Lb. Steel Pipe Flanges and Fittings
Extracted from USA Standard Cast Iron Pipe Flanges and Flanged Fittings (USAS, B16. 5-1968), with the permission of the publisher, The American Society of Mechanical Engineers, United Engineering Center, 345 East 47th Street, New York NY 10017.
Nominal Pipe Size
1 11/4 11/2 2 21/2 3 31/2 4 5 6 8 10 12 14 16 18 20 24

AA
31/2 33/4 4 41/2 5 51/2 6 61/2 71/2 8 9 11 12 14 15 161/2 18 22

BB
5 51/2 6 61/2 7 73/4 81/2 9 101/4 111/2 14 161/2 19 211/2 24 261/2 29 34

CC
13/4 2 21/4 21/2 3 3 31/2 4 41/2 5 51/2 61/2 71/2 71/2 8 81/2 91/2 11

EE
53/4 61/4 7 8 91/2 10 111/2 12 131/2 141/2 171/2 201/2 241/2 27 30 32 35 401/2

FF
13/4 13/4 2 21/2 21/2 3 3 3 31/2 31/2 41/2 5 51/2 6 6 1/2 7 8 9

GG
41/2 41/2 41/2 5 51/2 6 61/2 7 8 9 11 12 14 16 18 19 20 24

Nomi- Diam. nal of Pipe Flange Size O

1 /2 3/4

Thickness of Flange (Min.)*

7/16 1/2 9/16 5/8 11/16 3 /4 7 /8 15/16 15/16 15 /16 15 /16

Diam. of Bolt Circle

Diam. of Bolt Holes

5/8 5/8 5/8 5/8 5/8 3/4 3/4 3 /4 3 /4 3/4 7/8 7/8 7/8

Number of Bolts

Diam. of Bolts
1 /2 1 /2 1 /2 1 /2 1 /2 5 /8 5 /8 5 /8 5 /8 5 /8 3 /4 3 /4 3 /4

1 11/4 11/2 2 21/2 3 31/2 4 5 6 8 10 12 14 16 18 20 24

31/2 37/8 41/4 45/8 5 6 7 71/2 81/2 9 10 11 131/2 16 19 21 231/2 25 271/2 32

1 11/8 13/16 11/4 13/8 17/16 19/16 111/16 17/8

23/8 21/4 31/8 31/2 37/8 43/4 51/2 6 7 71/2 81/2 91/2 113/4 141/4 17 183/4 211/4 223/4 25 291/2

11/8 11/8 11/4 11/4 3/8

1 1

4 4 4 4 4 4 4 4 8 8 8 8 8 12 12 12 16 16 20 20

Length of (with 1 16" Raised Face

7/8 7/8 1 1 11/8 11/8 11/4

13/4 2 2 2 1/4 21/4 23/4 3 3 3 3 31/4 31/4 31/2 33/4 4 41/4 41/2 43/4 51/4 53/4

Chart 8 150 Lb. Steel Flanged Fittings

AA

BB CC BB

AA AA CC AA TEE

AA ELBOW AA AA

Chart 6 150 Lb. Steel Pipe Flanges

LONG RADIUS ELBOW

45 ELBOW

Nominal Pipe Size

1 11/4 11/2 2 21/2 3 31/2 4 5 6 8 10 12 14 16 18 20 24

Flange Diam.
4 /8 51/4 61/8 61/2 71/2 81/4 9 10 11 121/2 15 171/2 201/2 23 251/2 28 301/2 36
7

Flange Thickness (Min.)*

11/16 13/16 3/4 7/8

Bolt Circle Diam.

3 /2 37/8 41/2 5 57/8 63/8 71/4 71/8 91/4 105/8 13 151/4 173/4 201/4 221/2 243/4 27 32
1

Diam. of Bolt Holes

3/4 78 7/8 7/8 7/8 7/8 7/8 7/8 3/4

No. of Bolts
4 4 4 8 8 8 8 8 8 12 12 16 16 20 20 24 24 24

Size of Bolts
/8 /8 3 /4 5 /8 3 /4 3 /4 3 /4 3 /4 3 /4 3 /4 7 /8 1 11/8 11/8 11/4 11/4 11/4 11/2
5 5

AA AA CROSS

EE FF

45

EE

1 11/8 3 1 /16 11/4 13/8 17/16 15/8 17/8 2 21/8 21/4 2 3/8 21/2 23/4

45 LATERAL

REDUCER

GG

ECCENTRIC REDUCER

GG

1 11/8 11/4 11/4 13/8 13/8 13/8 15/8

Nominal Pipe Size

1 11/4 11/2 2 21/2 3 31/2 4 5 6 8 10 12 14 16 18 20 24

AA
4 41/4 41/2 5 51/2 6 61/2 7 8 81/2 10 111/2 13 15 161/2 18 191/2 221/2

BB
5 51/2 6 61/2 7 73/4 81/2 9 101/4 111/2 14 161/2 19 211/2 24 261/2 29 34

CC
21/4 21/2 23/4 3 31/2 31/2 4 41/2 5 51/2 6 7 8 81/2 91/2 10 101/2 12

EE
61/2 71/4 81/2 9 101/2 11 121/2 131/2 15 171/2 201/2 24 271/2 31 343/4 371/2 401/2 471/2

FF
2 21/4 21/2 21/2 21/2 3 3 3 31/2 4 5 51/2 6 61/2 71/2 8 81/2 10

GG
41/2 41/2 41/2 5 51/2 6 61/2 7 8 9 11 12 14 16 18 19 20 24

Chart 7 300 Lb. Steel Pipe Flanges

* A raised face of 1/16 inch is included in (a) minimum thickness of flanges, and (b) "center to contact surface" dimension of fitting. Where facings other then 1/16 inch raised face are used, the "center to contact surface" dimensions shall remain unchanged.

Chart 9 300 Lb. Steel Flanged Fittings

TECH-F

1204

TECH-F-5 150 Lb. ANSI / Metric Flange Comparison

Flange Nom. I.D. Outside Diameter ANSI ISO JIS 150 10 lb. Bar 10 K Bolt Circle ANSI 150 lb. ISO 10 Bar Thickness (Min.) JIS ANSI ISO JIS 150 10 10 K lb. Bar 10 K Bolt Hole ANSI 150 lb. ISO 10 Bar JIS 10 K Bolts Quantity ANSI 150 lb. ISO 10 Bar JIS 10 K ANSI 150 lb. ISO 10 Bar Bolt Size JIS 10 K Raised Face Diameter ANSI ISO JIS 150 10 lb. Bar 10 K

1.00 4.25 4.53 1.50 5.00 5.91 2.00 6.00 6.50 2.50 7.00 7.28 3.00 7.50 7.87 3.50 8.50 0.00 4.00 9.00 8.66 100 229 220 90 216 0 80 191 200 65 178 185 50 52 165 40 127 150 25 108 115

4.92 3.12 5.51 3.88 6.10 4.75 6.89 5.50 7.28 6.00 7.68 7.00 8.27 7.50 210 191 195 178 185 152 175 140 155 121 140 98 125 79

3.35 3.54 0.56 0.63 4.33 4.13 0.69 0.71 4.92 4.72 0.75 0.79 5.71 5.51 0.88 0.79 6.30 5.91 0.94 0.79 0.00 6.30 0.94 0.00 7.09 6.89 0.94 0.87 9.45 9.45 1.00 0.94 240 240 25 24 180 175 24 22 0 160 24 0 160 150 24 20 145 140 22 20 125 120 19 20 110 105 17 18 85 90 14 16

0.55 0.63 0.63 0.71 0.71 0.71 0.71 0.87 0.87 0.94 0.94 1.02 1.10 1.18 1.18 1.26 1.42 1.50 1.57 1.73 44 40 38 36 32 30 30 28 26 24 24 22 22 18 18 18 18 16 16 14

0.62 0.55 0.75 0.62 0.71 0.75 0.75 0.71 0.75 0.75 0.71 0.75 0.75 0.71 0.75 0.75 0.00 0.75 0.75 0.71 0.75 0.88 0.87 0.91 0.88 0.87 0.91 1.00 0.87 0.98 1.00 0.87 0.98 1.12 0.87 0.98 1.12 1.02 1.06 1.25 1.02 1.06 1.25 1.02 1.06 1.38 1.16 1.30 1.38 0.00 1.30 1.62 1.28 1.30 1.62 1.40 1.54 1.62 1.54 1.54 41 39 39 41 35.5 39 41 32.5 33 35 0 33 35 29.5 33 32 26 27 32 26 27 28 26 27 28 22 25 25 22 25 25 22 25 22 22 23 22 22 23 19 18 19 19 0 19 19 18 19 19 18 19 19 18 19 16 18 19 16 14 19

4 4 4 4 4 8 8 8 8 12 12 12 16 16 20 20 28 32 36 44 -

4 4 4 8 8 -

4 4 4 4 8 8 8 8 12 12 16 16 16 20 20 24 24 28 28 32 -

0.5 0.5 0.62 0.62 0.62 0.62 0.62 0.75 0.75 0.88 0.88 1.00 1.00 1.12 1.12 1.25 1.25 1.50 1.50 1.50 -

M12 M16 M16 M16 M16 M16 M16 M16 M16 M16 M16 -

2.00 2.68 2.64 2.88 3.46 3.19 3.62 4.02 3.78 4.12 4.80 4.57 5.00 5.24 4.96 5.50 0.00 5.35 6.19 6.22 5.94 8.50 8.35 8.35 10.62 10.55 10.31 12.75 12.60 12.76 15.00 14.57 14.49 16.25 16.93 16.26 18.50 18.98 18.70 21.00 20.94 20.87 23.00 23.03 23.03 27.25 26.97 27.17 33.75 0.00 33.66 40.25 39.57 39.57 47.00 43.70 43.70 857 0 855 692 685.0 690 584 585 585 533 532 530 470 482 475 413 430 413 381 370 368 324 320 324 270 268 262 216 212 212 157 158 151 140 0 136 127 133 126 105 122 116 92 102 96 73 88 81 51 68 67

6.00 11.00 11.22 11.02 9.50 150 279 285 280 241

8 8 8 12 12 16 16 20 20 20 0 28 28 32 -

M16 M16 M20 M20 M20 M20 M20 M22 M20 M22 M20 M22 M24 M24 M24 M24 M24 M24 M27 M30 M30 -

8.00 13.50 13.39 12.99 11.75 11.61 11.42 1.12 0.94 10.00 16.00 15.55 15.75 14.25 13.78 13.98 1.19 1.02 12.00 19.00 17.52 17.52 17.00 15.75 15.75 1.25 1.10 14.00 21.00 19.88 19.29 18.75 18.11 17.52 1.38 1.18 16.00 23.50 22.24 22.05 21.25 20.28 20.08 1.44 1.26 18.00 25.00 24.21 24.41 22.75 22.24 22.24 1.56 1.38 20.00 27.50 26.38 26.57 25.00 24.41 24.41 1.69 1.50 24.00 32.00 30.71 31.30 29.50 28.54 28.74 1.88 1.65 30.00 38.75 0.00 38.19 36.00 0.00 35.43 2.12 0.00 36.00 46.00 43.90 44.09 42.75 41.34 41.34 2.38 1.34 42.00 53.00 48.43 48.62 49.50 45.67 45.67 2.62 1.34 48.00 59.50 57.28 57.68 56.00 54.33 54.33 2.75 1.50 1200 1230 1455 1465 1422 1380 1380 70 38 1000 1230 1230 1235 1257 1160 1160 67 34 900 1168 1115 1120 1086 1050 1050 60 34 750 984 0 970 914 0 900 54 0 600 813 780 795 749 725 730 48 42 500 699 670 675 635 620 620 43 38 450 635 615 620 578 565 565 40 35 400 597 565 560 540 515 510 37 32 350 533 505 490 476 460 445 35 30 300 483 445 445 432 400 400 32 28 250 406 395 400 362 350 355 30 26 200 343 340 330 298 295 290 28 24

M30 M30 1022 1005.0 1005 M33 M36 1194 1110.0 1110 M36 M36 1359 1330 1325 -

53.50 52.36 52.17

1205

TECH-F

TECH-F-6 300 Lb. ANSI / Metric Flange Comparison

Flange Nom. I.D. Outside Diameter ANSI ISO JIS 300 16 lb. Bar 16 K Bolt Circle ANSI 300 lb. ISO 16 Bar Thickness (Min.) JIS ANSI ISO JIS 300 16 16 K lb. Bar 16 K Bolt Hole ANSI 300 lb. ISO 16 Bar JIS 16 K Bolts Quantity ANSI 300 lb. ISO 16 Bar JIS 16 K ANSI 300 lb. Bolt Size ISO 16 Bar JIS 16 K Raised Face Diameter ANSI ISO JIS 300 16 lb. Bar 16 K

1.00 4.88 4.53 4.92 3.50 3.35 3.54 0.69 0.63 1.50 6.12 5.91 5.51 4.50 4.33 4.13 0.81 0.71 2.00 6.50 6.50 6.10 5.00 4.92 4.72 0.88 0.79 2.50 7.50 7.28 6.89 5.88 5.71 5.51 1.00 0.79 3.00 8.25 7.87 7.87 6.62 6.30 6.30 1.12 0.79 3.50 9.00 0.00 8.27 7.25 0.00 6.69 1.19 0.00 4.00 10.00 8.66 8.86 7.88 7.09 7.28 1.25 0.87 6.00 12.50 11.22 12.01 10.62 9.54 10.24 1.44 0.94 8.00 15.00 13.39 13.78 13.00 11.61 12.01 1.62 1.02 10.00 17.50 15.94 16.93 15.25 13.98 14.96 1.88 1.10 12.00 20.50 18.11 18.90 17.75 16.14 16.93 2.00 1.26 14.00 23.00 20.47 21.26 20.25 18.50 18.90 2.12 1.38 16.00 25.50 22.83 23.82 22.50 20.67 21.26 2.25 1.50 18.00 28.00 25.20 26.57 24.75 23.03 23.82 2.38 1.65 20.00 30.50 28.15 28.74 27.00 25.59 25.98 2.50 1.81 24.00 36.00 33.07 33.27 32.00 30.31 30.31 2.75 2.05 30.00 43.00 0.00 40.16 39.25 0.00 36.81 3.00 0.00 36.00 50.00 44.29 46.65 46.00 41.34 42.91 3.38 2.99 42.00 57.00 49.41 51.97 52.75 46.06 47.64 3.69 3.31 48.00 65.00 58.46 60.24 60.75 54.72 55.91 4.00 3.86 1200 1651 1485 1530 1543 1390 1420 102 98 1000 1448 1255 1320 1340 1170 1210 94 84 900 1270 1125 1185 1168 1050 1090 86 76 750 1092 0 1020 997 0 935 76 0 600 914 840 845 813 770 770 70 52 500 775 715 730 686 650 660 64 46 450 711 640 675 629 585 605 60 42 400 648 580 605 572 525 540 57 38 350 584 520 540 514 470 480 54 35 300 521 460 480 451 410 430 51 32 250 445 405 430 387 355 380 48 28 200 381 340 350 330 295 305 41 26 150 381 285 305 270 240 260 37 24 100 254 220 225 200 180 185 32 22 90 229 210 184 170 30 80 210 200 200 169 160 160 29 20 65 191 185 175 149 145 140 25 20 50 165 165 155 127.0 125 120 22 20 40 156 150 140 114 110 105 21 18 25 124 115 125 90 85 90 17 16

0.55 0.63 0.63 0.71 0.79 0.79 0.87 0.94 1.02 1.10 1.18 1.34 1.50 1.57 1.65 1.81 2.05 2.28 2.44 2.76 70 62 58 52 46 42 40 38 34 30 28 26 24 22 20 20 18 16 16 14

0.75 0.55 0.75 0.88 0.71 0.75 0.75 0.71 0.75 0.88 0.71 0.75 0.88 0.71 0.91 0.88 0.00 0.91 0.88 0.71 0.91 0.88 0.87 0.98 1.00 0.87 0.98 1.12 1.02 1.06 1.25 1.02 1.06 1.25 1.02 1.30 1.38 1.16 1.30 1.38 1.16 1.30 1.38 1.28 1.30 1.62 1.40 1.54 1.88 0.00 1.65 2.12 1.54 1.89 2.12 1.65 2.20 2.12 1.89 2.20 54 48 56 54 42 56 54 39 48 48 0 42 41 35.5 39 35 32.5 33 35 29.5 33 35 29.5 33 32 26 33 32 26 27 28 26 27 25 22 25 22 22 25 22 18 23 22 23 22 18 23 22 18 19 19 18 19 22 18 19 19 14 19

4 4 8 8 8 8 8 12 12 16 16 20 20 24 24 24 28 32 36 40 -

4 4 4 8 8 -

4 4 8 8 8 8 8 12 12 12 16 16 16 20 20 24 24 28 28 32 -

0.62 0.75 0.62 0.75 0.75 0.75 0.75 0.75 0.88 1.00 1.12 1.12 1.25 1.25 1.25 1.50 1.75 2.00 2.00 2.00 -

M12 M16 M16 M16 M16 M16 -

2.00 2.68 2.88 3.46 3.62 4.02 4.12 4.80 122 92 102 73 88 51 68

2.64 3.19 3.78 4.57 5.20 5.71 6.30 9.06 230 160 145 132 116 96 81 67

M16 M16 105 M16 M20 127 M20 140 -

5.00 5.24 133 0

5.50 0.00

8 8 12 12 12 16 16 20 20 20 0 28 28 32 -

M16 M20 157 -

6.19 6.22 8.50 8.35 212 158

M20 M22 216 M20 M22 270 M24 M24 324 M24 M24 381 M24 M30 413 M27 M30 470 M27 M30 533 M30 M30 584 -

10.62 10.55 10.83 268 275

12.75 12.60 13.58 320 345

15.00 14.57 15.55 370 395

16.25 16.93 17.32 430 440

18.50 18.98 19.49 482 495

21.00 20.94 22.05 532 560

23.00 23.03 24.21 27.25 26.97 28.35 33.75 0.00 34.65 40.25 39.57 40.55 0 880 585 615

M33 M36 692 685.0 720 0 M39 857 -

M36 M45 1022 1005.0 1030 -

M39 M52 1194 1110.0 1140 -

47.00 43.70 44.88 58.44 52.36 53.15

M45 M52 1484 1330 1350

TECH-F

1206

TECH-F-7 Weights and Dimensions of Steel & Wrought Iron Pipe Recommended for Use as Permanent Well Casings
Steel Pipe, Black or Galvanized Size In. Diameter - In. External Internal Thickness In.

