WWW.HIFICRITIC.

COM ISSN 1759-7919

HIFICRITIC
AUDIO REVIEW MAGAZINE 15 Vol6/No4 OCT - DEC 2012

USB CABLES COMPARED

GATHERING MOMENTUM
Dan DAgostinos striking new stereo Momentum amplier

BEAUTIFUL BODNAR?
A high value, high sensitivity single-driver speaker from Poland

A FINE IDEA
This compact oorstander provides a new entry level to Avalons range

ULTIMATE VINYL?
CB nds that the Thrax Orpheus phono stage sets a new benchmark for vinyl replay

DAB MYTHS
Under the shadow of an FM switch-off, the DAB steamroller lurches on

REVIEWED THIS ISSUE DAGOSTINO MOMENTUM STEREO SP ACOUSTICS SP1 SIGNATURE NAIM SUPERLINE/ SUPERCAP DR BODNAR SANDGLASS FANTASY NAIMUNITY 2 THRAX ORPHEUS ORTOFON ANNA AUDIO RESEARCH REF DAC DIGITAL MEDIA BRIDGE METRUM HEX CAD DAC 1543 CAMBRIDGE AUDIO DACMAGIC PLUS BULLY SOUND BSC-100M AVALON IDEA NEAT IOTA USB CABLES FROM AUDIOQUEST, CARDAS, CHORD, FURUTECH, KIMBER, QED, SUPRA and WIREWORLD
1

MUSIC & MUCH MORE

HIFICRITIC OCT | NOV | DEC 2012

rell designer Dan DAgostino had the misfortune to become embroiled in corporate issues regarding the company he started and guided for some 30 years, regretfully departing to found Dan DAgostino Master Audio Systems. The new company began operations with the Momentum monoblock power ampliers, 300W devices that sold for 35,000 a pair, and has followed this up nearly a year later with the stereo Momentum, reviewed here. A pre-amplier in similarly extrovert styling is also anticipated. (His audio electronics designer son Bret also left Krell and has started his own audio company called Bully Sound, commencing with 100W enriched Class A monoblocks at about 12,000 a pair.) Deceptively compact in the esh, the two-channel Momentum is just half the size of our reference Krell Evo 402e, and its black (or silver) satin anodised aluminium casing and heavily sculpted satin copper anks could not look more dierent. The fascia is dominated by a Cyclopian angled instrument window, its cream dial softly illuminated in tungsten and green LED lighting, wherein two opposing moving-coil meters with clock-hand needles describe a largely non-calibrated arc thats vaguely indicative of output power. A micro slide switch allows settings for 50W, 100W and 250W (full power), on an approximate peak reading, slow decay ballistic response; illumination brightness may be adjusted too. Certainly not included for decoration, those massive side panels are billets of machined copper, acting as high thermal capacity heatsinks with stepped machined apertures to encourage venturi airow with higher local velocity for increased heat
HIFICRITIC OCT | NOV | DEC 2012

Gathering Momentum
dissipation. The use of copper in such a quantity also substantially stabilises the operating temperatures of the output transistors, and will cool them more rapidly following high power transients, since copper has nearly double the thermal conductivity of aluminium at these temperatures. The sheer mass of copper used here osets its numerically lower specic heat value, and its inherently non-resonant nature also helps reduce microphony and control vibration. (Output transistors are inherently silicon crystals, and are consequently somewhat microphonic.) Coppers high performance thermal and mechanical foundation should maximise signal transparency under transient signal demands. Each channel uses an array of 16 Sanken high speed, 69MHz ft (transition frequency), locally network stabilised power transistors, arranged in

DAN DAGOSTINO FOUNDED, DESIGNED AND HEADED KRELL AMPLIFIERS FOR THIRTY YEARS. NOW HES STARTED A NEW COMPANY AND HAS INTRODUCED THE STRIKING MOMENTUM AMPLIFIERS. MARTIN COLLOMS GETS TO GRIPS WITH THE STEREO POWER AMP.
MARTIN COLLOMS

