Buster Kite

BUILD A
3. Place the third dowel 4 inches up from the point of

intersection of the first two dowels. Place this dowel in
between the first two dowels and lash at points B and C.
BUSTER KITE
Courtesy of Boy Scout Troop 18, Stephenville, Tex., and Boys’ Lifemagazine
For more on kites, including plans to build a simple “tetrahedral” kite,
see the March 2000 issue of Boys’ Life.
I
n 1932, two boys in central Texas created a rare kite that
could fly better than any known to the boys at that time.
The unusual three-stick kite design had a 25-foot tail and
flew well at 800 feet. The boys were shocked when they dis-
covered their kites could fly all day and night, crashing only
once, when the wind died completely. In later years one
crashed when a low-flying airplane collided with the string.
One of the boys, William “Buster” Robertson, added a
parachute drop to the kite, making it his favorite hobby.
Over the years, Buster made it his personal quest to teach 4. Cover all three lash points with glue. Let dry completely.
as many boys as possible how to make the entertaining 5. Cut the ends off the third dowel so it measures 12 inch-
kite. He wanted boys to stay out of trouble and have fun. es out from both points B and C.
Today Buster’s relatives still honor his wishes by sharing
plans for these unusual kites.
WHAT YOU’LL NEED:

• Three 3-foot dowels, 14⁄ inch diameter
• Sheet of butcher paper
• 25 feet of medium-weight fabric for tail
• Handkerchief or other small fabric for parachute
• Small fish hook, swivel and weight
• Glue
• Scissors
• Nylon kite string
• Light string for parachute
• Pocketknife
6. Using a knife, gently cut a notch around the entire tip
WHAT YOU’LL DO: of each end of the three dowels.
1. On two dowels, measure 18 inches from the end and
mark the spot.
2. Lay the two marked dowels over each other to form an
X. Lash together at the location of the marks as shown.
7. Using nylon string, outline the frame, starting and end-

ing at point D.
8. Lay the frame on the butcher paper and cut a pattern kite’s flyability. A darting or diving kite needs more tail.
the same shape as the kite. Cut the edges two inches larger 14. Using about 2 feet of lightweight string, tie two oppo-
than the frame so it can fold over and cover the kite string. site corners of handkerchief together. The string should
Cut a V in the paper at the tip of each end of dowel. (Note: hang like a loop between the corners. Repeat this on the
You may need to glue to pieces of butcher paper together two remaining corners.
to make it large enough to cover the frame.) 15. Hook the two strings over your finger and gently pull
on the handkerchief corners until they are all hanging
evenly. Tie one knot in the two strings close to your hand.
This will leave 2 small string loops.
16. Cut the barb off a fish hook and connect the hook to one
of the loops. Tie a fishing weight to the other loop. The amount
of weight may vary, but usually one small weight is O.K.
9. Fold the edges of the paper over the string and glue in
place. Your butcher paper should now be attached to the kite.
10. Tie a 4-foot piece of nylon string from point E to point
F, in the notched ends of the dowels. Let it hang across the
surface of the kite on the side opposite the sticks.
11. Punch a tiny hole through the covering over point A
(where the sticks were first lashed together). Tie a 4-foot
piece of string at point A and run it through the hole to the
side of the kite opposite the sticks. Tie it around the string
going from E to F. Tie it in a manner that will produce three
equal lengths of string coming out of points E, F and A.
This will make the shape of a triangle when you look at the
face of the kite. This triangle is the flying bridle. Tie a loop 17. To fly the parachute place the hook on the kite flight
in the end of the excess string that comes up from point A. line. The wind will open the parachute and blow it up the
12. Tie a 4-foot piece of string from point H to point I. Tie string toward the kite in the sky. When the parachute gets
a loop in the middle of the string for connecting the tail. close to the kite, flip the string with a simple wrist action to
release the parachute into free flight.
• Buster kites are very stable fliers. Adjusting the tail length or
bridle knot position will produce good results.
• No need to run to get this kite off the ground. If the wind is
blowing it will rise from your hand.
• Be sure the tail isn’t dragging during takeoff.
• These kites fly very high, so be sure to stay away from power
lines, trees and other obstacles.
Buster Kites
P.O. Box 8
Hico, TX 76457
13. Attach a 25-foot tail made of medium-weight cloth. This

will vary from kite to kite and can only be made more accurate
during flight. Lengthening or shortening the tail will adjust the

Buster Kite

Uploaded by

Copyright:

Available Formats

Buster Kite

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Buster Kite

Uploaded by

Copyright:

Available Formats

BUILD A

3. Place the third dowel 4 inches up from the point of

WHAT YOU’LL NEED:

7. Using nylon string, outline the frame, starting and end-

13. Attach a 25-foot tail made of medium-weight cloth. This

You might also like