0% found this document useful (0 votes)
145 views18 pages

1 Dept. of Electronics & Communication

The document discusses different types of optical amplifiers used in fiber optic systems. It focuses on erbium-doped fiber amplifiers (EDFAs), which are commonly used to amplify signals in the 1,550 nm wavelength range. EDFAs work by pumping erbium-doped fiber with lasers at 980 nm or 1,480 nm, causing stimulated emission that amplifies the input signal. The document provides diagrams of basic and multi-stage EDFA components and configuration. It explains how EDFAs are able to amplify signals over long distances without the need for repeaters.

Uploaded by

Apurva Sharma
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
145 views18 pages

1 Dept. of Electronics & Communication

The document discusses different types of optical amplifiers used in fiber optic systems. It focuses on erbium-doped fiber amplifiers (EDFAs), which are commonly used to amplify signals in the 1,550 nm wavelength range. EDFAs work by pumping erbium-doped fiber with lasers at 980 nm or 1,480 nm, causing stimulated emission that amplifies the input signal. The document provides diagrams of basic and multi-stage EDFA components and configuration. It explains how EDFAs are able to amplify signals over long distances without the need for repeaters.

Uploaded by

Apurva Sharma
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 18

OPTICAL AMPLIFIERS

TABLE OF CONTENTS
INTRODUCTION.2 TYPES OF AMPLIFIERS3 DOPED FIBER AMPLIFIERS.3 ERBIUM-DOPED FIBER AMPLIFIERS ..................................................................................................... 4 Noise ......................................................................................................................................... 11 Gain saturation ........................................................................................................................ 12 Inhomogeneous broadening effects......................................................................................... 13 Polarization effects................................................................................................................... 13 SEMICONDUCTOR OPTICAL AMPLIFIERS.14 VERTICAL-CAVITY SOA..16 CONCLUSION18 REFERENCES.19

DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

OPTICAL AMPLIFIERS
INTRODUCTION
An optical amplifier is a device that amplifies an optical signal directly, without the need to first convert it to an electrical signal. An optical amplifier may be thought of as a laser without an optical cavity, or one in which feedback from the cavity is suppressed. Optical amplifiers are important in optical

communication and laser physics. With the demand for longer transmission lengths, optical amplifiers have become an essential component in long-haul fiber optic systems. Semiconductor optical amplifiers (SOAs), erbium doped fiber amplifiers (EDFAs), and Raman optical amplifiers lessen the effects of dispersion and attenuation allowing improved performance of long-haul optical systems. There are several different physical mechanisms that can be used to amplify a light signal, which correspond to the major types of optical amplifiers. In doped fiber amplifiers and bulk lasers, stimulated emission in the amplifier's gain

medium causes amplification of incoming light. In semiconductor optical amplfiers (SOAs), electron-hole recombination occurs. In Raman amplifiers, Raman

scattering of incoming light with phonons in the lattice of the gain medium producesphotons coherent with the incoming photons. Parametric amplifiers use parametric amplfication.

DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

TYPES OF OPTICAL AMPLIFIERS


Semiconductor Optical Amplifiers (SOAs) Erbium Doped Fiber Amplifiers (EDFAs) Raman Amplifiers Hybrid Amplifiers

LASER AMPLIFIERS
Almost any laser active gain medium can be pumped to produce gain for light at the wavelength of a laser made with the same material as its gain medium. Such amplifiers are commonly used to produce high power laser systems. Special types such as regenerative amplifiers and chirped-pulse amplifiers are used to

amplify ultra short pulses.

DOPED FIBER AMPLIFIERS


Doped fiber amplifiers (DFAs) are optical amplifiers that use a doped optical fiber as a gain medium to amplify an optical signal. They are related to fiber lasers. The signal to be amplified and a pump laser are multiplexed into the doped fiber, and the signal is amplified through interaction with the doping ions. The most common example is the Erbium Doped Fiber Amplifier (EDFA), where the core of a silica fiber is doped with trivalent Erbium ions and can be efficiently pumped with a laser at a wavelength of 980 nm or 1,480 nm, and exhibits gain in the 1,550 nm region.

DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

ERBIUM-DOPED FIBER AMPLIFIERS


The erbium-doped fiber amplifier (EDFA) is the most deployed fiber amplifier as its amplification window coincides with the third transmission window of silicabased optical fiber. Two bands have developed in the third transmission window the Conventional, or C-band, from approximately 1525 nm 1565 nm, and the Long, or L-band, from approximately 1570 nm to 1610 nm. Both of these bands can be amplified by EDFAs, but it is normal to use two different amplifiers, each optimized for one of the bands. The principal difference between C- and L-band amplifiers is that a longer length of doped fiber is used in L-band amplifiers. The longer length of fiber allows a lower inversion level to be used, thereby giving at longer wavelengths (due to the band-structure of Erbium in silica) while still providing a useful amount of gain. EDFAs have two commonly-used pumping bands 980 nm and 1480 nm. The 980 nm band has a higher absorption cross-section and is generally used where low-noise performance is required. The absorption band is relatively narrow and so wavelength stabilized laser sources are typically needed. The 1480 nm band has a lower, but broader, absorption cross-section and is generally used for higher power

DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

amplifiers. A combination of 980 nm and 1480 nm pumping is generally utilised in amplifiers. The explosion of dense wavelength-division multiplexing (DWDM) applications makes these optical amplifiers an essential fiber optic system building block. EDFAs allow information to be transmitted over longer distances without the need for conventional repeaters. The fiber is doped with erbium, a rare earth element, that has the appropriate energy levels in their atomic structures for amplifying light. EDFAs are designed to amplify light at 1550 nm. The device utilizes a 980 nm or 1480nm pump laser to inject energy into the doped fiber. When a weak signal at 1310 nm or 1550 nm enters the fiber, the light stimulates the rare earth atoms to release their stored energy as additional 1550 nm or 1310 nm light. This process continues as the signal passes down the fiber, growing stronger and stronger as it goes. Figure 2 shows a fully featured, dual pump EDFA that includes all of the common components of a modern EDFA.

The input coupler, Coupler #1, allows the microcontroller to monitor the input light via detector #1. The input isolator, isolator #1 is almost always present. WDM #1 is always present, and provides a means of injecting the 980 nm pump wavelength into the length of erbium-doped fiber. WDM #1 also allows the optical input signal to be coupled into the erbium-doped fiber with minimal optical loss. The erbium-doped optical fiber is usually tens of meters long. The 980 nm energy pumps the erbium atom into a slowly decaying, excited state. When energy in the 1550 nm band travels through the fiber it causes stimulated emission of radiation, much like in a laser, allowing the 1550 nm signal to gain strength. The erbium fiber has relatively high optical loss, so its length is optimized to provide maximum power output in the desired 1550 nm band. WDM #2 is present only in dual pumped EDFAs. It couples additional 980 nm energy from Pump Laser #2
5 DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

into the other end of the erbium-doped fiber, increasing gain and output power. Isolator #3 is almost always present. Coupler #2 is optional and may have only one of the two ports shown or may be omitted altogether. The tap that goes to Detector #3 is used to monitor the optical output power. The tap that goes to Detector #2 is used to monitor reflections back into the EDFA.

Block

Diagram

of

an

EDFA

This feature can be used to detect if the connector on the optical output has been disconnected. This increases the backreflected signal, and the microcontrolled can set to disable the pump lasers in this event, providing a measure of safety for technicians working with EDFAs. Figure 3 shows a two-stage EDFA with midstage access. In this case, two single-stage EDFAs are packaged together. The output of the first stage EDFA and the input of the second stage EDFA are brought
6 DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

out the user. Mid-stage access is important in high performance fiber optic systems. To reduce the overall dispersion of the system, dispersion compensating fiber (DCF) can be used periodically. However, problems can arise from using the DCF, mostly the insertion loss reaching 10 dB. Placing the DCF at the mid-stage access point of the two-stage EDFA reduces detrimental effects on the system, and allows the users noticeable gain.

Two-stage EDFA with Mid-stage Access

The optical input first passes through optical Isolator #1. Next the light passes through WDM #1, which provides a means of injecting the 980 nm pump wavelength into the first length of erbium-doped fiber. WDM #1 also allows the optical input signal to be coupled into the erbium-doped fiber with minimal optical loss. The erbium-doped optical fiber is usually tens of meters long. Like the fully
7 DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