13

 REVIEW

Beware of making premature judgement on the basis of its seductive cosmetics and a seemingly blatant audio jewellery appeal to the international rich. Regardless of its glitzy attire, this amplier is not mere decoration

complementary pairs, of which two are the local drivers. High tensile non-magnetic stainless steel xings are used with optimised thermal coupling. The internal build of the mono and stereo ampliers is very similar and a stereo unit can quite quickly be converted to the 300W/ch monoblock if future upgrading is required; simply some wiring changeover, a new meter and a rear terminal panel. Low feedback means that distortion products will also be low order with some aurally agreeable even harmonic content. Precisely gain-matching the PNP/ NPN complementary output transistors also helps minimise distortion. The amplier is actually built up from below; the whole top, front and rear are carved from a single aircraft grade alloy billet. There are no microprocessors, no complex dynamic biasing schemes, just wideband, highly linear circuitry with low loop feedback. The open loop gain is only 30dB, leaving just 5dB for negative feedback, one of the lowest in the business. The technology is enriched class A/B, idling at 45W/ch (about 35 degrees Centigrade, depending on ambient). It has a clean short signal path, using discrete, wide bandwidth, all DC-coupled electronics with pre-tested components and through-hole plated PCB construction for optimal, reliable electrical connections. A smaller toroid transformer looks after low level supplies and housekeeping, including the 12V standby/remote switching loop and the display metering. The main power toroid, custom built for low noise and high regulation, is rated at 1.6kW. The on microswitch engages the start up relay, applies power and after a few seconds output is unmuted. Overload conditions will usually

instantaneously engage the input mute relay; if not the main power fuse (sucient for a maximum short term music output into 2ohm of nearly 900+ 900W) will blow. Despite its compact dimensions, DAgostinos trademark freedom from current clipping into tough loads is clearly maintained. Audio inputs are XLR balanced, and RCA/ phono adapters are included (compatible for such connection as the balanced circuitry is internally cross-coupled). Those using single-ended RCA/ phono output control units may well commission custom audio cables to avoid the adapter, which we did with a set of Transparent mm2. The speaker terminals deserve criticism. Although we coped, these are partly tucked under the small overhang of the alloy casing, are uninsulated and too closely spaced for comfort with larger audiophile cables, while the 13A IEC mains socket, 7.5A fuse and XLR audio terminals makes it all rather cramped. Transparent is considering speaker cables with more compact, right angle terminations specically to accommodate this amplier; a nut spinner is essential to obtain a stable, safe, tight contact. When in standby mode the amplier is in a very low power (2W) quiescent state, and is set into operation by a microswitch found under the front panel, below the meter. Large ngers may not quite handle this as the low prole semi-rigid feet give little clearance. A custom aluminium alloy support base is in the pipeline, and we also tried a trio of Alto Extremo Fat Boy II accessory feet (Vol5 No4) with some success. Specications tell of a nominal power of 200W/ ch 8ohm, 400/ch 4 ohm and 800/ch 2ohm; a -1dB frequency response from 1Hz to 200kHz; full power midband distortion (8ohm) of 0.15%; a 105 dB unweighted S/N ratio; and 24.5dB (x17) of voltage gain from balanced or single-ended inputs. Note that the lacquered copper nish does need careful handling. The amplier has a ve year warranty.

Sound Quality
Beware of making premature judgement on the basis of its seductive cosmetics and a seemingly blatant audio jewellery appeal to the international rich. Regardless of its glitzy attire, this amplier is not mere decoration. Almost unnoticed, this stealthy creation insinuates itself into the aural subconscious. Like a panther, dark and lithe, it makes no false sound to betray its movements and uidity. Music glides from it, untrammelled by the more common and familiar operational sounds of active electronics, with their subtle accompaniment of breathing, rustling, and grinding of the music signals owing thorough
14
HIFICRITIC OCT | NOV | DEC 2012

