Surface Mount Aluminum Electrolytic Capacitors

EXV Series, 105C

Overview

Applications
Typical applications include audio/visual (AV), computer/monitor, communications, and switch mode power supplies (SMPS).

KEMET's EXV Series of aluminum electrolytic surface mount capacitors are designed for applications requiring ultra-low impedance and a low profile vertical chip.

Benefits
Surface mount lead terminals Low profile vertical chip Ultra-low impedance 105C / 3,000 5,000 hours

Part Number System

EXV
Series Surface Mount Aluminum Electrolytic

226
Capacitance Code (pF) Digits 4 5 represent the first two digits of the capacitance value. The final digit indicates the number of zeros to be added.

M
Tolerance M = 20%

6R3
Rated Voltage (VDC) 6R3 = 6.3 010 = 10 016 = 16 025 = 25 035 = 35 050 = 50

A
Electrical Parameters A = Standard

9B
Size Code See Dimension Table

AA
Packaging AA = Tape & Reel

One world. One KEMET

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com A4003_EXV 10/9/2012 1

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Dimensions Millimeters

G
F

Size Code
9B 9D 9G 9H 9L 9M 9P

D
Nominal 4 5 6.3 6.3 8 8 10 Tolerance 0.5 0.5 0.5 0.5 0.5 0.5 0.5 Nominal 5.4 5.4 5.4 7.7 6.2 10.2 10.2

L
Tolerance +0.25/-0.1 +0.25/-0.1 +0.25/-0.1 0.3 0.3 0.3 0.3 Nominal 4.3 5.3 6.6 6.6 8.3 8.3 10.3

A/B
Tolerance 0.2 0.2 0.2 0.2 0.2 0.2 0.2 Nominal 5.5 6.5 7.8 7.8 9.5 10 13

C
Tolerance Maximum Maximum Maximum Maximum Maximum Maximum Maximum Nominal 1.8 2.2 2.6 2.6 3.4 3.4 3.5

E
Tolerance 0.2 0.2 0.2 0.2 0.2 0.2 0.2

Size Code
9B 9D 9G 9H 9L 9M 9P

F
Nominal 0.3 0.3 0.3 0.3 0.3 0.3 0.3 Tolerance Maximum Maximum Maximum Maximum Maximum Maximum Maximum Nominal 0.35 0.35 0.35 0.35 0.35 0.70 0.70

G
Tolerance +0.15/-0.2 +0.15/-0.2 +0.15/-0.2 +0.15/-0.2 +0.15/-0.2 0.2 0.2 Nominal 1.0 1.5 1.8 1.8 2.2 3.1 4.6

P
Tolerance 0.2 0.2 0.2 0.2 0.2 0.2 0.2 Nominal 0.65 0.65 0.65 0.65 0.65 0.9 0.9

W
Tolerance 0.1 0.1 0.1 0.1 0.1 0.2 0.2

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Performance Characteristics
Item
Capacitance Range Capacitance Tolerance Rated Voltage Life Test Operating Temperature Leakage Current 1.0 1,000 F 20% at 120 Hz / 20C 6.3 50 VDC 3,000 5,000 hours (see conditions in Test Method & Performance) -40C to +105C I 0.01 CV or 3 A C = rated capacitance (F), V = rated voltage (VDC). Voltage applied for 2 minutes at 20C.

Performance Characteristics

Compensation Factor of Ripple Current (RC) vs. Frequency

Frequency Coefficient 120 Hz 0.70 1 kHz 0.80 10 kHz 0.90 100 kHz 1.00

Test Method & Performance

Conditions
Temperature Test Duration Ripple Current Voltage Can = 4, 5, 6.3 mm Can = 8, 10 mm

Load Life Test

105C 3,000 hours 5,000 hours

Shelf Life Test

105C 1,000 hours No ripple current applied No voltage applied

Maximum ripple current specified at 120 Hz 85C The sum of DC voltage and the peak AC voltage must not exceed the rated voltage of the capacitor.

