PT-100 RTD 4 Wire Sensor Rosemount

Download as pdf or txt
Download as pdf or txt
You are on page 1of 8

Data Sheet

10/11 8.19 EN

FieldIT Temperature Transmitter, head mounted TH02/TH02-Ex


HART programmable, Pt 100 (RTD), thermocouples, electrical isolation

Level 0: Information

Input Resistance thermometer (2, 3, 4 wire circuit) Thermocouples Resistance remote signalling unit (0...5000 ) Voltages, mV (125...+1200 mV) Output 2 wire technique 4...20 mA, HART signal Electrical isolation (I/O) Measured error 0.1 K Customer-specific linearization 32 tie points Continuous sensor and self-monitoring Parameter saved permanently in EEPROM Monitoring of data integrety every 10 s Wire break monitoring in acc. with NAMUR NE 89 Substitution strategy in case of error (NE 43) Approvals for explosion protection Intrinsically safe II 2 (1) G EEx [ia] ib IIC T6, mount in zone 1 II 3 G EEx n A II T6, mount in zone 2 Input functionality (absolute, differential, average value) EMC acc. to EN 50082-2 and NE 21 Parameterization Device Management Tool: SV401 (SMART VISION) Hand held terminals: 691HT, STT04, HHT275 CoMeter (HART configurator/LC display) 5 years warranty

Excellent long term stability Temperature linear output signal Enhanced self diagnostics

Temperature Transmitter, head mounted TH02/TH02-Ex HART programmable, Pt 100 (RTD), thermocouples, electrical isolation

10/11 8.19 EN

Technical data
Output
Output signal (temperature linear) 4...20 mA Residual ripple (peak-to-peak) < 0.3 % Current consumption < 3.6 mA Maximum output current 23.6 mA Parameterizable current error signal Underranging 3.6 mA Overranging 22 mA Default value 3.6...23.6 mA Damping t63 = 0...30 s

Sensor short-circuit < 5 (for RTD) Sensor break (temperature/resistance measurement 2, 3, 4 wire) Measuring range 0... 500 > 530 Measuring range 0...5000 > 5.3 k Sensor wire break monitoring in accordance with NAMUR NE 89 Sensor wire break detection 3 wire resistance measurement > 35 4 wire resistance measurement > 3.7 k Input filter 50/60 Hz

Thermocouples
Types B, E, J, K, L, N, R, S, T, U Voltages 125 mV...+ 125 mV 125 mV...+1200 mV Minimum measuring span 2 mV/50 mV Sensor wire break monitoring in accordance with NAMUR NE 89 Pulsed with 1 A outside of the measuring interval Monitoring disconnectible Thermocouple measurement > 5 k Voltage measurement > 5 k Input filter 50/60 Hz Internal reference junction Pt 100, via software switchable (no jumper necessary)

Input
Resistance
Resistance thermometer (IEC 751, JIS, SAMA) n Pt 100/Ni 100 to Pt 1000/Ni 1000; Cu (n = 0.1, 0.2, 0.5, 1, 1.2, 2, 3...10) Min. measuring span 15 K/50 K Resistance 0...500 /0...5000 Min. measuring span 5 /50 Maximum line resistance (Rw) per core 2, 3, 4 wire 7.5 , 10 , 50 Measuring current 300 A

Input element Standard IEC 584 1 Sensor Thermocouple type B Thermocouple type E Thermocouple type J Thermocouple type K Thermocouple type R Thermocouple type S Thermocouple type T Thermocouple type N Thermocouple type L Thermocouple type U Resistance thermometer Pt 100 Resistance thermometer Pt 1000 Resistance thermometer Ni 100 Resistance thermometer Ni 500 mV

Measuring range 250...+1820 C 250...+1000 C 210...+1200 C 250...+1372 C 50...+1768 C 50...+1768 C 200...+ 400 C 200...+1350 C (+482...+3308 F) (418...+1832 F) (346...+2192 F) (418...+2502 F) ( 58...+3215 F) ( 58...+3215 F) (328...+ 752 F) (328...+2462 F)

Min. measuring span 235 C 30 C 37 C 54 C 171 C 193 C 50 C 60 C 36 C 40 C 15 C 50 C 8 C 15 C 5 /50 2 mV 50 mV (423 F) ( 54 F) ( 67 F) ( 98 F) (308 F) (348 F) ( 90 F) (108 F) ( 65 F) ( 72 F) ( 28 F) ( 90 F) ( 15 F) ( 28 F)

DIN 43710 IEC 751; JIS; SAMA1) 2, 3 and 4 wire DIN 437602) 2, 3 and 4 wire Resistance Voltage

