Scribd Logo
Upload

Welcome to Scribd!

  • 2K views

    Basic Turret Press Set Up Training

    Uploaded by

    Bobfarabaughjr
    The document provides instructions for setting up and operating a 344 Pega turret punch press. It describes how to select and print a part drawing, verify the work order details, locate and install the necessary tools in the turret, and load and send a program file to the machine control. The instructions are procedural and involve double clicking files, selecting options, installing tools, and using the machine's control panel buttons.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC or read online from Scribd

    Basic Turret Press Set Up Training

    Uploaded by

    Bobfarabaughjr
    2K views29 pages
    The document provides instructions for setting up and operating a 344 Pega turret punch press. It describes how to select and print a part drawing, verify the work order details, locate and install the necessary tools in the turret, and load and send a program file to the machine control. The instructions are procedural and involve double clicking files, selecting options, installing tools, and using the machine's control panel buttons.

    Original Description:

    Basic training manual for set up of Amada 344 Pega Turret Press

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    DOC or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for setting up and operating a 344 Pega turret punch press. It describes how to select and print a part drawing, verify the work order details, locate and install the necessary tools in the turret, and load and send a program file to the machine control. The instructions are procedural and involve double clicking files, selecting options, installing tools, and using the machine's control panel buttons.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC or read online from Scribd
    Download as doc
    2K views29 pages

    Basic Turret Press Set Up Training

    Uploaded by

    Bobfarabaughjr
    The document provides instructions for setting up and operating a 344 Pega turret punch press. It describes how to select and print a part drawing, verify the work order details, locate and install the necessary tools in the turret, and load and send a program file to the machine control. The instructions are procedural and involve double clicking files, selecting options, installing tools, and using the machine's control panel buttons.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC or read online from Scribd
    Download as doc
    You are on page 1of 29

    1. Open the 344 pegas folder on the desktop by double clicking.

    2. Select the part type (double click). Example: housing; rail; end cap.

    3. Select Part Number (Double click)


    4. Select “.STP” file

    5. Click file
    6. Click print

    7. Click print on pop up box


    Printing a Blue
    Print
    By Double clicking
    Print should now be printing on “big” printer.
    1. Verify part Number and Work Order quantity per
    Work Order.
    a. Make sure you have a set up sheet and Blue
    print.

    2. Locate tooling per set up sheet

    a. Check both tooling boards

    b. Check the Tooling cabinet

    c. Borrow additional tooling from the Turrets in


    the fab department

    3. Verify tool Angles and location to set up sheet

    a. Mark any tools in a different set up sheet to


    edit to

    4. Put turret in “Manual Mode” (turn Mode Select all


    the way right then 1 click to left).
    5. Turn tool change switch to “ON”

    6. Flip Index pin switch to “OUT”


    7. Open upper “Tool Change Door”

    8. Press the Pin Switch in.

    9. Use the “Turret On” buttons to spin the turret left


    or right to the desired station.

    a. Station numbers stamped on top of turret.


    10.Remove un-needed tool (if applicable); and
    install proper tool

    a. Be wary of tool angle; and remember that 0°


    for a standard punch and 0° for a special
    tool are 90° opposed to each other.
    Standard punch @ 0
    Standard Punch At 90
    Special @ 0

    Special @ 90

    11. Repeat as needed to set all tools in turret


    double-checking that none of your tools are
    crossed.

    Loading a
    program into
    the 344 Pega Q
    1. Start the Machine talk Program.
    a. The Ms talk program on the desktop
    Double click the “Machine Talk” icon.

    This is
    the main machine talk screen

    2. Select the send NC file button off of the main screen.


    3. On the next screen select either Pega 1 or Pega 2

    4. Once one of the machines is selected the “Add File”


    button will become active. Click the control to use it.

    5. When the “Add File” Button is clicked it will open a file


    open box. Click the “Browse” button.

    6. Press the down arrow in the browse box


    7. Select “344 programs” folder
    8. Select correct Pega (1 or 2)

    9. Select part Number

    10.Select “.GCD” file (Double click)


    11.Press “READ” button on turret

    12.Click “SEND FILE”

    You might also like