Performance
Capacitance Change Dissipation Factor Leakage Current

The following specifications will be satisfied when the capacitor is restored to 20C:
Within 20% of the initial value Does not exceed 200% of the specified value Does not exceed specified value

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Environmental Compliance
As an environmentally conscious company, KEMET is working continuously with improvements concerning the environmental effects of both our capacitors and their production. In Europe (RoHS Directive) and in some other geographical areas like China, legislation has been put in place to prevent the use of some hazardous materials, such as lead (Pb), in electronic equipment. All products in this catalog are produced to help our customers obligations to guarantee their products and fulfill these legislative requirements. The only material of concern in our products has been lead (Pb), which has been removed from all designs to fulfill the requirement of containing less than 0.1% of lead in any homogeneous material. KEMET will closely follow any changes in legislation world wide and makes any necessary changes in its products, whenever needed. Some customer segments such as medical, military and automotive electronics may still require the use of lead in electrode coatings. To clarify the situation and distinguish products from each other, a special symbol is used on the packaging labels for RoHS compatible capacitors. Because of customer requirements, there may appear additional markings such as LF = Lead Free or LFW = Lead Free Wires on the label.

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Table 1 Ratings & Part Number Reference

VDC
6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 10 10 10 10 10 10 10 10 10 16 16 16 16 16 16 16 16 25 25 25 25 25 25 25 25 25 35 35 35 35 35 35 35 35 35 50 50 50 50 50 50 50 50 50 50

VDC Surge Voltage

8 8 8 8 8 8 8 8 8 8 13 13 13 13 13 13 13 13 13 20 20 20 20 20 20 20 20 32 32 32 32 32 32 32 32 32 44 44 44 44 44 44 44 44 44 63 63 63 63 63 63 63 63 63 63

Rated Capacitance 120 Hz 20C (F)

22 33 47 100 150 220 330 470 680 1000 22 33 47 100 150 220 330 470 680 22 33 47 100 150 220 330 470 10 22 33 47 68 100 150 220 330 4.7 10 22 33 47 68 100 150 220 1 2.2 3.3 4.7 10 22 33 47 68 100

Case Size D x L (mm)

4x5.4 4x5.4 5x5.4 6.3x5.4 6.3x7.7 6.3x7.7 8x10.2 8x10.2 10x10.2 10x10.2 4 x 5.4 5 x 5.4 6.3 x 5.4 6.3 x 5.4 6.3 x 7.7 8 x 10.2 8 x 10.2 10 x 10.2 10 x 10.2 5 x 5.4 6.3 x 5.4 6.3 x 5.4 6.3 x 7.7 8 x 10.2 8 x 10.2 8 x 10.2 10 x 10.2 4 x 5.4 5 x 5.4 6.3 x 5.4 6.3 x 5.4 6.3 x 7.7 6.3 x 7.7 8 x 10.2 8 x 10.2 10 x 10.2 4 x 5.4 5 x 5.4 5 x 5.4 6.3 x 5.4 6.3 x 7.7 6.3 x 7.7 8 x 10.2 10 x 10.2 10 x 10.2 4 x 5.4 4 x 5.4 4 x 5.4 5 x 5.4 6.3 x 5.4 6.3 x 7.7 8 x 10.2 10 x 10.2 10 x 10.2 10 x 10.2

DF 120 Hz 20C (tan %)

26 26 26 26 26 26 26 26 26 26 19 19 19 19 19 19 19 19 19 16 16 16 16 16 16 16 16 14 14 14 14 14 14 14 14 14 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

RC 100 kHz 105C (mA)

90 90 160 240 240 240 600 600 850 850 90 160 190 190 240 600 600 850 850 160 240 240 280 370 370 600 850 90 160 240 240 280 300 600 600 850 90 160 160 240 280 280 600 850 850 60 60 60 95 140 230 350 670 670 670

Z 100 kHz 20C ()

1.93 1.93 1 0.52 0.3 0.3 0.16 0.16 0.12 0.12 1.93 1 0.52 0.52 0.34 0.16 0.16 0.12 0.12 1 0.52 0.52 0.34 0.22 0.22 0.16 0.12 1.93 1 0.52 0.52 0.34 0.26 0.16 0.16 0.12 1.93 1 1 0.52 0.34 0.34 0.16 0.12 0.12 5 5 5 4 2.6 1.3 0.5 0.34 0.34 0.34

