Scribd
Upload
107 views6 pages

Computer Network Notes CS 602 LN 4

This document discusses various methods of digital-to-analog and analog-to-analog conversion used in computer networks. It describes techniques such as amplitude shift keying, frequency shift keying, and phase shift keying that are used to convert digital signals to analog for transmission. It also discusses analog modulation techniques including amplitude, frequency, and phase modulation. Additionally, it covers bandwidth utilization methods like frequency-division multiplexing, wavelength-division multiplexing, and time-division multiplexing that allow multiple analog signals to be combined onto a single transmission medium or channel.

Uploaded by

sujoy.bhowmick
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
107 views6 pages

Computer Network Notes CS 602 LN 4

This document discusses various methods of digital-to-analog and analog-to-analog conversion used in computer networks. It describes techniques such as amplitude shift keying, frequency shift keying, and phase shift keying that are used to convert digital signals to analog for transmission. It also discusses analog modulation techniques including amplitude, frequency, and phase modulation. Additionally, it covers bandwidth utilization methods like frequency-division multiplexing, wavelength-division multiplexing, and time-division multiplexing that allow multiple analog signals to be combined onto a single transmission medium or channel.

Uploaded by

sujoy.bhowmick
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

COMPUTER NETWORK

LECTURE NOTES Volume-4

COMPUTER NETWORK

LECTURE NOTES Volume-4

Analog Transmission
DIGITAL-TO-ANALOG CONVERSION
Digital-to-analog conversion is the process of changing one of the characteristics of an analog signal based on the information in digital data.

Figure: Binary amplitude shift keying

TYPES OF DIGITAL TO ANALOG CONVERSION:

Figure: Implementation of binary ASK

Bit rate is the number of bits per second. Baud rate is the number of signal elements per second. In the analog transmission of digital data, the baud rate is less than or equal to the bit rate. An analog signal carries 4 bits per signal element. If 1000 signal elements are sent per second, find the bit rate. Solution In this case, r = 4, S = 1000, and N is unknown. We can find the value of N from Figure: Binary frequency shift keying An analog signal has a bit rate of 8000 bps and a baud rate of 1000 baud. How many data elements are carried by each signal element? How many signal elements do we need? Solution In this example, S = 1000, N = 8000, and r and L are unknown. We find first the value of r and then the value of L. Figure: Implementation of binary FSK

SUJOY BHOWMICK (Asst. Prof, IT)

PAGE NO : 1

SUJOY BHOWMICK (Asst. Prof, IT)

PAGE NO : 2

COMPUTER NETWORK

LECTURE NOTES Volume-4

COMPUTER NETWORK

LECTURE NOTES Volume-4

Figure: Binary phase shift keying

Figure: Concept of a constellation diagram Show the constellation diagrams for an ASK (OOK), BPSK, and QPSK signals. Solution

Figure: Implementation of BASK

Figure : shows the three constellation diagrams. Quadrature amplitude modulation is a combination of ASK and PSK.

Figure: Constellation diagrams for some QAMs

ANALOG TO ANALOG CONVERSION


Analog-to-analog conversion is the representation of analog information by an analog signal. One may ask why we need to modulate an analog signal; it is already analog. Modulation is needed if the medium is bandpass in nature or if only a bandpass channel is available to us. Figure: QPSK and its implementation

SUJOY BHOWMICK (Asst. Prof, IT)

PAGE NO : 3

SUJOY BHOWMICK (Asst. Prof, IT)

PAGE NO : 4

COMPUTER NETWORK
Topics Discussed in Here: Amplitude Modulation Frequency Modulation Phase Modulation Types of analog-to-analog modulation

LECTURE NOTES Volume-4

COMPUTER NETWORK

LECTURE NOTES Volume-4

Figure: Frequency modulation The total bandwidth required for FM can be determined from the bandwidth of the audio signal: BFM = 2(1 + )B.

Figure: Amplitude modulation The total bandwidth required for AM can be determined from the bandwidth of the audio signal: BAM = 2B. Figure: Phase modulation The total bandwidth required for PM can be determined from the bandwidth and maximum amplitude of the modulating signal: BPM = 2(1 + )B.

SUJOY BHOWMICK (Asst. Prof, IT)

PAGE NO : 5

SUJOY BHOWMICK (Asst. Prof, IT)

PAGE NO : 6

COMPUTER NETWORK

LECTURE NOTES Volume-4

COMPUTER NETWORK
FDM process:

LECTURE NOTES Volume-4

Bandwidth Utilization: Multiplexing and Spreading


Bandwidth utilization is the wise use of available bandwidth to achieve specific goals. Efficiency can be achieved by multiplexing; privacy and anti-jamming can be achieved by spreading.

MULTIPLEXING
Whenever the bandwidth of a medium linking two devices is greater than the bandwidth needs of the devices, the link can be shared. Multiplexing is the set of techniques that allows the simultaneous transmission of multiple signals across a single data link. As data and telecommunications use increases, so does traffic. Topics discussed in this section: Frequency-Division Multiplexing Wavelength-Division Multiplexing Synchronous Time-Division Multiplexing Statistical Time-Division Multiplexing

Figure : Dividing a link into channels Categories of multiplexing:

Frequency-division multiplexing

FDM is an analog multiplexing technique that combines analog signals.

SUJOY BHOWMICK (Asst. Prof, IT)

PAGE NO : 7

SUJOY BHOWMICK (Asst. Prof, IT)

PAGE NO : 8

COMPUTER NETWORK

LECTURE NOTES Volume-4

COMPUTER NETWORK

LECTURE NOTES Volume-4

Figure: Multilevel multiplexing

FIGURE: Analog Hierarchy

Wavelength-division multiplexing:

Figure: Multiple-slot multiplexing

WDM is an analog multiplexing technique to combine optical signals.

Figure: Pulse stuffing

Time-division multiplexing:

TDM is a digital multiplexing technique for combining several low-rate channels into one high-rate one.

Figure : Digital hierarchy

SUJOY BHOWMICK (Asst. Prof, IT)

PAGE NO : 9

SUJOY BHOWMICK (Asst. Prof, IT)

PAGE NO : 10

COMPUTER NETWORK

LECTURE NOTES Volume-4

Figure : T-1 line for multiplexing telephone lines

SUJOY BHOWMICK (Asst. Prof, IT)

PAGE NO : 11

You might also like