Honeywell Actuator M7410E

M7410E
SMALL MODULATING LINEAR VALVE ACTUATOR

PRODUCT DATA
APPLICATION
The Honeywell M7410E actuator is specifically designed to provide modulating control together with the V5812/13, V5822/23,V5872B,D and V5832/33 series of small linear valves. The M7410E is used in fan-coil-units, induction units, small reheaters and recoolers, and for zone control applications. It is employed in electronic temperature control systems with hot and/or cold water as the controlled medium. This actuator is fully compatible with all controllers providing 0 ... 10 V or 2 ... 10 V output signals. The 7410E actuator is designed for applications where space is limited and minimum power consumption is required. A microprocessor-based high performance positioner guarantees accurate control. Reliable longtime operation is ensured due to the fact that no mechanical feedback potentiometer and no mechanical endswitches are needed. Due to an automatic synchronization function the close-off point is self-adjusting. Based on a running time of 150s, valve positioning and flow adjustment is very exact. Manual positioning is provided for all actuators. The actuator is both attractive and robust in design. A special version with auxiliary switch is available.
100%..0% 0%..100% 0..10V 2..10V
FEATURES
Microprocessor based positioner ensures precise stem positioning Small size allows installation where space is limited Low power consumption Suitable for 0 ... 10 V and 2 ... 10 V controller output signal (adjustable on site) Easy-to-operate direct/reverse acting switch Simple input signal override (e.g. for frost protection function) Reliable longtime operation because mechanical feedback potentiometers and mechanical endswitches are not required Magnetic coupling for stem force limitation and selfadjustment of the close-of-point Supplied with pre-wired connection cable Simple, standardized valve/actuator coupling. No tools required for mounting Visual valve position indicator furnished with actuator Manual operation provided by the valve adjustment cap, extra knob, or with a hexagon key
EN0B-097GE51 R0399
PRODUCT DATA
SPECIFICATIONS
Motor
Input voltage: 24 Vac + 15 % ...15 %; 50/60 Hz Power consumption: 1.4 VA Input signal: Operation: Stroke: Running time: Stem force: modulating 0 ... 10 V, 2 ... 10 V (adjustable); <1 mA direct/reverse (adjustable) 6.5 mm 150 s at 50 Hz 120 s at 60 Hz depending on type (see table) 180 N (for valves DN 15..20) 300 N (for valves DN 25..40)
Auxiliary Switches
Ratings: 5 V ... 24 V max. 100 mA 24 Vac ... 230 Vac max. 3(1) A Switch position (factory supplied): Switch S1 (fix) Switch S2 (adjust.) 17.8 0.2 mm 11.7 0.2 mm
OPERATION
The movement of the electric actuator is produced by a screw spindle which is driven in both directions by a synchronous motor through a set of gears. A magnetic clutch limits the torque of the gear assembly and the driving force of the actuator. The actuator is fixed to the valve body by means of a coupling ring requiring no tools for mounting. The actuator is maintenance-free and supplied completely with a ready-towire connecting cable. A microprocessor-based high performance positioner guarantees accurate contol. The close-off position is selfadjusting by means of an automatic synchronization function. Synchronization is carried out when power is switched on and each time the stem reaches 0 % or 100 % of its travel. As long as the synchronization is active the input signal is ignored!
Protection standard: IP 42 in accordance with EN 60529 Insulation class: Connection cable: Ambient operating temperature limits: Weight: Suitable valves: Manual operation: III in accordance with EN 60730 1.5 m 0 ... 55 C 0,4 kg see table see table
VERSIONS
Manual operation Standard Provided by the valve adjustment cap Stem force 180 N 300 N 180 N 300 N 180 N 300 N Aux. switch S1 x x Aux. switch S2 x x Housing type B B C C C C OS number M7410E1002 M7410E1028 M7410E2026 M7410E2034 M7410E4022 M7410E4030 On special request On special request
With manual operation Integrated " With manual operation Integrated and auxiliary switches " Special versions
Bulkpack, 25 actuators incl. 1 manual Special cable length length = XX m
EN0B-097GE51 R0399
PRODUCT DATA
MOUNTING POSITION
The actuator may only be mounted beside or above the valve. Adjust the valve in the right position before mounting the actuator.
SWITCH SELECTION
The built-in selector switches must be set according to the valve type (2-way or 3-way), valve size, and the controller output signal (0 ... 10 V or 2 ... 10 V), see Fig 4.
Valve Type
closing
100%..0% 0%..100% 0..10V 2..10V
Fig.1 Mounting positions
opening
MOUNTING
Before the actuator is fixed to the valve, the adjustment cap must be removed (Fig. 2). Make sure that the actuator is in the open position (factory supplied position) before fixing the actuator to the valve body.
A B
AB
opening
Output Signal Y = 0... +10 V
Y = 2... +10 V
Fig. 2 Remove protection cap The actuator must be mounted by hand. Don't use tools or additional forces, because actuator and valve may be damaged.
Fig. 4 Selecting valve type and output signal
ELECTRIC WIRING
The electrical installation must comply with the wiring diagram shown in Fig 5.
Fig. 5 Wiring colours Fig. 3 Mounting the actuator

