FIM10

NITGEN FIM10

Stand-Alone Fingerprint Identification Device with Built-in CPU

Datasheet

Version 1.11

NITGEN ____________________________________________________________ Page: 1 FIM10 Datasheet

FIM10

Copyright 2004 NITGEN Co., Ltd.

ALL RIGHTS RESERVED

Serial Number:

Specifications can be changed without notice.

NITGEN ____________________________________________________________ Page: 2 FIM10 Datasheet

FIM10
Revision History Date of Revision February 11, 2004 March 23, 2004 Version 1.0 1.11 Release Revision 1.11 Description

NITGEN ____________________________________________________________ Page: 3 FIM10 Datasheet

FIM10
General Descriptions
FIM10 is a stand-alone Fingerprint Identification Device with many excellent features. It provides benefits such as high identification performance, low power consumption and RS-232 serial interface with the simple protocol for easy integration into a wide range of applications. It is a durable and compact device with fingerprint identification module containing NITGEN opticsbased fingerprint sensor inside. There are two types of process board depending on supply voltage and sensor.

Basic Feature (FIM10 series)

ITEM FIM10-HV FIM10-LV

Board Spec Dimension Sensor Supply Voltage Current Consumption Operating Temperature Humidity ESD Tolerance Communication Speed External I/O Capture Speed Verification Speed Boot Up Time (100 users) Data Encryption Method The number of MAX fingers (2 images per 1 finger) Special Function

S3C2410 (ARM9), 8M SDRAM, 1MB Flash 2 43 x 60 [mm ] NITGEN OPP01MM2 5 0.2 [V] 60(Idle) ~ 210(Op.) [mA] -20 ~ 60 [] 5 ~ 95 [% RH] 10 [KV] (indirect) 9600 ~ 115200 [bps] 3 input port, 2 output port 0.4(normal) / 0.7(secure) sec 1.2 [sec] (Capture + Extract + Match) 0.34 [sec] AES in flash memory 100 Fast identification, Cancel, Adaptive capture for dry, wet, small finger

S3C2410 (ARM9), 8M SDRAM, 1MB Flash 2 43 x 60 [mm ] NITGEN OPP02MM1 3.3 0.1 [V] 60(Idle) ~ 200 (Op.) [mA] -20 ~ 60 [] 5 ~ 95 [% RH] 10 [KV] (indirect) 9600 ~ 115200 [bps] 3 input port, 2 output port 0.4(normal) / 0.7(secure) sec 1.2 [sec] (Capture + Extract + Match) 0.34 [sec] AES in flash memory 100 Fast identification, Cancel, Adaptive capture for dry, wet, small finger

NITGEN ____________________________________________________________ Page: 4 FIM10 Datasheet

FIM10
Application
Door-Lock System Safe Box Simple Access Controller Vehicle Control ATM, POS, etc

Block Diagram

NITGEN Fingerprint Sensor OPP01 or OPP02

I2C VCLK DATA

Processor

UART (RS232)

RS232 (RX/TX)

Host Controller

Memory

I/O

FDA12 FIM10

User Enrollment User Deletion User Identification Operation Success Operation Fail

RS-232C communication data consist of 8-bit data, no parity, 1-bit start-bit and 1-bit stop-bit.

NITGEN ____________________________________________________________ Page: 5 FIM10 Datasheet

FIM10
FIM10 Technical Data
n The Features of FIM10 board
Front Side
(Unit: mm)

(JP2) SENSOR

(JP4)

(JP1) JTAG

(JP3) POWER

NITGEN ____________________________________________________________ Page: 6 FIM10 Datasheet

FIM10
Rear side

NITGEN ____________________________________________________________ Page: 7 FIM10 Datasheet

FIM10
n Optical fingerprint sensor
l The dimensions of OPP01 (Unit: mm)

* FIM10-HV does only support OPP01MM2.

NITGEN ____________________________________________________________ Page: 8 FIM10 Datasheet

FIM10

The dimensions of OPP02

y
7

* FIM10-LV does only support OPP02MM1.