200...+ 900 C ( 76...+ 482 F) 200...+ 600 C (328...+1112 F) 200...+ 850 C (328...+1562 F) 200...+ 850 C (328...+1562 F) 60...+ 250 C ( 76...+ 482 F) 60...+ 250 C ( 76...+ 482 F) 0...500 /0...5000 125 mV...+ 125 mV 125 mV...+1200 mV

1) 2)

IEC 751 a = 0.00385, JIS a = 0.003916, SAMA a = 0.003902 Edison Curve No. 7

Temperature Transmitter, head mounted TH02/TH02-Ex HART programmable, Pt 100 (RTD), thermocouples, electrical isolation

10/11 8.19 EN

Power supply (poling protected)


Supply voltage Non Ex application Us = 8.5...30 V DC For Ex Application, max. Ui = 8.5...29.4 V DC 2 wire methode: power supply wires = signal wires Influence of supply voltage < 0.05 %/10 V maximum residual ripple 1 % US (< 500 Hz)

Mechanical construction
Dimensions Confer dimensional drawing Weight 55 g Housing material Polycarbonat black (Non Ex type) blue (Ex type)

Power demand of indicators (only with AGLHD head)


(Power demand of transmitter and indicator have to be added)
Digital indicator Usd = 2 V DC CoMeter (HART configutor/LC display) Usd = 2.9 V DC

Electrical connection
Terminals, pluggable 2.5 mm2, screw terminals (stainless steel screws)

Characteristics at rated conditions


According to IEC 770 (related to 25 C)1)
Digital measured error Pt 100 Thermocouples Linear resistance 500 /5000 Linear voltage 120 mV/1200 mV D/A measured error 0.05 % of measuring span Additional influence of the internal reference junction Pt 100 DIN IEC 751 Kl. B
t ra io n n ra ge

Maximum load

( U smax U smin ) R ( k ) = --------------------------------------23.6

0.1 K 20 V 40 m/200 m 20 V/50 V

910

Maximum permissible load R

788

With CoMeter

Influences
Influence of ambient temperature Pt 100/resistance measurement2)
30

250

(HC)

pe

0 8,5 11,4 14,4 17,3


Z-20160

V DC Power supply Us

ME ( ) < ( 0.05 % + -------------------- 0.008 % ) 10 K MS ( ) Thermocouple/mV3)

General characteristics
Output signal refreshment rate Pt 100 0.4 s (Input signal change < 0.25 K/s) Thermocouples 0.2 s (Input signal change < 2.5 K/s) Vibration resistance Vibration in operation Resistance to shock Electrical isolation (I/O) 1.5 kV AC (60 s) Long-term stability 0.1 % p.a. 2g acc. to DIN IEC 68T.2 6 acc. to DIN IEC 68T.2 27
1) 2)

ME ( mV ) 0.14 K < ( 0.05 % + ------------------------ 0.01 % + ------------------ 100 % ) 10 K MS ( mV ) MS ( K ) Percentage related to measuring span MS = ME MA MA = lower range value, ME = upper range value

Percentage related to set measuring span Specified values corresponds to 3 (Gaussian normal distribution) Pt 100 (0...400 C): Influence of ambient temperature < (0.05 % + 0.013 %)/10 K = 0.063 %/10 K 3) Type K (0...1000 C): Influence of ambient temperature < (0.05 % + 0.01 % + 0.014 %)/10 K = 0.074 %/10 K

Environment conditions
Ambient temperature range 40...85 C Transport and storage temperature 40...100 C Relative humidity < 100 % (100 % humidity with isolated terminals only) Condensation Permitted

Temperature Transmitter, head mounted TH02/TH02-Ex HART programmable, Pt 100 (RTD), thermocouples, electrical isolation

10/11 8.19 EN

Explosion protection
Intrinsically safe
Zone 1 Marking EC Type Examination certificate Temperature class T6/T5/T4 Supply circuit Max. voltage Short circuit current Max. power Internal inductance Internal capacitance Output [ib] Ui = 29.4 V Ii = 130 mA Pi = 0.8 W Li = 220 H Ci = 15 nF II 2 (1) G EEx [ia] ib IIC T6 PTB 99 ATEX 2139 X 50 C/65 C/85 C Input [ia] Uo = 5.6 V Io = 1.5 mA4) Po = 20 mW Lo = 1 mH Co = 1.55 F

Electromagnetic compatibility (EMC)


Pt 100: measuring range 0...100 C, span 100 K Type of test Burst to signal/ data lines Static discharge Contact plate (indirect) Terminals for supply5) Terminals for sensors5) Radiated field 80 MHz...1 GHz Coupling 150 kHz 80 MHz Degree 3 kV Influence < 0.1 % IEC 1000 4 4 1000 4 2 8 kV 6 kV 4 kV 10 V/m 10 V no influence no influence no influence 1000 4 3 < 1.0 % 1000 4 6 < 1.0 %

According to NAMUR NE 21 recommendation. In case of an input signal change > 0.25 K/s for Pt100 or > 2.5 K/s for thermocouples a measured value plausibility check is performed.