REVIEW

them. The Momentum does not sound like electronic machinery when reproducing sound. Most people would be unaware that such a pure quality is possible, were it not for the example of this amplier or a Robert Koda Takumi T70. (Hints of such noiseless purity, albeit necessarily at modest power outputs, may also be heard from the best singleended triode amplication.) Great as the current Krell Evo series is, not least our reference Evo 402e, which remains a class leader when properly used with matching cables and supports, DAgostino has clearly gone back to rst principles, applying all he has discovered over the years in a new a refreshing way, and it really shows. Momentum amplier technology cannot be termed a progressive improvement or a reworking of existing designs; instead it breaks new ground in reecting a cogent balance of goal-directed audio engineering. The resulting improvement in sound quality is unmistakeable and in my opinion rather more than incremental. While I truly enjoy getting to understand and appreciate incoming review gear, I only rarely encounter diculty in deciding when and how long to listen. Not so with the stereo Momentum, which immediately proved addictive. In order to get other work done I found that I had to pace myself severely. Its hard to know where to start, but theres an unmistakable rightness about the sound quality, a strong sense that all the disparate strands of previously disseminated but frequently impressive sounds are now boldly brought together in a convincing, coherent, composite whole. Sampling a variety of extracts proved impossible. So much more was going on in the soundstage, and in such a musically consonant manner, that it seemed impolite to curtail a work. Throughout, this amplier illustrated abundantly powerful musical communication skills, insisting that the listener respects the composers and performers and allows them to complete their works. I dipped into Haitink conducting Vaughan Williams Symphony Antarctica, and then found I had to play it all the way through. The same thing happened with Leftelds Lefteld, and so on. Recognisable aspects of system sound quality improvement links in the sound quality chain which I had painstakingly crafted over many years were rmly brought together, validated, clearly focused, and were somehow concentrated in the overall sound of the Momentum. Rather like the Wilson Audio MAXX 3, it makes friends with the listener, and is fun to be with. From one viewpoint this amplier simply sounds unusually correct, conrming that those sadly
HIFICRITIC OCT | NOV | DEC 2012

infrequent glimpses of quality, heard separately and to various degrees, had been correctly identied after all, and are now presented as a near totality, and in a rather convincing combination. In an audio chain, equipment performances are relative, and we struggle with alternatives and comparisons for each link trying to dene the quality and limitations of each. When a product truly jumps forward in such a quality sequence our reaction can be instinctive and reliable; in an established context you simply know when it sounds right. Theres something of the quality of the fabled Ongaku here; something of the Cary 300B SE; something of the Koda Takumi T-70, some of the Krell KSA50, some of the Evolution 600e monoblocks, some of the Audio Research D150. Experience has generally shown that brighter and more forward sounds are probably less correct. The Momentum is more distant and a little darker than nearly all the above, and in a system balanced for a normal sound it might sound restrained. I had just that experience with the ne Magico Q1, for which I preferred the Evolution 402e on the day, at least with my sources and cable combinations. As you listen at greater length the deep, deep perspectives, the remarkable illumination of the far soundstage, showing new revelations with so many familiar recordings, is close to astonishing, and thoroughly convincing. In comparison, seriously good ampliers are left sounding dynamically restrained and masked in depth and clarity. The more care taken with the system, the more this DAgostino creation revealed in the music replay. Clearly pretty good out of the box and without great adjustment, skilled system tuning then continued to bring signicant rewards in musicality and detail. Our general description of sound quality could simply be a list of excellents: for focus, stage width and depth, natural timbres, the well extended and balanced frequency response, the power and precision, the exciting and vital transient power, and the very ne rhythm and timing. Such depictions
15

 REVIEW

This amplier seems quite free from grain or hardness, capturing more of the innate tonal colour of each instrument and allowing complex themes to be followed. Piano is seriously convincing, rmly conveying the sense of performance in a beguiling manner

should also include the sense of liquid transparency; the subtle resolution and dierentiation of instrumental colour the lively attack on percussion; the preservation of instrumental character and identity; the ability to render numerous instrumentals and themes playing simultaneously in separate registration, yet continuing to hold the composition tightly together. This amplier seems quite free from grain or hardness, capturing more of the innate tonal colour of each instrument and allowing complex themes to be followed. Piano is seriously convincing, rmly conveying the sense of performance in a beguiling manner. While the above commentary rather describes the eect the amplier has on the listener, the bottom line is that it simply more accurate than most designs we have heard, and by some margin. Working with various system components, it is seriously good straight out of its transport case, but a 15-30 minute warm-up is required to reach optimum performance. After careful comparisons with references and previous tests the stereo Momentum achieved a record sound quality score of 210, and is a clear class winner.