Reprinted from American Water Works Association Standard A100-66 by permission of the Association. Copyrighted 1966 by the American Water Works Association, Inc., 2 Park Avenue, New Yok, NY 10016. Weight Per Foot - Lb 1 Plain Ends With Threads (Calculated) and Couplings (Nominal)2

6 8 8 8 10 10 10 12 12 14 14 16 16 18 18 20 20 22 22 22 24 24 24 26 26 28 28 30 30 32 32 34 34 36 36
1Manufacturing 2 Nominal

#Thickness indicated is believed to be best practice. If soil and water conditions are unusually favorable, lighter pipe may be used if permitted in the purchaser's specifications. larger sizes. weights of pipe with threads and couplings (based on lengths of 20 ft. including coupling) are shown for purposes of specification. Thread data are contained in the various standards covering sizes which can be purchased with threads. Wrought-Iron Pipe, Black or Galvanized Size In. Diameter - In. External Internal Thickness In.

6.625 8.625 8.625 8.625 10.750 10.750 10.750 12.750 12.750 14.000 14.000 16.000 16.000 18.000 18.000 20.000 20.000 22.000 22.000 22.000 24.000 24.000 24.000 26.000 26.000 28.000 28.000 30.000 30.000 32.000 32.000 34.000 34.000 36.000 36.000

6.065 8.249 8.071 7.981 10.192 10.136 10.020 12.090 12.000 13.500 13.250 15.376 15.250 17.376 17.250 19.376 19.250 21.376 21.250 21.000 23.376 23.250 23.000 25.376 25.000 27.376 27.000 29.376 29.000 31.376 31.000 33.376 33.000 35.376 35.000

0.280 0.188 0.277 0.322 0.279 0.307 0.365# 0.330 0.375# 0.250 0.375# 0.312 0.375# 0.312 0.375# 0.312 0.375# 0.312 0.375 0.500 0.312 0.375 0.500# 0.312 0.500# 0.312 0.500# 0.312 0.500# 0.312 0.500# 0.312 0.500# 0.312 0.500#

18.97 16.90 24.70 28.55 31.20 34.24 40.48 43.77 49.56 36.71 54.57 52.36 62.58 59.03 70.59 65.71 78.60 72.38 86.61 114.81 79.06 94.62 125.49 85.73 136.17 92.41 146.85 99.08 157.53 105.76 168.21 112.43 178.89 119.11 189.57

19.18 17.80 25.55 29.35 32.75 35.75 41.85 45.45 51.15 57.00 65.30 73.00 81.00

weight tolerance is 10 percent over and 3.5 percent under nominal weight for pipe 6-20 in. in size and +/- percent of nominal weight for

1Manufacturing 2Based

weight tolerance is 10 percent over and 3.5 percent under nominal weight for pipe ~20 in. in size and +10 percent of nominal weight for larger sizes. on length of 20 ft. including coupling. Threaded pipe has 8 threads per inch.

6 8 10 12 14 16 18 20 20 22 22 24 24 26 26 28 28 30 30

6.625 8.625 10.750 12.750 14.000 16.000 18.000 20.000 20.000 22.000 22.000 24.000 24.000 26.000 26.000 28.000 28.000 30.000 30.000

6.053 7.967 10.005 11.985 13.234 15.324 17.165 19.125 19.000 21.125 21.000 23.125 23.000 25.125 25.000 27.125 27.000 29.125 29.000

0.286 0.329 0.372 0.383 0.383 0.383 0.417 0.438 0.500* 0.438 0.500* 0.438 0.500* 0.438 0.500* 0.438 0.500* 0.438 0.500*

Weight Per Foot - Lb 1 Plain Ends With Threads (Calculated) and Couplings (Nominal)2

18.97 28.55 40.48 49.56 54.56 62.58 76.84 89.63 102.10 98.77 112.57 107.96 123.04 117.12 133.51 126.27 143.99 135.42 154.46

19.45 29.35 41.85 51.15 57.00 65.30 81.20 94.38 106.62

NOTE: Welded joints advocated for pipe larger than 20 in. in diameter; also for smaller diameter pipe, where applicable, to obtain clearance and maintain uniform grout thickness.

*Thickness indicated is believed to be best practice. If soil and water conditions are unusually favorable tighter pipe may be used if permitted in the purchaser's specifications.

1207

TECH-F

TECH-F-8 Capacities of Tanks of Various Dimensions

Diam. 1' 1' 1 1' 2" 1' 3" 1' 4" 1' 5" 1' 6" 1' 7" 1' 8" 1' 9" 1' 10" 1' 11" 2' 2' 1" 2' 2" 2' 3" 2' 4" 2' 5" 2' 6" 2' 7" 2' 8" 2' 9" 2' 10" 2' 11" 3' 3' 1" 3' 2" 3' 3" 3' 4" 3' 5" 3' 6" 3' 7" 3' 8" 3' 9" 3' 10" 3' 11" 4' 4' 1" 5.87 6.89 8.00 9.18 10.44 11.79 13.22 14.73 16.32 17.99 19.75 21.58 23.50 25.50 27.58 29.74 31.99 34.31 36.72 39.21 41.78 44.43 47.16 49.98 52.88 55.86 58.92 62.06 65.28 68.58 71.97 75.44 78.99 82.62 86.33 90.13 94.00 97.96 Gals. Area Sq. Ft. .785 .922 1.069 1.277 1.396 1.576 1.767 1.969 2.182 2.405 2.640 2.885 3.142 3.409 3.687 3.976 4.276 4.587 4.909 5.241 5.585 5.940 6.305 6.681 7.069 7.467 7.876 8.296 8.727 9.168 9.621 10.085 10.559 11.045 11.541 12.048 12.566 13.095 Diam. 4' 2 4' 3" 4' 4" 4' 5" 4' 6" 4' 7" 4' 8" 4' 9" 4' 10" 4' 11" 5' 5' 1" 5' 2" 5' 3" 5' 4" 5' 5" 5' 6" 5' 7" 5' 8" 5' 9" 5' 10" 5' 11" 6" 6' 3" 6' 6" 6' 9" 7' 7' 3" 7' 6" 7' 9" 8' 8' 3" 8' 6" 8' 9" 9" 9' 3" 9' 6" 9' 9" 102.00 106.12 110.32 114.61 118.97 123.42 127.95 132.56 137.25 142.02 146.91 151.81 156.83 161.94 167.11 172.38 177.71 183.14 188.66 194.25 199.92 205.67 211.51 229.50 248.23 267.69 287.88 308.81 330.48 352.88 376.01 399.80 424.48 449.82 475.89 502.70 530.24 558.51 Gals. Area Sq. Ft. 13.635 14.186 14.748 15.321 15.90 16.50 17.10 17.72 18.35 18.99 19.64 20.30 20.97 21.65 22.34 23.04 23.76 24.48 25.22 25.97 26.73 27.49 28.27 30.68 35.18 35.78 38.48 41.28 44.18 47.17 50.27 53.46 56.75 60.13 63.62 67.20 70.88 74.66 Diam. 10' 10' 3" 10' 6" 10' 9" 11' 11' 3" 11' 6" 11' 9" 12' 12' 3" 12' 6" 12' 9" 13' 13' 3" 13' 6" 13' 9" 14' 14' 3" 14 6" 14' 9" 15' 15' 3" 15' 6" 15' 9" 16' 16' 3" 16' 6" 16' 9" 19' 19' 3" 19' 6" 19' 9" 20' 20' 3" 20' 6" 20' 9" 21' 21' 3" 587.52 617.26 640.74 678.95 710.90 743.58 776.99 811.14 846.03 881.65 918.00 955.09 992.91 1031.50 1070.80 1110.80 1151.50 1193.00 1235.30 1278.20 1321.90 1366.40 1411.50 1457.40 1504.10 1551.40 1599.50 1648.40 2120.90 2177.10 2234.00 2291.70 2350.10 2409.20 2469.10 2529.60 2591.00 2653.00 Gals. Area Sq. Ft. 78.54 82.52 86.59 90.76 95.03 99.40 103.87 108.43 113.10 117.86 122.72 127.68 132.73 137.89 142.14 148.49 153.94 159.48 165.13 170.87 176.71 182.65 188.69 194.83 201.06 207.39 213.82 220.35 283.53 291.04 298.65 306.35 314.16 322.06 330.06 338.16 346.36 346.36 21' 6 21' 9" 22' 22' 3' 22' 6' 22' 9" 23' 23' 3" 23' 6" 23' 9" 24' 24' 3" 24' 6" 24' 9" 25' 25' 3" 25' 6" 25' 9" 26' 26' 3" 26' 6" 26' 9" 27' 27' 3" 27' 6" 27' 9" 28' 28' 3" 28' 6" 28' 9" 29' 29' 3" 29' 6" 29' 9" 30' 30' 3" 30' 6" 30' 9" Diam. 2715.80 2779.30 2843.60 2908.60 2974.30 3040.80 3108.00 3175.90 3244.60 3314.00 3384.10 3455.00 3526.60 3598.90 3672.00 3745.80 3820.30 3895.60 3971.60 4048.40 4125. 90 4204.10 4283.00 4362.70 4443.10 4524.30 4606.20 4688.80 4772.10 4856.20 4941.00 5026.60 5112.90 5199.90 5287.70 5376.20 5465.40 5555.40 Gals. Area Sq. Ft. 363.05 371.54 380.13 388.82 397.61 406.49 415.48 424.56 433.74 443.01 452.39 461.86 471.44 481.11 490.87 500.74 510.71 527.77 530.93 541.19 551.55 562.00 572.66 583.21 593.96 604.81 615.75 626.80 637.94 649.18 660.52 671.96 683.49 695.13 706.86 718.69 730.62 742.64

To find the capacity of tanks greater than shown above, find a tank of one-half the size desired, and multiply its capacity by four, or find one one-third the size desired and multiply its capacity by 9. Chart 10 Capacity of Round Tanks (per foot of depth)

Dimensions in Feet 4 5 6 7 8 9 10 11 12 X X X X X X X X X 4 5 6 7 8 9 10 11 12

To find the capacity of a depth not given, multiply the capacity for one foot by the required depth in feet. Chart 11 Capacity of Square Tanks

119.68 187.00 269.28 366.52 478.72 605.88 748.08 905.08 1077.12

1'

479. 748. 1077. 1466. 1915. 2424. 2992. 3620. 4308.

4'

598. 935. 1346. 1833. 2394. 3029. 3740. 4525. 5386

Contents in Gallons for Depth in Feet of: 5' 6' 8' 10' 718. 1202. 1616. 2199. 2872. 3635. 4488. 5430. 6463. 957. 1516. 2154. 2922. 3830. 4847. 5984. 7241. 8617.

1197. 1870 2693. 3665. 4787. 6059. 7480. 9051. 10771

1316. 2057. 2968 4032. 5266. 6665. 8228. 9956. 11848.

11'

1436. 2244 3231. 4398 5745. 7272. 8976. 10861. 12925.

12'

TECH-F

1208

Capacities of Tanks of Various Dimensions

Diameter 1 ft. 2 ft 3 ft. 4 ft. 5 ft. 6 ft. 7 ft 8 ft. 9 ft. 10 ft. 11 ft. 12 ft. 13 ft. 14 ft. 15 ft. .3 1.2 2.7 4.9 7.6 11.0 15.0 19.0 25.0 30.0 37.0 44.0 51.0 60.0 68.0 1/10 .8 3.3 7.5 13.4 20.0 30.0 41.0 52.0 67.0 83.0 101.0 120.0 141.0 164.0 188.0 1/5 1.4 5.9 13.6 23.8 37.0 53.0 73.0 96.0 112.0 149.0 179.0 214.0 250.0 291.0 334.0 Gallons Per Foot of Length When Tank is Filled 3/10 2/5 1/2 3/5 7/10 2.1 8.8 19.8 35.0 55.0 78.0 107.0 140.0 178.0 219.0 265.0 315.0 370.0 430.0 494.0 2.9 11.7 26.4 47.0 73.0 106.0 144.0 188.0 238.0 294.0 356.0 423.0 496.0 576.0 661.0 3.6 14.7 33.0 59.0 92.0 133.0 181.0 235.0 298.0 368.0 445.0 530.0 621.0 722.0 829.0 4.3 17.5 39.4 70.2 110.0 158.0 215.0 281.0 352.0 440.0 531.0 632.0 740.0 862.0 988.0 4.9 20.6 45.2 80.5 126.0 182.0 247.0 322.0 408.0 504.0 610.0 741.0 850.0 989.0 1134.0 4/5 5.5 22.2 50.1 89.0 139.0 201.0 272.0 356.0 450.0 556.0 672.0 800.0 940.0 1084.0 1253.0 9/10

Chart 12 Cylindrical Tanks Set Horizontally and Partially Filled Diam. In. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 32 34 36 Length of Cylinder 11' 12' 13' 14' 0.48 1.92 4.40 7.84 12.2 17.6 24.0 31.2 39.6 48.8 59.2 70.4 83.2 96.0 110. 125. 142. 158. 177. 196. 216. 238. 259. 282. 306. 331. 356. 384. 412. 440. 502. 566. 634. 0.52 2.08 4.76 8.50 13.3 19.1 26.0 33.8 43.0 52.8 64.2 76.2 90.2 104. 120. 135. 153. 172. 192. 212. 238. 257. 281. 306. 332. 359. 386. 416. 446. 476. 544. 614. 688. Diam. In. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 32 34 36

1" 0.01 0.03 0.05 0.08 0.12 0.17 0.22 0.28 0.34 0.41 0.49 0.57 0.67 0.77 0.87 0.98 1.10 1.23 1.36 1.50 1.65 1.80 1.96 2.12 2.30 2.48 2.67 2.86 3.06 3.48 3.93 4.41

0.04 0.16 0.37 0.65 1.02 1.47 2.00 2.61 3.31 4.08 4.94 5.88 6.90 8.00 9.18 10.4 11.8 13.2 14.7 16.3 18.0 19.8 21.6 23.5 25.5 27.6 29.7 32.0 34.3 36.7 41.8 47.2 52.9

1'

0.20 0.80 1.84 3.26 5.10 7.34 10.0 13.0 16.5 20.4 24.6 29.4 34.6 40.0 46.0 52.0 59.0 66.0 73.6 81.6 90.0 99.0 108. 118. 128. 138. 148. 160 171. 183 209 236. 264.

5'

0.24 0.96 2.20 3.92 6.12 8.80 12.0 15.6 19.8 24.4 29.6 35.2 41.6 48.0 55.2 62.4 70.8 79.2 88.4 98.0 108 119. 130. 141. 153. 166. 178. 192. 206. 220. 251. 283. 317.

6'

0.28 1.12 2.56 4.58 7.14 10.3 14.0 18.2 23.1 28.4 34.6 41.0 48.6 56.0 64.4 72.8 81.6 92.4 103. 114. 126 139. 151. 165. 179. 193. 208. 224. 240. 257. 293. 330. 370.

7'

0.32 1.28 2.92 5.24 8.16 11.8 16.0 20.8 26.4 32.6 39.4 46.8 55.2 64.0 73.6 83.2 94.4 106. 118. 130 144. 158. 173. 188. 204 221. 238. 256. 274. 294. 334. 378. 422.

8'

0.36 1.44 3.30 5.88 9.18 13.2 18.0 23.4 29.8 36.8 44.4 52.8 62.2 72.0 82.8 93.6 106. 119. 132. 147. 162. 178. 194. 212. 230. 248. 267. 288. 309. 330. 376. 424. 476.