feature, dual pumped EDFA, the 980 nm energy pumps the erbium atoms into an excited state that decays slowly. When light in the 1550 nm band travels through the erbium-doped fiber it causes stimulated emission of radiation. As the optical signal gains strength, output of the erbium-doped fiber then goes into the optical isolator #2, the output of which is available to the user. Typically, a dispersion compensating device will be connected at the mid-stage access point. The light then travels through isolator #3 and WDM #2, which couples additional 980 nm energy from a second pump laser into the other end of a second length of erbiumdoped fiber, increasing gain and output power. Finally, the light travels through isolator #4. Photons amplify the signal avoiding almost all active components, a benefit of EDFAs. Since the output power of an EDFA can be large, any given system design can require fewer amplifiers. Yet another benefit of EDFAs is the data rate independence means that system upgrades only require changing the launch/receive terminals. The most basic EDFA design amplifies light over a narrow, 12 nm, band. Adding gain equalization filters can increase the band to more than 25 nm. Other exotic doped fibers increase the amplification band to 40 nm. Because EDFAs greatly enhance system performance, they find use in longhaul, high data rate fiber optic communication systems and CATV delivery systems. Long-haul systems need amplifiers because of the lengths of fiber used. CATV applications often need to split a signal to several fibers, and EDFAs boost the signal before and after the fiber splits. There are four major applications that generally require optical fiber amplifiers: power amplifier/booster, in-line amplifier, preamplifier or loss compensation for optical networks. Below are detailed description of each application. Power Amplifier/Booster Figure 4 illustrates the first three application for optical amplifiers. Power amplifiers (also referred to as booster amplifiers) are placed directly after the optical transmitter. This application requires the EDFA to take a large signal input and provide the
8 DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

maximum output level. Small signal response is not as important because the direct transmitter output is usually -10 dBm or higher. The noise added by the amplifier at this point is also not as critical because the incoming signal has a large signal-tonoise ratio (SNR).

Three

Applications

for

an

EDFA

In-Line Amplifiers In-line amplifiers or in-line repeaters, modify a small input signal and boost it for retransmission down the fiber. Controlling the small signal performance and noise added by the EDFA reduces the risk of limiting a system's length due to the noise produced by the amplifying components. Preamplifiers Past receiver sensitivity of -30 dBm at 622 Mb/s was acceptable; however, presently, the demands require sensitivity of -40 dBm or -45 dBm. This performance can be achieved by placing an optical amplifier prior to the receiver. Boosting the signal at this point presents a much larger signal into the receiver, thus easing the demands of the receiver design. This application requires careful attention to the noise added by the EDFA; the noise added by the amplifier must be minimal to maximize the received SNR. Compensating for Loss in Optical Networks Inserting an EDFA before an 8 x 1 optical splitter increases the power to almost +19 dBm
9 DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

allowing each of the eight output legs to provide +9 dBm, making the output almost equal to the original transmitter power. The optical splitter alone has a nominal optical insertion loss of 10 dB. The transmitter has an optical output of +10 dBm, meaning that the optical splitter outputs without an EDFA would be 0 dBm. This output power would be acceptable for most digital applications; however, in analog CATV applications this is the minimal acceptable received power. Therefore, inserting the EDFA before the optical splitter greatly increases the output power.

Loss Compensation in Optical Networks

Wideband EDFAs Optical communication systems carrying 100 or more optical wavelengths require and increase in the bandwidth of the optical amplifier to nearly 80 nm. Normally employing a hybrid optical amplifier, consisting of two separate optical amplifiers, allows for separate amplification, one for the lower 40 nm band and the second for the upper 40 nm band. Figure 6 exemplifies the optical gain spectrum of a hybrid optical amplifier. The solid lines illustrate the response of two individual amplifier sections. The dotted line, which has been increased by

10

DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

1 dB for clarity, shows the response of the combined hybrid amplifier.

Optical Gain Spectrum of a Hybrid Optical Amplifier

The optical fiber amplifier was invented by H. J. Shaw and Michel Digonnet at Stanford University, California, in the early 1980s. The EDFA was first demonstrated several years later by a group including David N. Payne, R. Mears, and L. Reekie, from the University of Southampton and a group from AT&T Bell Laboratories, E. Desurvire, P. Becker, and J. Simpson.

Noise The principal source of noise in DFAs is Amplified Spontaneous Emission (ASE), which has a spectrum approximately the same as the gain spectrum of the amplifier. Noise figure in an ideal DFA is 3 dB, while practical amplifiers can have noise figure as large as 68 dB.
11 DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

As well as decaying via stimulated emission, electrons in the upper energy level can also decay by spontaneous emission, which occurs at random, depending upon the glass structure and inversion level. Photons are emitted spontaneously in all directions, but a proportion of those will be emitted in a direction that falls within the numerical aperture of the fiber and are thus captured and guided by the fiber. Those photons captured may then interact with other dopant ions, and are thus amplified by stimulated emission. The initial spontaneous emission is therefore amplified in the same manner as the signals, hence the term Amplified Spontaneous Emission. ASE is emitted by the amplifier in both the forward and reverse directions, but only the forward ASE is a direct concern to system performance since that noise will co-propagate with the signal to the receiver where it degrades system performance. Counter-propagating ASE can, however, lead to degradation of the amplifier's performance since the ASE can deplete the inversion level and thereby reduce the gain of the amplifier. Gain saturation Gain is achieved in a DFA due to population inversion of the dopant ions. The inversion level of a DFA is set, primarily, by the power of the pump wavelength and the power at the amplified wavelengths. As the signal power increases, or the pump power decreases, the inversion level will reduce and thereby the gain of the amplifier will be reduced. This effect is known as gain saturation as the signal level increases, the amplifier saturates and cannot produce any more output power, and therefore the gain reduces. Saturation is also commonly known as gain compression. To achieve optimum noise performance DFAs are operated under a significant amount of gain compression (10 dB typically), since that reduces the rate of spontaneous emission, thereby reducing ASE. Another advantage of operating the
12 DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