Zone 2 Marking Conformity statement Temperature class T6/T5/T4

II 3 G EEx n A II T6 PTB 99 ATEX 2216 X 50 C/65 C/85 C


5)

Air discharge (at 1 mm distance)

Canadian Standards Association and Factory Mutual


Intrinsically Safe FM CSA Class I, Div. 1, Groups A, B, C, D T6 Class I, Zone 0, Group IIC T6 Class I, Div. 1 and Div. 2, Groups A, B, C, D T6 Class I, Zone 0, Group IIC T6 (Class II Groups E, F, G; Class III if build in BUZH , AGL oder AGLH Kopf) Class I, Div. 2, Groups A, B, C, D, T6 Class I, Div. 2, Groups A,B,C,D T6 (Class II, Groups E, F, G; Class III wenn einge baut in BUZH , AGL oder AGLH Kopf)

Nonincendive FM CSA

4)

See 1. supplement PTB 99 ATEX 2139 X

Temperature Transmitter, head mounted TH02/TH02-Ex HART programmable, Pt 100 (RTD), thermocouples, electrical isolation

10/11 8.19 EN

Displays (option in conjunction with AGLHD head)


Digital display

Digital display
Process value, sensor value or loop current value indicator Fed through current loop LC display: 3 digits ( 1999), digit height 10 mm, 7 segments Standard scaling 0...100 % Linear scaling for measuring ranges and units possible Description of the physical unit (labels)

CoMeter (HART configurator and LC display)

CoMeter (HART configurator and LC display)


4 function keys for request and programming (Code protection) Fed through current loop LC display: 5 digits ( 1999), digit height 7,6 mm, 7 segments Sign and floating point 10 segment bargraph (heading of measuring range) 7 digits alphanumeric characters 6 mm, 14 segments Dual function HART transmitter programming unit (all HART functions except for freely configurable characteristic curve and TAG Number) Process value, sensor value or loop current value indicator Request function Process variable, analog and display value, description of measuring point, serial number, error behaviour, lower/upper measuring range limit Change function Sensor type,sensor circuit, measuring range, damping, mains filter, error signalling Special function Zero point adjustment, simulation of output signal, adjustment of output signal, wet calibration
Display Response time Measuring error Overvoltage or maximum current EMC Temperature Humidity Digital display CoMeter 0.5 s 1.3 s 0.1 % 0.15 % 150 % of 215 mA input range EN 50082 2 20...+70 C 0...100 %, condensating permitted

Mind limits of application

Communication/parameterization
Hand held terminal HHT 691HT, STT04, HHT275 CoMeter Hart conigurator and LC display Device Management Tool SV401 (SMART VISION) Parameter Sensor type, error signalling, measuring range, general characteristics (i. e. TAG number), damping, signal simulation of output Software interface AMS, Cornerstone

CoMeter

Processinterface Line resistance


+

(250 min.)*

or Isolators Controller Recorders

691HT, STT04, HHT275

Z-20162d

GND
or

(optional) FSK Modem


*if necessary

Temperature Transmitter, head mounted TH02/TH02-Ex HART programmable, Pt 100 (RTD), thermocouples, electrical isolation

10/11 8.19 EN

Connection diagram

Microprocessor

1
Input

+
Us = 8,5...30 V DC
Output

K1
3 +
3 3 3 3

3 3

K1
3 3 3

4...20 mA
Reference junction

4 4

K2
4

K2
4 4

4 +

2
2 2 2 2 2

V DC

V DC

a)

b)

c)

d)

e)

f)

g)

h)

i)

a) b) c) d)

Resistance thermometer, 2 wire circuit Resistance thermometer, 3 wire circuit Resistance thermometer, 4 wire circuit Double resistance thermometer, 2 wire circuit (average value or differential temperature measurement) e) Potentiometer input, 4 wire circuit

f) Thermocouple g) Double thermocouple (average value or differential temperature measurement) h) Voltage measurement i) Double voltage measurement (average value or differential temperature measurement)

Dimensional diagram (dimensions im mm)

Automation - Products Contrans TH 02


Messumformer/Transmitter/Transducteur

3
Z-18763h

44

5,5

22,5

Z-20165

Temperature Transmitter, head mounted TH02/TH02-Ex HART programmable, Pt 100 (RTD), thermocouples, electrical isolation