Lab Report
Somewhat ironically in view of its great sound quality, the lab results are not as good as DAgostinos preceding Krell Evo series such as our 402e, and some mild, low order crossover or notch distortion is also detectable. Investigating crossover distortion (low order, thanks to the minimal feedback), there is some third and fth, but second harmonic is only a few dB lower, aurally leavening this mix. The distortion spectrum at 1W (Fig1 and corresponding scope trace 1b) compares with the 160W 4ohm result (waveform 1c) which is a bit rougher with visible higher harmonic transitions. But I do not think this higher distortion matters at

such a high power, where the overall distortion level is still a pretty harmless -53dB (about 0.2%). On our early sample there was also a trace of supply hum on the right channel (the one nearest the mains socket). Thus the unweighted, 1W gures are 81/85dB (right/left), low enough to be inaudible with an ear to the review loudspeaker, but perhaps not suitable for an unlikely pairing with a 105dB sensitivity horn loudspeaker. Relative to full power the results are 95/105dB unweighted, and 105dBA for both channels excluding hum. As is usual, distortion increases with power and loading, here for example to an average of 0.2% by 80W into 4ohms. Perhaps surprising is a near absence of distortion increase towards higher frequencies. At 1W the THD remained the same at just 0.06%, from 10Hz to an amazing 200kHz (noting a small power decrement at high frequencies). I ran the same graph for 50W and the distortion did not exceed 0.3% until beyond 100kHz, again showing impressive bandwidth and high frequency linearity. Here the high frequency power and load drive advantage over Class D designs is absolute. The 1W 19.5/20.5kHz high frequency intermodulation was also a very good -70dB, and a ne -63.5dB (0.07%) at full 240W/8ohm power. Output impedance is typically 0.3ohm, quite low enough, and again very constant with frequency. Frequency response, channel balance and near DC to 200kHz power bandwidth are excellent, while peak current is almost 50 amps, ample for the most taxing speaker load. High frequency intermodulation results are very good (see Fig 2), just 0.03% at 1W cruising power. Found dicult to measure, I estimate the input impedance is a high 200kohm, imposing minimal loading on sources (especially benecial for valve pre-amps). Standby power consumption is next to zero, while for the class and the high power output, the on call idle power is also modest at 90w.

DAgostino 160W 4ohm distortion waveform

DAgostino 1W 8ohm distortion waveform

16

HIFICRITIC OCT | NOV | DEC 2012

REVIEW

Channel separation was a ne 85dB midband, and 69dB by 20kHz. For the record, maximum output (242V mains) was 240W into 8ohms 20Hz to 20kHz, both channels driven, and over 445W per channel into 4ohms 20Hz to 20kHz. A single channel into 2ohms produced over 800W and into 1ohm single channel (now on music pulses) some 1.3kW. This amplier is clearly very powerful and very load capable. Its also phase-correct and has negligible DC oset.

Review System
Krell Evolution 402E power amp; Audio Research REF5 SE and Townshend Allegri control units; Linn LP12/Radikal/Keel, Naim ARO, Ortofon Anna, Koetsu Urishi Vermilion vinyl sources; Naim Superline/SupercapDR phono stage; Naim UnitiServe, MSB Platinum Signature DAC + Diamond power supply, network audio; Wilson Audio Sophia 3, 15ohm BBC LS3/5a and Quad ESL63 speakers; Finite Elemente Pagode, Extrema Fat Boy and Synergistic MIG supports; Transparent, Yter, Van den Hul and DNM cables.