DFA in the gain saturation region is that small fluctuations in the input signal power are reduced in the output amplified signal: smaller input signal powers experience larger (less saturated) gain, while larger input powers see less gain. The leading edge of the pulse is amplified, until the saturation energy of the gain medium is reached. In some condition, the width (FWHM) of the pulse is reduced.

Inhomogeneous broadening effects


Due to the inhomogeneous portion of the linewidth broadening of the dopant ions, the gain spectrum has an inhomogeneous component and gain saturation occurs, to a small extent, in an inhomogeneous manner. This effect is known as Spectral hole burning because a high power signal at one wavelength can 'burn' a hole in the gain for wavelengths close to that signal by saturation of the inhomogeneously broadened ions. Spectral holes vary in width depending on the characteristics of the optical fiber in question and the power of the burning signal, but are typically less than 1 nm at the short wavelength end of the C-band, and a few nm at the long wavelength end of the C-band. The depth of the holes are very small, though, making it difficult to observe in practice.

Polarization effects
Although the DFA is essentially a polarization independent amplifier, a small proportion of the dopant ions interact preferentially with certain polarizations and a small dependence on the polarization of the input signal may occur (typically < 0.5 dB). This is called Polarization Dependent Gain (PDG). The absorption and emission crossections of the ions can be modeled as ellipsoids with the major axes aligned at random in all directions in different glass sites. The random distribution of the orientation of the ellipsoids in a glass produces a macroscopically isotropic medium, but a strong pump laser induces an anisotropic distribution by selectively
13 DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

exciting those ions that are more aligned with the optical field vector of the pump. Also, those excited ions aligned with the signal field produce more stimulated emission. The change in gain is thus dependent on the alignment of the polarizations of the pump and signal lasers i.e. whether the two lasers are interacting with the same sub-set of dopant ions or not. In an ideal doped fiber without birefringence, the PDG would be inconveniently large. Fortunately, in optical fibers small amounts of birefringence are always present and, furthermore, the fast and slow axes vary randomly along the fiber length. A typical DFA has several tens of meters, long enough to already show this randomness of the birefringence axes. These two combined effects (which in transmission fibers give rise to polarization mode dispersion) produce a misalignment of the relative polarizations of the signal and pump lasers along the fiber, thus tending to average out the PDG. The result is that PDG is very difficult to observe in a single amplifier (but is noticeable in links with several cascaded amplifiers).

SEMICONDUCTOR OPTICAL AMPLIFIERS


Semiconductor optical amplifiers (SOAs) are essentially laser diodes, without end mirrors, which have fiber attached to both ends. They amplify any optical signal that comes from either fiber and transmit an amplified version of the signal out of the second fiber. SOAs are typically constructed in a small package, and they work for 1310 nm and 1550 nm systems. In addition, they transmit bidirectionally, making the reduced size of the device an advantage over regenerators of EDFAs. However, the drawbacks to SOAs include high-coupling

loss, polarization dependence, and a higher noise figure. Figure 1 illustrates the basics of a Semiconductor optical amplifier. Semiconductor optical amplifiers (SOAs) are amplifiers which use a

semiconductor to provide the gain medium. These amplifiers have a similar


14 DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

structure toFabryProt laser diodes but with anti-reflection design elements at the endfaces. Recent designs include anti-reflective coatings and tilted waveguide and window regions which can reduce endface reflection to less than 0.001%. Since this creates a loss of power from the cavity which is greater than the gain it prevents the amplifier from acting as a laser.
Semiconductor Optical Amplifier