9'

0.40 1.60 3.68 6.52 10.2 14.7 20.0 26.0 33.0 40.8 49.2 58.8 69.2 80.0 92.0 104. 118. 132. 147. 163. 180. 198. 216. 235. 255. 276. 297. 320. 343. 367. 418. 472. 528.

10'

0.44 1.76 4.04 7.18 11.2 16.1 22.0 28.6 36.4 44.8 54.2 64.6 76.2 88.0 101. 114 130. 145. 162. 180. 198. 218. 238. 259. 281. 304. 326. 352. 377. 404. 460. 520. 582.

0.56 2.24 5.12 9.16 14.3 20.6 28.0 36.4 46.2 56.8 69.2 82.0 97.2 112. 129. 146. 163. 185. 206. 229 252. 277. 302. 330. 358. 386. 416. 448. 480. 514. 586. 660. 740.

0.60 2.40 5.48 9.82 15.3 22.0 30.0 39.0 49.6 61.0 74.0 87.8 104. 120. 138. 156. 177. 198. 221. 245. 270. 297. 324. 353. 383. 414. 426. 480. 514. 550. 628. 708. 792.

15

0.64 2.56 5.84 10.5 16.3 23.6 32.0 41.6 52.8 65.2 78.8 93.6 110. 128. 147. 166. 189. 211. 235. 261. 288. 317. 346. 376. 408. 442. 476. 512. 548. 588. 668. 756. 844.

16'

0.68 2.72 6.22 11.1 17.3 25.0 34.0 44.2 56.2 69.4 83.8 99.6 117. 136. 156. 177. 201. 224. 250. 277. 306. 337. 367. 400. 434. 470. 504. 544. 584. 624. 710. 802. 898.

17'

0.72 0.80 2.88 3.20 6.60 7.36 11.8 13.0 18.4 20.4 26.4 29.4 36.0 40.0 46.8 52.0 60.0 66.0 73.6 81.6 88.8 98.4 106 118. 124. 138. 144. 160. 166. 184. 187. 208. 212. 236. 240. 264. 265. 294. 294. 326. 324. 360. 356. 396. 389. 432. 424 470. 460. 510. 496. 552. 534. 594. 576. 640. 618. 686. 660. 734. 752. 836. 848. 944. 952. 1056.

18'

20'

0.88 3.52 8.08 14.4 22.4 32.2 44.0 57.2 72.4 89.6 104. 129. 152. 176. 202. 229. 260. 290. 324. 359. 396. 436. 476. 518. 562. 608. 652. 704. 754. 808. 920. 1040. 1164.

22'

0.96 3.84 8.80 15.7 24.4 35.2 48.0 62.4 79.2 97.6 118. 1411 166. 192. 220. 250. 283. 317. 354. 392. 432. 476. 518. 564. 612. 662. 712. 768. 824. 880. 1004. 1132. 1268.

24'

Chart 13 Capacities, in U.S. Gallons of Cylinders of Various Diameters and Lengths

1209

TECH-F

TECH-G-1 Motor Enclosures

Section TECH-G Motor Data

Totally Enclosed, Fan-Cooled - An enclosed motor equipped for external cooling by means of a fan integral with the motor, but external to the enclosed parts. TEFC motors are designed for use in extremely wet, dirty, or dusty areas. Explosion-Proof, Dust-Ignition-Proof - An enclosed motor whose enclosure is designed to withstand an explosion of a specified dust, gas, or vapor which may occur within the motor and to prevent the ignition of this dust, gas, or vapor surrounding the motor. A motor manufacturer should be consulted regarding the various classes and groups of explosion-proof motors available and the application of each. Motor insulation is classified according to the total allowable temperature. This is made up of a maximum ambient temperature plus a maximum temperature rise plus allowances for hot spots and service factors. Class B insulation is the standard and allows for a total temperature of 130C. The maximum ambient is 40C, and the temperature rise is 70C, for ODP motors and 75C for TEFC motors.

The selection of a motor enclosure depends upon the ambient and surrounding conditions. The two general classifications of motor enclosures are open and totally enclosed. An open motor has ventilating openings which permit passage of external air over and around the motor windings. A totally enclosed motor is constructed to prevent the free exchange of air between the inside and outside of the frame, but not sufficiently enclosed to be termed air-tight. These two categories are further broken down by enclosure design, type of insulation, and/or cooling method. The most common of these types are listed below.

Open Drip Proof - An open motor in which all ventilating openings are so constructed that drops of liquid or solid particles falling on the motor at any angle from 0 to 15 degrees from vertical cannot enter the machine. This is the most common type and is designed for use in nonhazardous, relatively clean, industrial areas. Encapsulated - A dripproof motor with the stator windings completely surrounded by a protective coating. An encapsulated motor offers more resistance to moisture and/or corrosive environments than an ODP motor.

TECH-G-2 NEMA Frame Assignments

SINGLE-PHASE MOTORS Horizontal and Vertical open type
Design L, 60 cycles, class B insulation system, open type, 1.15 service factor. hp 3600 speed, rpm 1800 1200

POLYPHASE SQUIRREL-CAGE MOTORS Horizontal and Vertical open type fan cooled
Designs A and B - class B insulation system, open type 1.15 service factor, 60 cycles. hp
1

Designs A and B - class B insulation system totally-enclosed fan-cooled type, 1.00 service factor, 60-cycles. hp
1

1 11/2 2 3 5 71/2

3/4

143T 145T 182T 184T 213T

143T 145T 182T 184T 213T 215T

145T 182T 184T -

/2 3 /4 1 11/2 2 3 5 71/2 10 15 20 25 30 40 50 60 75 100 125 150 200 250

143T 145T 145T 182T 184T 213T 215T 254T 256T 284TS 286TS 324TS 326TS 364TS 365TS 404TS 405TS 444TS 445TS*

3600

143T 145T 145T 182T 184T 213T 215T 254T 256T 284T 286T 324T 326T 364TS 365TS 404TS 405TS 444TS 454TS -

speed, rpm 1800 1200

*The 250 hp rating at the 3600 rpm speed has a 1.0 service factor

143T 145T 182T 184T 213T 215T 254T 256T 284T 286T 324T 326T 364T 365T 404T 405T 444T 445T -

143T 145T 182T 184T 213T 215T 254T 256T 284T 286T 324T 326T 364T 365T 404T 405T 444T 445T -

900

/2 3 /4 1 1 1 /2 2 3 5 71/2 10 15 20 25 30 40 50 60 75 100 125 150

143T 145T 182T 184T 213T 215T 254T 256T 284TS 286TS 324TS 326TS 364TS 365TS 405TS 444TS 445TS

3600

143T 145T 145T 182T 184T 213T 215T 254T 256T 284T 286T 324T 326T 364TS 365TS 405TS 444TS 445TS

speed, rpm 1800 1200

143T 145T 182T 184T 213T 215T 254T 256T 284T 286T 324T 326T 364T 365T 404T 405T 444T 445T -

143T 145T 182T 184T 213T 215T 254T 256T 284T 286T 324T 326T 364T 365T 404T 405T 444T 445T -

900

TECH-G

1210

TECH-G-3 NEMA Frame Dimensions

IPP44 TOTALLY ENCLOSED & FLAMEPROOF (Similar to NEMA TEFC & Explosion Proof)
C M=N

O N-W F F AC U

D E E

H-SIZE HOLE

3 143T 1/2 /4 1 145T 3/4 1 11/2 - 2 1 182T 1 1 /2 3 184T 11/2 2 5 213T 2 3 71/2 215T 3 5 10 254T 5 71/2 15 256T 71/2 10 20 284T 10 15 25 284TS 286T 15 20 30 286TS 324T 20 25 40 324TS 326T 25 30 50 326TS 364T 30 40 364TS 60 365T 40 50 365TS 75 404T 50 60 404TS 100 405T 60 75 405TS 125 444T 75 100 444TS 150 445T 100 125 445TS 200 447T 447TS 56 1/2 3/4 182 1 3 184 /4 1-11/2 11/2-2 1 213 1-1 /2 2 3 215 2 3 5 254U 3 5 71/2 256U 5 71/2 10 284U 71/2 10 15 286U 10 20 324U 15 25 324S 326U 15 20 30 326S 364U 20 25 40 364US 365U 25 30 365US 50 404U 30 40 404US 60 405U 40 50 405US 75 444U 50 60 444US 100 445U 60 75 445US 125

Motor H.P. (Open) H.P. (Enclosed) A B C (Approx.) Frame 900 1200 1800 3600 900 1200 1800 3600 Max. Max. Open Encl.
3 11/2 1/2 /4 2-3 3/4 1 1 5 1 1 /2 71/2 11/2 2 10 2 3 15 3 5 20 5 7 1/2 25 71/2 10 10 15 30 15 20 40 20 25 50 25 30 60 30 40 75 40 50 100 50 60 125 60 75 150 75 100 200 100 125 250

D 31/2 33/4 41/2 41/2 51/4 51/4 61/4 61/4 7 7 7 7 8 8 8 8 9 9 9 9 10 10 10 10 11 11 11 11 11 11 31/2 41/2 41/2 51/4 51/4 61/4 61/4 7 7 8 8 8 8 9 9 9 9 10 10 10 10 11 11 11 11

E 23/4 23/4 33/4 33/4 41/4 41/4 5 5 51/2 51/2 51/2 51/2 61/4 61/4 61/4 61/4 7 7 7 7 8 8 8 8 9 9 9 9 9 9 27/16 33/4 33/4 41/4 41/4 5 5 51/2 51/2 6 1/4 61/4 61/4 61/4 7 7 7 7 8 8 8 8 9 9 9 9

F 2 23/4 21/4 23/4 23/4 33/4 41/8 5 43/4 43/4 51/2 51/2 51/4 51/4 6 6 55/8 55/8 61/8 61/8 61/8 61/8 67/8 67/8 71/4 71/4 81/4 81/4 10 10 11/2 21/4 23/4 23/4 31/2 41/8 5 43/4 51/2 51/4 51/4 6 6 55/8 55/8 61/8 61/8 61/8 61/8 67/8 67/8 71/4 71/4 81/4 81/4

H /32 /32 13 /32 13/32 13/32 13/32 17/32 17 /32 17/32 17/32 17/32 17/32 21/32 21/32 21 /32 21/32 21/32 21/32 21/32 21/32 13/16 13/16 13/16 13/16 13/16 13/16 13/16 13/16 13 /16 13/16 11/32 13/32 13/32 13/32 13/32 17/32 17 /32 17/32 17/32 21/32 21/32 21 /32 21/32 21/32 21/32 21/32 21/32 13/16 13/16 13/16 13/16 13/16 13/16 13/16 13/16
11 11

1 11/2- 2 3 5 71/2 10 15 20 25 30 40

11/2 2 3 5 71/2 10 15 20 25 30

50

40 50

75

60

75

60

125 150

100

125 150 11/2 2-3 5 71/2 10 15 20 25

100

3/4 11/2 1/2 1 2-3 3/4 1-11/2 11/2-2 1 5 1-1 /2 2 3 71/2 2 3 5 10 3 5 7 1/2 15 5 71/2 10 20 71/2 10 15 25 10 20 15 25 30 15 20 30 40 20 25 40 50 25 30 60 50 30 40 75 40 50 100 60 50 60 125 75 60 75 150 100

30 40 50 60

100

75

7 7 9 9 101/2 101/2 121/2 121/2 14 14 14 14 16 16 16 16 18 18 18 18 20 20 20 20 22 22 22 22 22 22 61/2 9 9 101/2 101/2 121/2 121/2 14 14 16 16 16 16 18 18 18 18 20 20 20 20 22 22 22 22

6 6 61/2 71/2 71/2 9 103/4 121/2 121/2 121/2 14 14 14 14 151/2 151/2 151/4 151/4 161/4 161/4 161/4 161/4 173/4 173/4 181/2 181/2 201/2 201/2 231/4 231/4 3 7/8 61/2 71/2 71/2 9 103/4 121/2 121/2 14 14 14 151/2 151/2 151/4 151/4 161/4 161/4 161/4 161/4 173/4 173/4 181/2 181/2 201/2 201/2

12 121/2 13 14 16 171/2 201/2 221/2 231/2 22 25 231/2 26 241/2 271/2 26 29 27 30 28 321/2 291/2 34 31 38 34 40 36 431/2 401/2 101/2 121/2 131/2 151/2 17 201/2 221/2 24 251/2 261/2 241/2 28 26 291/2 27 301/2 28 321/2 30 34 311/2 38 34 40 36

121/2 131/2 141/2 151/2 18 191/2 221/2 24 251/2 241/2 27 26 281/2 27 30 281/2 33 31 34 32 37 34 381/2 351/2 421/2 381/2 441/2 41 48 461/2

O (Approx.) Open Encl. 67/8 67/8 91/8 91/8 103/4 103/4 125/8 125/8 14 14 14 14 16 16 16 16 18 18 18 18 20 20 20 20 223/8 223/8 223/8 223/8 223/8 223/8 67/8 9 9 101/2 101/2 125/8 125/8 14 14 16 16 16 16 181/4 181/4 181/4 181/4 201/4 201/4 201/4 201/4 221/4 221/4 221/4 221/4 7 7 91/4 91/4 107/8 107/8 123/4 123/4 143/8 143/8 143/8 143/8 165/8 165/8 165/8 165/8 181/2 181/2 181/2 181/2 205/8 205/8 205/8 205/8 231/8 231/8 231/8 231/8 231/8 231/8

U /8 /8 1 1 /8 1 1 /8 13/8 13/8 15/8 15/8 17/8 15/8 17/8 15/8 21/8 17/8 21/8 17/8 23/8 17/8 23/8 17/8 27/8 21/8 27/8 21/8 33/8 23/8 33/8 23/8 33/8 23/8 5/8 7/8 7 /8 11/8 11/8 13/8 13/8 15/8 15/8 17/8 15/8 17/8 15/8 21/8 17/8 21/8 17/8 23/8 21/8 23/8 21/8 27/8 21/8 27/8 21/8
7 7

141/2 151/2 171/2 19 22 24 25 261/2 28 251/2 291/2 27 34 31 35 32 371/2 341/2 39 36 43 381/2 45 401/2

9 9 105/8 105/8 131/8 131/8 145/8 145/8 163/4 163/4 163/4 163/4 183/4 183/4 183/4 183/4 207/8 207/8 207/8 207/8 231/8 231/8 231/8 231/8

/16 x 3/32 /16 x 3/32 1 /4 x 1/8 1/4 x 1/8 5/16 x 5/32 5/16 x 5/32 3/8 x 3/16 3/8 X 3/16 1/2 x 1/4 3/8 x 3/16 1/2 x 1/4 3/8 x 3/16 1/2 x 1/4 1/2 x 1/4 1/2 x 1/4 1/2 x 1/4 5/8 x 5/16 1/2 x 1/4 5/8 x 5/16 1/2 x 1/4 3/4 x 3/8 1/2 x 1/4 3/4 x 3/8 1/2 x 1/4 7/8 x 7/16 5/8 x 5/16 7/8 x 7/16 5/8 x 5/16 7/8 x 7/16 5/8 x 5/16 3/16 x 3/32 3/16 x 3/32 3/16 X 3/32 1/2 x 1/8 1/2 x 1/8 5/16 x 5/32 5/16 x 5/32 3/8 x 3/16 3/8 X 3/16 1/2 x 1/4 3/8 X 3/16 1/2 x 1/4 3/8 X 3/16 1/2 x 1/4 1/2 x 1/4 1/2 x 1/4 1/2 x 1/4 5/8 X 5/16 1/2 x 1/4 5/8 X 5/16 1/2 x 1/4 3/4 X 3/8 1/2 x 1/4 3/4 X 3/8 1/2 x 1/4
3 3

V Keyway Min. AC 2 2 21/2 21/2 31/8 31/8 33/4 33/4 43/8 3 43/8 3 5 31/2 5 31/2 55/8 31/2 55/8 31/2 7 4 7 4 81/4 41/2 81/4 41/2 81/4 41/2 17/8 2 2 23/4 23/4 31/2 31/2 45/8 45/8 55/8 3 53/8 3 61/8 3/2 61/8 3/2 67/8 4 67/8 4 83/8 4 83/8 4

41/2 41/2 51/2 51/2 67/8 67/8 81/4 81/4 93/8 8 93/8 8 101/2 9 101/2 9 113/4 95/8 113/4 95/8 137/8 107/8 137/8 107/8 16 121/4 16 121/4 16 121/4 45/8 5 5 61/2 61/2 8 8 95/8 95/8 107/8 81/2 107/8 81/2 121/4 95/8 121/4 95/8 133/4 107/8 133/4 107/8 161/8 113/4 161/8 113/4

Bolts Wt. (Approx.) Dia. Lg. Open Encl. /4 /4 /16 5/16 5/16 5/16 3/8 3/8 3/8 3 /8 3/8 3 /8 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5 /8 5/8 1/4 5/16 5 /16 5/16 5/16 3 /8 3 /8 3/8 3/8 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8
1 5 1

1 1 1 1 11/4 11/4 11/2 11/2 11/2 11/2 13/4 13/4 13/4 13/4 13/4 13/4 13/4 13/4 21/4 21/4 21/4 21/4 21/4 21/4 21/4 21/4 21/4 21/4 1 1 60 70 1 70 80 1 105 125 1 115 140 11/4 180 210 11/4 210 245 11/2 280 330 11/2 325 365 13/4 380 480 13/4 380 480 13/4 430 560 13/4 430 560 13/4 525 720 13/4 670 710 13/4 580 785 13/4 730 780 21/4 725 965 21/4 860 1075 21/4 810 1110 2v 970 1165 21/4 985 1315 21/4 1175 1355 21/4 1135 1550 21/4 1340 1620

40 45 65 80 120 140 200 235 295 255 340 295 440 445 435 480 605 670 665 730 830 870 930 950 1165 1050 1370 1250 1800 1800

45 50 79 95 140 160 235 270 370 340 405 395 520 500 580 560 755 740 835 820 1050 1050 1160 1150 1440 1440 1650 1615 2260 2260

1211

TECH-G

TECH-G-4 Synchronous and Approximate Full Load Speed of Standard A.C. Induction Motors
NUMBER of POLES 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 60 CYCLE RPM SYNC. 3600 1800 1200 900 720 600 515 450 400 360 327 300 277 257 240 3500 1770 1170 870 690 575 490 430 380 340 310 285 265 245 230 F.L. 50 CYCLE RPM SYNC. 3000 1500 1000 750 600 500 429 375 333 300 273 240 231 214 200 2900 1450 960 720 575 480 410 360 319 285 260 230 222 205 192 F.L.