Part Number
EXV226M6R3A9BAA EXV336M6R3A9BAA EXV476M6R3A9DAA EXV107M6R3A9GAA EXV157M6R3A9HAA EXV227M6R3A9HAA EXV337M6R3A9MAA EXV477M6R3A9MAA EXV687M6R3A9PAA EXV108M6R3A9PAA EXV226M010A9BAA EXV336M010A9DAA EXV476M010A9GAA EXV107M010A9GAA EXV157M010A9HAA EXV227M010A9MAA EXV337M010A9MAA EXV477M010A9PAA EXV687M010A9PAA EXV226M016A9BAA EXV336M016A9GAA EXV476M016A9GAA EXV107M016A9HAA EXV157M016A9MAA EXV227M016A9MAA EXV337M016A9MAA EXV477M016A9PAA EXV106M025A9BAA EXV226M025A9DAA EXV336M025A9GAA EXV476M025A9GAA EXV686M025A9HAA EXV107M025A9HAA EXV157M025A9MAA EXV227M025A9MAA EXV337M025A9PAA EXV475M035A9BAA EXV106M035A9DAA EXV226M035A9DAA EXV336M035A9GAA EXV476M035A9HAA EXV686M035A9HAA EXV107M035A9MAA EXV157M035A9PAA EXV227M035A9PAA EXV105M050A9BAA EXV225M050A9BAA EXV335M050A9BAA EXV475M050A9DAA EXV106M050A9GAA EXV226M050A9HAA EXV336M050A9MAA EXV476M050A9PAA EXV686M050A9PAA EXV107M050A9PAA

VDC

VDC Surge

Rated Capacitance

Case Size

DF

RC

Part Number

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

Roll Over for Order Info.

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Mounting Positions (Safety Vent)

In operation, electrolytic capacitors will always conduct a leakage current which causes electrolysis. The oxygen produced by electrolysis will regenerate the dielectric layer but, at the same time, the hydrogen released may cause the internal pressure of the capacitor to increase. The overpressure vent (safety vent) ensures that the gas can escape when the pressure reaches a certain value. All mounting positions must allow the safety vent to work properly.

Installing
A general principle is that lower-use temperatures result in a longer, useful life of the capacitor. For this reason, it should be ensured that electrolytic capacitors are placed away from heat-emitting components. Adequate space should be allowed between components for cooling air to circulate, particularly when high ripple current loads are applied. In any case, the maximum category temperature must not be exceeded. Do not deform the case of capacitors or use capacitors with a deformed case. Verify the correct polarization of the capacitor on the board. It is recommended that capacitors always be mounted with the safety device uppermost or in the upper part of the capacitor. If the capacitors are stored for a long time, the leakage current must be verified. If the leakage current is superior to the value listed in this catalog, the capacitors must be reformed. In this case, they can be reformed by application of the rated voltage through a series resistor approximately 1 k for capacitors with VR 160 V (5 W resistor) and 10 k for the other rated voltages. In the case of capacitors connected in series, a suitable voltage sharing must be used. In the case of balancing resistors, the approximate resistance value can be calculated as: R = 60/C KEMET recommends, nevertheless, to ensure that the voltage across each capacitor does not exceed its rated voltage.

Application and Operation Guidelines

Electrical Ratings: Capacitance (ESC) Capacitance is measured by applying an alternate voltage of 0.5 V at a frequency of 120 or 100 Hz and 20C. Temperature Dependence of the Capacitance Capacitance of an electrolytic capacitor depends upon temperature: with decreasing temperature the viscosity of the electrolyte increases, thereby reducing its conductivity. Capacitance will decrease if temperature decreases. Furthermore, temperature drifts cause armature dilatation and, therefore, capacitance changes (up to 20% depending on the series considered, from 0 to 80C). This phenomenon is more evident for electrolytic capacitors than for other types.