Semiconductor optical amplifiers are typically made from group III-V compound semiconductors such as GaAs/AlGaAs, InP/InGaAs, InP/InGaAsP

andInP/InAlGaAs, though any direct band gap semiconductors such as II-VI could conceivably be used. Such amplifiers are often used in telecommunication systems in the form of fiber-pigtailed components, operating at signal wavelengths between 0.85 m and 1.6 m and generating gains of up to 30 dB. The semiconductor optical amplifier is of small size and electrically pumped. It can be potentially less expensive than the EDFA and can be integrated with semiconductor lasers, modulators, etc. However, the performance is still not comparable with the EDFA. The SOA has higher noise, lower gain, moderate polarization dependence and high nonlinearity with fast transient time. The main
15 DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

advantage of SOA is that all four types of nonlinear operations (cross gain modulation, cross phase modulation, wavelength conversion and four wave mixing) can be conducted. Furthermore, SOA can be run with a low power laser. This originates from the short nanosecond or less upper state lifetime, so that the gain reacts rapidly to changes of pump or signal power and the changes of gain also cause phase changes which can distort the signals. This nonlinearity presents the most severe problem for optical communication applications. However it provides the possibility for gain in different wavelength regions from the EDFA. "Linear optical amplifiers" using gain-clamping techniques have been developed. Modern optical networks utilize SOAs in the follow ways: Power Boosters: Many tunable laser designs output low optical power levels and must be immediately followed by an optical amplifier. ( A power booster can use either an SOA or EDFA.) In-Line Amplifier: Allows signals to be amplified within the signal path. Wavelength Conversion: Involves changing the wavelength of an optical signal. Receiver Preamplifier: SOAs can be placed in front of detectors to enhance sensitivity.

VERTICAL-CAVITY SOA
A recent addition to the SOA family is the vertical-cavity SOA (VCSOA). These devices are similar in structure to, and share many features with, vertical-cavity surface-emitting lasers (VCSELs). The major difference when comparing VCSOAs and VCSELs is the reduced mirror reflectivities used in the amplifier cavity. With VCSOAs, reduced feedback is necessary to prevent the device from reaching lasing threshold. Due to the extremely short cavity length, and correspondingly thin gain medium, these devices exhibit very low single-pass gain (typically on the order of a few percent) and also a very large free spectral range (FSR). The small single-pass gain requires relatively high mirror
16 DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

reflectivities to boost the total signal gain. In addition to boosting the total signal gain, the use of the resonant cavity structure results in a very narrow gain bandwidth; coupled with the large FSR of the optical cavity, this effectively limits operation of the VCSOA to single-channel amplification. Thus, VCSOAs can be seen as amplifying filters. Given their vertical-cavity geometry, VCSOAs are resonant cavity optical amplifiers that operate with the input/output signal entering/exiting normal to the wafer surface. In addition to their small size, the surface normal operation of VCSOAs leads to a number of advantages, including low power consumption, low noise figure, polarization insensitive gain, and the ability to fabricate high fill factor two-dimensional arrays on a single semiconductor chip. These devices are still in the early stages of research, though promising preamplifier results have been demonstrated.

CONCLUSION
In the past few years research into all-optical amplification has been intensified. The performance expectations of both semiconductor and fibre amplifiers are becoming better understood and the number of possible applications is rapidly increasing. The particular attraction of linear optical amplifiers is that in most cases they offer very wide bandwidths, up to 5 THz, which is attractive for many of the wideband signaling schemes proposed for future networks. Thus it is hoped that optical amplifiers will allow the direct amplification of wavelength- and frequency-division multiplexing and other wideband schemes such as subcarrier modulation. There is still considerable work to be done, however, in evaluating the amplifier performance in certain cases, for example in the presence of a large number of closely spaced channels.

17

DEPT. OF ELECTRONICS & COMMUNICATION

OPTICAL AMPLIFIERS

REFERENCES

1. Mears, R.J. and Reekie, L. and Poole, S.B. and Payne, D.N.: "Lowthreshold tunable CW and Q-switched fiber laser operating at 1.55m", Electron. Lett., 1986, 22, pp.159-160 2. R.J. Mears, L. Reekie, I.M. Jauncey and D. N. Payne: Low-noise Erbiumdoped fiber amplifier at 1.54m, Electron. Lett., 1987, 23, pp.10261028 3. E. Desurvire, J. Simpson, and P.C. Becker, High-gain erbium-doped traveling-wave fiber amplifier," Optics Letters, vol. 12, No. 11, 1987, pp. 888890 4. M. J. Connelly, Semiconductor Optical Amplifiers. Boston, MA: SpringerVerlag, 2002. ISBN 978-0-7923-7657-6 5. Ghosh, B.; Mukhopadhyay, S. (2011). "All-Optical Wavelength encoded NAND and NOR Operations exploiting Semiconductor Optical Amplifier based Mach-Zehnder Interferometer Wavelength Converter and Phase Conjugation System".

18

DEPT. OF ELECTRONICS & COMMUNICATION

You might also like