AUDIO EXCELLENCE

Conclusions
Not unexpectedly, a low feedback amplier such as this doesnt break any records for numerical distortion results. Nevertheless the technical performance remains way better than required for consistently accurate sound. And we have long known that low distortion per se is not a reliable quality indicator. From an evolutionary viewpoint, DAgostino has spent years perfecting amplication in all aspects including technical parameters, but this has resulted in signicant complexity in recent times. For the Momentum models he has gone back to rst principles, with simplicity the watchword. The prime eort has been directed towards perfecting sound quality while nevertheless maintaining the load tolerance and generous power reserves for which his ampliers are so well known. Mechanically and electrically silent, the build quality and nish is also rst class, as indeed it should be at the price. But the sound is something else: highly truthful to instrumental timbres, dynamic, focused and transparent, with massive soundstages. Its also upbeat and musically involving. At the present state of the art you could hardly want for more. Highly recommended, this surprisingly compact Momentum stereo power amplier represents a substantial advance in the state of the art.

POWER AMPLFIER TEST RESULTS

Make DAgostino Date 2012-10-09 _________________________________________________________________________________ Model Momentum (stereo) Ser. No. _________________________________________________________________________________ POWER OUTPUT 20Hz 1kHz 20kHz _________________________________________________________________________________ Continuous 8 ohm 2 channel 240 W 240 W 238 W _________________________________________________________________________________ Continuous 4 ohm 1 channel 447 W 448 W 446 W _________________________________________________________________________________ Pulsed 2 ohm/1ohm 1 channel 823/1,300 W _________________________________________________________________________________ Output impedance (ohms) 0.28 ohms 0.29 ohms 0.31 ohms _________________________________________________________________________________ Peak Current 49 A _________________________________________________________________________________ Distortion, THD inc. noise 10W -55 dB -55 dB -54 dB _________________________________________________________________________________ Channel separation 88 dB 85 dB 69 dB _________________________________________________________________________________ Channel Balance Right is ref at 0dB <0.05 dB <0.05 dB <0.05 dB _________________________________________________________________________________ Frequency response -0.05 dB 0 dB -0.1 dB _________________________________________________________________________________ Intermodulation Distortion 19.5kHz/20.5kHz 1:1 rated power, 8 ohms -63.3 dB _________________________________________________________________________________ Intermodulation Distortion 19.5kHz/20.5kHz 1:1, 1W, 8 ohms -70.2 dB _________________________________________________________________________________ Signal to noise ratio ref. 1W 8ohms 77/81 dB unwtd 82/82 dBA 79.5/79.2 dB CCIR1 _________________________________________________________________________________ Signal to noise ratio ref. rated power 105/95 dB unwtd 105/105 dBA 94/95 dB CCIR1 _________________________________________________________________________________ DC oset Left 3.3 mV Right 4.3 mV _________________________________________________________________________________ Aux input balanced sensitivity ( full power 2.6V) 1W, 171 mV 200k ohms - nF _________________________________________________________________________________ Aux input single ended sensitivity 1W, 171 mV 200k ohms - nF _________________________________________________________________________________ Absolute Phase Correct _________________________________________________________________________________ Size: Width x Height x Depth 31.8 cm 15 cm 53.3 cm _________________________________________________________________________________ Price 25,000 _________________________________________________________________________________ Finish Lacquered copper sides, plus black or silver alloy casework

DAgostino 1W 8ohm 1kHz spectrum

DAgostino I/M odB 19/20kHz

Contact: Absolute Sounds www.absolutesounds.com Tel: 0208 879 7962

17

Subjective Sounds
PAUL MESSENGER

HIFICRITIC
AUDIO AND MUSIC JOURNAL BECAUSE HIFICRITIC IS FUNDED BY ITS READERS THE SUBSCRIPTION COST IS NECESSARILY HIGHER THAN FOR MAGAZINES SUBSIDISED BY ADVERTISING REVENUE, THOUGH CERTAINLY NOT AS HIGH AS PROFESSIONAL SPECIALIST JOURNALS.
ur budget is directed towards obtaining the very best research and writing from the very best freelance authors, whom we encourage to express themselves fully in print, an opportunity not always available via established publishing regimes. Through the use of a virtual oce, we aim to be exceptionally cost eective. Subscription management, production, printing, editorial, design, laboratory measurement and journalism are scattered around the world, yet are also eciently and almost instantaneously linked at the touch of an e-mail send button. Our independence from product advertising allows us to criticise and comment without fear or favour. The HIFICRITIC team scrutinises interesting and internationally important issues and equipment in depth and detail, technically and subjectively, and provides comprehensive investigations into the key issues facing high quality stereo music recording and reproduction today. Martin Colloms, Publisher SUBSCRIPTION DETAILS: Full details are provided on the WWW.HIFICRITIC.COM website, including foreign rates and secure electronic payment. If you prefer to pay direct for the UK please copy this page and send the lled in form, including a cheque payable to HIFICRITIC Ltd and send it to: HIFICRITIC, 29 Flask Walk, London NW3 1HH.
Our website supports the day-to-day activities, reports, archive and download material, while the Journal contains the primary contemporary output of our editorial team. The HIFICRITIC audio journal is a full colour print magazine with about 40,000 words of original editorial content per issue. To see what is in our most recent issue, see our current issue page.