3 EN0B-097GE51 R0399
PRODUCT DATA
INPUT SIGNAL OVERRIDE

To override the controller output signal, the input signal must be connected to COM (0 %) or 24 V (100 %) using an external switch (see Fig. 6).
17.8 mm
11.7 mm
Fig. 8 Movement of the actuator stem
AUXILIARY SWITCHES
The actuators with the OS-number M7410E4022 and M7410E4033 are featured with 2 auxiliary switches. Each switch has its own cable. Auxiliary switch S1 with fix switchpoint when the stem position is in. Auxiliary switch S2 with adjustable switchpoint when the stem position is out.
a b c a b c
Fig. 6 Connection of input switch
MANUAL OPERATION
Actuators with the OS-number M7410E2... and M7410E4... are featured with a hexagonal key hole for manual operation. For more comfort an additional knob for the manual adjustment is packed separately. To prevent the valve from damage, the operation may only be done when there is no power applied to the motor. Fig. 9 Auxiliary switch cables
Adjustment of Auxiliary Switch 2

The auxiliary switch should be adjusted by a skilled person only. Move the actuator to the position where the switch is to be operated. Cut the plastic skin with a sharp knife. Below the skin the adjustment screw can be accessed. Turn the screw clockwise until the end stop is reached. Turn the screw counterclockwise until the switch point is achieved. To check the required position has been set, move the actuator. Finally seal the adjustment hole with a piece of tape.
4 mm
Fig. 7 Manual operation
COMMISSIONING ADVICE
A functional check of the valve actuator can be carried out by changing the Y input signal. The movement of the actuator stem (Fig. 8) indicates whether the valve is opening or closing. If the direction of travel is not correct, the direct/reverse-switch must be reset.
EN0B-097GE51 R0399 4
Fig. 10 Adjustment of auxiliary switch S2
PRODUCT DATA
Electric Wiring of Auxiliary Switches

The electrical installation must comply with the wiring diagram shown in Fig. 11. If the auxiliary switch is connected to 230 Vac, a switch with a contact gap of at least 3 mm for each pole must be fitted with the installation.
24 Vac: max. 100 mA
Application Example: Switch off electrical Appliance

2-Way-Valve
DN 15, DN 20
(230 Vac only):
230 Vac: max. 5 (1)A
M7410E
E. g. fan, pump etc.
BLUE
max. 5 (1)A
BLACK
Fig. 12 Electric wiring of auxiliary switch

open
DN 15, DN 20
close
All other Valves

B
DN 15 - DN 40
DN 15 - DN 20
DN 25 - DN 40
close
DN 25 DN 40
A B A B A
open
close
DN 15 DN 40
A B AB A
open
E. g. fan, pump etc.
A B
AB
AB
BLUE
B
max. 5 (1)A
BLACK
close
DN 15 DN 20
A B AB A B AB A
open
AB B
BROWN BLUE BLACK BLUE
BROWN BLACK BLUE
BROWN BLACK
BROWN BLUE BLACK BLUE
BROWN BLACK BLUE
BROWN BLACK

5 EN0B-097GE51 R0399
PRODUCT DATA
DIMENSIONS (MM)
58
82
100
109
49
60
49 87
Fig. 15 Housing type B
Fig. 16 Housing type C
Home and Building Control Products Honeywell AG Bblinger Strae 17 D-71101 Schnaich Phone (49-7031) 637-01 Fax (49-7031) 637-493 http://europe.hbc.honeywell.com Subject to change without notice. Printed in Germany.
EN0B-097GE51 R0399
Manufacturing location is certified to
DIN EN ISO 9001

Honeywell Actuator M7410E

Uploaded by

Copyright:

Available Formats

Honeywell Actuator M7410E

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Honeywell Actuator M7410E

Uploaded by

Copyright:

Available Formats

M7410E

SMALL MODULATING LINEAR VALVE ACTUATOR

100%..0% 0%..100% 0..10V 2..10V

Bulkpack, 25 actuators incl. 1 manual Special cable length length = XX m

Fig.1 Mounting positions

Output Signal Y = 0... +10 V

Fig. 4 Selecting valve type and output signal

Fig. 5 Wiring colours Fig. 3 Mounting the actuator

INPUT SIGNAL OVERRIDE

Fig. 8 Movement of the actuator stem

Fig. 6 Connection of input switch

Adjustment of Auxiliary Switch 2

Fig. 7 Manual operation

Fig. 10 Adjustment of auxiliary switch S2

Electric Wiring of Auxiliary Switches

Application Example: Switch off electrical Appliance

(230 Vac only):

230 Vac: max. 5 (1)A

E. g. fan, pump etc.

Fig. 12 Electric wiring of auxiliary switch

All other Valves

Fig. 13 Electric wiring of auxiliary switch

BROWN BLUE BLACK BLUE

BROWN BLACK BLUE

BROWN BLUE BLACK BLUE

BROWN BLACK BLUE

Fig. 11 Electric wiring of auxiliary switch

Fig. 15 Housing type B

Fig. 16 Housing type C

Manufacturing location is certified to

DIN EN ISO 9001

You might also like