TECH-G-5 Full Load Amperes at Motor Terminals* Average Values for All Speeds and Frequencies
MOTOR HP
1/2 3/4

SINGLE-PHASE A-C 115 VOLTS 230 VOLTS**

** For full-load currents of 208 and 200 volt motors, increase the corresponding 230 volt motor full-load current by 10 and 15 percent respectively.

* These values for full-load current are for running at speeds usual for belted motors and motors with normal torque characteristics. Motors built for especially low speeds or high torques may require more running current, in which case the nameplate current rating should be used.

1 11/2 2 3 5 71/2 10 15 20 25 30 40 50 60 75 100 125 150 200 250

9.8 13.8 16 20 24 34 56 80 100

4.9 6.9 8 10 12 17 28 40 50

THREE PHASE A-C INDUCTION TYPE SQUIRREL CAGE & WOUND ROTOR 230 460 575 VOLTS** VOLTS VOLTS

DIRECT CURRENT 120 VOLTS 240 VOLTS

2.0 2.8 3.6 5.2 6.8 9.6 15.2 22 28 42 54 68 80 104 130 154 192 240 296 350 456 558

1.0 1.4 1.8 2.6 3.4 4.8 7.6 11 14 21 27 34 40 52 65 77 96 120 148 175 228 279

.8 1.1 1.4 2.1 2.7 3.9 6.1 9 11 17 22 27 32 41 52 62 77 96 118 140 182 223

5.2 7.4 9.4 13.2 17 25 40 58 76 112 148 184 220 292 360 430 536

2.6 3.7 4.7 6.6 8.5 12.2 20 29 29 55 72 89 106 140 173 206 255 350 440 530 710

TECH-G

1212

TECH-G-6 Motor Terms

AMPERE: a unit of intensity of electric current being produced in a conductor by the applied voltage.

FREQUENCY: the number of complete cycles per second of alternating current, e.g., 60 Hertz. HORSEPOWER: the rate at which work is done. It is the result of the work done (stated in foot-pounds) divided by the time involved. INERTIA: the property of physical matter to remain at rest unless acted on by some external force. Inertia usually concerns the driven load.

SERVICE FACTOR: a safety factor in some motors which allows the motor, when necessary, to deliver greater than rated horsepower.

SYNCHRONOUS SPEED & SLIP: the speed of an a-c motor at which the motor would operate if the rotor turned at the exact speed of the rotating magnetic field. However, in a-c induction motors, the rotor actually turns slightly slower. This difference is defined as slip and is expressed in percent of synchronous speed. Most induction motors have a slip of 1-3%. TORQUE: that force which tends to produce torsion or rotation. In motors, it is considered to be the amount of force produced to turn the load, it is measured in lb.-ft.

MOTOR EFFICIENCY: a measure of how effectively the motor turns electrical energy into mechanical energy. Motor efficiency is never 100% and is normally in the neighborhood of 85%. POWER FACTOR: the ratio of the true power to the volt-amperes in an alternating current circuit or apparatus. At 1800 rpm, a motor develops 3 lb.- ft per hp. At 1200 rpm, a motor develops 4.5 lb-ft per hp. At 575 volts, a 3-phase motor draws 1 amp per hp.

VOLTAGE: a unit of electro-motive force. It is a force which, when applied to a conductor, will produce a current in the conductor.

APPROXIMATE RULES OF THUMB

At 460 volts, a 3-phase motor draws 1.25 amp per hp.

At 115 volts, a single- phase motor draws 10 amp per hp.

At 230 volts, a single- phase motor draws 5 amp per hp.

At 230 volts, a single- phase motor draws 2.5 amp per hp.

Hp= Torque x RPM 5250

Torque in lb-ft = HP x 5250 RPM

MECHANICAL FORMULAS

RPM = 120 x Frequency No. of poles

0.75 1.5 3 5.5 7.5 11 18.5 30 45 75 Required Value HP Output

kW

Full Load 74 79 82.5 84.5 85.5 87 88.5 90 91 92

Average Efficiencies and Power Factors of Electric Motors Efficiency % Power Factor
3

/4 Load 73 78.5 82 84.5 85.5 87 88.5 89.5 90.5 91.5

/2 Load 69 76 80.5 83.5 84.5 85.5 87 88 89 90

Full Load 0.72 0.83 0.85 0.87 0.87 0.88 0.89 0.89 0.89 0.90

/4 Load 0.65 0.78 0.80 0.82 0.83 0.84 0.85 0.86 0.86 0.87

/2 Load 0.53 0.69 0.73 0.75 0.76 0.77 0.79 0.80 0.80 0.81

Full Load Amps on 3ph 415V 2.0 3.2 6.0 10.5 14 20 33 52 77 126

Direct Current I x E x Eff 746

Single Phases I x E x Eff x PF 746

Two-Phase 4-Wire I x E x 2 x Eff x Pf 746

Three Phase I x E x 1.73 x Eff x PF 746

TECH-G-7 Electrical Conversion Formulae

Amperes when horsepower (input) is known Amperes when kva is known Kilowatts Kva Amperes when kilowatts is known TO FIND DIRECT CURRENT HP x 746 E x Efff kW x 1000 E IxE 1000

P.F.

Horespower (output)
I = Amperes E = Volts HP= Horsepower

I x E x Eff 746

Eff= Effiency (decimal) P.F = Power Factor

HP x 746 E x Eff x P.F. kW x 1000 E x P.F. kva x 1000 E I x E x P.F. 1000 IxE 1000 KW Kva I x E x Eff x P.F. 746

ALTERNATING CURRENT Single Phase Three Phase

Kva = Kilovolt- amperes kW = Kilowatts

HP x 746 1.73 x E x Eff x P.F. kW x 1000 1.73 x E x P.F. kvax 1000 1.73 x E 1.73 x I x E x P.F. 1000 1.73 x I x E 1000 KW Kva 1.73 x I x E x Eff x P.F. 746

1213

TECH-G

TECH-G-8 Vertical Motors

VHS VERTICAL HOLLOWSHAFT Pump shaft thru motor and coupled below motor with impeller adjustment made at top of motor.

VHS VERTICAL SOLID SHAFT Pump shaft coupled to shaft extension below motor. Impeller adjustment at coupling

NOTE: The following dimensions may vary upon vendor selection and design: XC, CD, AG, AF, BV, C.

DIMENSIONS Top Shaft Dia.

3

BX Bore 0.751 1.188 1.501 1.938 2.188

BZ Dia. BC 13/8 1 /4
3 1 1 3

SQ Key Size
3

BY Tap Size 10-32

1

1 /16 1 /16 2 /16

3 15

1 /2
1

/4

1.001

/8

1 1 3 1

/16 /4 /4 /8 /2

10-32

2 /8 2 /2 3 /4
1

1 1

/4 - 20

/4 - 20 /4 - 20 - 16

1/2

3/8

VERTICAL HOLLOWSHAFT NEMA dimensions for common top drive coupling sizes.

TECH-G

1214

NEMA SOLID SHAFT NEMA DIMENSIONS FOR COMMON SOLID SHAFT EXTENSION SIZES. DIMENSIONS Motor Shaft Dia. AH U 11/8 21/8 25/8 27/8 31/8
7

V 23/4 23/4 41/4 41/4 61/2 7 5

H
5/8

B
3/8

C
3/4 3/4 3/4 3/4 3/4

D
11/16 15/16

Nominal Pump Shaft Keyway Diameters

3/16 3/8 1/4

/8

23/4 23/4 41/2 41/2 5 7 7

15/8

25/8 25/8 31/2 43/4 5

3/8 3/8 3/8 3/4 1

/8

x 3/22 x 3/16 x 1/4 x 5/16 x 3/8 x 3/8 x 1/8

11/4 13/4

1/2 5/8

/2

11/2

23/8 25/8

21/4

1, 13/16, 11/2, 115/16 23/16, 211/16 23/16, 11/16, 215/16 23/16

7/8, 1, 13/16, 1 1/2

7/8,

7/8

3/4 3/4

HEADSHAFT COUPLINGS
WITH VERTICAL HOLLOWSHAFT MOTOR: Impeller adjustment made on adjusting nut above motor (under motor canopy and bolted to top drive coupling). 1. Sleeve type (lineshaft) coupling. 2. Rigid flanged coupling (Type AR).

3. No coupling-straight shaft (not recommended due to difficult Installation/disassembly of head and motor).

WITH VERTICAL SOLID SHAFT MOTOR:

Impeller adjustment made on adjusting plate of coupling without removal of motor canopy. (VSS motors also provide a lesser tolerance of shaft run-out which coincides with mechanical seal recommendations). 1. Adjustable coupling (Type A). 2. Adjustable spacer coupling (Type AS-recommended for applications with mechanical seals. The mechanical seal can be removed without disengaging motor).

1215

TECH-G

TECH-G-9 I.E.C. Motor Frames

IPP44 TOTALLY ENCLOSED & FLAMEPROOF (Similar to NEMA TEFC & Explosion Proof)
C M=N

O N-W F F AC U

D E E

H-SIZE HOLE

DIMENSIONS I.E.C. Frames Poles All Units mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches mm Inches A B C Max. Max. Approx. 157 61/8 180 7 180 7 205 8 240 91/2 266 101/2 266 101/2 318 121/2 318 121/2 356 14 356 14 400 153/4 457 18 457 18 508 20 508 20 570 221/2 570 221/2 570 221/2 570 221/2 635 25 635 25 635 25 635 25 130 51/8 130 51/8 155 61/8 180 7 185 71/4 185 71/4 225 83/4 267 101/2 311 121/4 300 113/4 340 133/8 368 141/2 370 141/2 395 151/2 426 163/4 426 163/4 470 181/2 470 181/2 520 201/2 520 201/2 520 201/2 520 201/2 570 221/2 570 221/2 245 10 300 10 320 121/2 380 15 380 15 440 171/2 480 19 580 23 620 241/2 650 251/2 685 27 760 30 810 32 835 33 925 361/2 925 361/2 1000 391/2 1000 391/2 1060 42 1060 42 1140 45 1140 45 1190 47 1190 47 D 80 3.15 90 3.54 90 3.54 100 3.94 112 4.41 132 5.20 132 5.20 160 6.30 160 6.30 180 7.09 180 7.09 200 7.87 225 8.86 225 8.86 250 9.84 250 9.84 280 11.02 280 11.02 280 11.02 280 11.02 315 12.41 315 12.41 315 12.41 315 12.41 E 63 21/2 70 23/4 70 23/4 80 31/8 95 33/4 108 41/4 108 41/4 127 5 127 5 140 51/2 140 51/2 159 61/4 178 7 178 7 203 8 203 8 229 9 229 9 229 9 229 9 254 10 254 10 254 10 254 10 F 50 2 50 2 63 211/2 70 23/4 70 23/4 70 23/4 89 31/2 105 41/8 127 5 121 43/4 140 51/2 153 6 143 55/8 156 61/8 175 67/8 175 67/8 184 71/4 184 71/4 210 81/4 210 81/4 203 8 203 8 229 9 229 9 H 10 3 /8 10 3 /8 10 3/8 12 15/32 12 15/32 12 15/32 12 15/32 15 19/32 15 19 /32 15 19/32 15 19/32 19 3 /4 19 3/4 19 3/4 24 15/16 24 15/16 24 15/16 24 15/16 24 15/16 24 15/16 28 13/32 28 13/32 28 13/32 28 13/32 M&N 140 51/2 156 6 3/16 169 611/16 193 75/8 200 77/8 239 93/8 258 101/8 323 123/4 345 135/8 352 137/8 371 145/8 396 151/2 402 157/8 445 171/2 483 19 483 19 514 201/4 514 201/4 540 211/4 540 211/4 559 22 589 231/4 585 23 615 241/4 O Approx. 185 71/4 210 81/4 210 81/4 230 9 250 10 290 111/2 290 111/2 360 14 360 14 400 153/4 400 153/4 440 171/2 490 191/4 490 191/4 550 215/8 550 215/8 630 243/4 630 243/4 630 243/4 630 243/4 725 281/2 725 281/2 725 281/2 725 281/2 U Nominal Tolerance j6 j6 N&W 40 11/2 50 2 50 2 60 23/8 60 23/8 80 31/8 80 31/8 110 43/8 110 43/8 110 43/8 110 43/8 110 43/8 110 43/8 140 51/2 140 51/2 140 51/2 140 51/2 140 51/2 140 51/2 140 51/2 140 51/2 170 611/16 140 51/2 170 611/16 AC 90 31/2 106 43/16 106 43/16 123 47/8 130 51/8 169 65/8 169 65/8 218 85/8 218 85/8 231 91/8 231 91/8 243 91/2 259 101/4 289 113/8 308 121/8 308 121/8 330 13 330 13 330 13 330 113 356 14 386 151/4 356 14 386 151/4 Weight Approx.

D80-19 E80-19 D90S24 E900S24 D90L24 E90L24 D100L28 E100L28 D112M28 E112M28 D132S38 E132S38 D132M38 E132M38 D160M42 E160M42 D160L42 E160L42 D180M48 E180M48 D180L48 E180L48 D200L55 E200L55 D225S55 E225S55 D225M60 E225M60 D250M60 E250M60 D250M65 E250M65 D280S65 E280S65 D280S75 E280S75 D280M65 E280M65 D280M75 E280M75 D315S65 E315S65 D315S80 E315S80 D315S80 E315M65 D315M80 E315M80

4 to 8 4 to 8 4 to 8 4 to 8 4 to 8 4 to 8 2 2 2 2 2

19 7890 24 9459 24 .9499 28 1.1024 28 1.1024 38 1.4961 38 1.4961 42 1.6539 42 1.6539 48 1.8898 48 1.8898 55 2.1654 55 2.1654 60 2.3622 60 2.3622 65 2.5591 65 2.5591 75 2.9528 65 2.5591 75 2.9528 65 2.5591 80 3.1945 65 2.5591 80 3.1495

j6 j6

k6 k6 k6

j6

k6 k6

k6

m6 m6 m6 m6 m6 m6 m6 m6 m6 m6 m6 m6 m6

10 kg 20 Lbs 20 kg. 45 kg. 22 kg. 50 Lbs. 30 kg. 65 Lbs. 44 kg. 100 Lbs 65 kg. 145 Lbs 90 kg. 100 Lbs. 120 kg. 265 Lbs. 150 kg. 330 Lbs 175 kg. 385 Lbs. 190 kg. 420 Lbs. 255 kg. 560 Lbs. 290 kg. 640 Lbs 350 kg 770 Lbs. 440 kg. 970 Lbs. 440 kg. 970 Lbs. 615 kg 1355 Lbs. 615 kg. 1355 Lbs. 675 kg. 1500 Lbs. 675 kg. 1500 Lbs. 800 kg. 1760 Lbs. 800 kg. 1760 Lbs 900 kg. 1985 Lbs. 900 kg. 1985 Lbs.