10/11 8.19 EN

Ordering information
Catalog No. TH02/TH 02-Ex V11518(without Ex) 1 TH02 Type of protection: intrinsically safe ATEX II 2 (1) G EEx [ia]ib IIC T6 5 TH02-Ex Zone 1: ATEX II 3 G EEx n A II T6 N TH02-Ex N Zone 2: FM 7 TH02-Ex IS Class I, Div. 1, Groups A, B, C, D T6 IS Class I, Zone 0, Group IIC T6 CSA 9 TH02-Ex IS Class I, Div.1 and Div. 2, Groups A, B, C, D T6 (Class II Groups E, F, G; Class III If build in BUZH head, AGL head or AGLH head) Nonincendive, Class I, Div. 2, Groups A, B, C, D T6 (Class II, Groups E, F, G; Class III if built in BUZH head, AGL head or AGLH head) FM M TH02-Ex N nonincendive, Class I, Div. 2, Groups A, B, C, D T6 Construction / display Module (h = 22.5 mm) Module (h = 22.5 mm) with sensor connecting line Module (h = 22.5 mm) with snap-on fixing Module (h = 27.5 mm) for mounting on measuring module Module built into connection head or cover with sensor connecting line BUZH head BUSH head BUKH-Ex head Raised B-head cover B head (completely head with raised cover) AUZH head AUSH head AGL head1) without display AGLHD head1) with digital display AGLHD head1) with cometer Attention: The sensor connecting lines correspond to the order for the type of sensor or its type of circuitry Module built into field housing: Aluminium field housing 80 x 75 x 57 mm, IP 65; 2 x M16 x 1.5 Polyester field housing 75 x 80 x 55 mm, IP 65; 2 x M16 x 1.5 Aluminium field housing 80 x 175 x 57 mm, IP 65; 1 x M16 x 1.5; 1 x M20 x 1.5 with separate terminal block Polyester field housing 75 x 190 x 55 mm, IP 65; 1 x M16 x 1.5; 1 x M20 x 1.5 with separate terminal block Notice: Other field housings with several transmitters or specially for pipe mounting on request. Programming Factory standard parameter Pt 100, 0...100 C, 4 wire circuit, damping off, direct action characteristic overranging at sensor or device error (22 mA) Customer-specific parameter setting (questionnaire) without Calibration certificates 2 point 9 point EUR 220,50 * 247,80 * 247,80 * 247,80 * 247,80 * Deliv. time 3 wks.

247,80 * 3 1 4 Z R P N L K V U X D C 7,40 * 9,70 * 5,40 * 40,10 40,60 32,60 19,20 22,90 53,60 54,80 77,80 254,10 298,00 * * * * * * * * * *

A 9 F E

70,40 * 73,00 * 86,40 * 94,50 *

0 1 0 1 2

21,50 * 75,60 * 107,10 *

Accessories
ABB FSK modem [EEx ib] IIC (parameter setting in the installation) Device Management Tool SV401 (SMART VISION) TH02 /-102 /-202 driver for AMS software 1.4 (Rosemount)2)
1)

Catalog No. see Data Sheet 10/63-6.71 EN see Data Sheet 10/63-1.20 EN 7957771

EUR

Deliv. time

107,10 *

Standard: Aluminium, metal-cable-screw-connection M20 x 1.5 EEx e; protective pipe connection M24 x 1.5 (optional M20 x 1.5; 1/2" NPT; 3/4" NPT); (do not use for EEx d applications, see data sheet 10/10-3.28 EN for EEx d details) 2) already integrated in AMS software version 5.0 or higher Notice: For a lokal programming on the desk can used as Hardware the universal FSK-Programming-Set (without Parasoft) (see Data Sheet 10/63-6.71 EN: ordering information) .

The IndustrialIT wordmark and all mentioned product names in the form XXXXXXIT are registered or pending trademarks of ABB. ABB has Sales & Customer Support expertise in over 100 countries worldwide. www.abb.com

The Companys policy is one of continuous product improvement and the right is reserved to modify the information contained herein without notice. Printed in the Fed. Rep. of Germany (10.02) ABB 2002

ABB Ltd. Salterbeck Trading Estate Workington, Cumbria CA14 5DS UK Tel: +44 (0)1946 830 611 Fax: +44 (0)1946 832 661

ABB Inc. 125 E. County Line Road Warminster, PA 18974 USA Tel: +1 215 674 6000 Fax: +1 215 674 7183

ABB Automation Products GmbH Borsigstr. 2 63755 Alzenau Germany Tel: +49 6023 92 0 Fax: +49 6023 92 3430

10/11 8.19 EN Rev. A

You might also like