Name ........................................................................................................................... Address ....................................................................................................................... ............................................................................................................................................. ........................................................................................................................................... Town.............................................................................................................................. Post Code .................................................................................................................. Country ....................................................................................................................... Email ............................................................................................................................. Please give your choice of issue number for start of subscription (see above) Issue no. ...........

UK SUBSCRIPTION PRICES: (mail included) 1 Year 63, expanded quarterly issues With a further, 5th issue free (25% discount)

y limited experiences with room treatment techniques have hitherto been rather disappointing. I do use some melamine foam panels between a couple of beams on the ceiling, and across a large bow window behind my main listening zone, in order to minimise midband coloration and improve stereo imaging, but more dramatic attempts to modify the behaviour of the room have not been too successful thus far. The whole issue of room treatment is controversial. Some reckon that less is more, and that one shouldnt remove any energy from the system. Others point to the fact that recording and broadcast studios use all manner of treatments to cope with the idiosyncrasies of their rooms. Irrespective of ones views, theres no denying that the room has a signicant role in the sound of a system, and my personal scepticism was well and truly tested when a friendly Dane named Ole Lund Christensen dropped o some of his large Mumax (musicus maximus!) AMA2 panels for me to try. At 999 for two Air Motion Absorber panels theyre not exactly cheap, but then neither are high quality hi- cables these days. The panels are by no means universally applicable, but they do seem eective at countering the eects of unwanted room modes. Theyre not unattractive to look at, but because theyre 195cm tall and 66cm wide (eectively doubling the latter, as theyre normally sold as freestanding hinged pairs) theyre unavoidably intrusive, especially as theyre intended to be sited well clear of a wall a key disadvantage, especially as the speakers themselves must naturally be still further out into the room. Its all to do with interfering with the velocity components of the sound energy, and as I understand it the panels need to be well out from a wall in order to aect the low frequency sound waves. Furthermore, the materials used have been carefully selected: one crucial element is a special paint that reduces the absorption at mid and high frequencies, so that the panels operate evenly right across the frequency band. Although theres no denying their intrusiveness, these panels do really work, quite dramatically so in fact. To assess them I rst brought in a pair of Spendor BC1s, a free space design with a magical midband but a known mid-bass excess. To my surprise, putting two (or three) AMM2s behind the speakers totally changed both the balance and the stereo imaging of the speakers. In this case it wasnt necessarily an improvement, but thats not relevant: whats much more signicant is that the change was far more dramatic than, for example, changing cables or support furniture. The previous and signicant 50Hz peak was reduced by a hefty 5dB, which is clearly a good thing, though the somewhat smaller 100Hz peak was increased by around 4dB. In eect, the room mode interaction of the speakers was changed considerably (though its dicult to say whether this represented a net improvement on the BC1s already good behaviour). Although not susceptible to measurement analysis, the change in imaging was no less dramatic, as the addition of the panels considerably enhanced soundstage precision and instrumental focus. Broadly similar eects were also found using a pair of Nightingale dipole speakers, which certainly seemed improved by the panels. Theres clearly scope for much more work on these Mumax panels, as I want to investigate dierent speakers and AMA2 positioning. Pro tem Ill merely say that they do work, and are one of the most interesting hi- components Ive come across recently. Check out www.actem.de for more info (assuming Christensen gets around to updating his website soon).

60

HIFICRITIC OCT | NOV | DEC 2012