TECH-G

1216

I.E.C. Motor Frames (cont'd)

IP23 ENCLOSED VENTILATED (Similar to NEMA Open Drip Proof)
C M=N

O U N-W F F AC

H-SIZE HOLE

DIMENSIONS I.E.C. Frames C160M48 C180M55 C200M60 C225M60 C250S65 C250S75 C200L60 C180L55 C160L48 Poles All Units A B C Max. Max. Approx. 267 101/2 311 121/4 300 113/4 340 133/8 326 127/8 368 141/2 395 151/2 395 151/2 388 151/4 388 151/4 426 163/4 426 163/4 470 181/2 470 181/2 520 201/2 520 201/2 520 201/2 520 201/2 570 221/2 570 221/2 700 271/2 750 291/2 770 301/4 810 317/8 870 341/4 900 351/2 970 38 970 38 1100 431/4 1100 431/4 1140 447/8 1140 447/8 1265 493/4 1265 493/4 1315 513/4 1315 513/4 1475 58 1475 58 1525 60 1525 60 D 160 6.30 160 6.30 180 7.09 180 7.09 200 7.87 200 7.87 225 8.86 225 8.86 250 9.84 250 9.84 250 9.84 250 9.84 280 11.02 280 11.02 280 11.02 280 11.02 315 12.40 315 12.40 315 12.40 315 12.40 E 127 5 127 5 140 51/2 140 51/2 159 61/4 159 61/4 178 7 178 7 203 8 203 8 203 8 203 8 229 9 229 9 229 9 229 9 254 10 254 10 254 10 254 10 F 105 41/8 127 5 121 43/4 140 51/2 133 51/4 152 6 156 61/8 156 61/8 154 61/8 154 61/8 175 67/8 175 67/8 184 71/4 184 71/4 210 81/4 210 81/4 203 8 203 8 229 9 229 9 H
19/32 19

M&N 323 123/4 345 135/8 352 137/8 371 145/8 406 16 425 163/4 445 171/2 445 171/2 464 181/4 464 181/4 483 19 483 19 514 201/4 544 217/16 540 211/4 570 227/16 559 22 589 231/4 585 23 615 241/4

All

All

All

All 2

All

C225M65

4 to 8 4 to 8 4 to 8 4 to 8 4 to 8 4 to 8 4 to 8 2 2 2 2 2 2

C250M65 C280S65

C250M75 C280S80

C280M80 C315S70 C315S90

C280M65

C315M7C C315M90

mm 318 inches 121/2 mm 318 inches 121/2 mm 356 inches 14 mm 356 inches 14 mm 400 inches 153/4 mm 400 inches 153/4 mm 457 inches 18 mm 457 inches 18 mm 508 inches 20 mm 508 inches 20 mm 508 inches 20 mm 508 inches 20 mm 570 inches 221/2 mm 570 inches 221/2 mm 570 inches 22 1/2 mm 570 inches 221/2 mm 635 inches 25 mm 635 inches 25 mm 635 inches 25 mm 635 inches 25

15 /32 15 19/32 15 19/32 19 3/4 19 3 /4 19 3/4 19 3/4 24 15/16 24 15/16 24 15/16 24 15/16 24 15/16 24 15/16 24 15/16 24 15/16 28 13/32 28 13/32 28 13/32 28 13/32

15

O Approx. 330 13 330 13 370 141/2 370 141/2 410 16 410 16 490 191/4 490 191/4 550 215/8 550 215/6 550 215/8 550 215/8 630 243/4 630 243/4 630 243/4 630 243/4 725 281/2 725 281/2 725 281/2 725 281/2

48 1.8898 48 1.8898 55 2.1654 55 2.1654 60 2.3622 60 2.3622 60 2.3622 65 2.5591 65 2.5591 75 2.9528 65 2.5591 75 2.9528 65 2.5591 80 3.1496 65 2.5591 80 3.1496 70 2.7559 90 3.5433 70 2.7559 90 3.5433

U Nominal Tolerance k6

N&W 110 43/8 110 43/8 110 43/8 110 43/8 140 51/2 140 51/2 140 51/2 140 51/2 140 51/2 140 51/2 140 51/2 140 51/2 140 51/2 170 611/16 140 51/2 170 611/16 140 51/2 170 611/16 140 51/2 170 611/16

AC 218 85/8 218 85/8 231 91/8 231 91/8 273 103/4 273 103/4 289 113/8 289 113/8 308 121/8 308 121/8 308 121/8 308 121/8 330 13 360 143/16 330 13 360 143/16 356 14 386 151/4 356 14 386 151/4

m6

m6

k6

m6

m6

m6

m6 m6 m6 m6 m6

m6

m6 m6

m6

m6

m6

m6

m6

120 kg 265 Lbs. 150 kg 330 Lbs. 200 kg 440 Lbs. 210 kg 465 Lbs. 270 kg 595 Lbs. 285 kg 630 Lbs. 350 kg 770 Lbs. 350 kg 770 Lbs. 450 kg 990 Lbs. 450 kg 990 Lbs. 500 kg 1100 Lbs. 500 kg 1100 Lbs. 650 kg 1435 Lbs. 650 kg 1435 Lbs. 700 kg 1545 Lbs. 700 kg 1545 Lbs. 850 kg 1875 Lbs. 850 kg 1875 Lbs. 950 kg 2100 Lbs. 950 kg 2100 Lbs.

Weight Approx.

1217

TECH-G

TECH-G-10 TEFC IP55 Metric IEC Motors (Conversion NEMA to Metric)

1 1 1 1.5 1.5 1.5 2 2 2 3 3 3 4 4 4 5.5 5.5 5.5 7.5 7.5 7.5 10 10 10 15 15 15 20 20 20 25 25 25 30 30 30 40 40 40 50 50 50 60 60 60 75 75 75 100 100 100 125 125 125 150 150 150 HP .75 .75 .75 1.1 1.1 1.1 1.5 1.5 1.5 2.2 2.2 2.2 3.0 3.0 3.0 4.0 4.0 4.0 5.5 5.5 5.5 7.5 7.5 7.5 11 11 11 15 15 15 18.5 18.5 18.5 22 22 22 30 30 30 37 37 37 45 45 45 55 55 55 75 75 75 90 90 90 110 110 110 kW RPM 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 3000 1500 1000 FRAME 80 80 90S 80 90S 90L 90S 90L 100L 90L 100L 112M 100L 100L 132S 112M 112M 132M 132S 132S 132M 132S 132M 160M 160M 160M 160L 160M 160L 180L 160L 180M 200L 180M 180L 200L 200L 200L 225M 200L 225S 250S 225M 225M 250M 250S 250S 280S 250M 250M 280M 280S 280S 315S 280M 280M 315M NEMA Equivalent Frame 56 56 143T 56 143T 145T 143T 145T 182T 145T 182T 184T 182T 182T 213T 184T 184T 215T 213T 213T 215T 213T 215T 254T 254T 254T 256T 254T 256T 284T 256T 284T 326T 284T 286T 326T 326T 326T 365T 326T 364T 404T 354T 365T 405T 404T 404T 444T 405T 405T 445T 444T 444T 504Z 445T 445T 505Z

TECH-G

1218

TECH-H-1 Temperature Conversion Chart {Centigrade (Celsius)-Fahrenheit}

C -40 -38 -36 -34 -32 F -40.0 -36.4 -32.8 -29.2 -25.6 C +5 6 7 8 9 10 11 12 13 14 F +41.0 42.8 44.6 46.4 48.2 50.0 51.8 53.6 55.4 57.2 C +40 41 42 43 44 45 46 47 48 49 F +104.0 105.8 107.6 109.4 111.2 113.0 114.8 116.6 118.4 120.2 C +175 180 185 190 195 200 205 210 215 220 F +347 356 365 374 383 392 401 410 419 428 C +350 355 360 365 370 375 380 385 390 395 F +662 671 680 689 698 707 716 725 734 743 C +750 800 850 900 950 1000 1050 1100 1150 1200 F +1382 1472 1562 1652 1742 1832 1922 2012 2102 2192

Section TECH-H Conversion Factors

-10 -9 -8 -7 -6 -5 -4 -3 -2 -1

-15 -14 -13 -12 -11

-20 -19 -18 -17 -16

-30 -28 -26 -24 -22

-22.0 -18.4 -14.8 11.2 -7.6 -4.0 -2.2 -0.4 +1.4 3.2 5.0 6.8 8.6 10.4 12.2

0 +1 2 3 4

32.0 33.8 35.6 47.4 39.2

23.0 24.8 26.6 28.4 30.2

14.0 15.8 17.6 19.4 21.2

35 36 37 38 39

30 31 32 33 34

25 26 27 28 29

20 21 22 23 24

15 16 17 18 19

95.0 96.8 98.6 100.4 102.2

86.0 87.8 89.6 91.4 93.2

77.0 78.8 80.6 82.4 84.2

68.0 69.8 71.6 73.4 75.2

59.0 60.8 62.6 64.4 66.2

150 155 160 165 170

125 130 135 140 145

100 105 110 115 120

75 80 85 90 95

50 55 60 65 70

302.0 311.0 320.0 329.0 338.0

257.0 266.0 275.0 284.0 293.0

212.0 221.0 230.0 239.0 248.0

167.0 176.0 185.0 194.0 203.0

122.0 131.0 140.0 149.0 158.0

325 330 335 340 345

300 305 310 315 320

275 280 285 290 295

250 255 260 265 270

225 230 235 240 245

617 626 635 644 653

572 581 590 599 608

527 536 545 554 563

482 491 500 509 518

437 446 455 464 473

500 550 600 650 700

475 480 485 490 495

450 455 460 465 470

425 430 435 440 445

400 405 410 415 420

932 1022 1112 1202 1292

887 896 905 914 923

842 851 860 869 878

797 806 815 824 833

752 761 770 779 788

2250 2300 2350 2400 2450

2000 2050 2100 2150 2200

1750 1800 1850 1900 1950

1500 1550 1600 1650 1700

1250 1300 1350 1400 1450

4082 4172 4262 4352 4442

3632 3722 3812 3902 3992

3182 3272 3362 3452 3542

2732 2822 2912 3002 3092

2282 2372 2462 2552 2642

Degrees Celsius = (Degrees Fahrenheit - 32) x 5 9 Degrees Fahrenheit = (Degrees Celsius x 9) + 32 5

Degrees Kelvin (K) = Degrees Celsius + 273.15 (0 degrees K or R = absolute zero)

Degrees Rankine (R) = Degrees Fahrenheit + 459.69

1219

TECH-H

TECH-H-2 A.P.I. and Baum Gravity Tables and Weight Factors

A.P.I Gravity 0 1 2 3 4 5 10.247 9.223 8.198 7.173 6.148 5.124 Baum Gravity Specific Gravity 1.0760 1.0679 1.0599 1.0520 1.0443 1.0366 Lbs. Per U.S. Gal. 8.962 8.895 8.828 8.762 8.698 8.634 U.S. Gals. per Lb. 0.1116 0.1124 0.1133 0.1141 0.1150 0.1158 A.P.I Gravity 51 52 53 54 55 Baum Gravity 50.57 51.55 52.54 53.53 54.52 Specific Gravity 0.7753 0.7711 0.7669 0.7628 0.7587 Lbs. Per U.S. Gal. 6.455 6.420 6.385 6.350 6.316 U.S. Gals. per Lb. 0.1549 0.1558 0.1566 0.1575 0.1583

6 7 8 9 10

11 12 13 14 15

4.099 3.074 2.049 1.025 10.00

16 17 18 19 20

10.99 11.98 12.97 13.96 14.95

1.0291 1.0217 1.0143 1.0071 1.0000

21 22 23 24 25

15.94 16.93 17.92 18.90 19.89

0.9930 0.9861 0.9792 0.9725 9.9659

8.571 8.509 8.448 8.388 8.328

26 27 28 29 30

20.88 21.87 22.86 23.85 24.84

0.9593 0.9529 0.9465 0.9402 0.9340

8.270 8.212 8.155 8.099 8.044

0.1167 0.1175 0.1184 0.1192 0.1201

56 57 58 59 60

31 32 33 34 35

25.83 26.82 27.81 28.80 29.79

0.9279 0.9218 0.9159 0.9100 0.9024

7.989 7.935 7.882 7.830 7.778

0.1209 0.1218 0.1226 0.1235 0.1243

61 62 63 64 65

55.51 56.50 57.49 58.48 59.47

36 37 38 39 40

30.78 31.77 32.76 33.75 34.73

0.8984 0.8927 0.8871 0.8816 0.8762

7.727 7.676 7.627 7.578 7.529

0.1252 0.1260 0.1269 0.1277 0.1286

66 67 68 69 70

60.46 61.45 62.44 63.43 64.42

0.7547 0.7507 0.7467 0.7428 0.7389

41 42 43 44 45

35.72 36.71 37.70 38.69 39.68

0.8708 0.8654 0.8602 0.8850 0.8498

7.481 7.434 7.387 7.341 7.296

0.1294 0.1303 0.1311 0.1320 0.1328

71 72 73 74 75

65.41 66.40 67.39 68.37 69.36

0.7351 0.7313 0.7275 0.7238 0.7201

6.283 6.249 6.216 6.184 6.151

46 47 48 49 50

40.67 41.66 42.65 43.64 44.63

0.8448 0.8398 0.8348 0.8299 0.8251

7.251 7.206 7.163 7.119 7.076

0.1337 0.1345 0.1354 0.1362 0.1371

76 77 78 79 80

70.35 71.34 72.33 73.32 74.31

0.7165 0.7128 0.7093 0.7057 0.7022

6.119 6.087 6.056 6.025 5.994

0.1592 0.1600 0.1609 0.1617 0.1626

45.62 50.61 50.60 50.59 50.58

0.8203 0.8155 0.8109 0.8063 0.8017

7.034 6.993 6.951 6.910 6.870

0.1379 0.1388 0.1396 0.1405 0.1413

81 82 83 84 85

75.30 76.29 77.28 78.27 79.26

0.6988 0.6953 0.6919 0.6886 0.6852

5.964 5.934 5.904 5.874 5.845

0.1634 0.1643 0.1651 0.1660 0.1668

0.7972 0.7927 0.7883 0.7839 0.7796

6.830 6.790 6.752 6.713 6.675

0.1422 0.1430 0.1439 0.1447 0.1456

86 87 88 89 90

80.25 81.24 82.23 83.22 84.20

0.6819 0.6787 0.6754 0.6722 0.6690

5.817 5.788 5.759 5.731 5.703

0.1677 0.1685 0.1694 0.1702 0.1711

6.637 6.600 6.563 6.526 6.490

0.1464 0.1473 0.1481 0.1490 0.1498

0.1507 0.1515 0.1524 0.1532 0.1541

96 97 98 99 100

91 92 93 94 95

85.19 86.18 87.17 88.16 89.15

0.6659 0.6628 0.6597 0.6566 0.6536

5.676 5.649 5.622 5.595 5.568

0.1719 0.1728 0.1736 0.1745 0.1753

90.14 91.13 92.12 93.11 94.10

0.6506 0.6476 0.6446 0.6417 0.6388

5.542 5.516 5.491 5.465 5.440

0.1762 0.1770 0.1779 0.1787 0.1796

95.09 96.08 97.07 98.06 99.05

0.6360 0.6331 0.6303 0.6275 0.6247

5.415 5.390 5.365 5.341 5.316

0.1804 0.1813 0.1821 0.1830 0.1838

0.6220 0.6193 0.6166 0.6139 0.6112

5.293 5.269 5.246 5.222 5.199

0.1847 0.1855 0.1864 0.1872 0.1881

5.176 5.154 5.131 5.109 5.086

0.1889 0.1898 0.1906 0.1915 0.1924

0.1932 0.1940 0.1949 0.1957 0.1966

The relation of Degrees Baum or A.P.I. to Specific Gravity is expressed by the following formulas: For liquids lighter than water: Degrees Baum = 140 - 130, G For liquids heavier than water: G= 140 130 + Degrees Baum

The above tables are based on the weight of 1 gallon (U.S.) of oil with a volume of 231 cubic inches at 60 Fahrenheit in air at 760 m.m. pressure and 50% humidity. Assumed weight of 1 gallon of water at 60 Fahrenheit in air is 8.32828 pounds.

Degrees A.P.I. = 141.5 - 131.5, G

141.5 G= 131.5 + Degrees A.P.I. 145 145 - Degrees Baum

To determine the resulting gravity by missing oils of different gravities: D = Density or Specific Gravity of mixture m = Proportion of oil of d1 density n = Proportion of oil of d2 density d1 = Specific Gravity of m oil d2 = Specific Gravity of n oil D = md1 - nd2 m+n

Degrees Baum = 145 - 145 , G

G=

G = Specific Gravity = ratio of the weight of a given volume of oil at 60 Fahrenheit to the weight of the same volume of water at 60 Fahrenheit.

TECH-H

1220

TECH-H-3 Approximate Conversion Table for Hardness Numbers Obtained by Different Methods*
Brinell Number 10 mm. Ball 3000 Kg. Load 682 653 633 614 596 578 560 543 527 500 475 451 432 409 390 371 353 336 319 301 286 271 258 247 237 226 212 194 179 158 141 125 110 99 89 Rockwell Number C-Scale 61.7 60 59 58 57 56 55 54 53 52 50 48 46 44 42 40 38 36 34 32 30 28 26 24 22 20 16 12 8 2 B-Scale Shore Scieroscope Number 84 81 79 78 77 75 73 72 71 69 67 64 62 58 56 54 51 49 47 44 42 41 38 37 35 34 32 29 27 24 21 18 Vickers Pyramid Number 737 697 674 654 636 615 596 578 561 544 513 484 458 434 412 392 372 354 336 318 302 286 272 260 248 238 222 204 188 166 141 125 110 99 89

TECH-H-4 Conversion Factors

*Compiled from various manufacturers' tables.

