Scribd
Upload
138 views

Lab 7.2.3.3 Configuring and Verifying A PPP Link: CCNA Discovery Introducing Routing and Switching in The Enterprise

dhdhdhdhhdhdhddhdhd

Uploaded by

mohammad_shahzad_iiui
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
138 views

Lab 7.2.3.3 Configuring and Verifying A PPP Link: CCNA Discovery Introducing Routing and Switching in The Enterprise

dhdhdhdhhdhdhddhdhd

Uploaded by

mohammad_shahzad_iiui
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

CCNA Discovery Introducing Routing and Switching in the Enterprise

Lab 7.2.3.3 Configuring and Verifying a PPP Link

Device

Host Name R1 R2

Serial 0/0/0 IP Address 192.168.15.1 192.168.15.2

Subnet Mask 255.255.255.252 255.255.255.252

Serial 0/0/0 Interface Type DCE DTE

Enable Secret Password class class

Enable, vty, and Console Password cisco cisco

Router 1 Router 2

Objectives
Configure the serial interfaces on two routers to use PPP. Verify and test the link for connectivity.

Background / Preparation
Cable a network similar to the one shown in the topology diagram. Any router that has a single serial interface may be used for this lab. For example, router series 800, 1600, 1700, 1800, 2500, 2600, 2800, or any combination are acceptable. The information in this lab applies to other routers; however, command syntax may vary. Depending on the router model, the interfaces may be identified differently. For example, on some routers, Serial 0 may be Serial 0/0 or Serial 0/0/0 and Ethernet 0 may be FastEthernet 0/0. The information in this lab applies to routers that use the Serial 0/0/0 notation. If the router in use differs, use the correct notation for the serial interface. The following resources are required: Two routers both with a serial interface Two Windows-based PCs, each with a terminal emulation program

All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 1 of 4

CCNA Discovery Introducing Routing and Switching in the Enterprise


At least one RJ-45-to-DB-9 connector console cable to configure the routers One 2-part (DTE/DCE) serial cable NOTE: Make sure that the routers and the switches have been erased and have no startup configurations. Instructions for erasing both switch and router are provided in the Lab Manual, located on Academy Connection in the Tools section. NOTE: SDM Enabled Routers If the startup-config is erased in an SDM enabled router, SDM will no longer come up by default when the router is restarted. It will be necessary to build a basic router configuration using IOS commands. The steps provided in this lab use IOS commands and do not require the use of SDM. If you wish to use SDM, refer to the instructions in the Lab Manual, located on the Academy Connection in the Tools section or contact your instructor if necessary.

Step 1: Connect the equipment


Connect Router 1 and Router 2 with a serial cable connecting both Serial 0/0/0 interfaces as shown in the topology diagram.

Step 2: Perform basic configuration on Router 1


a. Connect a PC to the console port of the router to perform configurations using a terminal emulation program. On Router 1, configure the hostname, IP addresses, and passwords as provided in the addressing table. Save the configuration.

Step 3: Perform basic configuration on Router 2


On Router 2, configure the hostname, IP addresses, and passwords as provided in the addressing table. Save the configuration.

Step 4: Show the details of Serial 0/0/0 interface on R1


Enter the command show interface serial 0/0/0 to view the details of the interface. R1#show interface serial 0/0/0 What is the status of Serial 0/0/0? __________ Line Protocol is __________ The Internet address is ______________________________ Encapsulation is __________

Step 5: Show the details of Serial 0/0/0 interface on R2


Enter the command show interface serial 0/0/0 to view the details of the interface. R2#show interface serial 0/0/0 What is the status of Serial 0/0/0? __________ Line Protocol is __________ The Internet address is ______________________________ Encapsulation is __________

All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 2 of 4

CCNA Discovery Introducing Routing and Switching in the Enterprise


Step 6: Turn on PPP debugging
Turn on the PPP debug function on both routers by entering debug ppp negotiation at the privileged EXEC mode prompt. R1#debug ppp negotiation R2#debug ppp negotiation NOTE: Debugging output is assigned high priority in the CPU process and can render a system unusable. When working on a live network, use debug only during periods of low network traffic.

Step 7: Change the encapsulation type


a. Change the encapsulation type to PPP by entering encapsulation ppp at the interface Serial 0/0 configuration mode prompt on both routers. R1(config-if)#encapsulation ppp R2(config-if)#encapsulation ppp What did the debug function report when the PPP encapsulation was applied to each router? _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ Turn off the debug function by entering undebug all at the privileged EXEC mode prompt of both routers. R1#undebug all R2#undebug all

Step 8: Show the details of Serial 0/0/0 interface on R1


Enter the command show interface serial 0/0/0 to view the details of the interface. R1#show interface serial 0/0/0 What is the status of Serial 0/0/0? __________ Line Protocol is __________ The Internet address is ______________________________ Encapsulation is __________

Step 9: Show the details of Serial 0/0/0 interface on R2


Enter the command show interface serial 0/0/0 to view the details of the interface. R2#show interface serial 0/0/0 What is the status of Serial 0/0/0? __________ Line Protocol is __________ The Internet address is ______________________________ Encapsulation is __________

All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 3 of 4

CCNA Discovery Introducing Routing and Switching in the Enterprise


Step 10: Verify that the serial connection is functioning
a. Ping from R1 to R2 to verify that there is connectivity between the two routers. R1#ping 192.168.15.2 R2#ping 192.168.15.1 Can the serial interface on the R2 router be pinged from R1? __________ Can the serial interface on the R1 router be pinged from R2? __________ If the answer is no for either question, troubleshoot the router configurations to find the error. Repeat the pings until they are successful.

Step 11: Reflection


a. What command allows you to view the details of a specific interface? _______________________________________________________________________________ _______________________________________________________________________________ When should you use the debug function in a router? _______________________________________________________________________________ _______________________________________________________________________________ _______________________________________________________________________________ What is the default serial encapsulation on a Cisco router? _________________________

All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.

Page 4 of 4

You might also like