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Frequency Dependence of the Capacitance Effective capacitance value is derived from the impedance curve, as long as impedance is still in the range where the capacitance component is dominant. C= 1 2 fZ C = Capacitance (F) f = Frequency (Hz) Z = Impedance ()

Dissipation Factor tan (DF) Dissipation Factor tan is the ratio between the active and reactive power for a sinusoidal waveform voltage. It can be thought of as a measurement of the gap between an actual and ideal capacitor.

reactive

ideal

actual active

Tan is measured with the same set-up used for the series capacitance ESC. tan = x ESC x ESR where: ESC = Equivalent Series Capacitance ESR = Equivalent Series Resistance Equivalent Series Inductance (ESL) Self inductance or Equivalent Series Inductance results from the terminal configuration and internal design of the capacitor.
Capacitor Equivalent Internal Circuit

Equivalent Series Capacitance (ESC)

Equivalent Series Resistance (ESR)

Equivalent Series Inductance (ESL)

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Equivalent Series Resistance (ESR) Equivalent Series Resistance is the resistive component of the equivalent series circuit. ESR value depends on frequency and temperature and is related to the tan by the following equation: tan 2f ESC ESR = Equivalent Series Resistance () tan = Dissipation Factor ESC = Equivalent Series Capacitance (F) f = Frequency (Hz)
Ce

Co

Re

ESR =

Tolerance limits of the rated capacitance must be taken into account when calculating this value. Impedance (Z)

Co
L

Re

Impedance of an electrolytic capacitor results from a circuit formed by the following individual equivalent series components:

Co

Re

Ce

Ce

Co = Aluminum oxide capacitance (surface and thickness of the dielectric) Re = Resistance of electrolyte and paper mixture (other resistances not depending on the frequency are not considered: tabs, plates, etc.) Ce = Electrolyte soaked paper capacitance L = Inductive reactance of the capacitor winding and terminals Impedance of an electrolytic capacitor is not a constant quantity that retains its value under all conditions; it changes depending on frequency and temperature. Impedance as a function of frequency (sinusoidal waveform) for a certain temperature can be represented as follows:
Z [ohm]

1000 100 10 1 0.1

1/ Ce B A 1/ Co C L

Re

0.1

10

100

1000

10000
F [KHz]

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Capacitive reactance predominates at low frequencies With increasing frequency, capacitive reactance Xc = 1/Co decreases until it reaches the order of magnitude of electrolyte resistance Re(A) At even higher frequencies, resistance of the electrolyte predominates: Z = Re (A - B) When the capacitors resonance frequency is reached (0), capacitive and inductive reactance mutually cancel each other 1/Ce = L, 0 = C1/LCe Above this frequency, inductive reactance of the winding and its terminals (XL = Z = L) becomes effective and leads to an increase in impedance Generally speaking, it can be estimated that Ce 0.01 Co. Impedance as a function of frequency (sinusoidal waveform) for different temperature values can be represented as follows (typical values):
Z (oh m )

1000 100 10 1 0.1 0.1 1 10

-4 0C 2 0C 8 5C

10 F

100

1000

1 0 0 00

F (K H z) Re is the most temperature-dependent component of an electrolytic capacitor equivalent circuit. Electrolyte resistivity will decrease if temperature rises.

In order to obtain a low impedance value throughout the temperature range, Re must be as little as possible. However, Re values that are too low indicate a very aggressive electrolyte, resulting in a shorter life of the electrolytic capacitor at high temperatures. A compromise must be reached. Leakage Current (LC) Due to the aluminum oxide layer that serves as a dielectric, a small current will continue to flow even after a DC voltage has been applied for long periods. This current is called leakage current. A high leakage current flows after applying voltage to the capacitor then decreases in a few minutes, e.g., after prolonged storage without any applied voltage. In the course of continuous operation, the leakage current will decrease and reach an almost constant value. After a voltage-free storage the oxide layer may deteriorate, especially at high temperature. Since there are no leakage currents to transport oxygen ions to the anode, the oxide layer is not regenerated. The result is that a higher than normal leakage current will flow when voltage is applied after prolonged storage. As the oxide layer is regenerated in use, the leakage current will gradually decrease to its normal level.
KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com A4003_EXV 10/9/2012 9