99 98 95 92 89 83 77 70 62 55 47

English measures - unless otherwise designated, are those used in the United States, and the units of weight and mass are avoirdupois units. Gallon - designates the U.S. gallon. To convert into the Imperial gallon, multiply the U.S. gallon by 0.83267. Likewise, the word ton designates a short ton 2,000 pounds. Multiply By To Obtain

Properties of water - it freezes at 32F., and is at its maximum density at 39.2 F. In the multipliers using the properties of water, calculations are based on water at 39.2 F. in a vacuum, weighing 62.427 pounds per cubic foot, or 8.345 pounds per U.S. gallon.

Acres Acres Acres Acres Acre-feet Acre-feet Acre-feet Atmospheres Atmospheres Atmospheres Atmospheres

43,560 4047 1.562 x 10-3 4840 43,560 325,851 1233,48 1.0332 1.01325 76.0 29.92

Square feet Square meters Square miles Square yards Cubic feet Gallons Cubic Meters Atmospheres (metric) Bars Cms. of mercury Inches of mercury

Atmospheres Atmospheres Atmospheres Atmospheres Atmospheres (metric) Atmospheres (metric) Bars Bars Bars Bars Bars

Multiply

33.90 10,332 14.70 1.058 0.9678 980,665. .98692 33.456 29.530 1.0197 2088.6

By

Feet of water kgs/sq. ft Lbs./ sq. inch Tons/sq. ft. Atmospheres Bars Atmospheres Feet H2O @39F. In. Hg @ 32 F. kg/cm2 Pounds/ ft.2

To Obtain

1221

TECH-H

Bars Barrels- oil Barrels- beer Barrels- whiskey Barrels/day- oil Bags or sacks-cement Board feet British Thermal Units British Thermal Units British Thermal Units British Thermal Units British Thermal Units B.T.U./min. B.T.U./min. B.T.U./min. B.T.U./min. Centares (Centiares) Centigrams Centiliters Centimeters Centimeters Centimeters Centimeters of mercury Centimeters of mercury Centimeters of mercury Centimeters of mercury Centimeters of mercury Centimeters of mercury Centimeters of mercury Centimeters/sec. Centimeters/sec. Centimeters/sec. Centimeters/sec. Centimeters/sec. Centimeters/sec. Cms./sec./sec. Centipoises Centipoises Centistokes Centistokes Cubic centimeters Cubic centimeters Cubic centimeters Cubic centimeters Cubic centimeters Cubic centimeters Cubic centimeters Cubic centimeters Cubic cm/sec. Cubic cm/sec. Cubic feet Cubic feet Cubic feet Cubic feet Cubic feet Cubic feet Cubic feet Cubic feet Cubic feet Cubic feet/min.

Multiply

14.504 42 31 45 0.02917 94 144 sq. in. x 1 in. 0.2520 777.6 3.927 x 104 107.5 2.928 x 104 12.96 0.02356 0.01757 17.57 1 0.01 0.01 0.3937 0.01 10 0.01316 0.013332 0.013595 0.4461 136.0 27.85 0.1934 1.969 0.03281 0.036 0.6 0.02237 3.728 x 10-4 0.03281 0.001 0.01 0.01 0.01 3.531 x 10-5 6.102 x 10-2 10-6 1.308 x 10-6 2.642 x 10-4 9.999 x 10-4 2.113 x 10-3 1.057 x 10-3 0.0158502 0.001 0.1781 2.832 x 10-4 1728 0.02832 0.03704 7.48052 28.32 59.84 29.92 472.0

By

Pounds/in.2 Gallons- oil Gallons- beer Gallons- whiskey Gallons/min.- oil Pounds/cement Cubic inches Kilogram- calories Foot- lbs. Horsepower- hrs. Kilogram- meters Kilowatt- hrs. Foot-lbs./sec. Horsepower Kilowatts Watts Square meters Grams Liters Inches Meters Millimeters Atmosphere Bars kg/cm2 Feet of water kgs/sq. meter Lbs./sq. ft. Lbs./sq. inch Feet/min. Feet/sec. Kilometers/hr. Meters/min. Miles/hr. Miles/min. Feet/sec./sec. Pascal-second Poises Sq. cm/sec. Stokes Cubic feet Cubic inches Cubic meters Cubic yards Gallons Liters Pints (liq.) Quarts (liq.) Gallons/minute Liters/sec. Barrels (42 US Gal.) Cubic cms. Cubic inches Cubic meters Cubic yards Gallons Liters Pints (liq.) Quarts (liq.) Cubic cms./sec.

To Obtain

Cubic feet/min. Cubic feet/min. Cubic feet/min. Cubic feet/sec. Cubic feet/sec. Cubic inches Cubic inches Cubic inches Cubic inches Cubic inches Cubic inches Cubic inches Cubic inches Cubic meters Cubic meters Cubic meters Cubic meters Cubic meters Cubic meters Cubic meters Cubic meters Cubic meters/hr. Cubic yards Cubic yards Cubic yards Cubic yards Cubic yards Cubic yards Cubic yards Cubic yards Cubic yards Cubic yards/min. Cubic yards/min. Cubic yards/min. Cubic yards/min. Decigrams Deciliters Decimeters Degrees (angle) Degrees (angle) Degrees (angle) Degrees/sec. Degrees/sec. Degrees/sec. Dekagrams Dekaliters Dekameters Drams Drams Drams Fathoms Feet Feet Feet Feet Feet Feet Feet Feet of water Feet of water

Multiply

0.1247 0.4719 62.43 0.646317 448.831 16.39 5.787 x 10-4 1.639 x 10-5 2.143 x 10-5 4.329 x 10-3 1.639 x 10-2 0.03463 0.01732 106 35.31 61023 1.308 264.2 999.97 2113 1057 4.40 4.8089 764,554.86 27 46, 656 0.7646 202.0 764.5 1616 807.9 0.45 202.0 3.366 12.74 0.1 0.1 0.1 60 0.01745 3600 0.01745 0.1667 0.002778 10 10 10 27.34375 0.0625 1.771845 6 30.48 0.166667 3.0480 x 10-4 304.80 12 0.3048 1/3 0.0295 0.8826

By

Gallons/sec. Liters/sec. Pounds of water/min. Millions gals./day Gallons/min. Cubic centimeters Cubic feet Cubic meters Cubic yards Gallons Liters Pints (liq.) Quarts (liq.) Cubic centimeters Cubic feet Cubic inches Cubic yards Gallons Liters Pints (liq.) Quarts (liq.) Gallons/min. Barrels (42 U.S. Gal.) Cubic centimeters Cubic feet Cubic inches Cubic meters Gallons Liters Pints (liq.) Quarts (liq.) Cubic feet/sec. Gallons/min. Gallons/sec. Liters/sec. Grams Liters Meters Minutes Radians Seconds Radians/sec. Revolutions/min. Revolutions/sec. Grams Liters Meters Grains Ounces Grams Feet Centimeters Fathoms Kilometers Millimeters Inches Meters Yards Atmospheres Inches of mercury

To Obtain

TECH-H

1222

Feet of water Feet of water Feet of water Feet/min. Feet/min. Feet/min. Feet/min. Feet/min. Feet/sec. Feet/sec. Feet/sec. Feet/sec. Feet/sec. Feet/sec. Feet/sec./sec. Feet/sec./sec. Feet/sec./sec. Foot- pounds Foot- pounds Foot- pounds Foot- pounds Foot- pounds Foot- pounds/min. Foot- pounds/min. Foot- pounds/min. Foot- pounds/min. Foot- pounds/min. Foot- pounds/sec. Foot- pounds/sec. Foot- pounds/sec. Foot- pounds/sec. G's (Accel. due to grav.) G's (Accel. due to grav.) G's (Accel. due to grav.) G's (Accel. due to grav.) Gallons Gallons Gallons Gallons Gallons Gallons Gallons Gallons Gallons-Imperial Gallons- US Gallons water Gallons per day Gallons per day Gallons per day Gallons per day Gallons per hour Gallons per hour Gallons per hour Gallons per hour Gallons per hour Gallons per hour Gallons per hour Gallons/min.

Multiply

304.8 62.43 0.4335 0.5080 0.01667 0.01829 0.3048 0.01136 30.48 1.09726 0.5924 18.29 0.6818 0.01136 30.48 0.3048 0.0310810 1.286 x 10-3 5.050 x 10-7 3.240 x 10-4 0.1383 3.766 x 10-7 2.140 x 10-5 0.01667 3.030 x 10-5 5.393 x 10-3 2.280 x 10-5 7.704 x 10-2 1.818 x 10-3 1.941 x 10-2 1.356 x 10-3 32.174 35.3034 9.80665 21.9371 3785 0.1337 231 3.785 x 10-3 4.951 x 10-3 3.785 8 4 1.20095 0.83267 8.345 9.284 x 10-5 1.5472 x 10-6 2.6289 x 10-6 0.09284 0.1337 0.002228 3.71 x 10-5 6.309 x 10-5 .016667 2.7778 x 10-4 0.06309 34.286

By

kgs./sq. meter Lbs./sq. ft. Lbs./sq. inch Centimeters/sec. Feet/sec. Kilometers/hr. Meters/min. Miles/hr. Centimeters/sec. Kilometers/hr. Knots Meters/min. Miles/hr. Miles/min. Cms./sec./sec. Meters/sec./sec. g's (gravity) British Thermal Units Horsepower-hrs. Kilogram- calories Kilogram- meters Kilowatt- hours B.T.U/sec. Foot-pounds/sec. Horsepower Gm.-calories/sec. Kilowatts B.T.U/min. Horsepower kg.-calories/min. Kilowatts Feet/sec.2 Km/hr.-sec. Meters/sec.2 Miles/hr.-sec. Cubic centimeters Cubic feet Cubic inches Cubic meters Cubic yards Liters Pints (liq.) Quarts (liq.) US Gallons Imperial Gallons Pounds of water Cubic ft./min. Cubic ft./sec. Cubic meters/min. Liters/min. Cubic ft./hr. Cubic ft./min. Cubic ft./sec. Cubic meters/min. Gallons/min. Gallons/sec. Liters/min. Barrels (42 US Gal.)/day

To Obtain

Gallons/min. Gallons/min. Gallons/min. Gallons/min. Gallons/min. Gallons/min. Gallons/sec. Gallons/sec. Grains (troy) Grains (troy) Grains (troy) Grains/US gal. Grains/US gal. Grains/Imp. gal. Grams Grams Grams Grams Grams Grams Grams Grams/cm. Grams/cu. cm. Grams/cu. cm. Grams/liter Grams/liter Grams/liter Grams/liter Hectares Hectares Hectograms Hectoliters Hectometers Hectowatts Horsepower Horsepower Horsepower Horsepower Horsepower Horsepower Horsepower Horsepower (boiler) Horsepower (boiler) Horsepower (boiler) Horsepower (boiler) Horsepower-hours Horsepower-hours Horsepower-hours Horsepower-hours Horsepower-hours Inches Inches Inches Inches Inches Inches of mercury Inches of mercury Inches of mercury

Multiply

1.4286 0.02381 1440 2.228 x 10-3 0.06308 8.0208 60 227.12 0.06480 0.04167 2.0833 x 10-3 17.118 142.86 14.254 980.7 15.43 .001 1000 0.03527 0.03215 2.205 x 10-3 5.600 x 10-3 62.43 0.03613 58.416 8.345 0.06242 1000 2.471 1.076 x 105 100 100 100 100 42.44 33,000 550 1.014 10.547 0.7457 745.7 33, 493 9.809 9.2994 9809.5 2546 1.98 x 106 641.6 2.737 x 105 0.7457 2.540 0.083333 0.0254 25.4 0.0277778 0.03342 0.03386 13.6

By

Barrels (42 US Gal.)/hr. Barrels (42 USGal.)/min. Gallons/day Cubic feet/sec. Liters/sec. Cu. ft./hr. Gallons/min. Liters/min. Grams Pennyweights (troy) Ounces Parts/million Lbs./million gal. Parts/million Dynes Grains Kilograms Milligrams Ounces Ounces (troy) Pounds Pounds/ inch Pounds/cubic foot Pounds/cubic inch Grains/gal. Pounds/1000 gals. Pounds/cubic foot Parts/million Acres Square feet Grams Liters Meters Watts B.T.U./min. Foot-lbs./min. Foot-lbs./sec. Horsepower (metric) kg.-calories/min. Kilowatts Watts B.T.U./hr. Kilowatts B.T.U./sec. Watts B.T.U Foot-lbs. Kilogram-calories Kilogram-meters Kilowatt-hours Centimeters Feet Meters Millimeters Yards Atmospheres Bars Inches H2O

To Obtain

1223

TECH-H

Inches of mercury Inches of mercury Inches of mercury Inches of mercury Inches of mercury Inches of mercury Inches of mercury Inches of mercury (32 F) Inches of water Inches of water Inches of water nches of water Inches of water Inches of water Joules Joules Joules Joules Joules Joules Joules Kilograms Kilograms Kilograms Kilograms Kilograms Kilograms Kilograms Kilograms Kilograms Kilograms-cal./sec. Kilograms-cal./sec Kilograms-cal./sec Kilograms-cal./sec Kilograms/cm Kilograms/cm Kilograms/cm Kilograms/cm Kilograms-cal./min. Kilograms-cal./min Kilograms-cal./min kgs/meter kgs/sq. meter kgs/sq. meter kgs/sq. meter kgs/sq. meter kgs/sq. meter kgs/sq. millimeter Kiloliters Kilometers Kilometers Kilometers Kilometers Kilometers Kilopascal Kilometers/hr. Kilometers/hr. Kilometers/hr. Kilometers/hr. Kilometers/hr.

Multiply

0.034531 3374.1 70.727 0.49116 1.133 345.3 70.73 0.491 0.002458 0.07355 25.40 0.578 5.202 0.03613 9.479 x 10-4 0.239006 0.73756 3.725 x 10-7 2.7778 x 10-7 1 2.7778 x 10-4 35.274 32.151 980,665 2.205 1.102 x 10-3 34.286 9.8421 x 10-4 0.001 103 3.968 3086 5.6145 4186.7 0.96783 0.980665 28.959 14.223 3085.9 0.09351 69.733 0.6720 9.678 x 10-5 3.281 x 10-3 2.896 x 10-3 0.2048 1.422 x 10-3 106 103 105 3281 103 0.6214 1094 .145 27.78 54.68 0.9113 .5399 16.67

By

kg/cm2 Pascals Pounds/ft.2 Pounds/in.2 Feet of water kgs./sq. meter Lbs./sq. ft. Lbs./sq. inch Atmospheres Inches of mercury kgs./sq. meter Ounces/sq. inch Lbs./sq. foot Lbs./sq. inch B.T.U Calories (Thermo) Foot-lb.f. HP-hr. (US) Kilowatt-hr. Newton-m Watt-hr. Ounces (avoir) Ounces (troy) Dynes Lbs. Tons (short) Tons (assay) Tons (long) Tons (metric) Grams B.T.U./sec. Foot-lbs./sec. Horsepower Watts Atmospheres Bars Inches Hg@ 32 F Pounds/in.2 Foot-lbs./min. Horsepower Watts Lbs./foot Atmospheres Feet of water Inches of mercury Lbs./sq. foot Lbs./sq. inch kgs./sq. meter Liters Centimeters Feet Meters Miles Yards Pounds/in.2 Centimeters/sec. Feet/min. Feet/sec. Knots Meters/min.

To Obtain

Kilometers/hr. Kms./hr./sec. Kms./hr./sec. Kms./hr./sec. Kilowatts Kilowatts Kilowatts Kilowatts Kilowatts Kilowatts Kilowatts Kilowatts Kilowatts Kilowatts Kilowatt-hours Kilowatt-hours Kilowatt-hours Kilowatt-hours Kilowatt-hours Liters Liters Liters Liters Liters Liters Liters Liters Liters/min. Liters/min. Lumber width (in) x Thickness (in) 12 Meters Meters Meters Meters Meters Meters Meters/min. Meters/min. Meters/min. Meters/min. Meters/min. Meters/sec. Meters/sec. Meters/sec. Meters/sec. Meters/sec. Meters/sec. Meters/sec.2 Meters/sec.2 Meters/sec.2 Meters/sec.2 Meter-kg. (force) Microns Miles Miles Miles Miles Miles/hr.

