Sand Casting

Ain Shams University
Faculty of Engineering
Sand Casting
March 2008
Sand casting
Sand casting is a method involving pouring a molten metal into a sand
mold.
The typical mold for a sand casting is shown in the picture:
Typical Components of a Two-part Sand Casting Mold.
The set of channels through which a molten metal flows to the mold
cavity is called gating system.
Typical gating system consists of a pouring cup and a sprue receiving

the poured melt, runner – a channel through which the melt is supplied
to the gates through which the molten metal enters the mold cavity.
A gating system may include a riser (feed head) – a cavity connected to

the gating system feeding the casting when it is shrinking.
Air within the mold cavity and gases formed when a molten metal
contacts the mold surface are removed through the vents.
The interior cavities of a casting are formed by a separate inserts called

cores.
Cores are usually made of sand and backed.
A mold frame (flask) consists of two parts: cope (the upper part) and
drag (the lower part).
A mold cavity is formed in the process of pattern molding, when the
pattern (commonly wooden) is embedded in sand in the flask forming an
impression of the casting.
After the sand packing the pattern is removed from the flask and the
cores and the gating system are arranged.
Cores, runner and gates are arranged in the drag; pouring cap and
sprue are placed in the cope.
Then the two parts of the mold are assembled and poured.
After the metal has solidified and cooled to a desired temperature, the
casting is removed from the mold by the process called shakeout.
Patterns
The cavity in the sand is formed by using a pattern (an approximate
duplicate of the real part), which are typically made out of wood,
sometimes metal. The cavity is contained in an aggregate housed in a
box called the flask. Core is a sand shape inserted into the mold to
produce the internal features of the part such as holes or internal
passages. Cores are placed in the cavity to form holes of the desired
shapes. Core print is the region added to the pattern, core, or mold that
is used to locate and support the core within the mold. A riser is an
extra void created in the mold to contain excessive molten material. The
purpose of this is feed the molten metal to the mold cavity as the molten
metal solidifies and shrinks, and thereby prevents voids in the main
casting.
In a two-part mold, which is typical of sand castings, the upper half,

including the top half of the pattern, flask, and core is called cope and
the lower half is called drag. The parting line or the parting surface is
line or surface that separates the cope and drag. The drag is first filled
partially with sand, and the core print, the cores, and the gating system
are placed near the parting line. The cope is then assembled to the drag,
and the sand is poured on the cope half, covering the pattern, core and
the gating system. The sand is compacted by vibration and mechanical
means. Next, the cope is removed from the drag, and the pattern is
carefully removed. The object is to remove the pattern without breaking
the mold cavity. This is facilitated by designing a draft, a slight angular
offset from the vertical to the vertical surfaces of the pattern. This is
usually a minimum of 1° or 1.5 mm (0.060 in), whichever is greater. The
rougher the surface of the pattern, the more the draft to be provided.
Sprues and Runners
The molten material is poured in the pouring cup, which is part of the
gating system that supplies the molten material to the mold cavity. The
vertical part of the gating system connected to the pouring cup is the
sprue, and the horizontal portion is called the runners and finally to the
multiple points where it is introduced to the mold cavity called the
gates. Additionally there are extensions to the gating system called
vents that provide the path for the built up gases and the displaced air
to vent to the atmosphere.
The cavity is usually made oversize to allow for the metal contraction as
it cools down to room temperature. This is achieved by making the
pattern oversize. To account for shrinking, the pattern must be made
oversize by these factors, on the average. These are linear factors and
apply in each direction. These shrinkage allowance are only
approximate, because the exact allowance is determined the shape and
size of the casting. In addition, different parts of the casting might
require a different shrinkage allowance. See the casting allowance table
for the approximate shrinkage allowance expressed as the Pattern
Oversize Factor.
Sand castings generally have a rough surface sometimes with surface

impurities, and surface variations. A machining (finish) allowance is
made for this type of defect. See casting allowance table for the finish
allowance.

Sand Casting

Uploaded by

Copyright:

Available Formats

Sand Casting

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sand Casting

Uploaded by

Copyright:

Available Formats

Ain Shams University

The typical mold for a sand casting is shown in the picture:

Typical Components of a Two-part Sand Casting Mold.

Typical gating system consists of a pouring cup and a sprue receiving

A gating system may include a riser (feed head) – a cavity connected to

The interior cavities of a casting are formed by a separate inserts called

Cores are usually made of sand and backed.

In a two-part mold, which is typical of sand castings, the upper half,

Sand castings generally have a rough surface sometimes with surface

You might also like