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

The relationship between the leakage current and voltage applied at constant temperature can be shown schematically as follows:

VR

VS

VF

Where: VF = Forming voltage If this level is exceeded, a large quantity of heat and gas will be generated and the capacitor could be damaged. VR = Rated voltage This level represents the top of the linear part of the curve. VS = Surge voltage This lies between VR and VF. The capacitor can be subjected to VS for short periods only. Electrolytic capacitors are subjected to a reforming process before acceptance testing. The purpose of this preconditioning is to ensure that the same initial conditions are maintained when comparing different products. Ripple Current (RC) The maximum ripple current value depends on: Ambient temperature Surface area of the capacitor (heat dissipation area) tan or ESR Frequency The capacitors life depends on the thermal stress. Frequency Dependence of the Ripple Current ESR and, thus, the tan depend on the frequency of the applied voltage. This indicates that the allowed ripple current is also a function of the frequency. Temperature Dependence of the Ripple Current The data sheet specifies maximum ripple current at the upper category temperature for each capacitor.

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

10

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Expected Life Calculation Expected life depends on operating temperature according to the following formula: L = Lo x 2 (To-T)/10 Where: L: Expected life Lo: Load life at maximum permissible operating temperature T: Actual operating temperature To: Maximum permissible operating temperature This formula is applicable between 40C and To.

Packaging Quantities
Size Code
9B 9D 9G 9H 9L 9M 9P

Diameter (mm)
4 5 6.3 6.3 8 8 10

Length (mm)
5.4 5.4 5.4 7.7 6.2 10.2 10.2

Reel Quantity
2000 1000 1000 1000 1000 500 500

Box Quantity (4 Reels per box)

20000 10000 10000 10000 10000 4000 4000

Standard Marking for Surface Mount Types

Capacitance (F) Rated Voltage (VDC) Series Indentification Negative Polarity: Black Row
100 50 X 201

Date Code (YMM)

Note: 6.3 V rated voltage shall be marked as 6 V, but 6.3 V shall be assured.

Series Rated voltage (VDC) Capacitance (F) Negative polarity: black line

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

11

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Lead Taping & Packaging

Case Size (mm)
4 x 5.4 5 x 5.4 6.3 x 5.4 6.3 x 7.7 8 x 6.2 8 x 10.2 10 x 10.2 12.5 x 13.5 12.5 x 16 16 x 16.5

0.2

Reel H
0.8 21 21 21 21 21 21 21 23 23 23

1.0 14 14 18 18 18 26 26 34 34 46

380

Taping for Automatic Insertion Machines

Feeding hole t1 A B D0 P2 P0 E F P1 Chip component Tape running direction Chip pocket

t2

Dimensions (mm)
Tolerance 4 x 5.4 5 x 5.4 6.3 x 5.4 6.3 x 7.7 8 x 6.2 8 x 10.2 10 x 10.2 12.5 x 13.5 12.5 x 16 16 x 16.5