Multiply

0.6214 27.78 0.9113 0.2778 56.907 4.425 x 104 737.6 1.341 1.3597 1000 3412.9 0.94827 14.34 103 3414.4 2.655 x 106 1.341 860.4 3.671 x 105 103 0.03531 61.02 10-3 1.308 x 10-3 0.2642 2.113 1.057 5.886 x 10-4 4.403 x 10-3 Length (ft.) 100 3.281 39.37 10-3 103 1.094 1.667 3.281 0.05468 0.06 0.03728 196.8 3.281 3.6 0.06 2.287 0.03728 3.2808 0.101972 39.37 134.214 9.8067 10-6 1.609 x 105 5280 1.609 1760 44.70

By

Miles/hr. Cms./sec./sec. Ft./sec./sec. Meters/sec./sec. B.T.U./min. Foot-lbs./min. Foot-lbs./sec. Horsepower (US) Horsepower (metric) Joules/sec. B.T.U/hr. B.T.U./sec. kg.-calories/min. Watts B.T.U Foot-lbs. Horsepower-hrs. Kilogram-calories Kilogram-meters Cubic centimeters Cubic feet Cubic inches Cubic meters Cubic yards Gallons Pints (liq.) Quarts (liq.) Cubic ft./sec. Gals./sec. Board feet Centimeters Feet Inches Kilometers Millimeters Yards Centimeters/sec. Feet/min. Feet/sec. Kilometers/hr. Miles/hr. Feet/min. Feet/sec. Kilometers/hr. Kilometers/min. Miles/hr. Miles/min. Feet/sec.2 G (gravity) Inches/sec.2 Miles/hr.-min. Joules Meters Centimeters Feet Kilometers Yards Centimeters/sec.

To Obtain

TECH-H

1224

Miles/hr. Miles/hr. Miles/hr. Miles/hr. Miles/hr. Miles/min. Miles/min. Miles/min. Miles/min. Milliers Milligrams Milliliters Millimeters Millimeters Milligrams/liter Million Gals./day Miner's inches Minutes (angle) Newtons (N) Ounces Ounces Ounces Ounces Ounces Ounces Ounces Ounces (troy) Ounces (troy) Ounces (troy) Ounces (troy) Ounces (troy) Ounces (fluid) Ounces (fluid) Ounces/sq. inch Ounces/gal (US) Ounces/gal (US) Ounces/gal (US) Ounces/gal (US) Parts/million Parts/million Parts/million Pennyweights (troy) Pennyweights (troy) Pennyweights (troy) Pennyweights (troy) Pounds Pounds Pounds Pounds Pounds Pounds Pounds Pounds (troy) Pounds (troy) Pounds (troy) Pounds (troy) Pounds (troy) Pounds (troy) Pounds (troy) Pounds (troy)

Multiply

88 1.467 1.609 0.8689 26.82 2682 88 1.609 60 103 10-3 10-3 0.1 0.03937 1 1.54723 1.5 2.909 x 10-4 .225 16 437.5 0.0625 28.3495 0.9115 2.790 x 10-5 2.835 x 10-5 480 20 0.08333 31.10348 1.09714 1.805 0.02957 0.0625 7.4892 0.25 0.46753 2.7056 x 10-4 0.0584 0.07015 8.345 24 1.55517 0.05 4.1667 x 10-3 16 256 7000 0.0005 453.5924 1.21528 14.5833 5760 240 12 373.2417 0.822857 13.1657 3.6735 x 10-4 4.1143 x 10-4

By

Feet/min. Feet/sec. Kilometers/hr. Knots Meter/min. Meters/min. Feet/sec. Kilometers/min. Miles/hr. Kilograms Grams Liters Centimeters Inches Parts/million Cubic ft./sec. Cubic ft./min. Radians Pounds-force Drams Grains Pounds Grams Ounces (troy) Tons (long) Tons (metric) Grains Pennyweights (troy) Pounds (troy) Grams Ounces (avoir) Cubic inches Liters Lbs./sq. inch kg/m3 Ounces/quart Pounds/ft.3 Pounds/in.3 Grains/US gal. Grains/Imp. gal. Lbs./million gal. Grains Grams Ounces (troy) Pounds (troy) Ounces Drams Grains Tons (short) Grams Pounds (troy) Ounces (troy) Grains Pennyweights (troy) Ounces (troy) Grams Pounds (avoir.) Ounces (avoir.) Tons (long) Tons (short)

To Obtain

Pounds (troy) Pounds of water Pounds of water Pounds of water Pounds of water/min. Pounds/cubic foot Pounds/cubic foot Pounds/cubic foot Pounds/cubic inch Pounds/cubic inch Pounds/cubic inch Pounds/foot Pounds/inch Pounds/sq. in. Pounds/sq. in. Pounds/sq. in. Pounds/sq. in. Pounds/sq. in. Pounds/sq. foot Pounds/sq. foot Pounds/sq. foot Pounds/sq. inch Pounds/sq. inch Pounds/sq. inch Pounds/sq. inch Pounds/sq. foot Pounds/sq. foot Pounds/sq. foot Pounds/sq. foot Pounds/sq. foot Pounds/sq. foot Quadrants (angle) Quadrants (angle) Quadrants (angle) Quarts (dry) Quarts (liq.) Quintal, Argentine Quintal, Brazil Quintal, Castile, Peru Quintal, Chile Quintal, Mexico Quintal, Metric Quires Radians Radians Radians Radians/sec. Radians/sec. Radians/sec. Radians/sec./sec. Radians/sec./sec. Reams Revolutions Revolutions Revolutions Revolutions/min. Revolutions/min. Revolutions/min. Revolutions/min./min. Revolutions/min./min.

Multiply

3.7324 x 10-4 0.01602 27.68 0.1198 2.670 x 10-4 0.01602 16.02 5.787 x 10-4 27.68 2.768 x 10-4 1728 1.488 1152 0.06895 5.1715 0.070307 6895 6895 0.01602 4.882 6.944 x 10-3 0.06804 2.307 2.036 703.1 4.788 x 10-4 0.035913 0.014139 4.8824 x 10-4 47.880 47.880 90 5400 1.571 67.20 57.75 101.28 129.54 101.43 101.41 101.47 220.46 25 57.30 3438 0.637 57.30 0.1592 9.549 573.0 0.1592 500 360 4 6.283 6 0.1047 0.01667 1.745 x 10-3 2.778 x 10-4

By

Tons (metric) Cubic feet Cubic inches Gallons Cubic ft./sec Grams/cubic cm. kgs./cubic centimeters Lbs./cubic inch Grams/cubic inch kgs./cubic meter Lbs./cubic foot kgs/meter Grams/cm. Bars Cm Hg @ 0 C kg./cm2 Newtons/m2 Pascals Feet of water kgs./sq. meter Pounds/sq. inch Atmospheres Feet of water Inches of mercury kgs./sq. meter Bars Cm Hg @ 0C In Hg @ 32C kg/cm2 Newtons/m2 Pascals Degrees Minutes Radians Cubic inches Cubic inches Pounds Pounds Pounds Pounds Pounds Pounds Sheets Degrees Minutes Quadrants Degrees/sec. Revolutions/sec. Revolutions/min. Revs./min./min. Revs./sec./sec. Sheets Degrees Quadrants Radians Degrees/sec. Radians/sec. Revolutions/sec. Rads./sec./sec. Rev./sec./sec.

To Obtain

1225

TECH-H

Revolutions/ sec Revolutions/ sec Revolutions/ sec Revolutions/sec/sec Revolutions/ sec/sec. Seconds (angle) Square centimeters Square centimetera Square centimeters Square centimeters Square feet Square feet Square feet Square feet Square feet Square feet 1 Sq. ft./ gal. Min Square inches Square inches Square inches Square kilometers Square kilometers Square kilometers Square kilometers Square kilometers Square meters Square meters Square meters Square meters Square miles Square miles Square miles Square miles Square millimeters Square milimeters Square yards Square yards

Multiply

360 6.283 60 6,283 3600 4.848 X 10-6 1.076 X10-3 0.1550 104 100 2.296 X 10-5 929.0 144 0.09290 3.587 X10-4 1/9 8.0208 6.542 6.944 X 10-3 645.2 247.1 10.76 X 106 106 0.3861 1.196 X 106 2.471 X10-4 10.76 3.861 X 10-7 1.196 640 27.88 x 106 2.590 3.098 x 106 0.01 1.550 x 10-3 2.066x 10-4 9

By

Degrees/ sec. Radians/ sec. Revolutions/ min. Radians/sec./sec Revs. / min/ min Radians Square feet Square inches Square meters Square milimeters Acres Square centimeters Square inches Square meters Square miles Square yards Overflow rate (ft. / hr.) Square centimeters Square feet Square millimeters Acres Square feet Square meters Square miles Square yards Acres Square feet Square miles Square yards Acres Square feet Square kilometers Square yards Square centimeters Square inchea Acres Square feet

To Obtain

Square yards Square yards Temp. (C.) + 273 Temp. ( C.) +17.78 Temp. ( F.) + 460 Temp ( F.) -32 Tons (long) Tons (long) Tons (long) Tons (metric) Tons (metric) Tons (short) Tons (short) Tons (short) Tons (short) Tons (short) Tons (short) Tons (short) Tons of water/ 24 hrs. Tons of water/24 hrs Tons of water/ 24 hrs Watts Watts Watts Watts Watts Watts Watts Watts Watt- hours Watt- hours Watt- hours Watt- hours Watt- hours Watt- hours Yards Yards Yards Yards

Multiply

0.8361 3.228 X 10-7 1 1.8 1 5/9 1016 2240 1.12000 103 2205 2000 32,000 907. 1843 2430.56 2430.56 29166.66 0.90718 83.333 0.16643 1.3349 0.05686 44.25 0.7376 1.341 X 10-3 0.001360 1 0.01434 10-3 3.414 2655 1.341 X 10-3 0.8604 367.1 10-3 91.44 3 36 0.9144

By

Square Meters Square miles Abs. Temp. ( C.) Temp. ( F.) Abs. Temp ( F.) Temp. ( C.) Kilogams Pounds Tons (short) Kilogams Pounds Pounds Ounces Kilograms Pounds (troy) Tons (long) Ounces (troy) Tons (metric) Pounds water/ hr. Gallons/ min. Cu. Ft. / hr. B.T..U/ min Foot- Lbs. / min. Foot- Lb/sec. Horsepower (U .S) Horsepower( metric) Joules/ sec Kg- calories/ min. Kilowatts B.T.U Foot- Lbs Horsepower- hrs Kilogram-calories kilogram- meters Kilowatt- hours Centimeters Feet Inches Meters

To Obtain

TECH-H

1226

TECH-H-5 Quick Convert Tables

inch2 x 645.16- mm2 inch2 x 6.4516 = cm2 in- lbf x 0.113 = N m ft- lbf x 1.356 = N m BENDING MOMENT (Torque) AREA mm2 x .00155= inch2 cm2 x 0.1550 = inch2 N m x 8.85 = in-lbs cm2 = square centimeter mm2 = square millimeter N m= Newton- meter

gpm x 0.2271 = m3/h gpm x 0.638 = liters per second FORCE lbf x 0.00448 = kN foot x 0.3048 = m LENGTH HEAD ( & NPSH)

CAPACITY (Volume per Unit Time)

m3/h x 4.403 = gpm liters/ second x 15.85 = gpm

m3/h= cubic meter per hour

kN = kilonewton m x 3.28084 = foot mm x 0.003281 = feet mm 0.03937= inch m x 3.281 = foot m = meter mm= millimeter m = meter

foot x 304.8 = mm inch x 25.4 = mm foot x 0.3048 = m MASS (Weight) ounce x 0.02853 = kg pound x 0.4536 = kg ounce x 28.35 = g POWER hp x 0.7457= kW psi x 0.0703= kg/cm2 psi x 6.895 = kPa kg/cm2 x 98.07 = kPa psi x 0.06895 = Bar C= 0.556 (F 32) ft3 x 0.02832 = m3 Gallon x 0.003785= m3 Quart x 0.9464 = L Ounce x 29.57= mL Gallon x 3.7854 = L VOLUME TEMPERATURE PRESSURE

kg x 2.205 = pound g x 0.03527 = ounce kW x 1.340483 = hp kg/cm2 x 14.233578 = psi kPa x .145= psi kPa x 0.010197=kg/cm2 Bar x 14.50377 = psi F = (1.8 x C ) + 32 m3 x 35.31 = ft3 m3 x 264 .17= gallon L x 1.057 = quart L X 0.26418 = gallon

kg = kilogram g =gram kW = kilowatt kg/cm2 = kilogram/ square centimeter kPa = kiloascal

C = degrees Celsius

m3 = cubic meter L = litre mL = milliliter

1227

TECH-H

TECH-H-6 Conversion ChartGallons Per Minute to Barrels Per Day

1 GPM = 34.286 BPD

TECH-H-7 Decimal and Millimeter Equivalents of Fractions

BARRELS PER DAY X 1000 Inches Fractions /64 /32 3 /64 1 /16 5 /64 3 /32 7 /64 1 /8 9 /64 5 /32 11 /64 3 /16 13 /64 7 /32 15 /64 1 /4 17 /64 9 /32 19 /64 5 /16 21 /64 11 /32 23 /64 3 /8 25 /64 13 /32 27 /64 7 /16 29 /64 15 /32 31 /64 1 /2
1 1

GALLONS PER MINUTE

Decimals .015625 .03125 .046875 .0625 .078125 .09375 .109375 .125 .140625 .15625 .171845 .1875 .203125 .21875 .234375 .250 .265625 .28125 .296875 .3125 .328125 .34375 .359375 .375 .390625 .40625 .421875 .4375 .453125 .46875 .484375 .500

Millimeters .397 .794 1.191 1.588 1.984 2.381 2.778 3.175 3.572 3.969 4.366 4.763 5.159 5.556 5.953 6.350 6.747 7.144 7.541 7.938 8.334 8.731 9.128 9.525 9.922 10.319 10.716 11.113 11.509 11.906 12.303 12.700

Inches Fractions /64 /32 35 /64 9 /16 37 /64 19 /32 39 /64 5 /8 41 /64 21 /32 43 /64 11 /16 45 /64 22 /32 47 /64 3 /4 49 /64 25 /32 51 /64 13 /16 53 /64 27 /32 55 /64 7 /8 57 /64 29 /32 59 /64 15 /16 61 /64 31 /32 63 /64 1
33 17

Decimals .515625 .53125 .546875 .5625 .578125 .59375 .609375 .625 .640625 .65625 .671875 .6875 .703125 .71875 .734375 .750 .765625 .78125 .796875 .8125 .828125 .84375 .859375 .875 .890625 .90625 .921875 .9375 .953125 .96875 .984375 1.000

Millimeters 13.097 13.494 13.891 14.288 14.684 15.081 15.487 15.875 16.272 16.669 17.066 17.463 17.859 18.256 18.653 19.050 19.447 19.844 20.241 20.638 21.034 21.431 21.828 22.225 22.622 23.019 23.416 23.813 24.209 24.606 25.003 25.400

TECH-H

1228

TECH-H-8 Atmospheric Pressures and Barometric Readings at Different Altitudes*

Altitude Below or Above Sea Level (Feet) -1000 -500 0 +500 +1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 8500 9000 9500 10,000 15,000 20,000 30,000 40,000 50,000 Barometer Reading Inches Mercury at 32 F 31.02 30.47 29.921 29.38 28.86 28.33 27.82 27.31 26.81 26.32 25.84 25.36 24.89 24.43 23.98 23.53 23.09 22.65 22.22 21.80 21.38 20.98 20.58 16.88 13.75 8.88 5.54 3.44 Atmospheric Pressure (PSI) 15.2 15.0 14.7 14.4 14.2 13.9 13.7 13.4 13.2 12.9 12.7 12.4 12.2 12.0 11.8 11.5 11.3 11.1 10.9 10.7 10.5 10.3 10.1 8.3 6.7 4.4 2.7 1.7 Equivalent Head of Water (75) (Feet) 35.2 34.7 34.0 33.4 32.8 32.2 31.6 31.0 30.5 29.9 29.4 28.8 28.3 27.8 27.3 26.7 26.2 25.7 25.2 24.8 24.3 23.8 23.4 19.1 15.2 10.2 6.3 3.9 213.8 212.9 212.0 211.1 210.2 209.3 208.4 207.4 206.5 205.6 204.7 203.8 202.9 201.9 201.0 200.1 199.2 198.3 197.4 196.5 195.5 194.6 193.7 184 F Boiling Point of Water 101.0 100.5 100.0 99.5 99.0 98.5 98.0 97.4 96.9 96.4 95.9 95.4 94.9 94.4 94.4 93.9 92.9 92.4 91.9 91.4 90.8 90.3 89.8 84.4 C