NITGEN ____________________________________________________________ Page: 9 FIM10 Datasheet

FIM10
n External Port
l Pin 1 2 3 4 5 6 7 8 9 JTAG Connector (JP1) Pin Name VCC 3.3 Volt Power N/A N/A nSRST JTAG control pin TDO JTAG control pin TDI JTAG control pin nTRST JTAG control pin TCK JTAG control pin TMS JTAG control pin GND Ground

Description

* JP1 (JTAG connector) is used only for development or emergency recovery. l Name GND VCLK SDATA0 SDATA1 SDATA2 SDATA3 SDA SCL VCC 9-Pin Sensor Connection (JP2) No 1 2 3 4 5 6 7 8 9 States POWER IN OUT OUT OUT OUT IN IN POWER Description Sensor Ground Sensor Clock Sensor Data0 Sensor Data1 Sensor Data2 Sensor Data3 Sensor SDA Sensor SCL Sensor VCC (FIM10-HV: +5V / FIM10-LV: +3.3V)

NITGEN ____________________________________________________________ Page: 10 FIM10 Datasheet

FIM10

l Pin 1 2 3 4 5 6 7 8 9

9-Pin External Connector (JP3) Pin Name Description VCC FIM10-HV: 5V / FIM10-LV: 3.3 V EXT_RXD RS-232C port receiving signals from host EXT_TXD RS-232C port transmitting signals to host EXT_PASS External output for indicating authentication success EXT_FAIL External output for indicating authentication fail EXT_ENROLL External Input to enroll fingerprint without RS-232 communication EXT_DELETE External Input to delete user without RS-232 communication EXT_IDENTIFY External Input to identify user without RS-232 communication GND Ground

l Pin 4 5 6 7 8

I/O Port Operation Condition Direction Out Out In In In Initial State Low Low High High High Active State High (500 ms) High (500 ms) Low (more 30ms) Low (more 30ms) Low (more 30ms)

Name EXT_PASS EXT_FAIL EXT_ENROLL EXT_DELETE EXT_IDENTIFY l

Reserved Port for future use (JP4) No 1 2 3 4 5 6 7 8 9 Description FIM10-HV: 5V / FIM10-LV: 3.3 V

Name VCC

VCC

Ground

* This connector is reserved for future use. So FIM10 which has no JP4 connector is delivered.

NITGEN ____________________________________________________________ Page: 11 FIM10 Datasheet

FIM10
n Cables
l Cable for Sensor

l NO
1 2 3

Material List DESCRIPTION 9-PIN HOUSING 1.25mm(51021-0900) 9-PIN HOUSING 1.25mm(51021-0900) CABLE 9P, 180mm VENDOR MOLEX MOLEX UL

l PIN 1 2 3 4 5 6 7 8 9

9-Pin Connector COLOR BLACK WHITE WHITE WHITE WHITE WHITE WHITE WHITE RED SIGNAL GND CLK DATA0 DATA1 DATA2 DATA3 SDA SCL VCC

NITGEN ____________________________________________________________ Page: 12 FIM10 Datasheet

FIM10
APPENDIX
n Recommended External Interface
l

Standalone with built-in CPU

Input Port (internal pull-up) ? EXT_ENROLL, EXT_DELETE, EXT_IDENTIFY

+3.3V

CPU 10K R SW0 SW1 SW2

Output Port (COMS level output)

VIN

R 470

LED

FIM10

R7

Q 4.7K 2

EXT_PASS /EXT_FAIL

CPU

NITGEN _______________________________________________________ Page: 13 FIM10 Standalone with built-in CPU

FIM10
n Boot up time

Standalone with built-in CPU

Power

RESETn

Identify Enable

tpi

Registered user 0 20 50 100

Boot up time (tpi) 276 m sec 290 m sec 308 m sec 334 m sec

* Boot up time increases in proportion to the number of registered users.

NITGEN _______________________________________________________ Page: 14 FIM10 Standalone with built-in CPU

FIM10
Ordering Information
n

Standalone with built-in CPU

Ordering Guide
Part No FIM10-HV FIM10-LV Sensor OPP01MM2 OPP02MM1 Power 5V 3.3V Board Size 43x60mm

* OPP01MM2 and OPP02MM1 are modules that order names of sensor provided by NITGEN. n

The label of sensor

OPP01MM2 OPP02MM1

NITGEN _______________________________________________________ Page: 15 FIM10 Standalone with built-in CPU

FIM10
Support Information

Standalone with built-in CPU

NITGEN Co., Ltd.

Sanhak Foundation Bldg. 5F, 1337-31, Seocho-dong, Seocho-gu, Seoul, Korea Tel: +82-2-3415-1800 Fax: +82-2-3415-1801
E-mail. [email protected]

NITGEN _______________________________________________________ Page: 16 FIM10 Standalone with built-in CPU