W
Nominal 12 12 16 16 16 24 24 32 32 44

A
Nominal 4.7 5.7 7 7 8.7 8.7 10.7 13.4 13.4 17.5

B
Nominal 4.7 5.7 7 7 8.7 8.7 10.7 13.4 13.4 17.5

P0
0.1 4 4 4 4 4 4 4 4 4 4

P1
0.1 8 12 12 12 12 16 16 24 24 28

P2
0.1 2 2 2 2 2 2 2 2 2 2

F
Nominal 5.5 5.5 7.5 7.5 7.5 11.5 11.5 14.2 14.2 20.2

D0
0.1 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5

E
Nominal 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75

t1
Nominal 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.5 0.5 0.5

t2
Nominal 5.8 5.8 5.8 5.8 6.8 11 11 14 17.5 17.5

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

12

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Construction
The manufacturing process begins with the anode foil being electrochemically etched to increase the surface area and then formed to produce the aluminum oxide layer. Both the anode and cathode foils are then interleaved with absorbent paper and wound into a cylinder. During the winding process, aluminum tabs are attached to each foil to provide the electrical contact. The deck, complete with terminals, is attached to the tabs and then folded down to rest on top of the winding. The complete winding is impregnated with electrolyte before being housed in a suitable container, usually an aluminum can, and sealed. Throughout the process, all materials inside the housing must be maintained at the highest purity and be compatible with the electrolyte. Each capacitor is aged and tested before being sleeved and packed. The purpose of aging is to repair any damage in the oxide layer and thus reduce the leakage current to a very low level. Aging is normally carried out at the rated temperature of the capacitor and is accomplished by applying voltage to the device while carefully controlling the supply current. The process may take several hours to complete. Damage to the oxide layer can occur due to variety of reasons: Slitting of the anode foil after forming Attaching the tabs to the anode foil Minor mechanical damage caused during winding A sample from each batch is taken by the quality department after completion of the production process. The following tests are applied and may be varied at the request of the customer. In this case the batch, or special procedure, will determine the course of action. Electrical: Leakage current Capacitance ESR Impedance Tan Delta Mechanical/Visual: Overall dimensions Torque test of mounting stud Print detail Box labels Packaging, including packed quantity

Extended cathode Anode foil

Foil tabs

Tissues Cathode foil

Etching Forming Winding Decking Impregnation Assembly Aging Testing Sleeving Packing

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

13

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

KEMET Corporation World Headquarters

2835 KEMET Way Simpsonville, SC 29681 Mailing Address: P.O. Box 5928 Greenville, SC 29606 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Corporate Offices Fort Lauderdale, FL Tel: 954-766-2800

Europe
Southern Europe Paris, France Tel: 33-1-4646-1006 Sasso Marconi, Italy Tel: 39-051-939111 Central Europe Landsberg, Germany Tel: 49-8191-3350800 Kamen, Germany Tel: 49-2307-438110 Northern Europe Bishops Stortford, United Kingdom Tel: 44-1279-460122 Espoo, Finland Tel: 358-9-5406-5000

Asia
Northeast Asia Hong Kong Tel: 852-2305-1168 Shenzhen, China Tel: 86-755-2518-1306 Beijing, China Tel: 86-10-5829-1711 Shanghai, China Tel: 86-21-6447-0707 Taipei, Taiwan Tel: 886-2-27528585 Southeast Asia Singapore Tel: 65-6586-1900 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817

North America
Southeast Lake Mary, FL Tel: 407-855-8886 Northeast Wilmington, MA Tel: 978-658-1663 Central Novi, MI Tel: 248-994-1030 West Milpitas, CA Tel: 408-433-9950 Mexico Guadalajara, Jalisco Tel: 52-33-3123-2141

Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com A4003_EXV 10/9/2012 14

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Other KEMET Resources

Tools
Resource Configure A Part: CapEdge SPICE & FIT Software Search Our FAQs: KnowledgeEdge http://capacitoredge.kemet.com http://www.kemet.com/spice http://www.kemet.com/keask Location

Product Information
Resource Products Technical Resources (Including Soldering Techniques) RoHS Statement Quality Documents http://www.kemet.com/products http://www.kemet.com/technicalpapers http://www.kemet.com/rohs http://www.kemet.com/qualitydocuments Location

Product Request
Resource Sample Request Engineering Kit Request http://www.kemet.com/sample http://www.kemet.com/kits Location

Contact
Resource Website Contact Us Investor Relations Call Us Twitter www.kemet.com http://www.kemet.com/contact http://www.kemet.com/ir 1-877-MyKEMET http://twitter.com/kemetcapacitors Location

Disclaimer
All product specifications, statements, information and data (collectively, the Information) are subject to change without notice. All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute and we specifically disclaim any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required.

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

15

Surface Mount Aluminum Electrolytic Capacitors EXV Series, 105C

Digitally signed by Jeannette Calvo DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corp., ou=Marketing Communications, cn=Jeannette Calvo, [email protected] Date: 2012.10.10 16:18:34 -04'00'

KEMET Electronics Corporation P.O. Box 5928 Greenville, SC 29606 (864) 963-6300 www.kemet.com

A4003_EXV 10/9/2012

16