*Approximate Values

1229

TECH-H

TECH-I-1 Symptoms and Causes of Hydraulic and Mechanical Pump Failure

Hydraulic Failure 1
Pump does not deliver liquid

Section TECH-I Basic Troubleshooting

2

Mechanical Failure 4 5 6 7 8
Pump vibrates at higherthan-normal levels

9
Pump is drawing too much power

10

High rate of mechanical seal failure

Bearings run hot and/or fail on a regular basis

Cause Pump not primed or prime lost Suction and/or discharge valves closed or clogged Suction piping incorrect Insufficient NPSH available Excessive air entrapped in liquid Speed (RPM) too low Incorrect rotation Broken impeller or bent vanes Incorrect impeller or impeller diameter System head too high Instruments give erroneous readings Air leaks in suction line Excessive shaft misalignment Inadequate lubrication Lubricant contamination Inadequate lubricant cooling Axial thrust or radial loads higher than bearing rating Improper coupling lubrication Suction pressure too high Bearing incorrectly installed Impeller out of balance Overheating of seal faces Excessive shaft deflection Lack of seal flush at seal faces Incorrect seal installation Pump is run dry Pump run off design point Shaft/shaft sleeve worn Packing gland not properly adjusted Packing not properly installed Impeller clogged Coupling out of balance Baseplate not installed properly Pump operating speed too close to system's natural frequency Bearing failing Piping not properly anchored Pump and/or driver not secured to baseplate Specific gravity higher than specified Viscosity higher than specified Internal clearances too tight Chemicals in liquid other than specified Pump assembled incorrectly Higher solids concentration than specified

TECH-I

1230

Wear of internal wetted parts is accelerated

Pump does not deliver sufficient pressure

Pump does not deliver sufficient capacity

Packing has short life

Pump delivers flow intermittently

TECH-I-2 Troubleshooting Centrifugal Pumps

Problem Suction line clogged. Impeller clogged with foreign material. Wrong direction of rotation. Pump not primed. Probable Cause Reprime pump, check that pump and suction line are full of liquid. Remove obstructions. Back flush pump to clean impeller. Change rotation to concur with direction indicated by arrow on bearing housing or pump casing. Consult factory for proper depth. Use baffler to eliminate vortices. Shorten suction pipe. Replace gasket. Replace or readjust packing/mechanical seal. Back flush pump to clean impeller. Replace defective part as required. Ensure that suction line shutoff valve is fully open and line is unobstructed. Inspect and replace if necessary. Reprime pump. Rearrange piping to eliminate air pockets. Repair (plug) leak. Re-align pump and drive. Check lubricate for suitability and level. Check cooling system. Align shafts. Back-flush pump to clean impeller. Replace as required. Tighten hold down bolts of pump and motor or adjust stilts. Replace. Anchor per Hydraulic Institute Standards Manual recommendation. System problem. Tighten gland nuts. Check packing and repack box. Replace worn parts. Check lubrication and cooling lines. Remachine or replace as required. Consult factory. Install throttle valve, trim impeller diameter. Check specific gravity and viscosity. Readjust packing. Replace if worn. Check internal wearing parts for proper clearances. Remedy

No liquid delivered.

Pump not producing rated flow or head.

Foot valve or suction pipe opening not submerged enough. Suction lift too high. Air leak through gasket. Air leak through stuffing box. Impeller partly clogged. Worn suction sideplate or wear rings. Insufficient suction head.

Pump starts then stops pumping.

Bearings run hot.

Pump is noisy or vibrates.

Worn or broken impeller. Improperly primed pump. Air or vapor pockets in suction line. Air leak in suction line. Improper alignment. Improper lubrication. Lube cooling. Improper pump/driver alignment. Partly clogged impeller causing imbalance. Broken or bent impeller or shaft. Foundation not rigid.

Excessive leakage from stuffing box/seal chamber.

Worn bearings. Suction or discharge piping not anchored or properly supported. Pump is cavitating. Packing gland improperly adjusted. Stuffing box improperly packed. Worn mechanical seal parts. Overheating mechanical seal. Shaft sleeve scored. Head lower than rating. Pumps too much liquid. Liquid heavier than expected. Stuffing packing too tight. Rotating parts bind.

Motor requires excessive power.

1231

TECH-A TECH-I

TECH-J-1 Keep Air Out of Your Pump

Most centrifugal pumps are not designed to operate on a mixture of liquid and gases. To do so is an invitation to serious mechanical trouble, shortened life and unsatisfactory operation. The presence of relatively small quantities of air can result in considerable reduction in capacity, since only 2% free air will cause a 10% reduction in capacity, and 4% free air will reduce the capacity by 43.5%.

Section TECH-J Miscellaneous Pump Information

When the source of suction supply is above the centerline of the pump, a check for air leaks can be made by collecting a sample in a "bubble bottle" as illustrated. Since the pressure at the suction chamber of the pump is above atmospheric pressure, a valve can be installed in one of the tapped openings at the high point in the chamber and liquid can be fed into the "bubble bottle." The presence of air or vapor will show itself in the "bubble bottle." Connect To Valve Installed At The High Point In Suction Chamber Or Discharge

In addition to a serious loss in efficiency and wasted power, the pump may be noisy with destructive vibration. Entrained air is one of the most frequent causes of shaft breakage. It also may cause the pump to lose its prime and greatly accelerate corrosion. Air may be present in the liquid being pumped due to leaky suction lines, stuffing boxes improperly packed, or inadequately sealed on suction lift or from other sources. Refer also to Section TECH-D-7, Pumping Liquids with Entrained Gas. On the other hand, very small amounts of entrained air (less than 1%) can actually quiet noisy pumps by cushioning the collapse of cavitation bubbles. TESTING FOR AIR IN CENTRIFUGAL PUMPS

To Drain

The amount of air which can be handled with reasonable pump life varies from pump to pump. The elimination of air has greatly improved the operation and life of many troublesome pumps. When trouble occurs, it is common to suspect everything but air, and to consider air last, if at all.

In many cases a great deal of time, inconvenience, and expense can be saved by making a simple test for the presence of air. We will assume that calculations have already been made to determine that there is sufficient NPSH Margin (2 - 5 times the NPSHR) to insure that the noise is not due to cavitation. The next step should be to check for the presence of entrained air in the pumpage.

This test can also be made from a high point in the discharge side.

Obviously, the next step is to eliminate the source of air since quantities present insufficient amount to be audible are almost certain to cause premature mechanical failure. NOTE: The absence of bubbles is not proof that the pumpage doesn't contain air.

TECH-J

1232

TECH-J-2 PS20 Pump Load Monitors

During dry-run conditions, pump power is reduced and recognized by the PumpSmart Pump Load Monitor. During run-out conditions, power increases, which is also a recognizable condition. Power increase is also experienced when internal wear results from upset conditions. Customers may configure the devices to automatically shut down the pump or warn the operator via integrated relay output(s). The PS20 offers two underload and two overload condition protection functions (four total) as well as the ability to output pump load through an integrated 4-20 mA output. A six button keypad and LCD readout enables greater configuration and operation options. The PS20 can be applied on motors up to 999 F.L. Amps. Refer to the PumpSmart Section for additional details.

The PS20 Pump Load Monitors measure the motor input power in combination with a proprietary algorithm to accurately determine the pumps load.

1233

TECH-J

TECH-J-3 Raised Face and Flat Face Flanges (Mating Combinations)

Pumps of cast iron construction are furnished with 125 or 250 lb. flat face (F.F.) flanges. Since industry normally uses fabricated steel piping, the pumps are often connected to 150 or 300 lb. 1/16" raised face (R.F.) steel flanges. Difficulty can occur with this flange mating combination. The pump flange tends to pivot around the edge of the raised face as the flange bolts are tightened. This can cause the pump flange to break allowing leakage at the joint (Fig. 1). The purpose of a R.F. flange is to concentrate more pressure on a smaller gasket area and thereby increase the pressure containment capability of the joint. To create this higher gasket load, it is only necessary to have one-half of the flanged joint supplied with a raised face - not both. The following illustrations show 4" steel R.F. and F.F. mating flange combinations and the gasket loading incurred in each instance. Assuming the force (F) from the flange bolts to be 10,000 lbs. and constant in each combination, the gasket stress is: P (Stress) = Bolt Force (F) Gasket Area P1 (Fig. 4) = 10,000 lbs. = 203 psi 49.4 sq. in. P2 (Fig. 5) = 10,000 lbs = 630 psi P3 (Fig. 6) = 15.9 sq. in.

A similar problem can be encountered when a bronze pump with F.F. flanges is connected to R.F. steel flanges (Fig. 2). Since the materials are not of equal strength, the bronze flange may distort, resulting in leakage. To avoid problems when attaching bronze or cast iron F.F. pump flanges to R.F. steel pipe flanges, the following steps should be taken (refer to Fig. 3). 1. Machine off the raised face on the steel pipe flange. 2. Use a full face gasket.

If the pump is steel or stainless steel with F.F. flanges, no problem arises since materials of equal strength are being connected. Many customers, however, specify R.F. flanges on steel pumps for mating to R.F. companion flanges. This arrangement is technically and practically not required.

It can be readily seen that the smaller gasket, used with a raised face flange, increases the pressure containment capability of a flanged joint. However, it can also be noted that there is no difference in pressure capability between R.F.-to-R.F. and R.F.-to-F.F. flange combinations. 1. The elimination of the extra for R.F. flanges.

In addition to being technically unnecessary to have a R.F.-to-R.F. mating combination, the advantages are: 2. The elimination of the extra delivery time required for a non-standard casing.

Fig. 1

Fig. 2

Fig. 3 Steel Flange With Raised Face Machined Off Full Face Gasket

Steel R.F. Mating Flange

Cast Iron F.F. Pump Flange

Steel R.F. Mating Flange

Bronze F.F. Pump Flange

Cast Iron or Bronze F.F. Pump Flange Fig. 6 Gasket Area 15.9 sq. in.

Fig. 4 Gasket Area 49.4 sq. in.

Fig. 5 Gasket Area 15.9 sq. in.

P1

P1

P2

P2

P3

P3

F.F. to F.F.

R.F. to R.F.

F.F. to R.F.

TECH-J

1234

TECH-J-4 Predictive and Preventive Maintenance Program

This overview of Predictive and Preventive Maintenance (PPM) is intended to assist the pump users who are starting a PPM program or have an interest in the continuous improvement of their current programs. There are four areas that should be incorporated in a PPM program. Individually each one will provide information that gives an indication of the condition of the pump; collectively they will provide a complete picture as to the actual condition of the pump. PUMP PERFORMANCE MONITORING Field Engineer must have is the pump performance curve. With this it can be determined where the pump is performing in some cases without all of the information. PUMP VIBRATION AND BEARING ANALYSIS Vibration analysis is the cornerstone of all PPM programs. Perhaps the question asked most often is "What is the vibration level that indicates the pump is in distress?. The answer is that there is no absolute vibration amplitude level that is indicative of a pump in distress. However, there are several guidelines that have been developed as target values that enable the analyst to set alarm levels. Also many users have developed their own site criteria that is used as a guideline. Institutions such as the Hydraulic Institute and API have developed independent vibration criteria. Caution should be exercised when applying the published values...each installation is unique and should be handled accordingly. When a machine is initially started, a baseline vibration reading should be taken and trended over time. Typically, readings are taken on the motor outboard and inboard bearing housings in the vertical and horizontal directions and on the pump outboard and inboard bearing housings in the vertical and horizontal directions. Additionally, an axial vibration measurement is taken on the pump. The inboard location is defined as the coupling end of the machine. It is critical that when the baseline vibration measurement is taken that the operating point of the pump is also recorded. The vibration level of a pump is directly related to where it is operating and in relation to its Best Efficiency Point (BEP). The further away from the BEP, the higher the vibrations will be. See the following chart for a graphical representation of vibration amplitudevs- flow.

There are six parameters that should be monitored to understand how a pump is performing. They are suction pressure (Ps ), discharge pressure (Pd ), flow (Q), pump speed (Nr ), pumpage properties, and power. Power is easiest measured with a clip on amp meter but some facilities have continuous monitoring systems that can be utilized. In any event, the intent is to determine the BHP of the pump. When using a clip on amp meter, the degree of accuracy is limited. It should not be used to determine the efficiency of the pump. Clip on amp meters are best used for troubleshooting where the engineer is trying to determine the operating point of the pump. The most basic method of determining the TDH of the pump is by utilizing suction and discharge gauges to determine PS and Pd. The installation of the taps for the gauges is very important. Ideally, they should be located normal to the pipe wall and on the horizontal centerline of the pipe. They should also be in a straight section of pipe. Avoid locating the taps in elbows or reducers because the readings will not indicate the true static pressure due to the velocity head component. Avoid locating taps in the top or bottom of the pipe because the gauges can become air bound or clogged with solids. Flow measurements can be difficult to obtain but every effort should be made to do so, especially when troubleshooting. In some new installations permanent flow meters are installed which make the job easier. When this is the case, make sure the flow meters are working properly and have been calibrated on a regular schedule. When flow meters are not installed, pitot tubes can be used. Pitot tubes provide a very accurate measure of flow, but this in an obtrusive device and provisions must be made to insert the tube into the piping. The other method of determining flow is with either a doppler or transitime device. Again, provisions must be made on the piping for these instruments, but these are non-obtrusive devices and are easier to use than the pitot tube. Caution must be exercised because each device must be calibrated, and independent testing has shown these devices are sensitive to the pumpage and are not 100% accurate. An accurate power measurement reading can also be difficult to obtain. Clip on map meters are the most common tool available to the Field Engineer who is troubleshooting a pump problem. In most cases this has proven to be accurate. However, as previously mentioned, this tool must be used and applied properly. Clip on map meters are not accurate enough to determine the actual efficiency of a pump. If accurate horsepower readings are necessary, a torque shaft must be installed but is not very practical in an actual field installation and lends itself to use in a laboratory environment much better. In some critical installations where the user has provided a permanent power monitor, these have varying degrees of accuracy and they must be understood up front.

AMPLITUDE (mlls, In./sec, Gs) CAPACITY (Q) Typical Vibration Level Characteristic vs. Capacity
The engineer must also look at the frequency where the amplitude is occurring. Frequency identifies what the defect is that is causing the problem, and the amplitude is an indication of the severity of the problem. These are general guidelines and do not cover every situation. The spectrum in the chart is a typical spectrum for a pump that has an unbalance condition. Bearing defect analysis is another useful tool that can be used in many condition monitoring programs. Each component of a roller bearing has its own unique defect frequency. Vibration equipment available today enables the engineer to isolate the unique bearing defects and determine if the bearing is in distress. This allows the

Finally, the properties of the pumpage must be known to accurately determine the actual pump performance. Pumpage temperature (Tp), viscosity, and specific gravity (S.G.), must be known. When all of the above parameters are known, it becomes a simple matter of calculating the pump performance. There are instances when it proves to be a very difficult if not an impossible task to determine all of the above parameters in the field, therefore, the Field Engineer must rely on his or her ability to understand where a compromise must be made to get the job done. The basic document the

1235

TECH-J

user to shut the machine down prior to a catastrophic failure. There are several methods utilized but the most practical from a Field Engineering perspective is called bearing enveloping. In this method, special filters built into the analyzer are used to amplify the repetitive high frequency signals in the high frequency range and amplify them in the low frequency part of the vibration spectrum. Bearing manufacturers publish the bearing defect frequency as a function of running speed which allows the engineer to identify and monitor the defect frequency. Similar to conventional vibration analysis, a baseline must be established and then trended. There are other methods available such as High Frequency Detection (HFD), and Spike Energy but the enveloping technology is the latest development. It is a common practice to monitor bearing temperature. The most accurate method to monitor the actual bearing temperature is to use a device that will contact the outer race of the bearing. This requires holes to be drilled into the bearing housings which is not always practical. The other method is the use of an infrared 'gun' where the analyst aims the gun at a point on the bearing housing where the temperature reading is going to be taken. Obviously, this method is the most convenient but there is a downside. The temperature being measured is the outside surface of the bearing housing, not the actual bearing temperature. This must be considered when using this method.

PUMP SYSTEM ANALYSIS

Pump system analysis is often overlooked because it is assumed the system was constructed and operation of the pumps are in accordance with the design specifications. This is often not the case. A proper system analysis begins with a system head curve. System head curves are very difficult to obtain from the end user and, more often than not, are not available. On simple systems, they can be generated in the field but on more complicated systems this can't be done. As has been stated previously, it is imperative to know where the pumps are being operated to perform a correct analysis and this is dependent on the system. A typical system analysis will include the following information; NPSHA, NPSHR, static head, friction loss through the system, and a complete review of the piping configuration and valving. The process must also be understood because it ultimately dictates how the pumps are being operated. All indicators may show the pump is in distress when the real problem is it is being run at low or high flows which will generate high hydraulic forces inside the pump. CONCLUSION A PPM program that incorporates all of the topics discussed will greatly enhance the effectiveness of the program. The more complete understanding the engineer has of the pumping system, the more effective the PPM program becomes.

To complete the condition monitoring portion of a PPM program, many users have begun an oil analysis program. There are several tests that can be performed on the lubricant to determine the condition of the bearing or determine why a bearing failed so appropriate corrective action can be taken. These tests include Spectrographic Analysis, Viscosity Analysis, Infrared Analysis, Total Acid Number, Wear Particle Analysis and Wear Particle Count. Most of these tests have to be performed under laboratory conditions. Portable instruments are now available that enable the user to perform the test on site.

TECH-J

1236